Raspberry Pi Displays

33 products


  • HyperPixel 4.0 – Hi-Res Display for Raspberry Pi (Touch Version)

    Pimoroni HyperPixel 4.0 - Hi-Res Display for Raspberry Pi (Touch Version)

    HyperPixel 4.0 is the perfect way to use your RPi without a bunch of cables or a bulky display. Design your own interface to control your project, display data, or turn your Pi into a tiny media centre. This version of HyperPixel has a gorgeous IPS display, with wide viewing angles, custom-made cover glass, and the alternate I²C interface is broken out for advanced users. Features High-speed DPI interface 4.0' IPS (wide viewing angle, 160°) display (86.4 x 51.8 mm) 800x480 pixels (~235 PPI) 18-bit colour (262,144 colors) 60 FPS frame rate Contrast ratio: 500:1 Capacitive touch 40-pin female header included to boost height for Raspberry Pi B+, 2, 3, 3B+ and 4 Standoffs included to securely attach to your RPi Compatible with all 40-pin header Raspberry Pi models One-line installer Dimensions: 58.5 x 97 x 12 mm (WxHxD, depth includes header and display) HyperPixel uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays use. It has a 60 FPS frame rate and a resolution of approximately 235 pixels per inch (800x480) on its 4.0' display. The display can show 18-bits of colour (262,144 colors). This Touch version has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch! Everything comes fully-assembled, and there's no soldering required! The display is securely stuck down to the HyperPixel 4.0 PCB and connected via a neat little flush-mounting FPC cable. Just pop HyperPixel 4.0 on your RPi and run our installer to get everything set up! Please note: when installing HyperPixel 4.0 onto your RPi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel. It'll work with any 40-pin version of the RPi, including RPi Zero and RPi Zero W. If you're using it with a larger RPi then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Zero or Zero W then just pop it straight onto the GPIO. The included standoff kit allows you to mount your HyperPixel 4.0 safely and securely to your RPi. Just screw them into the posts on the underside of the HyperPixel 4.0 PCB and then secure with screws through the mounting holes on your RPi. Downloads GitHub

    € 79,95

    Members € 71,96

  • Waveshare 4-digit 8-segment Display Module for Raspberry Pi Pico

    Waveshare Waveshare 4-digit 8-segment Display Module for Raspberry Pi Pico

    Features SPI-compatible, easy to drive Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Digits 4 Dispaly size 0.4 inch LED color red Driver 74HC595 Display part no. FJ4401AH Dimensions 52 × 21 mm

    € 9,95

    Members € 8,96

  •  -46% Case for 7` RGB-Touch-Display for Raspberry Pi

    JOY-iT Case for 7" RGB-Touch-Display for Raspberry Pi

    Case for 7' RGB-Touch-Display for Raspberry Pi

    € 12,95€ 6,95

    Members identical

  • "Waveshare 3.5\" Touch Display Module for Raspberry Pi Pico (480x320)"

    Waveshare Waveshare 3.5" Touch Display Module for Raspberry Pi Pico (480x320)

    Features 480 x 320 resolution, IPS screen, 65K colors, clear and colorful displaying effect Dedicated touch controller, bringing more smooth touching effect than AD-controlled solutions MicroSD card slot for storing images and direct displaying them easily Programmable backlight control, power saving Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Resolution 480 x 320 pixels Communication interface SPI Display size 73.44 x 48.96 mm Display panel IPS Pixel size 0.153 x 0.153 mm Driver ILI9488 Dimensions 86.00 x 57.20 mm Touch controller XPT2046 Downloads Wiki

    € 29,95

    Members € 26,96

  • Pimoroni Raspberry Pi Pico Display Pack

    Pimoroni Pimoroni Raspberry Pi Pico Display Pack

    Pico Display lets you turn a Pico into a compact user interface device for a bigger project, capable of giving instructions, displaying readouts and even incorporating elaborate nested menus. If you'd rather use your Pico as a standalone device you could make a little rotating slideshow of images, display beautiful graphs from sensor data or build your own Tamagotchi or matchbox sized text adventure game.Features 1.14” 240x135 pixel IPS LCD screen 4 x tactile buttons RGB LED Pre-soldered female headers for attaching to Pico Compatible with Raspberry Pi Pico. Fully assembled No soldering required (as long as your Pico has header pins attached). Dimensions: approx 53 x 25 x 9 mm (L x W x H) Screen usable area: approx 25 x 15 mm (L x W) C/C++ and MicroPython libraries

    € 19,95

    Members € 17,96

  • HyperPixel 2.1 Round – Hi-Res Display for Raspberry Pi

    Pimoroni HyperPixel 2.1 Round - Hi-Res Display for Raspberry Pi

    HyperPixel 2.1 Round has all the great features of other HyperPixels – crisp, brilliant IPS display touchscreen, and high-speed DPI interface – it's just rounder! You can use it with any Raspberry Pi with a 40-pin header but it works particularly nicely with the RPi Zero footprint – it's designed so you can mount a Zero neatly behind it, so you can't see the RPi when you look at it from the front.This version of HyperPixel would be great for custom interfaces and control panels – mounted on a wall it would make a really neat, minimalist smart home controller or a stylish 'what's playing' display for your sound system. Everything is pre-soldered and ready to go, just pop it onto your RPi, install the software, and away you go!HyperPixel 2.1 Round uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 229 pixels per inch (480x480px) on its 2.1' display. The display can show 18-bits of colour (262,144 colors).Features High-speed DPI interface 2.1' IPS (wide viewing angle, 175°) display 480x480 pixels, minus the corners (~229 PPI) 18-bit colour (262,144 colors) 60 FPS frame rate Active area: 53.28 x 53.28 mm Capacitive touchscreen (with Python library) Compatible with all 40-pin header Raspberry Pi models Dimensions: 71.80 x 71.80 x 10.8 mm (WxHxD, depth includes header and display). With a RPi Zero attached with short standoffs, the total depth is 17 mm. Downloads Display library for Raspberry Pi OS Python touchscreen library Dimensional drawing Pinout

    € 79,95

    Members € 71,96

  • HyperPixel 4.0 Square Touch – Hi-Res Display for Raspberry Pi

    Pimoroni HyperPixel 4.0 Square Touch - Hi-Res Display for Raspberry Pi

    HyperPixel 4.0 Square has all the great features of our standard HyperPixel 4.0 – a crisp, brilliant IPS display with touchscreen, and high-speed DPI interface – it's just more square!This square version of HyperPixel 4.0 is great for custom interfaces and control panels, and works really well for Pico-8 games. Everything is pre-soldered and ready to go, just pop it onto your RPi, run our installer, and away you go!Features High-speed DPI interface 4.0' IPS (wide viewing angle, 160°) display (72x72 mm) 720x720 pixels (~254 PPI) 18-bit colour (262,144 colors) 60 FPS frame rate Optional capacitive touchscreen 40-pin female header included to boost height for Raspberry Pi B+, 2, 3, 3B+ and 4 Standoffs included to securely attach to your RPi Compatible with all 40-pin header Raspberry Pi models One-line installer HyperPixel 4.0 Square uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small RPi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 254 pixels per inch (720x720px) on its 4.0' display. The display can show 18-bits of colour (262,144 colors).This Touch version has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch!Please note: when installing HyperPixel 4.0 Square onto your RPi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel.It'll work with any 40-pin version of the RPi, including RPi Zero and RPi Zero W. If you're using it with a larger RPi then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Zero or Zero W then just pop it straight onto the GPIO.The included standoff kit allows you to mount your HyperPixel 4.0 Square safely and securely to your RPi. Just screw them into the posts on the underside of the HyperPixel 4.0 Square PCB and then secure with screws through the mounting holes on your RPi.DownloadsGitHub

    € 79,95

    Members € 71,96

  • Waveshare 5.65` ACeP 7-Color E-Paper E-Ink Display Module (600x448)

    Waveshare Waveshare 5.65" ACeP 7-Color E-Paper E-Ink Display Module (600x448)

    Features Advanced Color ePaper (ACeP) technology, supports 7-color display No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc. Onboard voltage translator, compatible with 3.3/5 V MCUs Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32) Specifications Operating voltage 3.3/5 V Display color ACeP 7-Color Interface 3-wire SPI, 4-wire SPI Grey scale 2 Outline dimensions 138.5 x 100.5 mm Full refresh time <35s Display size 114.9 x 85.8 mm Refresh power 50 mW (typ.) Dot pitch 0.1915 x 0.1915 mm Standby time <0.01 uA (almost none) Resolution 600 x 448 pixels Viewing angle >170° Downloads Wiki

    € 69,95

    Members € 62,96

  • Pimoroni Badger 2040

    Pimoroni Pimoroni Badger 2040

    Badger 2040 is a hackable, programmable badge with E Ink display, powered by Raspberry Pi RP2040.The Badger 2040 is equipped with plenty of buttons so you can easily change what's displayed on the screen, a slot so you can clip it onto a lanyard and a battery connector so you can keep things portable and refresh the screen whilst on the go.Here are some things you could do with it! Switch between images, pronouns or secret identities at the push of a button Make yourself into a mobile weather station or air quality monitor (by adding a sensor breakout) Store important QR codes for getting into places (or to Rickroll people) Make a tiny to-do list and tick stuff off Display inspirational badger quotes or educational badger facts of the day Want to show your Badger the world? We've put together a convenient Badger + Accessory Kit which contains batteries, a lanyard and everything else that's needed to get portabello.Features 2.9' black and white E Ink display (296 x 128 pixels) Ultra wide viewing angles Ultra low power consumption Dot pitch – 0.227 x 0.226 mm Powered by RP2040 (Dual Arm Cortex M0+ running at up to 133 Mhz with 264 kB of SRAM) 2 MB of QSPI flash supporting XiP Five front user buttons Reset and boot buttons (the boot button can also be used as a user button) White LED USB-C connector for power and programming JST-PH connector for attaching a battery (input range 2.7-6 V) High-precision voltage reference for battery level monitoring Qw/ST (Qwiic/STEMMA QT) connector Fully-assembled (no soldering required) Schematic Mechanical drawing C++/MicroPython libraries SoftwareBecause it's a RP2040 board, Badger 2040 is firmware agnostic! You can program it with C/C++, MicroPython or CircuitPython.C++/MicroPython libraries contain some nifty software tweaks to let you get the most out of your Badger. You'll get best performance using C++, but if you're a beginner we'd recommend using our batteries included MicroPython build for ease of getting started. Download Pirate brand MicroPython (special Badger edition) Getting Started with Badger 2040 C++ examples MicroPython examples MicroPython function reference You can also use CircuitPython on your Badger 2040. CircuitPython drivers are designed to work on a bunch of different microcontrollers so you won't get the fancy RP2040-architecture specific tweaks that you'll find in the library, but you will get access to all the nice conveniences of Adafruit's ecosystem. Download CircuitPython for Badger 2040 Getting Started with CircuitPython CircuitPython examples BadgerOS ported to CircuitPython by Stephane BeBoX

    € 24,95

    Members € 22,46

  • "Waveshare 2.13\" Touch E-Paper E-Ink Display for Raspberry Pi Zero (incl. Case)"

    Waveshare Waveshare 2.13" Touch E-Paper E-Ink Display for Raspberry Pi Zero (incl. Case)

    Features 2.13' capacitive touch e-Paper display, 5-point touch, 250×122 pixels Supports waken up by user-defined gesture No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi Zero / Zero W Comes with development resources and manual (examples for Raspberry Pi) Included 1x 2.13inch Touch e-Paper HAT 1x ABS case 1x Screwdriver 1x Thermal tape 1x Rubber feet 4pcs 2x Screws Downloads Documentation

    € 34,95

    Members € 31,46

  • JOY-iT Raspberry Pi Controllerboard for RGB-LED Matrix

    JOY-iT JOY-iT Raspberry Pi Controllerboard for RGB-LED Matrix

    FUNCTION Logic level converter from 3.3 V to 5V for controlling of up to 3 LED matrix rows PASSIVE AND ACTIVE COOLING Aluminium heatsink with a 25x25mm sized fan COMPATIBLE WITH Raspberry Pi 3A/B/A+/B+, 4B INPUT VOLTAGE 5 Volt INTERFACES 3x HUB75 plugs DATA LINE E SWITCHABLE with jumpers to Pin 4 or 8 DIMENSIONS 65 x 56 x 26 mm WEIGHT 40 g ITEMS SHIPPED Controller, heatsink, fan, 2 spacers, 6 screws and nuts, 4 flat washers, 2 jumpers EAN 4250236819631 ARTICLE NO. RB-MatrixCtrl

    € 15,95

    Members € 14,36

  • Pimoroni Display HAT Mini for Raspberry Pi Zero

    Pimoroni Pimoroni Display HAT Mini for Raspberry Pi Zero

    Display HAT Mini features a bright 18-bit capable 320x240 pixel display with vibrant colours and formidable IPS viewing angles, connected via SPI. It's got four tactile buttons for interacting with your Raspberry Pi with your digits and a RGB LED for notifications. A QwST connector (Qwiic / STEMMA QT) and a Breakout Garden header is also squeezed in so it's a doddle to connect up different kinds of breakouts. It will work with any model of Raspberry Pi with a 40 pin header, but we think it goes with the Raspberry Pi Zero particularly well - we've included a pair of standoffs so you can use to bolt HAT and Raspberry Pi together to make a sturdy little unit. To accommodate the screen Display HAT Mini is a bit bigger than a standard mini HAT or pHAT – it's around 5 mm taller than a Raspberry Pi Zero (so a Mini HAT XL or a Mini HAT Pro, if you will). Display HAT Mini lets you turn a Raspberry Pi into a convenient IoT control panel, a tiny photo frame, digital art display or gif-box, or a desktop display for news headlines, tweets, or other info from online APIs. This screen is a handy 3:2 ratio, useful for retro gaming purposes! Features 2.0” 320x240 pixel IPS LCD screen, connected via SPI (~220 PPI, 65K colours) 4x tactile buttons RGB LED Qw/ST (Qwiic/STEMMA QT) connector Breakout Garden / I²C header Pre-soldered socket header for attaching to Raspberry Pi Compatible with all models of Raspberry Pi with a 40-pin header. Fully assembled No soldering required (as long as your RPi has header pins attached). Dimensions: approx 65.5 x 35 x 9 mm (W x H x D, includes header and display). With a Raspberry Pi Zero attached with standoffs, the total depth is 17 mm. Screen usable area: 40.8 x 30.6 mm (L x W) Pinout Schematic Dimensional drawing Display HAT Mini Python library ST7789 Python library Included Display HAT Mini 2x 10 mm standoffs

    € 32,95

    Members € 29,66

  • Last stock! Joy-Pi Note – 11,6` Raspberry Pi 4-gebaseerde Notebook

    JOY-iT Joy-Pi Note - 11.6” Raspberry Pi 4-based Notebook

    1 in stock

    3-in-1 Solution: Notebook, Learning Platform and Experiment Center The Joy-Pi Note is the new flagship in the Joy-Pi family. With its 11.6' IPS screen and a detachable, wireless keyboard, it takes the Joy-Pi‘s basic concept in a new, high-quality and attractive format. With 46 courses and 18 projects, the Joy-Pi Note is not only suitable as an experiment center, but is also ideal for use in the education sector. With over 22 integrated sensors and modules, there are no limits to the user‘s own joy of experimentation. This simplifies the introduction to electrical engineering and programming. Due to the installed learning platform, which was developed especially for the Joy-Pi Note, the installed units can be operated and learned independently of one‘s own previous knowledge. It is also possible to connect additional sensors and modules via the pins of the Raspberry Pi, which are routed to the outside, and thus also carry out more complex projects. Of course, the Joy-Pi Note can also be used as a „classic“ notebook. All programs compatible with the Raspberry Pi 4 can be installed. The integrated 2 MP camera also makes video conferencing possible, for example. All Raspberry Pi 4 models can be used (we recommend 4 GB RAM or higher). On the bottom of the device, you will find a compartment where you can insert a power bank to also operate the Joy-Pi Note mobile. Specifications Main Features Screen 11.6' 1920x1080 IPS LCD Camera 2 MP Special features Fully equipped set, completely integrated experiment center, pre-installed learning platform, detachable wireless keyboard, integrated compartment for powerbank & accessories Lessons of the learning platform 46 courses & 18 projects for Python and Scratch Power supply 12 V hollow plug, 5 V USB Compatible to Raspberry Pi 4 (4 GB and 8 GB RAM) Keyboard layouts DE (default) + US, UK, FR, IT, PT and Nordic Dimensions 291 x 190 x 46 mm Weight 1.3 kg Included sensors, modules & accessories Display 7-segment display, 16x2 LCD module, 8x8 RGB Matrix Sensors DHT11 temperature & humidity sensor, tilt sensor, motion sensor, sound sensor, touch sensor, RFID module, light sensor, ultrasonic distance sensor Motors Servo interface, stepper motor interface, vibration motor Control Joystick, 4x4 button matrix, Raspberry Pi & PCB connection switch, motion sensor, sensitivity controller, sound sensor sensitivity controller, 16x2 LCD module brightness controller Others Relay, fan, GPIO extension, GPIO LED indicator, breadboard, IO/ADC/I²C/UART expansion interface, infrared sensor interface, buzzer, display driver Accessories RFID chip, RFID card, 12 V power supply, servo motor, stepper motor, infrared receiver, infrared remote control, DC motor with fan attachment, HDMI connector, screwdriver, microSD card (32 GB), SD card reader, electronic accessories, wireless mouse, wireless keyboard Included Joy-Pi Note Accessories Quick guide Required Raspberry Pi 4 (4 GB or 8 GB RAM)

    1 in stock

    € 399,00

    Members € 359,10

  • "Waveshare 2.66\" E-Paper E-Ink Display Module for Raspberry Pi Pico (296x152)"

    Waveshare Waveshare 2.66" E-Paper E-Ink Display Module for Raspberry Pi Pico (296x152)

    Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal IO pins Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color red, black, white Interface 3-wire SPI, 4-wire SPI Grey scale 2 Outline dimensions 74.00 × 37.5 0mm Full refresh time 15s Display size 60.088 × 30.704 mm Refresh power 42.4 mW (typ.) Dot pitch 0.203 × 0.202 mm Standby current <0.01 uA (almost none) Resolution 296×152 pixels Viewing angle >170° Downloads Wiki

    € 27,95

    Members € 25,16

  • JOY-iT 3.5' Touchscreen for Raspberry Pi

    JOY-iT JOY-iT 3.5" Touchscreen for Raspberry Pi

    With the 3.5 inch large TFT touch screen display, you can build a mini tablet PC based on a Raspberry Pi. The display, with a maximum resolution of 480x320 pixels, is simply plugged into the existing GPIO connectors. Specifications Display: 3.5' (8.89 cm) Resolution: 480x320 pixels Touchscreen Type: Resistive Touch screen controller: XPT2046 Colors: 65536 Backlight: LED Connection: GPIO header Aspect ratio: 8:5 Display Size: 85 x 56 mm

    € 34,95

    Members € 31,46

  • Waveshare 2.23` OLED Display Module for Raspberry Pi Pico (128x32)

    Waveshare Waveshare 2.23" OLED Display Module for Raspberry Pi Pico (128x32)

    Features Adopts both 4-wire SPI and I²C interface, better compatibility, fast data rate Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Logical voltage 3.3 V Viewing angle >160° Operating voltage 3.3 V/5 V Resolution 128×32 pixels Communication interface 4-wire SPI, I²C Display size 55.02 × 13.10 mm Display panel OLED Pixel size 0.41 × 0.39 mm Driver SSD1305 Dimensions 63.00 × 26.00 mm

    € 19,95

    Members € 17,96

  • JOY-iT 64x64 RGB-LED Matrix Module

    JOY-iT JOY-iT 64x64 RGB-LED Matrix Module

    Display RGB-LED Resolution 64 x 64 Amount of LED 4096 LEDs LED Size 3 mm Pitch Supply Voltage 5 V Max. Power Input 40 W Control 1/32 Scan Operating Temperature -20 °C - 55 °C Viewing Angle 140° Pixel Density 111111 Pixel / m² Dimensions 192 mm x 192 mm x 14 mm Weight 246 g Items Shipped LED-Matrix, Kabel For more information, check out the user manual here.

    € 59,95

    Members € 53,96

  • Raspberry Pi 7” Touchscreen Display

    Raspberry Pi Foundation Official 7" Touchscreen for Raspberry Pi

    1 review

    Out of stock

    The 800 x 480 7' Touch Display features a full color display connects through an adapter board that is included in the kit. All necessary drivers to support the 10-finger capacitive touch features as well as an on-screen keyboard are integrated into the latest Raspbian OS to work completely free of keyboard or mouse. What's in the box:• 7” Official RPi Touch Display• The Adapter Board• A DSI Flexcable• Four stand-offs and screws (for mounting the adapter board and RPi board to the display)• Four jumper wires (for connecting the power from the Adapter Board and the GPIO pins on the RPi powering both units) Screen specifications:• 7” Touch Display• Dimensions: 194 x 110 x 20 mm• Actual screensize: 155 x 86 mm• Resolution: 800 x 480 px• 10 finger capacitive touch This display will work with:• Raspberry Pi Model A+• Raspberry Pi 1 Model B+• Raspberry Pi 2 Model B• Raspberry Pi 3 Model B• Raspberry Pi 3 Model B+ Although future software updates are expected to enable the display to be used on a Model B or A. Please note that the position of the mounting spaces on the screen will not support these older models. Read more about this by following the link:www.elektormagazine.com/news/the-pi-gets-an-official-touchscreen

    Out of stock

    € 82,95

    Members € 74,66

  • JOY-iT 84x48 LCD Display

    JOY-iT JOY-iT 84x48 LCD Display

    This display correspond to the Nokia 5110 norm which makes it perfectly to display data or graphs of measured values on a microcontroller or a single-board computer. Additionally, the display is compatible to all Raspberry Pi, Arduino, CubieBoard, Banana Pi and microcontroller without additional effort. Specifications Chipset Philips PCD8544 Interface SPI Resolution 84 x 48 Pixels Power supply 2.7-3.3 V Special features Backlight Compatible to Raspberry Pi, Arduino, CubieBoard, Banana Pi and microcontroller Dimensions 45 x 45 x 14 mm Weight 14 g

    € 12,95

    Members € 11,66

  • Last stock! "\"JOY-iT 10\"Touchscreen voor RPi incl. metalen behuizing en stand (HDMI/VGA/BNC/AV)\"\"\""

    JOY-iT JOY-iT 10" Touchscreen for RPi incl. Metal Case and Stand (HDMI/VGA/BNC/AV)

    1 review

    2 in stock

    The 10' Touch-Display from JOY-iT is housed in a sleek metal case making it the perfect choice for a wide range of applications. The case is robust and has a smooth matt black finish which blends well with the hard-coated (3H) screen. Included with the display is an adapter plate which can be used to mount any of the standard single board computers on the rear of the unit. The USB socket can power the display when it’s used with an SBC so there will be no need to use the included mains adapter. The display can also be used as a monitor for standard PC systems via the HDMI and VGA connectors. A BNC and AV connector provide analog inputs for CCTV etc. Features Includes an adapter plate for mounting all the standard Single Board Computers (SBC) such as Raspberry Pi, BeagleBone, CubieBoard etc. Needs no separate mains adapter when used with an SBC Robust metal case Anti-glare display Hard coated (3H) display surface Specifications Display size 10.1” (25.65 cm) Visible display surface 217 x 135.6 mm Resolution 1280(RGB) x 800(WXGA) pixel Contrast ratio 800:1 Bracket and stand Included HDMI connector 1x VGA connector 1x AV connector 1x BNC connector 1x USB connector 2x Integrated loudspeaker Yes Mains adapter 12 V / 2000 mA Operating Temperature 0 ~ 50°C Brightness 350 cd/m² Displayed colors 16.7 million Special features Hard coated (3H) anti-glare display Weight 1.20 kg Dimensions without stand 244 x 163 x 32 mm (B x H x T) Included Display (10.1”) Stand Adapter plate for mounting an SBC HDMI cable USB cable (Type A) USB cable (Type A to Micro-USB) Mains adapter Remote controller Downloads Pre-installed Raspbian System for Raspberry Pi 4 Pre-installed Raspbian System for Raspberry Pi 3B+ and older

    2 in stock

    € 199,95

    Members € 179,96

  • JOY-iT 5` Touchscreen for Raspberry Pi

    JOY-iT JOY-iT 5" Touchscreen for Raspberry Pi

    Display: 5' (12.7 cm) Weight: 159 g Resolution: 800 x 480 pixels Display Type: Touch-Control Amount HDMI-HDMI Adapter: 1x Micro USB Interface (only Power): 1x Supports Raspberry: Raspbian, Ubuntu Dimensions, without mounting: 120 x 79 x 7 mm Scope of supply: 5 inch HDMI LCD, HDMI-HDMI Adapter, Touchpen

    € 62,95

    Members € 56,66

  •  -15% JOY-iT Joy-View 15 Touchscreen

    JOY-iT JOY-iT Joy-View 15 Touchscreen

    Specifications Resolution 1920 x 1080 Screen Size 15.6' Refresh Rate 60 Hz Contrast 800:1 Brightness 300 nit Screen Type TFT IPS LCD Backlight LED Backlight Color Gamut 16.7M, NTSC 72%, sRGB up to 100% Speaker Double Speaker Viewing Angle 178 ° Aspect Ratio 16:9 Power Supply 5 - 20 V or Type-C USB 3.0 Inputs Mini HDMI, Type-C, Voltage Input Outputs 3.5 mm Jack Plug Operating Temperature 0 °C - 50°C Case Aluminum Alloy Dimensions 360 mm x 230 mm x 10 mm Weight 1390 g Included Joy-View 15 Display Smart Case 1.5m HDMI to mini-HDMI cable 1m Type-C to Type-C cable 1m USB-A to USB-C cable Power Adapter HDMI to mini HDMI adapter Cleaning Towel

    € 399,00€ 339,00

    Members identical

  • Last stock! JOY-iT 7` Touchscreen for Raspberry Pi

    JOY-iT JOY-iT 7" Touchscreen for Raspberry Pi

    1 in stock

    Resolution: 1024 x 800 pixels Supported Devices: Raspberry Pi A+/ B+/ 2B / 3B, Banana Pi, Banana Pro, Windows-PCs Special features: Can also be used as an independent HDMI-Display LCD Type: TFT Connections: HDMI, Micro-USB Touch Controller: GT811 Touch-Panel: Type Capacitive (5 Multi-Touch) Backlight: LED Display-Size: 154.21 x 85.92 mm

    1 in stock

    € 79,95

    Members € 71,96

  • Pimoroni Inky Frame 5.7' (incl. Pico W)

    Pimoroni Pimoroni Inky Frame 5.7" (incl. Pico W)

    Inky Frame 5.7' features a nice, big seven color E Ink display with loads of space for displaying images, text, graphs or interfaces. There's five buttons with LED indicators for interacting with the display, two Qw/ST connectors for plugging in breakouts and a micro SD card slot for all-important storage of cat photos. Every Inky Frame comes with a pair of sleek little metal legs so you can stand it up on your desk (and a selection of mounting holes if you'd prefer to do something else). There's also a battery connector so you can power it without annoying trailing wires, and some neato power saving features that mean you can run it from batteries for ages. Inky Frame is great for: Checking your calendar and upcoming appointments at a glance Attaching to your office door to display your availability Displaying motivational posters, quotes, or images (fungible or otherwise) Showing readouts from other wirelessly connected environmental boards Features Raspberry Pi Pico W Aboard Dual Arm Cortex M0+ running at up to 133 Mhz with 264 kB of SRAM 2 MB of QSPI flash supporting XiP Powered and programmable by USB micro-B 2.4 GHz wireless 5.7' EPD display (600 x 448 pixels) E Ink Gallery Palette 4000 ePaper ACeP (Advanced Color ePaper) 7-color with black, white, red, green, blue, yellow, orange. Ultra wide viewing angle – >170° Dot pitch – 0.1915 x 0.1915 mm 5x Tactile buttons with LED indicators Two Qw/ST connectors for attaching breakouts microSD card slot Dedicated RTC chip (PCF85063A) for deep sleep/wake Fully assembled No soldering required. C/C++ and MicroPython libraries Schematic Included 1x Inky Frame 5.7' (incl. Pico W) 2x Metal legs Downloads MicroPython (Learn) Getting Started with Inky Frame (Readme) Installing MicroPython (Readme) MicroPython FAQs (and troubleshooting) Download pirate-brand MicroPython (you'll want the Inky Frame.uf2) MicroPython examples PicoGraphics function reference C/C++ C examples Picographics function reference

    € 109,95

    Members € 98,96

If you are looking for a way to take your electronics projects to the next level, then a Raspberry Pi display is exactly what you need. Elektor offers a wide range of high-quality displays that allow you to easily expand the capabilities of your Raspberry Pi.

Expansion options with Raspberry Pi displays

If you want to improve your Raspberry Pi and make it more powerful by adding ingenious accessories, Elektor displays are the perfect solution. These displays are specially designed to improve the performance of your mini computer.

They are compatible with most Raspberry Pi models. By adding a display, you transform your Raspberry Pi into a full-fledged computer station and all kinds of additional applications are possible.

Which display suits your project?

Most Raspberry Pi displays are sets with an LCD screen and a high-quality circuit board. Dimensions and specifications vary per display. Elektor offers various display options in terms of colors, size, pixels and a possible touchscreen option.

Which display best suits your project depends very much on your specific preference in terms of size and number of pixels, among other things. But whether you need a smaller or larger display, Elektor always has a suitable option in its extensive range!

Compact options

We also offer compact displays that are ideal for portable projects, such as digital cameras, robots and other mobile devices. These displays are small and lightweight, making them easy to integrate into your project. The displays have the same high quality as the larger options, so you can always count on the best performance.

Getting started with your display

To use your Raspberry Pi display, you only need some basic skills. Most displays come with a manual that explains step by step how to install the product. With some patience and careful following of the instructions, nothing can go wrong!

Order your Raspberry Pi display immediately!

If you're looking for a way to improve your Raspberry Pi, adding a display is the perfect choice. Elektor offers a wide range of high-quality displays in different sizes and pixels. By following the correct instructions, you can easily get started with your display and take all your projects to the next level.

Login

Forgot password?

Don't have an account yet?
Create an account