Oscilloscopes

51 products


  • OWON HDS2102s 2-ch Oscilloscope (100 Mhz) + Multimeter + Signal Generator

    OWON OWON HDS2102s 2-ch Oscilloscope (100 Mhz) + Multimeter + Signal Generator

    The OWON HDS2102s is a portable 3-in-1 multifunctional tester, which can be used as a 2-ch oscilloscope with a bandwidth of 100 MHz, multimeter and signal generator. It features a high-contrast 3.5-inch color display suitable for outdoor facility maintenance, rapid on-site measurement, automobile maintenance, power detection. etc.Features Oscilloscope + multimeter + waveform generator, multifunction in one 3.5-inch high-resolution, high-contrast color LCD display, suitable for outdoor use 18650 lithium battery, can work continuously for 3-6 hours USB Type-C interface, support power bank, support PC software connection Self-calibration function SCPI supported, facilitate secondary development Specifications Bandwidth 100 MHz Channels 2-ch Oscilloscope + 1-ch Generator Sample Rate 500 MSa/s Acquisition Model Normal, Peak detect Record Length 8K Display 3.5-inch LCD Waveform Refresh Rate 10,000 wfrms/s Input Coupling DC, AC, and Ground Input Impedance 1 MΩ ±2%, in parallel with 16pF ±10pF Probe Attenuation Factors 1X,10X,100X,1000X,10000X Max. input Voltage 400 V (DC+AC, PK-PK, 1MΩ input impedance) (10:1 probe attenuation) Bandwidth Limit (typical) 20 MHz Horizontal Scale 2ns/div - 1000s/div, step by 1 - 2 - 5 Vertical Sensitivity 10mV/div - 10V/div Vertical Resolution 8 bits Trigger Type Edge Trigger Modes Auto, Normal, single Automatic Measurement Frequency, Period, Amplitude, Max, Min, Mean, PK-PK Cursor Measurement ΔV, ΔT, ΔT&ΔV between cursors Communication Interface USB Type-C Multimeter Specifications Max. Resolution 20,000 counts Testing Mode Voltage, Current, Resistance, Capacitance, Diode, and Continuity test Input Impedance 10 MΩ Max Input Voltage AC 750 V, DC 1000 V Max Input Current DC: 10 A, AC: 10 A Diode 0-2 V Waveform Generator Specifications Frequency Output Sine 0.1 Hz - 25 MHz Square 0.1 Hz - 5MHz Ramp 0.1 Hz - 1 MHz Pulse 0.1 Hz - 5 MHz Arbitrary 0.1 Hz - 5 MHz Sampling Rate 125 MSa/s Channel 1-ch Amplitude Range (high impedance) 20 mVpp - 5 Vpp Waveform Length 8K Vertical Resolution 14 bits Output Impedance 50Ω Included 1x OWON HDS2102s 1x Power adapter 1x USB cable 1x Passive probes 2x Crocodile clip cable 1x Set of multimeter probes (one red and one black) 1x User manual 1x Probe correction adjustment knife Downloads User Manual Specifications SCPI Protocol Quick Guide Software

    € 249,00

    Members € 224,10

  • OWON SDS1104 4-ch Oscilloscope (100 MHz)

    OWON OWON SDS1104 4-ch Oscilloscope (100 MHz)

    Out of stock

    Bandwidth 100MHz Sample Rate 100MS/s Horizontal Scale (s/div) 5ns/div - 1000s/div, step by 1 - 2 - 5 Channel 4 Display 7' color LCD, 800 x 480 pixels Input Coupling DC, AC and GND Vertical Resolution (A/D) Vertical Resolution (A/D) Vertical Sensitivity 5mV/div - 5V/div (at input) Trigger Type Edge, Video Trigger Mode Auto, Normal and Single Waveform Math +, -, x, ÷, invert, FFT Fuse 2A, T class, 250 V Dimension (W x H x D) 301 mm x 152 mm x 70 mm Weight 1.1 kg Included 1 x SDS1104 1 x Mains power cord 1 x CD Rom 1 x Quickstart Guide 1 x USB Cable 4 x Oscilloscope probe 1 x Probe Adjust For more information, check out the user manual here.

    Out of stock

    € 299,00

    Members € 269,10

  • OWON XDS2102A 2-ch Oscilloscope (100 MHz)

    OWON OWON XDS2102A 2-ch Oscilloscope (100 MHz)

    1 review

    12-bit high-resolution ADC, restoring the waveform detail fully 20M record length, and 55,000 wfms/s waveform refresh rate low background noise, vertical sensitivity in 1 mV/div - 10 V/div multi-trigger, and bus decoding function SCPI and LabVIEW supported ultra-thin body-design, less space accommodation multi-interface integration 8 inch 800 x 600 high-resolution LCD XDS2102A Bandwidth 100MHz Sample Rate 1GS/s Vertical Resolution (A/D) 12 bits Record length 20M Horizontal Scale (s/div) 2ns/div - 1000s/div, step by 1 - 2 - 5 Channel 2 + 1 (external) Display 8' color LCD, 800 x 600 pixels Trigger Type Edge, Video, Pulse, Slope, Runt, Windows, Timeout, Nth Edge, Logic, I2C, SPI, RS232, and CAN (standard for XDS2102A/optional for other models) Bus Decoding I2C, SPI, RS232, and CAN Communication Interface USB host, USB device, USB port for PictBridge, Trig Out (P/F), LAN, and VGA (optional) Power Supply 100V - 240V AC, 50/60Hz, CAT II Fuse 2A, T class, 250V Dimension (W x H x D) 340 mm x 177 mm x 90 mm Weight 2.60 kg

    € 469,00

    Members € 422,10

  • OWON VDS6102A 2-ch USB Oscilloscope (100 MHz)

    OWON OWON VDS6102A 2-ch USB Oscilloscope (100 MHz)

    Features Bandwidth 100 MHz Vertical resolution 14 bits Rise time ≤3.5 ns Memory 10 Mpts Number of channels 2 channels + 1 channel function generator Horizontal scale 5ns - 100s/div Sample rate Max. 1 GSa/s Maximum voltage 40 V (peak - peak) Automatic measurements Vpp, Vavg, Vamp, Vrms, Freq, Period, Vmax, Vmin, Vtop, Vbase, Overshoot, Preshoot, Rise Time, Connectivity USB (type C), LAN, Wifi (optional) Fall Time, Delay A→B↑, Delay A→B↓, +Width, -Width, +Duty, -Duty Bandwidth 5 MHz Dimensions 190 x 120 x 18mm Weight ~380 g Sample rate 25 MSa/s Standard waveforms Sine (0.1 Hz - 5 MHz), Square (0.1 Hz - 200 kHz), Ramp (1 Hz - 10 kHz), Pulse (1 Hz - 10 kHz) Resolution 10 bits DC offset range (AC + DC) ±2.5 V Amplitude range 10 mVpp - 5 Vpp

    € 329,00

    Members € 296,10

  • Miniware DS212 2-ch Mini Oscilloscope (1 MHz)

    Miniware Miniware DS212 2-ch Mini Oscilloscope (1 MHz)

    Features Synchronous mode: Auto, Normal, Single, None, Scan Rising/Falling edge trigger Modes of vertical precise, horizontal precise measurement and triggering threshold Auto Measurement: frequency, cycle time, duty cycle, DC RMS voltage/Vpp /Vmax/Vmin/Vavg Inbuilt signal generator/10 Hz-1 MHz square wave (duty adjustable) or 10 Hz-20 KHz Sine/Square/Triangle/Sawtooth wave Specifications Analog bandwidth 1 MHz Max sample rate 10 Msa/s Max sample memory depth 8K Analog input impedance 1 MΩ Max input voltage ±40 V (X1) Coupling AC/DC Vertical sensitivity 20 mv/Div~10 V/Div (1-2-5) Horizontal sensitivity 1 uS/Div~2 S/Div (1-2-5) Storage Built-in 8 MB U disk storage for waveform data and images Power supply Internal 550 mAh Lithium battery, recharging through Micro USB port Display 2.8' Full Color TFT LCD (320x240 pixels) Dimensions 100 x 56.5 x 10.7 mm Downloads User Manual Source Code App

    € 149,95

    Members € 134,96

  • Last stock! Velleman EDU08 Educational LCD Oscilloscope

    Velleman Velleman EDU08 Educational LCD Oscilloscope

    2 in stock

    Specifications High contrast LCD: 64 x 128 pixels with white LED backlight Maximum sample rate: 1MS/s for repetitive signals, 100kS/s in real time Input amplifier bandwidth: 200kHz (-3 dB) Measurements can be performed up to: 100kHz Input impedance: 100kohm // 20pF Maximum input voltage: 30Vpeak (AC + DC) Input coupling: DC and AC AD resolution: 8 bits Run modes: run, single Trigger level adjustable: in 16 steps Timebase range: in 15 steps, 10µs/division to 500ms/division Input sensitivity range: in 6 steps, 100mV/division to 5V/division Test output: 1.95kHz / 3.3Vpp Full auto set up for: Volt/div and time/div (or manual) Sensitivity down to 10mV Readouts: DC, AC+DC, true RMS, dBm, Vpp, min. & max. Time and voltage markers readout Frequency readout (through markers) Battery operated: 4 x AAA batteries (max. 100mA) Power save mode Dimensions: 80 x 115 x 40 mm (3.14 x 4.52 x 1.57') Weight: 190g (6.70 oz) with batteries

    2 in stock

    € 59,95

    Members € 53,96

  • OWON XDS3104E 4-ch Oscilloscope (100 MHz)

    OWON OWON XDS3104E 4-ch Oscilloscope (100 MHz)

    Out of stock

    Features Function button area DAQ, P/F, W. R E C Trigger control area Horizontal control area Vertical control area Default Print Turn on/off the Counter Snapshot Direction key Multipurpose knob Specifications XDS3104E Bandwidth 100MHz Sample Rate 1 GS/s Vertical Resolution (A/D)) 8 bits Record length 40M Waveform Refresh Rate 45,000 wfms/s Horizontal Scale (s/div)) 2 ns/div - 1000s/div, step by 1 - 2 - 5 Channel 4 Display 8' color LCD, 800 x 600 pixels display Sample Rate / Relay Time Accuracy ±2.5 ppm Input Coupling DC, AC, GND Vertical Sensitivity 1 mV/div - 10 V/div (at input) Trigger Type Edge, Video, Pulse, Slope, Runt, Windows, Timeout, Nth Edge and Logic Trigger Mode Auto, Normal, and Single Vertical Range ±2 V (1 mV/div~50 mV/div)±20 V (10 0mV/div~1 V/div)±200 V (2 V/div~10 V/div) Waveform Math +, -, *, /, FFT, Intg, Diff, Sqrt, and user-defined function Communication Interface USB host, USB device, USB port for PictBridge, Trig Out (P/F), LAN, and VGA (optional) Frequency Counter available Power Supply 100 V - 240 V AC, 50/60 Hz, CAT II Fuse 2 A, T class, 250 V Dimensions 340 x 177 x 90 mm Downloads User manual Quick guide USB Driver

    Out of stock

    € 499,00

    Members € 449,10

  • PeakTech 1404 2-ch Oscilloscope (100 MHz)

    PeakTech PeakTech 1404 2-ch Oscilloscope (100 MHz)

    Specially developed for the education and hobby sector, this fully-fledged digital storage oscilloscope offers the best possible price/performance ratio without having to compromise on functionality or technical features. Whether Autoset and Autoscale, mathematical measurement functions, FFT, Cursor or XY mode and even a zoom function, all standard market functions are already integrated in this series. The data storage of the waveforms is either internal with memory for 16 waveforms or external on a USB memory in TXT, CSV or BIN format, which can be read out with the included software. Configurations can also be saved internally or screenshots of the display can be saved externally. The display of the waveforms can be achieved quickly and user-friendly through the Autoset function, via AutoScale the measured waveforms can be displayed even more precisely as required, whereby these settings can of course also be carried out completely manually via the key control. Features 2-channel oscilloscope with 100 MHz analogue bandwidth at max. 1 GS/s sampling rate 17.5 cm (7') TFT colour display with 800 x 480 pixels USB device connection for real-time data transmission USB host connection for external USB data carriers Handy and flat housing design with carrying handle Autoset function for user-friendly operation Recording length of max. 10,000 points Automatic measuring modes, XY mode and FFT function Specifications Bandwidth 100 MHz Channels 2 Sampling 1 CH 1 GS/s Sampling 2 CH 500 MS/s Rise Time < 3.5 ns Display Type Color TFT Resolution 800 x 480 Pixels Screen size (TFT) 17.5 cm (7') Hor. scale max. 1000 s/div Hor. scale min. 2 ns/div Memory depth 10,000 Points Vert. resolution 8 Bit Vert. scale max. 5 V/div Vert. scale min. 2 mV/div Mains voltage 110/240 V AC; 50/60 Hz Downloads User Manual Driver Software

    € 299,00

    Members € 269,10

  • OWON XDS3102A 2-ch Oscilloscope (100 MHz)

    OWON OWON XDS3102A 2-ch Oscilloscope (100 MHz)

    1 review

    The OWON XDS3102A is a 12-bit 2-channel digital storage oscilloscope (100 MHz) with digital multimeter and 2-channel arbitrary waveform generator (25 MHz). It features a touchscreen, a VGA output, WiFi and a 13200 mA battery. Performance 8-bit, 12-bit or 14-bit high-resolution ADC, restoring the waveform detail fully 40M record length, max 75,000 wfms/s waveform refresh rate Ow background noise, vertical sensitivity in 1 mV/div - 10 V/div Multi-trigger, and bus decoding function SCPI and LabVIEW supported Features Ultra-thin body-design, less space accommodation Multi-interface integration – USB host, USB device, USB port for PictBridge, LAN, AUX, and more VGA port – a better solution for video expansion, and teaching demonstration 8 inch 800 x 600 high-resolution LCD Optional multi-point touch screen, more user-friendly operation experience Specifications Bandwidth 100 MHz Sample Rate 1 GS/s Vertical Resolution (A/D) 12 bits Record length 40M Horizontal Scale (s/div) 2 ns/div - 1000s/div, step by 1 - 2 - 5 Channel 2 + 1 (external) Display 8" color LCD, 800 x 600 pixels Waveform Math   +, -, ×, ÷, FFT, FFTrms, Intg, Diff, Sqrt, User Defined Function, digital filter (low pass, high pass, band pass, band reject) Trigger Type Edge, Video, Pulse, Slope, Runt, Windows, Timeout, Nth Edge, Logic, I²C, SPI, RS232 Bus Decoding I²C, SPI, RS232 Communication Interface USB host, USB device, USB port for PictBridge, Trig Out (P/F), LAN Power Supply 100-240 V AC, 50/60 Hz, CAT II Power Consumption <15 W Fuse 2A, T class, 250 V Dimension 340 x 177 x 90 mm Weight 2.6 kg

    € 669,00

    Members € 602,10

  • OWON SDS1202 2-ch Oscilloscope (200 MHz)

    OWON OWON SDS1202 2-ch Oscilloscope (200 MHz)

    The OWON SDS1202 2-channel oscilloscope features a high 200 MHz bandwidth, a sample rate of 1 GSa/s, an ultra-thin body and a 7-inch high resolution color LCD. The scope supports SCPI and LabVIEW. Features Bandwidth: 200 MHz 2 channels Sample rate: 1 GS/s Ultra-thin body 7-inch high resolution LCD SCPI and LabVIEW supported Specifications Bandwidth 200 MHz Sample Rate 1 GS/s Horizontal Scale (s/div) 2 ns/div - 1000 s/div, step by 1 - 2 - 5 Channel 2 Display 7' color LCD, 800 x 480 pixels Input Coupling DC, AC and GND Vertical Resolution (A/D) 8 bits (2 channels simultaneously) Vertical Sensitivity 5 mV/div - 5 V/div (at input) Trigger Type Edge, Video Trigger Mode Auto, Normal, and Single Waveform Math +, -, x, ÷, invert, FFT Fuse 2A, T class, 250V Dimension (W x H x D) 301 x 152 x 70 mm Device Weight 1.10 kg Included 1x OWON SDS1202 Oscilloscope 1x Probe 1x Probe adjust 1x Power cord 1x USB cable 1x CD-ROM 1x Quick guide Downloads Datasheet User manual PC software SCPI commands

    € 319,00

    Members € 287,10

  • OWON XDS3064E 4-ch Oscilloscope (60 MHz)

    OWON OWON XDS3064E 4-ch Oscilloscope (60 MHz)

    Out of stock

    Function button area DAQ, P/F, W. R E C Trigger control area Horizontal control area Vertical control area Default Print Turn on/offthe Counter Snapshot Direction key Multipurpose knob XDS3064E Bandwidth 60MHz Sample Rate 1 GS/s Vertical Resolution (A/D)) 8 bits Record length 40M Waveform Refresh Rate 45,000 wfms/s Horizontal Scale (s/div)) 2ns/div - 1000s/div, step by 1 - 2 - 5 Channel 4 Display 8' color LCD, 800 x 600 pixels display Sample Rate / Relay Time Accuracy ±2.5 ppm Input Coupling DC, AC, GND Vertical Sensitivity 1mV/div - 10V/div (at input) Trigger Type Edge, Video, Pulse, Slope, Runt, Windows, Timeout, Nth Edge and Logic Trigger Mode Auto, Normal, and Single Vertical Range ±2V(1mV/div~50mV/div);±20V(100mV/div~1V/div);±200V(2V/div~10V/div) Waveform Math +, -, *, /, FFT, Intg, Diff, Sqrt, and user-defined function Communication Interface USB host, USB device, USB port for PictBridge, Trig Out (P/F), LAN, and VGA (optional) Frequency Counter available Power Supply 100 V - 240 V AC, 50/60 Hz, CAT II Fuse 2A, T class, 250 V Dimensions 340 x 177 x 90 mm Click here for the USB Driver, the user manual or the quick guide provided by OWON.

    Out of stock

    € 399,00

    Members € 359,10

  • Last stock! Miniware DS213 4-kanaals Mini Oscilloscoop (15 MHz)

    Miniware Miniware DS213 4-ch Mini Oscilloscope (15 MHz)

    1 in stock

    The DS213 is a '5-track, 4-wave-line' oscilloscope with digital storage for general electrotechnical tasks and is based on an ARM Cortex-M3 core. The DS213 uses an FPGA to control the external A/D Converter and manage the data cache. It provides 4 partitions for applications to load and upgrade up to 4 different firmware versions. It also has a built-in 8 MB USB flash drive for storing waveforms and upgrading the firmware. The application layer of the oscilloscope code is open source, and users can develop firmware for the oscilloscope according to their own needs. Features Mini size, light weight, portable and handheld. It can store waveforms, making waveform analysis clearer and more effective. Multiple trigger modes, support Ascend/Descend Edge Trigger, Positive/Negative Pulse Trigger, and Logic Trigger. Powerful ability to process waveforms, it can automatically measure parameters such us voltage, frequency and pulse width. Specifications Analoge bandwidth 15 MHz Sampling rate 100 MSa/s CPU ARM Cortex-M3 FIFI & control FPGA ADC HWD9288-100 Analog channels 2 ([CH_A] [CH_B] Digital channels 2 ([CH_C] [CH_D] Analog input impedance 1 MΩ Max input voltage ±40 V (X1 probe)±400 V (X10 probe) Coupling AC/DC Vertical sensitivity 10 mv/Div~10 V/Div (1-2-5 steps) Horizontal sensitivity 100 nS/Div~1 S/Div (1-2-5 steps) Vertical resolution 8 bits Standaard digital channel input impedance 100 KΩ Max digital channel input voltage +5 V Trigger types Ascend/Descend Edge Trigger Mode, Positive/Negative Pulse Trigger, Logic Trigger Trigger modes Auto, Normal, Single, Slow Trigger source [CH_A] [CH_B] [CH_C] [CH_D] Storage Built-in 8 MB U disk storage for waveform data and images Power supply Internal 1000 mAh Lithium battery, external Micro USB port Display 2.8' Full Color TFT LCD (240x400 pixels) Dimensions 99.5 x 59 x 13.5 mm Weight 129 g (with battery) Included 1x DS213 Mini Oscilloscope 2x Probes 1x Date line 1x Allen key 1x USB cable 1x User manual Downloads Manual App Schematics

    1 in stock

    € 249,00

    Members € 224,10

  • OWON HDS1021M-N 1-ch Oscilloscope (20 MHz) + Multimeter

    OWON OWON HDS1021M-N 1-ch Oscilloscope (20 MHz) + Multimeter

    1 review

    Out of stock

    Features 2 in 1 (DSO + Multimeter) Auto-scale function 20 automatic measurements Bandwidth: 20 MHz USB data transmission supported Waveform record and replay Multimeter newly supported SCPI Rechargeable Li-ion battery (6 hours' backup) 2-in-one measurement device Oscilloscope + 3 3/4 digits multimeter + FFT spectrum analyzer. Auto-scale function While in auto-scale status, the oscilloscope will switch to the specific trigger mode, vertical scale, and timebase scale according to the type, amplitude, and frequency of input signal. Adjustable trigger sensitivity Thanks to adjustable trigger sensitivity, this device filters the overlay noise and triggers the signal stably under the circumstance of noise. Specifications Bandwidth 20 MHz Sample Rate (real-time ) 500 MS/s Horizontal Scale (s/div) 5 ns/div~100 s/div, step by 1~2.5~5 Display 3.7” color TFT display (640 × 480 pixels) Channel single Record Length 24K points Vertical Sensitivity 5 mV/div~5 V/div (at input) Vertical Resolution (A/D) 8 bits Trigger Type Edge and Video Trigger Mode Auto, Normal, and Single Trigger Level ±6 divisions from screen center Acquisition Mode Sample, Peak Detect, and Average Waveform Storage 4 waveforms Communication Interface mini-USB, mini-RS232 Power Supply 100 V-240 V AC, 50/60 Hz Li-ion Battery 7.4 V, 6 hours’ operation Dimensions (W × H × D) 115 × 180 × 40 (mm) Multimeter Specifications Full-Scale Reading 3 (3/4) digits (max 4000-count) diode 0 V - 1.5 V Input Impedance 10 MΩ On / Off Test < 50 (± 30) beeping Voltage VDC : 400 mV, 4 V, 40 V, 400 V, 1000 V : ±(1% ± 1 digit);max input: DC 1000 V VAC : 4 V, 40 V, 400 V : ±(1% ± 3 digits), 750 V : ±(2% ± 3 digits);Frequency : 40 Hz - 400 Hz; max input : AC 750 V (virtual value) Current DC : 40 mA, 400 mA : ±(1.5% ± 1 digit), 10 A : ±(3% ± 3 digits) AC : 40 mA : ±(1.5% ± 3 digits), 400 mA : ±(2% ± 1 digit), 10 A : ±(5% ± 3 digits) Impedance 400 Ω : ±(1% ± 3 digits), 40 ΚΩ 4 ΜΩ : ±(1% ± 1 digit), 40 MΩ : ±(1.5% ± 3 digits) Capacitance 51.2 nF - 100 µF : ±(3% ± 3 digits) Software PC software for DSO

    Out of stock

    € 239,00

    Members € 215,10

  • OWON HDS2202s 2-ch Oscilloscope (200 MHz) + Multimeter + Signal Generator

    OWON OWON HDS2202s 2-ch Oscilloscope (200 MHz) + Multimeter + Signal Generator

    The OWON HDS2202s is a portable 3-in-1 multifunctional tester, which can be used as a 2-ch oscilloscope with a bandwidth of 200 MHz, multimeter and signal generator. It features a high-contrast 3.5-inch color display suitable for outdoor facility maintenance, rapid on-site measurement, automobile maintenance, power detection. etc. Features Oscilloscope + multimeter + waveform generator, multifunction in one 3.5-inch high-resolution, high-contrast color LCD display, suitable for outdoor use 18650 lithium battery, can work continuously for 3-6 hours USB Type-C interface, support power bank, support PC software connection Self-calibration function SCPI supported, facilitate secondary development Specifications Bandwidth 200 MHz Channels 2-ch Oscilloscope + 1-ch Generator Sample Rate 1 GSa/s Acquisition Model Normal, Peak detect Record Length 8K Display 3.5-inch LCD Waveform Refresh Rate 10,000 wfrms/s Input Coupling DC, AC, and Ground Input Impedance 1 MΩ ±2%, in parallel with 16pF ±10pF Probe Attenuation Factors 1X,10X,100X,1000X,10000X Max. input Voltage 400 V (DC+AC, PK-PK, 1MΩ input impedance) (10:1 probe attenuation) Bandwidth Limit (typical) 20 MHz Horizontal Scale 2ns/div - 1000s/div, step by 1 - 2 - 5 Vertical Sensitivity 10mV/div - 10V/div Vertical Resolution 8 bits Trigger Type Edge Trigger Modes Auto, Normal, single Automatic Measurement Frequency, Period, Amplitude, Max, Min, Mean, PK-PK Cursor Measurement ΔV, ΔT, ΔT&ΔV between cursors Communication Interface USB Type-C Multimeter Specifications Max. Resolution 20,000 counts Testing Mode Voltage, Current, Resistance, Capacitance, Diode, and Continuity test Input Impedance 10 MΩ Max Input Voltage AC 750 V, DC 1000 V Max Input Current DC: 10 A, AC: 10 A Diode 0-2 V Waveform Generator Specifications Frequency Output Sine 0.1 Hz - 25 MHz Square 0.1 Hz - 5MHz Ramp 0.1 Hz - 1 MHz Pulse 0.1 Hz - 5 MHz Arbitrary 0.1 Hz - 5 MHz Sampling Rate 125 MSa/s Channel 1-ch Amplitude Range (high impedance) 20 mVpp - 5 Vpp Waveform Length 8K Vertical Resolution 14 bits Output Impedance 50Ω Included 1x OWON HDS2202s 1x Power adapter 1x USB cable 1x Passive probes 2x Crocodile clip cable 1x Set of multimeter probes (one red and one black) 1x User manual 1x Probe correction adjustment knife Downloads User Manual Specifications SCPI Protocol Quick Guide Software

    € 299,00

    Members € 269,10

  • Last stock! Siglent SDS1204X-E 4-ch Oscilloscope (200 MHz)

    Siglent Siglent SDS1204X-E 4-ch Oscilloscope (200 MHz)

    1 in stock

    The Siglent SDS1204X-E is a powerful 200 MHz four-channel oscilloscope that is built on the same platform as the very popular SDS1202X-E but with several significant improvements, including two 1 GSa/s ADCs and two 14 Mpt memory modules. Waveform capture rates are up to 100,000 wfms/s in normal mode and 400,000 wfms/s in sequence mode. The SDS1000X-E scopes feature a large 7” 256-level color display with intensity grading and color temperature features.Specifications Model SDS1204X-E Bandwidth 200 MHz Sampling Rate (Max.) 1 GSa/s Channels 2CH+EXT4CH Memory Depth (Max.) 7 Mpts/CH (not interleave mode); 14 Mpts/CH (interleave mode) Waveform Capture Rate (Max.) 100,000 wfms/s (normal mode), 400,000 wfms/s (sequence mode) Trigger Types Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video Serial Trigger (Standard) I2C, SPI, UART/RS232, CAN, LIN Decode Type (Standard) I2C, SPI, UART/RS232, CAN, LIN 16 Digital Channels (four channel series only, option) Maximum waveform capture rate up to 1 GSa/s, Record length up to 14 Mpts/CH USB AWG module (four channel series only, option) One channel, 25 MHz, sample rate of 125 MHz, wave length of 16 kpts Bode plot ( four channel series only) Minimum start frequency of 10 Hz, minimum scan bandwith of 500 Hz, maximum scan bandwidth of 120 MHz (dependent on Oscilloscope and AWG bandwidth), 500 maximum scan frequency points USB WIFI adapter (four channel series only, option) 802.11b/g/b, WPA-PSK, the adapter must be supplied by Siglent to ensure proper functioning

    1 in stock

    € 929,00

    Members € 836,10

  • JYE Tech DSO138 Oscilloscope DIY Kit

    JYE Tech JYE Tech DSO138 Oscilloscope DIY Kit

    1 review

    Out of stock

    DSO138 was designed as a training oscilloscope kit. It contains only the basical oscilloscope functions with no fancy features. Simplicity in structure and easiness in assembly/operation are among the main targets of the design. For these purpose DSO138 uses mostly through-hole parts. The heart of DSO138 is a Cortex-M3 ARM processor (STM32F103C8) from ST. Its 2.4-inch TFT LCD (320 x 240 dotmatrix, 262K colors) displays nice and clear waveforms. Detailed assembly instructions are provided in combination with troubleshooting guide and schematc. Source codes are also available to allow user to add their own features. DSO138 is partially open-sourced. This opens the possibility for users to add different features or develop new applications on the hardware. Features of DSO138: Analog bandwidth: 0 - 200 kHz Sampling rate: 1 Msps max Sensitivity: 10 mV/Div - 5 V/Div Sensitivity error: < 5% Vertical resolution: 12-bit Timebase: 10 µs/Div - 500 s/Div Record length: 1024 points Built-in 1 kHz/3.3 V test signal Waveform frozen (HOLD) function available Save/recall waveform

    Out of stock

    € 44,95

    Members € 40,46

  • Micsig STO1152C Plus 2-ch Oscilloscope (150 MHz)

    Micsig Micsig STO1152C Plus 2-ch Oscilloscope (150 MHz)

    1 review

    Out of stock

    Specifications Bandwidth 150 MHz Analog channels 2 Sample rate 1 GSa/S (single channel) Rise time ≤ 2.3 ns Memory depth 28 Mpts (single channel) Max capture rate 130,000 wfm/s Bandwidth limitation 20MHz, high pass, low pass I/O Port Wi-Fi, LAN, HDMI, USB Host, USB Device, DC Power, Aux out APP Support Android / iOS Built-in storage capacity 8 GB Display 8' Industry TFT LCD touchable capacitive screen, resolution: 800 x 600 pixels, 14 x 10 grids Dimension 280 mm x 180 mm x 50 mm Trigger type Edge, Pulse Width, Logic, Video, Runt, Time Out , N Edge, Slope Automatic Measurements Period, Frequency, Rise Time, Fall Time, Delay, Positive duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Positive Overshoot, Negative Overshoot, Phase, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS. Weight Oscilloscope body 1425 g, battery 320 g

    Out of stock

    € 599,00

    Members € 539,10

  • Last stock! PeakTech 1341 4-ch Oscilloscope (100 MHz)

    PeakTech PeakTech 1341 4-ch Oscilloscope (100 MHz)

    1 in stock

    4-channel digital storage oscilloscope of the latest generation with high-resolution TFT color display and comprehensive additional functions. This series offers a wide range of applications with ease of use in electrical engineering, industry, research and development.Features High-resolution TFT color display with 800 x 600 pixels 20 cm (8“) TFT color display LAN & USB port for real time data transmission Saving of measured values and graphics directly onto the USB-stick Handy and flat case design with carrying handle Autoset function for easy operation Record lenght of max. 40 Mio. points Automatic measurement modes and FFT function Safety: EN 61010-1; CAT II Accessories: USB cable, software CD for Windows, power cable, 2 probes, carrying case and manual Technical Specifications Bandwidth 100 MHz Display 20 cm (8') color-TFT Resolution 800 x 600 Pixel Channel 4 CH Specifications Sampling rate (1/2/4 CH) 1 GS/s; 500 MS/s; 250 MS/s Waveform refresh rate 45.000 wfms/s Rise Time ≤ 3.5 ns Vertical sensitivity 1 mV - 10 V/div. Vertical resolution 8 Bits Horizontal scale 2 ns – 1000s/div. Trigger type Edge/Video/Pulse/Slope Trigger mode Auto, Normal, Single General Record length 40.000.000 points Interfaces LAN, USB Device, USB Host Battery (optional) Model 'AKKU 6' Dimensions (WxHxD) 340 x 175 x 90 mm Weight ca. 2.5 kg

    1 in stock

    € 849,00

    Members € 764,10

  • Last stock! PeakTech 1240 2-ch Oscilloscope (60 MHz)

    PeakTech PeakTech 1240 2-ch Oscilloscope (60 MHz)

    1 in stock

    Digital storage osczilloscope of the latest generation with high-resolution color display, backlight, high bandwidth and high sampling rate, VGA-output, large internal memory, USB port and LAN connection for integration into networks. The amazing value for money and modern technology allows a wide range of applications in education, service and quality assurance area. High-resolution TFT color display with 800 x 600 pixels and 65536 colors USB port for real-time data transmission or reading of internal memory Saving of measured values and graphics directly onto the USB-stick VGA-output port for external monitor Autoset and autoscale function for easy operation LAN connection for remote access via network Internal memory of 10 million points per channel or 15 waveforms 20 automatic measurement modes and FFT function PASS/FAIL function Safety: EN 61010-1; CAT II Accessories: 2 pcs. BNC cable, USB cable, software CD for Windows 2000/XP/Vista/7/8/10, power cable, 2 probes, carrying case and manual Bandwidth 60 MHz Display 20 cm (8”) TFT with 65536 colors Resolution 800 x 600 Pixel Channel 2 CH Sampling mode normal/peak detect/average Sampling rate each Channel 250 MSa/s Input coupling AC, DC, GND Input impedance 1 MΩ +/- 2 % in parallel with 10 pF +/- 5 pF Input voltage 400 V DC or ACpp Sensitivity 2 mV - 10 V/Skt/div. Rise time < 5,8 ns Accuracy +/- 3 % Vertical resolutions 8 Bits (2 CH simultaneously) Horizontal scale 5ns-100s/Skt./div Sampling range 0,5 - 250 S/s Trigger type Edge/Video/Pulse/Slope Trigger mode Auto, Normal, Single Trigger coupling DC, AC, LF, HF 20 automat. measurements peak-peak, cycle RMS, Vmax, Vmin, Vtop, Vbase, Vamp, overshoot, preshoot, rise time, fall time, +width, -width, +duty, -duty, delay A→B (rising), delay A→B(falling), frequency, period, min, max Phase difference +/- 3° Record length 10.000.000 points/CH Interfaces USB Device 2.0, USB Host 2.0, VGA, LAN Operation voltage 100 ~ 240 V ACrms / 50/60 Hz Dimensions (WxHxD) 340 x 155 x 70 mm Weight 1.8 kg

    1 in stock

    € 499,00

    Members € 449,10

  • Last stock! UNI-T UPO1202CS 2-ch Oscilloscope (200 MHz)

    Uni-Trend UNI-T UPO1202CS 2-ch Oscilloscope (200 MHz)

    2 in stock

    UNI-T UPO1202CS is a multifunctional, low-cost 2-channel digital phosphor oscilloscope with 200 MHz bandwidth and 1 GSa/s sampling rate. It can be widely used in the fields of electronic and electrical design, debugging, education and industrial design. UPO1000CS series adopts parallel digital signal processing technology, which greatly improves the data processing speed and waveform capture rate. The original Ultra Phosphor technology can present the cumulative effect of the tested signal as a multi-layered afterglow. Compared with traditional digital storage oscilloscopes, the persistence of digital phosphor oscilloscopes can present three-dimensional waveform data of amplitude, time and signal intensity. Fast Acquire technology can accurately capture abnormal events such as video, jitter, noise and runt signals. Specifications UPO1102CS UPO1202CS Bandwidth 100 MHz 200 MHz Analog channels 2 2 Sampling rate 1 GSa/s 1 GSa/s Storage depth 56 Mpts per channel 56 Mpts per channel Rise time ≤3.5ns ≤1.8ns Capture rate 500,000 wfms/s 500,000 wfms/s Waveform record 100,000 frames 100,000 frames Features 7' WVGA (800 x 480) TFT LCD Ultra Phosphor super fluorescent display effect, up to 256 levels of gray display Support RS232, I²C, SPI, CAN and LIN trigger Innovative RS232, I²C, SPI, CAN and LIN hardware decoding Vertical scale: 1 mV/div-20 V/div Low background noise: <100 μVrms 1M points enhanced FFT function. Support frequency setting, waterfall diagram, detection setting and marker measurement etc 36 kinds of waveform parameters can be automatically measured Rich trigger functions (edge, pulse width, video, slope, runt, overshoot, delay, timeout, duration, setup and hold, Nth edge and pattern trigger) Multi-Scopes support dual-channel independent trigger fluorescence display Multi-channel independent 7-bit hardware frequency counter DVM supports dual-channel independent AC and DC true RMS measurement Waveform arithmetic functions (FFT, +, -, ×, ÷, digital filtering, logic operations, and advanced operations) Rich interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail) Support SCPI programmable instrument standard command Support WEB access and control Downloads Datasheet Programming Manual User's Manual Quick Start Guide Software

    2 in stock

    € 439,00

    Members € 395,10

  • UNI-T UPO1102CS 2-ch Oscilloscope (100 MHz)

    Uni-Trend UNI-T UPO1102CS 2-ch Oscilloscope (100 MHz)

    UNI-T UPO1102CS is a multifunctional, low-cost 2-channel digital phosphor oscilloscope with 100 MHz bandwidth and 1 GSa/s sampling rate. It can be widely used in the fields of electronic and electrical design, debugging, education and industrial design. UPO1000CS series adopts parallel digital signal processing technology, which greatly improves the data processing speed and waveform capture rate. The original Ultra Phosphor technology can present the cumulative effect of the tested signal as a multi-layered afterglow. Compared with traditional digital storage oscilloscopes, the persistence of digital phosphor oscilloscopes can present three-dimensional waveform data of amplitude, time and signal intensity. Fast Acquire technology can accurately capture abnormal events such as video, jitter, noise and runt signals. Specifications UPO1102CS UPO1202CS Bandwidth 100 MHz 200 MHz Analog channels 2 2 Sampling rate 1 GSa/s 1 GSa/s Storage depth 56 Mpts per channel 56 Mpts per channel Rise time ≤3.5ns ≤1.8ns Capture rate 500,000 wfms/s 500,000 wfms/s Waveform record 100,000 frames 100,000 frames Features 7' WVGA (800 x 480) TFT LCD Ultra Phosphor super fluorescent display effect, up to 256 levels of gray display Support RS232, I²C, SPI, CAN and LIN trigger Innovative RS232, I²C, SPI, CAN and LIN hardware decoding Vertical scale: 1 mV/div-20 V/div Low background noise: <100 μVrms 1M points enhanced FFT function. Support frequency setting, waterfall diagram, detection setting and marker measurement etc 36 kinds of waveform parameters can be automatically measured Rich trigger functions (edge, pulse width, video, slope, runt, overshoot, delay, timeout, duration, setup and hold, Nth edge and pattern trigger) Multi-Scopes support dual-channel independent trigger fluorescence display Multi-channel independent 7-bit hardware frequency counter DVM supports dual-channel independent AC and DC true RMS measurement Waveform arithmetic functions (FFT, +, -, ×, ÷, digital filtering, logic operations, and advanced operations) Rich interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail) Support SCPI programmable instrument standard command Support WEB access and control Downloads Datasheet Programming Manual User's Manual Quick Start Guide Software

    € 359,00

    Members € 323,10

  • Siglent SDS2354X Plus 4-ch Oscilloscope (350 MHz)

    Siglent Siglent SDS2354X Plus 4-ch Oscilloscope (350 MHz)

    Siglent's SDS2000X Plus series Digital Storage Oscilloscopes are available in bandwidths of 100 MHz, 200 MHz, and 350 MHz, have a maximum sample rate of 2 GSa/s, a maximum record length of 200 Mpts/ch, and up to 4 analog channels + 16 digital channels mixed-signal analysis ability. The SDS2000X Plus series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications that require more than 8-bit resolution. The large 10.1" capacitive touch screen supports multi-touch gestures, while the remote web control, mouse and external keyboard support greatly improve the operating efficiency of the SDS2000X Plus. Features 100 MHz, 200 MHz, 350 MHz (upgradable to 500 MHz) models Real-time sampling rate up to 2 GSa/s Record length up to 200 Mpts Serial bus triggering and decoder, supports I²C, SPI, UART, CAN, LIN, CAN FD, FlexRay, I²S and MIL-STD-1553B Provide 10 bit mode, Vertical and Horizontal Zoom Capacitive touch screen supports multi-touch gestures Siglent SDS2000X Plus Oscilloscopes   SDS2102X Plus SDS2104X Plus SDS2204X Plus SDS2354X Plus Bandwidth 100 MHz 100 MHz 200 MHz 350 MHz Channels 2 4 4 4 Real-time sampling rate 2 GSa/s 2 GSa/s 2 GSa/s 2 GSa/s Capture rate 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s Memory depth 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch Included Siglent SDS2354X Plus Oscilloscope Passive probes Power cord USB cable Manual Downloads Datasheet Manual Quick guide User manual Firmware

    € 3.149,00

    Members identical

  • Last stock! Siglent SDS2204X Plus 4-ch Oscilloscope (200 Mhz)

    Siglent Siglent SDS2204X Plus 4-ch Oscilloscope (200 Mhz)

    1 in stock

    Siglent's SDS2000X Plus series Digital Storage Oscilloscopes are available in bandwidths of 100 MHz, 200 MHz, and 350 MHz, have a maximum sample rate of 2 GSa/s, a maximum record length of 200 Mpts/ch, and up to 4 analog channels + 16 digital channels mixed-signal analysis ability. The SDS2000X Plus series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications that require more than 8-bit resolution. The large 10.1’’ capacitive touch screen supports multi-touch gestures, while the remote web control, mouse and external keyboard support greatly improve the operating efficiency of the SDS2000X Plus. Features 100 MHz, 200 MHz, 350 MHz (upgradable to 500 MHz) models Real-time sampling rate up to 2 GSa/s Record length up to 200 Mpts Serial bus triggering and decoder, supports I²C, SPI, UART, CAN, LIN, CAN FD, FlexRay, I²S and MIL-STD-1553B Provide 10 bit mode, Vertical and Horizontal Zoom Capacitive touch screen supports multi-touch gestures Siglent SDS2000X Plus Oscilloscopes   SDS2102X Plus SDS2104X Plus SDS2204X Plus SDS2354X Plus Bandwidth 100 MHz 100 MHz 200 MHz 350 MHz Channels 2 4 4 4 Real-time sampling rate 2 GSa/s 2 GSa/s 2 GSa/s 2 GSa/s Capture rate 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s Memory depth 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch Included Siglent SDS2204X Plus Oscilloscope Passive probes Power cord USB cable Manual Downloads Datasheet Manual Quick guide User manual Firmware

    1 in stock

    € 2.299,00

    Members identical

  • Last stock! Siglent SDS2104X Plus 4-ch Oscilloscope (100 MHz)

    Siglent Siglent SDS2104X Plus 4-ch Oscilloscope (100 MHz)

    1 in stock

    Siglent's SDS2000X Plus series Digital Storage Oscilloscopes are available in bandwidths of 100 MHz, 200 MHz, and 350 MHz, have a maximum sample rate of 2 GSa/s, a maximum record length of 200 Mpts/ch, and up to 4 analog channels + 16 digital channels mixed-signal analysis ability. The SDS2000X Plus series employs Siglent’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications that require more than 8-bit resolution. The large 10.1’’ capacitive touch screen supports multi-touch gestures, while the remote web control, mouse and external keyboard support greatly improve the operating efficiency of the SDS2000X Plus. Features 100 MHz, 200 MHz, 350 MHz (upgradable to 500 MHz) models Real-time sampling rate up to 2 GSa/s Record length up to 200 Mpts Serial bus triggering and decoder, supports I²C, SPI, UART, CAN, LIN, CAN FD, FlexRay, I²S and MIL-STD-1553B Provide 10 bit mode, Vertical and Horizontal Zoom Capacitive touch screen supports multi-touch gestures Siglent SDS2000X Plus Oscilloscopes   SDS2102X Plus SDS2104X Plus SDS2204X Plus SDS2354X Plus Bandwidth 100 MHz 100 MHz 200 MHz 350 MHz Channels 2 4 4 4 Real-time sampling rate 2 GSa/s 2 GSa/s 2 GSa/s 2 GSa/s Capture rate 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s 120,000 wfm/s Memory depth 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch 200 Mpts/ch Included Siglent SDS2104X Plus Oscilloscope Passive probes Power cord USB cable Manual Downloads Datasheet Manual Quick guide User manual Firmware

    1 in stock

    € 1.449,00

    Members identical

What is an oscilloscope? What are the advantages of a digital oscilloscope?

Oscilloscopes are electronic instruments that allow us to visualize different signals as a function of time on a 2D plot. Oscilloscopes come in a variety of sizes and can allow anyone with an interest in electronics – from students to makers to craftsmen – to discover how waveforms vary as a circuit is adjusted.

A digital oscilloscope is a useful tool for analyzing the response of a circuit, and it allows us to see on the screen what our eyes cannot see. With a digital oscilloscope you can test and debug the analog outputs of sensors, and you can verify and quickly analyze various parameters such as amplitude, frequency, and distortion.

When you look at an oscilloscope, you see the screen and the buttons for the vertical settings, the horizontal settings and the triggering. The display is usually a cathode ray tube (CRT), which is used not only for oscilloscopes, but also for other applications such as television and computer monitors. Its function is to convert an electrical signal into a visual representation.

What types of oscilloscopes are there? And what are the differences?

Today, digital oscilloscopes are the most popular type. An analog oscilloscope displays the waveform in its original form, while a digital oscilloscope samples the original analog waveform and converts the result into digital numbers, then stores it in digital format.

Another important type of oscilloscope is the USB oscilloscope. It is operated via a computer or tablet using a USB port. The USB oscilloscope has one or more analog channels, possibly digital channels, and buttons or switches for operation.

USB oscilloscopes are less expensive than traditional ones because the graphics are provided by the host PC. An A/D converter and a USB interface are all that is needed for a USB oscilloscope. Furthermore, USB oscilloscopes are usually small and can be used in places where access is limited. Moreover, they are a great solution for applications that require flexibility, as they are a great portable option.

An automotive oscilloscope is a necessary instrument for detecting malfunctions in all kinds of electronic components in vehicles. Moreover, it is often used by car technicians for car diagnostics. The only difference between an automotive oscilloscope and a digital oscilloscope is that it offers additional capabilities for testing and diagnosis.

What is a PicoScope?

PicoScope is computer software that allows Pico Technology oscilloscopes to measure real-time signals. A PicoScope PC oscilloscope is an application for measuring and testing all electrical components and circuits in vehicles. Your PC can become a powerful diagnostic tool with the help of a PicoScope.

Buy an oscilloscope. What does Elektor have to offer?

An oscilloscope is an essential tool for anyone who works with electronic circuits. It is useful if you want to get to know the behavior of your project and detect errors in your circuits.

Elektor offers a wide choice of oscilloscopes in various sizes and with varying specifications, including bandwidth, vertical resolution, and horizontal scale. In addition, we offer a selection of oscilloscopes that are very suitable for a number of areas of interest. Some of the most popular products Elektor sells are the PicoScope 2204A USB Oscilloscope and the SmartScope USB oscilloscope, which provide a complete electronics lab in one compact, low-cost, USB-powered device. The affordable PicoScope and SmartScope models are ideal for education, hobby and field use.

What accessories are there for oscilloscopes?

Digital oscilloscopes usually come with a set of probes. In addition to scopes, Elektor sells a range of related products, including cables and DIY kits.

Why should you buy an oscilloscope from Elektor?

Electrical engineers, makers and electronics enthusiasts turn to Elektor for affordable, high-quality test and measurement equipment such as oscilloscopes. We stock a range of oscilloscopes – from portable handheld devices to high-end desktop solutions – to meet the different needs of a wide audience.

Login

Forgot password?

Don't have an account yet?
Create an account