Search results for "eprom"
MonkMakes Electronics Notebook
Specifications A4 (210 x 297 mm) squared-grid spiral-bound notebook with watermark breadboards 158 pages, card covers. The book also includes Microcontroller programming cheat sheet Common circuits and calculations Pinouts Resistor color codes ASCII table
€ 16,95
Members € 15,26
Diamex Diamex EXA-Prog Package
EXA-Prog in housing EXA-Prog represents the new generation of ISP programmers, which are not limited to one specific microcontroller type, but support several different controller architectures and programming interfaces. Laser-cut plexiglass housing. Two built-in status LEDs signal the current state of the programmer. Features Function selection via DIP switch Signal level switchable, 3.3 V, 5 V Integrated high voltage generator for UPDI programming Automatic bit-rate adjustment in AVR-ISP mode Clock generator for AVR controller with fuse oscillator Button to reset the connected microcontroller 10-pin standard ISP connector Optional accessories: 10-pin to 6-pin adapter, ESP01 adapter Mini-USB connector for power supply and connection to PC Firmware can be updated via USB Windows PC tool for testing the signal levels at the programming port. Current consumption without microcontroller connected: approx. 30 mA Signal level at programming connector: 5 V (USB voltage) or 3.3 V Power supply for the external circuit: max. 300 mA (3.3 V), max. 500 mA (5 V) UPDI high voltage: approx. 12.3 V Weight: approx. 25 g Adapter 10-pin to 6-pin IS P and 6-pin UPDI The optimal solution for in-system programming (ISP) of AVR controllers. There are two different standards for the AVR-ISP interface, 6-pin and 10-pin. With this adapter kit, you can exchange the programming lines between both standards. For programming AVR-UPDI a 6-pin connector is also needed. This adapter supports 10-pin to 6-pin for AVR-ISP programming and 10-pin to 6-pin for AVR-UPDI programming. ESP adapter No buttons or switches are needed to activate the ESP bootloader. When ESPTOOL is used, the bootloader is automatically activated and the firmware is started after programming is complete. If another program is used that does not take over this control itself, the bootloader of the ESP can also be activated by a long press on the RESET button of the EXA-PROG and the firmware can be started by a short press after programming. AVR swivel lever High-quality module with swivel lever zero force socket for almost all AVR controllers in DIL package. No own board is required. DIL controllers are easy and fast to program. Can also be used for series production. The 10-pin ISP standard connector from Atmel is used. Additionally, pin 3 is designed as a clock connector if the controller is set to an external clock. 5x 10-pin ISP well connectors for AVR controller in DIL package Compatible with all signal levels Pin 3 for the clock generator High quality swing lever socket (zero force socket) for variable 4-18 mm pin spacing Included EXA-Prog in housing Adapter 10-pin to 6-pin ISP and 6-pin UPDI ESP adapter AVR swivel lever Mini-USB cable 10-pin connection cable 6-pin connection cable 6-pin jumper cable, male-female 6-pin jumper cable, female-female
€ 74,95€ 64,95
Members identical
Pimoroni Pimoroni Breakout Garden for Raspberry Pi (I²C)
Thanks to its six sturdy slots, Breakout Garden enables the users to simply plug and play with various tiny breakout board.Just insert one or more boards into the slots in the Breakout Garden HAT and you’re ready to go. The mini breakouts feel secure enough in the edge-connector slots and are very unlikely to fall out.There are a number of useful pins along the top of Breakout Garden, which lets you connect other devices and integrate them into your project.You shouldn't be worried if you insert a board the wrong way thanks to provided reverse polarity protection. It doesn't matter which slot you use for each breakout either, because the I²C address of the breakout will be recognised by the software and it'll detect them correctly in case you move them around.Features Six sturdy edge-connector slots for Pimoroni breakouts 0.1” pitch, 5 pin connectors Broken-out pins (1 × 10 strip of male header included) Standoffs (M2.5, 10 mm height) included to hold your Breakout Garden securely Reverse polarity protection (built into breakouts) HAT format board Compatible with Raspberry Pi 3 B+, 3, 2, B+, A+, Zero, and Zero W It's suggested using the included standoffs to attache Breakout Garden to your Raspberry Pi.SoftwareBreakout Garden doesn't require any software of its own, but each breakout you use will need a Python library. On the Breakout Garden GitHub page you'll find an automatic installer, which will install the appropriate software for a given breakout. There are also some examples that show you what else you can do with Breakout Garden.
€ 19,95
Members € 17,96
Elektor Classics Elektor Archive 1961-2023 (USB Stick) NL
6 Elektor decennia (jaren '60, '70, '80, '90, '2000 en '2010) op USB-stick Deze USB-stick (32 GB, USB 3.0) bevat de complete jaargangen 1961-2023 (alle nummers) van het elektronica-vakblad Elektor. Elektor wil mensen inspireren om zich elektronica en computertechniek eigen te maken door het presenteren van nabouwvriendelijke, professioneel ontworpen schakelingen op alle terreinen van de elektronica: Audio & Video Basiskennis Computer & apparatuur Hobby & modelbouw Hoogfrequent Huis & tuin Meten & testen Microcontrollers Stroomvoorziening Al dat andere dat niet zo gemakkelijk in een van deze categorieën kan worden ondergebracht. De meer dan 10.000 afzonderlijke artikelen zijn chronologisch op publicatiedatum (maand/jaar) geordend. Systeemeisen Computer geschikt voor Adobe Reader vanaf versie 7 Webbrowser
€ 199,95€ 99,95
Members identical
Espressif ESP32-C3-WROOM-02U-N4
ESP32-C3-WROOM-02U is a general-purpose Wi-Fi and Bluetooth LE module. The rich set of peripherals and high performance make the module an ideal choice for smart homes, industrial automation, health care, consumer electronics, etc. ESP32-C3-WROOM-02U features an external SPI flash and comes with a connector for an external antenna. ESP32-C3-WROOM-02U has an operating ambient temperature option of –40∼85°C, embedded with the ESP32-C3 chip. ESP32-C3 has a 32-bit RISC-V single-core processor. It integrates a rich set of peripherals, ranging from UART, I²C, I²S, remote control peripheral, LED PWM controller, general DMA controller, TWAI controller, USB Serial/JTAG controller, temperature sensor, ADC, etc. It also includes SPI, Dual SPI and Quad SPI interfaces. Features Flash: 4 MB (Quad SPI) Dimensions: 18.0 x 20.0 x 3.2 mm Downloads Datasheet
€ 7,95
Members € 7,16
Elektor Labs Elektor Raspberry Pi Buffer Board
When you experiment with the Raspberry Pi on a regular basis and you connect a variety of external hardware to the GPIO port via the header you may well have caused some damage in the past. The Raspberry Pi Buffer Board is there to prevent this! The board is compatible with Raspberry Pi Zero, 3, 4, 5 and 400. All 26 GPIOs are buffered with bi-directional voltage translators to protect the Raspberry Pi when experimenting with new circuits. The PCB is intended to be inserted in the back of Raspberry Pi< 400. The connector to connect to the Raspberry Pi is a right angled 40-way receptacle (2x20). The PCB is only a fraction wider. A 40-way flat cable with appropriate 2x20 headers can be connected to the buffer output header to experiment for instance with a circuit on a breadboard or PCB. The circuit uses four TXS0108E ICs by Texas Instruments. The PCB can also be put upright on a Raspberry Pi 3 or newer. Downloads Schematics Layout
€ 29,95€ 22,95
Members € 20,66
Evil Mad Science Hold-down Magnet and Clip Set for AxiDraw
The set of magnets and spring clips is designed for use with the AxiDraw magnetic easel boards for letter/A4 and tabloid/A3 sizes, but can be used with almost any magnetic surface. The set includes a pair of special spring clips with magnetic bases, as well as six skinny magnets for holding down paper. The two special spring clips each have two curved tines that apply gentle pressure to your paper. They allow you to slide paper directly in and out, quickly and easily, without touching any magnets, clips, or tape. They have a long reach to be positioned behind the rulers on our magnetic easels. Magnetic bases allow you to position them where needed. Two of these spring clips provide just enough pressure to keep a sheet of paper steady while you write or draw on it. This set also includes six cylindrical magnets, 4 mm in diameter and 10 mm tall, which are easy to position and firmly hold paper. The tall aspect ratio makes them particularly easy to grasp (unlike disc magnets). Perhaps more importantly, they tend to yield and tip over if hit by an errant pen tip, rather than holding so fast as to damage your pen or move your paper.
€ 17,95
Members € 16,16
Seeed Studio Seeed Studio Grove 10x Universal 4-pin Connector (2-mm Pitch)
The universal 4 Pin connector is a white 4-pin buckled connector used on Stem, Twigs and Grove cables. The pin spacing is 2 mm. There are 10 connectors per bag. They can be used in DIY projects.
€ 3,95
Members € 3,56
Espressif ESP32-S3-WROOM-1-N16R8
ESP32-S3-WROOM-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module that is built around the ESP32-S3 series of SoCs. On top of a rich set of peripherals, the acceleration for neural network computing and signal processing workloads provided by the SoC make the modules an ideal choice for a wide variety of application scenarios related to AI and Artificial Intelligence of Things (AIoT), such as wake word detection, speech commands recognition, face detection and recognition, smart home, smart appliances, smart control panel, smart speaker, etc. ESP32-S3-WROOM-1 comes with a PCB antenna. Features Module integrated: ESP32-S3-WROOM-1-N16R8 Flash: 16 MB (Quad SPI) PSRAM: 8 MB (Octal SPI) Downloads Datasheet