Arduino Giga R1 WiFi

Description

The Arduino Giga R1 WiFi brings the power of the STM32H7 to the same form factor as the popular Mega and Due, being the first Mega board to include onboard Wi-Fi and Bluetooth connectivity.

The board provides 76 digital inputs/outputs (12 with PWM capability), 14 analog inputs and 2 analog outputs (DAC) all easily accessible via pin headers. The STM32 microprocessor with dual-core Cortex-M7 and Cortex-M4, together with onboard memory and audio jack enables you to perform machine learning and signal processing on the edge.

Microcontroller (STM32H747XI)

This dual core 32-bits microcontroller allows you have two brain talking to each other (a Cortex-M7 at 480 MHz and a Cortex-M4 at 240 MHz) you can even run micropython in one and Arduino in the other.

Wireless communication (Murata 1DX)

Whether you prefer Wi-Fi or Bluetooth, the Giga R1 WiFi got you covered. You can even quickly connect to the Arduino IoT Cloud and keep track of your project remotely. And if you are concerned about the security of the communication, the ATECC608A keeps everything under control.

Hardware ports and communication

Following the legacy of the Arduino Mega and the Arduino Due, the Giga R1 WiFi has 4x UARTs (hardware serial ports), 3x I²C ports (1 more than its predecessors), 2x SPI ports (1 more than its predecessors), 1x FDCAN.

GPIOs and extra pins

By keeping the same form factor of the Mega and the Due, you can easily adapt your custom made shields to the Giga R1 WiFi (remember this board works at 3.3 V though!). Also, additional headers have been added so that the total number of GPIO pins is now 76, and two new pins have been added: a VRTC so you can connect a battery to keep the RTC running while the board is off and an OFF pin so you can shut down the board.

Connectors

The Giga R1 WiFi has extra connectors on board which will facilitate the creation of your project without any extra hardware. This board has:

  • USB-A connector suitable for hosting USB sticks, other mass storage devices and HID devices such as keyboard or mouse.
  • 3.5 mm input-output jack connected to DAC0, DAC1 and A7.
  • USB-C to power and program the board, as well as simulate an HID device such as mouse or keyboard.
  • Jtag connector, 2x5 1.27 mm.
  • 20-pin Arducam camera connector.

Higher voltage support: In comparison with its predecessors that support up to 12 V, the Giga R1 WiFi can handle a range of 6 to 24 V.

Specifications

Microcontroller STM32H747XI dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet)
Radio Module Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth (datasheet)
Secure Element ATECC608A-MAHDA-T (datasheet)
USB USB-C Programming Port / HID
USB-A Host (enable with PA_15)
Pins Digital I/O pins 76
Analog input pins 12
DAC 2 (DAC0/DAC1)
PWM pins 12
Misc VRT & OFF pin
Communication UART 4x
I²C 3x
SPI 2x
CAN Yes (requires an external transceiver)
Connectors Camera I²C + D54-D67
Display D1N, D0N, D1P, D0P, CKN, CKP + D68-D75
Audio Jack DAC0, DAC1, A7
Power Circuit operating voltage 3.3 V
Input voltage (VIN) 6-24 V
DC Current per I/O Pin 8 mA
Clock Speed Cortex-M7 480 MHz
Cortex-M4 240 MHz
Memory STM32H747XI 2 MB Flash, 1 MB RAM
Dimensions 53 x 101 mm

Downloads

Product form

The Arduino Giga R1 WiFi brings the power of the STM32H7 to the same form factor as the popular Mega... Read more

€ 89,95 incl. VAT
Members € 80,96

    • Ship today? Order within May 28, 2024 17:00:00 +0200

    Details

    SKU: 20436
    EAN: 7630049203266

    Description

    The Arduino Giga R1 WiFi brings the power of the STM32H7 to the same form factor as the popular Mega and Due, being the first Mega board to include onboard Wi-Fi and Bluetooth connectivity.

    The board provides 76 digital inputs/outputs (12 with PWM capability), 14 analog inputs and 2 analog outputs (DAC) all easily accessible via pin headers. The STM32 microprocessor with dual-core Cortex-M7 and Cortex-M4, together with onboard memory and audio jack enables you to perform machine learning and signal processing on the edge.

    Microcontroller (STM32H747XI)

    This dual core 32-bits microcontroller allows you have two brain talking to each other (a Cortex-M7 at 480 MHz and a Cortex-M4 at 240 MHz) you can even run micropython in one and Arduino in the other.

    Wireless communication (Murata 1DX)

    Whether you prefer Wi-Fi or Bluetooth, the Giga R1 WiFi got you covered. You can even quickly connect to the Arduino IoT Cloud and keep track of your project remotely. And if you are concerned about the security of the communication, the ATECC608A keeps everything under control.

    Hardware ports and communication

    Following the legacy of the Arduino Mega and the Arduino Due, the Giga R1 WiFi has 4x UARTs (hardware serial ports), 3x I²C ports (1 more than its predecessors), 2x SPI ports (1 more than its predecessors), 1x FDCAN.

    GPIOs and extra pins

    By keeping the same form factor of the Mega and the Due, you can easily adapt your custom made shields to the Giga R1 WiFi (remember this board works at 3.3 V though!). Also, additional headers have been added so that the total number of GPIO pins is now 76, and two new pins have been added: a VRTC so you can connect a battery to keep the RTC running while the board is off and an OFF pin so you can shut down the board.

    Connectors

    The Giga R1 WiFi has extra connectors on board which will facilitate the creation of your project without any extra hardware. This board has:

    • USB-A connector suitable for hosting USB sticks, other mass storage devices and HID devices such as keyboard or mouse.
    • 3.5 mm input-output jack connected to DAC0, DAC1 and A7.
    • USB-C to power and program the board, as well as simulate an HID device such as mouse or keyboard.
    • Jtag connector, 2x5 1.27 mm.
    • 20-pin Arducam camera connector.

    Higher voltage support: In comparison with its predecessors that support up to 12 V, the Giga R1 WiFi can handle a range of 6 to 24 V.

    Specifications

    Microcontroller STM32H747XI dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet)
    Radio Module Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth (datasheet)
    Secure Element ATECC608A-MAHDA-T (datasheet)
    USB USB-C Programming Port / HID
    USB-A Host (enable with PA_15)
    Pins Digital I/O pins 76
    Analog input pins 12
    DAC 2 (DAC0/DAC1)
    PWM pins 12
    Misc VRT & OFF pin
    Communication UART 4x
    I²C 3x
    SPI 2x
    CAN Yes (requires an external transceiver)
    Connectors Camera I²C + D54-D67
    Display D1N, D0N, D1P, D0P, CKN, CKP + D68-D75
    Audio Jack DAC0, DAC1, A7
    Power Circuit operating voltage 3.3 V
    Input voltage (VIN) 6-24 V
    DC Current per I/O Pin 8 mA
    Clock Speed Cortex-M7 480 MHz
    Cortex-M4 240 MHz
    Memory STM32H747XI 2 MB Flash, 1 MB RAM
    Dimensions 53 x 101 mm

    Downloads

    Customer Reviews

    Based on 1 review
    100%
    (1)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    S
    Sebastian
    Great device, highly suitable for audio DSP experiments

    I received the Arduino GIGA R1 WiFi last week and immediately went on to implement an audio loopback-device using the on-board ADCs / DACs. IT works extremely well and I am quite excited for future DSP-experiments.

    Recently viewed products

    Login

    Forgot password?

    Don't have an account yet?
    Create an account