This upgraded version 2.0 (available exclusively from Elektor) contains the following improvements: Enhanced protective earthing (PE) for furnace chassis Extra thermal insulation layer around furnace to reduce odors Connection to a computer, allowing curve editing on a PC Features such as constant temperature control and timing functions The infrared IC heater T-962 v2.0 is a microprocessor-controlled reflow oven that you can use for effectively soldering various SMD and BGA components. The whole soldering process can be completed automatically and it is very easy to use. This machine uses a powerful infrared emission and circulation of the hot air flow, so the temperature is being kept very accurate and evenly distributed. A windowed drawer is designed to hold the work-piece, and allows safe soldering techniques and the manipulation of SMDBGA and other small electronic parts mounted on a PCB assembly. The T-962 v2.0 may be used to automatically rework solder to correct bad solder joints, remove/replace bad components and complete small engineering models or prototypes. Features Large infrared soldering area Effective soldering area: 180 x 235 mm; this increases the usage range of this machine drastically and makes it an economical investment. Choice of different soldering cycles Parameters of eight soldering cycles are pre defined and the entire soldering process can completed automatically from Preheat, Soak and Reflow through to cool down. Special heat up and temperature equalization with all designs Uses up to 800 Watts of energy efficient Infrared heating and air circulation to re-flow solder. Ergonomic design, practical and easily operated Good build quality but at the same time light weight and a small footprint allows the T-962 v2.0 to be easily bench positioned transported or stored. Large number of available funtions The T-962 v2.0 can solder most small parts of PCB boards, for example CHIP, SOP, PLCC, QFP, BGA etc. It is the ideal rework solution from single runs to on-demand small batch production. Specifications Soldering area (max) 180 x 235 mm (7.1 x 9.3") Power (max) 800 W Temperature range 0-280°C (32-536°F) Heating method Infrared Processing time 1~8 minutes Power supply 220 V AC/50 Hz Display LCD with Backlight Control mode 8 intelligent temperature curves Dimensions 310 x 290 x 170 mm (12.2 x 11.4 x 6.7") Weight 6.2 kg Included 1x T-962 v2.0 Reflow Soldering Oven (Elektor Version) 1x USB Stick (with Manual and Software) 2x Fuses 1x Power cord (EU) Downloads Manual

Read more less

The Andonstar AD409 microscope is equipped with a 10.1-inch LCD display, giving you a wider viewing range, free your eyes from fatigue. Features 10.1 inch adjustable LCD display Adjustable metal stand & monitor Two metal fixed clips microSD card Capture & Recording Built-in adjustable LEDs HDMI/USB Software supported Specifications Screen size 10.1 inch (25.7 cm) Image sensor 4 MP Video output UHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps) Video format MP4 Magnification Up to 300 times (27 inch HDMI monitor) Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range Min. 5 cm Frame Rate Max. 120fps Video interface HDMI Storage microSD card (up to 32 GB) PC support Windows, PC software with measurement Mobile phone, tablet terminal support Support WiFi connection and measurement Power source 5 V DC Light source 2 LEDs with the stand Stand size 18 x 20 x 30 cm Included 1x Andonstar AD409 Digital Microscope 1x Metal stand with 2 LEDs 1x UV filter (already assembled in the lens) 1x IR remote 1x Switch cable 1x Power adapter 1x HDMI cable 1x Manual Downloads Manual Software Model Comparison AD407 AD407 Pro AD409 AD409 Pro-ES Screen size 7 inch (17.8 cm) 7 inch (17.8 cm) 10.1 inch (25.7 cm) 10.1 inch (25.7 cm) Image sensor 4 MP 4 MP 4 MP 4 MP Video output 2160p 2160p 2160p 2160p Interfaces HDMI HDMI USB, HDMI, WiFi USB, HDMI, WiFi Video format MP4 MP4 MP4 MP4 Magnification Up to 270x Up to 270x Up to 300x Up to 300x Photo resolution Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Photo format JPG JPG JPG JPG Focus distance Min. 5 cm Min. 5 cm Min. 5 cm Min. 5 cm Frame rate Max. 120f/s Max. 120f/s Max. 120f/s Max. 120f/s Storage microSD card microSD card microSD card microSD card PC support No No Windows Windows Mobile connection No No WiFi + Measurement WiFi + Measurement Power source 5 V DC 5 V DC 5 V DC 5 V DC Light source 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand Endoscope No No No Yes Stand size 20 x 12 x 19 cm 20 x 18 x 32 cm 18 x 20 x 30 cm 18 x 20 x 32 cm Weight 1.6 kg 2.1 kg 2.2 kg 2.5 kg

Read more less

Examine your circuits with high precision and solder even the smallest SMDs and elements without any hassle. Features Multifunctional HDMI Digital Microscope features Full HD, comfortable headroom, improved ergonomy, multiple output signals with different resolutions. Tilt angle of the wide LCD monitor is adjustable. Comes with remote control. Can be used as stand-alone. Specifications Screen size 7 inch (17.8 cm) Image sensor 4 MP Video output UHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps) Video format MP4 Magnification Up to 270 times (27 inch HDMI monitor) Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range Min. 5 cm Frame rate Max. 120fps (under 600 Lux Brightness & HDP120) Video interface HDMI Storage microSD card (up to 32 GB) Power source 5 V DC Light source 2 LEDs with the stand Stand size 20 x 12 x 19 cm Included 1x Andonstar AD407 Digital Microscope 1x Metal stand with 2 LEDs 1x Optical bracket 1x UV filter 1x IR remote 1x Switch cable 1x Power adapter 1x HDMI cable 2x Screws 1x Screwdriver 1x User manual Downloads Manual Model Comparison AD407 AD407 Pro AD409 AD409 Pro-ES Screen size 7 inch (17.8 cm) 7 inch (17.8 cm) 10.1 inch (25.7 cm) 10.1 inch (25.7 cm) Image sensor 4 MP 4 MP 4 MP 4 MP Video output 2160p 2160p 2160p 2160p Interfaces HDMI HDMI USB, HDMI, WiFi USB, HDMI, WiFi Video format MP4 MP4 MP4 MP4 Magnification Up to 270x Up to 270x Up to 300x Up to 300x Photo resolution Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Photo format JPG JPG JPG JPG Focus distance Min. 5 cm Min. 5 cm Min. 5 cm Min. 5 cm Frame rate Max. 120f/s Max. 120f/s Max. 120f/s Max. 120f/s Storage microSD card microSD card microSD card microSD card PC support No No Windows Windows Mobile connection No No WiFi + Measurement WiFi + Measurement Power source 5 V DC 5 V DC 5 V DC 5 V DC Light source 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand Endoscope No No No Yes Stand size 20 x 12 x 19 cm 20 x 18 x 32 cm 18 x 20 x 30 cm 18 x 20 x 32 cm Weight 1.6 kg 2.1 kg 2.2 kg 2.5 kg

Read more less

This 2-in-1 hot air soldering station offers a cost-effective solution for soldering and desoldering all types of SMD components. Features Incl. soldering iron and hot air pump. It is suitable for soldering and desoldering all types of surface mounted IC, PCB or components. The control unit has 2 LEDs that display the temperature and in °C and °F. The temperature can be easily adjusted with simple up/down buttoms. The hot air temperature can be calibrated from 3L/min to 24L/min continuously. Temperature is micro-processor controlled and can be adjusted. Temperature range: 50-480°C for soldering iron, 100-500°C for hot air pump. Specifications Power Soldering iron: 24 V, 60 WHot air pump: 300 W Power supply 220-240 V AC/50 Hz Temperature range Soldering iron: 50-480°CHot air pump: 100-500°C Dimensions 113 x 125 x 175 mm Weight 2 kg Included 1x ZD-8922 Rework station 1x Soldering iron 1x Hot air gun 3x Hot air nozzles 1x Soldering iron with needle bit 1x Power cord 1x Soldering iron stand with sponge

Read more less

The Andonstar AD210 is a digital microscope with a large 10.1-inch IPS display that offers a 178° viewing angle and supports 1080P video and 12 MP photo capture. With 260x magnification, the microscope provides a clear view of the sides of components on printed circuit boards. The microscope also comes with a 32 GB memory card and a remote control. 10.1 inch Super IPS Digital Microscope Featuring a large 10.1" IPS display with a 178° viewing angle and support for 1080P video and 12 MP photo capture, this microscope ensures clear and detailed images every time. Explore Coins Like Never Before Experience the enhanced viewing capabilities of the Andonstar AD210 coin microscope. With its upgraded 10.2" working distance metal stand, you can observe both the overall and intricate details of coins, including silver dollars measuring 38.1 mm (1.5 inch). A Must-Have Soldering Microscope for Electronics Repair Conquer various soldering repair scenarios effortlessly with the Andonstar AD210 soldering microscope. It provides more space and durability, making electronics repairs easier than ever. Unlock the World of Extraordinary Magnification Embark on a journey of discovery with our microscope equipped with a biological slide kit and a bottom light stage. Explore the hidden treasures of the microcosmos and marvel at the microscopic world. The Ultimate All-Purpose Digital Microscope With an impressive range of 1 cm to 26 cm adjustable working distance, and a comprehensive set of accessories, including a microscope bottom light stage for observing biological slides, makes it to a variety of purposes, including electronics repairs, coin collecting, and biological slide observation. Its versatile design ensures it meets all your needs. Upgraded Super Strong Stand We have enhanced the traditional Andonstar stand with a larger base and a maximum height of up to 12.6 inches. It offers direct vertical movement and easy height adjustment, making it perfect for coin observation and soldering. Easy Digital Microscope Camera Capture and share your discoveries effortlessly with the included 32 GB memory card and card reader. Take photos/videos and upload them to your computer with ease. Specifications Screen size 10.1 inch (25.7 cm) Image sensor 2 MP Video output FHD 1920x1080 (30fps)1080p 1440x1080 (30fps)HD 1280x720 (30fps) Video format AVI Magnification Up to 260 times Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range Min. 2 cm Frame Rate Max. 30fps Storage microSD card (up to 32 GB) Power source 5 V DC (via USB) Light source 2 LEDs with the stand Stand size 18 x 20 x 32 cm Included 1x Andonstar AD210 digital microscope 1x Metal stand with 2 LEDs 1x Microscope bottom light stage 1x Column 2x Metal clips 5x Slides 1x Card reader 1x 32 GB memory card 1x Remote control 1x USB power adapter (EU) 1x USB power cable 1x Wiping cloth 1x Manual Downloads Manual

Read more less

With these jumper wires (length: 20 cm) you can connect a Raspberry Pi or an Arduino with breadboards. Each cable consists of 40 individual wires/pins which can also be separated. Included 1x 40-pins female to female 1x 40-pins male to male 1x 40-pins male to female

Read more less

The perfect tool for quick repairs The FNIRSI HS-01 is a powerful, adjustable smart soldering iron with a built-in 0.87-inch OLED display that quickly reaches temperatures between 80-420°C (180-780°F). The display shows all important information, including the status of the temperature level, the set temperature, the supply voltage and the power percentage. You can set the input voltage from 9-20 V directly in the menu according to your needs. The integrated sleep mode automatically turns off the iron after 30 minutes. Features 96 W input (DC) 65 W PD power OLED display Constant temperature & fast heating CNC metal integral molding Smart safety anti-scald Mini pocket size Ergonomic design Aluminum material Left/right hand switch Efficient heat radiation Inductive sleep Color: Black Specifications Power 65 W Screen 0.87" OLED Operating voltage 9-20 VDC Power supply USB-C Temperature range 80-420°C (180-780°F) Fast charging protocol PD trigger Dimensions 184 x 20 x 20 mm (7.24 x 0.79 x 0.79') Weight 56 g Power Selection Operating voltage 20 V 15 V 12 V 9 V Operating current ≥3.25 A ≥2.5 A ≥2 A ≥1.5 A Power 65 W 37.5 W 24 W 13.5 W Tin melting time 8s 12s 17s 30s Included 1x FNRISI HS-01 smart soldering iron 6x Soldering iron tips (HS01-BC2, HS01-KR, HS01-K65, HS01-B2, HS01-ILS, HS01-BC3) 1x DC to USB-C power cable 1x Mini soldering iron stand 1x Manual Required Power adapter USB-C cable Downloads Manual Firmware V0.3.s19

Read more less

Fumes released during the soldering process are potentially harmful to health. This solder fume extractor is securely fastened to the work table with a bracket. Thanks to the 3 axes, the solder fume extractor can be positioned perfectly, i.e. directly above the rising solder fumes. The harmful solder fumes are extracted by a powerful but quiet fan and filtered by an activated-carbon filter mat. Features Removes solder fumes Absorbs toxic gases and fumes from brazing operations Helps reduce the likelihood of headaches, eye irration and neusea Adjustable absorption angle for accurate placement Easy replaceable activated carbon filter High-performance fan Low noise and long life service Specifications Absorption capacity: 1 m³/min (max.) Power consumption: 23 W Power supply: 220-240 VAC Amount of activated carbon filter: 7 g Maximum absorption weight: 2 g Dimensions: 220 x 270 x 168 mm (W x H x D) Weight: 1.4 kg

Read more less

This temperature-controlled digital soldering station with adjustable temperature range from 160°C to 480°C is an affordable and reliable tool for all kinds of soldering work in the (home) laboratory. Thanks to the high-quality coated heating element, the desired soldering temperature (Celsius or Fahrenheit) is quickly reached and shown on the LED display. Features A temperature controlled soldering station with adjustable temperature range from 160°C to 480°C (320°F to 896°F). A two-line LED readout simultaneously displays temperature setting and actual temperature. Gloss finish pleasing to the eye. Compact and lightweight soldering iron with silicone cord. A user-friendly soldering iron handle with a foam sleeve. Easier way to achieve °C/°F conversion with the asterisk button. Specifications Power 25 W (max. 50 W) Display LED Temperature 160°C to 480°C (320°F to 896°F) Temperature deviation ±5% Grounded Yes Heating rate Melt solder within 20s Withstand voltage 1500/1MA Input voltage AC 220-240 V (50 Hz) Output voltage 24 V Included ZD-8961-A Soldering station Solderin iron stand Soldering iron with soldering tip N8-1 Cleaning sponge Cleaning ball Power cord (EU)

Read more less

This silicone soldering mat can be used as a base for all kinds of soldering work such as assembly or repair. Specifications Withstands 200-230°C constantly and 480-500°C for short periods Ideal for soldering electronics components or repairing PCBs, smartphones, etc. Color: Green Dimensions: 209 x 295 mm

Read more less

This set contains 4 soldering tips for the temperature-controlled digital soldering station ZD-8961-A. Included 1x Soldering tip N8-1 1x Soldering tip N8-2 1x Soldering tip N8-3 1x Soldering tip N8-4

Read more less

This 145-in-1 screwdriver set is a versatile tool for precise repairs on devices such as cell phones, watches, household appliances and computers. It contains 132 magnetic screwdriver bits made from high-quality chrome vanadium steel. In addition, the set contains 13 disassembly tools such as a 130 mm extension bar, a suction cup, a spudger, a stainless steel tweezers and ultra-thin opening tools. This set is suitable for both DIY enthusiasts and professionals who need to carry out a wide range of repairs. Included S-2 45mm deep hole screwdriver bits Flat-head (Slotted): 1.5 2.0 Phillips: 1.5 2.0 CR-V sockets Hex socket: M2.5*2 M3.0 M3.5 M4.0 M4.5 M5.0 M5.5 G3.8 G4.5 PH2 U CR-V bits Hex: H0.7 H0.9 H1.3 H1.5 H2.0 H2.5 H3.0 H3.5 H4.0 H4.5 H5.0 H6.0 Phillips: 1.0*2 1.5*3 2.0*2 2.5*2 3.0*3 3.5*2 JIS000 JIS00 JIS0 JIS1 Torx: T1*3 T2*3 T3*2 T4*2 T5 T6 T7 T8 T9 T10 T15 T20 Flat-head (Slotted): 1.0*2 1.3*2 1.5*2 2.0*2 2.5*2 3.0*2 3.5*2 4.0*2 Torx Security: T6H T7H T8H T9H T10H T15H T20H Pozidriv: PZ00*2 PZ0*2 PZ1*2 PZ2*2 Tri-wing: Y0.8*3 Y2.0*2 Y2.5*2 Y3.0*2 Pentagon: 0.8*3 1.2*3 1.5*3 2.0*2 U-shaped: U2.0*2 U2.6*2 U3.0*2 Triangle: 2.0 2.3 2.6 3.0 Square: SQ0 SQ1 SQ2 SIM ejector: SIM0.8 SIM1.0 Stand off: 1.5*2 2x Spudger 1x Suction cup 5x Ultra-thin opening tools 1x Tweezer 1x Extension bar 1x Handle

Read more less

This PCB holder is ideal for any application where a third or fourth hand and a magnifying lamp are needed. Features The helping hands with 4 adjustable gooseneck arms. LED magnifying lamp with USB-C interface. Metal base with non-slip rubber strips. Comes with a cleaning ball, a sponge, a solder wire stand and rosin. Specifications Length of gooseneck arms: 270 mm LED magnifying lamp with 5-diopter lens Power supply via USB Dimensions (stand): 185 x 175 x 20 mm Weight: 620 g

Read more less

This Rework Station Bundle, consisting of the ZD-8968 Hot Air Rework Station and the ZD-11P PCB holder, offers precise temperature control, adjustable airflow, and a stable hold for your circuit board. The ZD-8968 Hot Air Rework Station is a high-performance device designed for precision desoldering and rework tasks with SMD components. It features a wide temperature range of 100-500°C (212-932°F), with adjustable air and temperature control, a clear LED display, and an automatic sleep mode for enhanced safety and efficiency. The ZD-11P PCB Holder is equipped with 5 adjustable 360° rotatable goosenecks (4 with alligator clips, 1 with flashlight holder + flashlight), providing additional flexibility and stability. It securely holds the PCB in place, making the handling of SMD components easier and more precise. Features 300 W heating power ensures quick heat-up Wide temperature range 100-500°C (212-932°F) allows precise control Closed-loop sensor and MCU zero-crossing design ensure accurate and stable temperature regulation. The hot air pump handle includes a built-in sensor that switches to Working Mode when picked up and to Standby Mode when placed back in the holder. Automatic standby mode activates after 10 minutes of inactivity. Automatic cooling system and deferred power-off function protect the heating element. Brushless motor fan provides quiet operation, smooth airflow, and an extended lifespan. High-quality heating element doubles working efficiency and saves energy. LED digital display for clear monitoring of temperature settings. Simple buttons for adjusting air volume and temperature. Switching between °C and °F Heat-resistant stand with hot air gun holder, 5 flexible adjustable arms with alligator clips and a flashlight (AA battery not included) Specifications ZD-8968 Hot Air Rework Station Power 300 W Temperature range 100-500°C (212-932°F) Power supply 220-240 V AC/50 Hz Weight 1.2 kg ZD-11P PCB Holder Base (Dimensions) 210 x 134 mm Metal rod (Height) 250 mm Included Base, metal rod, 4 gooseneck arms with alligator clips, 1 gooseneck arm with flashlight holder Included 1x ZD-8968 Hot Air Rework Station 1x ZD-11P PCB Holder (stand with soldering iron holder with 5 adjustable arms, 4 with alligator clips and 1 with flashlight holder) 1x Flashlight (AA battery not included) 3x Hot air nozzles (79-7911, 79-7912, 79-7913) 1x Power cord (EU) 1x Power cord (UK) 1x Manual

Read more less

With the PCW08G 9-piece tweezer set, you are well equipped to perform precision work on sensitive electronic components. The tweezers are made of coated stainless steel and are therefore particularly durable and resistant. The set is antistatic and ESD-safe, which means that the tweezers are ideal for working with electronic components, as they prevent electrostatic charges, thus avoiding damage to the components. With the set you get a storage bag, enabling you to safely store and transport your tweezers. So you always have everything ready to hand when you need it. Thanks to the different shapes and tip types of the tweezers, the set is ideal for a variety of applications, such as model making, jewelry making and watch repair. Even the smallest components can be easily gripped and positioned. Included ESD-10, straight tip ESD-11, straight tip ESD-12, straight tip ESD-14, straight tip ESD-16, straight tip ESD-13, flat round head ESD-15, 45° curved tip ESD-17, 30° curved tip ESD34A-sa, flat head Storage bag

Read more less