A lightweight, 70 cm diameter parabolic reflector with pole/mast mounting bracket and feed guide The Kraken Discovery Dish is a 70-cm aluminum satellite dish with an active filtered feed. It is designed for receiving real-time weather data from GOES HRIT, GK-2A LRIT, FengYun LRIT, NOAA HRPT, Metop HRPT, Meteor M2 HRPT, and other weather satellites that operate around 1.69 GHz. The dish weighs less than one kilogram and splits into three petals for easy shipping. The 1.69 GHz feed contains a built-in LNA and filter right at the feed point, which means there is almost no noise figure loss from cables or connectors. The feed electronics are encased in a waterproof enclosure, meaning no external waterproofing work is required. There are also feeds for 1.42 GHz hydrogen line radio astronomy and 1.5 GHz Inmarsat STD-C and AERO. To amplify the weak signals transmitted by weather satellites, Discovery Dish incorporates the Qorvo QPL9547 high-linearity, ultra-low-noise amplifier in a small 2 x 2 mm surface-mount package. Included 1x 70 cm diameter lightweight aluminum dish (three petals) + screws 1x Dish-to-pole mount Required (at least one) 1x L-Band Weather Satellite Discovery Feed 1x Inmarsat Discovery Feed 1x Hydrogen Line Discovery Feed

Read more less

The Siglent SDS814X HD digital storage oscilloscope is based on 2 GSa/s, 12-bit Analog-Digital Converters and front ends with excellent noise floor performance. With a 100 MHz bandwidth, and a maximum record length of 50 Mpts, and the capability to analyze 4 analog channels alongside 16 digital channels, the SDS814X HD is perfectly suited for mixed signal analysis. Features 12-bit High Resolution 12-bit Analog-Digital Convertors with sample rate up to 2 GSa/s Front ends with 70 μVrms noise floor @ 100 MHz bandwidth 2/4 analog channels, up to 700 MHz bandwidth SPO technology Waveform capture rate up to 80,000 wfm/s (normal mode), and 500,000 wfm/s (sequence mode) Supports 256-level intensity grading and color temperature display modes. Up to 50 Mpts record length Digital trigger system Intelligent trigger: Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video (HDTV supported), Qualified, Nth edge, Delay, Setup/Hold time. Serial bus triggering and decoder, supports protocols I²C, SPI, UART, CAN, LIN. Segmented acquisition (Sequence) mode, dividing the maximum record length into multiple segments (up to 80,000), according to trigger conditions set by the user, with a very small dead time between segments to capture the qualifying event. History waveform record (History) function, the maximum recorded waveform length is 80,000 frames. Automatic measurements on 50+ parameters, supports statistics with histogram, track, trend, Gating measurement, and measurements on Math, History and Ref. 4 Math traces (2 Mpts FFT, addition, subtraction, multiplication, division, integration, differential, square root, etc.), supports formula editor. Abundant data analysis functions such as Search, Navigate, Counter, Bode plot and Power Analysis High Speed hardware-based Mask Test function, with Mask Editor tool for creating user-defined masks 16 digital channels (optional) 25 MHz waveform generator (optional) 7" TFT-LCD display with 1024 x 600 resolution; Capacitive touch screen supports multi-touch gestures. Interfaces include: USB Hosts, USB Device (USBTMC), LAN (VXI-11/Telnet/Socket), Pass/Fail, Trigger Out Built-in web server supports remote control over the LAN port using a web browser. Supports SCPI remote control commands. Supports external mouse and keyboard. Supports NTP. Specifications Analog Channels 4 Bandwidth 100 MHz Vertical resolution 12-bit Sample rate (Max.) One channel mode: 2 GSa/sTwo channel mode: 1 GSa/sFour channel mode: 500 MSa/s Memory depth (Max.) One channel mode: 50 Mpts/chTwo channel mode: 25 Mpts/chFour channel mode: 10Mpts/ch Waveform capture rate (Max.) Normal mode: 80,000 wfm/sSequence mode: 500,000 wfm/s Trigger type Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video, Qualified, Nth edge, Delay, Setup/Hold time, Serial Serial trigger and decode (Standard) I²C, SPI, UART, CAN, LIN Measurement 50+ parameters, statistics, histogram, trend, and track supported Math 4 traces 2 Mpts FFT, Filter, +, -, x, ÷, ∫dt, d/dt, √, Identity, Negation, Absolute, Sign, ex, 10x, ln, lg, Interpolation, MaxHold, MinHold, ERES, Average. Supports formula editor Data analysis Search, Navigate, History, Mask Test, Counter, Bode plot, and Power Analysis Digital channel (optional) 16-channel; maximum sample rate up to 1 GSa/s; record length up to 10 Mpts USB AWG module (option) One channel, 25 MHz, sample rate of 125 MHz, wave length of 16 kpts, isolated output I/O 2x USB 2.0 Host, USB 2.0 Device, 10/100 M LAN, Auxiliary output (TRIG OUT, PASS/FAIL), SBUS (Siglent MSO) Probe (Standard) Passive probe PB470 for each channel Display 7 TFT-LCD with capacitive touch screen (1024x600) Included 1x Siglent SDS814X Oscilloscope 4x Passive probe (100 MHz) PP510 1x Power cord (EU) 1x USB cable 1x Certificate of calibration 1x Quick start Downloads Datasheet Manual Programming guide

Read more less

The OWON SPS3081 Fanless Programmable DC Power Supply (120 W) delivers ultra-quiet, high-precision performance with 10 mV/1 mA accuracy and advanced heat dissipation for long-term reliability. Featuring comprehensive protection, a USB interface with SCPI support for remote control, and a 2.8-inch TFT LCD screen, it is the perfect choice for laboratories, electronics testing, and research. Features Fanless design: Ultra-quiet operation, reducing vibration noise and minimizing the potential failure risks associated with traditional cooling fans. Excellent heat dissipation design: Ensures a controlled temperature rise, allowing long-term operation under full load conditions and extending internal component longevity. Lightweight and ultra-thin design. Output accuracy up to 10 mV/1 mA. Supports List waveform editing and output, with four memory shortcut parameters for quick and convenient access. Integrated protection features include overvoltage, overcurrent, overtemperature, and input undervoltage protection for enhanced safety. Built-in discharge circuit prevents residual high voltage risks when the power is turned off. USB communication interface with SCPI protocol support, enabling PC programming and remote control for simplified user management. 2.8-inch TFT LCD screen Specifications Model SPS6051 SPS3081 Rated Output (0°C-40°C) Voltage 0-61 V 0-31 V Current 0-5.1 A 0-8.1 A Power 150 W 120 W Load Regulation Voltage ≤30 mV Current ≤20 mA Power Regulation Voltage ≤30 mV Current ≤20 mA Setting Resolution Voltage 10 mV Current 1 mA Readback Resolution Voltage 10 mV Current 1 mA Seting Accuracy (25°C ±5°C) Voltage ≤0.05% ±20 mV ≤0.1% ±20 mV Current ≤0.05% ±20 mA ≤0.2% ±20 mA Readback Accuracy (25°C ±5°C) Current ≤0.05% ±20 mV ≤0.1% ±20 mV Voltage ≤0.05% ±20 mV ≤0.2% ±20 mA Ripple/Noise Voltage ≤30 mVp-p ≤30 mVp-p Voltage ≤4 mVrms ≤5 mVrms Current ≤10 mAp-p ≤30 mAp-p Output temperature coefficient (0°C-40°C) Voltage 100 ppm/°C Current 200 ppm/°C Readback temperature coefficient Voltage 100 ppm/°C Current 200 ppm/°C Response Time (50-100% rated load) ≤1.0 ms Storage 4 groups of data Working Temperature 0-40°C Display 2.8-inch color LCD display Interface USB Dimensions (W x H x D) 82 x 142 x 226 mm Weight 1.8 kg Included 1x OWON SPS3081 Power Supply 2x Test leads 1x Power cord 1x Manual Downloads Datasheet User Manual Programming Manual PC Software

Read more less

The SDRplay RSPdx-R2 is a wideband full featured single-tuner 14-bit SDR receiver which covers the entire RF spectrum from 1 kHz to 2 GHz giving up to 10 MHz of spectrum visibility. It contains three antenna ports, two of which use SMA connectors and operate across the full 1 kHz to 2 GHz range and the third uses a BNC connector which operates up to 200 MHz. The RSPdx-R2 is an enhanced version of the RSPdx with further design improvements for use at frequencies below 2 MHz. Housed in a strong steel case, in addition to the functionality of the RSP1B, the RSPdx-R2 provides three software selectable antenna inputs and an external clock input. It offers excellent performance through HF and VHF frequencies all the way up to 2 GHz. The RSPdx-R2 also supports an "HDR mode" optimised for the demanding radio reception conditions below 2 MHz. The RSPdx-R2, when used in conjunction with SDRplay’s own software, introduces a special HDR (High Dynamic Range) mode for reception within selected bands below 2 MHz. HDR mode delivers improved intermodulation performance and fewer spurious responses for those challenging bands. Features Covers all frequencies from 1 kHz through VLF, LF, MW, HF, VHF, UHF and L-band to 2 GHz, with no gaps Receive, monitor and record up to 10 MHz of spectrum at a time Significantly improved noise performance below 1 MHz (i.e. for some MF, LF and below) Improved dynamic range below 2 MHz both in tuner mode and HDR mode HDR mode below 2 MHz giving overall dynamic range and selectivity advantages Software selectable choice of 3 antenna ports External clock input for synchronisation purposes, or connection to GPS reference clock for extra frequency accuracy Excellent dynamic range for challenging reception conditions Free use of Windows-based SDRuno software (check website for versions supported) Free use of SDRconnect SDR and server software for Windows, MacOS and Linux (Check website for versions supported) Multiplatform driver and API support including Windows, Linux, Mac and Raspberry Pi 4/5 Strong and growing software support network Calibrated S meter/RF power and SNR measurement with SDRuno (including datalogging to .CSV file capability) Documented API provided to allow demodulator or application development on multiple platforms Applications (Amateur) Shortwave radio listening Broadcast DXing (AM/FM/TV) Panadaptor Aircraft (ADS-B and ATC) Slow Scan TV Multi-amateur band monitoring WSPR & digital modes Weather fax (HF and satellite) Satellite monitoring Geostationary environmental satellites Trunked radio Utility and emergency service monitoring Fast and effective antenna comparison Applications (Industrial) Spectrum Analyser Surveillance Wireless microphone monitoring RF surveying IoT receiver chain Signal logging RFI/EMC detection Broadcast integrity monitoring Spectrum monitoring Power measurement Applications (Educational/Scientific) Teaching Receiver design Radio astronomy Passive radar Ionosonde Spectrum analyser Receiver for IoT sensor projects Antenna research Specifications Frequency Range 1 kHz – 2 GHz Antenna Connector SMA Antenna Impedance 50 Ohms Current Consumption (Typical) 190 mA @ >60 MHz (excl. Bias-T)120 mA @ <60 MHz (excl. Bias-T) USB Connector USB-B Maximum Input Power +0 dBm Continuous+10 dBm Short Duration ADC Sample Rates 2-10.66 MSPS ADC Number of Bits 14 bit 2-6.048 MSPS12 bit 6.048-8.064 MSPS10 bit 8.064-9.216 MSPS8 bit >9.216 MSPS Bias-T 4.7 V100 mA guaranteed Reference 0.5ppm 24 MHz TCXOFrequency error trimmable to 0.01ppm in field Operating Temperature −10˚C to +60˚C Dimensions 113 x 94 x 35 mm Weight 315 g Downloads Datasheet Software RSPdx-R2 vs RSPduo RSPdx-R2 RSPduo Continuous coverage from 1 kHz to 2 GHz ✓ ✓ Up to 10 MHz visible bandwidth ✓ ✓ 14-bit ADC silicon technology plus multiple high-performance input filters ✓ ✓ Software selectable AM/FM & DAB broadcast band notch filters ✓ ✓ 4.7 V Bias-T for powering external remote antenna amplifier ✓ ✓ Powers over the USB cable with a simple type B socket ✓ ✓ 50Ω SMA antenna input(s) for 1 kHz to 2 GHz operation (software selectable) 2 2 Additional software selectable Hi-Z input for up to 30 Mhz operation ✓ Additional software selectable 50Ω BNC input for up to 200 MHz operation ✓ Additional LF/VLF filter for below 500 kHz ✓ 24 MHz reference clock input (+ output on RSPduo) ✓ ✓ Dual tuners enabling reception on 2 totally independent 2 MHz ranges ✓ Dual tuners enabling diversity reception using SDRuno ✓ Rugged black painted steel case ✓ ✓ Overall performance below 2 MHz for MW and LF ++ + Multiple simultaneous applications + ++ Performance in challenging fading conditions (*using diversity tuning) + *++

Read more less

The Siglent SPD4323X is a 4-channel DC Linear Programmable Power Supply equipped with a 4.3-inch TFT-LCD display, friendly human-machine interface, and excellent performance indicators. Real-time waveform display provides engineers with an informative user interface. SPD4323X offers a total output power of 240 W with a resolution of 1 mV/1 mA. The maximum voltage and current for each channel are as follows: CH1: 6 V/3.2 A CH2: 32 V/3.2 A CH3: 32 V/3.2 A CH4: 6 V/3.2 A Features Rated output power: 240 W Rated voltage: 32 V, 12 V, 30 V Up to four high-precision power supplies with independent controllable outputs, supporting CH2 and CH3 series and parallel connections Clear graphical interface with waveform and timer display modes 5-digit voltage and current display with minimum resolution of 1 mV, 1 mA Fast output response time: <50us The high current channel support remote voltage compensation sense function. The maximum compensation voltage is 0.6 V Overvoltage protection and overcurrent protection or safe and accurate operation Equipped with a 4.3-inch TFT-LCD display (480 x 272 resolution) USB and LAN standard communication USB-GPIB module is optional Excellent channel density with up to 4 channels in a 3U half rack package Internal data storage for setups and parameters Embedded Web Server with instrument communication that doesn’t require software installation Fully SCPI programming command set support as well as a LabView driver for remote control and system automation Specifications SPD4323X SPD4121X SPD4306X Channel Output CH1: Voltage 0 to 6 V Current 0 to 3.2 ACH2: Voltage 0 to 32 V Current 0 to 3.2 ACH3: Voltage 0 to 32 V Current 0 to 3.2 ACH4: Voltage 0 to 6 V Current 0 to 3.2 A CH1: Voltage 0 to 15 V Current 0 to 1.5 ACH2: Voltage 0 to 12 V Current 0 to 10 ACH3: Voltage 0 to 12 V Current 0 to 10 ACH4: Voltage 0 to 15 V Current 0 to 1.5 A CH1: Voltage 0 to 15 V Current 0 to 1.5 ACH2: Voltage 0 to 30 V Current 0 to 6 ACH3: Voltage 0 to 30 V Current 0 to 6 ACH4: Voltage 0 to 15 V Current 0 to 1 A Resolution 1 mV, 1 mA 1 mV, 1 mA 1 mV, 1 mA Setting Accuracy Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Readback Accuracy Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Display 4.3" TFT-LCD 5-digit voltage and current display 4.3" TFT-LCD 5-digit voltage and current display 4.3" TFT-LCD 5-digit voltage and current display Output power 240 W 285 W 400 W Included 1x Siglent SPD4323X Power Supply 1x Power cord (EU) 1x Output test cord (3 A) 1x USB cable 1x Quick start guide Downloads Datasheet Manual Quick start

Read more less

UNI-T UPO1102CS is a multifunctional, low-cost 2-channel digital phosphor oscilloscope with 100 MHz bandwidth and 1 GSa/s sampling rate. It can be widely used in the fields of electronic and electrical design, debugging, education and industrial design. UPO1000CS series adopts parallel digital signal processing technology, which greatly improves the data processing speed and waveform capture rate. The original Ultra Phosphor technology can present the cumulative effect of the tested signal as a multi-layered afterglow. Compared with traditional digital storage oscilloscopes, the persistence of digital phosphor oscilloscopes can present three-dimensional waveform data of amplitude, time and signal intensity. Fast Acquire technology can accurately capture abnormal events such as video, jitter, noise and runt signals. Specifications UPO1102CS UPO1202CS Bandwidth 100 MHz 200 MHz Analog channels 2 2 Sampling rate 1 GSa/s 1 GSa/s Storage depth 56 Mpts per channel 56 Mpts per channel Rise time ≤3.5ns ≤1.8ns Capture rate 500,000 wfms/s 500,000 wfms/s Waveform record 100,000 frames 100,000 frames Features 7' WVGA (800 x 480) TFT LCD Ultra Phosphor super fluorescent display effect, up to 256 levels of gray display Support RS232, I²C, SPI, CAN and LIN trigger Innovative RS232, I²C, SPI, CAN and LIN hardware decoding Vertical scale: 1 mV/div-20 V/div Low background noise: <100 μVrms 1M points enhanced FFT function. Support frequency setting, waterfall diagram, detection setting and marker measurement etc 36 kinds of waveform parameters can be automatically measured Rich trigger functions (edge, pulse width, video, slope, runt, overshoot, delay, timeout, duration, setup and hold, Nth edge and pattern trigger) Multi-Scopes support dual-channel independent trigger fluorescence display Multi-channel independent 7-bit hardware frequency counter DVM supports dual-channel independent AC and DC true RMS measurement Waveform arithmetic functions (FFT, +, -, ×, ÷, digital filtering, logic operations, and advanced operations) Rich interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail) Support SCPI programmable instrument standard command Support WEB access and control Downloads Datasheet Programming Manual User's Manual Quick Start Guide Software

Read more less

The UPO1104 4-channel digital oscilloscope utilizes Ultra Phosphor 2.0 technology. It features a bandwidth of 100 MHz and a real-time sampling rate of up to 2 GSa/s. It supports an independent DVM module, offers extensive trigger and bus decoding functions, and supports full-memory hardware real-time decoding. The UPO1104 can be widely used in embedded system design, instrumentation, consumer electronics, automotive electronics, field maintenance, education, and many other fields. Features Bandwidth: 100 MHz Channels: 4 Sampling rate: 2 GSa/s Vertical scale: 500μV/div-20 V/div Low-base noise: <100μVrms Maximum storage depth up to 56 Mpts Waveform capture rate of up to 500,000 wfms/s The hardware can be continuous waveform recording 120,000 frames in real time Automatic measurement of 36 waveform parameters, the measurement range divides into screen and cursor area Supports 7 digits hardware frequency meter measurement DVM supports AC/DC TRMS (true virtual value) measurement Waveform calculation function (FFT, add, subtract, multiply, divide, digital filter, logical operation and advanced operation) 1M sampling points to enhance FFT function, it supports frequency setting, waterfall curve, demodulation mode and marker measurement Multiple trigger functions (edge, pulse width, video, slope, runt pulse, over-amplitude pulse, delay, timeout, duration, setup hold, Nth edge and code pattern) Supporting RS232, I²C, SPI trigger Innovative RS232, I²C, SPI full memory hardware for real-time decoding Ultra phosphor display effect, 256 grayscale display 7-inch WVGA (800x480) TFT LCD Multiple interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail, DVM) Supporting waveform navigation, marker and segment Supporting SCPI programmable standard command Support WEB access and control Dimensions: 306 x 138 x 107 mm Weight: 2.45 kg Specifications Model UPO1104 UPO1204 Bandwidth 100 MHz 200 Mhz Analog channels 4 4 Real-time sampling rate 2 GSa/s 2 GSa/s Rise time ≤3.5 ns ≤1.8 ns Storage depth 56 Mpts 56 Mpts Waveform capture rate 500,000 Wfms/s 500,000 Wfms/s Included 1x UNI-T UPO1104 4-ch Phosphor Oscilloscope (100 MHz) 4x Passive probe (100 MHz) 1x Power cord 1x USB cable 1x Manual Downloads Datasheet Software

Read more less

The PeakTech 1240 is a 60 MHz 2-channel digital storage oscilloscope with a high-resolution TFT color display and extensive additional functions. It has a sampling rate of up to 500 MS/s and convinces with its high quality and easy handling with the best price/performance ratio. Features High-resolution TFT color display with 800 x 600 pixels and 65536 colors USB port for real-time data transmission or reading of internal memory Saving of measured values and graphics directly onto the USB-stick VGA-output port for external monitor Autoset and autoscale function for easy operation LAN connection for remote access via network Internal memory of 10 million points per channel or 15 waveforms 20 automatic measurement modes and FFT function PASS/FAIL function Safety: EN 61010-1; CAT II Accessories: 2 pcs. BNC cable, USB cable, software CD for Windows 2000/XP/Vista/7/8/10, power cable, 2 probes, carrying case and manual Specifications Bandwidth 60 MHz Display 20 cm (8”) TFT with 65536 colors Resolution 800 x 600 Pixel Channel 2 CH Sampling mode Normal/peak detect/average Sampling rate each Channel 250 MSa/s Input coupling AC, DC, GND Input impedance 1 MΩ +/- 2 % in parallel with 10 pF +/- 5 pF Input voltage 400 V DC or ACpp Sensitivity 2 mV - 10 V/Skt/div. Rise time < 5,8 ns Accuracy +/- 3 % Vertical resolutions 8 Bits (2 CH simultaneously) Horizontal scale 5ns-100s/Skt./div Sampling range 0,5 - 250 S/s Trigger type Edge/Video/Pulse/Slope Trigger mode Auto, Normal, Single Trigger coupling DC, AC, LF, HF 20 automat. measurements peak-peak, cycle RMS, Vmax, Vmin, Vtop, Vbase, Vamp, overshoot, preshoot, rise time, fall time, +width, -width, +duty, -duty, delay A→B (rising), delay A→B(falling), frequency, period, min, max Phase difference +/- 3° Record length 10.000.000 points/CH Interfaces USB Device 2.0, USB Host 2.0, VGA, LAN Operation voltage 100~240 V ACrms / 50/60 Hz Dimensions 340 x 155 x 70 mm Weight 1.8 kg

Read more less

The PeakTech 6192 is a linear regulated, dual-channel laboratory power supply that delivers reliable performance and enhanced safety, thanks to its integrated safety transformer. With adjustable outputs ranging from 0-60 V and 0-2.5 A DC, it is versatile and well-suited for various laboratory and workshop applications. It features a current preselection function, allowing users to set the desired current before connecting the load. The four-digit blue LED displays clearly and precisely show voltage, current, and power values. The output button ensures that output is only activated after settings have been configured, preventing unintentional changes and increasing operational safety. A temperature-controlled fan automatically responds to the device's internal temperature, providing efficient cooling and quiet operation. The unit is equipped with four potentiometers for quick and precise adjustment of current and voltage values. Additionally, a USB interface enables remote control and data readout via PC. Features Two outputs adjustable from 0-60 V and 0-2.5 A DC Fixed voltage output 5 V/1 A DC With USB interface and PC software 4-digit segment displays for current and voltage Channels can be used independently, in series or in parallel Overload protection and short-circuit proof Temperature-controlled fan High load stability and low residual ripple Sturdy metal housing with carrying handle Output of safety extra-low voltage (SELV) Safety: EN-61010-1, EN 61558-2-6 Specifications Adjustable DC Output voltage 2x 20...60 V Rechargeable DC Output current 2x 0...2.5 A Fixed value output 5 V/1 A USB interface Yes Input voltage 104~127 V AC (60 Hz) or207~253 V AC (50 Hz) switchable Grid stability (at 0-100% load) CV ≤0.01% + 3 mVCC ≤0.2% + 3 mA Load stability (at 0-100% load) CV ≤0.05% + 5 mVCC ≤0.5% + 5 mA Ripple (at 100% load) CV ≤1 mVrmsCC ≤3 mArms Overload protection Constant current limiter circuit and short-circuit proof Accuracy of the voltage display ±0.5% + 5 digits Accuracy of the current display ±0.5% + 5 digits Operating temperature 0°C ... +40°C (<90% RH) Dimensions (W x H x D) 255 x 160 x 335 mm Weight approx. 9 kg Included 1x PeakTech 6192 DC Power Supply 1x Power cable 1x USB cable 1x CD-ROM 1x Manual Downloads Datasheet Interface protocol Software

Read more less

The Siglent SDG1032X Plus is a high-performance dual-channel function/arbitrary waveform generator with a 30 MHz max frequency, 16-bit resolution, and 1 GSa/s sampling rate for superior signal fidelity. It features TrueArb for low-distortion waveforms, EasyPulse for jitter-free pulses, and robust sequence playback. With ±10 V amplitude, a 4.3" display, and versatile modulation, it's a reliable choice for engineers and researchers. Features Dual Channels: Independent output with maximum frequency of 30 MHz High Sampling Rate: 1 GSa/s for precise waveform generation High Vertical Resolution: 16-bit resolution for accurate signal reproduction TrueArb Technology: Generates low-distortion arbitrary waveforms with high fidelity EasyPulse Technology: Produces jitter-free square and pulse signals with fine control over rise/fall times Arbitrary Waveform Length: Supports up to 8 Mpts per channel for complex waveform design Wide Amplitude Range: ±10 V maximum output amplitude Built-in Modulation Functions: AM, FM, PM, PWM, PSK, FSK, ASK, and more Multi-Pulse Output: Enables measurement of power equipment switching parameters PRBS Pattern Generation: Supports up to 40 Mbps for advanced testing needs Sweep and Burst Modes: Flexible test capabilities with adjustable parameters Sequence Playback Function: Stores and plays back complex waveforms efficiently Frequency Counter: Measures frequencies up to 200 MHz with high precision User-Friendly Display: 4.3" color LCD with a clear interface Remote Control Support: Built-in WebServer for control via a web browser Compact Design: Portable and space-saving form factor Specifications Bandwidth 30 MHz Channels 2 Sampling rate 1 GSa/s (4x Interpolation) Vertical resolution 16 bits (per channel) Waveform length 8 Mpts Max. amplitude ±10 V Display 4.3" color TFT LCD (480 x 272) Interfaces USB Host, USB Device, LAN Dimensions 260 x 107 x 296 mm Weight 4.35 kg Included 1x Siglent SDG1032X Plus Arbitrary Function Generator 1x Power Cord 1x USB Cable 1x Guarantee Card 1x Quick Start Guide Downloads Datasheet User Manual Programming Guide Software

Read more less

The Siglent SPD4306X is a 4-channel DC Linear Programmable Power Supply equipped with a 4.3-inch TFT-LCD display, friendly human-machine interface, and excellent performance indicators. Real-time waveform display provides engineers with an informative user interface. SPD4306X offers a total output power of 400 W with a resolution of 1 mV/1 mA. The maximum voltage and current for each channel are as follows: CH1: 15 V/1.5 A CH2: 30 V/6 A CH3: 30 V/6 A CH4: 15 V/1 A Features Rated output power: 400 W Rated voltage: 32 V, 12 V, 30 V Up to four high-precision power supplies with independent controllable outputs, supporting CH2 and CH3 series and parallel connections Clear graphical interface with waveform and timer display modes 5-digit voltage and current display with minimum resolution of 1 mV, 1 mA Fast output response time: <50us The high current channel support remote voltage compensation sense function. The maximum compensation voltage is 0.6 V Overvoltage protection and overcurrent protection or safe and accurate operation Equipped with a 4.3-inch TFT-LCD display (480 x 272 resolution) USB and LAN standard communication USB-GPIB module is optional Excellent channel density with up to 4 channels in a 3U half rack package Internal data storage for setups and parameters Embedded Web Server with instrument communication that doesn’t require software installation Fully SCPI programming command set support as well as a LabView driver for remote control and system automation Specifications SPD4323X SPD4121X SPD4306X Channel Output CH1: Voltage 0 to 6 V Current 0 to 3.2 ACH2: Voltage 0 to 32 V Current 0 to 3.2 ACH3: Voltage 0 to 32 V Current 0 to 3.2 ACH4: Voltage 0 to 6 V Current 0 to 3.2 A CH1: Voltage 0 to 15 V Current 0 to 1.5 ACH2: Voltage 0 to 12 V Current 0 to 10 ACH3: Voltage 0 to 12 V Current 0 to 10 ACH4: Voltage 0 to 15 V Current 0 to 1.5 A CH1: Voltage 0 to 15 V Current 0 to 1.5 ACH2: Voltage 0 to 30 V Current 0 to 6 ACH3: Voltage 0 to 30 V Current 0 to 6 ACH4: Voltage 0 to 15 V Current 0 to 1 A Resolution 1 mV, 1 mA 1 mV, 1 mA 1 mV, 1 mA Setting Accuracy Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Readback Accuracy Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Display 4.3" TFT-LCD 5-digit voltage and current display 4.3" TFT-LCD 5-digit voltage and current display 4.3" TFT-LCD 5-digit voltage and current display Output power 240 W 285 W 400 W Included 1x Siglent SPD4306X Power Supply 1x Power cord (EU) 1x Output test cord (3 A) 1x USB cable 1x Quick start guide Downloads Datasheet Manual Quick start

Read more less

The Siglent SPD4121X is a 4-channel DC Linear Programmable Power Supply equipped with a 4.3-inch TFT-LCD display, friendly human-machine interface, and excellent performance indicators. Real-time waveform display provides engineers with an informative user interface. SPD4121X offers a total output power of 285 W with a resolution of 1 mV/1 mA. The maximum voltage and current for each channel are as follows: CH1: 15 V/1.5 A CH2: 12 V/10 A CH3: 12 V/10 A CH4: 15 V/1.5 A Features Rated output power: 285 W Rated voltage: 32 V, 12 V, 30 V Up to four high-precision power supplies with independent controllable outputs, supporting CH2 and CH3 series and parallel connections Clear graphical interface with waveform and timer display modes 5-digit voltage and current display with minimum resolution of 1 mV, 1 mA Fast output response time: <50us The high current channel support remote voltage compensation sense function. The maximum compensation voltage is 0.6 V Overvoltage protection and overcurrent protection or safe and accurate operation Equipped with a 4.3-inch TFT-LCD display (480 x 272 resolution) USB and LAN standard communication USB-GPIB module is optional Excellent channel density with up to 4 channels in a 3U half rack package Internal data storage for setups and parameters Embedded Web Server with instrument communication that doesn’t require software installation Fully SCPI programming command set support as well as a LabView driver for remote control and system automation Specifications SPD4323X SPD4121X SPD4306X Channel Output CH1: Voltage 0 to 6 V Current 0 to 3.2 ACH2: Voltage 0 to 32 V Current 0 to 3.2 ACH3: Voltage 0 to 32 V Current 0 to 3.2 ACH4: Voltage 0 to 6 V Current 0 to 3.2 A CH1: Voltage 0 to 15 V Current 0 to 1.5 ACH2: Voltage 0 to 12 V Current 0 to 10 ACH3: Voltage 0 to 12 V Current 0 to 10 ACH4: Voltage 0 to 15 V Current 0 to 1.5 A CH1: Voltage 0 to 15 V Current 0 to 1.5 ACH2: Voltage 0 to 30 V Current 0 to 6 ACH3: Voltage 0 to 30 V Current 0 to 6 ACH4: Voltage 0 to 15 V Current 0 to 1 A Resolution 1 mV, 1 mA 1 mV, 1 mA 1 mV, 1 mA Setting Accuracy Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Readback Accuracy Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Voltage: ±(0.03% of reading+10) mV, Current: ±(0.3% of reading+10) mA Display 4.3" TFT-LCD 5-digit voltage and current display 4.3" TFT-LCD 5-digit voltage and current display 4.3" TFT-LCD 5-digit voltage and current display Output power 240 W 285 W 400 W Included 1x Siglent SPD4121X Power Supply 1x Power cord (EU) 1x Output test cord (3 A) 1x USB cable 1x Quick start guide Downloads Datasheet Manual Quick start

Read more less

The PeakTech 5620 is a professional thermal imaging camera with a high thermal resolution of 384x288 thermal image points and a variety of excellent features for work in building thermography or industrial use. In addition to the pure thermal image display, this new development also offers a PIP (picture-in-picture) display, a real image camera or a fusion function in which the contours of the real image recording are combined with the thermal image in order to ensure an even better display. All of the image modes mentioned can also be used for video recording, which also enables audio recordings for the respective video. The many functions are controlled via push buttons on the device, but also via the touch screen function of the color TFT display. All thermal images can be opened and evaluated using the enclosed software, with subsequent changes, e.g. can be done on the pallet selection. Features Professional thermal imaging technology 3.5" touchscreen and graphic menu navigation Thermal image resolution of 384x288 pixels High temperature measuring range up to +550°C High quality thermal image sensor with high temperature sensitivity Fast thermal imaging with 25 Hz Seven color palettes (Iron, Rainbow, White, Black ...) Photo and video recordings with audio commentary WiFi, USB and Bluetooth interfaces IP 54 protected against dust and splash water Accessories: Hard case, 2x Li-Po battery, charger, carrying strap, connection cable, software and instructions Specifications Thermal Resolution 384 x 288 Pixel Temperature Range -20°C … 550°C (-4°F … 1022°F), 0,1° Resolution Accuracy ±2% (±2°C) Display 3.5" Touchscreen TFT Thermal Sensivity <40 mK Field of View (FOV) 37,2°x 28,5° Pixel Pitch 17 µm IFOV 1.7 mrad Wave Length 8 ... 14 µm Emissivity 0.01~1.0 Image Frequency 25 Hz Storage Micro SD (64 GB) Data Interface USB, WiFi, Bluetooth Operation voltage 5000 mAh / 3.7 V Li-Ion Dimensions 100 x 244 x 104 mm Weight approx. 660 g

Read more less

Need a modular, open and hackable test and measurement chassis? The four-channel Envox EEZ Bench Box 3 (BB3) includes includes two DCP405 advanced DC power modules and one DCM224 dual output supplementary DC power module (max. output power 465 W). It is a great solution for product development, debugging, and circuit testing. Features Modular design – use up to three modules in any combination 4.3' TFT color touchscreen display with customizable and responsive GUI Four types of power outputs coupling under firmware control (incl. in series for max. 80 V and parallel for max. 10 A) Max. output power: 465 W Multiple output values views including YT-view for DCP405 modules Programmable lists Tracking mode OVP, OCP, OPP and OTP protection Speed controlled cooling fan SCPI programming via USB or Ethernet MicroPython scripting, Node-RED integration RTC with NTP synchronization MQTT support Easily programmable with 400+ SCPI commands Built-in Ethernet, USB and UART for remote control Build-in removable 8 GB micro SD card for data logging and programming Fast boot, FreeRTOS firmware Quiet operation thanks to multi-sensor fan speed control Software simulator Quick and easy upgrade of the DIB module’s firmware Easy maintenance, disassembling and repair Typical Applications Product development and debugging Laboratories and educational facilities Quality control and assessment Automobile electronic circuit testing Production automation testing Device or circuit characteristic verification and troubleshooting Technical Specifications STM32F769 32-bit ARM Cortex-M7 MCU, 216 MHz, 2 MB Flash, 512 KB SRAM Digital I/O: 2x buffered inputs and 2x buffered outputs (alternative functions: UART, PWM out) Rotary encoder with switch 1x user switch 3x dedicated SPI channels (2x Chip selects per channel), 40-pin IDC connector (DIB v1.0) Battery backup (CR2032 button cell type) USB FS OTG Ethernet PHY (10/100 Mbit/s) 32 KB I²C system EEPROM 8 MB SDRAM 8 GB Micro SD card 4.3' TFT color resistive touchscreen display with brightness control SWG/JTAG connector (optional) Small on-board speaker Four power relays for various power outputs coupling Full range autoswitch AC input (115 / 230 Vac) AC Soft-start (In-rush current limitation) and stand-by AC IEC C14 inlet with two 20 x 5 mm fuse AC power switch AC power input protection and EMI filter Standby LED indicator Ø80 mm DC cooling fan with speed control Kensington lock slot™ Compact size: 290 (W) x 123 (H) x 240 (D) mm Weight (populated with 2x DCP405 and 1x DCM224): 4.05 kg

Read more less

Need a modular, open and hackable test and measurement chassis? The two-channel Envox EEZ Bench Box 3 (BB3) includes two DCP405 advanced DC power modules (max. power 310 W). It is a great solution for product development, debugging, and circuit testing. Features Modular design – use up to three modules in any combination 4.3' TFT color touchscreen display with customizable and responsive GUI Four types of power outputs coupling under firmware control (incl. in series for max. 80 V and parallel for max. 10 A) Max. output power: 310 W Multiple output values views including YT-view for DCP405 modules Programmable lists Tracking mode OVP, OCP, OPP and OTP protection Speed controlled cooling fan SCPI programming via USB or Ethernet MicroPython scripting, Node-RED integration RTC with NTP synchronization MQTT support Easily programmable with 400+ SCPI commands Built-in Ethernet, USB and UART for remote control Build-in removable 8 GB micro SD card for data logging and programming Fast boot, FreeRTOS firmware Quiet operation thanks to multi-sensor fan speed control Software simulator Quick and easy upgrade of the DIB module’s firmware Easy maintenance, disassembling and repair Typical Applications Product development and debugging Laboratories and educational facilities Quality control and assessment Automobile electronic circuit testing Production automation testing Device or circuit characteristic verification and troubleshooting Technical Specifications STM32F769 32-bit ARM Cortex-M7 MCU, 216 MHz, 2 MB Flash, 512 KB SRAM Digital I/O: 2x buffered inputs and 2x buffered outputs (alternative functions: UART, PWM out) Rotary encoder with switch 1x user switch 3x dedicated SPI channels (2x Chip selects per channel), 40-pin IDC connector (DIB v1.0) Battery backup (CR2032 button cell type) USB FS OTG Ethernet PHY (10/100 Mbit/s) 32 KB I²C system EEPROM 8 MB SDRAM 8 GB Micro SD card 4.3' TFT color resistive touchscreen display with brightness control SWG/JTAG connector (optional) Small on-board speaker Four power relays for various power outputs coupling Full range autoswitch AC input (115 / 230 Vac) AC Soft-start (In-rush current limitation) and stand-by AC IEC C14 inlet with two 20 x 5 mm fuse AC power switch AC power input protection and EMI filter Standby LED indicator Ø80 mm DC cooling fan with speed control Kensington lock slot™ Compact size: 290 (W) x 123 (H) x 240 (D) mm Weight (populated with 2x DCP405 and 1x DCM224): 4.05 kg

Read more less

The UPO1204 4-channel digital oscilloscope utilizes Ultra Phosphor 2.0 technology. It features a bandwidth of 200 MHz and a real-time sampling rate of up to 2 GSa/s. It supports an independent DVM module, offers extensive trigger and bus decoding functions, and supports full-memory hardware real-time decoding. The UPO1204 can be widely used in embedded system design, instrumentation, consumer electronics, automotive electronics, field maintenance, education, and many other fields. Features Bandwidth: 200 MHz Channels: 4 Sampling rate: 2 GSa/s Vertical scale: 500μV/div-20 V/div Low-base noise: <100μVrms Maximum storage depth up to 56 Mpts Waveform capture rate of up to 500,000 wfms/s The hardware can be continuous waveform recording 120,000 frames in real time Automatic measurement of 36 waveform parameters, the measurement range divides into screen and cursor area Supports 7 digits hardware frequency meter measurement DVM supports AC/DC TRMS (true virtual value) measurement Waveform calculation function (FFT, add, subtract, multiply, divide, digital filter, logical operation and advanced operation) 1M sampling points to enhance FFT function, it supports frequency setting, waterfall curve, demodulation mode and marker measurement Multiple trigger functions (edge, pulse width, video, slope, runt pulse, over-amplitude pulse, delay, timeout, duration, setup hold, Nth edge and code pattern) Supporting RS232, I²C, SPI trigger Innovative RS232, I²C, SPI full memory hardware for real-time decoding Ultra phosphor display effect, 256 grayscale display 7-inch WVGA (800x480) TFT LCD Multiple interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail, DVM) Supporting waveform navigation, marker and segment Supporting SCPI programmable standard command Support WEB access and control Dimensions: 306 x 138 x 107 mm Weight: 2.45 kg Specifications Model UPO1104 UPO1204 Bandwidth 100 MHz 200 Mhz Analog channels 4 4 Real-time sampling rate 2 GSa/s 2 GSa/s Rise time ≤3.5 ns ≤1.8 ns Storage depth 56 Mpts 56 Mpts Waveform capture rate 500,000 Wfms/s 500,000 Wfms/s Included 1x UNI-T UPO1204 4-ch Phosphor Oscilloscope (200 MHz) 4x Passive probe (200 MHz) 1x Power cord 1x USB cable 1x Manual Downloads Datasheet Software

Read more less

In this lockable universal carrying case you can safely store your sensitive electronic devices while traveling and on the way to work. In order to adapt these sturdy cases universally to the respective equipment, each case is padded with a 1 cm thick foam insert and additionally designed with two 3 cm thick, removable cubic foam inserts, which can be easily adjusted without additional tools. Due to the double notch in the closing edge, these high-quality case offer a high level of safety against the ingress of dust or splash water and are therefore the ideal companion for daily work in the field. Features Integrated lock Stable carrying case for all kinds of work Including cube foam for easy adjustment of the desired shape Changeable cube foam available separately Specifications Material Aluminum Color Black Dimensions 405 x 150 x 330 mm Dimensions (inside) 390 x 130 x 315 mm Payload (max.) 16.2 kg Lock Snap lock (lockable) Cube foam insert Yes Design/Type Aluminum frame/Composite material Downloads Manual

Read more less

The PeakTech 6193 is a linear regulated 2-channel laboratory power supply with 0-30 V/0-5 A DC output. Its integrated safety transformer ensures reliable operation and high safety standards for lab and workshop use. Key features include current preselection for safe setup, four-digit blue LED displays for voltage, current, and power, and an Output On/Off button to prevent accidental changes. The temperature-controlled fan provides efficient and quiet cooling. With four precision potentiometers, output values can be adjusted quickly and accurately. A USB interface enables remote control and data readout via PC, making it ideal for versatile and automated applications. Features Two outputs adjustable from 0-30 V and 0-5 A DC Fixed voltage output 5 V/1 A DC With USB interface and PC software 4-digit segment displays for current and voltage Channels can be used independently, in series or in parallel Overload protection and short-circuit proof Temperature-controlled fan High load stability and low residual ripple Sturdy metal housing with carrying handle Output of safety extra-low voltage (SELV) Specifications Channels 2 Display Type Segment Output Voltage 0-30 V DC Output Current 0-5 A Input voltage 115-230 VAC 50/60 Hz Auxillary output 5 V DC Cooling Active Included 1x PeakTech 6193 DC Power Supply 1x Power cable 1x USB cable 1x CD-ROM 1x Manual Downloads Datasheet Software Interface Protocol

Read more less

The Siglent SDS822X HD digital storage oscilloscope is based on 2 GSa/s, 12-bit Analog-Digital Converters and front ends with excellent noise floor performance. With a 200 MHz bandwidth, and a maximum record length of 100 Mpts, and the capability to analyze 2 analog channels alongside 16 digital channels, the SDS822X HD is perfectly suited for mixed signal analysis. Features 12-bit High Resolution 12-bit Analog-Digital Convertors with sample rate up to 2 GSa/s Front ends with 70 μVrms noise floor @ 200 MHz bandwidth 2/4 analog channels, up to 700 MHz bandwidth SPO technology Waveform capture rate up to 120,000 wfm/s (normal mode), and 500,000 wfm/s (sequence mode) Supports 256-level intensity grading and color temperature display modes. Up to 50 Mpts record length Digital trigger system Intelligent trigger: Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video (HDTV supported), Qualified, Nth edge, Delay, Setup/Hold time. Serial bus triggering and decoder, supports protocols I²C, SPI, UART, CAN, LIN. Segmented acquisition (Sequence) mode, dividing the maximum record length into multiple segments (up to 80,000), according to trigger conditions set by the user, with a very small dead time between segments to capture the qualifying event. History waveform record (History) function, the maximum recorded waveform length is 80,000 frames. Automatic measurements on 50+ parameters, supports statistics with histogram, track, trend, Gating measurement, and measurements on Math, History and Ref. 4 Math traces (2 Mpts FFT, addition, subtraction, multiplication, division, integration, differential, square root, etc.), supports formula editor. Abundant data analysis functions such as Search, Navigate, Counter, Bode plot and Power Analysis High Speed hardware-based Mask Test function, with Mask Editor tool for creating user-defined masks 16 digital channels (optional) 25 MHz waveform generator (optional) 7" TFT-LCD display with 1024 x 600 resolution; Capacitive touch screen supports multi-touch gestures. Interfaces include: USB Hosts, USB Device (USBTMC), LAN (VXI-11/Telnet/Socket), Pass/Fail, Trigger Out Built-in web server supports remote control over the LAN port using a web browser. Supports SCPI remote control commands. Supports external mouse and keyboard. Supports NTP. Specifications Analog Channels 2 Bandwidth 200 MHz Vertical resolution 12-bit Sample rate (Max.) One channel mode: 100 Mpts/chTwo channel mode: Mpts/chFour channel mode: 25 Mpts/ch Memory depth (Max.) One channel mode: 50 Mpts/chTwo channel mode: 25 Mpts/ch Waveform capture rate (Max.) Normal mode: 120,000 wfm/sSequence mode: 500,000 wfm/s Trigger type Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video, Qualified, Nth edge, Delay, Setup/Hold time, Serial Serial trigger and decode (Standard) I²C, SPI, UART, CAN, LIN Measurement 50+ parameters, statistics, histogram, trend, and track supported Math 4 traces 2 Mpts FFT, Filter, +, -, x, ÷, ∫dt, d/dt, √, Identity, Negation, Absolute, Sign, ex, 10x, ln, lg, Interpolation, MaxHold, MinHold, ERES, Average. Supports formula editor Data analysis Search, Navigate, History, Mask Test, Counter, Bode plot, and Power Analysis Digital channel (optional) 16-channel; maximum sample rate up to 1 GSa/s; record length up to 10 Mpts USB AWG module (option) One channel, 25 MHz, sample rate of 125 MHz, wave length of 16 kpts, isolated output I/O 2x USB 2.0 Host, USB 2.0 Device, 10/100 M LAN, Auxiliary output (TRIG OUT, PASS/FAIL), SBUS (Siglent MSO) Probe (Standard) Passive probe PB470 for each channel Display 7 TFT-LCD with capacitive touch screen (1024x600) Included 1x Siglent SDS822X Oscilloscope 2x Passive probe (200 MHz) PP520 1x Power cord (EU) 1x USB cable 1x Certificate of calibration 1x Quick start Downloads Datasheet Manual Programming guide

Read more less

Siglent's SDS2000X Plus series Digital Storage Oscilloscopes are available in bandwidths of 100 MHz, 200 MHz, and 350 MHz, have a maximum sample rate of 2 GSa/s, a maximum record length of 200 Mpts/ch, and up to 4 analog channels + 16 digital channels mixed-signal analysis ability. The SDS2000X Plus series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications that require more than 8-bit resolution. The large 10.1’’ capacitive touch screen supports multi-touch gestures, while the remote web control, mouse and external keyboard support greatly improve the operating efficiency of the SDS2000X Plus. Features 100 MHz, 200 MHz, 350 MHz (upgradable to 500 MHz) models Real-time sampling rate up to 2 GSa/s Record length up to 200 Mpts Serial bus triggering and decoder, supports I²C, SPI, UART, CAN, LIN, CAN FD, FlexRay, I²S and MIL-STD-1553B Provide 10 bit mode, Vertical and Horizontal Zoom Capacitive touch screen supports multi-touch gestures Siglent SDS2000X Plus Oscilloscopes SDS2102X Plus SDS2104X Plus SDS2204X Plus SDS2354X Plus Bandwidth 100 MHz 100 MHz 200 MHz 350 MHz Channels 2 4 4 4 Real-time sampling rate 2 GSa/s 2 GSa/s 2 GSa/s 2 GSa/s Capture rate 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s Memory depth 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch Included Siglent SDS2104X Plus Oscilloscope Passive probes Power cord USB cable Manual Downloads Datasheet Manual Quick guide Manual Firmware

Read more less