Raspberry Pi Power Supplies

19 products


  • Official EU Power Supply for Raspberry Pi 4 (black)

    Raspberry Pi Foundation Official EU Power Supply for Raspberry Pi 4 (black)

    The Raspberry Pi USB-C power supply is designed specifically to power the latest Raspberry Pi 4 Model B computers. The power supply features a USB-C cable and is available in four different models to suit different international power sockets, and in two colors. Specifications Output Output voltage +5.1 V DC Minimum load current 0 A Nominal load current 3.0 A Maximum power 15.3 W Load regulation ±5 % Line regulation ±2 % Ripple & noise 120 mVp-p Rise time 100 ms maximum to regulation limits for DC outputs Turn-on delay 3000 ms maximum at nominal input AC voltage and full load Protection Short circuit protectionOvercurrent protectionOver temperature protection Efficiency 81% minimum (output current from 100%, 75%, 50%, 25%)72% minimum at 10% load Output cable 1.5 m 18AWG Output connector USB Type-C Input Voltage range 100 - 240 Vac (rated)96 - 264 Vac (operating) Frequency 50 / 60 Hz ± 3 Hz Current 0.5 A maximum Power consumption (no load) 0.075 W maximum Inrush current No damage shall occur, and the input fuse shall not blow Operating ambient temperature 0 - 40 °C

    € 9,95

    Members identical

  • Official EU Power Supply for Raspberry Pi 4 (white)

    Raspberry Pi Foundation Official EU Power Supply for Raspberry Pi 4 (white)

    The Raspberry Pi USB-C power supply is designed specifically to power the latest Raspberry Pi 4 Model B computers. The power supply features a USB-C cable and is available in four different models to suit different international power sockets, and in two colors. Specifications Output Output voltage +5.1 V DC Minimum load current 0 A Nominal load current 3.0 A Maximum power 15.3 W Load regulation ±5 % Line regulation ±2 % Ripple & noise 120 mVp-p Rise time 100 ms maximum to regulation limits for DC outputs Turn-on delay 3000 ms maximum at nominal input AC voltage and full load Protection Short circuit protectionOvercurrent protectionOver temperature protection Efficiency 81% minimum (output current from 100%, 75%, 50%, 25%)72% minimum at 10% load Output cable 1.5 m 18AWG Output connector USB Type-C Input Voltage range 100 - 240 Vac (rated)96 - 264 Vac (operating) Frequency 50 / 60 Hz ± 3 Hz Current 0.5 A maximum Power consumption (no load) 0.075 W maximum Inrush current No damage shall occur, and the input fuse shall not blow Operating ambient temperature 0 - 40 °C

    € 9,95

    Members identical

  • Official Micro-USB Power Supply for Raspberry Pi

    Raspberry Pi Foundation Official Micro-USB Power Supply for Raspberry Pi

    Official Micro-USB Power Supply for Raspberry Pi (12.5 W) Input: 100-240 VAC Output: 5.1 V / 2.5 A power supply Connector: micro USB Length: 1.5 m

    € 9,95

    Members identical

  • USB-A to USB-C Cable with ON/OFF Switch

    Kuongshun USB-A to USB-C Cable with ON/OFF Switch

    Features Type C cable USB type C is suitable for new version Raspberry Pi 4 No need to pull the cable to restart or reboot your Pi, just press the button to turn your Pi on and off Can be used as power supply for the Pi up to 2 Amp Help prevent the Pi's USB connector from wear and tear due to frequently pulling and inserting the USB cable Specifications Interface: USB Type C Current: 3 A Length: 1.5 m Use for: Raspberry Pi 4 Model B Packing List: 1x USB Type C power cable

    € 4,95

    Members € 4,46

  • Official 27 W Power Supply for Raspberry Pi 5 (EU, white)

    Raspberry Pi Foundation Official 27 W Power Supply for Raspberry Pi 5 (EU, white)

    The Raspberry Pi 27 W PD USB-C power supply is designed specifically to power the Raspberry Pi 5. It is also capable of delivering 5 V/3 A, 9 V/3 A, 12 V/2.25 A, 15 V/1.8 A to PD-compatible products, making it a good and cost-effective power supply for many general applications, such as charging smartphones and tablets. Specifications Input 100-240 VAC Output 5 A @ 5.1 V, 3 A @ 9 V, 2.25 A @ 12 V, 1.8 A @ 15 V Connector USB-C Length 1.2 m Color White Region EU

    € 13,95

    Members identical

  • RTC Battery for Raspberry Pi 5

    Raspberry Pi Foundation RTC Battery for Raspberry Pi 5

    The power-management IC used on Raspberry Pi 5 integrates a real-time clock, and charging circuitry for a button cell which can power the clock while main power is disconnected. This Panasonic ML-2020 lithium manganese dioxide battery with a two-pin plug and a double-sided adhesive pad can be connected directly to the battery connector of the Raspberry Pi 5 and attached to the inside of a case or another convenient location.

    € 7,95

    Members identical

  •  -20% 5 V/2 A Micro-USB Voeding (EU)

    € 9,95€ 7,95

    Members identical

  • USB-A to Micro USB-B Cable with Switch

    JOY-iT USB-A to Micro USB-B Cable with Switch

    USB-A to Micro USB-B power cable (power supply only) 1.5 m length with ON/OFF switch Add the ability to control the power to your USB-powered project simply by plugging a cable with a switch between the USB power port and the USB cable. There's no more need to pull the cable to restart or reboot your devices, just press the button to turn on and off, which helps to prevent the USB connector from wear and tear due to frequent pulling and inserting the USB cable. It can be used as a power supply up to 2 A. Not applicable for data transfer.

    € 4,95

    Members € 4,46

  • StromPi 3 – Power Solution voor Single Board Computers

    JOY-iT StromPi 3 - Power Solution for Single Board Computers

    With the StromPi 3, JOY-iT has now released the next expansion board that's going to meet your power requirements. With a voltage range of 6-61 V and a current of up to 3 A, even larger projects can be supplied with sufficient current. The individual inputs can now be prioritised in various ways, allowing the StromPi 3 to be perfectly customised to your project. In addition to the voltage inputs already available, the new StromPi 3 can now be supplemented with an optional plug-in battery unit that adds a rechargeable emergency power source to your Raspberry Pi with a LiFePO4 battery. As a result, unexpected power outages are in the past! Along with that, the StromPi 3 now has its own configurable and autonomously acting microsystem unit, which can be used for a programmable start-stop behaviour. Let your system run up and down at preset times to perform measurements or to switch devices on and off (also ideal for digital signage or machine control). The RTC (real-time clock) contained in the microsystem can also be used to synchronize the operating Raspberry Pi without Internet access. With the new StromPi 3 you are perfectly equipped for all kinds of projects! Specifications Voltage Input Micro-USB, Wide-Range: 6-61 V Voltage Output 5 V, 3 A / RPi-PinHeader + USB Compatible to Raspberry Pi (A+, B+, 2B, 3, 3B, 3B+, 4B), Banana Pi M2, via USB output: many more single board computers like Arduino, pcDuino, Red Pitaya and many more Optional Extensions Plug-in battery pack (sold separately) with a 1000 mAh LiFePO4 battery unit Microcontroller Control Programming option by prioritizing the individual inputs in an emergency (Power Path) Addional Features RTC real-time clock (programmable start/stop behaviour), control via serial interface (data output, control), optional rechargeable battery is charged immediately during operation Dimensions 55 x 54 x 20 mm Downloads Manuals, scripts and firmware

    € 69,95

    Members € 62,96

  • Power Supply for Raspberry Pi Build HAT (48 W)

    Raspberry Pi Foundation Power Supply for Raspberry Pi Build HAT (48 W)

    This 48 W (8 VDC, 6 A) power supply is designed for the use with the Raspberry Pi Build HAT. Input: 110-240 VAC Output: 8 VDC, 6 A Cable: 1.5 m, 16 awg

    € 17,95

    Members identical

  • Official 27 W Power Supply for Raspberry Pi 5 (EU, black)

    Raspberry Pi Foundation Official 27 W Power Supply for Raspberry Pi 5 (EU, black)

    The Raspberry Pi 27 W PD USB-C power supply is designed specifically to power the Raspberry Pi 5. It is also capable of delivering 5 V/3 A, 9 V/3 A, 12 V/2.25 A, 15 V/1.8 A. to PD-compatible products, making it a good and cost-effective power supply for many general applications, such as charging smartphones and tablets. Specifications Input 100-240 VAC Output 5 A @ 5.1 V, 3 A @ 9 V, 2.25 A @ 12 V, 1.8 A @ 15 V Connector USB-C Length 1.2 m Color Black Region EU

    € 13,95

    Members € 12,56

  • Last stock! Waveshare PoE Ethernet/USB Hub Box for Raspberry Pi Zero (3x USB 2.0, 802.3af-Compliant)

    Waveshare Waveshare PoE Ethernet/USB Hub Box for Raspberry Pi Zero (3x USB 2.0, 802.3af-Compliant)

    2 in stock

    The PoE-ETH-USB-Hub-Box is a Hub kit with PoE/ETH/USB Hub HAT inside. It is tailored for Raspberry Pi Zero series, small in size, each cut-out of the case is exactly aligned with the connector. The case adopts classic Raspberry Pi red/white color combination, with quality dull polish surface, effectively keeping the Zero away from dust. By using this small Hub Box and some proper 802.3af-compliant power sourcing equipments, it is possible to provide both network connection and power supply for your Raspberry Pi Zero in only one Ethernet cable, along with 3x extended USB ports. Features Designed for Raspberry Pi Zero, compatible with Zero series boards Incorporates RTL8152B Ethernet chip, with 10M / 100M auto-negotiation RJ45 port PoE (Power over Ethernet) feature, 802.3af-compliant Fully isolated SMPS (Switch Mode Power Supply) 3x extended USB ports, compatible with USB 2.0 / 1.1 Angle rounded design, smooth hand feeling, 'simple snap' case lid Quality ABS material, dull polish surface, anti-fingerprint Comes with two different lids, changing as you like Included 1x PoE/ETH/USB Hub HAT kit 1x ABS case 1x Rubber feet 4pcs 1x Screws pack Downloads Documentation

    2 in stock

    € 29,95

    Members € 26,96

  • Witty Pi 4 – Real-time Klok en Power Management voor Raspberry Pi

    Witty Pi 4 - Real-time Clock and Power Management for Raspberry Pi

    Witty Pi is an add-on board that adds realtime clock and power management to your Raspberry Pi. It can define your Raspberry Pi’s ON/OFF sequence, and significantly reduce the energy usage. Witty Pi 4 is the fourth generation of Witty Pi and it has these hardware resources onboard: Factory calibrated and temperature compensated realtime clock with ±2 ppm accuracy. Dedicated temperature sensor with 0.125 °C resolution. On-board DC/DC converter that accepts up to 30 V DC. AVR 8-bit microcontroller (MCU) with 8 KB programmable flash. Accurate realtime clock and ON/OFF scheduling The realtime clock (RTC) on Witty Pi 4 has been calibrated in the factory and Witty Pi 4’s firmware also makes temperature compensation for the crystal. This makes the RTC very accurate and the actual annual error is limited within ±2 ppm. When your Raspberry Pi boots up, the time stored in the RTC will overwrite the system time. As a result, your Raspberry Pi knows the correct time even without accessing the Internet. You can schedule the startup and/or shutdown of your Raspberry Pi, and make it a time-controlled device. You can even define a schedule script to schedule complicated ON/OFF sequence for your Raspberry Pi. Scheduling the ON/OFF sequence for Raspberry Pi is the most popular feature of Witty Pi, and it is extremely useful for systems that powered by battery. By only turning on Raspberry Pi when necessary, the battery can be used way much longer with Witty Pi installed. Temperature-controlled device The temperature sensor on Witty Pi 4 has 0.125 °C resolution. The temperature data is used for compensating the crystal and make the RTC more accurate. You can also specific the action (startup or shutdown) when temperature goes above or below the preset threshold. Which means you can also make your Raspberry Pi a temperature-controlled device. DC/DC converter and e-latching power switch Witty Pi 4 comes with a DC/DC converter on board, which allows you to power your device with 6~30V power supply. You can also power your device with 5 V via the USB type C connector. Witty Pi 4 also implements an e-Latching power switch, which is very similar to the power switch on your PC/Laptop computer. You can gracefully turn on/off your Raspberry Pi with a single tap on the button. The software running in background will execute the shutdown command before the power gets cut, this avoid the data corruption caused by hard shutdown. Witty Pi 4 supports all Raspberry Pi models that has the 40-pin GPIO header, including A+, B+, 2B, Zero, Zero W, Zero 2 W, 3B, 3B+, 3A+ and 4B. You will need to solder the 40-pin header to Zero/Zero W/Zero 2 W model beforehand, so they can make reliable connection with Witty Pi. Single I²C device Witty Pi 4 uses MCU to emulate a single I²C device with default address 0x08, and also map all I²C registers in realtime clock and temperature sensor as virtual I²C registers in the same device. You can access all I²C registers in realtime clock and temperature sensor via the single I²C device emulated by Witty Pi 4. The advantage of this new design is that Witty Pi 4 hides other I²C devices (realtime clock, temperature sensor) and becomes the proxy of them to talk to Raspberry Pi. Because the I²C address used by Witty Pi 4 can be changed to any value, you can always avoid the I²C address conflicting. UWI support Witty Pi 4 is fully supported by UWI (UUGear Web Interface), and you can access you Witty Pi 4 on any device that have network access. Specifications Microcontroller ATtiny841 (datasheet) Realtime Clock PCF85063A (datasheet), calibrated in factory Temperature Sensor LM75B (datasheet) DC/DC Converter MP4462 (datasheet) MOSFET Switch AO4616 (datasheet) Battery CR2032 (for time keeping when power supply is disconnected) Power In DC 5 V (via USB type C connector)or DC 6 V~30 V (via XH2.54 connector) Output Current Up to 3 A for Raspberry Pi and its peripherals Standby Current ~0.5 mA Operating Environment Temperature -30°C~80°C (-22°F~176°F)Humidity 0~80% RH, no condensing, no corrosive gas Dimension 65 x 56 x 19 mm Weight 23 g (without accessories) Included 1x Witty Pi 4 board 1x CR2032 battery 4x M2.5 x 11mm Copper Standoff 8x M2.5 screws Downloads User manual GitHub

    € 44,95

    Members € 40,46

  • JOY-iT Aluminium Case for StromPi 3

    JOY-iT JOY-iT Aluminium Case for StromPi 3

    Material: Aluminium Color: Matt black Compatible with: Raspberry Pi 2, 3 and 4 with attached StromPi 3 and Battery Hat Options of Mounting: DIN rail, M4 threaded holes on the bottom of the case Amounts of M4 threads: 4 Active cooling Low-profile heatsink and PCB for fan control and power button included Dimensions: 59 mm x 64 mm x 105 mm

    € 29,95

    Members € 26,96

  • JOY-iT Extra Large Battery Pack for StromPi 3

    JOY-iT JOY-iT Extra Large Battery Pack for StromPi 3

    3 in stock

    This battery hat with LiFePO4 battery turns the StromPi V3 into a full-featured UPS solution. The replacement battery is provided as third current source, is surveilled and will be recharged automatically. With the doubling of the rated capacity, the lifespan is nearly twice as long as well in comparison to the 1000 mAh battery. It is based of the LiFePo4 technoloy and offers more essential advantages compared to the standard lithium-ION structures: increased security because there can not be a chemical spontaneous combustion a longer life time as lithium ION technology more charge cycles the battery gets automatically charged if it runs with a external voltage source In the battery electronic, protection circuits against overload, short-circuits and deep discharging are integrated. SPECIFICATIONS TYPE Lithium iron phosphate (LiFePO4) CAPACITY 2000 mAh VOLTAGE 3.2 V SPECIAL FEATURES directly attachable to the StromPi 3, will be charged immediately, pin header lead-through, own protection- and charge electronic, More Security: no chemical self ignition possible, Essentially longer Lifespan than Lithium-Ion technology DIMENSIONS 65 x 56 x 22 mm ITEMS SHIPPED Battery Pack EAN 4250236819891 ARTICLE NO. RB-StromPi3BAT-XL

    3 in stock

    € 49,95

    Members € 44,96

  • Pimoroni Pico LiPo

    Pimoroni Pimoroni Pico LiPo

    Pimoroni Pico LiPo is powered and programmable via USB-C and comes with 16 MB of QSPI (XiP) flash. With the Qwiic/STEMMA QT connector you can hook up a whole host of different sensors and breakouts, and a debug connector for if you want to do your programming using a SWD debugger. There is an on/off button and a BOOTSEL button, which can also be used as a user switch.Pimoroni Pico LiPo also has onboard LiPo/LiIon battery management – the inbuilt charging circuitry means charging your battery is as easy as plugging your Pimoroni Pico Lipo in via USB. Two indicator LEDs connected to the battery circuit keep you informed of on/off state and charging status and it's compatible with any of our LiPo, LiIon and high capacity LiPo batteries.Programmable with C++, MicroPython or CircuitPython, Pimoroni Pico LiPo is the perfect powerhouse for your portable projects.Features Powered by RP2040 Dual ARM Cortex M0+ running at up to 133 Mhz 264 kB of SRAM 16 MB of QSPI flash supporting XiP MCP73831 charger with 215 mA charging current (datasheet) XB6096I2S battery protector (datasheet) USB-C connector for power, programming, and data transfer 4 pin Qw-ST (Qwiic / STEMMA QT) connector 3 pin debug connector (JST-SH) 2-pole JST PH battery connector, with polarity marked on the board Switch for basic input (doubles up as DFU select on boot) Power button Power, charging and user LED indicators On-board 3V3 regulator (max regulator current output 600mA) Input voltage range 3 - 5.5 V Compatible with Raspberry Pi Pico add-ons Measurements: approx 53 x 21 x 8 mm (L x W x H, including connectors) Downloads CircuitPython Getting started with CircuitPython guide

    € 19,95

    Members € 17,96

  • PoE Splitter (5 V) – Power over Ethernet for Single Board Computers

    JOY-iT PoE Splitter (5 V) - Power over Ethernet for Single Board Computers

    Features Jack: 1x Micro USB power plug + 1x RJ45 output port Input Voltage: 36~57 V (standard PoE voltage 48 V, 52 V) Output Voltage: DC 5 V Output Current: 2 A Transmission Distance: 10~100 m PoE Protocol: IEEE802.3af Network Bandwidth: 10/100 Mbps Weight: 40 g Product Dimension: 82 x 28 x 23 mm Cable Length: 205 mm Operation Temperature: -50 °C up to +75 °C

    € 16,95

    Members € 15,26

  • Battery Unit for StromPi 3

    JOY-iT Battery Unit for StromPi 3

    3 in stock

    StromPi sends you an e-mail when his backup battery is flat! Technical details Battery type Lithium iron phosphate (LiFePO4) Capacity 1000 mAh Voltage 3.2 V Features Can be plugged directly to the StromPi 3 Charges immediately on StromPi 3 Own protection circuitry Own charging electronics Increased safety, as chemical self-ignition is not possible Significantly longer life than lithium-ion technologies Wide operating temperature range To our customers residing outside Europe: This product is prohibited from shipment by air!

    3 in stock

    € 34,95

    Members € 31,46

  • Last stock! Solar Panel 6 W for PiJuice

    Pi Supply Solar Panel 6 W for PiJuice

    2 in stock

    Features Portability - a 6 W panel that folds down into a super compact size. Easy to pack up and go Easily mountable - metal eye-holes in each corner (4 total) allow easy attachment to backpacks, trees, or tents Water resistant up to IPX4 rating One Regulated 5v/1A USB output - it works with your PiJuice, smartphones, tablets, audio players and more! Features SunPower solar panels which provide an industry-leading solar conversion efficiency Specification Solar panel - 5.5 V / 6 W Regulated Max output - 5 V / 5 W Single USB max output - 5 W Built-in smart-power chip Folded dimensions - 16.3 cm x 15.6 cm x 2.5 cm Unfolded dimensions - 32.8 cm x 15.6 cm x 2.4 cm Weight - 320 g CE and FCC tested Includes PiJuice Solar Panel - 6 W USB to microUSB Cable User Manual

    2 in stock

    € 49,95

    Members € 44,96

Officiële Raspberry Pi voeding

Met de krachtige en veelzijdige Raspberry Pi heb jij een single-board computer. Deze kun je voor een breed scala aan toepassingen inzetten, zolang deze maar van stroom voorzien is. De voeding voor jouw single-board computer is stap 1 naar het uiteindelijk kunnen gebruiken van jouw Raspberry.

Deze categoriepagina biedt je alle informatie die je nodig hebt over Raspberry Pi-voedingen, zodat je er zeker van kunt zijn dat je apparaat de juiste stroom krijgt.

We gaan in op de verschillende soorten Raspberry Pi-voedingen die beschikbaar zijn, hoe je de juiste kiest voor je apparaat en de voordelen en nadelen van elke optie. We geven ook tips over hoe je je Raspberry Pi-voeding kunt onderhouden en oplossen om een optimale prestatie te garanderen.

Soorten Raspberry Pi-voedingen

Er zijn twee opties om jouw Pi van stroom te voorzien en te voeden.

MicroUSB-voedingen voor Raspberry Pi

Dit is de meest voorkomende manier van stroomvoorziening. Met een Micro USB-kabel verbind je jouw Pi aan een laptop of muuradapter. Deze voeding is meestal klein en licht, en makkelijk aan te sluiten op je apparaat. Het nadeel van dit type voeding is dat ze niet voldoende stroom leveren voor het zware werk met veeleisende toepassingen.

AC-adapter voedingen voor Raspberry Pi

AC-adapters zijn ideaal voor het leveren van een betrouwbare stroomvoorziening voor je Raspberry Pi. Dit type voeding is meestal groter en zwaarder dan Micro USB-voedingen, maar je hebt een consistente stroomoutput.

Hoe kies je de juiste Raspberry Pi-voeding

Voordat je een product besteld om jouw Pi te voeden is het goed om stil te staan bij de toepassingen die je voor ogen hebt. Zorg ervoor dat de voeding die je kiest past bij de stroomuitgang die het product kan leveren. Overweeg ook de grootte en het gewicht van de voeding.

Onderhouds- en probleemoplossingstips

Langer genieten van jouw Raspberry Pi doe je door regelmatig onderhoud en controles uit te voeren. Denk bijvoorbeeld aan het schoonmaken van de contacten. Zo komt de elektrische verbinding nooit in het gedrang. Een andere praktische tip is om de spanning van de voeding te controleren op stabiliteit. Daarnaast zorg je ervoor dat de voeding niet te warm wordt want een te warme voeding kan problemen opleveren.

Koop je Raspberry Pi voeding bij Elektor

Elektor is dé specialist op gebied van hobby-elektronica in Nederland. Met ons grote assortiment ben je vrijwel verzekerd dat je kunt vinden waar je naar zoekt, aangeboden voor een scherpe prijs! Vanaf € 100,- betaal je bovendien geen verzendkosten. Bestel de nieuwe voeding voor je Raspberry Pi vandaag nog!

Login

Forgot password?

Don't have an account yet?
Create an account