DSO-TC3 combines a digital oscilloscope, electronic component tester, signal generator, continuity test, voltage test, temperature and humidity measurement, infrared decoding and other functions are skillfully integrated. It is equipped with a 2.4" color TFT display and a built-in rechargeable lithium battery for mobile use. Specifications (Oscilloscope) The oscilloscope has a real-time sampling rate of 10 MSa/s and a bandwidth of 500 kHz. With complete trigger function (single, normal, automatic), no matter if you’re using periodic analog signals or non-periodic digital signals. Maximum measured voltage signal is 400 V. Equipped with efficient AUTO, the measured waveform can be displayed without cumbersome adjustments. Real-time sample rate 10 MSa/s Bandwidth 500 kHz Input resistance 1 MΩ Coupling method AC/DC Test voltage range 400 V Vertical Sensitivity (x1) 10 mV-10 V Horizontal time base range 1us-10s Trigger mode Auto/Normal/Single Trigger type Rising edge/Falling edge Waveform Freeze Yes Automatic measurement Yes Specifications (Component Tester) The instrument can automatically identify and measure various transistors, including NPN and PNP triodes, N-channel and P-channel mosfet, junction mosfet, diodes, dual diodes, thyristors, and resistors, inductors, capacitors and other passive components. Automatic detection of pin definition. Automatically analyze NEC protocol infrared code. Other functional modes: Including circuit continuity test, 0-40 V input voltage measurement, PWM output, 0-32 V regulated diode measurement, DS18B20 temperature sensor measurement, DHT11 temperature and humidity sensor measurement, etc. Specifications (Signal Generator) The signal generator has a total of 6 waveforms to choose from, with adjustable frequency and amplitude. Sine wave 1-100 KHz/0-3.3 V/50% Square wave 1-100 KHz/3.3 V/50% Pulse wave 1-100 KHz/3.3 V/0-100% Triangle wave 1-100 KHz/0-3.3 V/50% Ramp 1-100 KHz/0-3.3 V/0-100% DC 0-3.3 V Included 1x DSO-TC3 1x P6100 Oscilloscope Probe (100 MHz) 3x Test Hooks 1x Adapter 1x USB-C Cable 1x Manual Downloads Manual Firmware V0.3

Read more less

The FNIRSI SWM-10 is an efficient, practical and easy-to-carry handheld spot welder with a built-in 5000 mAh lithium battery that also functions as a power bank. The double-pulse spot welding technology makes the welding more stable and firm. Features 5000 mAh lithium battery for long battery life Fast charging power bank High-resolution 1.8" TFT LCD color screen Built-in intelligent temperature control sensor, over temperature, low voltage and short circuit protection Customized settings for preheat, pulse, interval and number of connection points make welding more stable and safer Can weld nickel sheets, iron sheets, stainless steel sheets, etc. The maximum welding thickness is 0.25 mm, and the welding current is 1200 A. Specifications Capacity 5000 mAh Charge 5 V/2.1 A Discharge 5 V/2.1 A Welding materials Nickel sheet, iron sheet, stainless steelsheet, aluminum sheet Welding thickness 0.1-0.25 mm Maximum welding current 1200 A Gear 4 combination gear adjustment Dimensions 155 x 82 x 28 mm Included 1x FNIRSI SWM-10 Spot welder 2x Spot welding pens 1x Nickel sheet 2x Spare needles 1x USB cable 1x Manual Downloads Manual Firmware V1.4

Read more less

The FNIRSI 2C23T is a fully functional, highly practical 3-in-1 dual channel digital oscilloscope with a high resolution 2.8-inch LCD display (320 x 240 pixels) designed for the maintenance and development industry. This device is equipped with 3 main functions: oscilloscope, multimeter and signal generator. The oscilloscope has an FPGA+MCU+ADC hardware architecture with a sampling rate of 50 MS/s, an analog bandwidth of 10 MHz and a built-in high-voltage protection module that supports the measurement of peak voltages of ±400 V maximum. The multimeter has a 4-digit 10000-point RMS value and supports AC/DC voltage and current measurements, as well as capacitance, resistance, diode, on/off and other measurement functions. Equipped with a built-in DDS function signal generator, it can output 7 kinds of function signals, with a maximum output of 2 MHz for all signals and a step of 1 Hz; the output frequency, amplitude and duty cycle are adjustable. The built-in 3000 mAh rechargeable lithium battery achieves a standby time of up to 6 hours. Features 2-ch oscilloscope 10 MHz bandwidth 50 MS/s real-time sampling rate 7 signal waveforms 10000 counts 2.8' HD color display (320 x 240 pixels) Dimensions: 167 x 89 x 35 mm Weight: 300 g Specifications Oscilloscope Dual channel, 2x 10 MHz bandwidth, 50 MS/s real-time sampling rate Maximum measured voltage: ±400 V FPGA+ADC+MCU high-performance hardware architecture, capturing waveform details without loss Equipped with complete triggering functions (auto, single, normal) Equipped with efficient automatic adjustment, the measured waveform can be displayed without complicated adjustment Save waveform screenshots, supports exporting images to a computer, facilitate secondary waveform analysis Multimeter 4-bit integer 9999 counting True RMS measurement Identification of voltage, current, capacitance, resistance, diode, on/off, and zero live wire Maximum input voltage: AC 750 V, DC 1000 V Automatic range, intelligent anti burning Data retention, color screen digital display Signal Generator 7 signal waveforms: sine wave, square wave, triangular wave, full wave, half wave, noise wave, DC Output frequency: 1 Hz-2 MHz Output amplituade: 0.1-3.3 V Output duty cycle: 0-100% Included 1x FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope 1x P6100 oscilloscope probes (10X) 1x Multimeter probe 1x Crocodile clip probe 1x USB-C charging cable 1x Manual Downloads Manual

Read more less

The FNIRSI LCR-ST1 is a compact, multifunctional, and smart LCR tester that supports automatic measurements of resistance, capacitance, inductance, diode testing, and continuity. Its 1.14-inch color display combined with a convenient magnetic adsorption function enhances ease of use, while the built-in 250 mAh lithium battery ensures long-lasting performance. The device supports three frequency ranges (100 Hz, 1 kHz and 10 kHz) and offers 0.3 V and 0.6 V RMS test levels for versatile testing applications. The unique tweezer-shaped design of the LCR-ST1 is ideal for delicate tasks in confined spaces and enables fast and accurate testing of electronic components. Its light weight and portable design make it an invaluable tool for both field and laboratory use. Whether you are an experienced engineer or just starting out in electronics, the LCR-ST1 delivers reliable and accurate measurement results, allowing you to complete your tasks with greater efficiency and precision. Features Offers 3 test frequencies (100 Hz, 1 kHz, 10 kHz) and 2 test voltage levels. Features automatic component identification for faster and more reliable measurements. High-resolution 1.14-inch color display for clear readouts. Supports automatic data recording and storage. The tweezer tips are made from gold-plated brass for enhanced durability and conductivity. Specifications Resistance Range 10 mΩ – 10 MΩ Capacitance Range 1 pF – 22 mF Inductance Range 1 μh – 10 H Diode On voltage 0.7 V Frequency Test 100 Hz, 1k Hz, 10 KHz Level Test 0.3 V, 0.6 V RMS Parameter Display ESR, D value, Q value, Z value, X value Display 1.14" HD color screen Charging Interface USB-C, 5 V/1 A Power Supply Built-in 250 mAh lithium battery Auto Recognition Measurement Yes Replaceable Tweezer Head Yes Auto Shutdown Yes Data Hold Yes History Record Connect to PC to view and export Dimensions 28 x 19 x 150 mm Weight 41 g Included 1x LCR-ST1 SMD Tweezers 2x Hook Tips 1x Magnetic Patch 1x USB cable 1x Tool bag 1x Manual Downloads Manual Firmware V1.6

Read more less

The FNIRSI DPOX180H is a cost-effective handheld dual-channel digital phosphor oscilloscope and signal generator. The oscilloscope has a real-time sampling rate of 500 MS/s and an analog bandwidth of 180 MHz. The measurement results are displayed on the high-contrast 2.8-inch IPS full-view LCD screen with digital fluorescence technology. Features 2-ch handheld oscilloscope & DDS signal generator 180 MHz bandwidth 500 MS/s sampling rate 20 MHz signal generator Innovative digital trigger system Cursor measurement function 5 mV sensitivity 50000 wfm/s waveform refresh rate 2.8" IPS full-vision high-definition display Built-in 4.2 V/3000 mAh lithium battery Automatic shutdown setting High-voltage anti-burning protection Specifications Nummer of channels 2 Analog bandwidth 180 MHz Maximum sampling rate 500 MS/s Input coupling DC/AC Rise time 2.5s Storage depth 120 Kpts Input impedance 1 MQ-18 PF Vertical sensitivity 5 mV-10 V (1X) Time base range 5 nS~50 S DC accuracy ±2% Time accuracy +0.01% Trigger detection Digital trigger Trigger mode Auto/Single/Normal Trigger edge Rising/Falling Measurement range 40 mV~80 V (1X) Screenshot storage 90 Capture signal 500 Screen size 2.8 inch Screen resolution 320 x 240 Display technology IPS full view Expansion interface USB transmission interface Auto power off 5 minutes - 2 hours Firmware upgrade Supported iso image upgrade Charging requirements 5 V/2 A Battery capacity 3000 mAh Standby time 3.5 hours at full charge Signal Generator 14 standard function signals Waveform storage 250 groups Parameter measurement 12 kinds Dimensions 135 x 90 x 40 mm Digital Phosphor Oscilloscope FNIRSI DPOX180H Oscilloscope uses the latest digital phosphor technology to overcome the traditional oscilloscope due to noise caused by the waveform burr feeling. Color temperature display function can more clearly see the distribution of the signal, probability characteristics and the rise and fall time of the step signal fast and slow. X-Y mode with digital phosphor technology for comparison of amplitude, frequency and phase of two groups of signals. DDS Function Signal Generator Built-in 20 MHz DDS function signal generator, with 14 kinds of standard function signals, output amplitude fixed at 1 VPP, sine wave frequency of 20 MHz, other waveform frequency of 10 MHz, adjustable frequency step of 1 Hz. Contains the original chopping technology, intercept part of the oscilloscope measurement of complex signals as the output signal of the signal generator, than the traditional signal generator hand-drawn signal more objective and realistic. Included 1x FNIRSI DPOX180H phosphor oscilloscope 2x Probes (200 MHz) 1x USB power supply 1x USB cable 1x Manual Downloads Manual Firmware V40

Read more less

The FNIRSI FNB58 USB tester (with Bluetooth) is a comprehensive and very accurate USB voltage and current meter. It features a 2.0-inch full-color HD TFT display, built-in USB-A, micro USB and USB-C interface. With this device you can measure the power supply or power consumption of products or the charging power of cell phones and power supplies. You can also determine the fast charging protocol of chargers. Features USB-A and USB-C interface 2.0" HD display Data at a glance Wide compatibility Ultra-precise data detection Play with fast charging technology Automatic protocol detection (PD2.0, 3.0, 3.1, PPS, QC2.0, 3.0, FCP, SCP, AFC, PE, DASH VOOC, SuperVOOC and more) Simple user interface, easy to operate 4 function curve displays (real-time voltage and current curve, offline curve recording, D+/D- voltage curve, high-speed power supply ripple measurement) Cable detection 10 groups of energy recording battery capacity calculation PC connectivity for data logging and firmware updates Bluetooth app for Android devices Specifications Voltage range 4-28 V Current range 0-7 A Power range 0-120 W Load equivalent internal resistance 0-9999.9 Ω D+/D- voltage 0-3.3 V Capacity 0-9999.99 Ah Power consumption 0-9999.99 Wh Cable resistance 0-9999.9 Ω Interfaces micro USB, USB-A, USB-C Dimensions 42 x 13 x 82 mm Downloads Manual Firmware V0.68

Read more less

The perfect tool for quick repairs The FNIRSI HS-01 is a powerful, adjustable smart soldering iron with a built-in 0.87-inch OLED display that quickly reaches temperatures between 80-420°C (180-780°F). The display shows all important information, including the status of the temperature level, the set temperature, the supply voltage and the power percentage. You can set the input voltage from 9-20 V directly in the menu according to your needs. The integrated sleep mode automatically turns off the iron after 30 minutes. Features 96 W input (DC) 65 W PD power OLED display Constant temperature & fast heating CNC metal integral molding Smart safety anti-scald Mini pocket size Ergonomic design Aluminum material Left/right hand switch Efficient heat radiation Inductive sleep Color: Black Specifications Power 65 W Screen 0.87" OLED Operating voltage 9-20 VDC Power supply USB-C Temperature range 80-420°C (180-780°F) Fast charging protocol PD trigger Dimensions 184 x 20 x 20 mm (7.24 x 0.79 x 0.79') Weight 56 g Power Selection Operating voltage 20 V 15 V 12 V 9 V Operating current ≥3.25 A ≥2.5 A ≥2 A ≥1.5 A Power 65 W 37.5 W 24 W 13.5 W Tin melting time 8s 12s 17s 30s Included 1x FNRISI HS-01 smart soldering iron 6x Soldering iron tips (HS01-BC2, HS01-KR, HS01-K65, HS01-B2, HS01-ILS, HS01-BC3) 1x DC to USB-C power cable 1x Mini soldering iron stand 1x Manual Required Power adapter USB-C cable Downloads Manual Firmware V0.3.s19

Read more less

The FNIRSI DMC-100 is a high-precision 10,000-count True RMS clamp multimeter for engineering, labs, vehicle repairs, and home diagnostics. It measures up to 750 V and 600 A with three modes (routine, waveform, and power) along with NCV detection for added safety. Its 2.0-inch color TFT display offers clear readings, data visualization, and adjustable brightness. A 1500 mAh rechargeable battery with auto power-off ensures long use, while a flashlight, backlight, and data storage enhance usability, making it a reliable tool for professionals and DIYers. Features 10,000-count smart True RMS clamp meter for accurate readings Supports up to 750 V voltage and 600 A current 2.0-inch full-color TFT screen (240 x 320) for clear visuals New UI with data curve display for easy reading at a glance Switch freely between general measurement, waveform display, and power measurement modes Non-contact voltage measurement and zero/fire line identification Measures temperatures from −55°C to 1300°C Built-in battery (3.7 V/1500 mAh) for extended usage Convenient charging and data transmission via USB-C port Includes an LED light, screen backlight, and data-saving capabilities Intelligent automatic shutdown to conserve battery life Easily switch between temperature units (°C/°F) Screen brightness is adjustable for various environments Supports firmware updates to enhance functionality Specifications DC Voltage 9.999V/99.99V/999.9V ±(0.5%+3) AC Voltage 9.999V/99.99V/750.0V ±(1%+3) DC Current 99.99A/600.0A ±(2.5%+10) AC Current 99.99A/600.0A ±(2.5%+10) Resistance 9.999MΩ/999.9KΩ/99.99KΩ/9.999KΩ/999.9Ω ±(1.5%+3) 99.99MΩ ±(1.5%+3) Capacitance 999.9μF/99.99μF/9.999μF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Frequency 9.999MHz/999.9KHz/99.99KHz/9.999KHz/999.99Hz/99.99Hz/9.999Hz ±(0.1%+2) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Continuity Test Yes Diode Yes NCV Yes LIVE Yes Display 2.0" TFT Color Screen Power Supply 3.7 V/1500 mAh Lithium Battery Charging 5 V/1 A (USB-C) Maximum Jaw Size 25 mm Dimensions 193 x 74 x 32 mm Weight 194 g Included 1x FNIRSI DMC-100 Clamp Meter 1x Multimeter pen 1x Temperature probe 1x USB charging cable 1x Manual Downloads Manual Firmware V1.3

Read more less

The updated FNIRSI 2C53T, an enhanced version of its 10 MHz predecessor, is a compact and versatile 3-in-1 device. It combines a dual-channel 50 MHz oscilloscope, a 4.5-digit True RMS multimeter, and a signal generator with 13 waveform types, making it an essential tool for maintenance and research professionals. Oscilloscope: Features 50 MHz bandwidth, 250 MS/s sampling rate, ±400 V protection, FPGA + ARM + ADC architecture, and waveform saving for analysis. Multimeter: 4.5-digit True RMS with 19999 counts, supports AC/DC voltage, current, capacitance, resistance, diode, and continuity measurements. Signal Generator: Outputs 13 signal types up to 50 KHz, with adjustable frequency, amplitude, and duty cycle. With a 2.8-inch LCD, 3000 mAh battery (6-hour runtime), and a portable design, it delivers powerful functionality in a user-friendly package. Specifications Oscilloscope Channels 2 Analog Bandwidth 50 MHz Real-time Sampling Rate 250 MS/s Storage Depth 1 Kpts Impedance 1 MΩ Time Base Range 10ns-20s Vertical Sensitivity 10 mV/div-10 V/div (x1) Maximum Measured Voltage ±400 V Trigger Mode Auto/Normal/Single Trigger Type Rising edge, Falling edge Display Mode Y-T/Rolling/X-Y Coupling Method AC/DC Persistence OFF, 500ms, 1s, ∞ Math 8 Basic Operations + FFT Supported Waveform Screenshot Save, Export Waveform Image, Cursor Measurement, Infinite Afterglow Multimeter DC Voltage 1.9999V/19.999V/199.99V/1000V ±(0.5%+3) AC Voltage 1.9999V/19.999V/199.99V/750.0V ±(1%+3) DC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.2%+3) AC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.5%+3) Resistance 19.999MΩ/1.9999MΩ/199.99KΩ/19.999KΩ ±(0.5%+3) 1.9999KΩ/199.99Ω ±(2.0%+3) Capacitance 999.9uF/99.99uF/9.999uF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Continuity Test Yes Diode Yes Signal Generator 13 Signal Waveforms Sine wave, rectangular wave, sawtooth wave, half wave, full wave, positive step wave, reverse step wave, exponential rise, exponential fall, DC, multi-audio, Sinker pulse, Lorentz wave Output Frequency 0-50 KHz Output Amplitude 0-3 V Output Duty Cycle 0-100% General Display 2.8" HD color screen Resolution 320 x 240 Charging USB-C (5 V/1 A) Battery 3000 mAh Lithium battery Standby Time 6 hours Languages English, Chinese Dimensions 167 x 89 x 35 mm Weight 300 g Differences New vs Old Version Model 2C53T Upgrade 2C53T Predecessor Bandwidth 50 MHz 10 MHz Display Mode Y-T/Rolling/X-Y Y-T/Rolling Math 8 Basic Operations + FFT N/A Cursor Function Yes N/A XY Lissau Graph Yes N/A Afterglow Function Yes N/A Multimeter Accuracy 19999 Counts 9999 Counts Signal Generator 50 KHz 2 MHz Included 1x FNIRSI 2C53T Upgrade Oscilloscope (50 MHz) 2x P6100 Oscilloscope probes (10X) 1x Multimeter probe 1x Alligator clip probe 1x USB-C charging cable 1x Storage bag 1x Manual Downloads Manual Firmware V1.0.3

Read more less

The FNIRSI DWS-200 is a powerful 200 W smart soldering station, ideal for electronic soldering applications. Powered by a switch-mode power supply, it operates smoothly with a wide voltage input range of 100-240 V. The station provides an adjustable temperature range from 100°C to 450°C (212°F to 842°F) and allows for easy switching between °C and °F. To enhance efficiency, it supports up to three preset temperature values and can connect to a soldering iron stand for standby mode activation. The station also features a dynamic temperature curve mode for real-time data monitoring, ensuring precise and consistent performance in demanding soldering tasks. Features Maximum power output of 200 W, allowing for fast heating Wide adaptive voltage input of 100-240 V 2.8" HD color TFT display with intelligent control Multiple preset groups to switch between different settings quickly Supports F245 and F210 soldering handle types, offering flexibility for different soldering applications Real-time sleep mode to extend the life of the soldering tip Multi-mode real-time monitoring for power and temperature status, enhancing safety and precision Specifications Peak Power 200 W (max) Temperature Range 100°C~450°C (212°F~842°F) Display 2.8" TFT HD Color Screen Heating Time 1 sec Melting Time 3 sec Input Voltage 100-240 V (AC) Input Fuse 3 A Soldering Handle Type F245 Dimensions (Station) 156 x 96 x 103 mm Weight (Station) 475 g Included 1x FNIRSI DWS-200 Soldering Station 1x Soldering Handle F245 6x Soldering Tips (B, KU, K, C2, I, JS) 1x Connecting Cable 2x Helping Hands 1x Power Cable (EU) Downloads Manual Firmware V1.3

Read more less

With this 65 W USB-C PD power supply (with GaN technology) and the included USB-C cable you can start using the FNIRSI HS-01 soldering iron straight away. Of course, you can also use this charger to fast charge your tablets and smartphones via USB-C and USB-A. Included 65 W USB-C PD GaN Power Supply (EU) USB-C cable (1.2 m)

Read more less

The FNIRDSI DSO-TC4 is a multifunctional transistor oscilloscope that is both comprehensive and practical. It is designed for use in maintenance and R&D applications, integrating an oscilloscope, transistor tester, and signal generator into a single device. Features Equipped with a 2.8-inch TFT color screen for a clear and intuitive display Built-in high-capacity rechargeable lithium battery (1500 mAh) with a standby time of up to 4 hours Compact and lightweight, ideal for mobile use Specifications Oscilloscope Analog Bandwidth 10 MHz Real-Time Sampling Rate 48 MSa/s Input Impedance 1 MΩ Coupling Mode AC/DC Test Voltage Range 1:1 Probe: 80 Vpp (+40 V) 10:1 Probe: 800 Vpp (+400 V) Vertical Sensitivity 10 mV/div~10 V/div (X1 range) Vertical Displacement Adjustable with indication Time Base Range 50ns~20s Trigger Mode Auto/Normal/Single Trigger Type Rising edge, Falling edge Trigger Level Adjustable with indication Waveform Freeze Yes (HOLD function) Automatic Measurement Max, Min, Avg, RMS, Vpp, Frequency, Cycle, Duty Cycle Component Tester Transistor Amplification factor "hfe"; Base-Emitter voltage "Ube", Ic/Ie, Collector-Emitter reverse leakage current "Iceo", Ices, Forward voltage drop of protection diode "Uf" Diode Forward voltage drop <5 V (Forward voltage drop, Junction capacitance, Reverse leakage current) Zener Diode 0.01~32 V Reverse Breakdown Voltage (K-A-A Test Area) Field-Effect Transistor (FET) JFET: Gate capacitance "Cg", Drain current Id under "Vgs", Forward voltage drop of protection diode "Uf" IGBT: Drain current Id under Vgs, Forward voltage drop of protection diode Uf MIOSTET: Threshold voltage "Vt", Gate capacitance "Cg", Drain-Source resistance "Rds", Forward voltage drop of protection diode "Uf" Unidirectional SCR Trigger voltage <5V, Gate level (Gate voltage) Bidirectional SCR Trigger current <6mA (Gate voltage) Capacitor 25pF~100mF, Capacitance value, Loss factor "Vloss" Resistor 0.01Ω~50MΩ Inductor 10μH~1000μH, DC resistance DS18B20 Temperature sensor, Pins: GND, DQ, VDD DHT11 Temperature and humidity sensor, Pins: VDD, DATA, GND Signal Generator Output Waveform Supports 13 waveform outputs Waveform Frequency 0-50 KHz Square Wave Duty Cycle 0-100% Waveform Amplitude 0.1-3.0 V General Display 2.8-inch TFT color screen Backlight Brightness adjustable Power Supply USB-C (5 V/1 A） Battery 3.7 V/1500 mAh Languages English, German, Spanish, Portuguese, Russian, Chinese, Japanese, Korean Dimensions 90 x 142 x 27.5 mm Weight 186 g Included 1x FNIRSI DSO-TC4 (3-in-1) Oscilloscope (10 MHz) 1x P6100 Oscilloscope probes (10X) 1x Alligator clip probe 3x Test hooks 1x Adapter 1x USB-C charging cable 1x Manual Downloads Manual Firmware V0.0.3 (+V1.0.9)

Read more less

The FNIRSI 2C53P is a powerful 2-channel oscilloscope with a 50 MHz bandwidth and 250 MS/s sampling rate, ideal for electronics professionals, makers, and students. It offers precise measurements up to ±400 V, a 4.5-digit True RMS multimeter, and an integrated signal generator for versatile applications. With a 4.3-inch color touchscreen and a 4000 mAh battery providing up to 4 hours of use, the FNIRSI 2C53P combines functionality and convenience in one compact device. Specifications General Display 4.3" TFT Color Touch screen (480 x 272) Power Supply USB-C (5 V/2 A) Battery 4000 mAh Lithium battery Languages Chinese, English, Russian, Japanese, Spanish, Portuguese, German, Korean Dimensions 145 x 98 x 35 mm Weight 360 g Oscilloscope Channels 2 Bandwidth 50 Mhz Real-time sampling rate 250 MSa/s Storage Depth Up to 64 kByte Time base range 10 ns/div – 10 s/div Vertical Sensitivity 10 mV/div – 10 V/div Waveform Display Mode YT/XY/scroll Vertical Resolution 8 bits Input Impedance 1 MΩ Bandwidth limit Support 20 MHz limit Probe Attenuation Coefficient 1x/10x Input Coupling AC/DC Trigger Type Rising/Falling edge Peak Voltage ±400 V Trigger Level Range 8 cells (positive/negative) Trigger Mode Auto/Normal/Single Storage Space 13 MB Measured Data Period, frequency, peak-to-peak value, maximum value, minimum value, average value, effective value, amplitude, duty cycle, pulse width Multimeter Function Range Accuracy DC Voltage 1.9999V/19.999V/199.99V/1000.0V ±(0.5%+3) AC Voltage 1.9999V/19.999V/199.99V/750.0V ±(1%+3) DC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.2%+3) AC Current 19.999mA/199.99mA/1.9999A/9.999A ±(1.5%+3) Resistance 19.999MΩ/1.9999MΩ/199.99KΩ/19.999KΩ ±(1.5%+3) 1.9999KΩ/199.99Ω ±(0.5%+3) Capacitance 999.9uF/99.99uF/9.999uF/999.9nF/99.99nF/9.999nF ±(2.0%+5) 9.999mF/99.99mF ±(5.0%+20) Temperature −55~1300°C (−67~2372°F) ±(2.5%+5) Diode/ON-OFF Yes Signal Generator Different Waveform Output Frequencies Sine wave: 10 MHzOther waveforms: 5 MHz Waveform Frequency 0-10 MHz Waveform Amplitude 0.1-3.0 V Square Wave Duty Cycle 0-100% Included 1x FNIRSI 2C53P (3-in-1) 2-ch Oscilloscope 2x P6100 Probes (100 MHz) 1x Multimeter Probe 1x Alligator Clip Probe 1x USB Cable 1x Manual Downloads Manual Firmware V1.8

Read more less

The FNIRSI S1 portable digital multimeter can accurately measure AC/DC voltage, resistance, NCV, diode, continuity, capacitance, temperature, frequency and live wire. It is a really useful tool for solving electrical issues in industry and the home. It is suitable for household sockets, fuses, batteries (including vehicles), troubleshooting automotive circuits, charging systems, testing electronics in cars, etc. Smart Multimeter The multimeter can automatically detect AC/DC voltage, resistance and continuity, which is suitable for both beginners and professionals. Specifications AC voltage 0~1000 V ±(0.8% +3) DC voltage 0~1000 V ±(0.8% +3) Resistance 0~100 MΩ ±(1.2% +3) Capacitance 0 nF~10 mF ±(4.5% +5) Frequency 0 Hz~10 Mhz ±(0.1% +3) Temperature −20~1000°C ±(2% +5) Diode Yes Automatic OFF Yes Lighting Yes On-off buzzer Yes Auto range Yes NCV induced voltage Yes Live mode Yes Data hold Yes Analog Yes Low voltage indication Yes Max range 9999 counts Valid value 50 Hz~1 kHz Material ABS Display VA color screen Power supply via USB-C (1000 mA rechargeable lithium battery) Dimensions 143 x 75 x 19 mm Weight 135 g Included FNIRSI S1 Multimeter Tip table pen Temperature probe USB cable Manual Downloads Manual

Read more less

The LCR-P1 transistor tester is a high-precision, multi-functional electronic tester specifically designed for electronics engineers, technicians and enthusiasts to determine and analyze the performance and characteristics of semiconductor components such as transistors, diodes, triodes and field-effect transistors (FETs). Equipped with a 1.44-inch color screen, it enables multi-parameter measurement of various components, automatically identifies the type and pin arrangement of the tested component, simplifies the operation process and improves test efficiency. Specifications Transistor range 10 < β < 600 Capacitance Range 25 pF-100 mF Inductance range 10 μH-1000 μH Resistance Range 0.01 Ω-50 MΩ Diode Forward voltage drop <4.5 V Voltage Regulator Diode 0.01-4.5 V0.01-32 V Field-Effect Transistor JFET / IGBT / MOSFET Bidirectional Thyristor Turn-on voltage <5 VGate trigger current <6 mA IR Decoding NEC protocol IR code Display 1.44" Color Screen Power Supply 300 mAh lithium battery Battery 0.1-4.5 V Charging USB-C (5 V/1 A) Operating Temperature 0~40°C Dimensions 71 x 87 x 28 mm Included 1x FNIRSI LCR-P1 Transistor Tester 1x Replaceable test board 3x Test hooks 1x USB cable 1x Manual Downloads Manual Firmware V1.0.9

Read more less

The FNIRSI 1013D is a fully featured 2-channel tablet oscilloscope with a high-resolution 7-inch LCD screen (800 x 480 pixels). The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. With full trigger functions (single/normal/automatic), it can be used for periodic analog signals or non-periodic digital signals. The built-in high-voltage protection module can withstand a continuous voltage of up to 400 V. Features Intelligent anti-burn,1X can withstand up to 400 V withstand voltage. 100 MHz analog bandwidth @ 1 GSa/s sampling rate (1X = 5 MHz,10X = 100 MHz). Fully fit 7-inch 800 x 480 resolution color TFT LCD display with bright colors and high contrast. Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation. High measurement voltage range, 1X can measure 0~40 V, 10X can measure 0~400 V,100X can measure 0~4000 V. Up to 12 parameters measurement: VPP, VP, Vmax, Vmin, Vavg, Vrms, Frequent, Duty+, Duty-, Time+, Time−, Period. Cursor measurement function, it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic). At any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO. One-button waveform storage and screenshot. Built-in 1 GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal. Built-in 6000 mAh rechargeable lithium battery, fully charged for 4 hours of continuous use at the highest screen brightness. Memory compression technology, waveform refresh screen does not flicker. Screen brightness adjustment. Background grid brightness adjustment. Applications Electronic DIY Appliance repair Car repair Equipment debug Scientific research Product development Specifications Channels 2 LCD size 7 inch LCD resolution 800 x 480 Display technology TFT Bandwidth 100 Mhz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50S ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X: 40 V, 10X: 400 V Cursor Position XY, Trigger Y Roll mode Yes One button AUTO Yes Waveform storage 1000 pictures + 1000 waveforms Waveform manager Yes Voltage accuracy ±2% Frequency precision ±0.01% high precision Parameter 12 kinds in total Battery 6000 mAh Lithium Standby 4 hours Extension USB export Power supply USB-C, 5 V @ 2 A/3 A/4 A Dimensions 184 x 124 x 50 mm Weight 650 g Included 1x FNIRSI 1013D 2-ch Tablet Oscilloscope 2x 100 MHz Probes (1X and 10X) 1x USB charger 1x USB cable 1x Manual Downloads Manual Firmware

Read more less

This multifunctional metal soldering iron stand (with adjustable angle) is the perfect tool to use together with the FNIRSI HS-01 soldering iron.

Read more less

The FNIRSI DSO152 is an extremely practical and cost-effective handheld oscilloscope with a real-time sampling rate of 2.5 MSa/s, a bandwidth of 200 kHz and complete trigger functions (single, normal and automatic). It can be used for both periodic analog signals and non-periodic digital signals and can measure voltages up to ±400 V. Equipped with an efficient one-key AUTO, it can display the measured waveform without cumbersome adjustments. It is equipped with a high-resolution 2.8-inch LCD screen with a resolution of 320x240 pixels and a built-in 1000 mAh high-quality lithium battery for up to 4 hours of operation. Specifications Sampling rate 2.5 MSa/s Bandwidth 200 kHz Vertical sensitivity 10 mV/DIV - 20 V/DIV (Progress according to the 1-2-5 way) Time base range 10µS/DIV - 50s/DIV (Progress according to the 1-2-5 way) Voltage range X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V) Trigger method Auto/Normal/Single Coupling method AC/DC Display 2.8' (320x240 pixels) USB charging 5 V/1 A Lithium battery capacity 1000 mAh Square wave calibration Frequency: 1K, Duty cycle: 50% Dimensions 99 x 68.3 x 19.5 mm Weight 100 g Included FNIRSI DSO152 oscilloscope Alligator clip probe USB cable Lanyard Manual Downloads Manual Firmware V0.1

Read more less

The FNIRSI GC-02 nuclear radiation detector offers a sleek, portable design with high-precision Geiger-Müller counters for accurate detection of ionizing radiation (γ-rays, X-rays, etc.). Its 1.5-inch HD LCD screen displays real-time, average, max, and cumulative values. Features include alarm settings, customizable sleep/shutdown times, timed monitoring, and history viewing with up to 10 saved records. The 850 mAh rechargeable battery provides up to 6 hours of use. Compact and reliable, the FNIRSI GC-02 is perfect for on-the-go nuclear radiation detection. Features Food and Metal Detection Marble and Ore Inspection Nuclear Industry Radioactivity Detection Radioactive Medical Equipment Testing Multifunctional Real-Time Monitoring Core Technology: Geiger-Müller Counter High-Capacity 850 mAh Battery Detector: Energy Compensation GM Tube (Geiger Counter Tube) Detection Ray Types: Gamma Rays, X-Rays, Beta Rays Specifications Detection Radiation Type Ionizing radiation (γ-rays, X-rays, etc.) Detector Energy compensation GM tube (Geiger counter tube) Dose Current Rate 0.00-1000 μSv/h (1 mSv/h) Cumulative Dose Equivalent 0.00 μSv-500.0 mSv Energy Range 48 keV-15 Mev ≤±30% (for 137Cs -) Sensitivity 80 CPM/uSv (for Co-60) Dosage Unit μSv/h, μGy/h, mR/h, CPS, CPM Battery Capacity 850 mAh Alarm Method Light, Sound Languages Chinese, English, Russian, German, Japanese, Portuguese, Spanish, Korean Dimensions 106.5 x 44.5 x 25 mm Included 1x GC-02 Nuclear Radiation Detector 1x USB cable 1x Lanyard loop Downloads Manual

Read more less

The FNIRSI WD-02 wall detector is an improved version of the previous version WD-01 with a better high-resolution TFT display and a new user interface with additional languages. The 3-stage sensitivity adjustment increases measurement accuracy. It can be used to detect steel bars, metal beams, metal pipes, wood and wires in walls, ceilings and floors. There are 3 detection modes available: metal, wood and AC detection. Features The small size of this tool is very convenient for daily use, you can also easily hold it while using. With this wall detector scanner you can quickly locate edges and center metal, studs, beams, pipes and live AC cables behind walls, floors and ceilings. The measuring range is ≤38 mm for wood, ≤40 mm for AC cables, ≤100 mm for metal pipes and ≤120 mm for reinforcing bars. The HPC detection module provides better anti-interference ability and faster computing speed. The screen displays the target depth, reaches the detection center and material. The indicator light turns yellow or red depending on the target distance and the green light means 'No target'. It also beeps when a target is detected. When the center is reached, warnings are continuously issued. This tool can be widely used for home decoration, wall decoration, home appliance installation, road maintenance, etc. The center positioning hole design allows you to directly mark the drilling position after detection and achieve precise drilling. Specifications Max detection depth Metals 120 mm Non-ferrous metals (copper) 100 mm AC wire 50 mm Single-strand copper wire 40 mm Wooden Precision mode 20 mmDepth mode: 38 mm Automatic ring down After 5 minutes of inactivity Power supply 300 mAh rechargeable lithium battery, USB-C charging Dimensions 138 x 68 x 22 mm Weight 122 g Included FNIRSI WD-02 Wall Detector Scanner USB cable Storage bag Manual Downloads Manual

Read more less

The FNIRSI DPS150 is a high-performance adjustable DC power supply that features a USB-C input interface and multiple power supply modes, allowing precise adjustment of output voltage (0-30 V) and current (0-5 A). It provides efficient, low-consumption, and stable output, equipped with multiple safety protection functions including overvoltage, overcurrent, overload, overheating, and reverse connection. It can be flexibly applied to serial connection of multiple devices, with rich and user-friendly display and operation, compact and portable design, meeting various application needs. Features 30 V, 5 A, 150 W variable DC power with 0.01 V, 0.001 A precision, CC/CV modes, and <20 mV ripple to protect sensitive electronics. Supports PC, QC, and DC inputs with programmable outputs and 6 preset voltage/current settings. Compatible with 4 mm banana plugs, U-shaped terminals, and copper wires for various equipment. 8 safety mechanisms including overvoltage, current, short circuit, and overheating protection. 2.8-inch HD IPS screen with 90° flip, numerical and curve displays for easy monitoring. Small, space-saving design for use in labs, repairs, and DIY projects. Specifications Input Voltage 5~32 V DC Input Current 100 mA-5 A Output Voltage 0-30 V Output Current 0~5 A Output Power 0-150 W Input Way PD fast charger QC fast charger Power bank DC power adapters Operating Environment 0-40°C Load Regulation 0.49% Full Load Efficiency 96.30% Display 2.8 inch (320 x 240) Dimensions 106 x 76 x 28 mm Weight 178 g Included 1x DPS150 Power Supply 2x Alligator clip wires (black & red) 1x C2C PD charging cable 1x 100 W PD GaN Adapter (EU) 1x Micro USB cable 1x Manual Downloads Manual Firmware V0.0.1

Read more less

The FNIRSI DMT-99 is an intelligent digital multimeter with 10000 counts, which offers a high measuring range and high resolution. It can accurately measure AC/DC voltage, AC/DC current, 10 A current and can also be used to test conductivity, capacitance, frequency, duty cycle, resistance, diode, temperature, NCV, live wire detection, etc. It is suitable for various electronic maintenance fields such as mechanical engineering, laboratories, automobiles and home appliances. It is equipped with a 1500 mAh lithium battery and a 2.4' TFT full-color display with a resolution of 240 x 320 pixels. Specifications Function Range Accuracy DC voltage 9.999 V/99.99 V/999.9 V ±(0.5%+3) AC voltage 9.999 V/99.99 V/750.0 V ±(1%+3) DC current 9999 uA/99.99 mA/999.9 mA/9.999 A ±(1.2%+3) AC current 9999 uA/99.99 mA/999.9 mA/9.999 A ±(1.5%+3) Resistance 9.999 MΩ/999.9 KΩ/99.99 KΩ/9.999 KΩ/999.9 Ω ±(1.5%+3) 99.99 MΩ ±(1.5%+3) Capacitance 999.9 µF/99.99 µF/9.999 µF/999.9 nF/99.99 nF/9.999 nF ±(2.0%+3) 9.999 mF/99.99 mF ±(5.0%+3) Frequency 9.999 MHz/999.9 KHz/9999 KHz/9.999 KHz/999.99 Hz/99.99 Hz/9.999 Hz ±(0.1%+3) Temperature -55~1300°C (-64~2372°F) ±(2.5%+3) Diode Yes Continuity test Yes NVC Yes Live wire detection Yes Max counts 10000 counts Battery capacity 1500 mAh Dimensions 155 x 80 x 36 mm Weight 191 g Included 1x FNIRSI DMT-99 Multimeter 2x Test pens 1x USB-C charging cable 1x Manual Downloads Manual Firmware V2.4

Read more less

The FNIRSI NVS-40 is a night vision binocular designed for observing objects in pitch-black or low-light environments. It offers unlimited observation distance in weak light conditions and can reach up to 300 meters in complete darkness. The device is equipped with a USB interface and a TF card slot, enabling firmware updates and storage for photos and videos. Fully functional, it features a color screen that can be used during both day and night. Key functionalities include photo capturing, video recording, playback, and electronic zoom of up to 6x. This device serves as the ultimate auxiliary tool for extending human night vision capabilities. Specifications Drawtube Binocular Electronic Zoom 6x Magnification 500x & under Objective Lens Diameter 25 mm Low Light or Daytime Observation Distance 2 m~∞ Full Black Observation Distance 300 m (max) Video Resolution 4K (3840x2160) / 2K (2560x1440) / 1080FHD (1920x1080) / 720P (1280x720) / VGA (640x480) / QVGA (320x240) Photo Resolution 36MP / 32MP / 30MP / 24MP / 20MP / 16MP / 12MP / 10MP / 8MP / 5MP / 3MP / VGA IR Wavelength 850 nm Water Resistance Level IPX6 White Balance Automatic, Daylight, Cloudy, Tungsten Filament, Fluorescent ISO Auto, 100, 200, 400, 800 LCD Brightness Adjustment High, medium, and low levels Light Source Frequency 50 Hz/60 Hz Storage 32 GB TF memory card Voltage 3.7 V Power Supply 18650 internal battery Charging USB-C (5 V/1 A) Display 3.0" HD IPS Color Screen Temperature −5~40°C Humidity 0-80% Languages Chinese / Traditional / English / Japanese / Italian / French / German / Russian / Spanish / Portuguese Dimensions 136 x 153 x 56 mm Weight 265 g Included 1x NVS-40 Night Vision Binocular 1x 18650 Lithium battery 1x TF memory card (32 GB) 1x USB cable 1x Storage bag 1x Manual Downloads Manual

Read more less

The FNIRSI HS-02A is an improved version of the HS-01 soldering iron with a better grip and a shorter tip for more comfort and precision during use. It features a larger 0.96-inch IPS HD color display that allows for better visibility of settings and status. With an output power of 100 W, the HS-02A heats up quickly and reaches operating temperature in about 2 seconds. The temperature is adjustable in a range of 100-450°C (212-842°F) to meet different soldering requirements. Features Temperature: 100-450°C (212-842°F) Accurate temperature adjusting and control Fast heating CNC Metal Shell Adaptive Power 100 W High Power Protocols: PD, QC Specifications Temperature Range 100-450°C (212-842°F) Working Voltage 9-20 V Display 0.96" IPS HD Color Screen Power Supply USB-C Fast Charging Protocols PD / QC Power 100 W (max) Dimensions 180 x 20 mm Weight 61 g Included 1x FNRISI HS-02A Smart soldering iron 6x Soldering iron tips (HS02A-KU, HS02A-K, HS02A-JS, HS02A-I, HS02A-C2, HS02A-B) 1x 100 W USB-C power supply (EU) 1x DC to USB-C power cable 1x USC-C charging cable 1x Mini soldering iron stand 1x Manual Downloads Manual Firmware V1.7

Read more less