Siglent's SDS2000X Plus series Digital Storage Oscilloscopes are available in bandwidths of 100 MHz, 200 MHz, and 350 MHz, have a maximum sample rate of 2 GSa/s, a maximum record length of 200 Mpts/ch, and up to 4 analog channels + 16 digital channels mixed-signal analysis ability.
The SDS2000X Plus series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications that require more than 8-bit resolution.
The large 10.1’’ capacitive touch screen supports multi-touch gestures, while the remote web control, mouse and external keyboard support greatly improve the operating efficiency of the SDS2000X Plus.
Features
100 MHz, 200 MHz, 350 MHz (upgradable to 500 MHz) models
Real-time sampling rate up to 2 GSa/s
Record length up to 200 Mpts
Serial bus triggering and decoder, supports I²C, SPI, UART, CAN, LIN, CAN FD, FlexRay, I²S and MIL-STD-1553B
Provide 10 bit mode, Vertical and Horizontal Zoom
Capacitive touch screen supports multi-touch gestures
Siglent SDS2000X Plus Oscilloscopes
SDS2102X Plus
SDS2104X Plus
SDS2204X Plus
SDS2354X Plus
Bandwidth
100 MHz
100 MHz
200 MHz
350 MHz
Channels
2
4
4
4
Real-time sampling rate
2 GSa/s
2 GSa/s
2 GSa/s
2 GSa/s
Capture rate
120,000 wfm/s
120,000 wfm/s
120,000 wfm/s
120,000 wfm/s
Memory depth
200 Mpts/ch
200 Mpts/ch
200 Mpts/ch
200 Mpts/ch
Included
Siglent SDS2204X Plus Oscilloscope
Passive probes
Power cord
USB cable
Manual
Downloads
Datasheet
Manual
Quick guide
Manual
Firmware
Features
Synchronous mode: Auto, Normal, Single, None, Scan
Rising/Falling edge trigger
Modes of vertical precise, horizontal precise measurement and triggering threshold
Auto Measurement: frequency, cycle time, duty cycle, DC RMS voltage/Vpp /Vmax/Vmin/Vavg
Inbuilt signal generator/10 Hz-1 MHz square wave (duty adjustable) or 10 Hz-20 KHz
Sine/Square/Triangle/Sawtooth wave
Specifications
Analog bandwidth
1 MHz
Max sample rate
10 Msa/s
Max sample memory depth
8K
Analog input impedance
1 MΩ
Max input voltage
±40 V (X1)
Coupling
AC/DC
Vertical sensitivity
20 mv/Div~10 V/Div (1-2-5)
Horizontal sensitivity
1 uS/Div~2 S/Div (1-2-5)
Storage
Built-in 8 MB U disk storage for waveform data and images
Power supply
Internal 550 mAh Lithium battery, recharging through Micro USB port
Display
2.8' Full Color TFT LCD (320x240 pixels)
Dimensions
100 x 56.5 x 10.7 mm
Downloads
User Manual
Source Code
App
The PeakTech 1265 is an affordable 30 MHz 2-channel digital storage oscilloscope with a high-resolution TFT color display and extensive additional functions. It has a sampling rate of up to 250 MS/s and convinces with its high quality and easy handling with the best price/performance ratio. To quickly display each incoming waveform, simply press the Autoset key and the oscilloscope itself searches for the best possible display. With Autoscale, however, the scaling of the time base can be adjusted in a user-friendly manner. This oscilloscope has a VGA output for displaying the oscilloscope display on an external monitor or projector.
Features
2-channel oscilloscope with 30 MHz analog bandwidth at max. 250 MS/s sampling rate
8 inch (20 cm) TFT color display with 800 x 600 pixels
LAN, USB host, USB device & VGA interface
Autoset function for user-friendly operation
Recording length of max. 10,000 points
Automatic measurement modes, XY mode and FFT function
Specifications
Bandwidth
30 MHz
Channels
2
Screen size (TFT)
8' (20 cm)
Resolution
800 x 600 Pixel
Display Type
Color-TFT
Sampling 1 CH
250 MS/s
Sampling 2 CH
125 MS/s
Hor. scale max.
100 s/div
Hor. scale min.
5 ns/div
Memory depth
10,000 Points
Rise Time
< 14 ns
Vert. resolution
8 Bit
Vert. scale max.
10 V/div
Vert. scale min.
2 mV/div
Interfaces
1x USB, 1x LAN, 1x VGA
Mains voltage
110/240 V AC; 50/60 Hz
Included
PeakTech 1265 Oscilloscope
USB cable
Software CD for Windows
Power cord
2 probes
BNC cable
Carrying case
Manual
Downloads
Software
Datasheet_DE-EN
Datasheet_FR
Datasheet_IT
Datasheet_ES
Siglent's SDS2000X Plus series Digital Storage Oscilloscopes are available in bandwidths of 100 MHz, 200 MHz, and 350 MHz, have a maximum sample rate of 2 GSa/s, a maximum record length of 200 Mpts/ch, and up to 4 analog channels + 16 digital channels mixed-signal analysis ability.
The SDS2000X Plus series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications that require more than 8-bit resolution.
The large 10.1" capacitive touch screen supports multi-touch gestures, while the remote web control, mouse and external keyboard support greatly improve the operating efficiency of the SDS2000X Plus.
Features
100 MHz, 200 MHz, 350 MHz (upgradable to 500 MHz) models
Real-time sampling rate up to 2 GSa/s
Record length up to 200 Mpts
Serial bus triggering and decoder, supports I²C, SPI, UART, CAN, LIN, CAN FD, FlexRay, I²S and MIL-STD-1553B
Provide 10 bit mode, Vertical and Horizontal Zoom
Capacitive touch screen supports multi-touch gestures
Siglent SDS2000X Plus Oscilloscopes
SDS2102X Plus
SDS2104X Plus
SDS2204X Plus
SDS2354X Plus
Bandwidth
100 MHz
100 MHz
200 MHz
350 MHz
Channels
2
4
4
4
Real-time sampling rate
2 GSa/s
2 GSa/s
2 GSa/s
2 GSa/s
Capture rate
120,000 wfm/s
120,000 wfm/s
120,000 wfm/s
120,000 wfm/s
Memory depth
200 Mpts/ch
200 Mpts/ch
200 Mpts/ch
200 Mpts/ch
Included
Siglent SDS2354X Plus Oscilloscope
Passive probes
Power cord
USB cable
Manual
Downloads
Datasheet
Manual
Quick guide
Manual
Firmware
The OWON VDS6000 Series PC Oscilloscope combines powerful performance with a sleek, ultra-thin design. With 100 MHz bandwidth, 1 GSa/s real-time sampling, and up to 14-bit resolution, it delivers highly accurate measurements. The built-in 5 MHz function generator, USB-C power supply, and optional WiFi connectivity make it incredibly versatile.
Compatible with Windows, Linux, Android, and iOS, the VDS6000 is perfect for labs, fieldwork, and remote diagnostics – compact, flexible, and ready for any challenge.
Features
Bandwidth: 100 MHz
Vertical resolution: 14 bits
Rise time: ≤3.5 ns
Memory: 10 Mpts
Number of channels: 2 channels + 1 channel function generator
Horizontal scale: 5ns - 100s/div
Sample rate: Max. 1 GSa/s
Maximum voltage: 40 V (peak - peak)
Automatic measurements: Vpp, Vavg, Vamp, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Overshoot, Preshoot, Rise Time,
Connectivity: USB-C, LAN, Wifi (optional)
Fall Time, Delay A→B↑, Delay A→B↓, +Width, -Width, +Duty, -Duty
Bandwidth: 5 MHz
Sample rate: 25 MSa/s
Standard waveforms: Sine (0.1 Hz - 5 MHz), Square (0.1 Hz - 200 kHz), Ramp (1 Hz - 10 kHz), Pulse (1 Hz - 10 kHz)
Resolution: 10 bits
DC offset range (AC + DC): ±2.5 V
Amplitude range: 10 mVpp - 5 Vpp
Dimensions: 190 x 120 x 18 mm
Weight: 380 g
Downloads
Manual
Quick Guide
PC Software
MacOS Software
The FNIRSI 1013D is a fully featured 2-channel tablet oscilloscope with a high-resolution 7-inch LCD screen (800 x 480 pixels). The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz.
With full trigger functions (single/normal/automatic), it can be used for periodic analog signals or non-periodic digital signals. The built-in high-voltage protection module can withstand a continuous voltage of up to 400 V.
Features
Intelligent anti-burn,1X can withstand up to 400 V withstand voltage.
100 MHz analog bandwidth @ 1 GSa/s sampling rate (1X = 5 MHz,10X = 100 MHz).
Fully fit 7-inch 800 x 480 resolution color TFT LCD display with bright colors and high contrast.
Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation.
High measurement voltage range, 1X can measure 0~40 V, 10X can measure 0~400 V,100X can measure 0~4000 V.
Up to 12 parameters measurement: VPP, VP, Vmax, Vmin, Vavg, Vrms, Frequent, Duty+, Duty-, Time+, Time−, Period.
Cursor measurement function, it is convenient to manually measure the period and frequency and voltage.
Complete triggering function (single, normal, automatic).
At any time, the waveform display (pause function) is frozen.
Equipped with high efficiency One-button AUTO.
One-button waveform storage and screenshot.
Built-in 1 GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data.
Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc.
Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis.
Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals.
FFT display function, can analyze the spectral characteristics of the signal.
Built-in 6000 mAh rechargeable lithium battery, fully charged for 4 hours of continuous use at the highest screen brightness.
Memory compression technology, waveform refresh screen does not flicker.
Screen brightness adjustment.
Background grid brightness adjustment.
Applications
Electronic DIY
Appliance repair
Car repair
Equipment debug
Scientific research
Product development
Specifications
Channels
2
LCD size
7 inch
LCD resolution
800 x 480
Display technology
TFT
Bandwidth
100 Mhz
Sampling rate
1 GSa/s
Rise time
<3nS
Storage depth
240 Kbit
Input resistance
1 MΩ
Sensitivity
50 mV ~ 500 V
Time base
50S ~ 10nS
Trigger mode
Single/Normal/Auto
Trigger edge
Rising/Falling
Coupling
AC/DC
Highest test voltage
1X: 40 V, 10X: 400 V
Cursor
Position XY, Trigger Y
Roll mode
Yes
One button AUTO
Yes
Waveform storage
1000 pictures + 1000 waveforms
Waveform manager
Yes
Voltage accuracy
±2%
Frequency precision
±0.01% high precision
Parameter
12 kinds in total
Battery
6000 mAh Lithium
Standby
4 hours
Extension
USB export
Power supply
USB-C, 5 V @ 2 A/3 A/4 A
Dimensions
184 x 124 x 50 mm
Weight
650 g
Included
1x FNIRSI 1013D 2-ch Tablet Oscilloscope
2x 100 MHz Probes (1X and 10X)
1x USB charger
1x USB cable
1x Manual
Downloads
Manual
Firmware
The FNIRSI DSO152 is an extremely practical and cost-effective handheld oscilloscope with a real-time sampling rate of 2.5 MSa/s, a bandwidth of 200 kHz and complete trigger functions (single, normal and automatic).
It can be used for both periodic analog signals and non-periodic digital signals and can measure voltages up to ±400 V. Equipped with an efficient one-key AUTO, it can display the measured waveform without cumbersome adjustments. It is equipped with a high-resolution 2.8-inch LCD screen with a resolution of 320x240 pixels and a built-in 1000 mAh high-quality lithium battery for up to 4 hours of operation.
Specifications
Sampling rate
2.5 MSa/s
Bandwidth
200 kHz
Vertical sensitivity
10 mV/DIV - 20 V/DIV (Progress according to the 1-2-5 way)
Time base range
10µS/DIV - 50s/DIV (Progress according to the 1-2-5 way)
Voltage range
X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V)
Trigger method
Auto/Normal/Single
Coupling method
AC/DC
Display
2.8" (320 x 240 pixels)
USB charging
5 V/1 A
Lithium battery capacity
1000 mAh
Square wave calibration
Frequency: 1K, Duty cycle: 50%
Dimensions
99 x 68.3 x 19.5 mm
Weight
100 g
Included
FNIRSI DSO152 oscilloscope
Alligator clip probe
USB cable
Lanyard
Manual
Downloads
Manual
Firmware V0.1
An illustrated chronicle of Teknology for collectors and restorers
Oscilloscopes have made a major contribution to the advancement of human knowledge, not only in electronics, but in all sciences, whenever a physical quantity can be converted into a timerelated electrical signal.
This book traces the history of a crucial instrument through many Tektronix products. This is the company that invented and patented most of the functions found in all oscilloscopes today. Tek is and will always be synonymous with the oscilloscope.
In nearly 600 pages, with hundreds of gorgeous photos, diagrams, anecdotes, and technical data, you'll travel through the history of Tektronix in a superb collector's edition with a technical point of view. The author is not afraid to get his hands dirty restoring his own Tek equipment. The journey starts in the early 1950s. It ends in the '90s, after exploring the ins and outs of the most interesting models in the 300, 400, 500, 5000, 7000, and 11000 series, from tubes to advanced hybrid technologies.
Downloads
NEW: Free Supplement (136 pages, 401 MB)
The JOY-iT JDS2960 is a 2-channel signal generator capable of producing signals up to 60 MHz. Its compact design and the option to operate it with a power bank make it ideal for mobile use.
With a variety of waveforms, including sine, square, triangle, pulse, half-wave, and more, it is suitable for various measurement technology applications.
Additionally, the JDS2960 features a 1-channel frequency allocation. Its high frequency accuracy of ±20 ppm and stability of ±1 ppm/3 h ensure excellent signal quality and great flexibility.
The 2.4-inch TFT color display provides user-friendly operation and enables a wide range of applications.
Features
2 Channels
Up to 60 MHz
Robust aluminum housing
1-channel frequency counter
Up to 20 Vpp
Many different pre-programmed waveforms and up to 60 user-defined waveforms
Pulse function
Specifications
Channels
2-channel Signal Generator1-channel Frequency meter
Frequency range
Sine: 0-60 MHzSquare, triangle: 0-25 MHzTTL, Pulse: 0-6 MHz
Signal forms
Sine, square, triangle, pulse, half/solid wave, exponential rise/fall, etc.
Measuring range frequency counter
1-100 MHz
Frequency accuracy
±20 ppm
Frequency stability
±1 ppm/3 h
Sampling rate
266 MSa/s
Display
2,4" TFT color LCD
Vertical shaft resolution
14 bits
Amplitude range
<10 MHz: 0-20 Vpp>10 MHz: 0-10 Vpp
Amplitude resolution
1 mV
Amplitude stability
±5%/5h
Amplitude flatness
<10 MHz: ±5%>10 MHz: ±10%
Impedance of output
50 Ω ±10%
Distortion factor
<0.8% (20 Hz-20 KHz, 0 dBm)
Dimensions
145 x 95 x 55 mm
Weight
900 g
Included
1x JOY-iT JDS2960 2-ch Signal Generator
1x Power supply unit
1x BNC-BNC cable
2x BNC crocodile clip cables
1x USB-DC power cable
1x USB data cable
Downloads
Datasheet
Manual
Software
,
by Clemens Valens
Owon HDS2102S Handheld 2-Channel 100 MHz Oscilloscope, Multimeter & Signal Generator (Review)
The Owon HDS2102S is a versatile handheld device that combines a two-channel 100 MHz oscilloscope, a multimeter, and an arbitrary waveform generator all in one...
,
by Clemens Valens
FNIRSI DPOX180H 2-in-1 Digital Phosphor Oscilloscope (Review)
Oscilloscopes sure have made a lot of progress over the past two decades. Twenty years ago, I still used my single-beam analog 20 MHz CRT oscilloscope...