Arduino Boards

26 products


  • Arduino Uno R4 WiFi

    Arduino Arduino Uno R4 WiFi

    The Arduino Uno R4 is powered by the Renesas RA4M1 32-bit ARM Cortex-M4 processor, providing a significant boost in processing power, memory, and functionality. The WiFi version comes with an ESP32-S3 WiFi module in addition to the RA4M1, expanding creative opportunities for makers and engineers. The Uno R4 Minima is an affordable option for those who don't need the additional features. The Arduino Uno R4 runs at 48 MHz, which provides a 3x increase over the popular Uno R3. Additionally, SRAM has been upgraded from 2 kB to 32 kB, and flash memory from 32 kB to 256 kB to support more complex projects. Responding to community feedback, the USB port is now USB-C, and the maximum power supply voltage has been raised to 24 V with an enhanced thermal design. The board includes a CAN bus and an SPI port, enabling users to reduce wiring and perform parallel tasks by connecting multiple shields. A 12-bit analog DAC is also provided on the board. The Arduino Uno R4 comes in 2 versions (Minima and WiFi) and offers the following new features compared to the Uno R3: Arduino Uno R4 Minima Arduino Uno R4 WiFi USB-C connector USB-C connector RA4M1 from Renesas (Cortex-M4) RA4M1 from Renesas (Cortex-M4) HID device (emulate a mouse or a keyboard) HID device (emulate a mouse or a keyboard) Improved power section (up to 24 V through VIN) Improved power section (up to 24 V through VIN) CAN bus CAN bus DAC (12 bits) DAC (12 bits) Op amp Op amp WiFi/Bluetooth LE Fully-addressable LED matrix (12x8) Qwiic I²C connector RTC (with support for a buffer battery) Runtime errors diagnostics Model Comparison Uno R3 Uno R4 Minima Uno R4 WiFi Microcontroller Microchip ATmega328P (8-bit AVR RISC) Renesas RA4M1 (32-bit ARM Cortex-M4) Renesas RA4M1 (32-bit ARM Cortex-M4) Operating Voltage 5 V 5 V 5 V Input Voltage 6-20 V 6-24 V 6-24 V Digital I/O Pins 14 14 14 PWM Digital I/O Pins 6 6 6 Analog Input Pins 6 6 6 DC Current per I/O Pin 20 mA 8 mA 8 mA Clock Speed 16 MHz 48 Mhz 48 Mhz Flash Memory 32 KB 256 KB 256 KB SRAM 2 KB 32 KB 32 KB USB USB-B USB-C USB-C DAC (12 bit) – 1 1 SPI 1 2 2 I²C 1 2 2 CAN – 1 1 Op amp – 1 1 SWD – 1 1 RTC – – 1 Qwiic I²C connector – – 1 LED Matrix – – 12x8 (96 red LEDs) LED_BUILTIN 13 13 13 Dimensions 68.6 x 53.4 mm 68.9 x 53.4 mm 68.9 x 53.4 mm Downloads Datasheet Schematics

    € 29,95

    Members identical

  • Arduino Uno Rev3

    Arduino Arduino Uno Rev3

    Arduino Uno is an open-source microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator (CSTCE16M0V53-R0), a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. You can tinker with your Uno without worring too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again. 'Uno' means one in Italian and was chosen to mark the release of Arduino Software (IDE) 1.0. The Uno board and version 1.0 of Arduino Software (IDE) were the reference versions of Arduino, now evolved to newer releases. The Uno board is the first in a series of USB Arduino boards, and the reference model for the Arduino platform; for an extensive list of current, past or outdated boards see the Arduino index of boards. Specifications Microcontroller ATmega328P Operating Voltage 5 V Input Voltage (recommended) 7-12 V Input Voltage (limit) 6-20 V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328P) EEPROM 1 KB (ATmega328P) Clock Speed 16 MHz LED_BUILTIN 13 Dimensions 68.6 x 53.4 mm Weight 25 g

    € 24,95

    Members identical

  • Arduino Nano RP2040 Connect met Headers

    Arduino Arduino Nano RP2040 Connect with Headers

    The Arduino Nano RP2040 Connect is an RP2040-based Arduino board equipped with Wi-Fi (802.11b/g/n) and Bluetooth 4.2. Besides wireless connectivity the board comes with a microphone for sound and voice activation and a six-axis smart motion sensor with AI capabilities. An RGB LED is available too. 22 GPIO ports (20 with PWM support and eight analogue inputs) let the user control e.g. relays, motors and LEDs and read switches and other sensors. Program memory is plentiful with 16 MB of flash memory, more than enough room for storing many webpages or other data. Technical Specifications Microcontroller Raspberry Pi RP2040 USB connector Micro USB Pins Built-in LED pins 13 Digital I/O pins 20 Analog Input pins 8 PWM pins 20 (Except A6, A7) External interrupts 20 (Except A6, A7) Connectivity Wi-Fi Nina W102 uBlox module Bluetooth Nina W102 uBlox module Secure element ATECC608A-MAHDA-T Crypto IC Sensors IMU LSM6DSOXTR (6-axis) Microphone MP34DT05 Communication UART Yes I²C Yes SPI Yes Power Circuit operating voltage 3.3 V Input Voltage (VIN) 5-21 V DC Current per I/O pin 4 mA Clock speed Processor 133 MHz Memory AT25SF128A-MHB-T 16 MB Flash IC Nina W102 uBlox module 448 KB ROM, 520 KB SRAM, 16 MB Flash Dimensions 45 x 18 mm Weight 6 g Downloads Schematics Pinout Datasheet

    € 29,95

    Members € 26,96

  • Arduino Uno R4 Minima

    Arduino Arduino Uno R4 Minima

    The Arduino Uno R4 is powered by the Renesas RA4M1 32-bit ARM Cortex-M4 processor, providing a significant boost in processing power, memory, and functionality. The WiFi version comes with an ESP32-S3 WiFi module in addition to the RA4M1, expanding creative opportunities for makers and engineers. The Uno R4 Minima is an affordable option for those who don't need the additional features. The Arduino Uno R4 runs at 48 MHz, which provides a 3x increase over the popular Uno R3. Additionally, SRAM has been upgraded from 2 kB to 32 kB, and flash memory from 32 kB to 256 kB to support more complex projects. Responding to community feedback, the USB port is now USB-C, and the maximum power supply voltage has been raised to 24 V with an enhanced thermal design. The board includes a CAN bus and an SPI port, enabling users to reduce wiring and perform parallel tasks by connecting multiple shields. A 12-bit analog DAC is also provided on the board. The Arduino Uno R4 comes in 2 versions (Minima and WiFi) and offers the following new features compared to the Uno R3: Arduino Uno R4 Minima Arduino Uno R4 WiFi USB-C connector USB-C connector RA4M1 from Renesas (Cortex-M4) RA4M1 from Renesas (Cortex-M4) HID device (emulate a mouse or a keyboard) HID device (emulate a mouse or a keyboard) Improved power section (up to 24 V through VIN) Improved power section (up to 24 V through VIN) CAN bus CAN bus DAC (12 bits) DAC (12 bits) Op amp Op amp WiFi/Bluetooth LE Fully-addressable LED matrix (12x8) Qwiic I²C connector RTC (with support for a buffer battery) Runtime errors diagnostics Model Comparison Uno R3 Uno R4 Minima Uno R4 WiFi Microcontroller Microchip ATmega328P (8-bit AVR RISC) Renesas RA4M1 (32-bit ARM Cortex-M4) Renesas RA4M1 (32-bit ARM Cortex-M4) Operating Voltage 5 V 5 V 5 V Input Voltage 6-20 V 6-24 V 6-24 V Digital I/O Pins 14 14 14 PWM Digital I/O Pins 6 6 6 Analog Input Pins 6 6 6 DC Current per I/O Pin 20 mA 8 mA 8 mA Clock Speed 16 MHz 48 Mhz 48 Mhz Flash Memory 32 KB 256 KB 256 KB SRAM 2 KB 32 KB 32 KB USB USB-B USB-C USB-C DAC (12 bit) – 1 1 SPI 1 2 2 I²C 1 2 2 CAN – 1 1 Op amp – 1 1 SWD – 1 1 RTC – – 1 Qwiic I²C connector – – 1 LED Matrix – – 12x8 (96 red LEDs) LED_BUILTIN 13 13 13 Dimensions 68.6 x 53.4 mm 68.9 x 53.4 mm 68.9 x 53.4 mm Downloads Datasheet Schematics

    € 19,95

    Members identical

  • Arduino Giga R1 WiFi

    Arduino Arduino Giga R1 WiFi

    The Arduino Giga R1 WiFi brings the power of the STM32H7 to the same form factor as the popular Mega and Due, being the first Mega board to include onboard Wi-Fi and Bluetooth connectivity. The board provides 76 digital inputs/outputs (12 with PWM capability), 14 analog inputs and 2 analog outputs (DAC) all easily accessible via pin headers. The STM32 microprocessor with dual-core Cortex-M7 and Cortex-M4, together with onboard memory and audio jack enables you to perform machine learning and signal processing on the edge. Microcontroller (STM32H747XI) This dual core 32-bits microcontroller allows you have two brain talking to each other (a Cortex-M7 at 480 MHz and a Cortex-M4 at 240 MHz) you can even run micropython in one and Arduino in the other. Wireless communication (Murata 1DX) Whether you prefer Wi-Fi or Bluetooth, the Giga R1 WiFi got you covered. You can even quickly connect to the Arduino IoT Cloud and keep track of your project remotely. And if you are concerned about the security of the communication, the ATECC608A keeps everything under control. Hardware ports and communication Following the legacy of the Arduino Mega and the Arduino Due, the Giga R1 WiFi has 4x UARTs (hardware serial ports), 3x I²C ports (1 more than its predecessors), 2x SPI ports (1 more than its predecessors), 1x FDCAN. GPIOs and extra pins By keeping the same form factor of the Mega and the Due, you can easily adapt your custom made shields to the Giga R1 WiFi (remember this board works at 3.3 V though!). Also, additional headers have been added so that the total number of GPIO pins is now 76, and two new pins have been added: a VRTC so you can connect a battery to keep the RTC running while the board is off and an OFF pin so you can shut down the board. Connectors The Giga R1 WiFi has extra connectors on board which will facilitate the creation of your project without any extra hardware. This board has: USB-A connector suitable for hosting USB sticks, other mass storage devices and HID devices such as keyboard or mouse. 3.5 mm input-output jack connected to DAC0, DAC1 and A7. USB-C to power and program the board, as well as simulate an HID device such as mouse or keyboard. Jtag connector, 2x5 1.27 mm. 20-pin Arducam camera connector. Higher voltage support: In comparison with its predecessors that support up to 12 V, the Giga R1 WiFi can handle a range of 6 to 24 V. Specifications Microcontroller STM32H747XI dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet) Radio Module Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth (datasheet) Secure Element ATECC608A-MAHDA-T (datasheet) USB USB-C Programming Port / HID USB-A Host (enable with PA_15) Pins Digital I/O pins 76 Analog input pins 12 DAC 2 (DAC0/DAC1) PWM pins 12 Misc VRT & OFF pin Communication UART 4x I²C 3x SPI 2x CAN Yes (requires an external transceiver) Connectors Camera I²C + D54-D67 Display D1N, D0N, D1P, D0P, CKN, CKP + D68-D75 Audio Jack DAC0, DAC1, A7 Power Circuit operating voltage 3.3 V Input voltage (VIN) 6-24 V DC Current per I/O Pin 8 mA Clock Speed Cortex-M7 480 MHz Cortex-M4 240 MHz Memory STM32H747XI 2 MB Flash, 1 MB RAM Dimensions 53 x 101 mm Downloads Datasheet Schematics Pinout

    € 89,95

    Members € 80,96

  • Arduino Nano

    Arduino Arduino Nano

    The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x). It has more or less the same functionality of the Arduino Duemilanove but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one. The Nano was designed and is being produced by Gravitech. Specifications Microcontroller ATmega328 Operating Voltage (logic level) 5 V Input Voltage (recommended) 7-12 V Input Voltage (limits) 6-20 V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 8 DC Current per I/O Pin 40 mA Flash Memory 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader SRAM 1 KB (ATmega168) or 2 KB (ATmega328) EEPROM 512 bytes (ATmega168) or 1 KB (ATmega328) Clock Speed 16 MHz Dimensions 0.73 x 1.70' (18 x 45 mm) Power The Arduino Nano can be powered via the Mini-B USB connection, 6-20 V unregulated external power supply (pin 30), or 5 V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source. Memory The ATmega168 has 16 KB of flash memory for storing code (of which 2 KB is used for the bootloader), 1 KB of SRAM and 512 bytes of EEPROM The ATmega328 has 32 KB of flash memory for storing code, (also with 2 KB used for the bootloader), 2 KB of SRAM and 1 KB of EEPROM. Input and Output Each of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 V. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. Communication The Arduino Nano has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega168 and ATmega328 provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1). A SoftwareSerial library allows for serial communication on any of the Nano's digital pins. Programming The Arduino Nano can be programmed with the Arduino software (download). The ATmega168 or ATmega328 on the Arduino Nano comes with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files). You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see these instructions for details. Automatic (Software) Reset Rather than requiring a physical press of the reset button before an upload, the Arduino Nano is designed in a way that allows it to be reset by software running on a connected computer. One of the hardware flow control lines (DTR) of theFT232RL is connected to the reset line of the ATmega168 or ATmega328 via a 100 nF capacitor. When this line is asserted (taken low), the reset line drops long enough to reset the chip. The Arduino software uses this capability to allow you to upload code by simply pressing the upload button in the Arduino environment. This means that the bootloader can have a shorter timeout, as the lowering of DTR can be well-coordinated with the start of the upload.

    € 22,95

    Members € 20,66

  • Arduino Nano Every met Headers

    Arduino Arduino Nano Every with Headers

    Out of stock

    The Arduino Nano Every is an evolution of the traditional Arduino Nano board but features a lot more powerful processor, the ATMega4809. This will allow you to make larger programs than with the Arduino Uno (it has 50% more program memory), and with a lot more variables (the RAM is 200% bigger). An Improved Arduino Nano If you used Arduino Nano in your projects in the past, the Nano Every is a pin-equivalent substitute. The main differences are a better processor and a micro-USB connector. The board comes in two options: with or without headers, allowing you to embed the Nano Every inside any kind of invention, including wearables. The board comes with tessellated connectors and no components on the B-side. These features allow you to solder the board directly onto your own design, minimizing the height of your whole prototype. Oh, and did we mention the improved price? Thanks to a revised manufacturing process, the Arduino Nano Every costs a fraction of the original Nano … what are you waiting for? Upgrade now! Microcontroller ATMega4809 Operating Voltage 5 V Input Voltage 7 V - 21 V Analog Input Pins 8 Analog Output Pins Only through PWM External Interrupts all digital pins DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 48 KB SRAM 6 KB EEPROM 256 Byte Clock Speed 20 MHz LED_Builtin 13 UART 1 SPI 1 I2C 1 PWM Pins 5 USB Uses the ATSAMD11D14A Length 45 mm Width 18 mm Weight 5 g

    Out of stock

    € 19,95

    Members € 17,96

  • Arduino Pro Portenta H7

    Arduino Arduino Pro Portenta H7

    3 in stock

    Portenta H7 follows the Arduino MKR form factor, but enhanced with the Portenta family 80-pin high-density connector. Program it with high-level languages and AI while performing low-latency operations on its customizable hardware. Portenta H7 simultaneously runs high level code along with real time tasks. The design includes two processors that can run tasks in parallel. For example, is possible to execute Arduino compiled code along with MicroPython one, and have both cores to communicate with one another. The Portenta functionality is two-fold, it can either be running like any other embedded microcontroller board, or as the main processor of an embedded computer. Portenta can easily run processes created with TensorFlow Lite, you could have one of the cores computing a computer vision algorithm on the fly, while the other could be making low-level operations like controlling a motor, or acting as a user interface. Use Portenta when performance is key, among other cases, we envision it to be part of: High-end industrial machinery Laboratory equipment Computer vision PLCs Industry-ready user interfaces Robotics controller Mission-critical devices Dedicated stationary computer High-speed booting computation (ms) Two Parallel Cores H7's main processor is the dual core STM32H747 including a Cortex M7 running at 480 MHz and a Cortex-M4 running at 240 MHz. The two cores communicate via a Remote Procedure Call mechanism that allows calling functions on the other processor seamlessly. Both processors share all the in-chip peripherals and can run: Arduino sketches on top of the ARM Mbed OS Native Mbed applications MicroPython / JavaScript via an interpreter TensorFlow Lite Graphics Accelerator Probably one of the most exciting features of the Portenta H7 is the possibility of connecting an external monitor to build your own dedicated embedded computer with a user interface. This is possible thanks to the STM32H747 processor's on-chip GPU, the Chrom-ART Accelerator. Besides the GPU, the chip includes a dedicated JPEG encoder and decoder. A new standard for pinouts The Portenta family adds two 80-pin high density connectors at the bottom of the board. This ensures scalability for a wide range of applications by simply upgrading your Portenta board to the one suiting your needs. On-board Connectivity The onboard wireless module allows to simultaneously manage WiFi and Bluetooth connectivity. The WiFi interface can be operated as an Access Point, as a Station or as a dual mode simultaneous AP/STA and can handle up to 65 Mbps transfer rate. Bluetooth interface supports Bluetooth Classic and Bluetooth Low Energy. It is also possible to expose a series of different wired interfaces like UART, SPI, or I²C, both through some of the MKR styled connectors, or through the new Arduino industrial 80-pin connector pair. The 80-pin connector pair provides additional features including Ethernet. USB-C Multipurpose Connector The board's programming connector is a USB-C port that can also be used to power the board, as a USB Hub, to connect a DisplayPort monitor, or to deliver power to OTG connected devices. Specifications The Arduino Portenta H7 is based on the STM32H747 microcontroller, XI series. Microcontroller STM32H747XI dual Cortex-M7+M4 32bit low power ARM MCU (datasheet) Radio module Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth (Bluetooth Low Energy. 5 via Cordio stack, Bluetooth Low Energy 4.2 via Arduino Stack) (datasheet) Secure element (default) NXP SE0502 (datasheet) Board power supply (USB/VIN) 5 V Supported battery Li-Po Single Cell, 3.7 V, 700 mAh Minimum (integrated charger) Circuit operating voltage 3.3 V Display connector MIPI DSI host & MIPI D-PHY to interface with low-pin count large display GPU Chrom-ART graphical hardware Accelerator Timers 22x timers and watchdogs UART 4x ports (2 with flow control) Ethernet PHY 10 / 100 Mbps (through expansion port only) SD card Interface for SD Card connector (through expansion port only) Operational temperature -40 °C to +85 °C MKR headers Use any of the existing industrial MKR shields on it High-density connectors Two 80-pin connectors will expose all of the board's peripherals to other devices Camera interface 8-bit, up to 80 MHz ADC 3x ADCs with 16-bit max. resolution (up to 36 channels, up to 3.6 MSPS) DAC 2x 12-bit DAC (1 MHz) USB-C Host / Device, DisplayPort out, High / Full Speed, Power delivery Downloads Datasheet Schematics Pinout

    3 in stock

    € 129,95

    Members € 116,96

  • Arduino Uno Mini (Limited Editie)

    Arduino Arduino Uno Mini (Limited Edition)

    Celebrating the Arduino Uno with a miniaturized limited edition The world's favorite development board has gone mini. Everything in this version of the Arduino Uno is unique. Black and gold, finishing, elegant design and packaging, all delivered to the highest standard. A little jewel to celebrate the Arduino community and what we’ve been doing together for all these years. Each item is unique and numbered on the PCB, and includes a hand-signed letter from the founders. It’s a limited edition, so get while it’s in stock! For serious Arduino Uno lovers Arduino Uno Mini Limited Edition is a collector’s item for serious Arduino Lovers: hobbyists, students, makers, reimaginers, dreamers, hopers, fans, engineers, designers, questioners, cake-makers, problem-solvers, puzzlers, gamers, debaters, developers, entrepreneurs, architects, future-shapers, musicians, scientists... 10 million projects based on (official) Uno boards that have contributed to this incredible story. Specifications The Arduino Uno Mini Limited Edition is a microcontroller board based on the ATmega328P. It has 14 digital inputs/outputs (six of which can be used as PWM outputs), six analog inputs, a 16 MHz ceramic resonator, a USB-C connector, and a reset button. Contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable, use a power adapter, or connect a battery to get started. Microcontroller ATmega328P USB connector USB-C Built-in LED Pins 13 Digital I/O Pins 14 Analog Input Pins 6 PWM Pins 6 UART Yes I²C Yes SPI Yes Circuit operating voltage 5 V Input Voltage (limit) 6-12 V Battery connector None DC current per I/O Pin 20 mA DC current for 3.3 V Pin 50 mA Main processor ATmega328P (16 MHz) USB-serial processor ATmega16U2 (16 MHz) Memory ATmega328P 2 KB SRAM, 32 KB Flash, 1 KB EEPROM Weight 8.05 g Dimensions 26.70 x 34.20 mm Downloads Datasheet

    € 54,95

    Members € 49,46

  • Arduino Uno WiFi Rev2

    Arduino Arduino Uno WiFi Rev2

    Add this board to a device and you'll be able to connect it to a WiFi network, using its secure ECC608 crypto chip accelerator. The Arduino Uno WiFi is functionally the same as the Arduino Uno Rev3, but with the addition of WiFi / Bluetooth and some other enhancements. It incorporates the brand new ATmega4809 8-bit microcontroller from Microchip and has an onboard IMU (Inertial Measurement Unit) LSM6DS3TR. The Wi-Fi Module is a self-contained SoC with an integrated TCP/IP protocol stack that can provide access to a Wi-Fi network, or act as an access point. The Arduino Uno WiFi Rev.2 has 14 digital input/output pins – 5 that can be used as PWM outputs – 6 analog inputs, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable or power it with an AC adapter or battery to get started. Specifications Operating Voltage 5 V Input Voltage 7 V - 12 V Digital I/O 14 Analog Input Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 48 KB SRAM 6.144 Bytes EEPROM 256 Bytes Clock Speed 16 MHz Radio Module u-blox NINA-W102 Secure Element ATECC608A Inertial Measurement Unit LSM6DS3TR LED_Builtin 25 Length 101.52 mm Width 53.3 mm Weight 37 g

    € 59,95

    Members € 53,96

  • Arduino Ethernet Shield 2

    Arduino Arduino Ethernet Shield 2

    As always with Arduino, every element of the platform – hardware, software, and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, every day. The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the Shield. The Ethernet Shield 2 connects to an Arduino Board using long wire-wrap headers extending through the Shield. This keeps the pin layout intact and allows another Shield to be stacked on top of it. The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO Board. The Ethernet Shield 2 has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard micro-SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the Shield contained a full-size SD card slot; this is not supported. The Shield also includes a reset controller, to ensure that the W5500 Ethernet module is properly reset on power-up. Previous revisions of the Shield were not compatible with the Mega and needed to be manually reset after power-up.

    € 34,95

    Members € 31,46

  • Arduino Uno SMD Rev3

    Arduino Arduino Uno Rev3 SMD

    The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Additional features coming with the R3 version are: ATmega16U2 instead of 8U2 as a USB-to-Serial converter. 1.0 pinout: added SDA and SCL pins for TWI communication placed near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board and the second one is a not connected pin, that is reserved for future purposes. stronger RESET circuit. Microcontroller ATmega328P Operating Voltage 5 V Input Voltage 7 V - 12 V Digital I/O Pins 14 PWM Pins 6 Analog Input Pins 8 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz LED_Builtin 13 Length 68.6 mm Width 53.4 mm Weight 25 g

    € 22,95

    Members identical

  • Arduino Mega 2560 Rev3

    Arduino Arduino Mega 2560 Rev3

    It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila. Operating Voltage 5 V Input Voltage 7 V - 12 V Digital I/O 54 Analog Input Pins 16 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 256 KB of which 8 KB used by the bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16MHz LED_Builtin 13 Length 101.52 mm Width 53.3 mm Weight 37 g For more information, check out the Getting Started Guide from Arduino.

    € 44,95

    Members € 40,46

  • Arduino Leonardo met headers

    Arduino Arduino Leonardo with Headers

    1 review

    The Leonardo differs from all preceding boards in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Leonardo to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port. Microcontroller ATMega4809 Operating Voltage 5 V Input Voltage 7 V - 12 V Analog Input Pins 12 PWM Pins 7 DC I/O Pin 20 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB of which 4 KB used by the bootloader SRAM 2.5 KB EEPROM 1 KB Clock Speed 16 MHz Length 68.6 mm Width 53.3 mm Weight 20 g

    € 21,95

    Members € 19,76

  • Arduino Micro with Headers

    Arduino Arduino Micro with Headers

    The Micro contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard. The Micro board is similar to the Arduino Leonardo in that the ATmega32U4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port. Microcontroller ATmega32U4 Operating Voltage 5 V Input Voltage 7 V - 12 V Analog Input Pins 12 PWM Pins 7 DC I/O Pin 20 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB of which 4 KB used by the bootloader SRAM 2.5 KB EEPROM 1 KB Clock Speed 16 MHz LED_Builtin 13 Length 45 mm Width 18 mm Weight 13 g

    € 24,95

    Members € 22,46

  • Arduino Due met headers

    Arduino Arduino Due with Headers

    The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with an AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The Due follows the 1.0 pinout: TWI: SDA and SCL pins that are near to the AREF pin. IOREF: allows an attached shield with the proper configuration to adapt to the voltage provided by the board. This enables shield compatibility with a 3.3V board like the Due and AVR-based boards which operate at 5V. An unconnected pin, reserved for future use. Operating Voltage 3.3 V Input Voltage 7 V - 12 V Digital I/O 54 Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O Lines 130 mA DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 800 mA DC Current for 5 V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB Clock Speed 84 MHz Length 101.52 mm Width 53.3 mm Weight 36 g Please note: Unlike most Arduino boards, the Arduino Due board runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board.

    € 44,95

    Members € 40,46

  • Arduino Nano 33 IoT met Headers

    Arduino Arduino Nano 33 IoT with Headers

    The board's main processor is a low-power Arm® Cortex®-M0 32-bit SAMD21. The WiFi and Bluetooth® connectivity is performed with a module from u-blox, the NINA-W10, a low-power chipset operating in the 2.4GHz range. On top of that, secure communication is ensured through the Microchip® ECC608 crypto chip. Besides that, you can find a 6 axis IMU, which makes this board perfect for simple vibration alarm systems, pedometers, the relative positioning of robots, etc. WiFi and Arduino IoT Cloud You can get your board to connect to any kind of existing WiFi network, or use it to create your own Arduino Access Point. The specific set of examples we provide for the Nano 33 IoT can be consulted at the WiFiNINA library reference page. It is also possible to connect your board to different Cloud services, Arduino's own among others. Here are some examples of how to get the Arduino boards to connect to: Arduino's own IoT Cloud: Arduino's IoT Cloud is a simple and fast way to ensure secure communication for all of your connected Things. Check it out here. Blynk: a simple project from our community connecting to Blynk to operate your board from a phone with little code. IFTTT: see an in-depth case of building a smart plug connected to IFTTT. AWS IoT Core: we made this example on how to connect to Amazon Web Services. Azure: visit this GitHub repository explaining how to connect a temperature sensor to Azure's Cloud. Firebase: you want to connect to Google's Firebase, this Arduino library will show you how. Microcontroller SAMD21 Cortex®-M0+ 32bit low power ARM MCU Radio Module u-blox NINA-W102 Secure Element ATECC608A Operating Voltage 3.3 V Input Voltage 21 V Digital I/O Pins 14 PWM Pins 11 DC Current per I/O Pin 7 mA Analog Input Pins 8 Analog Output Pins 1 External Interrupts all digital pins UART 1 SPI 1 I2C 1 Flash Memory 256 KB SRAM 32 KB EEPROM none Clock Speed 48 MHz LED_Builtin 13 USB Native in the SAMD21 Processor IMU LSM6DS3 Length 45 mm Width 18 mm Weight 5 g

    € 32,95

    Members € 29,66

  • Arduino MKR FOX 1200

    Arduino Arduino MKR FOX 1200

    Out of stock

    The Arduino MKR FOX 1200 combines SigFox connectivity with the functionality of the Arduino MKR Zero. It is the ideal solution for beginners wanting to design IoT projects with a low power device. The Arduino MKR FOX 1200 is based on the Atmel SAMD21 and an ATA8520 SigFox module. The intelligent design enables the ability to power the board using an external 5 V power supply or two 1.5 V AA or AAA batteries. Features 32-bit computational power Rich set of I/O interfaces Low power SigFox communication Automatic switch between the two sources These features make this board an excellent choice for IoT battery-powered projects in a compact form factor. The USB port can supply power (5 V) to the board. The Arduino MKR FOX 1200 can run with or without the batteries connected and has limited power consumption. Please note: Unlike most Arduino boards, the Arduino MKR FOX 1200 runs at 3.3 V. The maximum voltage the I/O pins can handle is 3.3 V. Applying voltages higher than 3.3 V to any I/O pin could damage the board. While output to 5 V digital devices is possible, bidirectional communication with 5 V devices needs proper level shifting. Specifications Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Board Power Supply (USB/VIN) 5 V Circuit Operating Voltage 3.3 V PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 - or 19) Digital I/O Pins 8 UART 1 I²C 1 SPI 1 External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 - or 16-, A2 - or 17) Analog Input Pins 7 (ADC 8 / 10 / 12 bit) Analog Output Pins 1 (DAC 10 bit) DC Current per I/O Pin 7 mA SRAM 32 KB Flash Memory 256 KB EEPROM No Clock Speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 6 Full-Speed USB Device and embedded Host LED_BUILTIN 6 Antenna power 2 dB Carrier frequency 868 MHz Working region EU Dimensions 7.64 x 25 mm Weight 32 g Antenna The Arduino MKR FOX 1200 requires a GSM antenna to be attached to the board with the micro UFL connector; please make sure that the antenna is compatible with the frequencies in the SigFox's range (868 Mhz). Please note: Do not attach the antenna to a metallic surface Batteries, Pins and board LEDs Battery capacity: The batteries must have a voltage of 1.5 V. Battery connector: To connect a battery pack (2x AA or AAA) to the Arduino MKR FOX 1200, use the screw terminal block. Polarity: On the silk in the bottom of the board, a positive pin is the closest to the USB connector VIN: This pin can power the board with a regulated 5 V source. If the power goes through this pin, the USB power source is disconnected. That is the only way to supply 5 V to the board, without using USB. 5 V: This pin outputs 5 V from the board when powered from the USB connector or the VIN pin. VCC: This pin outputs 3.3 V through the on-board voltage regulator. This voltage is 3.3 V if USB or VIN is used or equal the two batteries if they are used LED ON: The LED is connected to the 5 V input from either USB or VIN. It is not connected to the batteries. That results in the LED lighting up when the power comes from USB or VIN and staying off when the board is running on battery. That minimizes the waste of energy stored in the battery. Onboard LED: On Arduino MKR FOX 1200, the built-in LED is connected to D6 and not D13 as on the other boards. Blink example or other sketches that uses pin 13 for onboard LED may need to be changed to work properly.

    Out of stock

    € 49,95

    Members € 44,96

  • Arduino Nano 33 BLE Sense Rev2 met headers

    Arduino Arduino Nano 33 BLE Sense Rev2 with Headers

    The Arduino Nano 33 BLE Sense Rev2 with headers is Arduino’s 3.3 V AI enabled board in the smallest available form factor with a set of sensors that will allow you without any external hardware to start programming your next project, right away. With the Arduino Nano 33 BLE Sense Rev2, you can: Build wearable devices that using AI can recognize movements. Build a room temperature monitoring device that can suggest or modify changes in the thermostat. Build a gesture or voice recognition device using the microphone or the gesture sensor together with the AI capabilities of the board. Differences between Rev1 and Rev2 Replacement of IMU from LSM9DS1 (9 axis) for a combination of two IMUs (BMI270 – 6 axis IMU and BMM150 – 3 axis IMU) Replacement of temperature and humidity sensor from HTS221 for HS3003 Replacement of microphone from MP34DT05 to MP34DT06JTR Replacement of power supply MPM3610 for MP2322 Addition of VUSB soldering jumper on the top side of the board New test point for USB, SWDIO and SWCLK Specifications Microcontroller nRF52840 (datasheet) Operating Voltage 3.3 V Input Voltage (limit) 21 V DC Current per I/O Pin 15 mA Clock Speed 64 MHz CPU Flash Memory 1 MB (nRF52840) SRAM 256 KB (nRF52840) EEPROM None Digital Input / Output Pins 14 PWM Pins All digital pins UART 1 SPI 1 I²C 1 Analog Input Pins 8 (ADC 12 bit 200 k samples) Analog Output Pins Only through PWM (no DAC) External Interrupts All digital pins LED_BUILTIN 13 USB Native in the nRF52840 Processor IMU BMI270 (datasheet) and BMM150 (datasheet) Microphone MP34DT06JTR (datasheet) Gesture, light, proximity, color APDS9960 (datasheet) Barometric pressure LPS22HB (datasheet) Temperature, humidity HS3003 (datasheet) Downloads Datasheet Schematics

    € 54,95

    Members € 49,46

  • Arduino Pro Portenta Max Carrier

    Arduino Arduino Pro Portenta Max Carrier

    Max Carrier transforms Portenta modules into single-board computers or reference designs that enable edge AI for high-performance industrial, building automation and robotics applications. Thanks to dedicated high-density connectors, it can be paired with Portenta X8 or H7, allowing you to easily prototype and deploy your industrial projects. This Arduino Pro carrier further augments Portenta connectivity options with Fieldbus, LoRa, Cat-M1 and NB-IoT. Among the many available plug-and-play connectors there are Ethernet, USB-A, audio jacks, microSD, mini-PCIe, FD-CAN and Serial RS232/422/485. Max Carrier can be powered via external supply (6-36 V) or battery via the onboard 18650 Li-ion battery connector with 3.7 V battery charger. Features Easily prototype industrial applications and minimize time to market A powerful carrier exposing Portenta peripherals (e.g. CAN, RS232/422/485, USB, mPCIe) Multiple connectivity options (Ethernet, LoRa, CAT-M1, NB-IoT) MicroSD for data logging operations Integrated audio jacks (line-in, line-out, mic-in) Standalone when battery powered Onboard JTAG debugger via micro-USB (with Portenta H7 only) Specifications Connectors High-Density connectors compatible with Portenta products2x USB-A female connectors1x Gigabit Ethernet connector (RJ45)1x FD-Can on RJ111x mPCIe1x Serial RS232/422/485 on RJ12 Audio 3x audio jacks: stereo line-in/line-out, mic-inSpeaker connector Memory Micro SD Wireless modules Murata CMWX1ZZABZ-078 LoRaSARA-R412M-02B (Cat.M1/NB-IoT) Operating temperatures -40 °C to +85 °C (-40° F to 185 °F) Debugging Onboard JLink OB / Blackmagic probe Power/battery Power Jack for external supply (6-36 V)On-board 18650 Li-ion battery connector with battery charger (3.7 V) Dimensions 101.6 x 101.6 mm (4.0 x 4.0') Downloads Datasheet Schematics

    € 439,00

    Members € 395,10

  • Last stock! De Arduino Pro Portenta X8

    Arduino Arduino Pro Portenta X8

    1 in stock

    Portenta X8 is a powerful, industrial-grade SOM with Linux OS preloaded onboard, capable of running device-independent software thanks to its modular container architecture. Take advantage of onboard Wi-Fi/Bluetooth Low Energy connectivity to securely perform OS/application OTA updates. It’s basically two industrial products in one, with the power of no less than 9 cores. Leverage the Arduino environment to carry out real-time tasks while Linux takes care of high-performance processing. Portenta X8 features an NXP i.MX 8M Mini Cortex-A53 quad-core, up to 1.8 GHz per core + 1x Cortex-M4 up to 400 MHz, plus the STMicroelectronics STM32H747 dual-core Cortex-M7 up to 480 Mhz +M4 32-bit ARM MCU up to 240 Mhz. Features Two industrial products in one, combining Arduino’s availability of libraries/skills with container-based Linux distribution Outstanding computational density – a total of 9 cores within a compact form factor Multi-processor architecture allowing power-optimized processing Leverage popular programming languages like Python, Java and Ruby among others Real-time I/O and fieldbus/control on a dedicated core Deploy powerful AI algorithms and machine learning on the edge Secure OS/applications updates over-the-air Industrial-grade security at the hardware level, thanks to its crypto chip on dedicated bus Leverage the Arduino ecosystem to expand Portenta capabilities Implement multi-protocol routing with a single module Compatible with other Arduino Portenta products Industrial-Grade Security Portenta X8 has been designed with industrial-grade security in mind. PSA Certified and includes the NXP SE050C2 hardware security element to provide key generation, accelerated crypto operations and secure storage. Awarded Arm SystemReady certification and integrated Parsec services, making it one of the market’s first Cassini Products available to developers. Portenta X8 includes the customizable open-source Linux microPlatform OS, built using best industry practices for end-to-end security, incremental OTA updates and fleet management. Utilizing the cloud-based DevOps platform from Foundries.io to reinvent the way embedded Linux solutions are built, tested, deployed and maintained, the Portenta X8 benefits from Foundries.io continuous update service for cybersecurity. This service guarantees an updated image that contains all vulnerability patches; whilst the approach to containers decouples the operating system from the application, to seamlessly keep the whole system updated. Applications Portenta X8 enables IT professionals, system integrators and consulting firms to build and boost a wide variety of solutions for industrial contexts, and also lends itself to building automation and smart agriculture applications. Connected edge computer for manufacturing Autonomous Guided Vehicles (AGV) Interactive full-HD secure kiosks and digital signage Office & home control systems Navigation and control for smart agriculture Behavioral analytics for offices and factories Downloads Datasheet Schematics

    1 in stock

    € 239,00

    Members € 215,10

  • Arduino MKR WiFi 1010

    Arduino Arduino MKR WiFi 1010

    The board's main processor is a low-power ARM Cortex-M0 32-bit SAMD21, like in the other boards within the Arduino MKR family. The WiFi and Bluetooth connectivity is performed with a module from u-blox, the NINA-W10, a low-power chipset operating in the 2.4 GHz range. On top of that, secure communication is ensured through the Microchip ECC508 crypto chip. Besides that, you can find a battery charger, and an RGB LED on-board. Official Arduino WiFi Library You can get your board to connect to any kind of existing WiFi network, or use it to create your own Arduino Access Point. The specific set of examples we provide for the MKR WiFi 1010 can be consulted at the WiFiNINA library reference page. Compatible with other Cloud Services It is also possible to connect your board to different Cloud services, Arduino's own among others. Here are some examples of how to get the MKR WiFi 1010 to connect to: Blynk: a simple project from the Arduino community connecting to Blynk to operate your board from a phone with little code IFTTT: in-depth case of building a smart plug connected to IFTTT AWS IoT Core: Arduino made this example on how to connect to Amazon Web Services Azure: visit this GitHub repository explaining how to connect a temperature sensor to Azure's Cloud Firebase: you want to connect to Google's Firebase, this Arduino library will show you how Specifications Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Radio Module u-blox NINA-W102 Power Supply 5 V Secure Element ATECC508 Supported Battery Li-Po Single Cell, 3.7 V, 1024 mAh Minimum Operating Voltage 3.3 V Digital I/O Pins 8 PWM Pins 13 UART 1 SPI 1 I2C 1 Analog Input Pins 7 Analog Output Pins 1 External Interrupts 10 Flash Memory 256 KB SRAM 32 KB EEPROM no Clock Speed 32.768 kHz, 48 MHz LED_Builtin 6 USB Full-Speed USB Device and embedded Host Length 61.5 mm Width 25 mm Weight 32 g

    € 39,95

    Members € 35,96

  • Arduino Pro Portenta H7 Lite

    Arduino Arduino Pro Portenta H7 Lite

    Portenta H7 Lite allows you to build your next smart project. Ever wanted an automated house? Or a smart garden? Well, now it’s easy with the Arduino IoT Cloud compatible boards. It means: you can connect devices, visualize data, control and share your projects from anywhere in the world. The Portenta H7 Lite is very similar to the Portenta H7, that simultaneously can run high level code along with real time tasks thanks to its two processors. It is, for example, possible to execute Arduino compiled code along with MicroPython one and have both cores to communicate with one another. However, the H7 Lite is a low-cost board with H7 functionalities that can be configured to specific use cases. Features Dual Core – Two best-in-class processors in one, running parallel tasks AI on the edge – So powerful it can run AI state machines Customization – The board is highly customizable in volumes High-level programming language support (Micropython) The Portenta H7 Lite offers twofold functionality: it can run either like any other embedded microcontroller board, or as the main processor of an embedded computer. For example, use the Portenta Vision Shield to transform your H7 Lite into an industrial camera capable of performing real-time machine learning algorithms on live video feeds. As the H7 Lite can easily run processes created with TensorFlow Lite, you could have one of the cores computing a computer vision algorithm on the fly, while the other carries out low-level operations like controlling a motor or acting as a user interface. Solutions High-end industrial machinery Laboratory equipment Computer vision PLCs Robotics controllers Mission-critical devices High-speed booting computation (ms) Two Parallel Cores The Portenta H7 Lite’s main processor is the STM32H747 dual core including a Cortex-M7 running at 480 MHz and a Cortex-M4 running at 240 MHz. The two cores communicate via a Remote Procedure Call mechanism that allows calling functions on the other processor seamlessly. Both processors share all the in-chip peripherals and can run: Arduino sketches on top of the ARM Mbed OS Native Mbed applications MicroPython / JavaScript via an interpreter TensorFlow Lite A New Standard for Pinouts The Portenta family adds two 80-pin high-density connectors at the bottom of the board. This ensures scalability for a wide range of applications: simply upgrade your Portenta board to the one suiting your needs. USB-C Multipurpose Connector The board’s programming connector is a USB-C port that can also be used to power the board, as a USB Hub, or to deliver power to OTG connected devices. Arduino IoT Cloud Use your Portenta board on Arduino’s IoT Cloud, a simple and fast way to ensure secure communication for all of your connected Things. Specifications Microcontroller STM32H747XI Dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet) Secure element (default) Microchip ATECC608 Board power supply (USB/VIN) 5 V Supported battery Li-Po Single Cell, 3.7 V, 700 mAh Minimum (integrated charger) Circuit operating voltage 3.3 V Current consumption 2.95 μA in Standby mode (Backup SRAM OFF, RTC/LSE ON) Timers 22x timers and watchdogs UART 4x ports (2 with flow control) Ethernet PHY 10 / 100 Mbps (through expansion port only) SD card Interface for SD card connector (through expansion port only) Operational temperature -40 °C to +85 °C MKR headers Use any of the existing industrial MKR shields on it High-density connectors Two 80-pin connectors will expose all of the board's peripherals to other devices Camera interface 8-bit, up to 80 MHz ADC 3x ADCs with 16-bit max. resolution (up to 36 channels, up to 3.6 MSPS) DAC 2x 12-bit DAC (1 MHz) USB-C Host / Device, High / Full Speed, Power delivery Downloads Datasheet Schematics

    € 94,95

    Members € 85,46

  • Arduino MKR Zero

    Arduino Arduino MKR Zero

    The Arduino MKR Zero is a development board for music makers! With an SD card holder and dedicated SPI interfaces (SPI1), you are able to play music files without extra hardware. The MKR Zero brings you the power of a Zero in the smaller format established by the MKR form factor. The MKR Zero board acts as a great educational tool for learning about 32-bit application development. It has an on-board SD connector with dedicated SPI interfaces (SPI1) that allows you to play with MUSIC files with no extra hardware! The board is powered by Atmel’s SAMD21 MCU, which features a 32-bit ARM Cortex M0+ core. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it by a LiPo battery. The battery voltage can also be monitored since a connection between the battery and the analog converter of the board exists. Specifications Microcontroller SAMD21 ARM Cortex-M0+ 32-bit low power Board power supply (USB/VIN) 5 V Supported battery Li-Po single cell, 3.7 V, 700 mAh minimum DC current for 3.3 V pin 600 mA DC current for 5 V pin 600 mA Circuit operating voltage 3.3 V Digital I/O pins 22 PWM pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19) UART 1 SPI 1 I²C 1 Analog input pins 7 (ADC 8/10/12 bit) Analog output pins 1 (DAC 10 bit) External interrupts 10 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17) DC current per I/O pin 7 mA Flash memory 256 KB Flash memory for bootloader 8 KB SRAM 32 KB EEPROM No Clock speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 32 Downloads Datasheet Eagle Files Schematics Fritzing Pinout

    € 36,95

    Members € 33,26

Login

Forgot password?

Don't have an account yet?
Create an account