With this 65 W USB-C PD power supply (with GaN technology) and the included USB-C cable you can start using the FNIRSI HS-01 soldering iron straight away. Of course, you can also use this charger to fast charge your tablets and smartphones via USB-C and USB-A. Included 65 W USB-C PD GaN Power Supply (EU) USB-C cable (1.2 m)

Read more less

WCH CH32V307 RISC-V development board features 8 UART ports controlled over Ethernet The CH32V307 is an interconnected microcontroller, based on 32-bit RISC-V core, with hardware stack area and fast interrupt entry. Compared with standard RISC-V, the interrupt response speed is greatly improved. With single-precision float point instruction sets added and stack area extended, the CH32V307 has higher performance, the number of U(S)ART is extended to 8, and the number of motor timer is extended to 4. The CH32V307 provides USB2.0 high-speed interface (480 Mbps) and has built-in PHY transceiver. Ethernet MAC is upgraded to GbE and integrates 10M PHY module. Features RISC-V4F processor, max 144 MHz system clock frequency Single-cycle multiplication and hardware division, hardware float point unit (FPU) 64KB SRAM, 256 KB Flash Supply voltage: 2.5 V/3.3 V, GPIO unit is supplied independently Multiple low-power modes: sleep/stop/standby Power-on/power-down reset (POR/PDR), programmable voltage detector (PVD) 2 general DMA controllers, 18 channels in total 4 amplifiers Single true random number generator (TRNG) 2x 12-bit DAC 2-unit 16-channel 12-bit ADC, 16-channel TouchKey 10 timers USB2.0 full-speed OTG interface USB2.0 high-speed host/device interface (built-in 480 Mbps PHY) 3 USARTs, 5 UARTs 2 CAN interfaces (2.0B active) SDIO interface, FSMC interface, DVP 2x I²C, 3x SPI, 2x I²S 80 I/O ports, can be mapped to 16 external interrupts CRC calculation unit, 96-bit unique chip ID Serial 2-wire debug interface Packages: LQFP64M, LQFP100 Downloads Datasheet GitHub

Read more less

The Peak Atlas ESR70 gold is an enhanced version of the previous Peak Atlas ESR70 Plus. It does everything that the ESR70 Plus did but better. It now measures capacitance up to 10x faster, and over a wider range, thanks to new test algorithms. The capacitance measurement is also much less influenced by parallel resistances or leakage current thanks to our new Triple-Slope measurement system. Using the supplied gold plated probes (removable), the Atlas ESR70 gold can measure ESR down to a resolution of 0.01 ohms, up to 40 ohms. It can even measure ESR for capacitors that are in-circuit. Probes are removable, allowing 2 mm compatible probes to be fitted. Audible alerts are produced for various ESR levels allowing you to perform many tests in succession without having to look at the display. The ESR70 automatically takes capacitive reactance into account, so even low value capacitors (down to 0.3 uF) can have the ESR measured accurately. Features Uses a single AAA Alkaline cell (included) Alphanumeric LCD with backlight Automatic analysis-start when you apply the probes Automatic capacitor discharge using controlled discharge function ESR (and low DC resistance) measurement (even in-circuit) Capacitive reactance automatically taken into account to ensure accurate ESR Capacitance measurement (if testing out-of-circuit) Audible alerts for various ESR levels Extended ESR measurement range up to 40 Ohms Optional probe alternatives easily fitted New gold Features Improved LCD with better backlight 10x faster capacitance measurement for large capacitors Enhanced user options system New triple-slope measurement system to vastly reduce the influence of parallel resistance and/or leakage current on capacitance measurements Much wider capacitance measurement range now 0.3 uF to 90,000 uF (was 1uF to 22,000uF) Specifications Analyzer type ESR and Capacitance Component types Capacitors (>0.3 uF) ESR range 0.00 Ohms to 40.0 Ohms ESR resolution From 0.01 Ohms In-circuit use ESR only Capacitance range 0.3 uF to 90000 uF Battery type 1.5 V Alkaline AAA Cell (supplied). Life typically 1500 ops Display type Alphanumeric LCD (with backlight) Included Peak Atlas ESR70 gold Extra-long and extra-flexible test cables (450 mm of Silicone covered cable) 2 mm gold plated plugs and sockets with removeable gold plated crocodile clips Comprehensive illustrated user guide AAA Alkaline cell Downloads Datasheet (EN) User Guide (EN) User Guide (FR) User Guide (IT)

Read more less

The Raspberry Pi Monitor is a 15.6-inch Full HD computer display. User-friendly, versatile, compact and affordable, it is the perfect desktop display companion for both Raspberry Pi computers and other devices. With built-in audio via two front-facing speakers, and VESA and screw mounting options as well as an integrated angle-adjustable stand, the Raspberry Pi Monitor is ideal for desktop use or for integration into projects and systems. It can be powered directly from a Raspberry Pi, or by a separate power supply. Features 15.6-inch full HD 1080p IPS display Integrated angle-adjustable stand Built-in audio via two front-facing speakers Audio out via 3.5 mm jack Full-size HDMI input VESA and screw mounting options Volume and brightness control buttons USB-C power cable Specifications Display Screen size: 15.6 inches, 16:9 ratio Panel type: IPS LCD with anti-glare coating Display resolution: 1920 x 1080 Color depth: 16.2M Brightness (typical): 250 nits Color gamut: 45% Viewing angle: 80° Power 1.5 A/5 V Can be powered directly from a Raspberry Pi USB port (max 60% brightness, 50% volume) or by a separate power supply (max 100% brightness, 100% volume) Connectivity Standard HDMI port (1.4 compliant) 3.5 mm stereo headphone jack USB-C (power in) Audio 2x 1.2 W integrated speakers Support for 44.1 kHz, 48 kHz, and 96 kHz sample rates Downloads Datasheet

Read more less

Features Product model: HW-818 Working voltage: DC 5V Product size: 27mm x 48.5 mm x 4.5 mm / 1.06” x 1.9” x 0.17” SPI Flash: Default 32Mbit RAM: Internal 520KB + External 4MPSRAM Bluetooth: Bluetooth 4.2 BR/EDR and BLE standards Wi-Fi: 802 II b/g/n/e/i Support interfaces: UART, SPI, I2C, PWM Supporting TF Card: Maximum Supporting 4G IO port: 9 Serial port rate: default 115200 BPS Image output format: JPEG (OV2640 only), BMP, GRAYSCALE Spectrum range: 2412-2484 MHz Antenna form: board PCB antenna, gain 2dBi Transmitting power: 802.l1b: 17 + 2dBm (1lMbps) 802.l1g:14+2dBm (54Mbps) 802.l1n:13+2dBm (MCS7)

Read more less

This RC522 RFID Kit includes a 13.56 MHz RF reader module that uses an RC522 IC and two S50 RFID cards to help you learn and add the 13.56 MHz RF transition to your project. The MF RC522 is a highly integrated transmission module for contactless communication at 13.56 MHz. RC522 supports ISO 14443A/MIFARE mode. The module uses SPI to communicate with microcontrollers. The open-hardware community already has a lot of projects exploiting the RC522 – RFID Communication, using Arduino. Features Operating Current: 13-26 mA/DC 3.3 V Idle Current: 10-13 mA/DC 3.3 V Sleep Current: <80 uA Peak Current: <30 mA Operating Frequency: 13.56 MHz Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, Mifare Pro, MIFARE DESFire Environmental Operating Temperature: -20-80 degrees Celsius Environmental Storage Temperature: -40-85 degrees Celsius Relative humidity: relative humidity 5% -95% Reader Distance: ≥50 mm/1.95' (Mifare 1) Module Size: 40×60 mm/1.57*2.34' Module interfaces SPI Parameter Data transfer rate: maximum 10 Mbit/s Included 1x RFID-RC522 Module 1x Standard S50 Blank Card 1x S50 special-shaped card (as shown by the keyring shape) 1x Straight Pin 1x Curved Pin Downloads Arduino Library MFRC522 Datasheet MFRC522_ANT Mifare S50

Read more less

Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi. It offers an IMX708 12-megapixel sensor with HDR, and features phase detection autofocus. Camera Module 3 is available in standard and wide-angle variants, both of which are available with or without an infrared cut filter. Camera Module 3 can be used to take full HD video as well as stills photographs, and features an HDR mode up to 3 megapixels. Its operation is fully supported by the libcamera library, including Camera Module 3’s rapid autofocus feature: this makes it easy for beginners to use, while offering plenty for advanced users. Camera Module 3 is compatible with all Raspberry Pi computers. All variants of Raspberry Pi Camera Module 3 feature: Back-illuminated and stacked CMOS 12-megapixel image sensor (Sony IMX708) High signal-to-noise ratio (SNR) Built-in 2D Dynamic Defect Pixel Correction (DPC) Phase Detection Autofocus (PDAF) for rapid autofocus QBC Re-mosaic function HDR mode (up to 3 megapixel output) CSI-2 serial data output 2-wire serial communication (supports I²C fast mode and fast-mode plus) 2-wire serial control of focus mechanism Specifications Sensor Sony IMX708 Resolution 11.9 MP Sensor size 7.4 mm sensor diagonal Pixel size 1.4 x 1.4 µm Horizontal/vertical 4608 x 2592 pixels Common video modes 1080p50, 720p100, 480p120 Output RAW10 IR cut filter Integrated in standard variants; not present in NoIR variants Autofocus system Phase Detection Autofocus Ribbon cable length 200 mm Cable connector 15 x 1 mm FPC Dimensions 25 x 24 x 11.5 mm (12.4 mm height for Wide variants) Variants of Raspberry Pi Camera Module 3 Camera Module 3 Camera Module 3 NoIR Camera Module 3 Wide Camera Module 3 Wide NoIR Focus range 10 cm - ∞ 10 cm - ∞ 5 cm - ∞ 5 cm - ∞ Focal length 4.74 mm 4.74 mm 2.75 mm 2.75 mm Diagonal field of view 75 degrees 75 degrees 120 degrees 120 degrees Horizontal field of view 66 degrees 66 degrees 102 degrees 102 degrees Vertical field of view 41 degrees 41 degrees 67 degrees 67 degrees Focal ratio (F-stop) F1.8 F1.8 F2.2 F2.2 Infrared-sensitive No Yes No Yes Downloads GitHub Documentation

Read more less

The TOPDON TC004 Lite thermal imaging camera combines simplicity with advanced features, making it ideal for both hobbyists and professionals. With a 160 x 120 pixel resolution, 1x/2x/4x zoom, and a wide 40° x 30° field of view, it delivers sharp and accurate thermal images. It operates across a broad temperature range (−20°C to +550°C), making it suitable for various industries like HVAC, electrical, and automotive diagnostics. Its lightweight design, 2.8” display, and 15-hour battery life ensure portability and uninterrupted use, providing a powerful tool for thorough thermal analysis. Features Wide Temp Ranging from −20°C to +550°C (−4°F to +1022°F) IR Photography 5 Color Palettes for More Possibilities Tripod Mountable for a Stable View High and Low Temperature Alarm Monitor Temperature Change with Waveform Graphs Long-lasting 15 Hour Battery Life Specifications TC004 TC004 SE TC004 Lite Display 2.8" Color TFT (320 x 240 Pixels) 2.8" Color TFT (320 x 240 Pixels) 2.8" Color TFT (320 x 240 Pixels) IR light resolution 256 x 192 Pixels 256 x 192 Pixels 160 x 120 Pixels Spectral range 8~14 μm 8~14 μm 8~14 μm FOV 52.5° x 39.5° 56° x 42° 40° x 30° Storage 2 GB RAM + 16 GB TF card 32 GB Built-in 512 MB Built-in Measuring range −20~350°C (−4~662°F) −20~550°C (−4~1022°F) −20~550°C (−4~1022°F) Temperature resolution 0.1°C (0.18°F) 0.1°C (0.18°F) 0.1°C (0.18°F) Measuring modes Center spot/hot spot/cold spot Center spot/hot spot/cold spot Center spot/hot spot/cold spot Measuring accuracy ±2°C or ±2% ±2°C or ±2% ±2°C or ±2% Frame rate 25 Hz 25 Hz 25 Hz Focal length 3.2 mm (0.12") 3.2 mm (0.12") 2.6 mm (0.1") NETD <40 mK <40 mK <40 mK Magnification 1x/2x/4x (digital zoom) 1x/2x/4x (digital zoom) 1x/2x/4x (digital zoom) Tripod screw hole Yes Yes Yes High/Low temperature alarm Yes Yes Yes LED flashlight Yes Yes No Video recording Yes Yes No Auto shutdown 5 min, 10 min, 20 min, OFF 5 min, 10 min, 20 min, OFF 5 min, 10 min, 20 min, OFF Battery Built-in 5000 mAh battery Built-in 5300 mAh battery Built-in 2900 mAh battery Charging time 4 h 4 h 4 h Standby time 12 h 16 h (High Brightness)21 h (Low Brightness) 15 h Operating system Standalone use/Windows devices Standalone use/Windows devices Standalone use PC-based analysis Supports image analysis with PC Yes No Dimensions 240 x 70 x 90 mm 240 x 70 x 90 mm 240 x 70 x 90 mm Weight 520 g 520 g 520 g Included 1x TOPDON TC004 Lite Thermal Imaging Camera 1x USB Power Supply 4x Plugs (EU, UK, US, and AU) 1x USB Cable 1x Storage Bag 1x Manual Downloads Datasheet Manual

Read more less

Aoyue Int 866 is a microprocessor-controlled 3-in-1 rework station designed to meet all your repair and soldering needs. It combines a hot air gun, a quartz IR preheater with external sensor and a soldering iron in one comprehensive package. This complete repairing system features digital control and display of hot air temperature, soldering iron temperature, air flow, and pre-heater temperature. With touch-type panel controls, you can achieve precision and ease of use in all your tasks. Both the hot air gun and the soldering iron temperatures can be digitally calibrated, ensuring accurate temperature settings for optimal performance. Features 550 W Hot Air Gun 550 W Pre-heater 60 W Soldering Iron Digital Temperature Display Integrated Hot Air Gun Platform Switchable Temperature Scale °C/°F User configurable 1 to 30 minute idle-to-auto-stand-by mode (with 30 minutes as default) for additional device protection and power saving Built-in auto-cooling process that protects the system and its components from excessive heat, prolonging usage life Compatibility with air nozzles of various types Wide selection of solder iron tips (T Series soldering tips) for different soldering requirements Specifications Hot Air Gun Power consumption 550 W Temperature range 100-480°C Heating element Metal heating core Pump type Centrifugal fan Soldering Iron Power consumption 60 W Output voltage 24 V Temperature range 200-480°C Heating element Ceramic heater Tip to ground resistance Below 2 Ω Tip to ground potential Below 2 mV Pre-heater Power consumption 550 W Temperature range 100-450°C Heating element Quartz crystal Heating area 130 x 130 mm Main Unit Power input 220 V Dimensions 192 x 100 x 325 mm Weight 6.55 kg Included 1x Int 866 Main Unit with Pre-heater and Hot Air Gun 1x Spare Hot Air Gun Heating Element 1x External Sensor 1x Hot Air Gun Mast with Wire Holder 1x 3-Segment Fully Articulating Arm Holder 1x Holder Stopper with Securing Screw 6x PCB Holder 7x PCB Holder Securing Screw 1x AT-9 Air Nozzle Set (T1194, T1195, T1198, BGA-S) 1x B016 Soldering Iron with Tip 1x Spare Soldering Iron Heating Element 10x Soldering Iron Tips (including T-0.5C, T-0.8C, T-0.8D, T-1C, T-1.2D, T-1.6D, T-2.4D, T-B, T-LB, T-I) 1x 2660 Soldering Iron Stand 1x Soldering Iron Stand Assembly guide 1x Vacuum Pen with 3 vacuum caps 1x Tool Box 1x G001 IC Popper 1x Power Cord 1x Instruction Manual

Read more less

Inspired by NASA's “Curiosity” and “Perseverance” Mars Rovers, this innovative M.A.R.S. Rover is an autonomous vehicle designed to drive around on rough terrain here on Earth. It uses the same rocker arm, bogey and differential arm mechanism. M.A.R.S. is an acronym for 'Mobile Autonomous Robotic System'. Features 6 Motors: 80 rpm 6 V, N20 micro gear motors 4 Servos: MG90S metal gear analog micro servos 4 FireLEDs Ultrasonic distance sensor on steerable mast Total number of special PCBs: 30 Number of different PCB designs: 11 Length: 200 mm Width: 185 mm Height with Mast: 170 mm Weight excluding Raspberry Pi Zero and batteries: 460 g There is a Python library module for the Raspberry Pi Zero that makes it easy to control the unit. Required Raspberry Pi Zero 4 rechargeable AA batteries Downloads Assembly of 4tronix M.A.R.S. Rover Kit Programming M.A.R.S. Rover on Raspberry Pi Zero Coding using Microsoft Makecode on GitHub

Read more less

With this device, you'll be able to automatically to detect NPN and PNP transistors, n-channel and p-channel MOSFETs, diodes, thyristors, resistors, capacitors and many other components. It is also possible to measure certain characteristics of these devices as, for example, the current amplification factor of BJT or the gate threshold voltage of a MOSFET and much more.Features Automatic detection of NPN and PNP transistors, n-channel and p-channel MOSFETs, diodes (including double diode), thyristors, resistor and capacitor and other components Automatic testing of the pins of a component, and displaying on the LCD Detection of the transistor, MOSFET protection diode amplification coefficient and the base to determine the emitter transistor forward biased voltage Measurement of the gate threshold voltage and the gate capacitance of the MOSFET Simultaneous measurement of the of two resistors while displaying resistor symbol Measurement of a single diode reverse capacitance Measurements of capacitance, resolution 1 pF Identification of Darlington transistors via the base-emitter threshold voltage and current amplification factor Measurement of the bipolar transistor current amplification factor and the base-emitter threshold voltage 2x16 Characters LCD-Display (12864 LCD with green backlight) Test ranges Resistance: Max. 50 MΩ, resolution 0.1 Ω Capacitance: 25 pF – 100000 µF Inductance: 0.01 mH – 20 H Specifications One-button operation Automatic shutdown for improved battery life Shutdown current less than 20 nA

Read more less

The PTS200 is a powerful, ESP32-controlled portable smart soldering iron with an adjustable output power range of 18 to 100 W. Paired with a 100-watt power supply and a 4-ohm soldering tip, this soldering iron eliminates the need for a traditional soldering station, fully meeting the demands of various soldering tasks. It features 4 adjustable operating voltages, allowing it to be configured for different power sources. Features 100 W Power Output: Experience rapid heating with a powerful 100 W output, reaching 450°C (842°F) in just 8 seconds for quick and efficient soldering. Universal Tip Compatibility: Compatible with T12/TS100/TS101 tips, making the PTS200 adaptable to a wide range of soldering tasks. Fast Charging Protocols: Supports PD3.0 and QC2.0/QC3.0, enabling power from fast charging adapters or power banks, ideal for soldering on the go. Automatic Sleep Function: Extends the lifespan of the soldering tips. The superfast wake-up feature ensures the soldering iron is always ready when needed. Ergonomic Design: Crafted with a CNC-machined metal body, the PTS200 offers both ergonomic comfort and reliable heat dissipation. Specifications Output Power 18-100 W Input Voltage (adjustable) • 9 V/2 A• 12 V/1.5 A• 15 V/3 A• 20 V/5 A Temperature Range 50-450°C (122-842°F) Heating Time 8 seconds Temperature Stability ±2% Microcontroller ESP32-S2 Display 0.96" OLED (128 x 64 pixels) Power Supply USB-C Special Features • Automatic sleep• CNC metal shell• Compatible with T12/TS101/TS100/Pinecil soldering tips• 20 V/5 A (100 W maximum power) Included PTS200 Soldering Iron Soldering tip BC2 (4 Ω) Soldering tip K (4 Ω) Soldering tip B2 (4 Ω) Soldering tip I (4 Ω) 100 W power supply (EU) USB-C cable Software Firmware

Read more less

The Raspberry Pi 400 offers a quad-core 64-bit processor, 4 GB RAM, wireless networking, dual-display output, 4K video playback, and a 40-pin GPIO header. It's a powerful, compact computer built into a portable keyboard. Specifications Processor Broadcom BCM2711 quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.8 GHz RAM 4 GB LPDDR4-3200 Connectivity Dual-band (2.4 GHz and 5.0 GHz) IEEE 802.11b/g/n/ac wireless LANBluetooth 5.0, BLEGigabit Ethernet2x USB 3.0 and 1x USB 2.0 ports GPIO Horizontal 40-pin GPIO header Video & Sound 2 × micro HDMI ports (supports up to 4Kp60) Multimedia H.265 (4Kp60 decode)H.264 (1080p60 decode, 1080p30 encode)OpenGL ES 3.0 graphics SD card support MicroSD card slot for operating system and data storage Keyboard US keyboard Power 5 V DC via USB connector Operating temperature 0°C to +40°C Dimensions 286 x 122 x 23 mm (maximum)

Read more less

Raspberry Pi Zero 2 WH is the successor to the breakthrough Raspberry Pi Zero W(H). The board incorporates a quad-core 64-bit Arm Cortex-A53 CPU, clocked at 1 GHz. At its heart is a Raspberry Pi RP3A0 system-in-package (SiP), integrating a Broadcom BCM2710A1 die with 512 MB of LPDDR2 SDRAM. The upgraded processor provides Raspberry Pi Zero 2 WH with 40% more single-threaded performance, and five times more multi-threaded performance, than the original single-core Raspberry Pi Zero. Features 64-bit quad-core processor VideoCore IV GPU 512 MB LPDDR2 DRAM 802.11b/g/n wireless LAN Bluetooth 4.2 / Bluetooth Low Energy (BLE) MicroSD card slot Mini HDMI and USB 2.0 OTG ports Micro USB power With mounted 40-pin header Composite video and reset pins via solder test points CSI camera connector Specifications SoC Broadcom BCM2710A1 CPU 64-bit ARM Cortex-A53 (4x 1 GHz) GPU Broadcom VideoCore VI RAM 512 MB LPDDR2 Wireless LAN 2.4 GHz IEEE 802.11b/g/n Bluetooth Bluetooth 4.2, BLE USB 1x micro USB (for data)1x micro USB (for power supply) GPIO HAT-compatible 40-pin GPIO header Video & Audio 1080P HD video & stereo audio via mini-HDMI connector SD card microSD (for operating system and storage) Power 5 VDC / 2.5 A (supplied via micro USB connector) Dimensions 65 x 30 x 5 mm Raspberry Pi Zero 2 WH is footprint-compatible with earlier Zero models.

Read more less

Miniware MHP50 is a super mini handheld SMD preheater with built-in cooling fan and user-friendly design, supporting heating curve function to achieve heating effect similar to reflow oven. With its square tower shape and detachable controller and heating plate design, you can put it in your pocket. The brass heating plate coated with nanoceramic ensures stable preheating performance. It is equipped with user-friendly features including preset temperature, tilt heating, power wake-up, auto sleep and easy-to-use firmware upgrade. The built-in OLED screen on the controller displays the parameters, and the RGB LED display with different colors makes it easy to control the current heating temperature. Features 5 x 5 cm heating area, 3.7 cm height, mini pocket size, suitable for mobile soldering application scenarios Separable controller and hot plate, flexible to replace Built-in high-speed cooling fan, which can automatically detect the temperature of the controller, intelligently adjust the fan speed, and accelerate heat dissipation Innovative air deflector to effectively cut off heat transferring, protecting controller from thermal damage 160 x 80 resolution color LCD display, clear and rich parameter display Built-in OLED display and true color LED, light color changes with heating temperature Hot plate adopts a futuristic design stainless steel bracket, artistic and practical Dual-mode power inputs: DC 5525 power jack for 19-24 V input upto 150 W; standard PD 20 V power input to reach 100 W Takes only 150 seconds at the fastest heating from room temperature (28°C) to 300°C (under DC 24 V power input) Innovative heating curve function, you can customize the heating temperature and duration by sections to achieve similar reflow soldering effect Multiple intelligent functions: preset temperature, overturn protection, brightness adjustment, firmware upgrade Ideal for preheating, desoldering circuit boards, components, etc. Specifications Model MPH50-B5 Hot plate material Brass with nano-ceramic coating (BS50) Screen Color LCD Heating area 50 x 50 mm Temperature range 100-350°C Temperature stability ±3% Power interface USB-CDC 5525 Input voltage DC 19-24 VPD 20 V (use only one input) Max power DC 5525 (150 W)PD 100 W Dimensions Controller: 71.5 x 55.5 x 22.5 mmHot plate: 50 x 50 x 29 mm Weight Controller: 78 gHot plate: 87 g Included 1x MHP50 Controller 1x BS50 Hot plate 1x PD cable (20 V/5 A) 1x Manual

Read more less

Now save €10 with this Starter Kit compared to buying them separately! This special Raspberry Pi 4 Starter Kit includes everything you need to get started right away with the world's most popular mini computer as a development and multimedia device. Kit Contents Raspberry Pi 4 B (4 GB RAM)The Raspberry Pi 4 is a complete computer system in a small package that provides multimedia and desktop performance comparable to an entry-level x86 PC system. Broadcom BCM2711 SoC 64-bit quad-core ARM Cortex-A72 (1.5 GHz) VideoCore VI @ 500 MHz 4 GB LPDDR4 SDRAM Gigabit Ethernet 802.11ac Wi-Fi Bluetooth 5.0 2x USB 3.0, 2x USB 2.0 and 1x USB-C (for power supply) 2x micro-HDMI (up to 4Kp60) 1x MicroSD (for storage) Official EU Power Supply (5.1 V, 3 A) for Raspberry Pi 4 (white)The official Raspberry Pi USB-C power supply (15.3 W) is designed specifically to power the Raspberry Pi 4. microSD Card (32 GB, Class 10) with SD Adapter (Pre-Installed with NOOBS)This microSD with pre-installed NOOBS (New Out Of Box Software) is an easy-to-use operating system installation manager for the Raspberry Pi. Official Case for Raspberry Pi 4 (white/red)This well-designed case protects the Raspberry Pi 4. Official HDMI Cable for Raspberry Pi 4 (white, 1 m)The official Raspberry Pi micro-HDMI to HDMI (A/M) cable (white, 1 m) is designed for the Raspberry Pi 4. Heatsink Set for Raspberry PiThese aluminum heatsinks cool the board and prevent the Raspberry Pi from overheating.

Read more less

ANT700 from Great Scott Gadgets is a lightweight telescopic antenna designed for operation from 300 MHz to 1100 MHz. Its total length is configurable from 9.5 cm to 24.5 cm. ANT700 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. ANT700 is a 50 ohm general purpose antenna. It is a perfect first antenna for use with HackRF One.

Read more less

With the PCW08G 9-piece tweezer set, you are well equipped to perform precision work on sensitive electronic components. The tweezers are made of coated stainless steel and are therefore particularly durable and resistant. The set is antistatic and ESD-safe, which means that the tweezers are ideal for working with electronic components, as they prevent electrostatic charges, thus avoiding damage to the components. With the set you get a storage bag, enabling you to safely store and transport your tweezers. So you always have everything ready to hand when you need it. Thanks to the different shapes and tip types of the tweezers, the set is ideal for a variety of applications, such as model making, jewelry making and watch repair. Even the smallest components can be easily gripped and positioned. Included ESD-10, straight tip ESD-11, straight tip ESD-12, straight tip ESD-14, straight tip ESD-16, straight tip ESD-13, flat round head ESD-15, 45° curved tip ESD-17, 30° curved tip ESD34A-sa, flat head Storage bag

Read more less

The GT-7U GPS module, with its high sensitivity, low power consumption, miniaturization, and its extremely high tracking sensitivity, delivers an extended area of coverage. In an area that the conventional GPS receiver would fail, such as narrow urban sky, dense Jungle environment, GT-7U can achieve high-precision positioning. Its compact size makes it suitable for applications in vehicles, mobile phones, video cameras, and other mobile positioning systems, and it is an excellent choice for GPS applications. Specifications Operating Frequency L1 (1575.42 ±10 MHz) Operating Voltage 3.3-5.2 V Operating Current Normal Mode: 50 mA Power-Saving Mode: 30 mA Communication Interface TTL serial port, microUSB interface Serial Port Baud Rate 9600 bps Communication format 8N1 Interface Logic Voltage 3.3 or 5 V External Antenna Inteface IPX Dimensions 22 x 21 x 5 mm Weight 8.5 g

Read more less

The Andonstar AD409 Max-ES boosts a high-quality metal lens and a unique UV filter design. Crafted from top-tier industrial-grade materials, it delivers unmatched precision and durability, ensuring a reliable product experience. The UV filter positioned in front of the metal lens blocks soldering heat, smoke, and dust, safeguarding the lens and making it perfect for soldering and maintenance professionals. The AD409 Max-ES features an oversized Max station (46 x 37 x 47.5 cm) and an advanced tool set, expanding the soldering station area by 370%. This upgrade meets the demands of professional soldering tasks and provides ample workspace for larger projects. The easy-to-use tool holder keeps tools within reach, ensuring they are always accessible. Additionally, the soldering helping hands with rotatable clamps simplify soldering and repair tasks, enhancing efficiency and convenience. The endoscope offers an all-around 360° view. This allows for clear observation of components from all sides and inside pipes, eliminating blind spots and ensuring thorough inspections. Features High-quality Metal Lens and Unique UV Filter Design New Max station Easy-to-use Tool Holder and Soldering Helping Hands Microscope with Endoscope All-around View 360° Professional HDMI Digital Microscope supports Multiple Output Methods 8 Levels adjustable LEDs Convenient Wireless Remote Control Specifications Screen size 10.1 inch (1280x800) Image sensor 4 MP Video output UHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps) Video format MP4 Magnification Up to 300 times (27 inch HDMI monitor) Photo resolution Max. 24 MP (5600x4200) Photo format JPG Focus range Min. 5 cm Frame Rate Max. 120fps Video interface HDMI Storage microSD card (up to 64 GB) PC support Windows, PC software with measurement Mobile phone, tablet terminal support Support WiFi connection and measurement Power source 5 V DC Light source 2 LEDs with the stand Endoscope Yes Stand size 46 x 37 x 47.5 cm (18.1 x 14.6 x 18.7") Included 1x Andonstar AD409 Max-ES Digital Microscope 1x Endoscope 1x Stand with 2 LEDs 1x UV filter (already assembled in the lens) 1x Soldering mat 1x Beam 1x Column 1x Tool holder 1x Soldering Helping Hands 1x Power adapter 1x Power cable 1x HDMI cable 1x USB cable 1x IR remote 1x Manual Downloads Manual Software

Read more less

Upgraded version II with Bluetooth function, larger battery capacity, built-in bandpass filter circuit and additional modes (HI-Z, LNA, 50 ohm) The ATS25 max-Decoder II is a portable, full-band MW/LW/SW/Ham/FM radio receiver based on the Si4732-A10 HF transceiver with DSP technology. The extremely compact and lightweight receiver has several built-in signal decoding modes including CW, RTTY, HELL, FT4, and FT8, making it an indispensable unit for radio amateurs. Features Rotary control or touch-screen user interface Automatic antenna input switching (BNC socket) Adjustable 500-6000 Hz bandwidth depending on modulation Real-time signal reception quality measurement and automatic search for radio stations based on received data 10 Hz minimum SSB frequency setting. 1 Hz BFO generator for precise tuning within ham radio bands RDS information decoding SSB reception Rapid frequency entry using two fast switching VFOs Unlimited station memory with grouping by reception range CB band channel mode Extensive setting and customization options Morse code decoding for Latin and Cyrillic alphabets DIGI modes decoding (RTTY, FELD-HELL, FT4, FT8) Decoded data saving, storage, and sending to a PC WiFi connectivity for updates and advanced decoding modes Updateable, ESP32-based, control software Supplied with preregistered licence key Specifications Display: 2.4-inch (net) color TFT with touch (320 x 240) Case material: aluminum alloy Built-in battery: 4000 mAh Lithium-ion (supports up to 6 hours of operation) Bluetooth Internal loudspeaker Headphones output (3.5 mm jack) VHF FM: 64-108 MHz with RDS MW: 520-1710 kHz LW: 153-500 kHz SW: 1730-30000 kHz Firmware version: 4.17 Air Power: USB-C Dimensions: 117 x 112 x 45 mm Weight: 380 g Included 1x ATS25 max-Decoder II Receiver 1x Wi-Fi antenna 1x Telescopic antenna 1x Stylus pen 1x USB-C charging/data cable 1x Dust cloth 1x Manual

Read more less