The FNIRSI SWM-10 is an efficient, practical and easy-to-carry handheld spot welder with a built-in 5000 mAh lithium battery that also functions as a power bank. The double-pulse spot welding technology makes the welding more stable and firm. Features 5000 mAh lithium battery for long battery life Fast charging power bank High-resolution 1.8" TFT LCD color screen Built-in intelligent temperature control sensor, over temperature, low voltage and short circuit protection Customized settings for preheat, pulse, interval and number of connection points make welding more stable and safer Can weld nickel sheets, iron sheets, stainless steel sheets, etc. The maximum welding thickness is 0.25 mm, and the welding current is 1200 A. Specifications Capacity 5000 mAh Charge 5 V/2.1 A Discharge 5 V/2.1 A Welding materials Nickel sheet, iron sheet, stainless steelsheet, aluminum sheet Welding thickness 0.1-0.25 mm Maximum welding current 1200 A Gear 4 combination gear adjustment Dimensions 155 x 82 x 28 mm Included 1x FNIRSI SWM-10 Spot welder 2x Spot welding pens 1x Nickel sheet 2x Spare needles 1x USB cable 1x Manual Downloads Manual Firmware V1.4

Read more less

HackRF One is a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1 MHz to 6 GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation. Specifications 1 MHz to 6 GHz operating frequency Half-duplex transceiver Up to 20 million samples per second 8-bit quadrature samples (8-bit I and 8-bit Q) Compatible with GNU Radio, SDR and more Software-configurable RX and TX gain and baseband filter Software-controlled antenna port power (50 mA at 3.3 V) SMA female antenna connector SMA female clock input and output for synchronization Convenient buttons for programming Internal pin headers for expansion Hi-Speed USB 2.0 USB-powered Open source hardware HackRF One is test equipment for RF systems. It has not been tested for compliance with regulations governing transmission of radio signals. You are responsible for using your HackRF One legally. Included 1x HackRF One SDR 1x Plastic enclosure 1x micro-USB cable Note: An antenna is not included. ANT500 is recommended as a starter antenna for HackRF One. Downloads Documentation GitHub Source code and hardware design files

Read more less

RTL-SDR is an affordable dongle that can be used as a computer-based radio scanner for receiving live radio signals between 500 kHz and 1.75 GHz in your area. The RTL-SDR V4 offers several improvements over generic brands including use of the R828D tuner chip, triplexed input filter, notch filter, improved component tolerances, a 1 PPM temperature compensated oscillator (TCXO), SMA F connector, aluminium case with passive cooling, bias tee circuit, improved power supply, and a built in HF upconverter. RTL-SDR V4 comes with the portable dipole antenna kit. It is great for beginners as it allows for terrestrial and satellite reception and easy to mount outdoors and designed for portable and temporary outside usage. Features Improved HF reception: V4 now uses a built-in upconverter instead of using a direct sampling circuit. This means no more Nyquist folding of signals around 14.4 MHz, improved sensitivity, and adjustable gain on HF. Like the V3, the lower tuning range remains at 500 kHz and very strong reception may still require front end attenuation/filtering. Improved filtering: The V4 makes use of the R828D tuner chip, which has three inputs. The SMA input has been triplexed input into 3 bands: HF, VHF and UHF. This provides some isolation between the 3 bands, meaning out of band interference from strong broadcast stations is less likely to cause desensitization or imaging. Improved filtering x2: In addition to the triplexing, the open drain pin on the R828D can be also used, which allows to add simple notch filters for common interference bands such as broadcast AM, broadcast FM and the DAB bands. These only attenuate by a few dB, but may still help. Improved phase noise on strong signals: Due to an improved power supply design, phase noise from power supply noise has been significantly reduced. Less heat: Another advantage of the improved power supply is low power consumption and less heat generation compared to the V3. Included 1x RTL-SDR V4 dongle (R828D RTL2832U 1PPM TCXO SMA) 2x 23 cm to 1 m telescopic antenna 2x 5 cm to 13 cm telescopic antenna 1x Dipole antenna base with 60 cm RG174 1x 3 m RG174 extension cable 1x Flexible tripod mount 1x Suction cup mount Downloads Datasheet User Guide Quick Start Guide SDR# User Guide Dipole Antenna Guide

Read more less

LCR/ESR Meter, Multimeter, SMD Tester with built-in Micro Signal Generator The Miniware DT71 digital tweezers are a truly 'smart' buy for pro engineers and makers alike. The compact DT71 has a unique trinary structure which can be separated into the controller, testing arms, and tweezer tips. You can use the DT71 to take measurements and to automatically identify SMD components such as resistors, capacitors, and diodes. Highlights DT71 Mini Digital Tweezers is a tool for multi-function measurements with full differential input measurement. DT71 has a unique trinary structure, which can be separated into the controller, testing arms, and tweezer tips, flexible to be replaced and combined. It is compact and pocket-size for easy carrying. You can use it in laboratories, workbenches, warehouses, and in the field. It also has dual built-in rechargeable lithium batteries that can last 10 hours at a stretch with a single full charge that takes about 2 hours to charge. DT71 Mini Digital Tweezers have an OLED screen on the 360° rotatable controller, providing visibility at all angles. Smart gesture recognition will automatically identify left/right-hand operation and adjust screen display. It has various measurement types to fulfill all your needs. The test arms of DT71 Mini Digital Tweezers use magnetic elasticity to provide an easy clipping, ergonomic, and long-lasting structure. DT71 Mini Digital Tweezers features a pair of beautiful intensified gold-plated interchangeable tweezer tips, which enables higher measuring accuracy. DT71 Mini Digital Tweezers have manual and automatic Identification modes. In auto mode, DT71 can automatically identify SMDs including resistor, capacitor, inductor, and diode, showing both main and secondary parameters, very useful in fast distinguishing different components. Meanwhile, a built-in miniature waveform signal generator can output a variety of waveform signals. DT71 provides a perfect solution for debugging and maintenance of complex electronic systems and the classification and detection of discrete chip components. Different from other LCR testers, DT71 Mini Digital Tweezers have no physical buttons, instead, it has a hidden touch button on top of the controller, which makes it easy to operate with only a light touch. DT71 Mini Digital Tweezers has intelligent functions such as Automatic identification, Automatic shutdown, and also the firmware can be upgraded. Features Innovative trinary structure: separated into the controller, testing arms, and tweezer tips, which are flexible to be replaced and combined. 360° rotatable controller with OLED screen, with good viewing angles. Smart gesture recognition with automatic identification of left/right-hand operation and adjusting the screen orientation accordingly. Hidden touch button on top of the controller, which makes it easy to operate with only a light touch. Test arms use magnetic elasticity to provide an easy clipping, ergonomic, and long-lasting structure. Built-in dual lithium batteries in test arms, balancing both arms and providing a longer standby time. Several kinds of gold-plated interchangeable tweezer tips, enabling higher measurement accuracy in various usages. Automatically identify SMDs including resistor, capacitor, inductor, and diode, showing both main and secondary parameters. A built-in signal generator can output a variety of waveform signals. Specifications Product Specifications Operation time 10 hrs (in continuous operation) Charging time 2 hrs Display 96 x 16 OLED Size Controller 47 mm Test Arms 106 mm Weight 22 g Operation Hidden touch button Measurement Specifications Range Resolution Accuracy Resistance 0.1 Ω~1 KΩ 0.1 Ω 0.5%+2 1 KΩ~2000 KΩ 1 KΩ 0.5%+2 Capacitance 0.1 pF~1000 pF 0.1 pF 2%+3 0.001uF~400 uF 0.001 uF 2%+3 Inductance 1 uH~1000 uH 1 uH 5%+3 1 mH~50 mH 1 mH 5%+3 Voltage 1 mV~100 mV 1 mV 2%+5 0.1 V~40 V 0.1 V 1%+3 Frequency 10 Hz~1 KHz 10 Hz 0.1%+3 1 KHz~20000 KHz 1 KHz 0.1%+3 Diode Silicon diodes, Schottky diodes, LEDs (+0.1~3V) 0.1 V 1% Max input voltage -5 V~+50 V Source Impedance 1 MΩ Functions Automatic Identification Yes Designated Measurements Yes Continuity and Diode testing Yes Signal Generator SINE 10 KHz, 5 KHz, 2 KHz, 1 Khz, 500 Hz, 200 Hz NOISE 100 KHz USER 10 KHz, 5 KHz, 2 KHz, 1 Khz, 500 Hz, 200 Hz PULSE 100 KHz, 0 KHz, 20 Khz, 10 KHz, 5 KHz, 2 KHz, 1 Khz, 500 Hz, 200 Hz Included 1x DT71 Digital Tweezers 1x Test Arms 2x Tweezer Tips 1x Data Cable 1x Carrying Case 1x Safety Instructions Downloads Manual Firmware v1.15 Calibration v2.0

Read more less

The FNIRSI 2C23T is a fully functional, highly practical 3-in-1 dual channel digital oscilloscope with a high resolution 2.8-inch LCD display (320 x 240 pixels) designed for the maintenance and development industry. This device is equipped with 3 main functions: oscilloscope, multimeter and signal generator. The oscilloscope has an FPGA+MCU+ADC hardware architecture with a sampling rate of 50 MS/s, an analog bandwidth of 10 MHz and a built-in high-voltage protection module that supports the measurement of peak voltages of ±400 V maximum. The multimeter has a 4-digit 10000-point RMS value and supports AC/DC voltage and current measurements, as well as capacitance, resistance, diode, on/off and other measurement functions. Equipped with a built-in DDS function signal generator, it can output 7 kinds of function signals, with a maximum output of 2 MHz for all signals and a step of 1 Hz; the output frequency, amplitude and duty cycle are adjustable. The built-in 3000 mAh rechargeable lithium battery achieves a standby time of up to 6 hours. Features 2-ch oscilloscope 10 MHz bandwidth 50 MS/s real-time sampling rate 7 signal waveforms 10000 counts 2.8' HD color display (320 x 240 pixels) Dimensions: 167 x 89 x 35 mm Weight: 300 g Specifications Oscilloscope Dual channel, 2x 10 MHz bandwidth, 50 MS/s real-time sampling rate Maximum measured voltage: ±400 V FPGA+ADC+MCU high-performance hardware architecture, capturing waveform details without loss Equipped with complete triggering functions (auto, single, normal) Equipped with efficient automatic adjustment, the measured waveform can be displayed without complicated adjustment Save waveform screenshots, supports exporting images to a computer, facilitate secondary waveform analysis Multimeter 4-bit integer 9999 counting True RMS measurement Identification of voltage, current, capacitance, resistance, diode, on/off, and zero live wire Maximum input voltage: AC 750 V, DC 1000 V Automatic range, intelligent anti burning Data retention, color screen digital display Signal Generator 7 signal waveforms: sine wave, square wave, triangular wave, full wave, half wave, noise wave, DC Output frequency: 1 Hz-2 MHz Output amplituade: 0.1-3.3 V Output duty cycle: 0-100% Included 1x FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope 1x P6100 oscilloscope probes (10X) 1x Multimeter probe 1x Crocodile clip probe 1x USB-C charging cable 1x Manual Downloads Manual

Read more less

SmartScope is a compact 2-channel USB oscilloscope with a bandwidth of 30 MHz and a sampling rate of 2x 100 MSa/s. It is compatible with all major platforms, including Windows, macOS, Linux, and Android. The operation and display of measurement signals are done via smartphone, tablet, or PC. Additionally, a logic analyzer and a signal generator are integrated. Even more, you can get mobile with it: take the SmartScope on the road, thanks to the single-cable connectivity. Everything is going to be intuitive: pointing, pinching and swiping finally replaces the clunky interfaces of old scopes. With the SmartScope you develop your digital interfaces using the 100 MS/s logic analyzer. With this tool you can design any signal you want using Excel, then upload it to the built-in Arbitrary Waveform Generator (AWG). At the end capture the voltage at any point of your design at 100 million times each second. The Software for the support of Windows / macOS / Linux / Android and Export formats (Excel .csv / Matlab .mat) are given. Features Channel sampled at 100 MHz/s each AC/DC coupling on analog inputs 100% silent 64 Mbit RAM: x10000 zoom Arbitrary Waveform Generator 8 digital inputs at 100 MS/s each 4 digital outputs at 100 MS/s each Externally power your scope in case your mobile can't supply the juice. Specifications Oscilloscope Bandwidth 30 MHz (-3 dB point) Sample rate 2x 100 MS/s Channels 2 Max pre-trigger position 16x full scale Max post-trigger position Full scale Max full voltage scale 10 V/div (±35 V input range) Min full voltage scale 20 mV/div Analog input range -35 V, +35 V Max input peak-to-peak 40 V Signal coupling AC / DC Precision 8 bit Input impedance 1 MΩ // 10 pF Waverforms 200 waveforms/s Data delay to host < 10 ms Sample depth Up to 4 million samples per channel External trigger Yes Logic Analyzer Input channels 8 Input impedance 100 kOhm // 2 pF to GND Sample rate 100 MS/s Logic level 1.8 V to 5.0 V Diode protection Bidirectional Input data buffer 4 million samples Waverforms 200 waveforms/s Data delay to host < 10 ms Protocol decoders I²C, SPI, UART, I²S integrated User extensible Wave Generator (Analog Output) Output channels 1 Data rate Up to 50 MS/s Output level 0-3.3 V (Opamp driven) Output buffer Up to 2048 samples Max slew rate 30 ns/V Step 13 mV Wave Generator (Digital Output) Channels 4 Data rate Up to 100 MS/s Output level 3.3 V or 5 V (selectable) Output buffer Up to 2048 samples Diode protected Yes Programmable Logic USB controller MicroChip PIC18F14K50 USB interface PicKit3 or USB flashable FPGA Xilinx Spartan 6 FPGA interface JTAG and USB flashable Size & Weight Dimensions (L x W x D) 110 x 64 x 24.2 mm (4.33 x 2.52 x 0.95") Weight 158 g Case Aluminium Connectivity Device/Host mini USB included Record waveforms Store Matlab (.mat) or Excel (.csv) files through Dropbox Analog BNC 2 probes included Digital 8x 0.1" pitch, probes (included) Sync USB micro B-B Power USB micro B (optional) Included 1x SmartScope USB Oscilloscope 2x Analog probes 1x Digital probe cable 1x USB cable Downloads Manual Software GitHub Wiki

Read more less

Measuring conducted emission is the simplest and most affordable method of getting some indication of whether a design can meet EMI/EMC requirements. A Line Impedance Stabilization Network (LISN) is an indispensable part of an EMC pre-compliance test setup. In cooperation with Würth Elektronik, Elektor has developed a 5 µH, 50 Ω Dual DC LISN that supports voltages up to 60 V and currents up to 10 A. The instrument measures RF interferences on both channels (the power supply) by means of 5-μH blocking inductances. The internal 10-dB attenuation network – one in each channel – contains a 3rd-order high-pass filter with a cutoff frequency of 9 kHz to protect the input of instruments like a spectrum analyzer from potentially harmful DC voltages or low frequencies coming from the EUT (Equipment Under Test). Specifications RF path Channels 2 (with clamping diodes) Bandwidth 150 kHz – 200 MHz Inductance 5 μH || 50 Ω Internal attenuation 10 dB Connectors SMA DC path Max. current < 10 ADC Max. voltage < 60 VDC DC resistance < 2 x 70 mΩ PCB size 94.2 x 57.4 mm Connectors 4-mm banana Hammond enclosure Type 1590N Dimensions 121 x 66 x 40 mm Included 1x 4-layer PCB with all SMT parts fitted 1x pre-drilled enclosure with ready-printed front panel layout 5x gold-plated, insulated, 4-mm banana sockets, rated for 24 A, 1 kV 1x Hammond enclosure 1590N1, Aluminum (Die-Cast Alloy) More Info Project on Elektor Labs: Dual DC LISN for EMC pre-compliance testing Elektor 9-10/2021: EMC Pre-Compliance Test for Your DC-Powered Project (Part 1) Elektor 11-12/2021: EMC Pre-Compliance Test for Your DC-Powered Project (Part 2)

Read more less

The lab power supply JT-RD6006 provides up to 60 V and 6 A in combination with the powerful DC power source. Due to the keypad and a push and rotary encoder, the operation of the power supply unit is very comfortable. In addition, you can easily save and reload up to nine settings using the keypad. The high-resolution 2.4-inch colour display clearly shows all important information. The USB interface and an optional wireless network interface enable the device to be operated via PC or with an app from mobile devices. Moreover, the device has different protection and limit functions like constant voltage operation, constant current operation, overvoltage protection, overcurrent protection and replaceable fuses on the board itself (backside of the power supply). Specifications Input voltage 6-70 V Output voltage 0-60 V Output current 0-6 A Output power 0-360 W Voltage resolution 0.01 V Current resolution 0.001 A Capacity measuring range 0-9999.99 Ah Energy measuring range 0-9999.99 Wh Residual ripple 100 mV(pp) at maximal capacity Display 2.4 inch LCD Dimensions (housing) 172 x 86 x 310 mm Weight (incl. device, power supply and housing) 3 kg Included JT-RD6006 DC Power Supply Power Supply for JT-RD6006 (RD6006-NT) Large aluminium housing for JT-RD6006 (Case02) ESP-12F WiFi Module Downloads Datasheet JT-RD6006 Manual JT-RD6006 PC Software Windows driver Mac driver Linux driver

Read more less

The FNIRSI LCR-ST1 is a compact, multifunctional, and smart LCR tester that supports automatic measurements of resistance, capacitance, inductance, diode testing, and continuity. Its 1.14-inch color display combined with a convenient magnetic adsorption function enhances ease of use, while the built-in 250 mAh lithium battery ensures long-lasting performance. The device supports three frequency ranges (100 Hz, 1 kHz and 10 kHz) and offers 0.3 V and 0.6 V RMS test levels for versatile testing applications. The unique tweezer-shaped design of the LCR-ST1 is ideal for delicate tasks in confined spaces and enables fast and accurate testing of electronic components. Its light weight and portable design make it an invaluable tool for both field and laboratory use. Whether you are an experienced engineer or just starting out in electronics, the LCR-ST1 delivers reliable and accurate measurement results, allowing you to complete your tasks with greater efficiency and precision. Features Offers 3 test frequencies (100 Hz, 1 kHz, 10 kHz) and 2 test voltage levels. Features automatic component identification for faster and more reliable measurements. High-resolution 1.14-inch color display for clear readouts. Supports automatic data recording and storage. The tweezer tips are made from gold-plated brass for enhanced durability and conductivity. Specifications Resistance Range 10 mΩ – 10 MΩ Capacitance Range 1 pF – 22 mF Inductance Range 1 μh – 10 H Diode On voltage 0.7 V Frequency Test 100 Hz, 1k Hz, 10 KHz Level Test 0.3 V, 0.6 V RMS Parameter Display ESR, D value, Q value, Z value, X value Display 1.14" HD color screen Charging Interface USB-C, 5 V/1 A Power Supply Built-in 250 mAh lithium battery Auto Recognition Measurement Yes Replaceable Tweezer Head Yes Auto Shutdown Yes Data Hold Yes History Record Connect to PC to view and export Dimensions 28 x 19 x 150 mm Weight 41 g Included 1x LCR-ST1 SMD Tweezers 2x Hook Tips 1x Magnetic Patch 1x USB cable 1x Tool bag 1x Manual Downloads Manual Firmware V1.6

Read more less

ANT500 from Great Scott Gadgets is a telescopic antenna designed for operation from 75 MHz to 1 GHz. Its total length is configurable from 20 cm to 88 cm. ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. ANT500 is a 50 ohm general purpose antenna. It is the perfect first antenna for use with HackRF One.

Read more less

The FNIRSI HRM-10 is a portable, high-precision battery internal resistance and voltage tester. This device offers true four-wire measurement and is designed for both accuracy and ease of use. It automatically measures internal resistance and voltage values simultaneously, displaying the results on its HD color screen. Users have the option to manually adjust voltage and resistance ranges to suit their needs. The device also includes a sorting mode that automatically filters the good and bad batteries based on user-set thresholds. Additionally, it supports the storage of historical data and allows for exporting measurement records in table format. Features High Measurement Accuracy Tabular Data Export Auto-Evaluate Measurement Results 8 Threshold Settings HD Color Screen Folding Stand 1000 mAh Lithium Battery Specifications Voltage Resistance Measuring range 0-100 V (DC) 0-200 Ω Accuracy ±0.5% ±0.5% Gear Automatic, 1 V, 10 V, 100 V Automatic, 20 mΩ, 200 mΩ, 2 Ω, 20 Ω, 200 Ω Instrument test signal frequency 1 Khz (AC) Rechargeable USB-C (5 V/1 A) Built-in battery 1000 mAh lithium battery User calibration Yes Sorting mode Yes History record Yes Recorded data export Yes Working environment –10°C to +45°C, relative humidity <80% Storage environment –20°C to +80°C, relative humidity <80% Dimensions 158.7 x 80.5 x 28.4 mm Weight 225 g Included 1x FNIRSI HRM-10 Internal Resistance Tester 1x Clip Test Line 1x USB-C data cable 1x Manual Downloads Manual Firmware V0.3

Read more less

The FNIRSI DPOX180H is a cost-effective handheld dual-channel digital phosphor oscilloscope and signal generator. The oscilloscope has a real-time sampling rate of 500 MS/s and an analog bandwidth of 180 MHz. The measurement results are displayed on the high-contrast 2.8-inch IPS full-view LCD screen with digital fluorescence technology. Features 2-ch handheld oscilloscope & DDS signal generator 180 MHz bandwidth 500 MS/s sampling rate 20 MHz signal generator Innovative digital trigger system Cursor measurement function 5 mV sensitivity 50000 wfm/s waveform refresh rate 2.8" IPS full-vision high-definition display Built-in 4.2 V/3000 mAh lithium battery Automatic shutdown setting High-voltage anti-burning protection Specifications Nummer of channels 2 Analog bandwidth 180 MHz Maximum sampling rate 500 MS/s Input coupling DC/AC Rise time 2.5s Storage depth 120 Kpts Input impedance 1 MQ-18 PF Vertical sensitivity 5 mV-10 V (1X) Time base range 5 nS~50 S DC accuracy ±2% Time accuracy +0.01% Trigger detection Digital trigger Trigger mode Auto/Single/Normal Trigger edge Rising/Falling Measurement range 40 mV~80 V (1X) Screenshot storage 90 Capture signal 500 Screen size 2.8 inch Screen resolution 320 x 240 Display technology IPS full view Expansion interface USB transmission interface Auto power off 5 minutes - 2 hours Firmware upgrade Supported iso image upgrade Charging requirements 5 V/2 A Battery capacity 3000 mAh Standby time 3.5 hours at full charge Signal Generator 14 standard function signals Waveform storage 250 groups Parameter measurement 12 kinds Dimensions 135 x 90 x 40 mm Digital Phosphor Oscilloscope FNIRSI DPOX180H Oscilloscope uses the latest digital phosphor technology to overcome the traditional oscilloscope due to noise caused by the waveform burr feeling. Color temperature display function can more clearly see the distribution of the signal, probability characteristics and the rise and fall time of the step signal fast and slow. X-Y mode with digital phosphor technology for comparison of amplitude, frequency and phase of two groups of signals. DDS Function Signal Generator Built-in 20 MHz DDS function signal generator, with 14 kinds of standard function signals, output amplitude fixed at 1 VPP, sine wave frequency of 20 MHz, other waveform frequency of 10 MHz, adjustable frequency step of 1 Hz. Contains the original chopping technology, intercept part of the oscilloscope measurement of complex signals as the output signal of the signal generator, than the traditional signal generator hand-drawn signal more objective and realistic. Included 1x FNIRSI DPOX180H phosphor oscilloscope 2x Probes (200 MHz) 1x USB power supply 1x USB cable 1x Manual Downloads Manual Firmware V40

Read more less

The FNIRSI FNB58 USB tester (with Bluetooth) is a comprehensive and very accurate USB voltage and current meter. It features a 2.0-inch full-color HD TFT display, built-in USB-A, micro USB and USB-C interface. With this device you can measure the power supply or power consumption of products or the charging power of cell phones and power supplies. You can also determine the fast charging protocol of chargers. Features USB-A and USB-C interface 2.0" HD display Data at a glance Wide compatibility Ultra-precise data detection Play with fast charging technology Automatic protocol detection (PD2.0, 3.0, 3.1, PPS, QC2.0, 3.0, FCP, SCP, AFC, PE, DASH VOOC, SuperVOOC and more) Simple user interface, easy to operate 4 function curve displays (real-time voltage and current curve, offline curve recording, D+/D- voltage curve, high-speed power supply ripple measurement) Cable detection 10 groups of energy recording battery capacity calculation PC connectivity for data logging and firmware updates Bluetooth app for Android devices Specifications Voltage range 4-28 V Current range 0-7 A Power range 0-120 W Load equivalent internal resistance 0-9999.9 Ω D+/D- voltage 0-3.3 V Capacity 0-9999.99 Ah Power consumption 0-9999.99 Wh Cable resistance 0-9999.9 Ω Interfaces micro USB, USB-A, USB-C Dimensions 42 x 13 x 82 mm Downloads Manual Firmware V0.68

Read more less

The JOY-iT DMSO2D72 is your ideal companion for the workshop and outdoor use. It combines a 2-channel oscilloscope, a signal generator for any wave type as well as a multimeter with 6 different measurement types in one device and serves all functions you expect from individual devices. JOY-iT has placed particular emphasis on simple, clear and practical handling in order to make work as pleasant as possible for the user. For this the DMSOD72 is equipped with a 'one-button' auto measuring function and a 'one-button' page out. In addition, 2 signals can be compared directly on the 2.8' 65K colour LCD display. The power supply is provided by two 18650 lithium batteries, which are included in the scope of supply and allow a continuous operation of one day as well as a standby time of up to 8 weeks. Furthermore, operation via the USB-C interface is also possible, during which the batteries are charged simultaneously. In order to protect the device perfectly in 'outdoor use', the DMSO2D72 was equipped with a silicone sheath, which offers protection against shocks, dirt and heat. The extensive and very user-friendly software is available in English, German and French and can be switched easily on the device. You will also be impressed by the PC software, which provides you with a multitude of functions with very high ease of use. General Specifications Display type 2.8' 64K color TFT-LCD Display resolution 320 x 240 Display settings Adjustable background brightness, backlight duration, auto power off time Protective case Silicon cover, good impact resistance, outstanding heat resistance, easy to disassemble Special features Mobile use through battery operation, 3-in-1 device (oscilloscope, signal generator, multimeter), 3 languages (German, English, French) Assembly / Stand function 45° suspension bracket Interface USB Type C for power/data Rechargeable battery 2x 16850 Lithium Charging current 5 V / 2 A Battery life In use: A full dayIn standby: Up to 8 weeks PC software Windows 7 and higher Operating temperature 0-50°C Dimensions 199 x 98 x 40 mm Weight 624 g Oscilloscope Channels 2 + DMM + AWG Bandwidth 70 MHz Sampling Rate 250 MSa/s Single channel125 MSa/s Dual channel Vertical resolution 10 mV - 10 V Automatic measurement of Frequency and amplitude Manual cursor measurement Voltage and time Output impedance (DC) 25 pF ±3 pF; 1 MΩ ±2% Maximum input voltage 150 V RMS Signal Generator Sampling rate 250 MSa/s Vertical resolution 12 bits Waveforms Sine, square, triangle, trapezoid, and many more Sine 1 Hz - 25 MHz Square 1 Hz - 10 MHz Triangle 1 Hz - 1 MHz Trapezoid 1 Hz - 5 MHz Frequency resolution 1 Hz Output impedance 50 Ω Digital Multimeter 6 Multimeter measuring modes Voltage, current, resistance, capacity, diode, on-off Max. resolution 4000 Counts Ranges Voltage 0 µV - 600 V DC0 mV - 600 V AC, 40-400 Hz Current 0 µA - 10 A Resistance 0 mΩ - 40 MΩ Capacity 0 pF - 100 µF Diode 0-2 V On-off <50 Ω Included JOY-iT 3-in-1 Handheld DMSO2D72 2 rechargeable batteries (18650, 2600 mAh) Passive 80 MHz Probe + accessories 2x BNC to crocodile clip coaxial cable 2x DMM test lead USB to USB-C cable USB power supply (5 V, 2 A) Downloads Datasheet Manual PC Software 1.1.10 Flash Manual (28-07-2021) Flash Software Latest firmware version (13-01-2022)

Read more less

The FNIRSI DMC-100 is a high-precision 10,000-count True RMS clamp multimeter for engineering, labs, vehicle repairs, and home diagnostics. It measures up to 750 V and 600 A with three modes (routine, waveform, and power) along with NCV detection for added safety. Its 2.0-inch color TFT display offers clear readings, data visualization, and adjustable brightness. A 1500 mAh rechargeable battery with auto power-off ensures long use, while a flashlight, backlight, and data storage enhance usability, making it a reliable tool for professionals and DIYers. Features 10,000-count smart True RMS clamp meter for accurate readings Supports up to 750 V voltage and 600 A current 2.0-inch full-color TFT screen (240 x 320) for clear visuals New UI with data curve display for easy reading at a glance Switch freely between general measurement, waveform display, and power measurement modes Non-contact voltage measurement and zero/fire line identification Measures temperatures from −55°C to 1300°C Built-in battery (3.7 V/1500 mAh) for extended usage Convenient charging and data transmission via USB-C port Includes an LED light, screen backlight, and data-saving capabilities Intelligent automatic shutdown to conserve battery life Easily switch between temperature units (°C/°F) Screen brightness is adjustable for various environments Supports firmware updates to enhance functionality Specifications DC Voltage 9.999V/99.99V/999.9V ±(0.5%+3) AC Voltage 9.999V/99.99V/750.0V ±(1%+3) DC Current 99.99A/600.0A ±(2.5%+10) AC Current 99.99A/600.0A ±(2.5%+10) Resistance 9.999MΩ/999.9KΩ/99.99KΩ/9.999KΩ/999.9Ω ±(1.5%+3) 99.99MΩ ±(1.5%+3) Capacitance 999.9μF/99.99μF/9.999μF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Frequency 9.999MHz/999.9KHz/99.99KHz/9.999KHz/999.99Hz/99.99Hz/9.999Hz ±(0.1%+2) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Continuity Test Yes Diode Yes NCV Yes LIVE Yes Display 2.0" TFT Color Screen Power Supply 3.7 V/1500 mAh Lithium Battery Charging 5 V/1 A (USB-C) Maximum Jaw Size 25 mm Dimensions 193 x 74 x 32 mm Weight 194 g Included 1x FNIRSI DMC-100 Clamp Meter 1x Multimeter pen 1x Temperature probe 1x USB charging cable 1x Manual Downloads Manual Firmware V1.3

Read more less

The DSO3D12 is a portable dual-channel oscilloscope featuring a high-definition 3.2" display and a 120 MHz bandwidth, packed with powerful features. It integrates a high-precision True RMS multimeter that supports rapid software calibration. When measuring low voltage, resistance, or continuity, both the oscilloscope and multimeter functions can be used simultaneously. The built-in waveform generator can output various waveforms including sine, square, and triangle waves. The voltage amplitude is 2.5 V, the frequency is adjustable from 0 to 2 MHz, and the square wave duty cycle can be adjusted from 1% to 99%. Using MCU and FPGA chips, the DSO3D12 ensures high-speed signal acquisition and fast data processing, providing a smooth user experience with a wealth of functions. The DSO3D12 is widely used in various applications, including: Basic R&D Chip debugging Car repair and maintenance Home appliance repair DIY debugging Radio amateur activities Switching power supplies Frequency converters Welding machines Bus waveform analysis Crystal waveform analysis This versatility makes the DSO3D12 an invaluable tool for a wide range of technical and electronic tasks. Features Screen: 3.2" HD color display Bracket: Collapsible stand Key type: Soft silicone keys Charging: USB-C/5 V Built-in rechargeable battery for approx. 6 hours of operation Dimensions: 145 x 86 x 33 mm Weight: 266 g Specifications (Oscilloscope) Channels 2 Bandwidth 120 MHz (CH1 only)60 MHz (CH1+CH2) Sampling rate 250 MSa/s Equivalent sampling 500 M Rise time <3ns Storage 128 Kb Impedance 1 MΩ Time base 5ns - 10s Peak voltage ±400 V (10x) Trigger mode Auto/Normal/Single Triger type Rise/Fall Triger level Manual/Auto Triger source CH1/CH2 Display mode YT/XY/Roll Persistence None/1s/∞ Coupling AC/DC Auto mode OneKey auto/Fully auto Sensitivity X1: 10 mV/div~10 V/divX10: 100 mV/div~100 V/div Measure items 14 types DC offset ±2% XY mode Yes Screenshot Yes Frequency ±0.01% Zoom mode Yes FFT Yes Generator wave Sine/Square/Triangle Generator voltage 2.5 V ±0.05 Generator frequency 1 Hz~2 MHz Specifications (Multimeter) Function Range Precision DC Voltage 600 mV/6.00 V/60.0 V/600 V/750 V ±(0.5% +3) AC Voltage 600 mV/6.00 V/60.0 V/600 V ±(1% +3) DC Current 600 mA/10 A ±(2% +5) AC Current 600 mA/10 A ±(3% +5) Resistance 600.0 Ω ±(1.5% +3) 6.000 kΩ/60.00 kΩ/600.0 kΩ ±(1% +3) 6.000 MΩ ±(1.5% +5) 60.00 MΩ ±(3% +3) Capacitance 60.00 nF/600.0 nF/6.000 μF ±(10% +5) 60.00 μF/600.0 μF ±(15% +5) Diode 0.0~3.3 V, Display "OL" above 3.3 V Continuity Sound at 50 Ω and below Included 1x DSO3D12 Oscilloscope 2x P6100 oscilloscope probes 2x Test Leads 1x USB-C charging cable 1x Manual Downloads Manual

Read more less

The UT603 is a handheld digital inductance capacitance meter for testing resistors, capacitors and inductors. It can also be used to measure transistor parameters. This accurate meter (with 2000 counts) can be used to check electronic components in labs, production lines and maintenance facilities. Features Manual range Continuity buzzer Diode and transistor test Low battery indication Specifications Resistance (Ω) 200 Ω / 2 kΩ / 20 kΩ / 200 kΩ / 2 MΩ / 20 MΩ ±(0.8%+1) Capacitance (F) 2 nF / 20 nF / 200 nF / 2uF / 20 uF / 200 uF / 600uF ±(1%+5) Inductance (H) 2 mH / 20 mH / 200 mH / 2 H / 20 H ±(2%+8) Display counts 2000 Power 9 V battery (6F22) Display 61 x 32 mm Dimensions 172 x 83 x 38 mm Weight 312 g Included 1x UNI-T UT603 LCR meter 1x 9 V block battery 2x Test leads with alligator clips 1x Manual Downloads Manual Datasheet

Read more less

The DCA75 Pro is a great instrument that combines ease-of-use with amazing features. It can automatically identify a huge range of semiconductors, automatically identify pinouts and measure detailed parameters. Features Built-in graphics display (now backlit) to show detailed schematic of the component you're testing as well as pinout and measurement data USB connectivity to allow curve tracing, data storage/retrieval and device matching on your Windows PC (Windows 7 and higher) Single internal AAA alkaline cell for standalone operation Component Support Bipolar transistors (NPN/PNP inc Silicon/Germanium) Darlington transistors (NPN/PNP) Enhancement mode MOSFETs (N-Ch and P-Ch) Depletion mode MOSFETs (N-Ch and P-Ch) Junction FETs (N-Ch and P-Ch). Both symmetrical and asymmetrical types Enhancement IGBTs (N-Ch and P-Ch) Diodes and diode networks (2 and 3 lead types) Zener diodes (up to about 9 V) Voltage regulators (up to about 8 V) LEDs and bi-colour LEDs (2 lead and 3 lead types) Low power sensitive Triacs and Thyristors (<10 mA trigger and hold) Measurements BJT current gain (hFE) BJT base emitter voltage (Vbe) BJT collector leakage current MOSFET on and off gate threshold voltages MOSFET transconductance JFET pinch-off voltage JFET transconductance JFET IDSS (drain current for Vgs=0) IGBT on and off gate threshold voltages IGBT transconductance Voltage regulator output voltage Voltage regulator quiescent current consumption Voltage regulator drop-out voltage Zener voltage Diode forward voltage drop Specifications Analyzer type Semiconductor components Component detection Automatic Pinout detection Automatic, connect any way round Display type Graphic LCD (now backlit) Interface type USB for optional PC connection PC functions Curve tracing (Windows 7 and higher) Software Included on USB drive for Windows 7 and higher Battery Single AAA cell (supplied) Included Peak Atlas DCA75 Pro PC software on a USB Flash Drive for Windows 11, 10, 8, 7, XP Micro USB cable Fitted universal premium hook probes AAA Alkaline battery Downloads Datasheet (EN) User Guide (EN) User Guide (IT) Software Installation Guide (EN) Software and Firmware Package

Read more less

The FNIRSI SG-003A multi-functional Signal Generator a.k.a. Process Meter/Calibrator is a high-precision voltage/current generator and meter. The SG-003A provides highly accurate reference voltages or currents for testing and calibrating other measurement instruments like multimeters and oscilloscopes. Besides voltages and currents, the SG-003A also generates rectangular pulse signals with precisely programmable frequencies and duty cycles. Its converter mode turns the SG-003A into a precision voltage-controlled current source, or current-controlled voltage source, and even a voltage- or current-controlled frequency generator. The SG-003A is a great tool for checking your multimeter’s accuracy and precision, and for testing e.g. LEDs. Features Accuracy (voltage/current) 0.1% ±0.005 Resolution (current) 0.01 mA Frequency 0-10 kHz Resolution 5 digits Output power 24 V Display 2.4" TFT LCD (320 x 240) Dimensions 92 x 72 x 30 mm Weight 165 g Specifications Signal Range Precision Resolution Max load External power supply Active current output 0~24 mA ±(0.1% + 0.005) 0.01 mA 750 Ω Passive current output (XMT) 0~24 mA ±(0.1% + 0.005) 0.01 mA 0~30 V Voltage output 0~24 V ±(0.1% + 0.005) 0.01 V 24 V loop 0~24 mA ±(0.1% + 0.005) 0.01 mA Frequency output 0~9999 Hz ±2% 5 digits Current input 0~24 mA ±(0.1% + 0.005) 0.01 mA Voltage input 0~30 V ±(0.1% + 0.005) 0.01 V Included 1x FNIRSI SG-003A Signal generator 4x Test clips 1x USB charger 1x USB-C cable 1x Manual Downloads Manual Firmware V4.3

Read more less

The updated FNIRSI 2C53T, an enhanced version of its 10 MHz predecessor, is a compact and versatile 3-in-1 device. It combines a dual-channel 50 MHz oscilloscope, a 4.5-digit True RMS multimeter, and a signal generator with 13 waveform types, making it an essential tool for maintenance and research professionals. Oscilloscope: Features 50 MHz bandwidth, 250 MS/s sampling rate, ±400 V protection, FPGA + ARM + ADC architecture, and waveform saving for analysis. Multimeter: 4.5-digit True RMS with 19999 counts, supports AC/DC voltage, current, capacitance, resistance, diode, and continuity measurements. Signal Generator: Outputs 13 signal types up to 50 KHz, with adjustable frequency, amplitude, and duty cycle. With a 2.8-inch LCD, 3000 mAh battery (6-hour runtime), and a portable design, it delivers powerful functionality in a user-friendly package. Specifications Oscilloscope Channels 2 Analog Bandwidth 50 MHz Real-time Sampling Rate 250 MS/s Storage Depth 1 Kpts Impedance 1 MΩ Time Base Range 10ns-20s Vertical Sensitivity 10 mV/div-10 V/div (x1) Maximum Measured Voltage ±400 V Trigger Mode Auto/Normal/Single Trigger Type Rising edge, Falling edge Display Mode Y-T/Rolling/X-Y Coupling Method AC/DC Persistence OFF, 500ms, 1s, ∞ Math 8 Basic Operations + FFT Supported Waveform Screenshot Save, Export Waveform Image, Cursor Measurement, Infinite Afterglow Multimeter DC Voltage 1.9999V/19.999V/199.99V/1000V ±(0.5%+3) AC Voltage 1.9999V/19.999V/199.99V/750.0V ±(1%+3) DC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.2%+3) AC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.5%+3) Resistance 19.999MΩ/1.9999MΩ/199.99KΩ/19.999KΩ ±(0.5%+3) 1.9999KΩ/199.99Ω ±(2.0%+3) Capacitance 999.9uF/99.99uF/9.999uF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Continuity Test Yes Diode Yes Signal Generator 13 Signal Waveforms Sine wave, rectangular wave, sawtooth wave, half wave, full wave, positive step wave, reverse step wave, exponential rise, exponential fall, DC, multi-audio, Sinker pulse, Lorentz wave Output Frequency 0-50 KHz Output Amplitude 0-3 V Output Duty Cycle 0-100% General Display 2.8" HD color screen Resolution 320 x 240 Charging USB-C (5 V/1 A) Battery 3000 mAh Lithium battery Standby Time 6 hours Languages English, Chinese Dimensions 167 x 89 x 35 mm Weight 300 g Differences New vs Old Version Model 2C53T Upgrade 2C53T Predecessor Bandwidth 50 MHz 10 MHz Display Mode Y-T/Rolling/X-Y Y-T/Rolling Math 8 Basic Operations + FFT N/A Cursor Function Yes N/A XY Lissau Graph Yes N/A Afterglow Function Yes N/A Multimeter Accuracy 19999 Counts 9999 Counts Signal Generator 50 KHz 2 MHz Included 1x FNIRSI 2C53T Upgrade Oscilloscope (50 MHz) 2x P6100 Oscilloscope probes (10X) 1x Multimeter probe 1x Alligator clip probe 1x USB-C charging cable 1x Storage bag 1x Manual Downloads Manual Firmware V1.0.3

Read more less