Search results for "peaktech OR 3442 OR true OR rms OR digital OR multimeter OR with OR bluetooth OR 60000 OR counts"

The PeakTech 1265 is an affordable 30 MHz 2-channel digital storage oscilloscope with a high-resolution TFT color display and extensive additional functions. It has a sampling rate of up to 250 MS/s and convinces with its high quality and easy handling with the best price/performance ratio. To quickly display each incoming waveform, simply press the Autoset key and the oscilloscope itself searches for the best possible display. With Autoscale, however, the scaling of the time base can be adjusted in a user-friendly manner. This oscilloscope has a VGA output for displaying the oscilloscope display on an external monitor or projector. Features 2-channel oscilloscope with 30 MHz analog bandwidth at max. 250 MS/s sampling rate 8 inch (20 cm) TFT color display with 800 x 600 pixels LAN, USB host, USB device & VGA interface Autoset function for user-friendly operation Recording length of max. 10,000 points Automatic measurement modes, XY mode and FFT function Specifications Bandwidth 30 MHz Channels 2 Screen size (TFT) 8' (20 cm) Resolution 800 x 600 Pixel Display Type Color-TFT Sampling 1 CH 250 MS/s Sampling 2 CH 125 MS/s Hor. scale max. 100 s/div Hor. scale min. 5 ns/div Memory depth 10,000 Points Rise Time < 14 ns Vert. resolution 8 Bit Vert. scale max. 10 V/div Vert. scale min. 2 mV/div Interfaces 1x USB, 1x LAN, 1x VGA Mains voltage 110/240 V AC; 50/60 Hz Included PeakTech 1265 Oscilloscope USB cable Software CD for Windows Power cord 2 probes BNC cable Carrying case Manual Downloads Software Datasheet_DE-EN Datasheet_FR Datasheet_IT Datasheet_ES

Read more less

The PeakTech 1094 two-pole voltage tester is a reliable and practical tool for measuring voltages up to 400 V. It uses LED indicators to display voltage levels at 12 V, 24 V, 50 V, 120 V, 240 V, and 400 V. The device supports both AC and DC voltage measurements and automatically detects and displays polarity when measuring DC voltages – no manual switching between AC and DC is required. This tester operates without batteries, ensuring it is always ready for use, even after extended periods of inactivity. With its IP54 protection rating, the PeakTech 1094 is robust and resistant to dust and splashing water, making it suitable for use in both indoor and outdoor environments. Specifications DC Voltage (max.) 400 V AC Voltage (max.) 400 V Over voltage category CAT III 400 V Accuracy -30% to 0% of the measured value Voltage test Automatically Polarity check Entire measuring range Range selection Automatically Response time <0.1s AC Voltage frequency range 50/60 Hz Dimensions 223 x 40 x 32 mm Weight 95 g Downloads Manual

Read more less

The FR01D (2-in-1) thermal imaging camera and multimeter is a compact and lightweight solution that simplifies diagnostic and maintenance tasks. The one-click function allows you to switch effortlessly between thermal imaging and multimeter mode, giving you two important tools in one portable device. The multimeter is capable of measuring DC and AC voltage, resistance, diode checks, continuity testing, and capacitance. The FR01D has a 2.8-inch touchscreen with a resolution of 320 x 480 pixels. The device is powered by an integrated rechargeable lithium battery and can be charged via USB. With the FR01D, you can inspect and maintain circuit boards, check power supplies, repair electronic devices, and overhaul household appliances. Its compact size, multifunctionality, and user-friendliness make the FR01D the ideal companion for electronics and maintenance technicians. General Specifications Display size 2.8" (320 x 480) Touchscreen Resistive Data transmission USB-C Image storage format BMP Battery Li-ion battery Storage temperature −20°C～60°C（−4°F～140°F) Operating temperature 0°C～50°C（32°F～122°F) Operating humidity <85% RH Dimensions 134 x 69 x 25 mm Weight 130 g Thermal Imaging Specifications Sensor Vanadium oxide (VOx) Image capture frequency 25 Hz Thermal imaging pixels 192 x 192 Field of View (FOV) 50.0°(H) x 50°(V) / 72.1°(D) Temperature range −20°C ~ +550°C (−4°F～1022°F) Gain mode Auto Accuracy ±2°C or ±2% Measurement resolution 0.1°C / 0.1°F Multimeter Specifications DC input voltage (max.) 1000 V AC input voltage (max.) 750 V Resistance (max.) 99.99 MΩ Capacitance (max.) 99.99 mF Duty cycle test range 0.1% ~ 99.9% Diode test range 0 V ~ 3 V Continuity test 999.9 Ω Display 9999 counts (Refreshes 3x per second) Accuracy Function Range Resolution Accuracy AC Voltage 400 mV 0.1 mV 2% +3 9.999 V 0.001 V 1.0% +3 99.99 V 0.01 V 999.9 V 0.1V DC Voltage 400 mV 0.1 mV 2% +3 9.999 V 0.001 V 1.0% +3 99.99 V 0.01 V 999.9 V 0.1 V Resistance 999.9 Ω 0.1 Ω 0.5% +3 9.999 KΩ 0.001 kΩ 99.99 KΩ 0.01 kΩ 999.9 KΩ 0.1 kΩ 9.999 MΩ 0.001 MΩ 99.99 MΩ 0.01 MΩ 1.5% +3 Diode Test 3.000 V 0.001 V 10% Capacitance 9.999 nF 0.001 nF 2% +5 99.99 nF 0.01 nF 999.9 nF 0.1 nF 9.999 uF 0.001 uF 99.99 uF 0.01 uF 999.9 uF 0.1 uF 9.999 mF 0.001 mF 5% +5 99.99 mF 0.01 mF Included 1x FR01D IR-Camera and Multimeter 2x Test Leads 1x USB Cable 1x Manual

Read more less

Bluno is the first of its kind in integrating Bluetooth 4.0 (BLE) module into Arduino Uno, making it an ideal prototyping platform for both software and hardware developers to go BLE. You will be able to develop your own smart bracelet, smart pedometer, and more. Through the low-power Bluetooth 4.0 technology, real-time low energy communication can be made really easy. Bluno integrates a TI CC2540 BT 4.0 chip with the Arduino UNno. It allows wireless programming via BLE, supports Bluetooth HID, AT command to config BLE and you can upgrade BLE firmware easily. Bluno is also compatible with all 'Arduino Uno' pins which means any project made with Uno can directly go wireless! Specifications On-board BLE chip: TI CC2540 Wireless Programming via BLE Support Bluetooth HID Support AT command to config the BLE Transparent communication through Serial Upgrade BLE firmware easily DC Supply: USB Powered or External 7~12 V DC Microcontroller: Atmega328 Bootloader: Arduino Uno ( disconnect any BLE device before uploading a new sketch ) Compatible with the Arduino Uno pin mapping Size: 60 x 53 mm(2.36 x 2.08') Weight: 30 g

Read more less

The field of digital electronics is central to modern technology. This e-book presents fundamental circuits using gates, flip-flops and counters from the CMOS 4000 Series. Each of the 50 experiments has a circuit diagram as well as a detailed illustration of the circuit’s construction on solderless breadboard. Learning these fundamentals is best done using practical experiments. Building these digital circuits will improve your knowledge and will be fun to boot. Many of the circuits presented here have practical real-life applications. With a good overview of the field, you’ll be well equipped to find simple and cost-effective solutions for any application. The e-book is targeted essentially at students, trainees and anyone with an interest in and requiring an introduction to digital control electronics. Moreover, the knowledge gleaned here is the foundation for further projects in the field of microcontrollers and programming.

Read more less

For Raspberry Pi, ESP32 and nRF52 with Python, Arduino and Zephyr Bluetooth Low Energy (BLE) radio chips are ubiquitous from Raspberry Pi to light bulbs. BLE is an elaborate technology with a comprehensive specification, but the basics are quite accessible. A progressive and systematic approach will lead you far in mastering this wireless communication technique, which is essential for working in low power scenarios. In this book, you’ll learn how to: Discover BLE devices in the neighborhood by listening to their advertisements. Create your own BLE devices advertising data. Connect to BLE devices such as heart rate monitors and proximity reporters. Create secure connections to BLE devices with encryption and authentication. Understand BLE service and profile specifications and implement them. Reverse engineer a BLE device with a proprietary implementation and control it with your own software. Make your BLE devices use as little power as possible. This book shows you the ropes of BLE programming with Python and the Bleak library on a Raspberry Pi or PC, with C++ and NimBLE-Arduino on Espressif’s ESP32 development boards, and with C on one of the development boards supported by the Zephyr real-time operating system, such as Nordic Semiconductor's nRF52 boards. Starting with a very little amount of theory, you’ll develop code right from the beginning. After you’ve completed this book, you’ll know enough to create your own BLE applications.

Read more less

For Raspberry Pi, ESP32 and nRF52 with Python, Arduino and Zephyr Bluetooth Low Energy (BLE) radio chips are ubiquitous from Raspberry Pi to light bulbs. BLE is an elaborate technology with a comprehensive specification, but the basics are quite accessible. A progressive and systematic approach will lead you far in mastering this wireless communication technique, which is essential for working in low power scenarios. In this book, you’ll learn how to: Discover BLE devices in the neighborhood by listening to their advertisements. Create your own BLE devices advertising data. Connect to BLE devices such as heart rate monitors and proximity reporters. Create secure connections to BLE devices with encryption and authentication. Understand BLE service and profile specifications and implement them. Reverse engineer a BLE device with a proprietary implementation and control it with your own software. Make your BLE devices use as little power as possible. This book shows you the ropes of BLE programming with Python and the Bleak library on a Raspberry Pi or PC, with C++ and NimBLE-Arduino on Espressif’s ESP32 development boards, and with C on one of the development boards supported by the Zephyr real-time operating system, such as Nordic Semiconductor's nRF52 boards. Starting with a very little amount of theory, you’ll develop code right from the beginning. After you’ve completed this book, you’ll know enough to create your own BLE applications.

Read more less

MDP-M01 is a display control module equipped with a 2.8-inch TFT display screen, the screen can be turned 90 degrees, which is convenient for users to view data and waveform. MDP-M01 can realize online display and control with MDP-P906 mini digital power supply modules and other modules of MDP system through 2.4 GHz wireless communication, and can control up to 6 sub-modules at the same time. Specifications Screen size 2.8' TFT Screen resolution 240 x 320 Power Micro USB power input, or taking power from sub-module via dedicated power cable Input DC 5 V/0.3 A Other functions Can control up to 6 sub-modulesUpgrade formware through Micro USB Dimensions 107 x 66 x 13.6 mm Weight 133 g Included 1x MDP-M01 Smart Digital Monitor 1x Cable (2.5 mm jack to Micro USB) Downloads User Manual v3.4 Firmware v1.32

Read more less