Platforms

126 products


  • RTL-SDR (Software Defined Radio) met Dipool Antenne Kit

    RTL-SDR RTL-SDR V3 (Software Defined Radio) with Dipole Antenna Kit

    2 reviews

    RTL-SDR is an affordable dongle that can be used as a computer based radio scanner for receiving live radio signals in your area. This particular dongle includes a R820T2 tuner, a 1 PPM temperature compensated oscillator (TCXO), SMA F connector. It features an aluminium case with passive cooling via a thermal pad. Moreover, there is a software switchable bias tee circuit, supplementary ESD protection, lower overall noise and built-in direct sampling for HF reception. This device can receive frequencies from 500 kHz to 1.7 GHz and has up to 3.2 MHz of instantaneous bandwidth (2.4 MHz stable). Note: RTL-SDR dongles are RX only. You can use this kit either for terrestrial or satellite reception just by changing the orientation of the antenna. Thanks to the included mounts and extension cables it is possible to temporarily place the antenna outside for a better reception. Other potential applications are general radio scanning, air traffic control, public safety radio, ADSB, ACARS, trunked radio, P25 digital voice, POCSAG, weather balloons, APRS, NOAA APT weather satellites, radio astronomy, meteor scatter monitoring etc. Included RTL-SDR V3 Dongle (R820T2 RTL2832U 1PPM TCXO SMA) 2x 23 cm to 1 m telescopic antenna 2x 5 cm to 13 cm telescopic antenna Dipole Antenna Base with 60 cm RG174 extension cable 3 m RG174 extension cable Flexible Tripod Mount Suction Cup Mount Downloads Quick Start Guide SDR# User Guide Dipole Antenna Kit Guide

    $67.00

    Members $60.30

  •  -17% Digitaal Desoldeerstation ZD-915

    Zhongdi Digital Desoldering Station ZD-915

    1 review

    Out of stock

    The ZD-915 is a digital desoldering station with ESD protection and digital display of both the actual and set value on an LCD screen. This desoldering station has high power in a compact and robust housing and makes desoldering easy, because it can be operated with one hand. The ZD-915 features a soldering gun that houses a filter that catches any sucked material, so you only need to replace the filters to continue. There is also a temperature sensor in the tip so that temperature fluctuations can be quickly absorbed. Features The temperature is easily adjusted by simple up/down buttons. 140 W temperature controlled soldering station with adjustable range from 160 °C to 480 °C. The desoldering station is designed for lead free desoldering specially. The side of the station features a typical holder with sponge. An illuminated power on/off is also loacted on the front. Specifications Station Voltage supply 220-240 V Power consumption 140 W Vakuum pressure 600 mm HG Desoldering Gun Power consumption 24 V AC 80 WHeat up rating 130 W Temperature 160-480 °C Heating element Ceramic heater Included 1x Desoldering station ZD-915 2x Spare soldering tip 3x Cleaning needle for desoldering tips 1x Spare filter for desoldering gun 1x Manual

    Out of stock

    $134.00$111.00

    Members identical

  •  -33% MightyOhm Geigerteller kit (incl. behuizing)

    MightyOhm MightyOhm Geiger Counter Kit (incl. Case)

    Have you ever wondered if the objects in your house are radioactive or not? Does the apple in your fridge give off radiation? Are the books on your shelves giving off gamma rays? You can easily find that out by building your Geiger counter! Thanks to the serial logging function you can track exposure over time, and you can use the mute button to detect radiation without any noise. Detect beta and gamma radiation with your own portable Geiger counter! Features 100% Open Source Hardware! Sensitive to beta and gamma radiation LED and piezo speaker alert you to detected radioactivity. Mute button for silent operation. An ATtiny2313 microcontroller brain that is begging to be hacked! Support for several common Geiger-Müller tubes: SI-3BG, SI-1G, and SBM-20. HV supply can be adjusted from ~300-600 V. Headers for serial (9600 baud), in-circuit programming of the AVR microcontroller, and pulse output (to connect the Geiger counter to other stuff!) Serial data logging! Counts per second (CPS), counts per minute (CPM), and equivalent dose are reported via the serial port once a second. Included Geiger counter kit incl. PCB and all parts 1x SBM-20 Geiger-Müller tube 1x Laser cut acrylic case Downloads Assembly Instructions Case Assembly Instructions Design Files Source Code Usage Instructions

    $150.00$100.00

    Members identical

  •  -18% 2-in-1 SMD Hetelucht Rework Station ZD-8922

    Zhongdi 2-in-1 SMD Hot Air Rework Station ZD-8922

    This 2-in-1 SMD hot air soldering station offers a cost-effective solution for soldering and desoldering all types of SMD components. Features Incl. soldering iron and hot air pump. It is suitable for soldering and desoldering all types of surface mounted IC, PCB or components. The control unit has 2 LEDs that display the temperature and in °C and °F. The temperature can be easily adjusted with simple up/down buttoms. The hot air temperature can be calibrated from 3L/min to 24L/min continuously. Temperature is micro-processor controlled and can be adjusted. Temperature range: 50-480 °C for soldering iron, 100-500 °C for hot air pump. Specifications Power Soldering iron: 24 V, 60 WHot air pump: 300 W Power supply 220-240 VAC 50 Hz Temperature range Soldering iron: 50-480 °CHot air pump: 100-500 °C Dimensions 113 x 125 x 175 mm Weight 2 kg Included 1x Soldering station 1x Soldering iron 1x Hot air gun 3x Hot air nozzle 1x Soldering iron with needle bit 1x Power cord 1x Soldering iron stand with sponge

    $122.00$100.00

    Members identical

  •  -20% Mendocino Solar Motor Kit

    Mendocino Solar Motor Kit

    Out of stock

    When you see a Mendocino motor for the first time, you can't help but be fascinated. It floats in the air and spins by itself, seemingly without any source of energy. The functional principle is actually quite simple. The Mendocino motor is a magnetically levitating electric motor powered by solar energy. The solar panels supply current to the coils mounted on the shaft, which generates a magnetic field. The strong magnet attached to the base (the housing) provides a magnetic force that causes rotation. Thanks to the unique magnetic suspension, there is almost no friction. Make sure you have enough light! The stronger the light source, the faster it spins! Specifications Rotation speed 300-1,500 r/min Dimensions 5.31 x 2.76 x 2.76" (13.5 x 7 x 7 cm) Weight approx. 300 g

    Out of stock

    $56.00$45.00

    Members identical

  •  -14% Verbeterde T-962 Infrarood reflow-oven (Elektor versie)

    Upgraded T-962 Infrared Reflow Oven (Elektor Version)

    Out of stock

    This upgraded version (available exclusively from Elektor) contains the following improvements: Enhanced protective earthing (PE) for furnace chassis Extra thermal insulation layer around furnace to reduce odors The infrared IC heater T-962 is a microprocessor-controlled reflow oven that you can use for effectively soldering various SMD and BGA components. The whole soldering process can be completed automatically and it is very easy to use. This machine uses a powerful infrared emission and circulation of the hot air flow, so the temperature is being kept very accurate and evenly distributed. A windowed drawer is designed to hold the work-piece, and allows safe soldering techniques and the manipulation of SMDBGA and other small electronic parts mounted on a PCB assembly. The T-962 may be used to automatically rework solder to correct bad solder joints, remove / replace bad components and complete small engineering models or prototypes. Features Large infrared soldering area  Effective soldering area: 180 x 235 mm; this increases the usage range of this machine drastically and makes it an economical investment. Choice of different soldering cycles Parameters of eight soldering cycles are pre defined and the entire soldering process can completed automatically from Preheat, Soak and Reflow through to cool down. Special heat up and temperature equalization with all designs Uses up to 800 Watts of energy efficient Infrared heating and air circulation to re-flow solder. Ergonomic design, practical and easily operated Good build quality but at the same time light weight and a small footprint allows the T-962 to be easily bench positioned transported or stored. Large number of available funtions The T-962 can solder most small parts of PCB boards, for example CHIP, SOP, PLCC, QFP, BGA etc. It is the ideal rework solution from single runs to on-demand small batch production. Specifications Max. soldering area 180 x 235 mm (7.1 x 9.3") Rated power 800 W Processing time 1~8 minutes Power supply 220 V AC/60 Hz Dimensions 31 x 29 x 17 cm (12.2 x 11.4 x 6.7") Weight 6.2 kg Downloads User Manual GitHub

    Out of stock

    $310.00$266.00

    Members identical

  • Dragino LPS8 Indoor LoRaWAN Gateway (EU868)

    Dragino Dragino LPS8 Indoor LoRaWAN Gateway (EU868)

    The LPS8 is an open source multi-channel LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi or Ethernet. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates. The LPS8 uses Semtech Packet Forwarder and is fully compatible with the LoRaWAN protocol. It includes a SX1308 LoRa concentrator, which provides 10 programmable parallel demodulation paths. LPS8 has pre-configured standard LoRaWAN frequency bands to use for different countries. User can also customized the frequency bands to use in their own LoRa network. Features Linux-based OpenWrt system Managed by intuitive Web GUI, SSH via LAN of WiFi Remote access with Reverse-SSH Emulates 49x LoRa demodulators LoRaWAN Gateway 10 programmable parallel demodulation paths Applications Logistiek and Supply Chain Management Smart Buildings & Home Automation Smart Cities Smart Agriculture Smart Factory Smart Metering Specifications Power Input via USB Type-C (5 V, 2 A) 1x USB host port 1x RJ45 (10/100 Mbit/s) 1x 2.4 GHz WiFi (802.11 b/g/n) LoRa Specs: 1x SX1308 Lora Concentrator 2x 1257 LoRa Transceiver Downloads Datasheet User Manual Source code on GitHub Dragino LoRa Gateway Selection Guide Use Dragino LPS8 as Helium Data-Only Hotspot Dragino LoRaWAN Gateway Setup Dragino Gateways/Hotspots with Helium Tutorial Firmware

    $222.00

    Members $199.80

  •  -32% Useless Box

    Useless Box

    You've seen them online or in hilarious video's your colleagues sent you and now you can build one yourself, as a simple solderless kit! Including all you need except the batteries. Don't know it? There is a lot you can say about this kit, but actually all you need to do is watch a video and fall in love! A must have for each office!

    $34.00$23.00

    Members identical

  • Sand Clock Kit (based on Raspberry Pi Pico)

    Elektor Labs Sand Clock Kit (based on Raspberry Pi Pico)

    Raspberry Pi-based Eye Catcher A standard sand clock just shows how time passes. In contrast, this Raspberry Pi Pico-controlled sand clock shows the exact time by “engraving” the four digits for hour and minute into the layer of sand. After an adjustable time the sand is flattened out by two vibration motors and everything begins all over again. At the heart of the sand clock are two servo motors driving a writing pen through a pantograph mechanism. A third servo motor lifts the pen up and down. The sand container is equipped with two vibration motors to flatten the sand. The electronic part of the sand clock consists of a Raspberry Pi Pico and an RTC/driver board with a real-time clock, plus driver circuits for the servo motors. A detailed construction manual is available for downloading. Features Dimensions: 135 x 110 x 80 mm Build time: 1.5 to 2 hours approx. Included 3x Precut acrylic sheets with all mechanical parts 3x Mini servo motors 2x Vibration motors 1x Raspberry Pi Pico 1x RTC/driver board with assembled parts Nuts, bolts, spacers, and wires for the assembly Fine-grained white sand

    $70.00

    Members $63.00

  • Makerfabs RC522 RFID Reader met Cards Kit (13.56 MHz)

    Makerfabs Makerfabs RC522 RFID Reader with Cards Kit (13.56 MHz)

    Out of stock

    This RC522 RFID Kit includes a 13.56 MHz RF reader module that uses an RC522 IC and two S50 RFID cards to help you learn and add the 13.56 MHz RF transition to your project. The MF RC522 is a highly integrated transmission module for contactless communication at 13.56 MHz. RC522 supports ISO 14443A/MIFARE mode. The module uses SPI to communicate with microcontrollers. The open-hardware community already has a lot of projects exploiting the RC522 – RFID Communication, using Arduino. Features Operating Current: 13-26 mA/DC 3.3 V Idle Current: 10-13 mA/DC 3.3 V Sleep Current: Peak Current: Operating Frequency: 13.56 MHz Supported card types: mifare1 S50, mifare1 S70 MIFARE Ultralight, Mifare Pro, MIFARE DESFire Environmental Operating Temperature: -20-80 degrees Celsius Environmental Storage Temperature: -40-85 degrees Celsius Relative humidity: relative humidity 5% -95% Reader Distance: ≥50 mm/1.95" (Mifare 1) Module Size: 40×60 mm/1.57*2.34" Module interfaces SPI Parameter Data transfer rate: maximum 10 Mbit/s Included 1x RFID-RC522 Module 1x Standard S50 Blank Card 1x S50 special-shaped card (as shown by the keyring shape) 1x Straight Pin 1x Curved Pin Downloads Arduino Library MFRC522 Datasheet MFRC522_ANT Mifare S50

    Out of stock

    $7.00

    Members $6.30

  •  -28% Elektor US-Style Sirene Kit

    Elektor Labs Elektor US-Style Siren Kit

    A great way to explain the workings of an electronic circuit is to position the discrete parts on the board exactly as in the schematic. Press the button and this "Elektor Classic" responds with 1 of 3 siren sounds: police, ambulance, or fire brigade. The kit is composed of through-hole parts only and includes a wooden desktop stand. A full explanation of the circuit operation appears on the back of the circuit board. Features Realistic Sound from Onboard Speaker Unique PCB Layout Equals Schematic Elektor Heritage Circuit Symbols Tried & Tested by Elektor Labs Educational & Geeky Project Through-Hole Parts Only Included Printed Circuit Board All Components Wooden Desktop Stand

    $39.00$28.00

    Members identical

  • BBC micro:bit v2

    BBC micro:bit v2

    Differences between micro:bit v1 and micro:bit v2 The BBC micro:bit v2 is equipped with BLE Bluetooth 5.0 It has a Power off button(push and hold power button) MEMS microphone with a LED indicator Onboard speaker Touch-sensitive logo pin LED power indicator A notched edge connector for easier connections.

    $28.00

    Members $25.20

  • TV-B-Gone Kit – Universal TV Remote

    TV-B-Gone Kit - Universal TV Remote

    The TV-B-Gone universal remote control allows you to turn virtually any TV On or OFF. You control when you see TV, rather than what you see. The TV-B-Gone Keychain remote is so small that it easily fits in your pocket so that you have it handy whenever you need it, wherever you go: bars, restaurants, laundromats, ballparks, arenas, etc.The TV-B-Gone Kit is a great way to teach about electronics. When soldered together, it allows you to turn off almost any television within 150 feet or more. It works on over 230 total power codes – 115 American/Asian and another 115 European codes. You can select which zone you want during kit assembly.This is an unassembled kit which means that soldering and assembly is required – but it’s very easy and a great introduction to soldering in general.This kit makes the popular TV-B-Gone remote more fun because you created it yourself with some basic soldering and assembly! Show your friends and family how technologically savvy you are, and entertain them with the power of the TV-B-Gone!The kit is powered by 2x AA batteries and the output comes from 2x narrow beam IR LEDs and 2x wide-beam IR LEDs.IncludedAll required parts/componentsRequiredTools, soldering iron, and batteriesDownloadsGitHub

    $34.00

    Members $30.60

  • Cytron 10Amp 5-30 V DC Motor Driver

    Cytron Cytron 10Amp 5-30 V DC Motor Driver

    DC brushed motors are the most commonly used and widely available motors in the market. The Cytron 10 Amp 5-30 V DC Motor Driver will help you add functionality to your DC motor. It supports both sign-magnitude PWM signal and locked-antiphase. It is compatible with full solid-state components resulting in higher response time and eliminates the wear and tear of the mechanical relay. Features Supports motor voltage from 5 V to 30 V DC Current up to 13 A continuous and 30 A peak 3.3 V and 5 V logic level input Compatible with Arduino and Raspberry Pi Speed control PWM frequency up to 20 kHz Fully NMOS H-Bridge for better efficiency No heat sink is required Bi-directional control for one Brushed DC motor Regenerative Braking Downloads User Manual Arduino Library

    $20.00

    Members $18.00

  • Cytron Maker Pi RP2040 - Robotica met Raspberry Pi RP2040

    Cytron Cytron Maker Pi RP2040 - Robotics with Raspberry Pi RP2040

    Cytron Maker Pi RP2040 features the first microcontroller designed by Raspberry Pi – RP2040, embedded on a robot controller board. This board comes with dual channel DC motor driver, 4 servo motor ports and 7 Grove I/O connectors, ready for your next DIY robot / motion control project. Now you can build robot, while trying out the new RP2040 chip. The DC motor driver onboard is able to control 2x brushed DC motors or 1x bipolar/unipolar stepper motor rated from 3.6 V to 6 V, providing up to 1 A current per channel continuously. The built-in Quick Test buttons and motor output LEDs allow functional test of the motor driver in a quick and convenient way, without the need of writing any code. Vmotor for both DC and servo motors depends on the input voltage supplied to the board. Maker Pi RP2040 features all the goodness of Cytron's Maker series products. It too has lots of LEDs useful for troubleshooting (& visual effects), is able to make quite some noise with the onboard piezo buzzer and comes with push buttons ready to detect your touch. There are three ways to supply power to the Maker Pi RP2040 – via USB (5 V) socket, with a single cell LiPo/Li-Ion battery or through the VIN (3.6-6 V) terminals. However only one power source is needed to power up both controller board and motors at a time. Power supply from all these power sources can all be controlled with the power on/off switch onboard. Cytron Maker Pi RP2040 is basically the Raspberry Pi Pico + Maker series' goodness + Robot controller & other useful features. Therefore this board is compatible with the existing Pico ecosystem. Software, firmware, libraries and resources that are developed for Pico should work seamlessly with Cytron Maker Pi RP2040 too. CircuitPython is preloaded on the Maker Pi RP2040 and it runs a simple demo program right out-of-the-box. Connect it to your computer via USB micro cable and turn it on, you will be greeted by a melody tune and LEDs running light. Press GP20 and GP21 push buttons to toggle the LEDs on/off, while controlling any DC and servo motors connected to it to move and stop. With this demo code, you get to test the board the moment you receive it! While connected to your computer, a new CIRCUITPY drive appears. Explore and edit the demo code (code.py & lib folder) with any code editor you like, save any changes to the drive and you shall see it in action in no time. That's why we embrace CircuitPython – it's very easy to get started. Wish to use other programming lauguages? Sure, you are free to use MicroPython and C/C++ for Pico/RP2040. For those of you who loves the Arduino ecosystem, please take a look at this official news by Arduino and also the unofficial Pico Arduino Core by Earle F. Philhower. Features Powered by Rapberry Pi RP2040 Dual-core Arm Cortex-M0+ processor 264 KB internal RAM 2 MB of Flash memory the exact same specifications with Raspberry Pi Pico Robot controller board 4x Servo motors 2x DC motors with quick test buttons Versatile power circuit Automatic power selection: USB 5 V, LiPo (1-cell) or Vin (3.6-6 V) Built-in 1-cell LiPo/Li-Ion charger (over-charged & over-discharged protection) Power on/off switch 13x Status indicator LEDs for GPIO pins 1x Piezo buzzer with mute switch 2x Push button 2x RGB LED (Neopixel) 7x Grove ports (flexible I/O options: digital, analog, I²C, SPI, UART...) Preloaded with CircuitPython by default Mouting holes 4x 4.8 mm mounting hole (LEGO pin compatible) 6x M3 screw hole

    $19.00

    Members $17.10

  • Seeed Studio RFM95 Ultra-long LoRa Transceiver Module (EU868)

    Seeed Studio Seeed Studio RFM95 Ultra-long LoRa Transceiver Module (EU868)

    The RFM95 is a LoRa / SigFox module to be used with Arduino / ESP32 / Raspberry Pi and many other. With ideal conditions, you can get ranges up to 2km+ while having only small power consumption. It is equipped with the LoRa long range modem that provides ultra-long range spread spectrum communication and high interference immunity. Using the patented LoRa™ modulation technique RFM95 can achieve a sensitivity of over -148dBm using a low-cost crystal and bill of materials. The high sensitivity combined with the integrated +20 dBm power amplifier yields industry leading link budget making it optimal for any application requiring range or robustness. Features maximum link budget: 168 dB +20 dBm - 100 mW constant RF output vs. V supply +14 dBm high efficiency PA Programmable bit rate up to 300 kbps. High sensitivity: down to -148 dBm. Bullet-proof front end: IIP3 = -12.5 dBm. Built-in bit synchronizer for clock recovery. Excellent blocking immunity. Low RX current of 10.3 mA, 200 mA register retention. Fully integrated synthesizer with a resolution of 61 Hz. FSK, GFSK, MSK, GMSK, LoRa™ and OOK modulation. Preamble detection. 127 dB Dynamic Range RSSI. Automatic RF Sense and CAD with ultra-fast AFC. Packet engine up to 256 bytes with CRC. Built-in temperature sensor Low battery indicator. Dimensions: 16 x 16 mm Applications Automated Meter Reading Home and Building Automation Wireless Alarm and Security Systems Industrial Monitoring and Control Long range Irrigation Systems

    $18.00

    Members $16.20

  • Sipeed Maixduino Kit voor RISC-V AI + IoT

    Seeed Studio Sipeed Maixduino Kit for RISC-V AI + IoT

    Out of stock

    MAIX is Sipeed's purpose-built product series designed to run AI at the edge. Move AI models from cloud down to devices on the edge of the network where they can run faster, at lower cost, and with greater privacy. MAIX isn't just a hardware solution, it combines custom hardware, open software, and state-of-the-art AI algorithms. Different kinds of dev. boards, kits, peripherals as well as wide compatibility enable rapid and agile prototype development, make AIoT projects much easier. And thanks to MAIX' s performance, small footprint, low power, and low cost, it enables the broad deployment of high-quality Edge AI. Applications Smart Home applications like robot cleaners, smart speakers, electronic door locks, household monitoring etc. Medical Industry applications like Auxiliary diagnosis and treatment, medical image recognition, emergency alarm etc. Smart Industry applications like industrial machinery, intelligent sorting, monitoring of electrical equipment, etc. Education applications like educational robots, intelligent interactive platforms, educational efficiency inspection, etc. Agriculture applications like agricultural monitoring, pest and disease monitoring, automated control, etc. Features CPU: RISC-V Dual Core 64bit, with FPU; 400MHz neural network processor QVGA@60FPS/VGA@30FPS image identification Onboard ESP32 module support 2.4G 802.11. b/g/n and Bluetooth 4.2 Arduino Uno form factor, Arduino compatible interface Onboard omnidirectional I²S digital output MEMS Microphone 24P 0.5mm FPC connector for DVP Camera 8-bit MCU LCD 24P 0.5mm FPC connector Support self-elastic micro SD card holder Reset and boot button; 3W DAC+PA Audio output Just connect the USB Type-C cable to complete the download Machine vision based on convolutional neural network High performance microphone array processor for machine hearing Support MaixPy IDE, Arduino IDE, OpenMV IDE, and PlatformIO IDE Support Tiny-Yolo, Mobilenet and TensorFlow Lite for deep learning Technical Specifications Master module Sipeed MAIX-I AIoT module Power Input USB Type-CDC-DC step-down circuit:support 6-12V input; Provide 5V 1.2A output Micro SD Card (TF card) slot Support Self-elastic card holder Onboard MEMS microphone MSM261S4030H0 is an omnidirectional, Bottom-ported, I²S digital output MEMS Microphone. It has high performance and Reliability. DVP Camera interface 24P 0.5mm FPC connector LCD connector 8bit MCU LCD 24P 0.5mm FPC connector Audio output DAC+PATM8211: 16 bit dynamic range;Low harmonic distortionNS4150: 3W output power; Up to 90% efficiency ESP32 module Support 2.4G 802.11.b/g/n802.11 n (2.4 GHz) speeds up to 150 MbpsBluetooth v4.2 full standard, including traditional Bluetooth (BR/EDR) and Bluetooth Low Energy (BLE) Supply voltage of external power supply 4.8V ~ 5.2V Supply current of external power supply >600mA Temperature rise Range of working temperature -30℃ ~ 85℃ MCU: ESP8285 Tensilica L106 32-bit MCU Wireless Standard 802.11 b/g/n Frequency Range 2400Mhz - 2483.5Mhz TX Power(Conduction test) 802.11.b: +15dBm802.11.g: +10dBm(54Mbps)802.11.n: +10dBm (65Mbps) Antenna Connector IPEX 3.0x3.0mm Wi-Fi mode Station/SoftAP/SoftAP+Station Contents 1x Maixduino Development Board 1x GC0328 Camera Module 1x 2.4 inch TFT Display

    Out of stock

    $37.00

    Members $33.30

  • makerdiary nRF52840 MDK USB Dongle incl. Case

    Make makerdiary nRF52840 MDK USB Dongle incl. Case

    The Makerdiary nRF52840 Dongle with Case is a small and low-cost development platform enabled by the nRF52840 multiprotocol SoC in a convenient USB dongle form factor. The USB Dongle is fully multiprotocol capable with full protocol concurrency. It has protocol support for Bluetooth 5, Bluetooth mesh, Thread, ZigBee, IEEE 802.15.4, ANT and 2.4 GHz proprietary stacks. Alternatively the USB Dongle can act as a Network Co-Processor (NCP) with a simple connection to a PC or other USB enabled device. Features Low cost USB dongle supporting Bluetooth 5, Bluetooth mesh, Thread, ZigBee, IEEE 802.15.4, ANT and 2.4 GHz proprietary stacks Shipped with USB enabled bootloader and OpenThread NCP firmware Programming via nRF Connect for Desktop or nRFUtil OpenThread Border Router supported Thread Network Sniffer with Wireshark Thread Topology Monitor Nordic nRF52840 System-on-Chip ARM Cortex-M4F processor optimized for ultra-low power operation Combining Bluetooth 5, Bluetooth Mesh, Thread, IEEE 802.15.4, ANT and 2.4 GHz proprietary On-chip USB 2.0 (Full speed) controller ARM TrustZone Cryptocell 310 security subsystem 1 MB FLASH and 256 kB RAM 1 user-programmable button 1 user-programmable RGB LED Integrated 2.4 GHz chip antenna Convenient USB dongle form factor Dimensions: 50.8 x 21.1 x 7.6 mm Weight: 6.0g Downloads Wiki

    $34.00

    Members $30.60

  •  -33% Makerfabs PN532 NFC Module V3

    Makerfabs Makerfabs PN532 NFC Module V3

    NFC is a popular technology in recent years. Almost all the high-end phones in the market support NFC. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. This module is built around NXP PN532. NXP PN532 is very popular in the NFC area. Makerfabs developed this module based on the official document. A library for this module is available. Features Small dimension and easy to embed into your project Support I²C, SPI, and HSU (High-Speed UART), easy to change between those modes Support RFID reading and writing, P2P communication with peers, NFC with Android phone Up to 5~7 cm reading distance On-board level shifter, Standard 5 V TTL for I²C and UART, 3.3 V TTL SPI Arduino compatible, plugin and play with our shield RFID reader/writer supports Mifare 1k, 4k, Ultralight, and DESFire cards ISO/IEC 14443-4 cards such as CD97BX, CD light, Desfire, P5CN072 (SMX) Innovision Jewel cards such as IRT5001 cards FeliCa cards such as RCS_860 and RCS_854 Downloads Usage NFC Library

    $15.00$10.00

    Members identical

  • CircuitMess Nibble – DIY Game Console

    CircuitMess CircuitMess Nibble - DIY Game Console

    Features Processor: 32-bit, 160MHz Storage: 4 MB RAM: 80 KB Display: 1.4″ 128 x 128 Full-color TFT Connectivity: WiFi Build time: 2 hours Programming: C++ (Arduino), CircuitBlocks, Python Parts Main circuit board Acrylic casing Metal soldering iron stand Sponge Soldering iron Solder wire Cross screwdriver AAA alkaline batteries LCD display Micro USB cable Bag with small components Battery holder Here you can find the guide to assemble your CircuitMess Nibble – DIY Game Console.

    $95.00

    Members $85.50

  • Dragino DLOS8 Outdoor LoRaWAN Gateway (EU868)

    Dragino Dragino DLOS8 Outdoor LoRaWAN Gateway (EU868)

    The DLOS8 is an open-source outdoor LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via Ethernet, WiFi or 3G. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates. The DLOS8 uses Semtech packet forwarder and fully compatible with LoRaWAN protocol. It includes an SX1301 LoRaWAN concentrator, which provides ten programmable parallel demodulation paths. DLOS8 has pre-configured standard LoRaWAN frequency bands to use for different countries. User can also customize the frequency bands to use in their LoRaWAN network. DLOS8 can communicate with ABP LoRaWAN end node without LoRaWAN server. The system integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service. Features Managed by SSH via LAN or WiFi, Web GUI Open Source OpenWrt system Emulates 49x LoRa demodulators Outdoor LoRaWAN Gateway LoRaWAN packet filtering Ten programmable parallel demodulation paths Farseeing LED indicator External fibreglass antenna Built-in GPS module for location & timing 802.3af PoE IP65 Lighting Protection Power Consumption:12 V, 300 mA ~ 500 mA 1x 10M / 100M RJ45 Ports 1x USB host port 2.4G WiFi (802.11 bgn) Applications Logistics and Supply Chain Management Smart Buildings & Home Automation Smart Metering Smart Cities Smart Agriculture Smart Factory Downloads Datasheet User Manual Firmware Mechanical

    $443.00

    Members $398.70

  •  -49%Last stock! BBC micro:bit experimenteer kit

    Elektor Labs BBC micro:bit Experimenter's Kit

    2 in stock

    Kit of parts for the experiments with the BBC micro:bit (not included in this kit) published in the book BBC micro:bit – 35 Touch Develop & microPython Projects. Kit contents 4x LED 4x 270 ohm resistor 5x wire (male-female) 2x wire (male-male) 3x Button 3x 10 kilo-ohm resistor 1x TMP36 temperature sensor 1x Buzzer 1x Light dependent resistor 1x RGB LED 1x BC337 transistor 1x 680 ohm resistor 1x 3 V DC motor 1x ML8511 UV sensor module 1x Mini servo 1x Small breadboard 1x BBC micro:bit edge connector 1x BBC micro:bit adapter board 1x Mounting plate

    2 in stock

    $45.00$23.00

    Members identical

  • The XL741 Discrete Op-Amp Kit

    Evil Mad Science The XL741 Discrete Op-Amp Kit

    Out of stock

    The XL741 kit is sold as an easy-to-build soldering kit. It includes the circuit board, resistors, transistors and capacitor that make up the electrical circuit as well as printed assembly instructions. The kit also comes complete with the 'IC Leg' stand, and eight colour-coded thumbscrew terminal posts. To build the XL741 kit, fundamental electronic soldering skill and tools are required. Soldering tools are not included, and you will need to use your own. You will need: a soldering iron, solder and small ('flush') wire clippers, as well as a Phillips head screwdriver The kit features easy construction and should take roughly an hour to build. Kit size The XL741 kit printed circuit board is 5.215' x 3.175' (13.25 cm x 8.06 cm) in area, and (nominally) 0.100' (2.54 mm) thick. Including the 'Integrated Circuit Legs' stand and terminal posts, the overall size of the assembled kit is 5.215' x 3.9' x 1.70' (13.25 cm x 9.9 cm x 4.3 cm). Materials and construction The decorative stand is smooth to the touch and made of anodised aluminium. The circuit board in the kit is extra thick for rigidity and made with a matte-black solder mask finish. It comes pre-fitted with eight 8-32 threaded inserts for the terminal posts. All materials (including the circuit board and stand) are RoHS compliant (lead-free). The included terminal post screws are stainless steel thumbscrews with colour-coded plastic caps (1 red, 1 black, 6 grey).

    Out of stock

    $50.00

    Members $45.00

  •  -33% Makerfabs NFC Stickers (6 pcs)

    Makerfabs Makerfabs NFC Stickers (6 pcs)

    Features NFC chip material: PET + Etching antenna Chip: NTAG216 (compatible with all NFC phones) Frequency: 13.56 MHz (High Frequency) Reading time: 1 - 2 ms Storage capacity: 888 bytes Read and write times: > 100,000 times Reading distance: 0 - 5 mm Data retention: > 10 years NFC chip size: Diameter 30 mm Non-contact, no friction, the failure rate is small, low maintenance costs Read rate, verification speed, which can effectively save time and improve efficiency Waterproof, dustproof, anti-vibration No power comes with an antenna, embedded encryption control logic, and communication logic circuit Included 1x NFC Stickers (6-color kit)

    $12.00$8.00

    Members identical

This category offers a wide spectrum of platforms to choose from. They all have different features and you can choose the platform that best suits your needs or project.

Login

Forgot password?

Don't have an account yet?
Create an account