The UT196 True RMS solar multimeter is an ideal tool for solar power system maintenance. This rugged meter is designed for technicians who work in rugged outdoor environments. UT196 can measure up to 1700 V DC and 1500 V AC voltages, and 3000 A AC current with an external current clamp sensor. This solar meter offers IP65 protection and able to withstand 2 m drop as well. The UT196 solar multimeter is designed with 1700 V DC, 1500 Vrms AC overload protection and tested for safe usage in CAT III 1000 V, CAT IV 600 V environments. Features True RMS Measure up to 1700 V DC and 1500 V AC for high voltage applications e.g. solar array, wind IP65 protection CAT III 1000V, CAT IV 600 V Analog bar Frequency response: 45 Hz~1 kHz Low-pass filter function Low impedance mode Built-in flashlight, bright backlight and visual alarm Applications High DC voltage measurement Output voltage and frequency measurement Voltage and frequency measurement Current and frequency measurement Specifications Range UT196 DC voltage (V) 1700 V ±0.2% +5 AC voltage (V) 1500 V ±0.8% +3 Frequency (Hz) 1 MHz ±0.08% +4 Resistance (Ω) 60 MΩ ±0.8% +2 Capacitance (F) 60 mF ±1.9% +5 Power 9 V battery Dimensions 195 x 95 x 58 mm Included UT196 Solar Multimeter Battery Test leads Downloads Datasheet Manual

Read more less

Features Four fully independent sensor elements on one package. The ability to detect a variety of gases, besides Carbon monoxide (CO), Nitrogen dioxide (NO2), Ethyl alcohol(C2H5CH), Volatile Organic Compounds (VOC), etc. Qualitative detecting, rather than quantitative. Compact size for easy deployment. Included 1x Multichannel gas sensor board 1x Grove cable

Read more less

2-ch CAN HAT+ is an isolated expansion board for Raspberry Pi. It supports dual-channel CAN communication and features multi-protection circuits, wide voltage input, and more. Features Designed for Raspberry Pi Standard HAT+ design, with onboard EEPROM chip. Adopts MCP2515 and SN65HVD230 dual-chip solution, allowing 2-channel CAN communication. Integrated power isolation, providing stable isolated voltage, requires no extra power supply for the isolated terminal. Onboard digital isolation chip, signal isolation communication is safer, more stable, and better anti-interference. Onboard SM24CANB (transient voltage suppressor), provides ESD protection and transient peak voltage protection. Onboard voltage conversion circuit, select 3.3 V/5 V operating voltage by jumper. Onboard 120 Ω terminal resistor, enable through the jumper cap. Elicits the SPI control interface, for connecting with host control boards like STM32/Arduino. Provides online supporting information manuals and demos. Specifications CAN controller MCP2515 Control Bus SPI Power supply method External power supply terminal or Raspberry Pi GPIO Terminal voltage input DC 7~36 V Operating voltage 5 V Logic level 3.3 V/5 V Dimensions 65.0 x 56.5 mm Downloads Wiki

Read more less

The PCW05A True RMS Digital Clamp Meter is a versatile and reliable tool that can be used for a variety of applications. It can measure AC/DC voltage, current, resistance, capacitance, frequency, duty ratio, and temperature. The digital clamp meter is equipped with an Auto-Range function, which can detect automatically the correct measurement range for the chosen measurement function, making it very user-friendly. The 6000 counts display provides precise result read-outs. The LPF (Low Pass Filter), LowZ (Low Impedance), & DCA ZERO (Zero Correction) functions ensure accurate measurements. With its backlight LCD display and LED work light, the PCW05A can provide clear readings in low-light conditions. In addition, the bi-color display changes its color to orange in order to warn the user when measuring high current or voltage. Overall the PCW05A digital clamp meter is the perfect choice for professionals and hobbyists alike. Features CAT III 600 V; measures up to 600 A AC/DC current 6000 counts, True RMS Auto Range function Jaw opening: 2,5 cm AC/DC voltage, AC/DC current, resistance, capacitance, frequency, duty ratio, and temperature measurement NCV (non-contact voltage detection), continuity, and diode test Bi-color backlight LCD display (changes color to orange when measuring high currents / voltages) LPF (Low Pass Filter), LowZ (Low Impedance), & DCA ZERO (Zero Correction) functions Data hold with Max/Min function LED work light for working in dark environments Small and compact size making it a very handy tool Great packaging design and manual with pictures in various languages: EN, GER, ES, FR, PT, PL, IT Includes batteries, high-quality test leads, temperature probe, & transport case

Read more less

PicoVision is a powerful digital video stick for bold audio visual adventures, with dual RP2040 chips and a conveniently HDMI-shaped output connector to boot. Use PicoVision to make and run your own homebrew games, draw digital art, recreate beloved demos, screensavers or WinAmp visualisations, visualise data, subvert advertising billboards, emulate CeeFax or whip up signage. GPU (RP2040)Does all the heavy-lifting to display buttery-smooth, high-res, animations on your TV or monitor via HDMI. CPU (Pico W)Runs your code and provides an interface to other gadgets through USB, Wi-Fi, and Bluetooth. HDMI connectorMake use of TVs, monitors, giant projectors, or even tiny displays for building into a cosplay outfit. Line out audioBash out some bleeps and bloops! This digital audio interface can produce some quality noise. microSD cardNever run out of space for your lovely assets by adding a sizeable microSD card to your setup. Qw/ST connectorAdd sensors or other types of breakout to your project so they can react to the world around them. On-board reset and user buttonsCreate a simple user interface for your project without needing to add any extras. You can program PicoVision using C++ or MicroPython. C++ will get you the best performance, but if you're a beginner we'd recommend MicroPython for ease of getting started. Either way, you'll have access to PicoGraphics libraries which will let you easily manipulate shapes, text and images, some exciting new vector graphics and font functionality courtesy of PicoVector, and the ability to make bleeps, bloops and other fun electronic noise with PicoSynth. Features Raspberry Pi Pico W (CPU) Dual Arm Cortex M0+ with 264 kB of SRAM 2 MB of QSPI flash supporting XiP 2.4 GHz wireless / Bluetooth 5.2 RP2040 (GPU) Another dual Arm Cortex M0+ with 264 kB of SRAM Higher resolution modes use significant GPU overclocking Connects to the CPU as an I²C peripheral device 2x 8 MB PSRAM chips for frame double-buffering Digital Video out via HDMI connector PCM5100A DAC for line level audio over I²S, wired to a 3.5 mm stereo jack MicroSD card slot 3x user buttons (one wired to CPU, two to GPU) Reset button Status LED (GPU) Qw/ST (Qwiic/STEMMA QT) connector Fully-assembled (no soldering required) Spare/extra pins broken out as unpopulated headers (these require soldering) C++/MicroPython libraries Downloads Pinout Schematics MicroPython for PicoVision MicroPython examples and documentation

Read more less

The 741SE is an easy-to-build surface-mount soldering kit. It includes the circuit board, resistors, and transistors that make up the electrical circuit as well as printed assembly instructions. The kit also comes complete with the 'IC Leg' stand, and 8 color coded thumbscrew terminal posts. To build the 741SE, basic electronic soldering skill and tools are required, but no additional knowledge of electronics is presumed or required. You provide standard surface-mount soldering tools: a soldering iron, solder (wire or paste), small metal tweezers, as well as a Phillips head screwdriver. The kit features relatively large surface mount components (1206 and SOT-23), and is a great first surface-mount soldering kit if you're just getting started. However, if you are experienced at surface mount soldering and have tools like a hot air rework station or other equipment, you're welcome to use them for assembling this kit. Features Anodized aluminium stand 8x 4-40 surface-mount threaded inserts Stainless steel thumbscrews with colour-coded plastic caps (1 red, 1 black, 6 grey) All materials (including the circuit board and stand) are RoHS compliant (lead-free) Dimensions: 6.5 cm × 5.2 cm x 1.6 mm Dimensions assembled: 6.5 cm × 7.8 cm × 2.0 cm

Read more less

This outdoor antenna made of fiberglass is optimized for the reception of ADS-B signals on the 1090 MHz frequency. The antenna consists of a half-wave dipole with 5 dBi gain, encapsulated inside a fiberglass radome with an aluminum mounting base. With a Raspberry Pi, an RTL-SDR and this antenna, you can receive position data from aircraft in your area for apps such as Flightradar24 or FlightAware. Specifications Frequency 1090 MHz Antenna type Dipole 1/2 wave Connector N female Installation type Mast Diam 35-60 mm (mounting bracket included) Gain 5 dBi SWR ≤1.5 Type of Polarization Vertical Maximum power 10 W Impedance 50 Ohms Dimensions 62.5 cm Tube diameter 26 mm Base antenna 32 mm Operating temperature −30°C to +60°C Included ADS-B antenna (1090 Mhz) Mast bracket (for installation on a 35 to 60 mm diameter mast)

Read more less

This mini IPS 7-inch HD monitor supports a resolution of 1024x600. IPS monitors help keep colors consistent at a wide viewing angle. The 2 removable speakers enhance your audio-visual experiences. Features Four corner holes let you mount the small monitor onto your DIY IoT projects that you’re working on. This Raspberry Pi display also comes with 2 stands, is easy to install and remove, great for on-the-go use. With a capacitive USB touchscreen, simply power the USB touch port to achieve touch function and no need to install the driver, just plug and play! Signal via HDMI-compatible port, power&touch via micro USB port, drive free. No cable solution to Raspberry Pi 4, just using 2 simple adapters to connect your Raspberry Pi 4 directly. You can use it with your Raspberry Pi 4/3/2, Laptop, TV, video game console like Nintendo Switch/Xbox/PS4, and security camera. 170-degree wide view angle 5-point capacitive HD touch display Specifications Display size 7 inch (154 x 86 mm) Resolution 1024 x 600 Display type IPS Touch Capacitive Touchscreen Frame rate 60 fps Brightness 260 cd/m² Speaker Support Interface HD & USB Working temperature −20 to +60°C Dimensions 164 x 99 mm Weight 235 g Included 1x 7-inch Monitor 1x USB to Micro USB Connector 1x HD to Micro HD Connector 1x USB to Micro USB Cable 1x HD to HD Cable 4x M2.5 Screws 4x Small Copper Pillars 2x Pro Stand 2x M3 Screws 2x Speakers 1x User Manual Downloads User Manual

Read more less

The Ardi Display Shield features a vibrant 2" IPS screen with a resolution of 240 x 320 pixels, providing sharp and crisp visuals for your projects. Whether you're working on a small-scale project or a complex prototype, this display shield ensures clear and vibrant display output. With 2 programmable buttons, you have the flexibility to create interactive experiences and user-friendly interfaces. Customize the buttons to trigger specific actions or navigate through menus effortlessly. The possibilities are endless, limited only by your imagination. In addition to the programmable buttons, the Ardi Display Shield also includes a 5-way joystick for intuitive control. With the joystick's SPI interface, you can easily navigate menus, scroll through options, and control various aspects of your Arduino project with precision and ease. Designed with compatibility and ease of use in mind, the Ardi Display Shield seamlessly integrates with the Arduino Uno board. Simply connect it to your Arduino Uno and unlock a world of possibilities for visual feedback, user interaction, and data visualization. Features Onboard 2.0" TFT Display Compatible with 3.3 V/5 V MCU, Selection provided Onboard 5-Way Joystick allows better control-related projects Two programmable Buttons to add additional functionality to project Mounts directly onto ArdiPi, Ardi32 or other Arduino compatible boards Specifications Display resolution: 240x320 pixels Pixel Pitch: 0.1275 x 0.1275 mm Active Area: 30.6 x 40.8 mm Module Size: 34.6 x 47.8 x 2.05 mm SPI Interface Display Colors: 65K colors Drive IC: ST7789V2 Viewing Direction: All-view the best image

Read more less

Components are both shrinking and getting increasingly finer pitch year after year but your PCBs might have grown in size or the number of interconnected PCBs or the number of handsfree PCBite probes needed to test your design may have increased making it crowded on our other smaller base plates. Features With a size of 297 x 420 mm (DIN A3) the extra large baseplate has room for most PCBs and many handsfree PCBite probes for those measurements sessions where more channels than available is needed. So if you are looking for more space, extra protection or just want to clean up your work surface then this accessory is a perfect match. Designed to be used with Sensepeeks magnetic PCBite line of products including PCB holders, hands free probes and magnifier. Included 1x XL base plate (DIN A3) with pre-fitted insulation cover

Read more less

Build your 3D led cube and create unlimited 3D effects. The unit comes standard loaded with effects. Connect to your computer (USB) and create your own! Features LEDs: 5 x 5 x 5 = 125 LEDs User programmable via USB (creation of animation/scenes) Large amount of user programmable frames Frames are separately dimmable 4 transition speeds Available frames: 3200 5 levels LED dimming available No coding skills required Software similar to (3 x 3 x 3) Specifications Regulated power supply: 9 VDC (not incl.) Power consumption: 300 mA max. Dimensions: 110 x 110 x 150 mm

Read more less

Inky Frame 4.0" features a vibrant E Ink display with 640 x 400 pixels of tightly packed seven colour goodness – that's almost as many pixels as on the 5.7" Inky Frame, but squished tidily into a smaller footprint. There's five buttons with LED indicators for interacting with the display, two Qw/ST connectors for plugging in breakouts and a micro SD card slot for storage of capybara photos or other vital files. Every Inky Frame comes with a pair of sleek little metal legs so you can stand it up on your desk. There's also a battery connector so you can power it without annoying trailing wires, and some neato power saving features that mean you can run it from batteries for ages. Inky Frame 4.0" is great for: An ultra readable, low power consumption home automation dashboard Displaying stylised photos, pop art images or favourite comic panels. Showing cute graphs and readouts from local or wirelessly connected sensors Displaying fascinating data from online APIs. Features Raspberry Pi Pico W Aboard Dual Arm Cortex M0+ running at up to 133 Mhz with 264 kB of SRAM 2 MB of QSPI flash supporting XiP Powered and programmable by USB micro-B 2.4 GHz wireless 4.01' EPD display (640 x 400 pixels) E Ink Gallery Palette 4000 ePaper ACeP (Advanced Color ePaper) 7-color with black, white, red, green, blue, yellow, orange. Ultra wide viewing angles Ultra low power consumption Dot pitch – 0.135 x 0.135 mm 5x Tactile buttons with LED indicators Two Qw/ST connectors for attaching breakouts microSD card slot Dedicated RTC chip (PCF85063A) for deep sleep/wake Fully assembled (no soldering required) C/C++ and MicroPython libraries Schematic Included 1x Inky Frame 4.0' (incl. Pico W) 2x Metal legs Downloads MicroPython (Learn) Getting Started with Inky Frame (Readme) Installing MicroPython (Readme) MicroPython FAQs (and troubleshooting) Download pirate-brand MicroPython (you'll want the Inky Frame.uf2) MicroPython examples PicoGraphics function reference C/C++ C examples Picographics function reference

Read more less