STEMlab 125-14 (Calibrated Diagnostic Kit)

  • BrandRed Pitaya

STEMlab 125-14 (originally Red Pitaya V1.1) is an open source measurement and control tool in size of a credit card (dimensions: 107 x 60 x 21 mm). It can replace many expensive laboratory measurement instruments. The STEMlab 125-14 unit is a network attached device based on Linux operating system. It includes Radio Frequency signal acquisition and generation technologies, FPGA, Digital Signal Processing and CPU processing. The STEMlab 125-14 unit is equipped with a Micro USB socket used for console connection, a microSD slot for microSD memory card, a RJ45 socket for Ethernet connection and a USB socket used for standard USB devices.

Features:
• High performance hardware at a surprising price tag.
• Replaces most essential instruments: (Oscilloscope, Spectrum analyser, Signal generator, LCR meter)
• LAN or wireless access from any WEB browser via tablet or a PC regardless of the OS (MAC, Linux, Windows, Android, iOS).
• LabView and MATLAB® interface.
• Possibility to make your own application and share it with others.
• Open source software.

RF inputs:
• Number of channels: 2
• Bandwidth: 50 MHz (3 dB)
• Sample rate: 125 Msps
• Input impedance: 1 MΩ / 10 pF
• Connector: SMA-F

RF outputs:
• Number of channels: 2
• Bandwidth: 50 MHz
• Sample rate: 125 Msps
• Load impedance: 50 Ω
• Connector: SMA-F

Auxiliary analog input channels:
• Number of channels: 4
• Nominal sampling rate: 100 ksps
• ADC resolution: 14 bit
• Input voltage range: 0 to +3.5 V
• Input coupling: DC
• Connector: IDC connector

Auxiliary analog output channels:
• Number of channels: 4
• Output type: Low pass filtered PWM
• PWM time resolution: 4ns (1/250 MHz)
• Output voltage range: 0 to +1.8 V

Dimensions: 107 x 60 x 21 mm

Calibration:
Calibration is performed in noise controlled environment. Inputs and outputs gains are calibrated with 0.02 % and 0.003 % DC reference voltage standards. Input gains calibration is performed in medium size timebase range. STEMlab 125-14 is non-shielded device and its inputs/outputs ground is not connected to the earth grounding as it is in case of classical Oscilloscopes. To achieve calibration results given below, STEMlab 125-14 must be grounded and shielded.

Inputs      
LV settings (+/- 1 V range)   LV settings (+/- 1 V range)  
DC gain accuracy @ 122 kS/s DC offset @ 122 kS/s DC gain accuracy @ 122 kS/s DC offset @ 122 kS/s
0.2 % +/- 0.5 mV 0.4 % +/- 2 mV
Outputs      
DC offset   DC gain accuracy Ripple @ 0.5V DC
+/- 4 mV   0.4 % 0.4 mVpp

Kit contents:
• 1x STEMlab 125-14 board with calibrated Inputs and Outputs
• 1x Aluminium case
• 1x micro USB power supply adaptor
• 1x microSD card (4 GB) with pre-installed OS
• 1x Ethernet cable (1 m)
• 2x Osciloscope probes
• 2x SMA to BCN adapter
• 2x 50 ohm termination
• 2x SMA T adapter
• 1x WIFI dongle

Product form

STEMlab 125-14 (originally Red Pitaya V1.1) is an open source measurement and control tool in size of a credit card... Read more

No reviews

2 in stock

€ 999,00€ 899,00 incl. VAT
Members identical

      Details

      SKU: 17941
      EAN: 017941

      STEMlab 125-14 (originally Red Pitaya V1.1) is an open source measurement and control tool in size of a credit card (dimensions: 107 x 60 x 21 mm). It can replace many expensive laboratory measurement instruments. The STEMlab 125-14 unit is a network attached device based on Linux operating system. It includes Radio Frequency signal acquisition and generation technologies, FPGA, Digital Signal Processing and CPU processing. The STEMlab 125-14 unit is equipped with a Micro USB socket used for console connection, a microSD slot for microSD memory card, a RJ45 socket for Ethernet connection and a USB socket used for standard USB devices.

      Features:
      • High performance hardware at a surprising price tag.
      • Replaces most essential instruments: (Oscilloscope, Spectrum analyser, Signal generator, LCR meter)
      • LAN or wireless access from any WEB browser via tablet or a PC regardless of the OS (MAC, Linux, Windows, Android, iOS).
      • LabView and MATLAB® interface.
      • Possibility to make your own application and share it with others.
      • Open source software.

      RF inputs:
      • Number of channels: 2
      • Bandwidth: 50 MHz (3 dB)
      • Sample rate: 125 Msps
      • Input impedance: 1 MΩ / 10 pF
      • Connector: SMA-F

      RF outputs:
      • Number of channels: 2
      • Bandwidth: 50 MHz
      • Sample rate: 125 Msps
      • Load impedance: 50 Ω
      • Connector: SMA-F

      Auxiliary analog input channels:
      • Number of channels: 4
      • Nominal sampling rate: 100 ksps
      • ADC resolution: 14 bit
      • Input voltage range: 0 to +3.5 V
      • Input coupling: DC
      • Connector: IDC connector

      Auxiliary analog output channels:
      • Number of channels: 4
      • Output type: Low pass filtered PWM
      • PWM time resolution: 4ns (1/250 MHz)
      • Output voltage range: 0 to +1.8 V

      Dimensions: 107 x 60 x 21 mm

      Calibration:
      Calibration is performed in noise controlled environment. Inputs and outputs gains are calibrated with 0.02 % and 0.003 % DC reference voltage standards. Input gains calibration is performed in medium size timebase range. STEMlab 125-14 is non-shielded device and its inputs/outputs ground is not connected to the earth grounding as it is in case of classical Oscilloscopes. To achieve calibration results given below, STEMlab 125-14 must be grounded and shielded.

      Inputs      
      LV settings (+/- 1 V range)   LV settings (+/- 1 V range)  
      DC gain accuracy @ 122 kS/s DC offset @ 122 kS/s DC gain accuracy @ 122 kS/s DC offset @ 122 kS/s
      0.2 % +/- 0.5 mV 0.4 % +/- 2 mV
      Outputs      
      DC offset   DC gain accuracy Ripple @ 0.5V DC
      +/- 4 mV   0.4 % 0.4 mVpp

      Kit contents:
      • 1x STEMlab 125-14 board with calibrated Inputs and Outputs
      • 1x Aluminium case
      • 1x micro USB power supply adaptor
      • 1x microSD card (4 GB) with pre-installed OS
      • 1x Ethernet cable (1 m)
      • 2x Osciloscope probes
      • 2x SMA to BCN adapter
      • 2x 50 ohm termination
      • 2x SMA T adapter
      • 1x WIFI dongle

      Recently viewed products

      Login

      Forgot password?

      Don't have an account yet?
      Create an account