Search results for "mak"
Make makerdiary nRF52840 MDK USB Dongle incl. Case
The Makerdiary nRF52840 Dongle with Case is a small and low-cost development platform enabled by the nRF52840 multiprotocol SoC in a convenient USB dongle form factor. The USB Dongle is fully multiprotocol capable with full protocol concurrency. It has protocol support for Bluetooth 5, Bluetooth mesh, Thread, ZigBee, IEEE 802.15.4, ANT and 2.4 GHz proprietary stacks. Alternatively the USB Dongle can act as a Network Co-Processor (NCP) with a simple connection to a PC or other USB enabled device. Features Low cost USB dongle supporting Bluetooth 5, Bluetooth mesh, Thread, ZigBee, IEEE 802.15.4, ANT and 2.4 GHz proprietary stacks Shipped with USB enabled bootloader and OpenThread NCP firmware Programming via nRF Connect for Desktop or nRFUtil OpenThread Border Router supported Thread Network Sniffer with Wireshark Thread Topology Monitor Nordic nRF52840 System-on-Chip ARM Cortex-M4F processor optimized for ultra-low power operation Combining Bluetooth 5, Bluetooth Mesh, Thread, IEEE 802.15.4, ANT and 2.4 GHz proprietary On-chip USB 2.0 (Full speed) controller ARM TrustZone Cryptocell 310 security subsystem 1 MB FLASH and 256 kB RAM 1 user-programmable button 1 user-programmable RGB LED Integrated 2.4 GHz chip antenna Convenient USB dongle form factor Dimensions: 50.8 x 21.1 x 7.6 mm Weight: 6.0g Downloads Wiki
€ 29,95
Members € 26,96
Arduino Arduino Make-Your-Uno Kit
Learn the basics of electronics by assembling manually your Arduino Uno, become familiar with soldering by mounting every single component, and then unleash your creativity with the only kit that becomes a synth! The Arduino Make-Your-Uno kit is really the best way to learn how to solder. And when you are done, the packaging allows you to build a synth and make your music. A kit with all the components to build your very own Arduino Uno and audio synthesizer shield. The Make-Your-Uno kit comes with a complete set of instructions in a dedicated content platform. This includes video material, a 3D interactive viewer for following detailed instructions, and how to program your board once it is finished. This kit contains: Arduino Make-Your-Uno 1x Make-Your-Uno PCB 1x USB C Serial adapter Board 7x Resistors 1k Ohm 2x Resistors 10k Ohm 2x Resistors 1M Ohm 1x Diode (1N4007) 1x 16 MHz Crystal 4x Yellow LEDs 1x Green LED 1x Push-Button 1x MOSFET 1x LDO (3.3 V) 1x LDO (5 V) 3x Ceramic capacitors (22pF) 3x Electrolytic capacitors (47uF) 7x Polyester capacitors (100nF) 1x Socket for ATMega 328p 2x I/O Connectors 1x Connector header 6 pins 1x Barrel jack connector 1x ATmega 328p Microcontroller Arduino Audio Synth 1x Audio Synth PCB 1x Resistor 100k Ohm 1x Resistor 10 Ohm 1x Audio amplifier (LM386) 1x Ceramic capacitors (47nF) 1x Electrolytic capacitors (47uF) 1x Electrolytic capacitors (220uF) 1x Polyester capacitor (100nF) 4x connectors pin header 6x potentiometer 10k Ohm with plastic knobs Spare parts 2x Electrolytic capacitors (47uF) 2x Polyester capacitor (100nF) 2x Ceramic capacitors (22pF) 1x Push-Button 1x Yellow LEDs 1x Green LED Mechanical parts 5x Spacers 12 mm 11x Spacers 6 mm 5x screw nuts 2x screws 12 mm
€ 79,95
Members € 71,96
Makerfabs Makerfabs PN532 NFC Module V3
NFC is a popular technology in recent years. Almost all the high-end phones in the market support NFC. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. This module is built around NXP PN532. NXP PN532 is very popular in the NFC area. Makerfabs developed this module based on the official document. A library for this module is available. Features Small dimension and easy to embed into your project Support I²C, SPI, and HSU (High-Speed UART), easy to change between those modes Support RFID reading and writing, P2P communication with peers, NFC with Android phone Up to 5~7 cm reading distance On-board level shifter, Standard 5 V TTL for I²C and UART, 3.3 V TTL SPI Arduino compatible, plugin and play with our shield RFID reader/writer supports Mifare 1k, 4k, Ultralight, and DESFire cards ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX) Innovision Jewel cards such as IRT5001 cards FeliCa cards such as RCS_860 and RCS_854 Downloads Usage NFC Library
€ 12,95€ 8,95
Members identical
Elektor Classics Make Magazine 2020-2021 (USB-stick)
Het tijdschrift Make bevat bouwinstructies voor coole projecten (Arduino, Raspberry Pi en meer), die zowel door leken als gevorderden nagebouwd kunnen worden. Make laat niet alleen zien hoe het project werkt, maar publiceert ook basisartikelen, tutorials en informatieve reviews over bijvoorbeeld 3D-printers, oscilloscopen of soldeerbouten. Deze USB-stick bevat alle 10 gepubliceerde Make uitgaven van de jaargangen 2020 en 2021.
€ 49,95€ 14,95
Members identical
Makerfabs Makerfabs LoRa Soil Monitoring & Irrigation Kit (EU868)
This kit is based on ESP32 and LoRa. The ESP32 3.5' display is the console for the system, it receives the LoRa message from LoRa moisture sensors (support up to 8 sensors in the default firmware) , and send control commands to LoRa 4-channel MOSFET (2 4-channel MOSFET supported, with totally 8 channels), to control the connected valves open/close, and thus to control the irrigation for multiple points. Features Ready to use: Firmware are pre-programmed for all the modules before shipping, the user can only power them up and set the ID to the console, and start to use. Suitable for none-programmers, in 3 minutes to create filed application. With Lora wireless connection: The monitor & control range can be up to few kilometer, suitable for garden/small farm. Soil moisture sensor with good corrosion resistance, can be used at least half an year with 2 AAA battery. Easy to install: Compares to cheap solution with wires, which is hard to implement in files application, there the connection wires do not needed, the whole installation clean and easy; The valves can be connected Lora MOSFET easily. Hardware & Software Open: To study Lora & FreeRTOS. The ESP32 display console/Lora Soil Moisture Sensor/LoRa MOSFE are all programmed with Arduino. For programmers/engineers, can development further more specialized application. Based on ESP32, with WiFi connection, the console can also access to internet, the create much more applications including the moisture data updating to internet for remote monitor, and remote control with MQTT. Included 1x ESP32 3.5' Display (without camera) 1x Lora Expansion for ESP32 Display 2x Lora Moisture Sensor 1x Lora 4-channel MOSFET 1x 12 V Power Supply Water Pipe (5 m) 1x 1-input & 4-output Pipe Joint Downloads Instructable: Soil Monitoring & Irrigation with LoRa GitHub
€ 149,95
Members € 134,96
Makerfabs Makerfabs Jumper Wires Combo Pack
With these jumper wires (length: 20 cm) you can connect a Raspberry Pi or an Arduino with breadboards. Each cable consists of 40 individual wires/pins which can also be separated. Included 1x 40-pins female to female 1x 40-pins male to male 1x 40-pins male to female
€ 6,95
Members € 6,26
Makerfabs Makerfabs Acoustic Levitator DIY Kit
Included 76x 10 mm 40 kHz transducers 1x Arduino Nano 1x L298N Dual Motor Drive Board 1x Power Switch 1x DC Adaptor 9 V 1x Jumper Wires 6x Black and Red Wire Some Exposed Wire 1x 3D-Printed TinyLev Documents Instructables Scientific Information
€ 99,95
Members € 89,96
Makerfabs Makerfabs SenseLoRa Industrial-grade Air Monitor (EU868)
This air monitor is specifically used for monitoring greenhouses. It detects: Air temperature & Humidity CO2 concentration Light intensity Then transmit the data via LoRa P2P to the LoRa receiver (on your desk in the room) so that the user can monitor the field status or have it recorded for long-term analysis. This module monitors the greenhouse field status and sends all sensor data regularly via LoRa P2P in Jason format. This LoRa signal can be received by the Makerfabs LoRa receiver and thus displayed/recorded/analyzed on the PC. The monitoring name/data cycle can be set with a phone, so it can be easily implemented into the file. This air monitor is powered by an internal LiPo battery charged by a solar panel and can be used for at least 1 year with the default setting (cycle 1 hour). Features ESP32S3 module onboard with the WiFi and Bluetooth Ready to use: Power it on directly to use Module name/signal interval settable easily by phone IP68 water-proof Temperature: -40°C~80°C, ±0.3 Humidity: 0~100% moisture CO2: 0~1000 ppm Light intensity: 1-65535 lx Communication distance: Lora: >3 km 1000 mAh battery, charger IC onboard Solar panel 6 W, ensure system works Downloads Manual BH1750 Datasheet SGP30 Datasheet
€ 69,95
Members € 62,96
Makerfabs Makerfabs NFC Stickers (6 pcs)
Features NFC chip material: PET + Etching antenna Chip: NTAG216 (compatible with all NFC phones) Frequency: 13.56 MHz (High Frequency) Reading time: 1 - 2 ms Storage capacity: 888 bytes Read and write times: > 100,000 times Reading distance: 0 - 5 mm Data retention: > 10 years NFC chip size: Diameter 30 mm Non-contact, no friction, the failure rate is small, low maintenance costs Read rate, verification speed, which can effectively save time and improve efficiency Waterproof, dustproof, anti-vibration No power comes with an antenna, embedded encryption control logic, and communication logic circuit Included 1x NFC Stickers (6-color kit)
€ 9,95
Members € 8,96
Makerfabs Makerfabs 4G LTE Hat for Raspberry Pi
Use your Raspberry Pi with LTE Cat-4 4G/3G/2G Communication & GNSS Positioning, for remote data transmission/phone/SMS, suitable for remote area monitoring/alarming. This 4G hat is based on the Maduino Zero 4G LTE, but without any controller. It needs to work with Raspberry Pi (2x20 connector and USB). The Raspberry communicate with this HAT with simple AT commands(via the TX/RX Pins in the 2X20 connector) for simple controls, such as SMS/Phone/GNSS; with the USB connecting and proper Linux driver installed, the 4G hat act as a 4G network adapter, that can access to the Internet and transmit data with 4G protocol. Compares to normal USB 4G dongle, this Raspberry Pi 4G Hat has the following advantages: Onboard Audio codec, that you can have a call directly with your RPI, or auto broadcasting with a loudspeaker; Hardware UART communication, hardware controlling of Power(by 2s pulse of PI GPIO or POWERKEY button), hardware controlling of flight mode; Dual LTE 4G antenna, plus GPS antenna Features LTE Cat-4, with uplink rate 50 Mbps and downlink rate 150 Mbps GNSS Positioning Audio Driver NAU8810 Supports dial-up, phone, SMS, TCP, UDP, DTMF, HTTP, FTP, and so on Supports GPS, BeiDou, Glonass, LBS base station positioning SIM card slot, supports 1.8V/3V SIM card Onboard audio jack and audio decoder for making a telephone call 2x LED indicators, easy to monitor the working status Supports SIM application toolkit: SAT Class 3, GSM 11.14 Release 99, USAT Included 1x 4G LTE Hat For Raspberry Pi 1x GPS antenna 2x 4G LTE antenna 2x Standoff Downloads GitHub
€ 89,95€ 69,95
Members identical
Makerfabs Makerfabs DIY Thermal Camera ESP32S3 Display with MLX90640
This is a simple DIY kit using Makerfabs' ESP32-S3 3.5" Parallel TFT with Touch (320x480) and Mabee MLX90640 module to monitor the temperature and display on the screen or save to SD card. It is a nice tool for circuit testing and non-contact temperature sensing. Features Based on ESP32-S3, 3.5-inch TFT with capacitive touch Auto check the highest temperature point Temperature accuracy: <1°C Suitable for applications such as human temperature checking or electronic boards debugging All hardware & software are open, users can modify & add more functions, such WiFi/Bluetooth data transmitting Downloads Default firmware New remote monitoring firmware Blog
€ 79,95
Members € 71,96
Makerfabs Makerfabs 6 DOF Robot Arm with Raspberry Pi Pico
Raspberry Pi Pico is a great solution for servo control. With the hardware PIO, the Pico can control the servos by hardware, without usage of times/ interrupts, and limit the usage of the MCU. Driving the six servos on this robotic arm takes very little MCU capacity, so the MCU can deal with other tasks easily. This 6 DOF robotic arm is a handy tool for teaching and learning robotics and Pico usage. There are five MG996s (four are needed in the assembly and one for backup) and three 25-kg servos (two needed in the assembly and one for backup). Note that for the servos the angle ranges from 0° to 180°. All the servos need to be preset to 90° (with logic HIGH 1.5 ms duty) before the assembly to avoid servo damage during movement. This product includes all the necessary items needed to create a robotic arm based on Pico and Micropython. Included 1x Raspberry Pi Pico 1x Raspberry Pi Pico Servo Driver 1x Set '6 DOF Robot Arm' 1x 5 V/5 A Power Supply 2x Backup Servo Downloads GitHub Wiki Assembly Guide Assembly Video
€ 139,95
Members € 125,96