Oscilloscopes

DSO-TC3 combines a digital oscilloscope, electronic component tester, signal generator, continuity test, voltage test, temperature and humidity measurement, infrared decoding and other functions are skillfully integrated. It is equipped with a 2.4' color TFT display and a built-in rechargeable lithium battery for mobile use. Specifications (Oscilloscope) The oscilloscope has a real-time sampling rate of 10 MSa/s and a bandwidth of 500 kHz. With complete trigger function (single, normal, automatic), no matter if you’re using periodic analog signals or non-periodic digital signals. Maximum measured voltage signal is 400 V. Equipped with efficient AUTO, the measured waveform can be displayed without cumbersome adjustments. Real-time sample rate 10 MSa/s Bandwidth 500 khz Input resistance 1 MΩ Coupling method AC/DC Test voltage range 400 V Vertical Sensitivity (x1) 10 mV-10 V Horizontal time base range 1us-10s Trigger mode Auto/Normal/Single Trigger type Rising edge/Falling edge Waveform Freeze Yes Automatic measurement Yes Specifications (Component Tester) The instrument can automatically identify and measure various transistors, including NPN and PNP triodes, N-channel and P-channel mosfet, junction mosfet, diodes, dual diodes, thyristors, and resistors, inductors, capacitors and other passive components. Automatic detection of pin definition. Automatically analyze NEC protocol infrared code. Other functional modes: Including circuit continuity test, 0-40 V input voltage measurement, PWM output, 0-32 V regulated diode measurement, DS18B20 temperature sensor measurement, DHT11 temperature and humidity sensor measurement, etc. Specifications (Signal Generator) The signal generator has a total of 6 waveforms to choose from, with adjustable frequency and amplitude. Sine wave 1-100 KHz/0-3.3 V/50% Square wave 1-100 KHz/3.3 V/50% Pulse wave 1-100 KHz/3.3 V/0-100% Triangle wave 1-100 KHz/0-3.3 V/50% Ramp 1-100 KHz/0-3.3 V/0-100% DC 0-3.3 V Included 1x DSO-TC3 1x P6100 Oscilloscope Probe (100 MHz) 3x Test Hooks 1x Adapter 1x USB-C Cable 1x Original Manual by FNIRSI (English, Chinese, Russian, Portuguese) 1x Elektor Manual (English, French, German, Italian, Dutch) Downloads Original Manual Firmware v0.3

Read more less

The FNIRSI 2C23T is a fully functional, highly practical 3-in-1 dual channel digital oscilloscope with a high resolution 2.8-inch LCD display (320 x 240 pixels) designed for the maintenance and development industry. This device is equipped with 3 main functions: oscilloscope, multimeter and signal generator. The oscilloscope has an FPGA+MCU+ADC hardware architecture with a sampling rate of 50 MS/s, an analog bandwidth of 10 MHz and a built-in high-voltage protection module that supports the measurement of peak voltages of ±400 V maximum. The multimeter has a 4-digit 10000-point RMS value and supports AC/DC voltage and current measurements, as well as capacitance, resistance, diode, on/off and other measurement functions. Equipped with a built-in DDS function signal generator, it can output 7 kinds of function signals, with a maximum output of 2 MHz for all signals and a step of 1 Hz; the output frequency, amplitude and duty cycle are adjustable. The built-in 3000 mAh rechargeable lithium battery achieves a standby time of up to 6 hours. Features 2-ch oscilloscope 10 MHz bandwidth 50 MS/s real-time sampling rate 7 signal waveforms 10000 counts 2.8' HD color display (320 x 240 pixels) Dimensions: 167 x 89 x 35 mm Weight: 300 g Specifications Oscilloscope Dual channel, 2x 10 MHz bandwidth, 50 MS/s real-time sampling rate Maximum measured voltage: ±400 V FPGA+ADC+MCU high-performance hardware architecture, capturing waveform details without loss Equipped with complete triggering functions (auto, single, normal) Equipped with efficient automatic adjustment, the measured waveform can be displayed without complicated adjustment Save waveform screenshots, supports exporting images to a computer, facilitate secondary waveform analysis Multimeter 4-bit integer 9999 counting True RMS measurement Identification of voltage, current, capacitance, resistance, diode, on/off, and zero live wire Maximum input voltage: AC 750 V, DC 1000 V Automatic range, intelligent anti burning Data retention, color screen digital display Signal Generator 7 signal waveforms: sine wave, square wave, triangular wave, full wave, half wave, noise wave, DC Output frequency: 1 Hz-2 MHz Output amplituade: 0.1-3.3 V Output duty cycle: 0-100% Included 1x FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope 1x P6100 oscilloscope probes (10X) 1x Multimeter probe 1x Crocodile clip probe 1x USB-C charging cable 1x Original Manual by FNIRSI (English, German, Spanish, Portuguese, Russian, Chinese) 1x Elektor Manual (English, French, German, Dutch) Downloads Manual Firmware V2.0.2

Read more less

The FNIRSI DPOX180H is a cost-effective handheld dual-channel digital phosphor oscilloscope and signal generator. The oscilloscope has a real-time sampling rate of 500 MS/s and an analog bandwidth of 180 MHz. The measurement results are displayed on the high-contrast 2.8-inch IPS full-view LCD screen with digital fluorescence technology. Features 2-ch handheld oscilloscope & DDS signal generator 180 MHz bandwidth 500 MS/s sampling rate 20 MHz signal generator Innovative digital trigger system Cursor measurement function 5 mV sensitivity 50000 wfm/s waveform refresh rate 2.8' IPS full-vision high-definition display Built-in 4.2 V/3000 mAh lithium battery Automatic shutdown setting High-voltage anti-burning protection Specifications Nummer of channels 2 Analog bandwidth 180 MHz Maximum sampling rate 500 MS/s Input coupling DC/AC Rise time 2.5s Storage depth 120 Kpts Input impedance 1 MQ-18 PF Vertical sensitivity 5 mV-10 V (1X) Time base range 5 nS~50 S DC accuracy ±2% Time accuracy +0.01% Trigger detection Digital trigger Trigger mode Auto/Single/Normal Trigger edge Rising/Falling Measurement range 40 mV~80 V (1X) Screenshot storage 90 Capture signal 500 Screen size 2.8 inch Screen resolution 320 x 240 Display technology IPS full view Expansion interface USB transmission interface Auto power off 5 minutes - 2 hours Firmware upgrade Supported iso image upgrade Charging requirements 5 V/2 A Battery capacity 3000 mAh Standby time 3.5 hours at full charge Signal Generator 14 standard function signals Waveform storage 250 groups Parameter measurement 12 kinds Dimensions 135 x 90 x 40 mm Digital Phosphor Oscilloscope FNIRSI DPOX180H Oscilloscope uses the latest digital phosphor technology to overcome the traditional oscilloscope due to noise caused by the waveform burr feeling. Color temperature display function can more clearly see the distribution of the signal, probability characteristics and the rise and fall time of the step signal fast and slow. X-Y mode with digital phosphor technology for comparison of amplitude, frequency and phase of two groups of signals. DDS Function Signal Generator Built-in 20 MHz DDS function signal generator, with 14 kinds of standard function signals, output amplitude fixed at 1 VPP, sine wave frequency of 20 MHz, other waveform frequency of 10 MHz, adjustable frequency step of 1 Hz. Contains the original chopping technology, intercept part of the oscilloscope measurement of complex signals as the output signal of the signal generator, than the traditional signal generator hand-drawn signal more objective and realistic. Included 1x FNIRSI DPOX180H phosphor oscilloscope 2x Probes (200 MHz) 1x USB power supply 1x USB cable 1x Manual Downloads Manual Firmware V40

Read more less

The FNIRSI 1014D is a 2-in-1 oscilloscope and signal generator with comprehensive functions and high practicality. It is a cost-effective 2-channel desktop oscilloscope for the maintenance industry and R&D industry. The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. The built-in DDS signal generator supports 12 types of function signals. Specifications Channels 2 Display size 7 inch LCD LCD resolution 800 x 480 Bandwidth 100 MHz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50s ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X : 40V, 10X : 400V Cursor Position XY, Trigger Y Waveform storage 1000 pictures + 1000 waveforms Roll mode Yes One-button AUTO Yes Waveform manager Yes Capture output Yes Voltage accuracy ±5% Frequency precision ±0.01% high precision Parameter 12 kinds in total Generator 14 kinds in total Extension USB export Power supply 5 V/2 A, 3 A, 4 A Dimensions 310 x 145 x 70 mm Included 1x FNIRSI 1014D Oscilloscope 2x Oscilloscope probes (100 MHz) 1x USB charger 1x Manual Downloads User Guide

Read more less

The FNIRSI DSO152 is an extremely practical and cost-effective handheld oscilloscope with a real-time sampling rate of 2.5 MSa/s, a bandwidth of 200 kHz and complete trigger functions (single, normal and automatic). It can be used for both periodic analog signals and non-periodic digital signals and can measure voltages up to ±400 V. Equipped with an efficient one-key AUTO, it can display the measured waveform without cumbersome adjustments. It is equipped with a high-resolution 2.8-inch LCD screen with a resolution of 320x240 pixels and a built-in 1000 mAh high-quality lithium battery for up to 4 hours of operation. Specifications Sampling rate 2.5 MSa/s Bandwidth 200 kHz Vertical sensitivity 10 mV/DIV - 20 V/DIV (Progress according to the 1-2-5 way) Time base range 10µS/DIV - 50s/DIV (Progress according to the 1-2-5 way) Voltage range X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V) Trigger method Auto/Normal/Single Coupling method AC/DC Display 2.8' (320x240 pixels) USB charging 5 V/1 A Lithium battery capacity 1000 mAh Square wave calibration Frequency: 1K, Duty cycle: 50% Dimensions 99 x 68.3 x 19.5 mm Weight 100 g Included FNIRSI DSO152 Mini Oscilloscope Alligator clip probe USB cable Lanyard Manual Downloads Manual

Read more less

The FNIRSI 1013D is a fully featured 2-channel tablet oscilloscope with a high-resolution 7-inch LCD screen (800 x 480 pixels). The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. With full trigger functions (single/normal/automatic), it can be used for periodic analog signals or non-periodic digital signals. The built-in high-voltage protection module can withstand a continuous voltage of up to 400 V. Features Intelligent anti-burn,1X can withstand up to 400 V withstand voltage. 100 MHz analog bandwidth @ 1 GSa/s sampling rate (1X = 5 MHz,10X = 100 MHz). Fully fit 7-inch 800 x 480 resolution color TFT LCD display with bright colors and high contrast. Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation. High measurement voltage range, 1X can measure 0~40 V, 10X can measure 0~400 V,100X can measure 0~4000 V. Up to 12 parameters measurement: VPP, VP, Vmax, Vmin, Vavg, Vrms, Frequent, Duty+, Duty-, Time+, Time−, Period. Cursor measurement function, it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic). At any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO. One-button waveform storage and screenshot. Built-in 1 GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal. Built-in 6000 mAh rechargeable lithium battery, fully charged for 4 hours of continuous use at the highest screen brightness. Memory compression technology, waveform refresh screen does not flicker. Screen brightness adjustment. Background grid brightness adjustment. Applications Electronic DIY Appliance repair Car repair Equipment debug Scientific research Product development Specifications Channels 2 LCD size 7 inch LCD resolution 800 x 480 Display technology TFT Bandwidth 100 Mhz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50S ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X: 40 V, 10X: 400 V Cursor Position XY, Trigger Y Roll mode Yes One button AUTO Yes Waveform storage 1000 pictures + 1000 waveforms Waveform manager Yes Voltage accuracy ±2% Frequency precision ±0.01% high precision Parameter 12 kinds in total Battery 6000 mAh Lithium Standby 4 hours Extension USB export Power supply USB-C, 5 V @ 2 A/3 A/4 A Dimensions 184 x 124 x 50 mm Weight 650 g Included 1x FNIRSI 1013D 2-ch Tablet Oscilloscope 2x 100 MHz Probes (1X and 10X) 1x USB charger 1x USB cable 1x Manual Downloads Manual

Read more less