This upgraded version (available exclusively from Elektor) contains the following improvements:
Enhanced protective earthing (PE) for furnace chassis
Extra thermal insulation layer around furnace to reduce odors
The infrared IC heater T-962 is a microprocessor-controlled reflow oven that you can use for effectively soldering various SMD and BGA components. The whole soldering process can be completed automatically and it is very easy to use. This machine uses a powerful infrared emission and circulation of the hot air flow, so the temperature is being kept very accurate and evenly distributed.
A windowed drawer is designed to hold the work-piece, and allows safe soldering techniques and the manipulation of SMDBGA and other small electronic parts mounted on a PCB assembly. The T-962 may be used to automatically rework solder to correct bad solder joints, remove/replace bad components and complete small engineering models or prototypes.
Features
Large infrared soldering area
Effective soldering area: 180 x 235 mm; this increases the usage range of this machine drastically and makes it an economical investment.
Choice of different soldering cycles
Parameters of eight soldering cycles are pre defined and the entire soldering process can completed automatically from Preheat, Soak and Reflow through to cool down.
Special heat up and temperature equalization with all designs
Uses up to 800 Watts of energy efficient Infrared heating and air circulation to re-flow solder.
Ergonomic design, practical and easily operated
Good build quality but at the same time light weight and a small footprint allows the T-962 to be easily bench positioned transported or stored.
Large number of available funtions
The T-962 can solder most small parts of PCB boards, for example CHIP, SOP, PLCC, QFP, BGA etc. It is the ideal rework solution from single runs to on-demand small batch production.
Specifications
Max. soldering area
180 x 235 mm (7.1 x 9.3")
Rated power
800 W
Processing time
1~8 minutes
Power supply
220 V AC/60 Hz
Dimensions
31 x 29 x 17 cm (12.2 x 11.4 x 6.7")
Weight
6.2 kg
Downloads
Manual
GitHub
When you see a Mendocino motor for the first time, you can't help but be fascinated. It floats in the air and spins by itself, seemingly without any source of energy. The functional principle is actually quite simple. The Mendocino motor is a magnetically levitating electric motor powered by solar energy. The solar panels supply current to the coils mounted on the shaft, which generates a magnetic field. The strong magnet attached to the base (the housing) provides a magnetic force that causes rotation. Thanks to the unique magnetic suspension, there is almost no friction. Make sure you have enough light! The stronger the light source, the faster it spins! Specifications Rotation speed 300-1,500 r/min Dimensions 5.31 x 2.76 x 2.76' (13.5 x 7 x 7 cm) Weight approx. 300 g
You've seen them online or in hilarious video's your colleagues sent you and now you can build one yourself, as a simple solderless kit! Including all you need except the batteries. Don't know it? There is a lot you can say about this kit, but actually all you need to do is watch a video and fall in love! A must have for each office!
Differences between micro:bit v1 and micro:bit v2 The BBC micro:bit v2 is equipped with BLE Bluetooth 5.0 It has a Power off button(push and hold power button) MEMS microphone with a LED indicator Onboard speaker Touch-sensitive logo pin LED power indicator A notched edge connector for easier connections.
The TV-B-Gone universal remote control allows you to turn virtually any TV On or OFF. You control when you see TV, rather than what you see. The TV-B-Gone Keychain remote is so small that it easily fits in your pocket so that you have it handy whenever you need it, wherever you go: bars, restaurants, laundromats, ballparks, arenas, etc.The TV-B-Gone Kit is a great way to teach about electronics. When soldered together, it allows you to turn off almost any television within 150 feet or more. It works on over 230 total power codes – 115 American/Asian and another 115 European codes. You can select which zone you want during kit assembly.This is an unassembled kit which means that soldering and assembly is required – but it’s very easy and a great introduction to soldering in general.This kit makes the popular TV-B-Gone remote more fun because you created it yourself with some basic soldering and assembly! Show your friends and family how technologically savvy you are, and entertain them with the power of the TV-B-Gone!The kit is powered by 2x AA batteries and the output comes from 2x narrow beam IR LEDs and 2x wide-beam IR LEDs.IncludedAll required parts/componentsRequiredTools, soldering iron, and batteriesDownloadsGitHub
The Mendocino Motor AR O-8 is a magnetically levitated, solar powered electric motor as a kit.Light Becomes MovementThe solar-powered Mendocino motor seems to float in the air. At first glance, you can't see why the rotor is turning at all. This is the magic of the motor.The Lorentz force is a very small electrical force. In a classroom setting, it is detected by a current swing in the magnetic field. With the Mendocino motor, we have succeeded in developing a beautiful application that uses this weak force for propulsion. Due to its concealed base magnet, the motor will fascinate technically inclined observers.In bright sunlight, the motor can reach a speed of up to 1,000 rpm. More impressive, however, is that even the faint glow of an ample tea light (D = 6 cm with a flame height of about 2 cm) is sufficient to drive the motor. The motor is not yet an alternative source of energy, even though it looks tempting. Presumably, it will remain an attractive model until a resourceful mind disproves this assumption.Dimensions
All solar cells 65 x 20 mm
Mirror diameter: 25 mm
Rotor weight: approx. 150 g
Model length: 160 mm
Model width: 85 mm
Frame height: approx. 85 mm
Frame material: black acrylic
Tube made of highly polished aluminum
Mirror color: silver
The Mendocino motor’s easy-to-follow instruction manual includes more than 70 illustrations. It describes a safe and practical approach to construction but also gives you the freedom to try your solutions.Partly Pre-Assembled KitA portion of the kit comes pre-assembled. Bonding the borosilicate glass pane to the acrylic surface requires specialized knowledge and aids. We do not want to impose this on the hobbyist. For instance, the base magnet is attached to the aluminum tube.As a hobbyist, you will need some know-how and appropriate tools: carpet knife, soldering iron and tin, hot glue, pliers, and a clamp or ferrule to fix the supplied assembly aid. A lot of fun is guaranteed!
Features Fully assembled and tested Nixie clock Six tested IN-14 Nixie tubes mounted to the clock base Two neon colon tubes installed into the clock base 12 V DC power adapter IR remote control Built-in proximity sensor User manual This clock is a combination of modern technologies and vintage Nixie tubes. It is a perfect gift for your friend and definitely will fit into any interior. Warm glowing of the neon will fill your house with soft orange light at night and will serve as a night light. The clock is built with 6 numeric IN-14 Nixie tubes. A built-in RGB LED backlight (with 10 levels for each channel) allow you to set your favorite color. Time accuracy is provided with built-in RTC (Real Time Clock DS3231) module and backuped with CR2032 battery while the clock is powered off. At the end of each minute (could be configured to be set from 1-5 minutes period or completely disabled) starts 'Slot Machine' feature that helps to prevent cathode poisoning effect. It scrolls over all numbers from 0 to 9. It is necessary to prolong tubes lifespan. Current date is shown each 1-5-th minute in 3 various formats: DD:MM:YY, MM:DD:YY or YY:MM:DD. The current time could be configured to 12 or 24 hour format. There are also three modes for colon tubes: Blinks once a second (is set as a default option) Permanently OFF Permanently ON The clock could be set to beep once an hour (when hour starts). The clock also has an alarm feature. All settings are stored in non-volatile memory (settings are restored after power-offs). Dimensions Height: 20 mm Width: 175 mm Length: 70 mm Tube height: 45 mm
Weatherproof (certified IP55) Fresnel IR lens to optimize motion detection Mount compatible with all models of Raspberry Pi (all A, B, and Zero models) Easy access to the Raspberry Pi’s internal components and ports Can be secured with a padlock Nylon camera attachment strap for securing outside Rear cable access Fasteners and spacers for attaching electronics No soldering required Rear attachments for modular upgrades Please note, you need to provide a Raspberry Pi.
Arduboy is a miniture game development system the size of a credit card based on the popular open source Arduino platform. Learn to program/code with lots of tutorials and an active community of developers, develop and share your own games using Arduino software via the USB-Cable. Use your PC/Mac/Linux machine to download over 200 unique games created by members of the Arduboy Community.Features
Processor: ATmega32u4 (same as Arduino Leonardo & Micro)
Memory: 32 KB Flash, 2.5 KB RAM, 1 KB EEPROM
Inputs: 6 Momentary Tactile Buttons
Outputs: 128 x 64 1-bit OLED, 4 Ch. Piezo Speaker & Blinky LED
Battery: 180 mAh Thin-Film Lithium Polymer
Connectivity: Micro-USB 2.0 with built-in HID profile
Programming: Arduino IDE, Arduboy Game Loader, GCC & AVRDude
Open source gamingAnyone can make games for the Arduboy! Free online tutorials guide you through a step by step process on how to develop your own software! There are already plenty of examples to learn from. Ever wanted to create a level or map for your favorite game, or make your favorite character jump higher? Now is your chance!Super retroDesigned to remind you of a more simple time in the world of gaming, the Arduboy brings true 8-bit gaming into the 21st century with style. The black and white screen invites you to involve your imagination once again while gaming.Durable constructionA polycarbonate front, ultra thin circuit board, and stamped aluminum metal back is the ultimate combination. A rechargeable lithium polymer battery provides over 8 hours of battery life, and the same cable you use to charge can be used to upload new games! At only 5 mm thick, Arduboy can live in your pocket (or even wallet) and is thinner than nearly any mobile phone!Downloads
Schematics
GitHub
Documentation
Do you need a simple AI camera to enhance your projects? The HuskyLens AI Camera intuitive design allows the user to control different aspects of the camera just by pressing buttons. You can start and stop learning new objects and even switch between algorithms from the device. To further reduce the need to be connected to a PC the HuskyLens AI Camera comes with a 2-inch display so you can see what's going on in real time. Specifications Processor: Kendryte K210 Image Sensor: OV2640 (2.0 Megapixel Camera) Supply Voltage: 3.3~5.0 V Current Consumption (TYP): 320 mA @ 3.3 V, 230 mA @ 5.0 V (face recognition mode; 80% backlight brightness; fill light off) Connection Interface: UART, I²C Display: 2.0-inch IPS screen with 320x240 resolution Built-in Algorithms: Face Recognition, Object Tracking, Object Recognition, Line Tracking, Color Recognition, Tag Recognition Dimension: 52 x 44.5 mm (2.05 x 1.75') Included 1x HuskyLens Mainboard 6x M3 Screws 6x M3 Nuts 1x Small Mounting Bracket 1x Heightening Bracket 1x Gravity 4-Pin Sensor Cable
Get started with microcontroller based electronicsThis Arduino-compatible bundle contains the Motherboard, Digitiser, Sensor Array and RGB Matrix. With these 4 boards you have everything you need to build a clock, score counter, timer, task reminder, thermometer, humidity display, sound meter, light meter, clap trigger, colored bar graph display, animated alarm, and much more!
The Motherboard has a built in real time clock module that keeps time even when unplugged.
The Digitiser can display 4 digits or characters and includes 2 buttons and a potentiometer to let you control what’s being displayed, or the brightness of the display.
The Sensor Array can read temperature, relative humidity, sound and light, with an SD card slot for data recording.
The RGB Matrix has 16 RGB LEDs that are controlled through shift registers, so only use 3 or 4 pins of the Motherboard.
MotherboardThe Motherboard is an Arduino-compatible microcontroller breakout board designed around the ATmega328P. The board comes in a solder-it-yourself kit with all the components you need to get started with microcontroller based electronics. All other boards connect to this.
Based on the ATmega328P
Arduino compatible
On-Board RTC (Real Time Clock)
FTDI Header for easy programming
Bluetooth Header
Terminal Block Connections
DigitiserThe Digitiser is a versatile display and input board. It let’s you visualise your data. Show your sensor information, clock digits, or even keep score for your favourite card game. The Digitiser also includes some buttons and a knob to let you take control.
4x 7-Segment Displays
Uses 595 Shift Registers
2 Switches and a Potentiometer
4 colored 'Mode' LEDs
Chainable with other 595 Boards
Terminal Block Connections
Sensor ArrayAs the name suggests, the Sensor Array is an array of sensors. Measure temperature and relative humidity via the DHT11, light via the light dependant resistor, and sound via the microphone and amplifier circuit. Then you can log the data using the on-board SD card slot.
DHT11 Temp & Humidity Sensor
Microphone and Amplifier Circuit
Light Dependent Resistor
MicroSD Slot for Saving Data
Logic Level Converter Circuit
Terminal Block Connections
RGB MatrixAdd color to your project by controlling 16 red, 16 green and 16 blue LEDs with just 3 pins of your microcontroller. The RGB Matrix uses shift registers, a matrix and switching transistors, so there’s plenty to learn and explore.
4x4 (16) RGB LEDs
Uses 595 Shift Registers
Chainable with other 595 Boards
Transistor Switches
Terminal Block Connections
Downloads (Manuals)
Motherboard
Digitiser
Sensor Array
RGB Matrix
This smart plinth lighting automatically switches on and off when you get up at night. The motion sensor sees you get out of bed and the light turns on! There is an illuminated path from bed to toilet. Obstacles on the way to the toilet are immediately visible and tripping hazards are prevented. Scientific research shows that the fear of falling is significantly reduced when using a Guide Light. The LED lighting has a perfect light intensity. The light is subtle enough not to wake you up, but bright enough for a reliable orientation. The Guiding Light is much more than just a night light.
This outdoor antenna made of fiberglass is optimized for the reception of ADS-B signals on the 1090 Mhz frequency. The antenna consists of a half-wave dipole with 5 dBi gain, encapsulated inside a fiberglass radome with an aluminum mounting base.
With a Raspberry Pi, an RTL-SDR and this antenna, you can receive position data from aircraft in your area for apps such as Flightradar24 or FlightAware.
Specifications
Frequency
1090 MHz
Antenna type
Dipole 1/2 wave
Connector
N female
Installation type
Mast Diam 35-60 mm (mounting bracket included)
Gain
5 dBi
SWR
≤1.5
Type of Polarization
Vertical
Maximum power
10 W
Impedance
50 Ohms
Dimensions
62.5 cm
Tube diameter
26 mm
Base antenna
32 mm
Operating temperature
-30°C to +60°C
Included
ADS-B antenna (1090 Mhz)
Mast bracket (for installation on a 35 to 60 mm diameter mast)
The iCEBreaker FPGA board is an open-source educational FPGA development board.
The iCEBreaker is great for classes and workshops teaching the use of the open source FPGA design flow through Yosys, nextpnr, IceStorm, Icarus Verilog, Amaranth HDL and others. This means the board is low cost and has a nice set of features to allow for the design of interesting classes and workshop exercises. At the same time it allows the user to use the proprietary vendor tools if they choose to.
After the workshop the boards can be easily used as a development board as most GPIO are exposed, broken out and configurable through jumpers on the back of the board. There is only a minimal amount of buttons and LED that can't be disconnected and used for your own purposes.
Documentation
Workshop
If you’re looking for a simple way to start soldering or just want to make your own Dasduino, this soldering set is a great opportunity. "Make your own Dasduino CORE" is an educational set for learning the skill of soldering, with which you end up with a functional microcontroller board. As with the other SMD versions of the Dasduino CORE boards we offer, the possibilities are endless.
It is based on the ATmega328P microcontroller, and all SMD components are already soldered on the board. The set also includes a THT socket for the microcontroller, which simplifies the replacement of the microcontroller should it ever become necessary.
Included
1x PCB
7x Capacitors (100nF)
4x Capacitors (2.2uF)
2x Capacitors (22pF)
5x Resistors (2.2 kOhm)
5x Resistors (10 kOhm)
3x Resistors (1 kOhm)
1x Resistor (100 kOhm)
1x Resistor (100 ohm)
1x JST battery connector
1x LED (purple)
1x LED (white)
1x LED (blue)
1x LED (red)
1x LED (orange)
1x Socket for ATmega328P
1x ATmega328P microcontroller
TurtleBot 4 is the next-generation of the world’s most popular open source robotics platform for education and research, offering better computing power, better sensors and a world class user experience at an affordable price point.TurtleBot 4 Lite is equipped with an iRobot Create 3 mobile base, a powerful Raspberry Pi 4 running ROS 2, OAK-D spatial AI stereo camera, 2D LiDAR and more. All components have been seamlessly integrated to deliver an out-of-the-box development and learning platform.Specifications
Base platform
iRobot Create 3
Wheels (Diameter)
72 mm
Ground Clearance
4.5 mm
On-board Computer
Raspberry Pi 4 (4 GB)
Maximum linear velocity
0.31 m/s in safe mode0.46 m/s without safe mode
Maximum angular velocity
1.90 rad/s
Maximum payload
9 kg
Operation time
2h 30m – 4h depending on load
Charging time
2h 30m
Lidar
RPLIDAR A1M8
Camera
OAK-D-Lite
User Power
VBAT @1.9 A5 V @ Low current3.3 V @ Low current
USB Expansion
2x USB 2.0 (Type A)2x USB 3.0 (Type A)
Programmable LEDs
Create 3 Lightring
Buttons and Switches
2x Create 3 User buttons1x Create 3 Power Button
Battery
26 Wh Lithium Ion (14.4 V nominal)
Charging Dock
Included
Size (L x W x H)
342 x 339 x 192 mm
Weight
3.3 kg
DownloadsUser Manual
The X-Carve CNC machine is great for Makers looking to start their CNC journey. Reliable, customizable, and expandable: X-Carve is also the best-selling machine for entrepreneurs and small businesses.
Start producing, no CNC knowledge required. X-Carve and Easel simplify 3D carving so you can begin working with wood, plastics and other materials in minutes.
Features
Carves wood, plastics, and materials like aluminum, Corian®️, and linoleum up to 37 inches wide.
Easy-to-follow assembly instructions will help familiarize you with your machine.
This model V2 is 3x faster, more rigid, and more accurate than the original X-Carve.
Design -> Carve -> Sell
Design: Sketch out your own idea and upload to Easel software, or browse from the library of over 3 million designs.
Carve: Easel controls the spindle and makes calculations so there's no guesswork.
Sell: X-Carve + Easel speeds up production so you can take on more jobs and get them out faster. The bundle pays for itself in no time.
Carvable Materials
Wood/Wood Composites: Hardwoods, softwoods, MDF, plywoods, etc.
Plastics: HDPE, Delrin®️, polycarbonate, acrylic, Corian®️, etc.
Non-Ferrous Metals: Aluminum, brass, copper, etc.
Import File Types: G-Code, SVG, or DXF files from any software
Software
Compatible with standard g-code and GRBL
1 Year of Easel Pro Included (world’s easiest CAD/CAM software)
Size & Weight
Work Area: 750 x 750 x 114 mm (29.5 x 29.5 x 4.5')
Machine Footprint: 1041 x 1321 x 559 mm (41 x 52 x 22')
Maximum Passthrough Sheet Width: 940 mm (37')
Finish: Anodized Aluminum
Product Weight: 45 kg
Shipping Weight: 50 kg
Included
X-Carve Base & Hardware
Rail Kit
DeWalt 26200 Spindle
X-Controller Kit
Nema 23 Motors Kit
Waste Board
Drag Chain
Toolkit
Homing Kit
Z-Probe Kit
Side Board
Dust Control System
Clamp Set
Digital Calipers
1 Year Easel Pro Software
Downloads
Instructions
Support
3D Models and Drawings
Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips. Features High Dynamics 17 km/h Intelligent Side-Follow System (ISS) Super Sensory System (SSS) 10-view Detection AI Detection, Human Recognition, etc. Flexible and adaptive Joints Long Endurance Specifications Light and Compact Weight: 12 kg Size (folded): 0.588 x 0.29 x 0.22 m High Performance Max Speed: 4.7 m/s (17 kmh or 10.6 mph) Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology) Robot dog can walk alongside its owner and not only follow The human-machine interaction is both harmonious and safe Super Sensory System Full View Coverage 5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors Lens Angle: 150 x 170° Built-in Powerful AI 16-core CPU + GPU (384 Cores, 1.5 TFLOPS) ISS and SSS Function Cooperatively Strong & Reliable Power System New Power Joint with Super Lightweight Low Noise and Long Life Heat Pipe Cooling System Built in the Knee Joint Motor Body/thigh joints: C1-8: 520 g 23.70N.m Knee Joint: C1-8 x 1.5 ratio 35.55N.m Unitree Go1 Variants The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard. Model Comparison Go1 Air Go1 Pro Go1 Edu Go1 Edu Plus SSS 1 Super-sensing system 1 set 5 sets 5 sets 5 sets Sensing calculation 1x (4x 1.43 GHz 128 Cores 0.5 T) 3x (4x 1.43 GHz 128 Cores 0.5 T) 3 Jetson Nano 2 Jetson Nano + 1 NVIDIA Jetson NX ISS 1 Intelligent Concomitant ✓ ✓ ✓ ✓ RTT 1 Pictures Transaction ✓ ✓ ✓ ✓ Charger 24 V, 4 V 24 V, 6 V 24 V, 6 V 24 V, 6 V Remote Control ✓ ✓ ✓ ✓ Load ≈3 kg ≈3 kg ≈5 kg (max ~10 kg) ≈5 kg (max ~10 kg) Heat Pipe Assisted Heat Dissipation ✓ ✓ ✓ ✓ Motion Speed 0~2.5 m/s 0~3.5 m/s 0~3.7 m/s (max ~5 m/s) 0~3.7 m/s (max ~5 m/s) Battery 1x 1x 1x 1x Graphical Programming Interface ✓ ✓ ✓ ✓ Scientific Programming Interface ✓ ✓ Python Programming Interface ✓ ✓ HAI 1 Human Sensing ✓ ✓ APP Top View ✓ ✓ ✓ 4G ✓ ✓ Foot-end Physical Force Sensor ✓ ✓ Multifunctional Peripheral Expansion Interface ✓ ✓ Radar 2D or 3D optional 2D or 3D optional Included 1x Unitree Go1 1x Unitree Go1 Battery 1x Unitree Go1 Charger 1x Unitree Go1 Remote Controller Downloads User Manual GitHub
Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips.
Features
High Dynamics 17 km/h
Intelligent Side-Follow System (ISS)
Super Sensory System (SSS) 10-view Detection
AI Detection, Human Recognition, etc.
Flexible and adaptive Joints
Long Endurance
Specifications
Light and Compact
Weight: 12 kg
Size (folded): 0.588 x 0.29 x 0.22 m
High Performance
Max Speed: 4.7 m/s (17 kmh or 10.6 mph)
Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology)
Robot dog can walk alongside its owner and not only follow
The human-machine interaction is both harmonious and safe
Super Sensory System
Full View Coverage
5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors
Lens Angle: 150 x 170°
Built-in Powerful AI
16-core CPU + GPU (384 Cores, 1.5 TFLOPS)
ISS and SSS Function Cooperatively
Strong & Reliable Power System
New Power Joint with Super Lightweight Low Noise and Long Life
Heat Pipe Cooling System Built in the Knee Joint Motor
Body/thigh joints: C1-8: 520 g 23.70N.m
Knee Joint: C1-8 x 1.5 ratio 35.55N.m
Unitree Go1 Variants
The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard.
Model Comparison
Go1 Air
Go1 Pro
Go1 Edu
Go1 Edu Plus
SSS 1 Super-sensing system
1 set
5 sets
5 sets
5 sets
Sensing calculation
1x (4x 1.43 GHz 128 Cores 0.5 T)
3x (4x 1.43 GHz 128 Cores 0.5 T)
3 Jetson Nano
2 Jetson Nano + 1 NVIDIA Jetson NX
ISS 1 Intelligent Concomitant
✓
✓
✓
✓
RTT 1 Pictures Transaction
✓
✓
✓
✓
Charger
24 V, 4 V
24 V, 6 V
24 V, 6 V
24 V, 6 V
Remote Control
✓
✓
✓
✓
Load
≈3 kg
≈3 kg
≈5 kg (max ~10 kg)
≈5 kg (max ~10 kg)
Heat Pipe Assisted Heat Dissipation
✓
✓
✓
✓
Motion Speed
0~2.5 m/s
0~3.5 m/s
0~3.7 m/s (max ~5 m/s)
0~3.7 m/s (max ~5 m/s)
Battery
1x
1x
1x
1x
Graphical Programming Interface
✓
✓
✓
✓
Scientific Programming Interface
✓
✓
Python Programming Interface
✓
✓
HAI 1 Human Sensing
✓
✓
APP Top View
✓
✓
✓
4G
✓
✓
Foot-end Physical Force Sensor
✓
✓
Multifunctional Peripheral Expansion Interface
✓
✓
Radar
2D or 3D optional
2D or 3D optional
Included
1x Unitree Go1
1x Unitree Go1 Battery
1x Unitree Go1 Charger
1x Unitree Go1 Remote Controller
Downloads
User Manual
GitHub
Unitree Go1 series consists of quadruped robots for the research & development of autonomous systems in the fields of human-robot interaction (HRI), SLAM & transportation. Due to the four legs, as well as the 12DOF, this robot can handle a variety of different terrains. The Go1 comes with a perfected drive & power management system, which enables a speed (depending on the version) of up to 3.7 m/s or 11.88 km/h with an operating time of up to 2.5 hours. Furthermore, the motors have a torque of 23.70N.m at the body/thighs and 35.55N.m at the knees, which also allow jumps or backflips.
Features
High Dynamics 17 km/h
Intelligent Side-Follow System (ISS)
Super Sensory System (SSS) 10-view Detection
AI Detection, Human Recognition, etc.
Flexible and adaptive Joints
Long Endurance
Specifications
Light and Compact
Weight: 12 kg
Size (folded): 0.588 x 0.29 x 0.22 m
High Performance
Max Speed: 4.7 m/s (17 kmh or 10.6 mph)
Intelligent Side Follow System (Adopt Patented Wireless Vector Positioning and Control Technology)
Robot dog can walk alongside its owner and not only follow
The human-machine interaction is both harmonious and safe
Super Sensory System
Full View Coverage
5 Sets Fish-Eye Stereo Depth Cameras + AI Post-processing + 3 Sets of Hypersonic Sensors
Lens Angle: 150 x 170°
Built-in Powerful AI
16-core CPU + GPU (384 Cores, 1.5 TFLOPS)
ISS and SSS Function Cooperatively
Strong & Reliable Power System
New Power Joint with Super Lightweight Low Noise and Long Life
Heat Pipe Cooling System Built in the Knee Joint Motor
Body/thigh joints: C1-8: 520 g 23.70N.m
Knee Joint: C1-8 x 1.5 ratio 35.55N.m
Unitree Go1 Variants
The Go1 series has 3 variants (Go1 Air, Go1 Pro and Go1 Edu), which differ a little technically. The differences are mainly the processors and sensor systems, the Air and Pro variant works, depending on the model, with one or 3x (4x 1.43 GHz 128 Cores 0.5 T) processor as well as with 1 or 5 super sensor systems. Both variants are equipped with 3 ultrasonic sensors. The Go1 Edu variant has up to 3 nano processors, 5 super sensor systems, and 4 ultrasonic sensors. In contrast, Edu Plus is equipped with an Nvidia Jetson Xavier NX as standard.
Model Comparison
Go1 Air
Go1 Pro
Go1 Edu
Go1 Edu Plus
SSS 1 Super-sensing system
1 set
5 sets
5 sets
5 sets
Sensing calculation
1x (4x 1.43 GHz 128 Cores 0.5 T)
3x (4x 1.43 GHz 128 Cores 0.5 T)
3 Jetson Nano
2 Jetson Nano + 1 NVIDIA Jetson NX
ISS 1 Intelligent Concomitant
✓
✓
✓
✓
RTT 1 Pictures Transaction
✓
✓
✓
✓
Charger
24 V, 4 V
24 V, 6 V
24 V, 6 V
24 V, 6 V
Remote Control
✓
✓
✓
✓
Load
≈3 kg
≈3 kg
≈5 kg (max ~10 kg)
≈5 kg (max ~10 kg)
Heat Pipe Assisted Heat Dissipation
✓
✓
✓
✓
Motion Speed
0~2.5 m/s
0~3.5 m/s
0~3.7 m/s (max ~5 m/s)
0~3.7 m/s (max ~5 m/s)
Battery
1x
1x
1x
1x
Graphical Programming Interface
✓
✓
✓
✓
Scientific Programming Interface
✓
✓
Python Programming Interface
✓
✓
HAI 1 Human Sensing
✓
✓
APP Top View
✓
✓
✓
4G
✓
✓
Foot-end Physical Force Sensor
✓
✓
Multifunctional Peripheral Expansion Interface
✓
✓
Radar
2D or 3D optional
2D or 3D optional
Included
1x Unitree Go1
1x Unitree Go1 Battery
1x Unitree Go1 Charger
1x Unitree Go1 Remote Controller
Downloads
User Manual
GitHub
This category offers a wide spectrum of platforms to choose from. They all have different features and you can choose the platform that best suits your needs or project.
