With these jumper wires (length: 20 cm) you can connect a Raspberry Pi or an Arduino with breadboards. Each cable consists of 40 individual wires/pins which can also be separated. Included 1x 40-pins female to female 1x 40-pins male to male 1x 40-pins male to female
This comprehensive starter kit contains a wide range of important electronic components. From resistors and capacitors to LEDs, switches, buzzers and a breadboard with jumper wires – this kit contains everything you need to get started with your electronics projects.
Contents
1x High Quality Retail Box
10x 1/4W 1% 100R Resistor
10x 1/4W 1% 220R Resistor
10x 1/4W 1% 330R Resistor
10x 1/4W 1% 1K Resistor
10x 1/4W 1% 10K Resistor
10x 1/4W 1% 100K Resistor
10x 1/4W 1% 4.7K Resistor
10x 1/4W 1% 47K Resistor
10x 100PF Ceramic Capacitor
10x 10NF Ceramic Capacitor
10x 100NF Ceramic Capacitor
10x 22PF Ceramic Capacitor
10x 10UF aluminum electrolytic capacitor
10x 470UF aluminum electrolytic capacitor
10x Red LED
10x Green LED
10x Yellow LED
10x Blue LED
8x 12x12x7.3 Switch
2x Red Cap
2x Yellow Cap
2x Green Cap
2x Blue Cap
1x 10K Precision Potentiometer
2x RGB LED
1x Active Buzzer
1x Passive Buzzer
1x Pin Header 1x40
1x Resistor Card
1x 400pts Breadboard
1x 30pcs/pack Breadboard Jumper Wires Set
The Throwing Star LAN Tap Pro is a passive Ethernet tap, requiring no power for operation. There are active methods of tapping Ethernet connections (e.g., a mirror port on a switch), but none can beat passive taps for portability. To the target network, the Throwing Star LAN Tap looks just like a section of cable, but the wires in the cable extend to the monitoring ports in addition to connecting one target port to the other.The monitoring ports (J3 and J4) are receive-only; they connect to the receive data lines on the monitoring station but do not connect to the station’s transmit lines. This makes it impossible for the monitoring station to accidentally transmit data packets onto the target network.The Throwing Star LAN Tap Pro is designed to monitor 10BASET and 100BASETX networks. It is not possible for an unpowered tap to perform monitoring of 1000BASET (Gigabit Ethernet) networks, so the Throwing Star LAN Tap intentionally degrades the quality of 1000BASET target networks, forcing them to negotiate a lower speed (typically 100BASETX) that can be passively monitored. This is the purpose of the two capacitors (C1 and C2).Like all passive LAN Taps, the Throwing Star LAN Tap Pro degrades signal quality to some extent. Except as described above for Gigabit networks, this rarely causes problems on the target network. In situations where very long cables are in use, the signal degradation could reduce network performance. It is a good practice to use cables that are not any longer than necessary.DownloadsOpen source design files
Features
Built-in USB to TTL transfer chip
TTL interface output, easy to connect to the MCU
Status LED
Dual 3.3 V and 5 V power output, working with 3.3 V and 5 V target device
Size: 55 x 16 mm
This FTDI USB to TTL (3.3 V I/O) Serial Cable (FTDI TTL-232R-3V3 OEM) is a professional, high quality, high speed device which allows a simple and easy way to connect TTL interface devices using a spare USB port. Features TTL-232R-3V3 FTDI USB to TTL 3.3 V Serial Cable FTDI TTL-232R-3V3 Cable 6 Way The FTDI USB to TTL 3.3 V features a FTDI FT232R device integrated within the cable FTDI USB to TTL Serial 3.3 V Adapter Cable 6 Pin 0.1' Female Socket Header UART IC FT232RL Chip Compatible with Windows 7/8/10 and Linux
The Cleqee P1503E Multimeter Test Lead Kit is a reliable tool that provides safe and accurate measurements of electrical performance. Compatible with multimeters, clamp meters and other test instruments, this kit ensures versatility and precision for a wide range of testing applications.
With removable tips, banana plugs, crocodile clips and cable lugs, the kit offers extended testing capabilities and flexibility. The rubber-coated surfaces provide a secure and comfortable grip and improve stability even in slippery conditions.
The kit includes 8 interchangeable test probes – 4 in nickel-plated copper and 4 in gold-plated copper – specially designed to access the tightest spots, making them ideal for SMD testing. In addition, the insulated, flexible silicone gripping hooks act as an extra hand during testing, allowing sequential testing of components. The powerful spring mechanism ensures a firm grip on tiny components and minimizes the risk of short circuits.
Included
2x 1.4 mm Banana Plug Mutimeter Probe Test Leads, Length: 1 m (red & black)
Replaceable Needles Kit
4x Gilded sharp needle
4x Standard needle
2x Protective Cap (red & black)
2x U-Type Insert (red & black)
2x 2 mm inner spring to 4 Mmm male banana plug adapter (red & black)
2x Crocodile Clips (red & black)
2x IC testing hook (red & black)
1x 4 mm banana plug testing clip
The SparkFun Qwiic Adapter provides the perfect means to make any old I²C board into a Qwiic-enabled board. This adapter breaks out the I²C pins from the Qwiic connectors to pins that you can easily solder with your favorite I²C-enabled device. The Qwiic Adapter has two Qwiic connection ports, all on the same I²C bus. Four plated through holes are broken out for SCL, SDA, 3.3V and GND. These pins can be used to convert an old I²C-enabled device into a Qwiic-enabled board. Features 2x Qwiic Connection Ports Broken-out I²C Pins
An assortment of coloured wires: you know it's a beautiful thing. Six different colours of stranded wire in a cardboard dispenser box. Sit this on your workbench, and stop worrying about having a piece of wire around!
Included
22 AWG
25 ft / Spool
6 Spools in Six Different Colors
Colours are Red, Blue, Yellow, Green, Black, and White
Dispenser Box
This is a 100mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components but can be used for other applications as well. Each Qwiic Cable's wires have been colour-coded to Red, Black, Blue, and Yellow.
The universal 4 Pin connector is a white 4-pin buckled connector used on Stem, Twigs and Grove cables. The pin spacing is 2 mm. There are 10 connectors per bag. They can be used in DIY projects.
Specifications Datasheet Resonance Frequency (FO): 680 ±20% Hz at 1 V Rated Impedance: 8 ±20% Ω (at 1 KHz) Frequency Range: ~600-10 KHz Rated Input Power: 0.25 W Max Input Power: 0.5 W Temperature Range: -20ºC ~ 55ºC Dimensions Diameter: 28 mm / 1.1' Height: 4.5 mm Weight: 6 g
Features Pitch spacing is 2.54 mm (1 to 36 contacts per row) with vertical orientation Number of contacts: 40 Number of rows: 2 Gender: receptacle Contact termination type: Through hole Contact Plating: Tin plated contacts High operating temperature range of -55°C to 105°C for matte tin plated contacts Contact material is phosphor bronze Black glass filled polyester insulator material Tiger Buy contact system Complies with UL E111594 and CSA 090871_0_000 standards
The MicroMod DIY Carrier Kit includes five M.2 connectors (4.2mm height), screws, and standoffs so that you can get all the special parts you may need to make your own carrier board. MicroMod uses the standard M.2 connector. This is the same connector found on modern motherboards and laptops. There are various locations for the plastic ‘key’ on the M.2 connector to prevent a user from inserting an incompatible device. The MicroMod standard uses the ‘E’ key and further modifies the M.2 standard by moving the mounting screw 4mm to the side. The ‘E’ key is fairly common so a user could insert an M.2 compatible Wifi module. Still, because the screw mount doesn’t align, the user would not secure an incompatible device into a MicroMod carrier board. Features 5x Machine Screws Phillips Head #0 (but #00 to #1 works) Thread: M2.5 Length: 3 mm 5x SMD Reflow Compatible Standoffs Thread: M2.5 x 0.4 Height: 2.5 mm 5x M.2 MicroMod Connectors Key: E Height: 4.2 mm Pin count: 67 Pitch: 0.5 mm
SMA Straight Plug to SMA Straight Plug, 76.2 mm
Specifications
Frequency range
0 to 18 GHz VSWR (≤1.35)
Insertion loss
≤0,22 db
Body
Brass Nickel
Centre contact
Brass Gold
Insulator
PTFE
The Whadda E12 is a high-quality carbon film resistor set comprising 610 pieces, with 10 pieces for each of the 61 standard E12 series values ranging from 10 Ω to 1 MΩ. Each resistor has a power rating of 0.25 W, a tolerance of 5%, and can operate within a temperature range of -55°C to 155°C. The maximum operating voltage is 250 V.
These resistors are suitable for applications in TVs, audio and video equipment, telephone receivers, communication systems, instrumentation, and home appliances.
This 14-way MonoDAQ-compatible connector allows the user to create, reuse and archive test fixtures instead of rewiring the connector furnished with the MonoDAQ everytime a measurement or test has to be repeated. Helps the user to build a library of plug-and-play test setups. Features Time saving push-in connection, tools not required Defined contact force ensures that contact remains stable over the long term Intuitive use through colour coded actuation lever Operation and conductor connection from one direction enable integration into front of device All necessary technical data can be found here.