Elektor Labs Selection

This radiation survey meter can test electric field radiation and magnetic field emission to reach the optimal test result. It is used to test and learn electromagnetic radiation situations indoor and outdoor. It is equipped with a built-in electromagnetic radiation sensor, which can display the radiation value on the LCD after processing by the control microchip. You can make reasonable processing or taking effective prevention measures toward the electromagnetic radiation according to the test result. Features One detector for two uses, simultaneous detection of electric and magnetic field radiation Color-screen display Sound and light alarm, automatic alarm above safe value Press one button to lock radiation value (data lock) LCD graphic display of radiation value trend Radiation assessment, indicating if current radiation value is at safe level Easy to operate with one hand, move or perform on-site measurement Applications Electromagnetic radiation monitoring: House and apartment, office, outdoor and industrial site Electromagnetic radiation test: Mobile phone, computer, TV set, refrigerator and high voltage cable radiation test Radiation protection product test: Test effects of radiation-proof clothes, radiation-proof film and other prevention articles Specifications Electric field Magnetic field Unit V/m uT / mG Accuracy 1 V/m 0.01 uT/ 0.1 mG Range 1~1999 V/m 0.01~99.99 uT/ 0.1~999.9 mG Alarm threshold 40 V/m 0.4 uT/4 mG Reading display 3½ digit LCD Measurement bandwidth 5 Hz~3500 MHz Sampling time About 0.4s Measurement mode Dual mode at the same time Overload indication Maximum value of measurement range on LCD Operation temperature 0~50°C Operation humidity Relative humidity below 80% Working voltage 3.7 V Power 3.7 V Lithium battery Dimensions 61 x 25 x 134 mm Weight 131 g Downloads Manual

Read more less

This upgraded version (available exclusively from Elektor) contains the following improvements: Enhanced protective earthing (PE) for furnace chassis Extra thermal insulation layer around furnace to reduce odors The infrared IC heater T-962 is a microprocessor-controlled reflow oven that you can use for effectively soldering various SMD and BGA components. The whole soldering process can be completed automatically and it is very easy to use. This machine uses a powerful infrared emission and circulation of the hot air flow, so the temperature is being kept very accurate and evenly distributed. A windowed drawer is designed to hold the work-piece, and allows safe soldering techniques and the manipulation of SMDBGA and other small electronic parts mounted on a PCB assembly. The T-962 may be used to automatically rework solder to correct bad solder joints, remove/replace bad components and complete small engineering models or prototypes. Features Large infrared soldering area Effective soldering area: 180 x 235 mm; this increases the usage range of this machine drastically and makes it an economical investment. Choice of different soldering cycles Parameters of eight soldering cycles are pre defined and the entire soldering process can completed automatically from Preheat, Soak and Reflow through to cool down. Special heat up and temperature equalization with all designs Uses up to 800 Watts of energy efficient Infrared heating and air circulation to re-flow solder. Ergonomic design, practical and easily operated Good build quality but at the same time light weight and a small footprint allows the T-962 to be easily bench positioned transported or stored. Large number of available funtions The T-962 can solder most small parts of PCB boards, for example CHIP, SOP, PLCC, QFP, BGA etc. It is the ideal rework solution from single runs to on-demand small batch production. Specifications Max. soldering area 180 x 235 mm (7.1 x 9.3") Rated power 800 W Processing time 1~8 minutes Power supply 220 V AC/60 Hz Dimensions 31 x 29 x 17 cm (12.2 x 11.4 x 6.7") Weight 6.2 kg Downloads Manual GitHub

Read more less

This USB Logic Analyzer is an 8-channel logic analyzer with each input dual purposed for analog data recording. It is perfect for debugging and analyzing signals like I²C, UART, SPI, CAN and 1-Wire. It operates by sampling a digital input connected to a device under test (DUT) at a high sample rate. The connection to the PC is via USB. Specifications Channels 8 digital channels Maximum sampling rate 24 MHz Maximum input voltage 0 V ~ 5 V Operating temperature 0°C ~ 70°C Input impedance 1 MΩ || 10 pF Supported protocols I²C, SPI, UART, CAN, 1-Wire, etc. PC connection USB Dimensions 55 x 28 x 14 mm Included USB Logic Analyzer (8-ch, 24 MHz) USB Cable Jumper Wire Ribbon Cable Downloads Software

Read more less