Displays & LEDs
LILYGO LILYGO T-Display-S3 ESP32-S3 Development Board (with Headers)
LILYGO T-Display-S3 ESP32-S3 1.9-inch ST7789 LCD Display Development Board WiFi Bluetooth 5.0 Wireless Module 170x320 Resolution T-Display-S3 is a development board whose main control chip is ESP32-S3. It is equipped with a 1.9-inch LCD color screen and two programmable buttons. Communication using the I8080 interface Retains the same layout design as T-Display. You can directly use ESP32S3 for USB communication or programming. Specifications MCU ESP32-S3R8 Dual-core LX7 microprocessor Wireless Connectivity Wi-Fi 802.11, BLE 5 + BT Mesh Programming Platform Arduino IDE Micropython Flash 16 MB PSRAM 8 MB Bat voltage detection IO04 Onboard functions Boot + Reset + IO14 Button LCD 1.9' diagonal, Full-color TFT Display Drive Chip ST7789V Resolution 170(H)RGB x320(V) 8-Bit Parallel Interface Working power supply 3.3 V Support STEMMA QT / Qwiic Connector JST-GH 1.25 mm 2-pin Downloads Pinout GitHub
LILYGO LILYGO T-Display RP2040 Development Board
LILYGO T-Display RP2040 Raspberry Pi Module 1.14-inch LCD Development Board This board is based on a Raspberry Pi Pico RP2040 with Dual Cortex-M0+ and 4 MB Flash memory. It is equipped with a 1.14-inch full color IPS display. The ST7789V display has a resolution of 135 x 240 pixels and is connected via the SPI interface. Specifications MCU RP2040 Dual ARM Cortex M0+ Flash 4 MB Bus interfaces 2x UART, 2x SPI, 2x I²C, 6x PWM Programming language C/C++, MicroPython Support machine learning library TensorFlow Lite Onboard functions Buttons: IO06+IO07, battery power detection TFT Display 1.14-inch ST7789V IPS LCD Resolution 135 x 240, full color Interface 4-Wire SPI interface Operating temperature -20°C ~ +70°C Working power supply 3.3 V Connector JST-GH 1.25 mm 2-pin Included LILYGO T-Display RP2040 Unsoldered headers JST cable Downloads Pinout GitHub
€ 19,95
Members € 17,96
LILYGO LILYGO T-Beam V1.2 ESP32 LoRa Development Board with 0.96" Display (EU868)
This LILYGO T-Beam V1.2 ESP32 LoRa Development Board comes with pre-installed Meshtastic and soldered 0.96' display. The board has a built-in Semtech SX1262 LoRa transceiver and is equipped with a NEO-6M GPS receiver. GPS NEO-6M GPS module: Support GPS protocol Onboard RTC crystal: Support interrupt/wakeup LoRa Long Range Low Power LoRa Transceiver High sensitivity: -i48 dBm Transceive rate: 300 kbps Version: SX1276 (868 MHz) Firmware: Meshtastic Display OLED: 0.96 inch Driver: SSD1306 Specifications Microcontroller ESP32 Flash 4 MB PSRAM 8 MB Serial Chip CH9102 Wireless protocol Wi-Fi + Bluetooth 4.2 PMU AXP2101 Onboard functions 3 buttons (Power + IO38 + Reset) Power supply Micro USB, 18650 battery Antenna 3D WiFi Antenna LoRa antenna GPS ceramic antenna Included 1x LILYGO T-Beam V1.2 CH9102 1x 868 MHz Antenna 1x Soldered 0.96' LCD (128x64) 2x Pin headers Downloads GitHub Schematics
€ 49,95
Members € 44,96
