If you are going to be drilling, we recommend drilling on FR1 substrates. Unlike FR4, FR1 dust does not contain fiber glass. It is also a softer material, which means a less wear and tear on the drill bits. Download the template and incorporate them into your design here. 10 substrates included.
When you start to run out of space in your design, migrate over from the small substrates to these. These substrates are made of FR1 – which means they don't contain fibreglass. There is less wear on the drill bits. Download the template and incorporate them into your design here. 6 substrates included.
These boards are the maximum substrate size the V-One can handle. Just clamp them to the printing platform and press print to dispense the ink.
Pack of 6
Exact size is 4” x 5.3”
Need to dispense your own UV sensitive fluids (up to 550nm)?
Included
4x 5cc UV-Blocking Syringe Barrels
4x Standard Fit Pistons (white)
4x High Viscosity Fit Pistons (red)
4x Tip Caps
4x End Caps
2x Female to Female Luer couplers
The Conductor 3 ink is optimized for printing both rigid and flexible circuits. The printer lays down silver conductive ink to make the traces and pads that comprise your circuit board. After thermal curing, the ink is conductive and ready for reflow.
Specificaties
Recommended curing temperature is 90°C for 5 minutes, then 120°C for 20 minutes (temperature measured at ink surface).
Compatible with FR1, FR4, and flexible substrates.
For best results, cure immediately after printing.
Solder with tin-bismuth-silver solder wire and flux at 180°C, or use preset profile for reflow soldering.
Note: Cartridges must be kept refrigerated, and have a shelf life of 12 months.
A set of high precision drill bits, covering the most common drill bit sizes. Just pop them in the V-One Drill with a 2.5 mm hex key (not included) and start drilling. The following sizes are included (2 of each): 0.70 mm 0.80 mm 0.90 mm 1.00 mm 1.60 mm
If you're hand soldering components with the provided solder wire, make sure to use flux to promote solder wetting. Out of solder wire? The wire in our store has been tested for best performance with the conductive ink and standard copper.
The Hello World circuit is the first circuit you print with your V-One. Have more than one person using your V-One? Then you might want more Hello World kits!The Hello World kit contains:
6x Green LEDs
3x 47k Resistors
3x 180R Resistors
3x 100k Resistors
3x 4.7UF Capacitor
1x 555 timer
1x 9V battery
Looking to dispense materials with a lower viscosity? These are the nozzles for you. Don't use this with our standard ink or solder paste... that will result in poor performance.This pack contains 4 extra fine nozzles with an internal diameter of 0.100 mm (4 mil)
If you want to push the resolution limits of the V-One, these dispensing tips will help enable your experimental projects. This pack contains 4 extra fine nozzles with an internal diameter of 0.150 mm (6 mil).
Do not use with solder paste! It will clog!
Keep printing with a pack of 4 nozzles (225 micron inner diameter). These metal dispensing tips offer excellent resolution and accurate deposition of ink and solder paste.
The Punk Console circuit is an advanced tutorial to get you familiar with the V-One Drill attachment. Learn how to create a double sided board and turn the knobs to create music! The kit contains: 2x Green LEDs 8x 1k Resistors 3x 0.01uF Capacitor 2x 500K Trimpots 1x 556 Timer 1x Piezo Buzzer 1x 9 V Battery 1x 9 V Battery Connector Rivets and a V-One Drill are required.
Use the right tool for the right job. These steel stakes are used to press the rivets on the PCB after holes have been drilled. They have been designed for optimum performance on the ink and ensure an electrical connection between the top and bottom layers of your PCB. Learn how to use them here.
Use the right tool for the right job. These steel stakes are used to press the rivets on the PCB after holes have been drilled. They have been designed for optimum performance on the ink and ensure an electrical connection between the top and bottom layers of your PCB. Learn how to use them here.
Do you need a way to connect the top and bottom layers? Rivets are the key!Rivets are little copper tubes that make a mechanical connection between the top and bottom layer. We found rivets to be the easiest way to create vias. Be sure to pick up the corresponding rivet tool if you don't have one!
Pack of 200
Inner Diameter - 0.4mm
Head Diameter - 0.9mm
Drill Size: 0.7mm
Confused on how to use them? Checkout our tutorial here.
Do you need a way to connect the top and bottom layers? Rivets are the key!Rivets are little copper tubes that make a mechanical connection between the top and bottom layer. We found rivets to be the easiest way to create vias. Be sure to pick up the corresponding rivet tool if you don't have one!
Pack of 200
Inner Diameter - 1.0mm
Head Diameter - 2.2mm
Drill Size: 1.5mm (or 1.6mm)
Confused on how to use them? Checkout our tutorial here.
To protect the V-One from any damage during drilling, mount this piece of FR1 on the heated bed and clamp your substrate on top. The V-One Drill attachment will perforate your substrate but won't make it through this layer so your heated bed stays intact. Only one is included, but don't worry, the sacrifical layer can be reused plenty of times.
T5 Particle size. Smaller particles means less clogging and more consistent dispensing!Fed up with ordering multiple stencils in between board iterations?Just snap on this RoHS solder paste cartridge and the V-One will dispense solder paste onto the pads of your board. Solder paste can be dispensed onto your V-One printed boards, or prefabricated circuit boards.
Particle Size: T5
Alloy: Sn42Bi57.6Ag0.4
Each cartridge prints approximately 11,000 0603 pads.
1 x 2mL cartridge
Use with 225um or 150um nozzles for best performance.
Done printing? Let’s add some components! Just be sure to use the Voltera recommended solder wire and plenty of flux to ensure a strong solder joint. Voltera has chemically tested it to be most compatible with their ink.
Alloy: Sn42 Bi57 Ag1
Dia: 1.0 mm
Flux: 2%
Weight: 20g
Recommended Temp: < 205°C (400°F)
RoHS Compliant
