The Soldered CONNECT Programmer is designed to make programming boards based on ESP8266 and ESP32 microcontrollers extremely simple. It contains all the necessary electronics and logic, allowing programming to be done by simply plugging a USB cable into the CONNECT Programmer and connecting it to the programming header. The onboard circuitry handles timing and signal sequencing automatically, placing the ESP microcontroller into bootloader mode without the need for manual intervention.
Features
IC: CH340
Pin layout: GPIO0, RESET, RX, TX, 3V3, GND
LEDs: RX, TX, power
Interface: USB-C
Dimensions: 38 x 22 mm
Downloads
Datasheet
GitHub
If you are looking for an easy way to get started with soldering or simply want to make a small portable gadget, this set is a great opportunity. "LED cube" is an educational set for learning the soldering skill, with which you get a small electronic game at the end. After you turn on and shake this board, certain leds will light up randomly and symbolize the number, as if a real die had been thrown.
It is based on the Attiny404 microcontroller, programmed in Arduino, and there is a battery on the back which makes this gadget portable. There is also a keychain so you can always carry your new game with you! Soldering is easy according to the markings on the board.
Included
1x PCB
1x ATtiny404 microcontroller
7x LEDs
7x Resistors (330 ohm)
1x Resistor (10 kohm)
1x Battery holder
1x CR2032 battery
1x Switch
1x Vibration sensor SW-18020P
1x Keychain ring
This flux paste glue dispenser is crafted from durable hard plastic and iron, ensuring long-lasting use. The lead screw advances by 0.75 mm with each rotation, providing precise and controlled dispensing. Its ergonomic, labor-saving design enhances efficiency, making your repair work more effective. It is compatible with 5cc to 10cc solder flux paste. (Note: Solder flux is NOT included!)
Dimensions: 107 x 48 mm
Flux paste holder diameter: 19 mm
If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Reaction game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The goal of the game is to press the button next to the LED as soon as it turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get?
It’s based on ATtiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB.
Included
1x PCB
1x ATtiny404 microcontroller
4x LEDs
4x Pushbuttons
1x Switch
4x Resistors (330 ohm)
1x CR2032 battery holder
1x Battery CR2032
1x Keychain holder
If you are looking for a simple way to learn soldering, or just want to make a small gadget that you can carry, this set is a great opportunity. Stop me game is an educational kit which teaches you how to solder, and in the end, you get to have your own small game. The LEDs go up and down, and your goal is to press the button as soon as the green LED turns on. With every correct answer, the game gets a bit harder – the time you have to press the button shortens. How many correct answers can you get?
It’s based on ATtiny404 microcontroller, programmed in Arduino. At its back, you’ll find CR2032 battery which makes the kit portable. There’s keychain holder as well. Soldering process is easy enough based on the mark on the PCB.
Included
1x PCB
1x ATtiny404 microcontroller
7x LEDs
1x Pushbutton
1x Switch
7x Resistors (330 ohm)
1x CR2032 battery holder
1x Battery CR2032
1x Keychain holder
If you’re looking for a simple way to start soldering or just want to make your own Dasduino, this soldering set is a great opportunity. "Make your own Dasduino CORE" is an educational set for learning the skill of soldering, with which you end up with a functional microcontroller board. As with the other SMD versions of the Dasduino CORE boards we offer, the possibilities are endless.
It is based on the ATmega328P microcontroller, and all SMD components are already soldered on the board. The set also includes a THT socket for the microcontroller, which simplifies the replacement of the microcontroller should it ever become necessary.
Included
1x PCB
7x Capacitors (100nF)
4x Capacitors (2.2uF)
2x Capacitors (22pF)
5x Resistors (2.2 kOhm)
5x Resistors (10 kOhm)
3x Resistors (1 kOhm)
1x Resistor (100 kOhm)
1x Resistor (100 ohm)
1x JST battery connector
1x LED (purple)
1x LED (white)
1x LED (blue)
1x LED (red)
1x LED (orange)
1x Socket for ATmega328P
1x ATmega328P microcontroller
This set contains 4 soldering tips for the temperature-controlled digital soldering station ZD-8961-A. Included 1x Soldering tip N8-1 1x Soldering tip N8-2 1x Soldering tip N8-3 1x Soldering tip N8-4
The PCW10A soldering mat is the ultimate solution for any soldering or repair project. Measuring 450 x 300 mm, this silicone mat provides a generous work surface that is heat-resistant up to 450°C, making it ideal for use with a range of (soldering) tools and equipment. It is the perfect size for your workbench and provides ample space for all your tools and components. The PCW10A soldering mat comes with several convenient features to make your repair work easier and more efficient. The built-in storage boxes provide a convenient place to keep your tools and components organized, while the powerful magnets hold small parts securely in place. These features ensure that you can work more efficiently and effectively, reducing the risk of lost or misplaced items. The PCW10A soldering mat also features a non-slip surface that provides a stable and secure work environment, preventing your equipment from slipping or sliding during use. Additionally, the mat is easy to clean, allowing you to maintain a hygienic workspace that is free of debris and other contaminants. In addition, the mat also features a printed grid to help you measure and cut materials accurately. Whether you are a professional technician or a DIY enthusiast, the PCW10A soldering mat is an essential tool for anyone who needs a reliable and durable work surface for their repair and soldering projects. With its durable construction, ample workspace, and convenient storage options, you can tackle any project with confidence and ease. Features Silica gel working mat (blue) Size: 450 x 300 mm Edge thickness: 6.5 mm Various magnetic sections 3 storage boxes Heat-resistant 450°C
