Search results for "additional OR camera OR for OR peaktech OR 5600 OR 2 OR m OR flexible"

The PeakTech 1265 is an affordable 30 MHz 2-channel digital storage oscilloscope with a high-resolution TFT color display and extensive additional functions. It has a sampling rate of up to 250 MS/s and convinces with its high quality and easy handling with the best price/performance ratio. To quickly display each incoming waveform, simply press the Autoset key and the oscilloscope itself searches for the best possible display. With Autoscale, however, the scaling of the time base can be adjusted in a user-friendly manner. This oscilloscope has a VGA output for displaying the oscilloscope display on an external monitor or projector. Features 2-channel oscilloscope with 30 MHz analog bandwidth at max. 250 MS/s sampling rate 8 inch (20 cm) TFT color display with 800 x 600 pixels LAN, USB host, USB device & VGA interface Autoset function for user-friendly operation Recording length of max. 10,000 points Automatic measurement modes, XY mode and FFT function Specifications Bandwidth 30 MHz Channels 2 Screen size (TFT) 8' (20 cm) Resolution 800 x 600 Pixel Display Type Color-TFT Sampling 1 CH 250 MS/s Sampling 2 CH 125 MS/s Hor. scale max. 100 s/div Hor. scale min. 5 ns/div Memory depth 10,000 Points Rise Time < 14 ns Vert. resolution 8 Bit Vert. scale max. 10 V/div Vert. scale min. 2 mV/div Interfaces 1x USB, 1x LAN, 1x VGA Mains voltage 110/240 V AC; 50/60 Hz Included PeakTech 1265 Oscilloscope USB cable Software CD for Windows Power cord 2 probes BNC cable Carrying case Manual Downloads Software Datasheet_DE-EN Datasheet_FR Datasheet_IT Datasheet_ES

Read more less

The PeakTech 1094 two-pole voltage tester is a reliable and practical tool for measuring voltages up to 400 V. It uses LED indicators to display voltage levels at 12 V, 24 V, 50 V, 120 V, 240 V, and 400 V. The device supports both AC and DC voltage measurements and automatically detects and displays polarity when measuring DC voltages – no manual switching between AC and DC is required. This tester operates without batteries, ensuring it is always ready for use, even after extended periods of inactivity. With its IP54 protection rating, the PeakTech 1094 is robust and resistant to dust and splashing water, making it suitable for use in both indoor and outdoor environments. Specifications DC Voltage (max.) 400 V AC Voltage (max.) 400 V Over voltage category CAT III 400 V Accuracy -30% to 0% of the measured value Voltage test Automatically Polarity check Entire measuring range Range selection Automatically Response time <0.1s AC Voltage frequency range 50/60 Hz Dimensions 223 x 40 x 32 mm Weight 95 g Downloads Manual

Read more less

The Raspberry Pi M.2 HAT+ enables you to connect M.2 peripherals such as NVMe drives and AI accelerators to Raspberry Pi 5’s PCIe 2.0 interface, supporting fast (up to 500 MB/s) data transfer to and from NVMe drives and other PCIe accessories. Raspberry Pi M.2 HAT+ supports devices that have the M.2 M key edge connector, in the 2230 and 2242 form factors. It is capable of supplying up to 3 A to connected M.2 devices. Features Supports single-lane PCIe 2.0 interface (500 MB/s peak transfer rate) Supports devices that use the M.2 M key edge connector Supports devices with the 2230 or 2242 form factor Capable of supplying up to 3 A to connected M.2 devices Power and activity LEDs Included 1x Raspberry Pi 5 M.2 HAT+ 1x Ribbon cable 1x GPIO stacking header 4x Spacers 8x Screws Downloads Datasheet Schematics Assembly instructions

Read more less

The FR01D (2-in-1) thermal imaging camera and multimeter is a compact and lightweight solution that simplifies diagnostic and maintenance tasks. The one-click function allows you to switch effortlessly between thermal imaging and multimeter mode, giving you two important tools in one portable device. The multimeter is capable of measuring DC and AC voltage, resistance, diode checks, continuity testing, and capacitance. The FR01D has a 2.8-inch touchscreen with a resolution of 320 x 480 pixels. The device is powered by an integrated rechargeable lithium battery and can be charged via USB. With the FR01D, you can inspect and maintain circuit boards, check power supplies, repair electronic devices, and overhaul household appliances. Its compact size, multifunctionality, and user-friendliness make the FR01D the ideal companion for electronics and maintenance technicians. General Specifications Display size 2.8" (320 x 480) Touchscreen Resistive Data transmission USB-C Image storage format BMP Battery Li-ion battery Storage temperature −20°C～60°C（−4°F～140°F) Operating temperature 0°C～50°C（32°F～122°F) Operating humidity <85% RH Dimensions 134 x 69 x 25 mm Weight 130 g Thermal Imaging Specifications Sensor Vanadium oxide (VOx) Image capture frequency 25 Hz Thermal imaging pixels 192 x 192 Field of View (FOV) 50.0°(H) x 50°(V) / 72.1°(D) Temperature range −20°C ~ +550°C (−4°F～1022°F) Gain mode Auto Accuracy ±2°C or ±2% Measurement resolution 0.1°C / 0.1°F Multimeter Specifications DC input voltage (max.) 1000 V AC input voltage (max.) 750 V Resistance (max.) 99.99 MΩ Capacitance (max.) 99.99 mF Duty cycle test range 0.1% ~ 99.9% Diode test range 0 V ~ 3 V Continuity test 999.9 Ω Display 9999 counts (Refreshes 3x per second) Accuracy Function Range Resolution Accuracy AC Voltage 400 mV 0.1 mV 2% +3 9.999 V 0.001 V 1.0% +3 99.99 V 0.01 V 999.9 V 0.1V DC Voltage 400 mV 0.1 mV 2% +3 9.999 V 0.001 V 1.0% +3 99.99 V 0.01 V 999.9 V 0.1 V Resistance 999.9 Ω 0.1 Ω 0.5% +3 9.999 KΩ 0.001 kΩ 99.99 KΩ 0.01 kΩ 999.9 KΩ 0.1 kΩ 9.999 MΩ 0.001 MΩ 99.99 MΩ 0.01 MΩ 1.5% +3 Diode Test 3.000 V 0.001 V 10% Capacitance 9.999 nF 0.001 nF 2% +5 99.99 nF 0.01 nF 999.9 nF 0.1 nF 9.999 uF 0.001 uF 99.99 uF 0.01 uF 999.9 uF 0.1 uF 9.999 mF 0.001 mF 5% +5 99.99 mF 0.01 mF Included 1x FR01D IR-Camera and Multimeter 2x Test Leads 1x USB Cable 1x Manual

Read more less

39 Experiments with Raspberry Pi and Arduino This book is about Raspberry Pi 3 and Arduino camera projects. The book explains in simple terms and with tested and working example projects, how to configure and use a Raspberry Pi camera and USB based webcam in camera-based projects using a Raspberry Pi. Example projects are given to capture images, create timelapse photography, record video, use the camera and Raspberry Pi in security and surveillance applications, post images to Twitter, record wildlife, stream live video to YouTube, use a night camera, send pictures to smartphones, face and eye detection, colour and shape recognition, number plate recognition, barcode recognition and many more. Installation and use of popular image processing libraries and software including OpenCV, SimpleCV, and OpenALPR are explained in detail using a Raspberry Pi. The book also explains in detail how to use a camera on an Arduino development board to capture images and then save them on a microSD card. All projects given in this book have been fully tested and are working. Program listings for all Raspberry Pi and Arduino projects used in this book are available for download on the Elektor website.

Read more less

This PCIe to M.2 adapter is specifically designed for the Raspberry Pi 5. It supports the NVMe protocol for M.2 SSDs, enabling fast read and write operations, and adheres to the HAT+ standard. The adapter is compatible with M.2 SSDs in the 2230 and 2242 sizes. Included 1x PCIe to M.2 HAT+ Adapter 1x 2x20 Pin header 1x 16P cable (40 mm) 1x Standoff pack Downloads Wiki

Read more less

The Waveshare PoE M.2 HAT+ (B) combines Power over Ethernet (PoE) and PCIe-to-M.2 functionality for the Raspberry Pi 5. It supports the IEEE 802.3af/at networking standards and accommodates M.2 NVMe SSDs in 2230, 2242, 2260, and 2280 form factors. Additionally, it enables SSD boot for the Raspberry Pi. Features Standard Raspberry Pi 40-pin GPIO extension header, compatible with Raspberry Pi 5 Supports Power over Ethernet (PoE) and complies with the IEEE 802.3af/at network standards Utilizes a fully isolated Switch Mode Power Supply (SMPS) for stable power delivery Supports NVMe protocol M.2 interface hard drives, offering high-speed read/write performance and high efficiency Provides 1x PCIe in Gen2 or Gen3 mode Specifically designed for the Raspberry Pi 5 only Compatible with M.2 SSDs in 2230, 2242, 2260, and 2280 form factors Specifications PoE power input 37~57 V DC Power output GPIO header: 5 V/4.5 A (max.)2P header: 12 V/2 A (max.) Network standard IEEE 802.3af/at PoE Dimensions 56 x 85 mm Included 1x Waveshare PoE M.2 HAT+ (B) 1x 16-Pin PCIe cable 1x SSD mounting screw 1x Screws pack Downloads Wiki

Read more less

Raspberry Pi Camera Module 3 is a compact camera from Raspberry Pi. It offers an IMX708 12-megapixel sensor with HDR, and features phase detection autofocus. Camera Module 3 is available in standard and wide-angle variants, both of which are available with or without an infrared cut filter. Camera Module 3 can be used to take full HD video as well as stills photographs, and features an HDR mode up to 3 megapixels. Its operation is fully supported by the libcamera library, including Camera Module 3’s rapid autofocus feature: this makes it easy for beginners to use, while offering plenty for advanced users. Camera Module 3 is compatible with all Raspberry Pi computers. All variants of Raspberry Pi Camera Module 3 feature: Back-illuminated and stacked CMOS 12-megapixel image sensor (Sony IMX708) High signal-to-noise ratio (SNR) Built-in 2D Dynamic Defect Pixel Correction (DPC) Phase Detection Autofocus (PDAF) for rapid autofocus QBC Re-mosaic function HDR mode (up to 3 megapixel output) CSI-2 serial data output 2-wire serial communication (supports I²C fast mode and fast-mode plus) 2-wire serial control of focus mechanism Specifications Sensor Sony IMX708 Resolution 11.9 MP Sensor size 7.4 mm sensor diagonal Pixel size 1.4 x 1.4 µm Horizontal/vertical 4608 x 2592 pixels Common video modes 1080p50, 720p100, 480p120 Output RAW10 IR cut filter Integrated in standard variants; not present in NoIR variants Autofocus system Phase Detection Autofocus Ribbon cable length 200 mm Cable connector 15 x 1 mm FPC Dimensions 25 x 24 x 11.5 mm (12.4 mm height for Wide variants) Variants of Raspberry Pi Camera Module 3 Camera Module 3 Camera Module 3 NoIR Camera Module 3 Wide Camera Module 3 Wide NoIR Focus range 10 cm - ∞ 10 cm - ∞ 5 cm - ∞ 5 cm - ∞ Focal length 4.74 mm 4.74 mm 2.75 mm 2.75 mm Diagonal field of view 75 degrees 75 degrees 120 degrees 120 degrees Horizontal field of view 66 degrees 66 degrees 102 degrees 102 degrees Vertical field of view 41 degrees 41 degrees 67 degrees 67 degrees Focal ratio (F-stop) F1.8 F1.8 F2.2 F2.2 Infrared-sensitive No Yes No Yes Downloads GitHub Documentation

Read more less

The Raspberry Pi Global Shutter Camera is a specialised 1.6 MP camera from Raspberry Pi that is able to capture rapid motion without introducing artefacts typical of rolling shutter cameras. It is ideally suited to fast motion photography and to machine vision applications, where even small amounts of distortion can seriously degrade inference performance. With a large pixel size of 3.45 x 3.45 μm providing high light sensitivity, the Global Shutter Camera can operate with short exposure times (as low as 30 μs with adequate lighting), an advantage for high-speed photography. It features a 1.6 MP Sony IMX296 sensor, and it has the same C/CS-mount lens assembly as the Raspberry Pi High Quality Camera, for compatibility with the same broad variety of lenses. In common with other global shutter sensors, the IMX296 has a lower resolution than similarly sized rolling shutter sensors; a low pixel count is appropriate for machine vision applications, where high-resolution images are challenging to process in real time. The Global Shutter Camera's lower resolution means that with appropriate lens magnification, an image suitable for processing by a machine vision model can be captured natively. The Raspberry Pi Global Shutter Camera is compatible with any Raspberry Pi computer that has a CSI connector. Specifications Form factor 38 x 38 x 19.8 mm (29.5 mm adapter and dust cap) Weight 34 g (41 g with adapter and dust cap) Sensor Sony IMX296LQR-C Resolution 1.58 MP (color) Sensor size 6.3 mm (sensor diagonal) Pixel size 3.45 x 3.45 μm Output RAW10 Back focus length of lens Adjustable (12.5-22.4 mm) Lens standards CS-MountC-Mount (C-CS adapter included) IR cut filter Integrated Ribbon cable length 150 mm Included accessories C-CS mount adapterScrewdriver Tripod mount 1/4”-20 Included Raspberry Pi Global Shutter Camera C-CS mount adapter Screwdriver Ribbon cable (150 mm) Downloads Datasheet

Read more less

This NVMe M.2 2242 SSD (128 GB) is already pre-installed with Raspberry Pi OS for immediate use with the Raspberry Pi 5 M.2 HAT+. Features Form factor: M.2 2242 M-Key NVMe SSD Pre-loaded with Raspberry Pi OS High level of ability to endure shock, vibration, and high temperature SMART TRIM support PCIe Interface: PCIe Gen3 x2 Compliance: NVMe 1.3, PCI Express Base 3.1 Capacity: 128 GB Speed: Read: Up to 1700 MB/s Write: Up to 600 MB/s Shock: 1500 G/0.5 ms Operation temperature: 0°C-70°C Up to 30x faster than a typical hard disk drive Boosts burst write performance, making it ideal for typical computer workloads Faster boot-up, shutdown, application load, and response for Raspberry Pi Downloads Datasheet

Read more less

This PCIe 3.0 to dual M.2 HAT enables the Raspberry Pi 5 to access two NVMe SSDs, Hailo-8/8L (M.2 key B+M only), and Google Coral AI accelerators at PCIe 3.0 speeds. Features Dual M.2 Slots with PCIe 3.0 Speed: Utilizes the ASMedia ASM2806 PCIe 3.0 switch chip to ensure optimal performance, overcoming the limitations of PCIe 2.0. Stable Power Supply: Additional pogo pins provide extra power to ensure a stable high-speed connection. Multiple Size Support: Compatible with M.2 standard sizes 2230, 2242, 2260, and 2280. Back-mounted Design: Keeps the 40-pin GPIO free for use, allowing compatibility with other Raspberry Pi HATs. User-friendly Design: The S-shaped FPC cable does not obstruct the microSD card slot. Open Source Case: Seeed’s M.2 HATs are not compatible with the official Raspberry Pi case, but an adapted 3D-printable case (STP file) is provided. Applications Simultaneously supports AI acceleration and high-speed SSD storage Connects dual NVMe SSDs for large storage capacity Booting a Raspberry Pi from the SSD Specifications M.2 Slots 2 Max. PCIe Speed PCIe Gen3.0 PCIe Switch Chip ASM2806 M.2 Size Support 2280/2260/2242/2230 Max. Power Supply 5 V/3 A (max 3A: Pogo pin 2A + PCIe connector 1A) Cable FPC Assembly Method Back installation Dimensions 87 x 55 x 10 mm Included 1x Seeed Studio PCIe 3.0 to Dual M.2 HAT for Raspberry Pi 5 2x FPC cables (50 mm) 1x Screws & stud pack Downloads Wiki

Read more less