A fantastic dual instrument pack featuring the Atlas DCA Semiconductor Analyzer and the Atlas LCR Passive Component Analyzer. Housed in a robust padded case, complete with spare battery, user guide and space for accessories. The LCR40 (for Inductors, Capacitors and Resistors) is ideal for the hobbyist and professional alike. The DCA55 (for most semiconductors) provides fast component identification, pinout identification and wide component support. LCR40 Handheld LCR analyzer providing measurements for inductance, capacitance and resistance. The component type is automatically detected for you, just connect and press 'test'. The test frequency is automatically selected to provide the best measurement resolution. Test frequencies include DC, 1kHz, 15kHz and 200kHz. Inductance from 1uH to 10uH, minimum resolution of 1uH, typical accuracy of ±1.5% between 100uH and 100mH. Capacitance from 1pF to 10,000uF, minimum resolution of 1pF typical accuracy of ±1.5% between 200pF and 500nF. Resistance from 1R to 2MR, typical accuracy of ±1%. Test frequency is displayed with the measurement. Inductor DC resistance also displayed when testing inductors. Supplied with removable gold plated hook probes, battery and user guide. Compatible with standard 2mm test connectors. Not designed for in-circuit use. Automatic component type detection: Inductor, Capacitor or Resistor Automatic test frequency selection: DC, 1kHz, 15kHz and 200kHz Inductance from 1uH to 10H Capacitance from 1pF to 10,000uF Resistance from 1Ohm to 2MOhm Inductance measurement also shows DC winding resistance Test frequency displayed for all measurements Typical accuracy of 1.5% for inductors and capacitors (see spec table for details) Typical accuracy of 1% for resistors Test lead complete with gold plated 2mm plugs and sockets Supplied with removable gold plated hook probes DCA55 Connect any way round to automatically identify and measure a wide range of semiconductor devices. The DCA55 will automatically identify the type of the part, pinout and many component parameters. Components supported include bipolar NPN/PNP transistors, darlingtons, diode-protected transistors, transistors with built-in resistors, enhancement mode MOSFETs, depletion mode MOSFETs, diodes, diode networks, LEDs, 2 and 3 lead bicolour LEDs, JFETs and many more. Further measurements are displayed including transistor gain, leakage current, pn voltage drops, LED voltages, MOSFET threshold voltages and much more. Even if you don't know anything about the part, just connect it in any configuration and the DCA55 will identify the type of part for you and also identify all the leads. Supplied with universal gold plated hook probes, battery and illustrated user guide. Not designed for in-circuit testing. Automatic pinout detection and identification, connect any way round Automatic part type identification Supports semiconductors including transistors, MOSFETs, diodes, LEDs, JFETs and much more Detection of special component features such as transistors with diodes or transistors with built-in resistors Transistor gain measurement Transistor leakage measurement MOSFET gate threshold measurement Semiconductor voltage drop measurement Supplied with gold plated red/green/blue universal hook probes Included Peak Atlas LCR40 Automatic Passive Component Analyzer Peak Atlas DCA55 Semiconductor Analyzer Extra GP23 Battery Dual Carry Case

Read more less

Peak UTP05E is a comprehensive CAT 5/5e/6 network cable analyzer with superb accessories. Easy to use and very fast. Automatically identifies cable type (Straight through, cross-over, token ring etc) and verifies all the connections. Faults are clearly displayed and explained on screen. The Atlas IT will even instruct you on making up standard and special cables, complete with wire colors. Display type is alphanumeric LCD (not backlit). Features Automatic connection pattern recognition. Rapid assessment of all 8 wires within your cable. Identifies missing connections, shorted connections or incorrect connections. Will display the identity number of the 'identified' terminators to allow for easy testing and identification of multiple cable runs. Can display common cable colour codes to help you make up cables. Included UTP05 instrument. 2 miniature terminators to plug into another end of the cable run. 4 short patch cables to enable testing of patch panels and wall sockets. 24 miniature identified terminators, great for testing and identifying multiple cable runs. Pair of RJ11-to-RJ45 adapters to allow for easy testing of RJ11 based cabling. RJ45 to 8 x gold plated crocodile adapter for testing unterminated cables. Detailed printed user guide, complete with full-colour Ethernet wiring chart for common cable configurations. Alkaline battery installed and a spare alkaline battery. All supplied in a durable padded carry case. Specifications Category Cat 5, 5e, 6 (UTP) Connection type RJ45 plug or socket (RJ11 using supplied adapter set) Lines tested 8 lines (shielding not tested) Max. cable length 150 metres (500 feet) Test voltage ±5 V Test current ±2.5 mA Temperature range 10°C to 50°C (50°F to 122°F) Battery operating range 7 V to 13 V Battery type GP23, L1128, MN21, V23 (12 V Alkaline) Instrument dimensions 103 x 70 x 20 mm (4.1 x 2.8 x 0.8") Terminator dimensions 18 x 15 x 14 mm (0.7 x 0.6 x 0.6") Downloads Datasheet User Guide Common Ethernet Wiring Diagrams Avoid socket damage

Read more less

The UT381 light meter measures light intensity and displays the results in Lux or FC. It has a high sampling rate of 100/s. The low power consumption enables continuous operation of up to 200 hours. The results can be stored in the device and transferred to a PC for further analysis, printing and saving. Features Auto/manual range, data hold Auto power off (cancelable) MAX/MIN modes 2044 sets data storage Displays time and adjustable record intervals (0.5~255s) Restore to default mode Lux/FC selectable Specifications Illuminance measurement (Lux) 20 Lux ±(3%+20) 200 Lux ±(3%+8) 2000 Lux ±(3%+8) 20000 Lux ±(3%+8) Display count 2000 Data storage 2044 Auto power off approx. 10 minutes Low battery indication approx. ≤7.1 V Auto range √ Data hold √ MAX/MIN mode √ Real-time clock √ Auto record time setup √ USB interface √ Power 9 V battery (6LF22) Display 22.5 x 32.5 mm Dimensions 195 x 45 x 26 mm Weight 185 g Downloads Datasheet Manual

Read more less

The DE-5050 Insulation Tester is a versatile instrument designed for measuring insulation resistance, low resistance, and AC/DC voltage. Its user-friendly features make it suitable for various electrical testing applications. Features Offers five selectable test voltages for different test requirements Automatically detects AC/DC voltage and displays frequency when AC voltage exceeds 10 V Stores up to 100 sets of test results with date and time Switches off automatically after 10 minutes of inactivity Equipped with a backlit display Enables zero adjustment for low resistance measurements Automatic calculation and display of the Dielectric Absorption Ratio (DAR) and Polarization Index (PI) during the insulation resistance test Specifications Test Voltages 50 V, 100 V/125 V, 250 V, 500 V, 1000 V Insulation Resistance Range Up to 20 GΩ at 500 VUp to 40 GΩ at 1000 V Voltage Measurement Accuracy ±1%rdg±4dgt (sine wave) Dimensions 160 x 100 x 46 mm Weight 380 g (excluding batteries) Downloads Datasheet

Read more less

The PeakTech 5002 is a highly practical component tester designed for LEDs and various other electronic components. It delivers an automatically adjustable DC output voltage ranging from 0 to 300 V, adapting to the connected load to prevent damage to sensitive components. This makes it particularly well-suited for use in service and repair workshops. Features Output of automatic test voltage from 0 V to 300 V Suitable for testing individual LEDs or LED panels Suitable for testing the withstand voltage of electrolytic capacitors Suitable for Zener voltage testing of Zener diodes Safety: EN 61010-1 Specifications Input Voltage AC 100-240 V (Fuse: 2 A/250 V) Frequency 50-60 Hz Power consumption 10 W Output Voltage DC 0-300 V Accuracy ±5% +10 digts. Output Current <25 mA Dimensions 126 x 77 x 36 mm Weight 141 g Included 1x PeakTech 5002 LED Tester 2x Test leads 1x Power cable 1x Carrying case 1x Manual Downloads Datasheet (English/Deutsch) Datasheet (Italiano)

Read more less