46912376930636 0.96" OLED Display (Blue, I²C, 4-Pin) Kuongshun Trade Bestsellers > Components > Displays & LEDs 018747 0.96' (24 mm) monochrome graphical OLED display with a resolution of 128 x 32 pixels mounted on a 28 x 28 mm PCB. The effective display surface is 11 x 23 mm. It has a 4-pin connector to be used with an I²C bus (with SCL & SDA signals). The display works with 5 V and 3.3 V applications. Specifications Size: 0.96 inch / 24 mm Resolution: 128 x 32 pixels Board size: 28 x 28 mm Effective display surface: 11 x 23 mm Visual Angle: > 160 ° Input Voltage: 3.3 V ~ 6 V Wide voltage support: 3.3 V, 5 V Viewing angle: > 160 Drive IC: SSD1306 Operating temperature: -30 °C to 80 °C I²C Signals: SCL, SDA I²C address: 0x78 (or 0x3c, default) or 0x7a (or 0x3d). Note: I²C addresses can (unfortunately) be specified in two ways: including R/W bit or not. Therefore 0x78 (0x7a) including the R/W bit is equal to 0x3c (0x3d) without R/W bit. OLED Advantages Smaller volume Ultra-low power consumption High Contrast Display dot self-luminous Wide voltage support Warning: The display’s glass is fragile, please be careful while handling it. If the glass is broken, the screen will not work well. https://www.elektor.com/cdn/shop/files/18747_-_overview-1_1_1.jpg?v=1689238409https://www.elektor.com/cdn/shop/files/18747_-_bottom_view_1_1.jpg?v=1693837881https://www.elektor.com/products/0-96-oled-display-blue-i2c-4-pin?variant=46912376930636 in stock 9.95 26 4.9 6.9 2 - 4 Werktage 46907288453452 0.96" OLED Display for Arduino (128x64) Kuongshun Trade Arduino > Arduino Accessories > Components > Displays & LEDs 018004 Specifications Size: 0.96 inch Resolution: 128 x 64 Visual Angle: >160 ° Input Voltage: 3.3 V ~ 6 V Wide voltage support: 3.3 V, 5 V Viewing angle: >160 Only Need 2 I/O Port to Control Drive IC: SSD1306 Operating temperature: -30 °C to 80 °C OLED Advantages Smaller volume Ultra-low power consumption High contrast Display dot self-luminous Broad voltage support Independent communication method via SPI or IIC 128x64 Dot matrix Broad visual angle: maximum visual angle 160° Industrial-grade operating temperature: -30 ~ 70 °C Warning: The display’s glass is very thin, please be careful while using it. If The glass is broken, display will not work well. https://www.elektor.com/cdn/shop/files/lcdisplay-smalla-web_2.jpg?v=1693838435https://www.elektor.com/cdn/shop/files/lcdisplay-smalla-web_1.jpg?v=1693838435,https://www.elektor.com/cdn/shop/files/lcdisplay-smallb-web_1.jpg?v=1693838435https://www.elektor.com/products/0-96-oled-display-for-arduino-128x64?variant=46907288453452 in stock 14.95 1 4.9 6.9 2 - 4 Werktage 46907229995340 01Space RP2040-0.42LCD Development Board Elektor Trade Bestsellers > Components > Development Boards > Displays & LEDs > Pico RP2040 > Raspberry Pi 020231 Arduino, MicroPython, and CircuitPython-compatible compact development board powered by Raspberry Pi RP2040RP2040-0.42LCD is a high-performance development board with integrated 0.42' LCD (70x40 resolution) with flexible digital interfaces.It incorporates Raspberry Pi's RP2040 microcontroller chip. The RP2040 features a dual-core Arm Cortex-M0+ processor clocked at 133 MHz with 264 KB internal SRAM and 2 MB flash storage.SpecificationsSoCRaspberry Pi RP2040 dual-core Cortex-M0+ microcontroller at up to 125 MHz, with 264 KB SRAMStorage2 MB SPI flashDisplay0.42-inch OLEDUSB1x USB Type-C port for power and programmingExpansion– Qwiic I²C connector– 7-pin and 8-pin headers with up to 11x GPIOs, 2x SPI, 2x I²C, 4x ADC, 1x UART, 5 V, 3.3 V, VBAT, GNDMisc– Reset and Boot buttons– RGB LED, power LEDPower supply– 5 V via USB-C port or Vin– VBAT pin for battery input– 3.3 V regulator with 500 mA peak outputDimensions23.5 x 18 mmWeight2.5 gDownloadsGitHub https://www.elektor.com/cdn/shop/files/01space-rp2040-0.42lcd-development-board.jpg?v=1698677752https://www.elektor.com/cdn/shop/files/01space-rp2040-0.42lcd-development-board_display.jpg?v=1698677752,https://www.elektor.com/cdn/shop/files/01space-rp2040-0.42lcd-development-board_pinout.jpg?v=1698677752https://www.elektor.com/products/01space-rp2040-0-42lcd-development-board?variant=46907229995340 in stock 19.95 12 4.9 6.9 2 - 4 Werktage 46912376734028 10x Micro-USB B Male Plug Connector Kit With Plastic Cover Kuongshun Trade Bestsellers 018705 Specifications Material: Plastic + Steel Quantity: 10Pieces Dimensions: 0.71 in x 0.39 in x 0.28 in Weight: 0.5oz/pc https://www.elektor.com/cdn/shop/files/18705_-_overview.jpg?v=1689238402https://www.elektor.com/cdn/shop/files/18705_-_single_unit.jpg?v=1693838454https://www.elektor.com/products/10x-micro-usb-b-male-plug-connector-kit-with?variant=46912376734028 in stock 7.95 19 4.9 6.9 2 - 4 Werktage 46907081294156 16 mm C-mount Lens (10 MP) for Raspberry Pi HQ Camera Module Raspberry Pi Foundation Trade Bestsellers > Cameras > Raspberry Pi > Raspberry Pi Accessories > Raspberry Pi Cameras 019281 The 16 mm lens provides a higher quality image than the 6 mm lens. It has a narrow angle of view which is more suited to viewing distant objects.SpecificationsResolution10 MegaPixelImage format1'Focal length16 mmApertureF1.4-16MountCField Angle 1'Field Angle 2/3'Field Angle 1/1.8'Field Angle 1/2'44.6° × 33.6°30.0° × 23.2°24.7° × 18.6°21.8° × 16.4°Back Focal Length17.53 mmOptical Length67.53 mmDistortion1'(-0.7%) 1/2'(-0.5%) 1/3'(-0.15%)M.O.D.0.2 mDimension39 × 50 mmWeight133.7 g https://www.elektor.com/cdn/shop/files/16-mm-c-mount-lens-10-mp-for-raspberry-pi-hq-camera-module.jpg?v=1698677762https://www.elektor.com/cdn/shop/files/16-mm-c-mount-lens-10-mp-for-raspberry-pi-hq-camera-module_side.jpg?v=1698677762,https://www.elektor.com/cdn/shop/files/16-mm-c-mount-lens-10-mp-for-raspberry-pi-hq-camera-module_connected_1.jpg?v=1698677762https://www.elektor.com/products/16-mm-c-mount-lens-10-mp-for-raspberry-pi-hq-camera-module?variant=46907081294156 in stock 64.95 47 0 6.9 2 - 4 Werktage 46907291697484 2-in-1 SMD Hot Air Rework Station ZD-8922 Zhongdi Boards&Kits Bestsellers > Comparison Websites DE > Comparison Websites FR > Elektor Labs Selection > Measuring Tools > No Member Discount > Platforms > Prototyping > Sale > Soldering Stations Comparison Websites 020141 This 2-in-1 SMD hot air soldering station offers a cost-effective solution for soldering and desoldering all types of SMD components. Features Incl. soldering iron and hot air pump. It is suitable for soldering and desoldering all types of surface mounted IC, PCB or components. The control unit has 2 LEDs that display the temperature and in °C and °F. The temperature can be easily adjusted with simple up/down buttoms. The hot air temperature can be calibrated from 3L/min to 24L/min continuously. Temperature is micro-processor controlled and can be adjusted. Temperature range: 50-480 °C for soldering iron, 100-500 °C for hot air pump. Specifications Power Soldering iron: 24 V, 60 WHot air pump: 300 W Power supply 220-240 VAC 50 Hz Temperature range Soldering iron: 50-480 °CHot air pump: 100-500 °C Dimensions 113 x 125 x 175 mm Weight 2 kg Included 1x Soldering station 1x Soldering iron 1x Hot air gun 3x Hot air nozzle 1x Soldering iron with needle bit 1x Power cord 1x Soldering iron stand with sponge https://www.elektor.com/cdn/shop/files/zd-8922-2-in-1-smd-hot-air-rework-station_branded.jpg?v=1689093305https://www.elektor.com/products/2-in-1-smd-hot-air-rework-station-zd-8922?variant=46907291697484 in stock 109.95 89.95 19 0 6.9 2 - 4 Werktage 46907288650060 2.2" SPI TFT Display Module ILI9341 (240x320) Kuongshun Trade Bestsellers > Components > Displays & LEDs MSP2202 ILI9341 is a 262144-color single-chip SOC driver for a TFT liquid crystal display with resolution of 240x320 dots (RGB), comprising a 720-channel source driver, a 320-channel gate driver, 172800 bytes GRAM for graphic display data of 240x320 dots (RGB), and power supply circuit.ILI9341 supports parallel 8-/9-/16-/18-bit data bus MCU interface, 6-/16-/18-bit data bus RGB interface and 3-/4-line serial peripheral interface (SPI).The moving picture area can be specified in internal GRAM by window address function. The specified window area can be updated selectively, so that moving picture can be displayed simultaneously independent of still picture area.ILI9341 can operate with 1.65V ~ 3.3V I/O interface voltage and an incorporated voltage follower circuit to generate voltage levels for driving an LCD.ILI9341 supports full color, 8-color display mode and sleep mode for precise power control by software and these features make the ILI9341 an ideal LCD driver for medium or small size portable products such as digital cellular phones, smart phone, MP3 and PMP where long battery life is a major concern.FeaturesDisplay resolution: 240 x 320 (RGB)Output: 720 source outputs | 320 gate outputs | Common electrode output (VCOM)a-TFT LCD driver with on-chip full display RAM: 172,800 bytesSystem Interface8-bits, 9-bits, 16-bits, 18-bits interface with 8080-Ⅰ/8080- Ⅱ series MCU6-bits, 16-bits, 18-bits RGB interface with graphic controller3-line / 4-line serial interfaceDisplay mode:Full color mode (Idle mode OFF): 262K-color Reduced color mode (Idle mode ON): 8-colorPower saving modes: Sleep mode Deep standby modeOn chip functions: VCOM generator and adjustment Timing generator Oscillator DC/DC converter Line/frame inversion 1 preset Gamma curve with separate RGB Gamma correctionContent Adaptive Brightness ControlMTP (3 times): 8-bits for ID1, ID2, ID3 7-bits for VCOM adjustment Low-power consumption architectureLow operating power supplies: VDDI = 1.65V ~ 3.3V (logic) VCI = 2.5V ~ 3.3V (analog) LCD Voltage drive: Source/VCOM power supply voltage AVDD - GND = 4.5V ~ 5.5V VCL - GND = -2.0V ~ -3.0V Gate driver output voltage VGH - GND = 10.0V ~ 20.0V VGL - GND = -5.0V ~ -15.0V VGH - VGL 3 ≦ 2V VCOM driver output voltage VCOMH = 3.0V ~ (AVDD – 0.5)V VCOML = (VCL+0.5)V ~ 0V VCOMH - VCOML ≦ 6.0V Operate temperature range: -40℃ to 85℃ https://www.elektor.com/cdn/shop/files/lcdisplay_spi_tft_a-web.jpg?v=1698677354https://www.elektor.com/cdn/shop/files/lcdisplay_spi_tft_b-web.jpg?v=1698677354,https://www.elektor.com/cdn/shop/files/lcdisplay_spi_tft_c-web.jpg?v=1698677354,https://www.elektor.com/cdn/shop/files/lcdisplay_spi_tft_d-web.jpg?v=1698677354,https://www.elektor.com/cdn/shop/files/ili9341handclock.png?v=1698677354,https://www.elektor.com/cdn/shop/files/ili9341-7segclock.png?v=1698677354https://www.elektor.com/products/2-2-spi-tft-display-module-ili9341-240x320?variant=46907288650060 in stock 22.95 16 4.9 6.9 2 - 4 Werktage 46907286421836 2x16 Character LCD Module (blue/white) Kuongshun Trade Bestsellers > Components > Displays & LEDs 017757 2x16 Character LCD Module (blue/white) Pin No. Pin Name Descriptions 1 VSS Ground 2 VDD Supply voltage for logic 3 V0 Input voltage for LCD 4 RS Data / Instruction Regster Select (H : Data signal, L : Instruction signal) 5 R/W Read / Write (H : Read mode, L : Write mode) 6 E Enable signal 7 DB0 Data bit 0 8 DB1 Data bit 1 9 DB2 Data bit 2 10 DB3 Data bit 3 11 DB4 Data bit 4 12 DB5 Data bit 5 13 DB6 Data bit 6 14 DB7 Data bit 7 15 LED_A Backlight Anode 16 LED_K Backlight Cathode https://www.elektor.com/cdn/shop/files/120061-77a-web.jpg?v=1689093141https://www.elektor.com/products/2x16-character-lcd-module-blue-white?variant=46907286421836 in stock 5.95 18 4.9 6.9 2 - 4 Werktage 46864032923980 303 circuits (EN) | E-book Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46864032923980-has-digital-downloads 0-905705-26-2 Like its predecessors in the 300 series of electronics projects books, 303 Circuits is aimed at the active electronics enthusiast, professional or amateur. Since the series was started in the early 1980s, many thousands of readers have found in these books that new approach, new concept, or new circuit they were looking for. In 303 Circuits you will find new ideas, new concepts and new circuits covering the gamut of electronics. The book is arranged in subject sections to make it easier for you to find the circuit or idea you are looking for. https://www.elektor.com/cdn/shop/products/303circuits.jpg?v=1688040959https://www.elektor.com/cdn/shop/files/303-circuits.jpg?v=1696848541https://www.elektor.com/products/303-circuits-ebook-en?variant=46864032923980 in stock 16.95 0 4.9 6.9 2 - 4 Werktage 47571218956620 309 Circuits (EN) | E-book Elektor Digital E-books Bestsellers > Books | Electronics > E-books (–20% for Members) has-digital-downloads,variant-47571218956620-has-digital-downloads - 309 Circuits (EN) | E-book https://www.elektor.com/cdn/shop/files/309-circuits_1.jpg?v=1705318955https://www.elektor.com/products/309-circuits-en-e-book?variant=47571218956620 in stock 19.95 0 4.9 6.9 2 - 4 Werktage 47570904449356 310 Circuits (EN) | E-book Elektor Digital E-books Bestsellers > Books | Electronics > E-books (–20% for Members) has-digital-downloads,variant-47570904449356-has-digital-downloads - 310 Circuits (EN) | E-book https://www.elektor.com/cdn/shop/files/14869.main_2.jpg?v=1705311837https://www.elektor.com/cdn/shop/files/310-circuits.jpg?v=1705311837https://www.elektor.com/products/310-circuits-en-e-book?variant=47570904449356 in stock 23.95 0 4.9 6.9 2 - 4 Werktage 47318723756364 311 Circuits (E-book) Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-47318723756364-has-digital-downloads 9781907920080 311 Circuits is the twelfth book in Elektor’s celebrated ‘300’ series. An immense source of inspiration for all electronics enthusiasts and professionals, this book deserves a place not far from the workbench.This book contains circuits, design ideas, tips and tricks from all areas of electronics: audio & video, computers & microcontrollers, radio, hobby & modelling, home & garden, power supplies & batteries, test & measurement, software, not forgetting a section ‘miscellaneous’ for everything that doesn’t fit in one of the other categories.311 Circuits presents complete solutions for numerous problems, as well as starting points for your own creations. 311 Circuits has been compiled from the 2009, 2010 and 2011 ‘Summer Circuits’ double editions of Elektor magazine. The book is mostly based on readers’ contributions, supplemented by circuits engineered and developed in the Elektor Labs. https://www.elektor.com/cdn/shop/files/311-circuits.jpg?v=1699463170https://www.elektor.com/products/311-circuits-e-book-en?variant=47318723756364 in stock 23.95 0 4.9 6.9 2 - 4 Werktage 47318767010124 3D Modeling and Printing for Electronics Elektor Publishing Books Bestsellers > Books > Books | Hobby & Modelling > NEW > No Member Discount 9783895765476 Learn to 3D Model & 3D Print with Tinkercad With this book and the complementary videos, you’ll be 3D printing in no time at all. This course is meant to have you make casings for electronic components but also goes into optimizing your print technique as well as adding a little flair to your 3D creations. The course is perfect for you if you just bought your (first) 3D printer and want to print your own designs as soon as possible while also being able to get more background information. You’ll get to know the workings of a 3D printer and what software to use to model your object, not forgetting to make it print perfectly. We’ll even use the magic of 3D printing to create things that appear impossible to make (this fast and simple) with any other rapid-prototyping technique. At the end of this course, it’ll be second nature for you to design an object for 3D printing and fine-tune your print-setting to get the perfect print! The book includes the following 7 video tutorials: Introduction Basic 3D modeling for 3D printing Modeling a casing Post-processing Pushing the limits Movable parts Snap fits https://www.elektor.com/cdn/shop/files/3d-modeling-and-printing-for-electronics.png?v=1699464497https://www.elektor.com/cdn/shop/files/3d-modeling-and-printing-for-electronics_tutorials.jpg?v=1699544479https://www.elektor.com/products/3d-modeling-and-printing-for-electronics?variant=47318767010124 in stock 34.95 72 4.9 6.9 2 - 4 Werktage 47318767108428 3D Modeling and Printing for Electronics (E-book) Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-47318767108428-has-digital-downloads Learn to 3D Model & 3D Print with Tinkercad With this book and the complementary videos, you’ll be 3D printing in no time at all. This course is meant to have you make casings for electronic components but also goes into optimizing your print technique as well as adding a little flair to your 3D creations. The course is perfect for you if you just bought your (first) 3D printer and want to print your own designs as soon as possible while also being able to get more background information. You’ll get to know the workings of a 3D printer and what software to use to model your object, not forgetting to make it print perfectly. We’ll even use the magic of 3D printing to create things that appear impossible to make (this fast and simple) with any other rapid-prototyping technique. At the end of this course, it’ll be second nature for you to design an object for 3D printing and fine-tune your print-setting to get the perfect print! The book includes the following 7 video tutorials: Introduction Basic 3D modeling for 3D printing Modeling a casing Post-processing Pushing the limits Movable parts Snap fits https://www.elektor.com/cdn/shop/files/3d-modeling-and-printing-for-electronics-pdf.png?v=1699464505https://www.elektor.com/cdn/shop/files/3d-modeling-and-printing-for-electronics_pdf_tutorials.jpg?v=1699544485https://www.elektor.com/products/3d-modeling-and-printing-for-electronics-e-book?variant=47318767108428 in stock 29.95 -1 4.9 6.9 2 - 4 Werktage 46907220394316 40-pin GPIO Header for Raspberry Pi (color-coded) Elektor Trade Bestsellers > No Member Discount > Raspberry Pi > Raspberry Pi Accessories 4251266700937 This color-coded pin header is ideal for use with Raspberry Pi. All pins are color-coded with corresponding functions making prototyping and hacking easier. Specifications Suitable for all Raspberry Pi models with GPIO 2 pin rows with 20 pins each 2.54 mm pin spacing (pitch) Pin height: 3 / 6 mm Total height: approx. 11 mm Colors/Functions Orange = 3.3 V Red = 5 V Pink = I²C Purple = UART Blue = SPI Yellow = DNC Green = GPIO Black = GND (Ground) https://www.elektor.com/cdn/shop/files/40-pin-gpio-header-for-raspberry-pi-color-coded.jpg?v=1689090727https://www.elektor.com/cdn/shop/files/40-pin-gpio-header-for-raspberry-pi-color-coded_front.jpg?v=1693838499https://www.elektor.com/products/40-pin-gpio-header-for-raspberry-pi-color-coded?variant=46907220394316 in stock 2.95 1.95 184 4.9 6.9 2 - 4 Werktage 46912376439116 4D Workshop4 IDE PRO (Download) 4D Systems bundels Bestsellers 4D Workshop4 IDE PRO (Download) 4D Systems 4D Workshop4 Integrated Development Environments PRO is a comprehensive software for Windows. It provides a software development platform for all of the 4D family of processors and modules, combining the Editor, Compiler, Linker, and Downloader to develop the complete 4DGL application code. You can choose your development environment (Designer, ViSi, ViSi - Genie, or Serial) based on your application requirements and your user skill levels. Performing high-level of customization with the featured Smart Widgets, Smart Widgets Editor, and Genie Magic - tools. Features Comprehensive software IDE for Windows environments Combines the Editor, Compiler, Linker, and Downloader Smart Widgets Editor, a comprehensive tool to create and animate Gauges, Sliders, Knobs etc. Genie Magic, adds standard 4DGL code to various points within the ViSi-Genie environment 4 development environments Designer ViSi ViSi - Genie Serial Demo Workshop4 PRO Smart Widgets Editor – Demo Compilation 1 | 4 |  Workshop4 PRO Smart Widgets Editor – Horizontal Progress Bar Compatibility: Workshop4 is compatible with Windows XP through to Windows 10. It is possible to run Workshop4 under a VM on Linux or Mac.   Full documentation and libraries are available here  A link to access your license keys and download information will be e-mailed once your order is finished processing. Software purchases completed Monday-Thursday before 4:00 p.m. should be delivered the next 48 hours. Please allow longer delay for license keys to be delivered if purchased Friday through Sunday.         https://www.elektor.com/cdn/shop/files/4d_workshop_pro.png?v=1689238395https://www.elektor.com/cdn/shop/files/4d_workshop_4_ide-quarterrotarymenu1.png?v=1696855378,https://www.elektor.com/cdn/shop/files/4d_workshop_4_ide-listbox1.png?v=1696855377,https://www.elektor.com/cdn/shop/files/4d_workshop_4_ide-carouselslider1.png?v=1696855377,https://www.elektor.com/cdn/shop/files/4d_workshop_4_ide-dropdownmenu1.png?v=1696855377,https://www.elektor.com/cdn/shop/files/4d_workshop_4_ide-smartgauge1.png?v=1700560112,https://www.elektor.com/cdn/shop/files/4d_workshop_4_ide-dockmenu1.png?v=1700560112https://www.elektor.com/products/4d-workshop4-ide-pro-download?variant=46912376439116 in stock 79.0 0 0 6.9 2 - 4 Werktage 46907290648908 4tronix M.A.R.S. Rover Robot Kit for Raspberry Pi Zero Elektor Trade Bestsellers > Raspberry Pi > Raspberry Pi Kits > Raspberry Pi Robots > Raspberry Pi Zero 8438513776839 Inspired by NASA's “Curiosity” and “Perseverance” Mars Rovers, this innovative M.A.R.S. Rover is an autonomous vehicle designed to drive around on rough terrain here on Earth. It uses the same rocker arm, bogey and differential arm mechanism. M.A.R.S. is an acronym for 'Mobile Autonomous Robotic System'. Features 6 Motors: 80 rpm 6 V, N20 micro gear motors 4 Servos: MG90S metal gear analog micro servos 4 FireLEDs Ultrasonic distance sensor on steerable mast Total number of special PCBs: 30 Number of different PCB designs: 11 Length: 200 mm Width: 185 mm Height with Mast: 170 mm Weight excluding Raspberry Pi Zero and batteries: 460 g There is a Python library module for the Raspberry Pi Zero that makes it easy to control the unit. Required Raspberry Pi Zero 4 rechargeable AA batteries Downloads Assembly of 4tronix M.A.R.S. Rover Kit Programming M.A.R.S. Rover on Raspberry Pi Zero Coding using Microsoft Makecode on GitHub https://www.elektor.com/cdn/shop/files/4tronix-mars-rover-robot-kit-for-raspberry-pi-zero.jpg?v=1698677790https://www.elektor.com/cdn/shop/files/4tronix-mars-rover-robot-kit-for-raspberry-pi-zero_top.jpg?v=1698677790https://www.elektor.com/products/4tronix-mars-rover-robot-kit-for-raspberry-pi-zero?variant=46907290648908 in stock 184.95 5 0 0 2 - 4 Werktage 46907047051596 4tronix Picon Zero v1.3 - Intelligent Robotics Controller for Raspberry Pi Elektor Trade Bestsellers > No Member Discount > Raspberry Pi > Raspberry Pi HATs > Raspberry Pi Zero > Sale 5053839113477 The Picon Zero is an add-on for the Raspberry Pi. It has the same size as a Raspberry Pi Zero, making it ideal to function as a pHat. Of course, it can be used on any other Raspberry Pi via a 40-pin GPIO connector.As well as two full H-Bridge motor drivers, the Picon Zero has several Input/Output pins giving you multiple configuration options. That allows you to easily add outputs or analog inputs to your Raspberry Pi without any complicated software or kernel-specific drivers. At the same time, it opens up 5 GPIO pins from the Raspberry Pi, and it provides the interface for an HC-SR04 ultrasonic distance sensor.The Picon Zero comes with all components, including the headers and screw terminals, fully soldered. Soldering isn't required. You can use it right out of the box.FeaturespHat format PCB: 65 mm x 30 mmTwo full H-Bridge motor drivers. Drive up to 1.5 A continuously per channel, at 3 V - 11 V.Each motor output has both a 2-pin male header and a 2-pin screw terminal.The motors can be powered from the Picon Zero's 5 V or an external power source (3 V - 11 V).The Picon Zero's 5 V can be selected to be from the Raspberry Pi's 5 V line, or a USB connector on the Picon Zero. That means that you can effectively have 2 USB battery banks: one to power the servos and motors on the Picon Zero and the other to power the Pi.4 Inputs that can accept up to 5 V. These inputs can be configured as follows:Digital inputsAnalog inputsDS18B20DHT116 Outputs that can drive 5 V and be configured as:Digital OutputPWM OutputServoNeoPixel WS2812All Inputs and Outputs use GVS 3-pin male headers.4-pin female header that connects directly to an HC-SR04 ultrasonic distance sensor.8-pin female header for Ground, 3.3 V, 5 V, and 5 GPIO signals allowing you to add their additional features.Hardware ConfigurationPicon Zero has two jumpers for setting the hardware configuration. Ensure that you have placed them in the correct position.JP1 – Board 5 V Selector. This jumper selects where to get the 5 V power from for the Picon Zero Outputs. The options are:Jumper at the top between RPI and 5 V. The 5 V power for the board is taken from the Raspberry Pi pins on the GPIO connector. Because of the low power output devices and the 5 V motors, all devices can be powered with a single 5 V power input.Jumper at the bottom between USB and 5 V. The 5 V power is taken from the microUSB connector on the Picon Zero. Useful for higher power output devices, since you can provide extra power through the micro-USB connector on the boardJP2 – Motor Power Selector. This jumper selects where the motors get the power. The two options here are the following:Jumper at the top between MotorPower and Vin. The motors are driven via the 2-pin screw terminal. The voltage can be between 3 V and 11 V. Useful for motors that require a voltage different from 5 V, or that require more current than is available on either of the USB input connectorsJumper at the bottom between 5 V and MotorPower. The motors are driven from the board's 5 V.Raspberry Pi ConfigurationThe Picon Zero is an I²C device. Make sure your Raspberry Pi is set up correctly to use I²C and SMBus:sudo apt-get install python-smbus python3-smbus python-dev python3-devsudo nano /boot/config.txt Add the following lines at the end of the filedtparam=i2c1=ondtparam=i2c_arm=onPress Ctrl-X and use the default prompts to savesudo rebootPlugin the Picon Zero onto the Pi and run i2cdetect -y 1If everything goes well, you will see the Picon Zero showing up as address 22 as shown below: https://www.elektor.com/cdn/shop/files/19077_-_overview.jpg?v=1698677796https://www.elektor.com/cdn/shop/files/19077_-_mounted.jpg?v=1698677796,https://www.elektor.com/cdn/shop/files/19077_-_input_output.jpg?v=1698677796,https://www.elektor.com/cdn/shop/files/19077_-_ultrasonic_sensor.jpg?v=1698677796https://www.elektor.com/products/4tronix-picon-zero-v1-3-intelligent-robotics-controller-for-raspberry-pi?variant=46907047051596 in stock 18.95 13.95 15 4.9 6.9 2 - 4 Werktage 46906958446924 5 V/2 A Micro-USB Voeding (EU) Kuongshun Trade Bestsellers > No Member Discount > Raspberry Pi > Raspberry Pi Accessories > Raspberry Pi Power Supplies > Sale 017589 5 V/2 A Micro-USB Voeding (EU) https://www.elektor.com/cdn/shop/files/sku17589-91a-web.jpg?v=1698677801https://www.elektor.com/cdn/shop/files/sku17589-91b-web.jpg?v=1698677801https://www.elektor.com/products/5-v-2-a-micro-usb-power-supply-eu?variant=46906958446924 in stock 9.95 7.95 8 4.9 6.9 2 - 4 Werktage 46906970145100 50 PIC Microcontroller Projects (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906970145100-has-digital-downloads 978-0-905705-88-0 This book contains 50 fun and exciting projects for PIC microcontrollers such as a laser alarm, USB teasing mouse, eggtimer, youth repellent, soundswitch, capacitive liquid level gauge, 'finger in the water' sensor, guarding a room using a camera, mains light dimmer (110-240 volts), talking microcontroller and much more. Several different techniques are discussed such as relay, alternating current control including mains, I²C, SPI, RS232, USB, pulse width modulation, rotary encoder, interrupts, infrared, analog-digital conversion (and the other way around), 7-segment display and even CAN bus.You can use this book to build the projects for your own use. The clear explanations, schematics and even pictures of each project make this a fun activity. For each project the theory is discussed and why the project has been executed in that particular way. That means you can also use this book as a studybook, or as basis for larger and more complicated projects. All projects use a breadboard so modification and expansion is easy.Three PIC microcontrollers are used, the 16f877A, 18f4455 and 18f4685. It is also discussed how you can migrate your project from one microcontroller to another – 15 types are supported - including two example projects.All software that is used in this book can be downloaded for free. That also applies to the open source programming language JAL. This powerful and yet easy to learn language is used by hobbyists as well as professionals.This book can also be used as a reference guide. It explains all JAL commands, as well as the expansion libraries. Using the index you can easily find example projects that illustrate the use of these commands. Even when you have built all projects in this book you will still want to keep it within arm's reach.This book is not a sequel but rather an expansion of the PIC Microcontrollers – 50 projects for beginners and experts book by the same author. If you own both books you have a whopping 100 projects for 6 different microcontrollers!On this page you'll find all the software which is discussed in the book. https://www.elektor.com/cdn/shop/files/50-pic-microcontroller-projects_ebook.jpg?v=1689084352https://www.elektor.com/products/50-pic-microcontroller-projects-e-book?variant=46906970145100 in stock 29.5 0 4.9 6.9 2 - 4 Werktage 46907080540492 6 mm CS-mount Lens (3 MP) for Raspberry Pi HQ Camera Module Raspberry Pi Foundation Trade Bestsellers > Cameras > Raspberry Pi > Raspberry Pi Accessories > Raspberry Pi Cameras 019280 This lens is suitable for basic photography. It can also be used for macro photography because it can focus objects at very short distances.SpecificationsImage format1/2'Focal length6 mmResolution3 MegaPixelApertureF1.2MountCSField Angle63°M.O.D.0.2 mBack Focal Length7.53 mmDimension30 x 34 mmWeight53 g https://www.elektor.com/cdn/shop/files/6-mm-cs-mount-lens-3-mp-for-raspberry-pi-hq-camera-module.jpg?v=1698677812https://www.elektor.com/cdn/shop/files/6-mm-cs-mount-lens-3-mp-for-raspberry-pi-hq-camera-module_side.jpg?v=1698677812,https://www.elektor.com/cdn/shop/files/6-mm-cs-mount-lens-3-mp-for-raspberry-pi-hq-camera-module_connected.jpg?v=1698677812https://www.elektor.com/products/6-mm-cs-mount-lens-3-mp-for-raspberry-pi-hq-camera-module?variant=46907080540492 in stock 32.95 31 4.9 6.9 2 - 4 Werktage 47310488699212 65 W USB-C PD GaN Power Supply FNIRSI Trade Bestsellers 020618 With this 65 W USB-C PD power supply (with GaN technology) and the included USB-C cable you can start using the FNIRSI HS-01 soldering iron straight away. Of course, you can also use this charger to fast charge your tablets and smartphones via USB-C and USB-A. Included 65 W USB-C PD GaN Power Supply (EU) USB-C cable (1.2 m) https://www.elektor.com/cdn/shop/files/65_w_usb-c_pd_gan_power_supply_eu.jpg?v=1699287219https://www.elektor.com/products/65-w-usb-c-pd-gan-power-supply?variant=47310488699212 in stock 24.95 32 4.9 6.9 2 - 4 Werktage 46906942587212 ABC of Capacitors Würth Trade Bestsellers > Books > Books | Electronics 1P744013 The author Stephan Menzel provides an introduction into capacitor technology and describes the wide range of capacitor types with their properties and parameters. Basic principles This chapter imparts basic knowledge on the relationships between the electric field, permittivity, as well as the structure and operating principles of a capacitor. Capacitor characteristics The electrical parameters and essential characteristics of a capacitor are explained in greater detail for the reader. This extends from the actual capacitance of a capacitor through to the interdependencies. Capacitor types Existing capacitor types and their characteristics are presented. Film, electrolyte and ceramic capacitors are considered in detail. https://www.elektor.com/cdn/shop/files/abc-of-capacitors.jpg?v=1689083710https://www.elektor.com/products/abc-of-capacitors?variant=46906942587212 in stock 9.9 30 4.9 6.9 2 - 4 Werktage 46907164000588 ABC of Capacitors (E-book) Würth E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907164000588-has-digital-downloads 978-3-89929-415-6 Contents Basic principles This chapter imparts basic knowledge on the relationships between the electric field, permittivity, as well as the structure and operating principles of a capacitor. Capacitor characteristics Here the electrical parameters and essential characteristics of a capacitor are explained in greater detail for the reader. This extends from the actual capacitance of a capacitor through to the interdependencies. Capacitor types Existing capacitor types and their characteristics are presented. Film, electrolyte and ceramic capacitors are considered in detail. https://www.elektor.com/cdn/shop/files/abc-of-capacitors-pdf.png?v=1689089046https://www.elektor.com/products/abc-of-capacitors-e-book?variant=46907164000588 in stock 8.99 0 4.9 6.9 2 - 4 Werktage 46907163345228 Abc of Power Modules (E-book) Würth E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907163345228-has-digital-downloads 978-3-89929-398-2 Functionality, structure and handling of a power moduleFor readers with first steps in power management the “Abc of Power Modules” contains the basic principles necessary for the selection and use of a power module. The book describes the technical relationships and parameters related to power modules and the basis for calculation and measurement techniques.ContentsBasicsThis chapter describes the need of a DC/DC voltage converter and its basic functionality. Furthermore, various possibilities for realizing a voltage regulator are presented and the essential advantages of a power module are mentioned.Circuit topologiesCircuit concepts, buck and boost topologies very frequently used with power modules are explained in detail and further circuit topologies are introduced.Technology, construction and regulation technologyThe mechanical construction of a power module is presented, which has a significant influence on EMC and thermal performance. Furthermore, control methods are explained and circuit design tips are provided in this chapter.Measuring methodsMeaningful measurement results are absolutely necessary to assess a power module. The relevant measurement points and measurement methods are described in this chapter.HandlingThe aspects of storage and handling of power modules are explained, as well as their manufacturing and soldering processes.Selection of a power modulesImportant parameters and criteria for the optimal selection of a power module are presented in this section. https://www.elektor.com/cdn/shop/files/abc-of-power-modules-pdf.png?v=1689089025https://www.elektor.com/products/abc-of-power-modules-e-book?variant=46907163345228 in stock 8.99 0 4.9 6.9 2 - 4 Werktage 46906985283916 Acoustics in Performance Elektor Publishing Books Bestsellers > Books > Books | Audio & RF > No Member Discount > Print Books Elektor Print Book 9781907920646 All you need to know about good acoustics and sound systems in performance and worship spaces!Everyone knows that the ability to hear music in balance and to understand speech is essential in any space used for performance or worship. Unfortunately, in the early 21st century, we find that buildings with good acoustics are the exception rather than the rule. Much of the fault leading to this result can be traced to the widespread perception that acoustics is a black art. In fact, scientific acoustics as developed in the last century is a well-defined engineering practice that can lead to predictable excellent results.A basic, non-engineering understanding of acoustics will help building owners, theater managers, ministers and teachers of music, performers, and other professionals to achieve their goals of excellent acoustics in venues with which they work. Performers having a basic understanding of acoustics will be able to make the most of the acoustics of the venue in which they perform.This book helps those responsible for providing good acoustics in performance and worship spaces to understand the variables and choices entailed in proper acoustic design for performance and worship. Practicing acoustical consultants will find the book a useful reference as well. The level of presentation is comfortable and straightforward without being simplistic. If correct acoustical principles are incorporated into the design, renovation, and maintenance of performance and worship venues, good acoustics will be the result. https://www.elektor.com/cdn/shop/files/acoustics-in-performance.png?v=1689084824https://www.elektor.com/products/acoustics-in-performance?variant=46906985283916 in stock 24.95 12.95 189 4.9 6.9 2 - 4 Werktage 46907076313420 Acoustics in Performance (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907076313420-has-digital-downloads All you need to know about good acoustics and sound systems in performance and worship spaces!Everyone knows that the ability to hear music in balance and to understand speech is essential in any space used for performance or worship. Unfortunately, in the early 21st century, we find that buildings with good acoustics are the exception rather than the rule. Much of the fault leading to this result can be traced to the widespread perception that acoustics is a black art. In fact, scientific acoustics as developed in the last century is a well-defined engineering practice that can lead to predictable excellent results.A basic, non-engineering understanding of acoustics will help building owners, theater managers, ministers and teachers of music, performers, and other professionals to achieve their goals of excellent acoustics in venues with which they work. Performers having a basic understanding of acoustics will be able to make the most of the acoustics of the venue in which they perform.This book helps those responsible for providing good acoustics in performance and worship spaces to understand the variables and choices entailed in proper acoustic design for performance and worship. Practicing acoustical consultants will find the book a useful reference as well. The level of presentation is comfortable and straightforward without being simplistic. If correct acoustical principles are incorporated into the design, renovation, and maintenance of performance and worship venues, good acoustics will be the result. https://www.elektor.com/cdn/shop/files/acoustics-in-performance-pdf.png?v=1689086661https://www.elektor.com/products/acoustics-in-performance-e-book?variant=46907076313420 in stock 19.95 0 4.9 6.9 2 - 4 Werktage 47310489223500 Acrylic Case for HackRF One SDR Great Scott Gadgets Trade Bestsellers > Radio | SDR 0636824571220 This clear acrylic case is the official case for the HackRF One board. It can replace the standard black plastic case of the HackRF One. Assembly Instructions Use a guitar pick or spudger to extract the HackRF One circuit board from the black plastic case. Insert one long screw into each corner of the bottom acrylic panel. Secure each long screw with a short (5 mm) spacer on the opposite side of the panel. Place the HackRF One circuit board (facing up) on top of the bottom panel, fitting the ends of the long screws through the corner mounting holes of the circuit board. Secure the circuit board with one long (6 mm) spacer in each corner. Place the top acrylic panel on top of the circuit board, aligning the cutouts with the circuit board’s expansion headers. Secure each corner with a short screw. Note: Do not overtighten! Hand-tighten only at every step. https://www.elektor.com/cdn/shop/files/acrylic-case-for-hackrf-one-sdr.png?v=1699287063https://www.elektor.com/products/acrylic-case-for-hackrf-one-sdr?variant=47310489223500 in stock 17.95 88 4.9 6.9 2 - 4 Werktage 47310489289036 Active Cooler for Raspberry Pi 5 Raspberry Pi Foundation Trade Bestsellers > No Member Discount > Raspberry Pi 5 > Raspberry Pi Accessories 5056561803357 The active cooler provides an alternative cooling solution for users who wish to use their Raspberry Pi 5 under sustained heavy load without a case. It combines a large metal heatsink with a variable-speed blower, again powered and controlled via the fan connector, and attaches to the Raspberry Pi 5 via sprung pins into a pair of mounting holes. https://www.elektor.com/cdn/shop/files/active-cooler-for-raspberry-pi-5.jpg?v=1699287182https://www.elektor.com/products/active-cooler-for-raspberry-pi-5?variant=47310489289036 in stock 7.95 254 4.9 6.9 2 - 4 Werktage 46906987413836 Active Cooling for Raspberry Pi (Mini Fan) JOY-iT Trade Raspberry Pi > Raspberry Pi Accessories If you are searching for a possibility to keep your Raspberry Pi cool, than this mini fan is the perfect possibility for this. The active cooler is ready to use right after pluging in the two GPIO pins into the 5V and GND GPI-O port. The cooler is compatible to all Raspberry Pis and is perfect to keep them cool, even under full load. Voltage: 5 V Current: 0.2 A Dimensions: 30 x 30 x 7 mm https://www.elektor.com/cdn/shop/files/active-cooling-for-raspberry-pi-mini-fan.jpg?v=1689084898https://www.elektor.com/products/active-cooling-for-raspberry-pi-mini-fan?variant=46906987413836 in stock 6.95 1 4.9 6.9 2 - 4 Werktage 46907014086988 Adafruit 2.5 W Class D Mono Amplifier (PAM8302) Adafruit Trade Bestsellers > Raspberry Pi > Raspberry Pi Accessories 018745 This small mono amplifier is surprisingly powerful - able to deliver up to 2.5 W into 4-8 Ω impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0 V - 5.5 V DC. Since the amplifier is a class D, it's very efficient making it perfect for portable and battery-powered projects. It has built-in thermal and over-current protection. There's even a volume trim pot so you can adjust the volume on the board down from the default 24 dB gain. The A+ and A- inputs of the amplifier go through 1.0 µF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio-pin to ground. The output is 'Bridge Tied' - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250 KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. The amplifier comes with a fully assembled and tested breakout board, a header to plug it into a breadboard and a 3.5 mm screw-terminal blocks so you can easily attach/detach your speaker. Speaker is not included, we recommend using any 4 Ω or greater impedance speaker. Features Output Power: 2.5 W at 4Ω, 10% THD (total harmonic distortion), 1.5 W at 8 Ω, 10% THD, with 5.5 V Supply 50 dB PSRR (power supply rejection ratio) at 1 KHz Filterless design, with ferrite bead + capacitors on output. Fixed 24 dB gain, an onboard trim potentiometer for adjusting input volume. Thermal and short-circuit/over-current protection Low current draw: 4 mA quiescent and 0.5 mA in shutdown (due to pull-up resistor on SD pin) https://www.elektor.com/cdn/shop/files/2130-00_1.jpg?v=1698677841https://www.elektor.com/cdn/shop/files/2130-04_1.jpg?v=1698677841,https://www.elektor.com/cdn/shop/files/2130-01_1.jpg?v=1698677841,https://www.elektor.com/cdn/shop/files/2130-03_1.jpg?v=1698677841https://www.elektor.com/products/adafruit-2-5-w-class-d-mono-amplifier-pam8302?variant=46907014086988 in stock 5.95 10 4.9 6.9 2 - 4 Werktage 46907007992140 Adafruit Adalogger FeatherWing (RTC + SD Add-on) Adafruit Trade Bestsellers > Components > Modules W8704-B This FeatherWing will make it easy to add data logging to any Feather Board you might have. You get both an I²C real-time clock (PCF8523) with 32 KHz crystal and battery backup, and a microSD socket that connects to the SPI port pins (+ extra pin for CS). Note: FeatherWing doesn't come with a microSD card. A CR1220 coin cell is required to use the RTC battery-backup capabilities. If you're not using the RTC part of the FeatherWing, a battery is not required. To talk to the microSD card socket Arduino's default SD library is recommended. Some light soldering is required to attach the headers onto the Wing. Pinouts Power pins On the bottom row, the 3.3 V (second from left) and GND (fourth from left) pin are used to power the SD card and RTC (to take a load off the coin cell battery when main power is available) RTC & I²C Pins In the top right, SDA (rightmost) and SCL (to the left of SDA) are used to talk to the RTC chip. SCL - I²C clock pin to connect to your microcontroller's I2C clock line. This pin has a 10 kΩ pull-up resistor to 3.3 V SDA - I²C data pin to connect to your microcontroller's I2C data line. This pin has a 10 kΩ pull-up resistor to 3.3 V There's also a breakout for INT which is the output pin from the RTC. It can be used as an interrupt output or it could also be used to generate a square wave. Note that this pin is an open drain - you must enable the internal pull-up on whatever digital pin it is connected to. SD & SPI Pins Starting from the left you've got SPI Clock (SCK) - output from feather to wing SPI Master Out Slave In (MOSI) - output from feather to wing SPI Master In Slave Out (MISO) - input from wing to feather These pins are in the same location on every Feather. They are used for communicating with the SD card. When the SD card is not inserted, these pins are completely free. MISO is tri-stated whenever the SD CS (chip select) pin is pulled high https://www.elektor.com/cdn/shop/files/2922-06.jpg?v=1698677851https://www.elektor.com/cdn/shop/files/2922-07.jpg?v=1698677851,https://www.elektor.com/cdn/shop/files/2922-08.jpg?v=1698677851,https://www.elektor.com/cdn/shop/files/2922-09.jpg?v=1698677851https://www.elektor.com/products/adafruit-adalogger-featherwing-rtc-sd-add-on?variant=46907007992140 in stock 10.95 19 4.9 6.9 2 - 4 Werktage 46907138572620 Adafruit BrainCraft HAT - Machine Learning for Raspberry Pi 4 Adafruit Trade Bestsellers > Raspberry Pi > Raspberry Pi HATs Features: 1.54' IPS TFT display with 240x240 resolution that can show text or video Stereo speaker ports for audio playback - either text-to-speech, alerts or for creating a voice assistant. Stereo headphone out for audio playback through a stereo system, headphones, or powered speakers. Stereo microphone input - perfect for making your very own smart home assistants Two 3-pin JST STEMMA connectors that can be used to connect more buttons, a relay, or even some NeoPixels! STEMMA QT plug-and-play I2C port can be used with any of Adafruits 50+ I2C STEMMA QT boards or can be used to connect to Grove I2C devices with an adapter cable. 5-Way Joystick + Button for user interface and control. Three RGB DotStar LEDs for colorful LED feedback. The STEMMA QT port means you can attach heat image sensors like the Panasonic Grid-EYE or MLX90640. Heat-Sensitive cameras can be used as a person detector, even in the dark! An external accelerometer can be attached for gesture or vibration sensing such as machinery/industrial predictive maintenance projects Please note: A Raspberry Pi 4 is not included. https://www.elektor.com/cdn/shop/files/adafruit_braincraft_hat_machine_learning_for_raspberry_pi_4_-_overview.jpg?v=1698677856https://www.elektor.com/cdn/shop/files/adafruit_braincraft_hat_machine_learning_for_raspberry_pi_4_-_display_and_fan.jpg?v=1698677856,https://www.elektor.com/cdn/shop/files/adafruit_braincraft_hat_machine_learning_for_raspberry_pi_4_-_assembled.jpg?v=1698677856,https://www.elektor.com/cdn/shop/files/adafruit_braincraft_hat_machine_learning_for_raspberry_pi_4_-_top_view.jpg?v=1698677856,https://www.elektor.com/cdn/shop/files/adafruit_braincraft_hat_machine_learning_for_raspberry_pi_4_-_size.jpg?v=1698677856https://www.elektor.com/products/adafruit-braincraft-hat-machine-learning-for-raspberry-pi-4?variant=46907138572620 in stock 49.95 10 4.9 6.9 2 - 4 Werktage 46907210039628 Adafruit Circuit Playground Bluefruit BLE Adafruit Trade Bestsellers > Components > Displays & LEDs 4333 Circuit Playground Bluefruit is the third board in the Circuit Playground series, another step towards a perfect introduction to electronics and programming. Adafruit has taken the popular Circuit Playground Express and made it even better! Now the main chip is an nRF52840 microcontroller which is not only more powerful, but also comes with Bluetooth Low Energy support for wireless connectivity. The board is round and has alligator-clip pads around it so you don't have to solder or sew to make it work. You can power it from USB, a AAA battery pack, or with a Lipoly battery (for advanced users). Circuit Playground Bluefruit has built-in USB support. Built in USB means you plug it in to program it and it just shows up, no special cable or adapter required. Just program your code into the board then take it on the go! Features 1x nRF52840 Cortex M4 processor with Bluetooth Low Energy support 10x mini NeoPixels, each one can display any color 1x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection) 1x Temperature sensor (thermistor) 1x Light sensor (phototransistor). Can also act as a color sensor and pulse sensor. 1x Sound sensor (MEMS microphone) 1x Mini speaker with class D amplifier (7.5 mm magnetic speaker/buzzer) 2x Push buttons, labeled A and B 1x Slide switch 8x alligator-clip friendly input/output pins Includes I²C, UART, 6 pins that can do analog inputs, multiple PWM outputs Green 'ON' LED so you know its powered Red '#13' LED for basic blinking Reset button 2 MB of SPI Flash storage, used primarily with CircuitPython to store code and libraries. MicroUSB port for programming and debugging USB port can act like serial port, keyboard, mouse, joystick or MIDI! Specifications Outer Diameter: ~50.6 mm / ~2.0' Weight: 8.9 g https://www.elektor.com/cdn/shop/files/adafruit-circuit-playground-bluefruit-ble.jpg?v=1689090542https://www.elektor.com/cdn/shop/files/adafruit-circuit-playground-bluefruit-ble_pcb.jpg?v=1693838622https://www.elektor.com/products/adafruit-circuit-playground-bluefruit-ble?variant=46907210039628 in stock 34.95 6 4.9 6.9 2 - 4 Werktage 46907117797708 Adafruit CLUE - nRF52840 Express with Bluetooth LE Adafruit Trade Bestsellers > Components > Development Boards P4500C Features Nordic nRF52840 Bluetooth LE processor – 1 MB of Flash, 256KB RAM, 64 MHz Cortex M4 processor 1.3″ 240×240 Color IPS TFT display for high-resolution text and graphics Power it from any 3-6V battery source (internal regulator and protection diodes) Two A / B user buttons and one reset button ST Micro series 9-DoF motion – LSM6DS33 Accel/Gyro + LIS3MDL magnetometer APDS9960 Proximity, Light, Color, and Gesture Sensor PDM Microphone sound sensor SHT Humidity BMP280 temperature and barometric pressure/altitude RGB NeoPixel indicator LED 2 MB internal flash storage for datalogging, images, fonts or CircuitPython code Buzzer/speaker for playing tones and beeps Two bright white LEDs in front for illumination / color sensing Qwiic / STEMMA QT connector for adding more sensors, motor controllers, or displays over I²C. You can plug in GROVE I²C sensors by using an adapter cable. Programmable with Arduino IDE or CircuitPython https://www.elektor.com/cdn/shop/files/adafruit-clue-nrf52840-express-with-bluetooth-le.jpg?v=1698677866https://www.elektor.com/cdn/shop/files/adafruit-clue-nrf52840-express-with-bluetooth-le_side.jpg?v=1698677866,https://www.elektor.com/cdn/shop/files/adafruit-clue-nrf52840-express-with-bluetooth-le_coin.jpg?v=1698677866https://www.elektor.com/products/adafruit-clue-nrf52840-express-with-bluetooth-le?variant=46907117797708 in stock 59.95 3 0 6.9 2 - 4 Werktage 46907207287116 Adafruit Feather 32u4 RFM69HCW Packet Radio (868 or 915 MHz) RadioFruit Adafruit Trade Bestsellers > Radio | SDR 3076 This 900 MHz radio version can be used for either 868 MHz or 915 MHz transmission/reception – the exact radio frequency is determined when you load the software since it can be tuned around dynamically. At the Feather 32u4's heart is at ATmega32u4 clocked at 8 MHz and at 3.3 V logic. This chip has 32 K of flash and 2 K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. To make it easy to use for portable projects, we added a connector for any 3.7 V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge. Features Measures 2.0' x 0.9' x 0.28' (51 x 23 x 8 mm) without headers soldered in Light as a (large?) feather – 5.5 grams ATmega32u4 @ 8 MHz with 3.3 V logic/power 3.3 V regulator with 500 mA peak current output USB native support, comes with USB bootloader and serial port debugging You also get tons of pins – 20 GPIO pins Hardware Serial, hardware I²C, hardware SPI support 7x PWM pins 10x analog inputs Built in 100 mA lipoly charger with charging status indicator LED Pin #13 red LED for general purpose blinking Power/enable pin 4 mounting holes Reset button The Feather 32u4 Radio uses the extra space left over to add an RFM69HCW 868/915 MHz radio module. These radios are not good for transmitting audio or video, but they do work quite well for small data packet transmission when you ned more range than 2.4 GHz (BT, BLE, WiFi, ZigBee) SX1231 based module with SPI interface Packet radio with ready-to-go Arduino libraries Uses the license-free ISM band ('European ISM' @ 868 MHz or 'American ISM' @ 915 MHz) +13 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software) 50 mA (+13 dBm) to 150 mA (+20 dBm) current draw for transmissions Range of approx. 350 meters, depending on obstructions, frequency, antenna and power output Create multipoint networks with individual node addresses Encrypted packet engine with AES-128 Simple wire antenna or spot for uFL connector Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. Headrs are also included so you can solder it in and plug into a solderless breadboard. You will need to cut and solder on a small piece of wire (any solid or stranded core is fine) in order to create your antenna. Lipoly battery and USB cable not included. https://www.elektor.com/cdn/shop/files/adafruit-feather-32u4-rfm69hcw-packet-radio-868-or-915mhz-radiofruit.jpg?v=1698677871https://www.elektor.com/cdn/shop/files/adafruit-feather-32u4-rfm69hcw-packet-radio-868-or-915mhz-radiofruit_top.jpg?v=1698677871,https://www.elektor.com/cdn/shop/files/adafruit-feather-32u4-rfm69hcw-packet-radio-868-or-915mhz-radiofruit_headers.jpg?v=1698677871https://www.elektor.com/products/adafruit-feather-32u4-rfm69hcw-packet-radio-868-or-915-mhz-radiofruit?variant=46907207287116 in stock 34.95 14 4.9 6.9 2 - 4 Werktage 46907211841868 Adafruit Feather nRF52840 Express Adafruit Trade Bestsellers > Components > Modules P4062 You can program the nRF52840 chip directly to take full advantage of the Cortex-M4 processor, and then calling into the Nordic SoftDevice radio stack when you need to communicate over BLE. Since the underlying API and peripherals are the same for the '832 and '840, you can supercharge your older nRF52832 projects with the same exact code, with a single recompile! CircuitPython works best with disk drive access, and this is the only BLE-plus-USB-native chip that has the memory to handle running a little Python interpreter. The massive RAM and speedy Cortex M4F chip make this a good match. Peripherals Plenty of GPIO, analog inputs, PWM, timers, etc. Best of all, it's got that native USB! Finally, no need for a separate USB serial chip like CP2104 or FT232. Serial is handled as a USB CDC descriptor, and the chip can act like a keyboard, mouse, MIDI device, or even disk drive. This chip has TinyUSB support – that means you can use it with Arduino as a native USB device and act as UART (CDC), HID, Mass Storage, MIDI, and more! Features ARM Cortex M4F (with HW floating point acceleration) running at 64 MHz 1 MB flash and 256 KB SRAM Native Open Source USB stack (pre-programmed with UF2 bootloader) Bluetooth Low Energy compatible 2.4 GHz radio FCC / IC / TELEC certified module Up to +8 dBm output power 1.7 V to 3.3 V operation with internal linear and DC/DC voltage regulators 21 GPIO, 6x 12-bit ADC pins, up to 12 PWM outputs (3 PWM modules with 4 outputs each) Pin #3 red LED for general purpose blinking, NeoPixel for colorful feedback Power/enable pin Measures 2.0 x 0.9 x 0.28' (51 x 23 x 7.2 mm) without headers soldered in Light as a (large?) feather (6 grams) 4 mounting holes Reset button SWD connector for debugging https://www.elektor.com/cdn/shop/files/adafruit-feather-nrf52840-express.jpg?v=1698677876https://www.elektor.com/cdn/shop/files/adafruit-feather-nrf52840-express_front.jpg?v=1698677876https://www.elektor.com/products/adafruit-feather-nrf52840-express?variant=46907211841868 in stock 32.95 8 4.9 6.9 2 - 4 Werktage 46907138834764 Adafruit Feather RP2040 Adafruit Trade Bestsellers > Pico RP2040 > Raspberry Pi > Raspberry Pi Accessories 019689 Inside the RP2040 is a 'permanent ROM' USB UF2 bootloader. What that means is when you want to program new firmware, you can hold down the BOOTSEL button while plugging it into USB (or pulling down the RUN/Reset pin to ground) and it will appear as a USB disk drive you can drag the firmware onto. Folks who have been using Adafruit products will find this very familiar – Adafruit uses the technique on all thier native-USB boards. Just note you don't double-click reset, instead hold down BOOTSEL during boot to enter the bootloader!The RP2040 is a powerful chip, which has the clock speed of our M4 (SAMD51), and two cores that are equivalent to our M0 (SAMD21). Since it is an M0 chip, it does not have a floating point unit, or DSP hardware support – so if you're doing something with heavy floating-point math, it will be done in software and thus not as fast as an M4. For many other computational tasks, you'll get close-to-M4 speeds!For peripherals, there are two I²C controllers, two SPI controllers, and two UARTs that are multiplexed across the GPIO – check the pinout for what pins can be set to which. There are 16 PWM channels, each pin has a channel it can be set to (ditto on the pinout).Technical SpecificationsMeasures 2.0 x 0.9 x 0.28' (50.8 x 22.8 x 7 mm) without headers soldered inLight as a (large?) feather – 5 gramsRP2040 32-bit Cortex M0+ dual core running at ~125 MHz @ 3.3 V logic and power264 KB RAM8 MB SPI FLASH chip for storing files and CircuitPython/MicroPython code storage. No EEPROMTons of GPIO! 21 x GPIO pins with following capabilities:Four 12 bit ADCs (one more than Pico)Two I²C, Two SPI and two UART peripherals, one is labeled for the 'main' interface in standard Feather locations16 x PWM outputs - for servos, LEDs, etcThe 8 digital 'non-ADC/non-peripheral' GPIO are consecutive for maximum PIO compatibilityBuilt in 200 mA+ lipoly charger with charging status indicator LEDPin #13 red LED for general purpose blinkingRGB NeoPixel for full color indication.On-board STEMMA QT connector that lets you quickly connect any Qwiic, STEMMA QT or Grove I²C devices with no soldering!Both Reset button and Bootloader select button for quick restarts (no unplugging-replugging to relaunch code)3.3 V Power/enable pinOptional SWD debug port can be soldered in for debug access4 mounting holes24 MHz crystal for perfect timing.3.3 V regulator with 500mA peak current outputUSB Type C connector lets you access built-in ROM USB bootloader and serial port debuggingRP2040 Chip FeaturesDual ARM Cortex-M0+ @ 133 MHz264 kB on-chip SRAM in six independent banksSupport for up to 16 MB of off-chip Flash memory via dedicated QSPI busDMA controllerFully-connected AHB crossbarInterpolator and integer divider peripheralsOn-chip programmable LDO to generate core voltage2 on-chip PLLs to generate USB and core clocks30 GPIO pins, 4 of which can be used as analog inputsPeripherals2 UARTs2 SPI controllers2 I²C controllers16 PWM channelsUSB 1.1 controller and PHY, with host and device support8 PIO state machinesComes fully assembled and tested, with the UF2 USB bootloader. Adafruit also tosses in some header, so you can solder it in and plug it into a solderless breadboard. https://www.elektor.com/cdn/shop/files/adafruit-feather-rp2040.jpg?v=1698677882https://www.elektor.com/cdn/shop/files/adafruit-feather-rp2040_front.jpg?v=1698677882,https://www.elektor.com/cdn/shop/files/adafruit-feather-rp2040_pinheaders.jpg?v=1698677882https://www.elektor.com/products/adafruit-feather-rp2040?variant=46907138834764 in stock 16.95 19 4.9 6.9 2 - 4 Werktage 46907259126092 Adafruit FT232H Breakout (USB to GPIO, SPI, I²C) Adafruit Trade Bestsellers > Components > Development Boards > Modules 2264 Wouldn't it be cool to drive a tiny OLED display, read a color sensor, or even just flash some LEDs directly from your computer? Sure you can program an Arduino or Trinket to talk to these devices and your computer, but why can't your computer just talk to those devices and sensors itself? Well, now your computer can talk to devices using the Adafruit FT232H breakout board! What can the FT232H chip do? This chip from FTDI is similar to their USB to serial converter chips but adds a 'multi-protocol synchronous serial engine' which allows it to speak many common protocols like SPI, I²C, serial UART, JTAG, and more! There's even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer! This chip is powerful and useful to have when you want to use Python (for example) to quickly iterate and test a device that uses I²C, SPI or plain general purpose I/O. There's no firmware to deal with, so you don't have to deal with how to 'send data to and from an Arduino which is then sent to and from' an electronic sensor or display or part. This breakout has an FT232H chip and an EEPROM for onboard configuration. Specifications Dimensions: 23 x 38 x 4 mm (0.9 x 1.5 x 0.2') Weight: 3.4 g Downloads CAD Files https://www.elektor.com/cdn/shop/files/adafruit-ft232h-breakout-usb-to-gpio-spi-i2c.jpg?v=1698677887https://www.elektor.com/cdn/shop/files/adafruit-ft232h-breakout-usb-to-gpio-spi-i2c_pins.jpg?v=1698677887,https://www.elektor.com/cdn/shop/files/adafruit-ft232h-breakout-usb-to-gpio-spi-i2c_connected.jpg?v=1698677887https://www.elektor.com/products/adafruit-ft232h-breakout-usb-to-gpio-spi-i2c?variant=46907259126092 in stock 22.95 9 4.9 6.9 2 - 4 Werktage 46907014316364 Adafruit Mini Metal Speaker with Wires (8 ohm, 0.5 W) Adafruit Trade Bestsellers > Cables & Wires > Components 018746 Specifications Datasheet Resonance Frequency (FO): 680 ±20% Hz at 1 V Rated Impedance: 8 ±20% Ω (at 1 KHz) Frequency Range: ~600-10 KHz Rated Input Power: 0.25 W Max Input Power: 0.5 W Temperature Range: -20ºC ~ 55ºC Dimensions Diameter: 28 mm / 1.1' Height: 4.5 mm Weight: 6 g https://www.elektor.com/cdn/shop/files/adafruit-mini-metal-speaker-with-wires.jpg?v=1689085409https://www.elektor.com/cdn/shop/files/adafruit-mini-metal-speaker-with-wires_back.jpg?v=1696849675https://www.elektor.com/products/adafruit-mini-metal-speaker-with-wires-8-ohm-0-5-w?variant=46907014316364 in stock 3.95 4 4.9 6.9 2 - 4 Werktage 46907236417868 Adafruit Zero Spy Camera for Raspberry Pi Zero (160 Degree Focal Angle) Adafruit Trade Bestsellers > Cameras > No Member Discount > Raspberry Pi > Raspberry Pi Cameras > Sale 5390 Is your house haunted? Or, rather, are you convinced that your house is haunted but have never been able to prove it since you've never had a camera that integrated with your Raspberry Pi Zero but was still small enough that the ghosts wouldn't notice it? Luckily, the spy camera for Raspberry Pi Zero is smaller than a thumbnail with a high enough resolution to see people, ghosts, or whatever it is you're looking for. It's about the size of a cell phone camera – the module being just 8.6 x 8.6 mm – with only a 2' cable, so you can create an extra compact and sneaky little spy cam. It has a 160-degree focal angle for a very wide/distorted fisheye effect that's great for security systems or watching a big swath of the living room or roadway. Like the Raspberry Pi camera board, it attaches to your Raspberry Pi Zero v1.3 or Zero W by way of the small socket on the board's edge closest to the 'PWR in' port. This interface uses the dedicated CSI interface, which was designed especially for interfacing to cameras. The CSI bus is capable of extremely high data rates, and it exclusively carries pixel data. The camera is connected to the BCM2835 processor on the RPi via the CSI bus, a higher bandwidth link which carries pixel data from the camera back to the processor. This bus travels along the ribbon cable that attaches the camera board to the Pi. The ribbon cables are compatible with both the RPi Zero v1.3 and RPi Zero W. The sensor itself has a native resolution of 5 megapixels and has a fixed focus lens onboard. It has similar specs as the original RPi camera, but is not as high-res as the new RPi camera v2! Specifications Camera Module Dimensions: 8.6 x 8.6 mm Lens Diameter: 10 mm Total Length: 60 mm Lens Focal Angle: 160 degrees Weight: 1.9 g https://www.elektor.com/cdn/shop/files/adafruit-zero-spy-camera-for-rpi-zero.jpg?v=1698677897https://www.elektor.com/cdn/shop/files/adafruit-zero-spy-camera-for-rpi-zero_front.jpg?v=1698677897https://www.elektor.com/products/adafruit-zero-spy-camera-for-raspberry-pi-zero-160-degree-focal-angle?variant=46907236417868 in stock 34.95 24.95 25 4.9 6.9 2 - 4 Werktage 46906988233036 Additional Camera for PeakTech 5600 (2 m flexible) PeakTech Trade Bestsellers > Components > Sensors & LiDAR 4250569403866 Dust and waterproof additional camera for our PeakTech 5600 with 6 dimmable LEDs for illumination of any object. The diameter of the flexible camera is only 8.2 mm and small enough to enter even the smallest openings. Suitable for all applications, the wide viewing angle of 60 °, as well as the automatic depth of focus from 30 mm to 'infinite' ensure a clear view of the object. Features 8,2 mm camera with 6 dimmable LEDs for illumination Camera is dust and waterproof according to IP67 2 m camera with flexible 'Goose-Neck' Specifications Diameter Camera 8.2 mm Viewing angle 60° Length Camera Shaft 200 cm (flexible), oil resistant lluminatin Camera 6x high-intensity LED white, dimmable Weight 350 g https://www.elektor.com/cdn/shop/files/additional-camera-for-peaktech-5600.jpg?v=1689084951https://www.elektor.com/products/additional-camera-for-peaktech-5600-2-m-flexible?variant=46906988233036 in stock 69.95 2 0 6.9 2 - 4 Werktage 46907088208204 Adjustable Raspberry Pi Camera Mount & Protector Elektor Trade Bestsellers > Cameras > Raspberry Pi > Raspberry Pi Accessories > Raspberry Pi Cameras 019362 Features Simple slide angle adjustment Camera Module protection 'sandwich' plates Made from crystal clear laser-cut acrylic in the UK 1/4 inch hole for tripod mounting Stable 4-leg base Here you can find the Assembly Instructions. https://www.elektor.com/cdn/shop/files/adjustable_raspberry_pi_camera_mount_protector.jpg?v=1689087193https://www.elektor.com/products/adjustable-raspberry-pi-camera-mount-protector?variant=46907088208204 in stock 9.95 10 4.9 6.9 2 - 4 Werktage 47884127109452 ADS-B Antenna (1090 MHz) Elektor Trade Bestsellers > NEW > Platforms > Radio | SDR 020846 This outdoor antenna made of fiberglass is optimized for the reception of ADS-B signals on the 1090 Mhz frequency. The antenna consists of a half-wave dipole with 5 dBi gain, encapsulated inside a fiberglass radome with an aluminum mounting base.With a Raspberry Pi, an RTL-SDR and this antenna, you can receive position data from aircraft in your area for apps such as Flightradar24 or FlightAware.SpecificationsFrequency1090 MHzAntenna typeDipole 1/2 waveConnectorN femaleInstallation typeMast Diam 35-60 mm (mounting bracket included)Gain5 dBiSWR≤1.5Type of PolarizationVerticalMaximum power10 WImpedance50 OhmsDimensions62.5 cmTube diameter26 mmBase antenna32 mmOperating temperature-30°C to +60°CIncludedADS-B antenna (1090 Mhz)Mast bracket (for installation on a 35 to 60 mm diameter mast) https://www.elektor.com/cdn/shop/files/ADS-B-Antenna-1090-MHz.jpg?v=1712242678https://www.elektor.com/cdn/shop/files/ADS-B-Antenna-1090-MHz_connector.jpg?v=1712242678https://www.elektor.com/products/ads-b-antenna-1090-mhz?variant=47884127109452 in stock 74.95 9 0 6.9 2 - 4 Werktage 46906942423372 Advanced Control Robotics (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Platforms > Robotics has-digital-downloads,variant-46906942423372-has-digital-downloads 9780963013330 If you enjoy DIY electronics, projects, software and robots, you’ll find this book intellectually stimulating and immediately useful. With the right parts and a little guidance, you can build robot systems that suit your needs more than overpriced commercial systems can. 20 years ago, robots based on simple 8-bit processors and touch sensors were the norm. Now, it’s possible to build multi-core robots that can react to their surroundings with intelligence. Today’s robots combine sensor readings from accelerometers, gyroscopes and computer vision sensors to learn about their environments. They can respond using sophisticated control algorithms and they can process data both locally and in the cloud. This book, which covers the theory and best practices associated with advanced robot technologies, was written to help roboticists, whether amateur hobbyist or professional, take their designs to the next level. As will be seen, building advanced applications does not require extremely costly robot technology. All that is needed is simply the knowledge of which technologies are out there and how best to use each of them. Each chapter in this book will introduce one of these different technologies and discuss how best to use it in a robotics application. On the hardware side, we’ll cover microcontrollers, servos, and sensors, hopefully inspiring you to design your own awe-inspiring, next-generation systems. On the software side, we’ll cover programming languages, debugging, algorithms, and state machines. We’ll focus on the Arduino, the Parallax Propeller, Revolution Education PICAXE and projects I’ve with which I’ve been involved, including the TBot educational robot, the PropScope oscilloscope, the 12Blocks visual programming language, and the ViewPort development environment. In addition, we’ll serve up a comprehensive introduction to a variety of essential topics, including output (e.g. LEDs, servo motors), and communication technologies (e.g. infrared, audio), that you can use to develop systems that interact to stimuli and communicate with humans and other robots. To make these topics as accessible as possible, handy schematics, sample code and practical tips regarding building and debugging have been included. Hanno Sander Christchurch, New Zealand https://www.elektor.com/cdn/shop/files/advanced-control-roboticsebook.jpg?v=1689083696https://www.elektor.com/cdn/shop/files/advanced-control-robotics_1.jpg?v=1696848620https://www.elektor.com/products/advanced-control-robotics-e-book?variant=46906942423372 in stock 20.95 0 4.9 6.9 2 - 4 Werktage 46907118321996 Advanced Programming with STM32 Microcontrollers Elektor Publishing Books Bestsellers > Books > Microcontrollers > Print Books > Programming Elektor Print Book 9783895764103 Master the software tools behind the STM32 microcontroller This book is project-based and aims to teach the software tools behind STM32 microcontroller programming. Author Majid Pakdel has developed projects using various different software development environments including Keil MDK, IAR Embedded Workbench, Arduino IDE and MATLAB. Readers should be able to use the projects as they are, or modify them to suit to their own needs. This book is written for students, established engineers, and hobbyists. STM32 microcontroller development boards including the STM32F103 and STM32F407 are used throughout the book. Readers should also find it easy to use other ARM-based development boards. Advanced Programming with STM32 Microcontrollers includes: Introduction to easy-to-use software tools for STM32 Accessing the features of the STM32 Practical, goal-oriented learning Complete code available online Producing practical projects with ease Topics cover: Pulse Width Modulation Serial Communication Watchdog Timers I²C Direct Memory Access (DMA) Finite State Machine Programming ADCs and DACs External Interrupts Timers and Counters https://www.elektor.com/cdn/shop/files/advanced-programming-with-stm32-microcontrollers.png?v=1689087704https://www.elektor.com/products/advanced-programming-with-stm32-microcontrollers?variant=46907118321996 in stock 29.95 33 4.9 6.9 2 - 4 Werktage 46907118518604 Advanced Programming with STM32 Microcontrollers (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907118518604-has-digital-downloads Master the software tools behind the STM32 microcontroller This book is project-based and aims to teach the software tools behind STM32 microcontroller programming. Author Majid Pakdel has developed projects using various different software development environments including Keil MDK, IAR Embedded Workbench, Arduino IDE and MATLAB. Readers should be able to use the projects as they are, or modify them to suit to their own needs. This book is written for students, established engineers, and hobbyists. STM32 microcontroller development boards including the STM32F103 and STM32F407 are used throughout the book. Readers should also find it easy to use other ARM-based development boards. Advanced Programming with STM32 Microcontrollers includes: Introduction to easy-to-use software tools for STM32 Accessing the features of the STM32 Practical, goal oriented learning Complete code available online Producing practical projects with ease Topics cover: Pulse Width Modulation Serial Communication Watchdog Timers I²C Direct Memory Access (DMA) Finite State Machine Programming ADCs and DACs External Interupts Timers and Counters https://www.elektor.com/cdn/shop/files/advanced-programming-with-stm32-microcontrollers-pdf.png?v=1689087718https://www.elektor.com/products/advanced-programming-with-stm32-microcontrollers-e-book?variant=46907118518604 in stock 24.95 0 4.9 6.9 2 - 4 Werktage 47400007205196 AE970D Soldering Station (80 W) incl. extra soldering tip Elektor Labs Boards&Kits Bestsellers > Elektor Labs Selection > Measuring Tools > NEW > No Member Discount > Soldering Stations 020731 Soldering station for precision soldering with actively heated soldering tip The AE970D soldering iron station is a 80 W high power tool to heat up to solder fastly. Its wide temperature range of 150-550°C (302-1022°F) could meet all your soldering needs. Thanks to its high performance plug-and-play integrated active tip, AE970D can reach melting point within 9 seconds. Patented close-loop automatic constant temperature control technology can ensure its soldering with high stability, excellent performance and precise accuracy. Features 80 W high power to enable fast heating up. Wider temperature range of 150-550°C (302-1022°F) to meet all your soldering needs. High performance plug-and-play integrated active tip, can reach melting point within 9 seconds. Patented close-loop automatic constant temperature control technology to ensure high stability, excellent performance and precise accuracy Specifications Power 80 W Input voltage 110 VAC / 230 VAC Output voltage 25 VAC Temperature range 150-550°C (302-1022°F) Heating element T80 series integrated active heater Temperature stability ±1°C/±1.8°F (when temperature >200°C/400°F) Tip to ground resistance <2 Ω Tip to ground voltage <2 mV Power cord length 1 m Handle cable length 1.2 m Dimensions 148 x 120 x 85 mm Weight (main unit) 1.33 kg Included Main unit Soldering iron incl. soldering tip T80-D24 Iron stand Brass wool Manual Extra: Soldering tip T80-BC3 free on top https://www.elektor.com/cdn/shop/files/AE970D-Soldering-Station.jpg?v=1710860445https://www.elektor.com/cdn/shop/files/AE970D-Soldering-Station_stand.jpg?v=1711533799,https://www.elektor.com/cdn/shop/files/AE970D-Soldering-Station_brass-wool.jpg?v=1711533812,https://www.elektor.com/cdn/shop/files/AE970D-Soldering-Station_side.jpg?v=1711533830,https://www.elektor.com/cdn/shop/files/AE970D-Soldering-Station_back.jpg?v=1711535704,https://www.elektor.com/cdn/shop/files/AE970D-Soldering-Station_contents.jpg?v=1711535717https://www.elektor.com/products/ae970d-soldering-station-80-w?variant=47400007205196 in stock 109.95 94.95 133 0 6.9 2 - 4 Werktage 46907259748684 AI at the Edge O'Reilly Media Trade Artificial Intelligence (AI) > Bestsellers > Books > Books | IoT & Automation > Programming 9781098120207 Solving Real-World Problems with Embedded Machine LearningEdge AI is transforming the way computers interact with the real world, allowing IoT devices to make decisions using the 99% of sensor data that was previously discarded due to cost, bandwidth, or power limitations. With techniques like embedded machine learning, developers can capture human intuition and deploy it to any target—from ultra-low power microcontrollers to embedded Linux devices.This practical guide gives engineering professionals, including product managers and technology leaders, an end-to-end framework for solving real-world industrial, commercial, and scientific problems with edge AI. You'll explore every stage of the process, from data collection to model optimization to tuning and testing, as you learn how to design and support edge AI and embedded ML products. Edge AI is destined to become a standard tool for systems engineers. This high-level road map helps you get started.Develop your expertise in AI and ML for edge devicesUnderstand which projects are best solved with edge AIExplore key design patterns for edge AI appsLearn an iterative workflow for developing AI systemsBuild a team with the skills to solve real-world problemsFollow a responsible AI process to create effective productsDownloadsErrataGitHub https://www.elektor.com/cdn/shop/files/ai-at-the-edge.png?v=1689092334https://www.elektor.com/products/ai-at-the-edge?variant=46907259748684 in stock 79.95 13 0 6.9 2 - 4 Werktage 46912383517004 Alchitry Au FPGA Development Board (Xilinx Artix 7) SparkFun Trade Bestsellers > Components > Development Boards > FPGA > Platforms DEV-16527 The Au continues the trend of more affordable and increasingly powerful FPGA boards arriving each year. This board is a fantastic starting point into the world of FPGAs and the heart of your next project. Finally, now that SparkFun builds this board, we added a Qwiic connector for easy I²C integration!The Alchitry Au features a Xilinx Artix 7 XC7A35T-1C FPGA with over 33,000 logic cells and 256 MB of DDR3 RAM. The Au offers 102 3.3 V logic level IO pins, 20 of which can be switched to 1.8 V; Nine differential analogue inputs; Eight general-purpose LEDs; a 100 MHz on-board clock that can be manipulated internally by the FPGA; a USB-C connector to configure and power the board; and a USB to serial interface for data transfer. To make getting started even easier, all Alchitry boards have full Lucid support, a built-in library of useful components to use in your project, and a debugger!FeaturesArtix 7 XC7A35T-1C - 33,280 logic cells256 MB DDR3 RAM102 IO pins (3.3 V logic level, 20 of them can be switched to 1.8 V for LVDS)Nine differential analogue inputs (One dedicated, Eight mixed with digital IO)USB-C to configure and power the boardEight general-purpose LEDsOne button (typically used as a reset)100 MHz on-board clock (can be multiplied internally by the FPGA)Powered with 5 V through USB-C port, 0.1' holes, or headersUSB to serial interface for data transfer (up to 12 Mbaud)Qwiic ConnectorDimensions: 65 x 45 mm https://www.elektor.com/cdn/shop/files/alchitry_au_fpga_development_board_xilinx_artix_7_-_overview.jpg?v=1689238587https://www.elektor.com/cdn/shop/files/alchitry_au_fpga_development_board_xilinx_artix_7_-_top_view.jpg?v=1696855429,https://www.elektor.com/cdn/shop/files/alchitry_au_fpga_development_board_xilinx_artix_7_-_bottom_view.jpg?v=1696855429,https://www.elektor.com/cdn/shop/files/alchitry_au_fpga_development_board_xilinx_artix_7_-_dimensions.jpg?v=1696855429https://www.elektor.com/products/alchitry-au-fpga-development-board-xilinx-artix-7?variant=46912383517004 in stock 149.95 5 0 0 2 - 4 Werktage 46907131593036 Alchitry Br Prototype Element Board SparkFun Trade Components > Modules DEV-16524 Alchitry Elements are expansion boards similar to shields for an Arduino or HATs for a Raspberry Pi, but these are meant for your Au and Cu FPGA Development Boards. This Element is equipped with four connectors on top and four on the bottom for maximum stackability that snaps to an Au or Cu board. https://www.elektor.com/cdn/shop/files/alchitry_br_prototype_element_board_-_overview.jpg?v=1698677929https://www.elektor.com/cdn/shop/files/alchitry_br_prototype_element_board_-_top_view.jpg?v=1698677929,https://www.elektor.com/cdn/shop/files/alchitry_br_prototype_element_board_-_bottom_view.jpg?v=1698677929,https://www.elektor.com/cdn/shop/files/alchitry_br_prototype_element_board_-_dimensions.jpg?v=1698677929https://www.elektor.com/products/alchitry-br-prototype-element-board?variant=46907131593036 in stock 24.95 1 4.9 6.9 2 - 4 Werktage 46907131298124 Alchitry Ft Element Board SparkFun Trade Bestsellers > Components > Modules DEV-17526 The Ft Element is equipped with four 50-pin board to board connectors on the underside and top of the board that snap to the Alchitry Au and Au(+) boards. It also adds a USB 3.0 200MB/s high-speed interface to your Alchitry board stack via the USB-C connector. Features USB-C connector w/ 200MB/s data rate to board to board connectors For use with projects that require data transfer rates greater than standard onboard USB to serial 12Mbaud 200 Mbps* ~ 191 Mbaud* - Note: this is not exact and depends on how you are using the Dev board in conjunction with the FT element board. https://www.elektor.com/cdn/shop/files/alchitry_ft_element_board_-_overview.jpg?v=1698677940https://www.elektor.com/cdn/shop/files/alchitry_ft_element_board_-_top_view.jpg?v=1698677940,https://www.elektor.com/cdn/shop/files/alchitry_ft_element_board_-_bottom_view.jpg?v=1698677940,https://www.elektor.com/cdn/shop/files/alchitry_ft_element_board_-_dimensions.jpg?v=1698677940https://www.elektor.com/products/alchitry-ft-element-board?variant=46907131298124 in stock 44.95 2 4.9 6.9 2 - 4 Werktage 46906944651596 Analogue Video (E-BOOK) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906944651596-has-digital-downloads 9780905705965 This e-book is intended for electronics enthusiasts and professionals alike, who want a much deeper understanding of the incredible technology conquests over the pre-digital decades that created video. It details evolution of analogue video electronics and technology from the first electro-mechanical television, through advancements in Cathode Ray Tubes, transistor circuits and signal processing, up to the latest analogue, colour-rich TV, entertainment devices and calibration equipment. Key technological advances that enabled monochrome video and, eventually, colour are explained. The importance, compromises and techniques of maintaining crucial backward legacy compatibilities are described. The generation, signal processing and playback of analogue video signals in numerous capture, display, recording and playback devices together with operating principles and practices are examined. Technical and, often, political merits and deficiencies of key national and international video standards are highlighted. Several formats are shown to win and ultimately to co-exist. This e-book begins at fairly basic levels; concepts are introduced with human physiological perceptions of light and colour explained. This leads to the subject matter of luminance and chrominance; their equations and the circuits to process. There is full, detailed analysis of waveform shapes and timings inside video equipment and relevant popular connections e.g. S-video. Several analogue video projects which you can build yourself are also included in this book; with schematics, circuit board layouts and calibration steps to help you obtain the best results. The book makes use of many colour pages where the subject matter demands it (e.g. test cards). If you really want a deeper understanding of analogue video then this e-book is for you! https://www.elektor.com/cdn/shop/files/15318.main_3.jpg?v=1689083766https://www.elektor.com/cdn/shop/files/analogue-video.jpg?v=1696848664https://www.elektor.com/products/analogue-video-e-book?variant=46906944651596 in stock 19.95 0 4.9 6.9 2 - 4 Werktage 46906971128140 Andonstar A1 USB Digital Microscope Andonstar Trade Bestsellers > Measuring Tools > Microscopes > Production & Repair > Sale 018131 Specifications DSP: High power Digital Image Monarch Processor Sensor: high-quality CMOS sensor, 2M pixel (hardware, no Interpolation) Resolution: 640x480,1600x1200 Interface: USB 1.1 / USB 2.0 Frame rate: 30 frames/sec (When resolution at 640x480), 1600x1200 5 frames/sec Focal distance: 5-30 mm (when Focal distance infinity, the microscope as a webcam, can not magnify) Magnification: Please refer to the sample photos and video Diameter: 12 mm USB cable length: about 165 cm USB cable color: black or transparent color (random) Lighting: 8x LED around the camera lens Included 1x Digital Microscope Camera 1x Software CD (User manual included) 1x Metal big base Stand https://www.elektor.com/cdn/shop/files/andonstar-microscope-a1.jpg?v=1698677954https://www.elektor.com/cdn/shop/files/andonstar-microscope-a1-use.jpg?v=1698677954,https://www.elektor.com/cdn/shop/files/andonstar-microscope-a1-dimensions.jpg?v=1698677954,https://www.elektor.com/cdn/shop/files/andonstar-microscope-a1-pcb1.jpg?v=1698677954,https://www.elektor.com/cdn/shop/files/andonstar-microscope-a1-pcb2.jpg?v=1698677954,https://www.elektor.com/cdn/shop/files/20170118162408_led2.png?v=1698677954,https://www.elektor.com/cdn/shop/files/20170118161746_led1.png?v=1698677954https://www.elektor.com/products/andonstar-a1-usb-digital-microscope?variant=46906971128140 in stock 79.95 54.95 3 0 6.9 2 - 4 Werktage 46907226227020 Andonstar AD1605 4K HDMI Digital Microscope Andonstar Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > No Member Discount > Production & Repair > Sale Comparison Websites 020183 The Andonstar AD1605 4K Digital Microscope features a 140 megapixels HD sensor, an oversized metal base and an adjustable bracket. With 4k ultra HD image sensor, you can capture high-quality pictures and record ultra-clear videos. This 4K digital microscope possesses a magnification up to 150X. With a stand size of 37.5 x 25 x 47 cm, it can offer a large working space that is ideal for assembly, inspection, training, real-time viewing, image capture and video documentation. With it, you can check the solder joint of a circuit board, or the minute structure of coin, jewelry, textile, skin, insect, etc. Features 140 MP HD sensor providing clear images of high quality Deep depth of field making images sharp and clear Oversized metal base providing large working space Wide focus range from 5 to 29 cm Adjustable metal bracket for easy adjustment of magnification and object distance Image capture & video record function for convenient documentation of work UV Filter to protect the lens from the oil, heat, dirt or dust during soldering or repair IR remote control for easy operation and avoid the shake of the microscope with the button playing Memory card with up to 32 GB storage (not included in the package) Applications Phone repair PCB checking Plants & insects Arts & crafts/miniature Printings/textile Assembling line Antique authentication Jewelry appraisal Watch repair DIY Specifications Image sensor 140 MP Video output 3840x2160 (30fps)2560x1440 (24fps)1920x1080 (60fps/30fps) Video format MP4 Magnification Up to 150 times (29 inch HDMI monitor) Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range 5-29 cm Frame Rate Max. 60fps Video interface HDMI Storage microSD card (up to 32 GB) PC support No Power source 5 V DC Light source 2 LEDs with the stand Stand size 37.5 x 25 x 47 cm Weight 5.5 kg Included 1x Andonstar AD1605 Digital Microscope 1x Metal stand 1x UV filter 1x IR remote 1x Switch cable 1x Power adapter 1x User manual https://www.elektor.com/cdn/shop/files/andonstar-ad1605-4k-hdmi-digital-microscope.jpg?v=1698677965https://www.elektor.com/cdn/shop/files/andonstar-ad1605-4k-hdmi-digital-microscope_remote.jpg?v=1698677965,https://www.elektor.com/cdn/shop/files/andonstar-ad1605-4k-hdmi-digital-microscope_screen.jpg?v=1698677965,https://www.elektor.com/cdn/shop/files/andonstar-ad1605-4k-hdmi-digital-microscope_connecting.jpg?v=1698677965,https://www.elektor.com/cdn/shop/files/andonstar-ad1605-4k-hdmi-digital-microscope_features.jpg?v=1698677965https://www.elektor.com/products/andonstar-ad1605-4k-hdmi-digital-microscope?variant=46907226227020 in stock 399.0 349.0 14 0 0 2 - 4 Werktage 46907221147980 Andonstar AD203 4" Handheld Digital Microscope Andonstar Trade Bestsellers > Measuring Tools > Microscopes > Production & Repair 020146 Applications Coin collection Printing Textiles Micro engraving/Jewelry Watch repair Botany & Entomology Specifications Image sensor 2 Megapixels HD Sensor Display resolution 800 x 480 Display size 4-inch Video output FHD 1920x1080 (30fps)1080P 1440x1080 (30fps)720P 1280x720 (30fps) Video format AVI Magnification Built-in 4-inch screen: 28x3x digital magnification: 84xFull screen of 30-inch computer: 200x Photo resolution Up to 12 MP (4032 x 3024) Photo format JPG Focus range Minimum 1 cm Frame rate 30fps Storage microSD card, up to 32 GB PC support Windows 7/8/10 (Amcap software) Power source USB 5 V DC Light source The lens with 8 adjustable LED lights Stand size 18 x 20 x 18 cm Product size 18 x 13 x 4 cm Weight 0.215 kg Language support English, French, German, Spanish, Italian, Portuguese, Russian, Simplified Chinese, Traditional Chinese, Korean, Vietnamese, Japanese Included 1x Andonstar AD203 handheld microscope 1x Power cable 1x 32 GB SD card 1x Portable wrist strap 1x Portable bag 1x Instructions Downloads Amcap Software https://www.elektor.com/cdn/shop/files/andonstar-ad203-handheld-digital-microscope.jpg?v=1689090763https://www.elektor.com/cdn/shop/files/andonstar-ad203-handheld-digital-microscope_screen.jpg?v=1696853569https://www.elektor.com/products/andonstar-ad203-4-handheld-digital-microscope?variant=46907221147980 in stock 69.95 8 0 6.9 2 - 4 Werktage 46907256471884 Andonstar AD246S-M 7" 3-Lens HDMI Digital Microscope Andonstar Trade Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > NEW > No Member Discount > Production & Repair Comparison Websites 020433 This versatile microscope covers a wide magnification range (60-240x, 18-720x, 1560-2040x) with 3 lenses. With this digital microscope, you can examine plants, insects, gems and coins, or do electronic work such as repairing or making circuit boards. Specificaties AD246S-M AD249S-M Magnification Lens A 18-720 18-720 Focus range 12-320 mm 12-320 mm Lens D 1800-2040 1800-2040 Focus range 4-5 mm 4-5 mm Lens L 60-240 60-240 Focus range 90-300 mm 90-300 mm Screen size 7 inch (17,8 cm) 10 inch (25,7 cm) Video resolution (max.) UHD 2880x2160 (24fps) UHD 2880x2160 (24fps) Video format MP4 MP4 Photo format JPG JPG Photo resolution 5600x2400 (with interpolation) 5600x2400 (with interpolation) Frame rate Max. 120fps Max. 120fps HDMI output Yes (support dual-screen display) Yes (only HDMI monitor displays) PC output Yes Yes Stand size 20 x 18 x 30 cm 20 x 18 x 30 cm Inbegrepen 1x Andonstar AD246S-M Digital Microscope 3x Lenses (A, D & L) 1x Slide holder 1x 32 GB microSD card 1x USB cable 1x Switch cable 1x HDMI cable 1x Remote control 5x Prepared Slides 1x Observation box 1x Tweezers 1x User manual Downloads User Manual Software https://www.elektor.com/cdn/shop/files/andonstar-ad246s-m-3-lens-hdmi-digital-microscope-with-7-inch-lcd.jpg?v=1702653404https://www.elektor.com/cdn/shop/files/andonstar-ad246s-m-3-lens-hdmi-digital-microscope-with-7-inch-lcd_lenses.jpg?v=1702653404,https://www.elektor.com/cdn/shop/files/andonstar-ad246s-m-3-lens-hdmi-digital-microscope-with-7-inch-lcd_magnification.jpg?v=1702653404,https://www.elektor.com/cdn/shop/files/andonstar-ad246s-m-3-lens-hdmi-digital-microscope-with-7-inch-lcd_video.jpg?v=1702653404,https://www.elektor.com/cdn/shop/files/andonstar-ad246s-m-3-lens-hdmi-digital-microscope-with-7-inch-lcd_dimensions.jpg?v=1702653404,https://www.elektor.com/cdn/shop/files/andonstar-ad246s-m-3-lens-hdmi-digital-microscope-with-7-inch-lcd_contents.jpg?v=1702653404https://www.elektor.com/products/andonstar-ad246s-m-7-3-lens-hdmi-digital-microscope?variant=46907256471884 in stock 239.0 199.95 1 0 0 2 - 4 Werktage 46907292352844 Andonstar AD249S-M 10.1" 3-Lens HDMI Digital Microscope Andonstar Trade Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > NEW > No Member Discount > Production & Repair Comparison Websites 020432 This versatile microscope covers a wide magnification range (60-240x, 18-720x, 1560-2040x) with 3 lenses. With this digital microscope, you can examine plants, insects, gems and coins, or do electronic work such as repairing or making circuit boards. Specifications AD246S-M AD249S-M Magnification Lens A 18-720 18-720 Focus range 12-320 mm 12-320 mm Lens D 1800-2040 1800-2040 Focus range 4-5 mm 4-5 mm Lens L 60-240 60-240 Focus range 90-300 mm 90-300 mm Screen size 7 inch (17.8 cm) 10 inch (25.7 cm) Video resolution (max.) UHD 2880x2160 (24fps) UHD 2880x2160 (24fps) Video format MP4 MP4 Photo format JPG JPG Photo resolution 5600x2400 (with interpolation) 5600x2400 (with interpolation) Frame rate Max. 120fps Max. 120fps HDMI output Yes (support dual-screen display) Yes (only HDMI monitor displays) PC output Yes Yes Stand size 20 x 18 x 30 cm 20 x 18 x 30 cm Included 1x Andonstar AD249S-M Digital Microscope 3x Lenses (A, D & L) 1x Slide holder 1x 32 GB microSD card 1x USB cable 1x Switch cable 1x HDMI cable 1x Remote control 5x Prepared Slides 1x Observation box 1x Tweezers 1x User manual Downloads User Manual Software https://www.elektor.com/cdn/shop/files/andonstar-ad249s-m-3-lens-hdmi-digital-microscope-with-10-inch-lcd.jpg?v=1700037542https://www.elektor.com/cdn/shop/files/andonstar-ad249s-m-3-lens-hdmi-digital-microscope-with-10-inch-lcd_lenses.jpg?v=1700037542,https://www.elektor.com/cdn/shop/files/andonstar-ad249s-m-3-lens-hdmi-digital-microscope-with-10-inch-lcd_magnification.jpg?v=1700037542,https://www.elektor.com/cdn/shop/files/andonstar-ad249s-m-3-lens-hdmi-digital-microscope-with-10-inch-lcd_video.jpg?v=1700560097,https://www.elektor.com/cdn/shop/files/andonstar-ad249s-m-3-lens-hdmi-digital-microscope-with-10-inch-lcd_dimensions.jpg?v=1700560097,https://www.elektor.com/cdn/shop/files/andonstar-ad249s-m-3-lens-hdmi-digital-microscope-with-10-inch-lcd_contents.jpg?v=1700560097https://www.elektor.com/products/andonstar-ad249s-m-10-1-3-lens-hdmi-digital-microscope?variant=46907292352844 out of stock 289.0 239.0 0 0 0 nicht auf Lager 47310489420108 Andonstar AD249S-P 10.1" 3-Lens HDMI Digital Coin Microscope Andonstar Trade Measuring Tools > Microscopes > No Member Discount 020669 This versatile digital microscope covers a wide magnification range (18-720x, 1560-2040x, 2760-4080x) with 3 lenses for hobby, industrial and biologic purposes. Lens A (18-720x) can be used to observe whole coins or parts, circuit boards, plants, stones, etc. With lens B (1560-2040x) and C (2760-4080x) you can observe biological slides. Specifications Magnification Lens A 18-720 Focus range 12-320 mm Lens B 1560-2040 Focus range 7-8 mm Lens C 2760-4080 Focus range 3-4 mm Screen size 10 inch (25.7 cm) Video resolution (max.) UHD 2880x2160 (24fps) Video format MP4 Photo format JPG Photo resolution 5600x2400 (with interpolation) Frame rate Max. 120fps HDMI output Yes (only HDMI monitor displays) PC output Yes Power supply USB 5 V DC (not included) Stand material Pro Plastic Stand size 20 x 19 x 30 cm Included 1x Andonstar AD249S-P Digital Microscope 1x Pro plastic stand 1x Lens A (fixed) 1x Lens (B & C) 1x USB cable 1x HDMI cable 1x Remote control 1x Dimmer cable 3x Backdrop board 1x Slides kit 1x 32 GB microSD card 1x Observation box 1x Tweezers 1x Screw driver 1x User manual https://www.elektor.com/cdn/shop/files/Andonstar-AD249S-P-Digital-Microscope.jpg?v=1702909865https://www.elektor.com/cdn/shop/files/Andonstar-AD249S-P-Digital-Microscope_remote.jpg?v=1702909871,https://www.elektor.com/cdn/shop/files/Andonstar-AD249S-P-Digital-Microscope_coin.jpg?v=1702909877,https://www.elektor.com/cdn/shop/files/Andonstar-AD249S-P-Digital-Microscope_lenses.jpg?v=1702909883,https://www.elektor.com/cdn/shop/files/Andonstar-AD249S-P-Digital-Microscope_contents.jpg?v=1702909888https://www.elektor.com/products/andonstar-ad249s-p-10-1-3-lens-hdmi-digital-coin-microscope?variant=47310489420108 out of stock 209.0 169.95 -1 0 0 nicht auf Lager 46907291795788 Andonstar AD407 7" HDMI Digital Microscope Andonstar Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > No Member Discount > Production & Repair > Sale Comparison Websites 019079 Examine your circuits with high precision and solder even the smallest SMDs and elements without any hassle. Features Multifunctional HDMI Digital Microscope features Full HD, comfortable headroom, improved ergonomy, multiple output signals with different resolutions. Tilt angle of the wide LCD monitor is adjustable. Comes with remote control. Can be used as stand-alone. Specifications Screen size 7 inch (17.8 cm) Image sensor 4 MP Video output UHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps) Video format MP4 Magnification Up to 270 times (27 inch HDMI monitor) Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range Min. 5 cm Frame rate Max. 120fps (under 600 Lux Brightness & HDP120) Video interface HDMI Storage microSD card (up to 32 GB) Power source 5 V DC Light source 2 LEDs with the stand Stand size 20 x 12 x 19 cm Included 1x Andonstar AD407 Digital Microscope 1x Metal stand with 2 LEDs 1x Optical bracket 1x UV filter 1x IR remote 1x Switch cable 1x Power adapter 1x HDMI cable 2x Screws 1x Screwdriver 1x User manual Downloads User Manual Model Comparison AD407 AD407 Pro AD409 AD409 Pro-ES Screen size 7 inch (17.8 cm) 7 inch (17.8 cm) 10.1 inch (25.7 cm) 10.1 inch (25.7 cm) Image sensor 4 MP 4 MP 4 MP 4 MP Video output 2160p 2160p 2160p 2160p Interfaces HDMI HDMI USB, HDMI, WiFi USB, HDMI, WiFi Video format MP4 MP4 MP4 MP4 Magnification Up to 270x Up to 270x Up to 300x Up to 300x Photo resolution Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Photo format JPG JPG JPG JPG Focus distance Min. 5 cm Min. 5 cm Min. 5 cm Min. 5 cm Frame rate Max. 120f/s Max. 120f/s Max. 120f/s Max. 120f/s Storage microSD card microSD card microSD card microSD card PC support No No Windows Windows Mobile connection No No WiFi + Measurement WiFi + Measurement Power source 5 V DC 5 V DC 5 V DC 5 V DC Light source 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand Endoscope No No No Yes Stand size 20 x 12 x 19 cm 20 x 18 x 32 cm 18 x 20 x 30 cm 18 x 20 x 32 cm Weight 1.6 kg 2.1 kg 2.2 kg 2.5 kg Price €259.00€199.00 €289.00€229.00 €399.00€279.00 €449.00€299.00 https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_angle.jpg?v=1698675817https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_pcb.jpg?v=1698675817,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope.jpg?v=1698675817,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_side.jpg?v=1700560087,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_back.jpg?v=1700560087,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_features.jpg?v=1700560088,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_hdmi.jpg?v=1700560088,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_screen.jpg?v=1700560087,https://www.elektor.com/cdn/shop/files/andonstar-ad407-digital-microscope_connectors.jpg?v=1700560087https://www.elektor.com/products/andonstar-ad407-7-hdmi-digital-microscope?variant=46907291795788 in stock 259.0 199.95 9 0 0 2 - 4 Werktage 46907256406348 Andonstar AD407 Pro 7" HDMI Digital Microscope Andonstar Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > NEW > No Member Discount > Production & Repair > Sale Comparison Websites 020429 The Andonstar AD407 Pro microscope is suitable for various applications such as soldering SMDs or repair work. The microscope has a large adjustable 7' LCD display and comes with a remote. Compared to AD407, AD407 Pro offers an extra-high stand, which makes soldering of components even easier. Specifications Screen size 7 inch (17.8 cm) Image sensor 4 MP Video output UHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps) Video format MP4 Magnification Up to 270 times (27 inch HDMI monitor) Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range Min. 5 cm Frame Rate Max. 120fps Video interface HDMI Storage microSD card (up to 64 GB) Power source 5 V DC Light source 2 LEDs with the stand Stand size 20 x 18 x 32 cm Included 1x Andonstar AD407 Pro Digital Microscope 1x Metal stand with 2 LEDs 1x UV filter (already assembled in the lens) 1x IR remote 1x Switch cable 1x Power adapter 1x Wrench 2x Metal clips 1x HDMI cable 1x User manual Downloads User Manual Model Comparison AD407 AD407 Pro AD409 AD409 Pro-ES Screen size 7 inch (17.8 cm) 7 inch (17.8 cm) 10.1 inch (25.7 cm) 10.1 inch (25.7 cm) Image sensor 4 MP 4 MP 4 MP 4 MP Video output 2160p 2160p 2160p 2160p Interfaces HDMI HDMI USB, HDMI, WiFi USB, HDMI, WiFi Video format MP4 MP4 MP4 MP4 Magnification Up to 270x Up to 270x Up to 300x Up to 300x Photo resolution Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Photo format JPG JPG JPG JPG Focus distance Min. 5 cm Min. 5 cm Min. 5 cm Min. 5 cm Frame rate Max. 120f/s Max. 120f/s Max. 120f/s Max. 120f/s Storage microSD card microSD card microSD card microSD card PC support No No Windows Windows Mobile connection No No WiFi + Measurement WiFi + Measurement Power source 5 V DC 5 V DC 5 V DC 5 V DC Light source 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand Endoscope No No No Yes Stand size 20 x 12 x 19 cm 20 x 18 x 32 cm 18 x 20 x 30 cm 18 x 20 x 32 cm Weight 1.6 kg 2.1 kg 2.2 kg 2.5 kg Price €259.00€199.00 €289.00€229.00 €399.00€279.00 €449.00€299.00 https://www.elektor.com/cdn/shop/files/andonstar-ad407-pro-hdmi-digital-microscope-with-7-inch-lcd_remote.jpg?v=1698675824https://www.elektor.com/cdn/shop/files/andonstar-ad407-pro-hdmi-digital-microscope-with-7-inch-lcd_dimensions.jpg?v=1698675824,https://www.elektor.com/cdn/shop/files/andonstar-ad407-pro-hdmi-digital-microscope-with-7-inch-lcd.jpg?v=1698675824,https://www.elektor.com/cdn/shop/files/andonstar-ad407-pro-hdmi-digital-microscope-with-7-inch-lcd_stand.jpg?v=1700560064,https://www.elektor.com/cdn/shop/files/andonstar-ad407-pro-hdmi-digital-microscope-with-7-inch-lcd_comparison.jpg?v=1700560064,https://www.elektor.com/cdn/shop/files/andonstar-ad407-pro-hdmi-digital-microscope-with-7-inch-lcd_contents.jpg?v=1700560064https://www.elektor.com/products/andonstar-ad407-pro-7-hdmi-digital-microscope?variant=46907256406348 in stock 289.0 229.0 47 0 0 2 - 4 Werktage 46907297792332 Andonstar AD409 10.1" HDMI Digital Microscope Andonstar Trade Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > No Member Discount > Production & Repair Comparison Websites 019681 The Andonstar AD409 microscope is equipped with a 10.1-inch LCD display, giving you a wider viewing range, free your eyes from fatigue. Features 10.1 inch adjustable LCD display Adjustable metal stand & monitor Two metal fixed clips microSD card Capture & Recording Built-in adjustable LEDs HDMI/USB Software supported Specifications Screen size 10.1 inch (25.7 cm) Image sensor 4 MP Video output UHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps) Video format MP4 Magnification Up to 300 times (27 inch HDMI monitor) Photo resolution Max. 12 MP (4032x3024) Photo format JPG Focus range Min. 5 cm Frame Rate Max. 120fps Video interface HDMI Storage microSD card (up to 32 GB) PC support Windows, PC software with measurement Mobile phone, tablet terminal support Support WiFi connection and measurement Power source 5 V DC Light source 2 LEDs with the stand Stand size 18 x 20 x 30 cm Included 1x Andonstar AD409 Digital Microscope 1x Metal stand with 2 LEDs 1x UV filter (already assembled in the lens) 1x IR remote 1x Switch cable 1x Power adapter 1x HDMI cable 1x User manual Downloads User Manual Software Model Comparison AD407 AD407 Pro AD409 AD409 Pro-ES Screen size 7 inch (17.8 cm) 7 inch (17.8 cm) 10.1 inch (25.7 cm) 10.1 inch (25.7 cm) Image sensor 4 MP 4 MP 4 MP 4 MP Video output 2160p 2160p 2160p 2160p Interfaces HDMI HDMI USB, HDMI, WiFi USB, HDMI, WiFi Video format MP4 MP4 MP4 MP4 Magnification Up to 270x Up to 270x Up to 300x Up to 300x Photo resolution Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Max. 4032x3024 Photo format JPG JPG JPG JPG Focus distance Min. 5 cm Min. 5 cm Min. 5 cm Min. 5 cm Frame rate Max. 120f/s Max. 120f/s Max. 120f/s Max. 120f/s Storage microSD card microSD card microSD card microSD card PC support No No Windows Windows Mobile connection No No WiFi + Measurement WiFi + Measurement Power source 5 V DC 5 V DC 5 V DC 5 V DC Light source 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand 2 LEDs with the stand Endoscope No No No Yes Stand size 20 x 12 x 19 cm 20 x 18 x 32 cm 18 x 20 x 30 cm 18 x 20 x 32 cm Weight 1.6 kg 2.1 kg 2.2 kg 2.5 kg Price €259.00€199.00 €289.00€229.00 €399.00€279.00 €449.00€299.00 https://www.elektor.com/cdn/shop/files/andonstar-ad409-hdmi-digital-microscope-with-10-inch-lcd_front.jpg?v=1698675831https://www.elektor.com/cdn/shop/files/andonstar-ad409-hdmi-digital-microscope-with-10-inch-lcd_connections.jpg?v=1698675831,https://www.elektor.com/cdn/shop/files/andonstar-ad409-hdmi-digital-microscope-with-10-inch-lcd.jpg?v=1698675831,https://www.elektor.com/cdn/shop/files/andonstar-ad409-hdmi-digital-microscope-with-10-inch-lcd_angles.jpg?v=1700560105,https://www.elektor.com/cdn/shop/files/andonstar-ad409-hdmi-digital-microscope-with-10-inch-lcd_comparison.jpg?v=1700560104https://www.elektor.com/products/andonstar-ad409-10-1-hdmi-digital-microscope?variant=46907297792332 out of stock 399.0 279.0 0 0 0 nicht auf Lager 46907281408332 Andonstar AD409 Pro-ES 10.1" HDMI Digital Microscope (incl. Endoscope) Andonstar Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > NEW > No Member Discount > Production & Repair > Sale Comparison Websites,DE Comparison Websites,FR Comparison Websites 020427 The Andonstar AD409 Pro-ES is a digital microscope with an extra-high stand that is also equipped with an endoscope. The microscope allows clear observation of the sides of components, the inside of pipes, etc., enabling 360° observation without dead angles. The microscope also has a remote control that allows you to easily switch between the following image modes: two-lens, microscope and endoscope.FeaturesHigh-quality metal lens and focusing barrelProfessional HDMI digital microscope supports multiple output methodsSoldering Microscope with Pro Metal StandUnique UV filter design8 Levels adjustable LED LightsConvenient Wireless Remote ControlProfessional Measurement SoftwareSpecificationsScreen size10.1 inch (25.7 cm)Image sensor4 MPVideo outputUHD 2880x2160 (24fps)FHD 1920x1080 (60fps/30fps)HD 1280x720 (120fps)Video formatMP4MagnificationUp to 300 times (27 inch HDMI monitor)Photo resolutionMax. 12 MP (4032x3024)Photo formatJPGFocus rangeMin. 5 cmFrame RateMax. 120fpsVideo interfaceHDMIStoragemicroSD card (up to 64 GB)PC supportWindows, PC software with measurementMobile phone, tablet terminal supportSupport WiFi connection and measurementPower source5 V DCLight source2 LEDs with the standEndoscopeYesStand size18 x 20 x 32 cmIncluded1x Andonstar AD409 Pro-ES Digital Microscope1x Endoscope1x Metal stand with 2 LEDs1x UV filter (already assembled in the lens)1x IR remote1x Switch cable1x Power adapter1x Wrench2x Metal clips1x HDMI cable1x User manualDownloadsUser ManualSoftwareModel Comparison AD407AD407 ProAD409AD409 Pro-ESScreen size7 inch (17.8 cm)7 inch (17.8 cm)10.1 inch (25.7 cm)10.1 inch (25.7 cm)Image sensor4 MP4 MP4 MP4 MPVideo output2160p2160p2160p2160pInterfacesHDMIHDMIUSB, HDMI, WiFiUSB, HDMI, WiFiVideo formatMP4MP4MP4MP4MagnificationUp to 270xUp to 270xUp to 300xUp to 300xPhoto resolutionMax. 4032x3024Max. 4032x3024Max. 4032x3024Max. 4032x3024Photo formatJPGJPGJPGJPGFocus distanceMin. 5 cmMin. 5 cmMin. 5 cmMin. 5 cmFrame rateMax. 120f/sMax. 120f/sMax. 120f/sMax. 120f/sStoragemicroSD cardmicroSD cardmicroSD cardmicroSD cardPC supportNoNoWindowsWindowsMobile connectionNoNoWiFi + MeasurementWiFi + MeasurementPower source5 V DC5 V DC5 V DC5 V DCLight source2 LEDs with the stand2 LEDs with the stand2 LEDs with the stand2 LEDs with the standEndoscopeNoNoNoYesStand size20 x 12 x 19 cm20 x 18 x 32 cm18 x 20 x 30 cm18 x 20 x 32 cmWeight1.6 kg2.1 kg2.2 kg2.5 kgPrice€259.00€199.00€289.00€229.00€399.00€279.00€449.00€299.00 https://www.elektor.com/cdn/shop/files/andonstar-ad409-pro-es-hdmi-digital-microscope-with-10-inch-lcd.jpg?v=1700035598https://www.elektor.com/cdn/shop/files/andonstar-ad409-pro-es-hdmi-digital-microscope-with-10-inch-lcd_view.jpg?v=1700035598,https://www.elektor.com/cdn/shop/files/andonstar-ad409-pro-es-hdmi-digital-microscope-with-10-inch-lcd_modes.jpg?v=1700035598,https://www.elektor.com/cdn/shop/files/andonstar-ad409-pro-es-hdmi-digital-microscope-with-10-inch-lcd_comparison.jpg?v=1700035697,https://www.elektor.com/cdn/shop/files/andonstar-ad409-pro-es-hdmi-digital-microscope-with-10-inch-lcd_contents.jpg?v=1700035767https://www.elektor.com/products/andonstar-ad409-pro-es-10-1-hdmi-digital-microscope-incl-endoscope?variant=46907281408332 in stock 449.0 299.0 99 0 0 2 - 4 Werktage 46906968736076 Andonstar ADSM201 3" HDMI Digital Microscope Andonstar Trade Measuring Tools > Microscopes > No Member Discount > Production & Repair 018063 There are three ways to use this microscope:as stand alone monitor, watching ther enlarged views on the built-in LCDwith a PC connect via USB 2.0, in capture modewith an external stand-alone HDMI displayBesides that you can record pictures and/or video on an optional SD card.Normal mode without PC or HDMI displayMagnify & Capture (on memory card) & Playback (from card)HDMI display output modeVisual effect with HDMI is amazingMaximum resolution: 1920x1080USB 2.0 output modeMicroscope functions as Windows PC camera.Capture video or still.Maximum resolution: 1080x720FeaturesAmple working distance: 4-15 cmReasonable depth of fieldExclusive lens: reduce veiling glare and prevent from harm of smudging which produced in the process of solderingReal time imagery, no smear300 times magnification, 1920x1080p, 30fps, HDMI out and high quality non-interpolate Large CMOS sensorDigital zoom (4x)Metal stand, sturdy and durableUSB2.0, & HDMI | HD video & LCD3.0 Dual LED lamps (with own power supply)No driver needed: compatible with Windows (10 and earlier) and with Android (not compatible with OS X)SpecificationsImage sensor3 MegapixelsVideo output1080p Full HDVideo formatMOVPhoto formatJPEGFocus rangeManual focus from 10mm to 150mmFrame rateMax 30f/s under 600 Lus BrightnessMagnification ratio10x to 300xVideo-output interfaceHDMI, to 1080P monitor with HDMI-InStoragemicroSD card, up to 32 GB (not included)Power source5 V DCIncluded1x Digital Microscope Andonstar ADSM2011x Mini Metal stand base include 2 LEDs1x HDMI cable1x USB cable1x DC adapter https://www.elektor.com/cdn/shop/files/hdmi-digital-microscope.jpg?v=1702653274https://www.elektor.com/cdn/shop/files/adsm201-parts.jpg?v=1702653274,https://www.elektor.com/cdn/shop/files/andonstar-hdmi.png?v=1702653274https://www.elektor.com/products/andonstar-adsm201-3-hdmi-digital-microscope?variant=46906968736076 out of stock 199.95 159.95 0 0 0 nicht auf Lager 46906986299724 Andonstar ADSM302 5" HDMI Digital Microscope Andonstar Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > Microscopes > No Member Discount > Production & Repair > Sale Comparison Websites 018374 Features 5' adjustable LCD monitor with adjustable tilt angle High resolution video & photo capture Wide table with comfortable headroom Heavy-weight stable metal stand Tall lifting stand (26 cm) Smooth adjustment wheels for focus and height Buttons on the monitor + remote control AV, USB, HDMI outputs SD card storage <32 GB Specifications Image sensor 3 Megapixels HD Sensor Video output 1080p Full HD (via HDMI)720p (via PC) Video format Real time play via HDMI w/o recordingMJPEG recording via PC/Mac Software Magnification Up to 560 times (HDMI monitor 22') Photo resolution 12M (see pixel formats in following table) Photo format JPEG Focus range 5 to 22 cm Frame rate Up to 30 f/s under 600 Lux Brightness Video-output interface HDMI/AV Storage microSD card, up to 32 GB PC support Windows XP/7/8/10 PC software with measurementMacOS successfully tested under OSX with OBS see video below Power source 5 V DC Light source 2x LED with the stand Screen size 5 inch (12.7 cm) Stand size 20 x 12 x 26.5 cm Resolution Captured Photos 4032 x 3024 3648 x 2736 3264 x 2448 2592 x 1944 2048 x 1536 640 x 480 1920 x 1080 1280 x 960 1280 x 720* Videos 1920 x 1080 640 x 480* * (USB with software) Included 1x Andonstar ADSM302 digital microscope 1x Metal stand with 2 LEDs 1x USB cable 1x HDMI cable 1x Adapter 1x AI remote 1x Instructions Downloads User Manual Measurement software https://www.elektor.com/cdn/shop/files/hdmi-av-digital-microscope-andonstar-adsm302_lcd-flat.jpg?v=1698675851https://www.elektor.com/cdn/shop/files/hdmi-av-digital-microscope-andonstar-adsm302_lcd-top.jpg?v=1698675851,https://www.elektor.com/cdn/shop/files/hdmi-av-digital-microscope-andonstar-adsm302_lcd.jpg?v=1698675851,https://www.elektor.com/cdn/shop/files/hdmi-av-digital-microscope-andonstar-adsm302_contents.jpg?v=1700560039,https://www.elektor.com/cdn/shop/files/hdmi-av-digital-microscope-andonstar-adsm302_package.jpg?v=1700560039,https://www.elektor.com/cdn/shop/files/hdmi-av-digital-microscope-andonstar-adsm302_display.jpg?v=1700560039,https://www.elektor.com/cdn/shop/files/adsm302_microscope_pistil.png?v=1700560040,https://www.elektor.com/cdn/shop/files/adsm302_microscope_functions.png?v=1700560039,https://www.elektor.com/cdn/shop/files/adsm302_microscope_remote.png?v=1700560040,https://www.elektor.com/cdn/shop/files/adsm302_microscope_clockwork.png?v=1700560040,https://www.elektor.com/cdn/shop/files/adsm302_microscope_solder_u1.png?v=1700560040,https://www.elektor.com/cdn/shop/files/adsm302_microscope_monitor_1.png?v=1700560039https://www.elektor.com/products/andonstar-adsm302-5-hdmi-digital-microscope?variant=46906986299724 in stock 229.0 194.95 10 0 0 2 - 4 Werktage 46907292123468 Andonstar V160 USB Digital Microscope Andonstar Trade Measuring Tools > Microscopes > Production & Repair 017975 The Andonstar V160 is a microscope with a sturdy stand which ensures a stable image. In addition, everything is precisely adjustable. The desired field of view can be set with knobs on the stand, and the focus can be adjusted with a solid rotating ring on the camera body. Specifications DSP: High power Digital Image Monarch Processor Sensor: high-quality CMOS sensor, 2M pixel (hardware,no Interpolation) Resolution: 640x480, 1600x1200 Interface: USB 1.1 / USB 2.0 Frame rate: 30 frames/sec (When resolution at 640x480), 1600x1200 5 frames/sec Focal distance: 5-30 mm (when Focal distance infinity, the microscope as a webcam, can not magnify) Magnification: 200+ Diameter: 12 mm USB cable Length: about 165 cm USB cable color: black or transparent color (random) Lighting: 8x LED around the camera lens Connects as a USB webcam with any OS. No specific software required Works on Mac (see image 4) with standard Apple Photo Booth Many OSX apps like miXscope or Digital Viewer can be used Included 1x Digital Microscope Camera 1x Software CD (User manual included) 1x Metal big base Stand https://www.elektor.com/cdn/shop/files/andonstar-usb-microscope-v160.png?v=1698677975https://www.elektor.com/cdn/shop/files/20161219151642_andonstar-detail.jpg?v=1698677975,https://www.elektor.com/cdn/shop/files/20161219150000_andonstar160.jpg?v=1698677975,https://www.elektor.com/cdn/shop/files/mac-screen.jpg?v=1698677975https://www.elektor.com/products/andonstar-v160-usb-digital-microscope?variant=46907292123468 out of stock 69.95 0 0 6.9 nicht auf Lager 46907292614988 Anet 4540 Desktop CNC Router Machine Anet Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Etching & Milling > Measuring Tools > No Member Discount > Prototyping > Sale Comparison Websites 020260 With this CNC milling machine, you can easily and quickly engrave, cut and drill with the highest precision. This powerful and efficient 3-axis CNC router machine is great for hobbyists, makers, DIY enthusiasts and pro engineers. The easy-to-use machine is ideal for cutting and engraving wood, MDF, metal, plastic, acrylic, leather, PCB and other materials. Features 3-axis CNC controller Engraving, cutting and drilling Large working area (430 x 390 x 90 mm) 500 W high-power spindle GRBL control Easy to assemble (main components are already pre-assembled) Specifications Working area 430 x 390 x 90 mm (16.93 x 15.39 x 3.54') Power supply 48 V/10.4 A Power of spindle motor 500 W Speed of spindle motor 11,000 rpm Stepping motor 42 x 48 mm Limit switch X, Y, Z (both ends) Material 4040 Aluminum Emergency stop switch Yes Offline controller Yes Software GRBLcontrol (Candle), other GRBL-compatible Software Other feature Laser Engraving (laser module is not included) Supported systems Windows XP/7/8/10 Dimensions 650 x 532 x 320 mm (25.59 x 20.94 x 12.60') Weight 11.6 kg (25.6 pounds)   https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine.jpg?v=1698677991https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine_operate.jpg?v=1698677991,https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine_controller.jpg?v=1698677991,https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine_detail.jpg?v=1698677991,https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine_motors.jpg?v=1698677991,https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine_mechanical-parts.jpg?v=1698677991,https://www.elektor.com/cdn/shop/files/anet-4540-desktop-cnc-machine_tool-parts.jpg?v=1698677991https://www.elektor.com/products/anet-4540-desktop-cnc-router-machine?variant=46907292614988 in stock 899.0 599.0 6 0 0 2 - 4 Werktage 46907168227660 Anycubic Photon Mono X - UV Resin SLA 3D Printer Anycubic Trade 3D Printers > Bestsellers > Measuring Tools > No Member Discount > Production & Repair > Sale 019831 Features Safe Design: Pinter will be immediately shut off if the top cover has been removed. This feature is turned off by default. Anycubic Slicer Software: New features are added to the software. Supports up to 8x anti-aliasing: Fast slicing, Hollowing, Split Model, Text Paste. Fast Printing Speed: The time of exposure is as low as 1.5-2 seconds, and the max print speed is 60 mm/h, making printing speed 3x faster than the Photon. High Performance Z-axis: The Z-axis is supported by dual linear rails,stepper motor and clearance nut combination which dramatically improves stability while in motion and reduces the risk of layer shifting. New Matrix UV Light Source: High quality quartz lamp bead and new matrix design for uniform UV light energy. 4K monochrome LCD delivers high-quality prints Anycubic APP Remote Control: Remote control of print operations,monitor printing progress,adjust the print settings UV Cooling System: Cooling device for stable printing performance and longer service life. Large Build Volume: A large build area for your 3D-printed creations: 192 mm (L) x 120 mm (W) x 245 mm (H) 8.9″ 4K Monochrome LCD: Monochrome screens can last several thousand hours. Monochrome screens allow for very short layer exposure times for faster print times. Specifications System: ANYCUBIC Photon Mono X Operation: 3.5 inch Touch Screen Software: ANYCUBIC Photon workshop Connectivity: USB Technology: LCD-based SLA Light-source: high-quality filament(wavelength 405 nm) XY Res.: 0.050 mm 3840 x 2400 (4K) Z Axis Res.: 0.01 mm Layer Res.: 0.01-0.15 mm Printing Speed: Max 60 mm/h Rated Power: 120 W Printer Size: 270 mm (L) x 290 mm (W) x 475 mm (H) Build Volume: 192 mm (L) x 120 mm (W) x 245 mm (H) Material: 405 nm UV Resin Net Weight: ~10.75 kg Parts List User Manual SD-Card Tool set SD-Card Reader Scraper Resin Vat Platform Power Cord Service Card Wifi Antenna Glove https://www.elektor.com/cdn/shop/files/anycubic_photon_mono_x_uv_resin_sla_3d_printer.jpg?v=1698677997https://www.elektor.com/cdn/shop/files/anycubic_photon_mono_x_uv_resin_sla_3d_printer_front.jpg?v=1698677997,https://www.elektor.com/cdn/shop/files/anycubic_photon_mono_x_uv_resin_sla_3d_printer_side.jpg?v=1698677997,https://www.elektor.com/cdn/shop/files/anycubic_photon_mono_x_uv_resin_sla_3d_printer_back.jpg?v=1698677997,https://www.elektor.com/cdn/shop/files/anycubic_photon_mono_x_uv_resin_sla_3d_printer_internal.jpg?v=1698677997https://www.elektor.com/products/anycubic-photon-mono-x-uv-resin-sla-3d-printer?variant=46907168227660 in stock 589.0 489.0 3 0 0 2 - 4 Werktage 47318768451916 Aoyue 8486 Fume Extractor Elektor Trade Bestsellers > Measuring Tools > NEW > Prototyping > Soldering Accessories 020473 The Aoyue 8486 fume extractor utilizes 3 filters including HEPA and activated carbon beads for the max. extraction efficiency. It removes 97% of particles greater than 0.3 um. Easily position the fume extractor soldering hose exactly where you need it over the work. Dial in the perfect amount of fume extraction power using the large front panel readout and control dial. Aoyue 8486 redirects soldering smoke caused by burning flux and other fumes away from your face so you can breathe. Features Desktop fume extraction system with HEPA filter (high efficiency particulate air filter) for removing the dust particles and enhanced activated carbon filtration system. With actual carbon filter beads. Powerful suction, quiet operation. Electronic control panel with variable airflow adjustment. Sub-filters extend the life of main filters. Free standing arms. Arms can be bent as desired and maintain their shape after adjustment. Unit has mount holes so it can be attached to walls to free up desk space. Specifications Voltage input 220 V DC voltage 12 V Suction fan 3.59 m/s Suction power 18-100% HEPA filter H11 class Carbon filter Activated carbon 800 IV (cylinder type) Dimensions 184 x 184 x 152 mm (W x H x D) Weight 1.8 kg Included Main unit Flexible extractor tube Filter hood HEPA filter Activated carbon filter Sub air filter DC power brick Instruction manual https://www.elektor.com/cdn/shop/files/aoyue-8486-fume-extractor.jpg?v=1699464552https://www.elektor.com/products/aoyue-8486-fume-extractor?variant=47318768451916 in stock 179.95 32 0 0 2 - 4 Werktage 47310489583948 Ardi Display Shield for Arduino Uno SB Components Trade Arduino > Arduino Accessories > Arduino Shields > Bestsellers > Displays > Displays & LEDs > NEW 5055652927217 The Ardi Display Shield features a vibrant 2" IPS screen with a resolution of 240 x 320 pixels, providing sharp and crisp visuals for your projects. Whether you're working on a small-scale project or a complex prototype, this display shield ensures clear and vibrant display output.With 2 programmable buttons, you have the flexibility to create interactive experiences and user-friendly interfaces. Customize the buttons to trigger specific actions or navigate through menus effortlessly.The possibilities are endless, limited only by your imagination. In addition to the programmable buttons, the Ardi Display Shield also includes a 5-way joystick for intuitive control. With the joystick's SPI interface, you can easily navigate menus, scroll through options, and control various aspects of your Arduino project with precision and ease.Designed with compatibility and ease of use in mind, the Ardi Display Shield seamlessly integrates with the Arduino Uno board. Simply connect it to your Arduino Uno and unlock a world of possibilities for visual feedback, user interaction, and data visualization.FeaturesOnboard 2.0" TFT DisplayCompatible with 3.3 V/5 V MCU, Selection providedOnboard 5-Way Joystick allows better control-related projectsTwo programmable Buttons to add additional functionality to projectMounts directly onto ArdiPi, Ardi32 or other Arduino compatible boardsSpecificationsDisplay resolution: 240x320 pixelsPixel Pitch: 0.1275 x 0.1275 mmActive Area: 30.6 x 40.8 mmModule Size: 34.6 x 47.8 x 2.05 mmSPI InterfaceDisplay Colors: 65K colorsDrive IC: ST7789V2Viewing Direction: All-view the best image https://www.elektor.com/cdn/shop/files/Ardi-Display-Shield-for-Arduino-Uno.jpg?v=1712236516https://www.elektor.com/cdn/shop/files/Ardi-Display-Shield-for-Arduino-Uno_view.jpg?v=1712236526,https://www.elektor.com/cdn/shop/files/Ardi-Display-Shield-for-Arduino-Uno_back.jpg?v=1712236536https://www.elektor.com/products/ardi-display-shield-for-arduino-uno?variant=47310489583948 in stock 24.95 24 4.9 6.9 2 - 4 Werktage 47310489616716 Ardi Relay Shield for Arduino Uno SB Components Trade Arduino > Arduino Accessories > Arduino Shields > Bestsellers > NEW 5055652927194 Enhance your Arduino projects with the Ardi Relay Shield, a versatile 4-channel optoisolated relay board. Designed to handle AC (250 V, 7 AMP) and DC (30 V, 10 AMP) power, this shield empowers you to easily control a wide range of electrical devices.Equipped with four LED relay indicators, the Ardi Relay Shield provides visual feedback on the status of each relay, ensuring you stay informed and in control of your circuit. The shield also features four 3-pin screw terminals (NC, NO, COM) for convenient and secure connections.Designed in the Arduino form factor, this shield seamlessly integrates with your Arduino Uno, allowing you to expand its capabilities and create interactive projects. Whether you're automating home appliances, building intelligent systems, or working on industrial applications, the Ardi Relay Shield is the reliable choice for robust and efficient relay control.Features4-channel optoisolated relay so better electrical isolation between High and Low side voltage.4x Relay shield compatible with both 3.3 V and 5 V MCUOnboard 4 Status LED to indicate each relay ON/OFF StateHigh-quality relaysProvides NO/NC interfaces with Screw terminals.Mounts directly onto ArdiPi, Ardi32 or other Arduino compatible boardsSpecificationsMax Switching Voltage: 250 V AC/30 V DCMax Switching Current: 7 A/10 AMax Switching Power: 2770 VA/240 WFrequency: 1 HzInitial Contact Resistance: 50 mΩ max at 6 V DC/1 AOperate Time: 10ms maxRelease Time: 5ms maxLife Expectancy Electrical: 100,000 operations (rated load)Life Expectancy Mechanical: 10,000,000 operations (no load) https://www.elektor.com/cdn/shop/files/Ardi-Relay-Shield-for-Arduino-Uno.jpg?v=1712234330https://www.elektor.com/cdn/shop/files/Ardi-Relay-Shield-for-Arduino-Uno_view.jpg?v=1712234340,https://www.elektor.com/cdn/shop/files/Ardi-Relay-Shield-for-Arduino-Uno_back.jpg?v=1712234356https://www.elektor.com/products/ardi-relay-shield-for-arduino-uno?variant=47310489616716 in stock 12.95 25 4.9 6.9 2 - 4 Werktage 47310489682252 Ardi RFID Shield for Arduino Uno SB Components Trade Arduino > Arduino Accessories > Arduino Shields > Bestsellers > NEW 5055652927200 Designed with convenience and security in mind, the Ardi RFID Shield is based on the EM-18 module, operating at a frequency of 125 KHz. This shield allows you to easily integrate RFID (Radio Frequency Identification) technology into your projects, enabling seamless identification and access control systems.Equipped with a powerful 1-channel optoisolated relay, the Ardi RFID Shield offers a reliable switching solution with a maximum DC rating of 30 V and 10 A, as well as an AC rating of 250 V and 7 A. Whether you need to control lights, motors, or other high-power devices, this shield provides the necessary functionality.Additionally, the Ardi RFID Shield features an onboard buzzer that can be utilized for audio feedback, allowing for enhanced user interaction and system feedback. With the onboard 2-indication LEDs, you can easily monitor the status of RFID card detection, power supply, and relay activation, providing clear visual cues for your project's operation.Compatibility is key, and the Ardi RFID Shield ensures seamless integration with the Arduino Uno platform. Paired with a read-only RFID module, this shield opens up a world of possibilities for applications such as access control systems, attendance tracking, inventory management, and more.FeaturesOnboard 125 kHz EM18 RFID small, compact moduleOnboard High-quality relays Relay with Screw terminal and NO/NC interfacesShield compatible with both 3.3 V and 5 V MCUOnboard 3 LEDs power, relay ON/OFF State and RFID Scan statusMulti-tone Buzzer onboard for Audio alertsMounts directly onto ArdiPi, Ardi32 or other Arduino compatible boardsSpecificationsRFID operating Frequency: 125 kHzReading distance: 10 cm, depending on TAGIntegrated AntennaRelay Max Switching Voltage: 250 V AC/30 V DCRelay Max Switching Current: 7 A/10 A https://www.elektor.com/cdn/shop/files/Ardi-RFID-Shield-for-Arduino-Uno.jpg?v=1712232758https://www.elektor.com/cdn/shop/files/Ardi-RFID-Shield-for-Arduino-Uno_view.jpg?v=1712232763,https://www.elektor.com/cdn/shop/files/Ardi-RFID-Shield-for-Arduino-Uno_back.jpg?v=1712232773https://www.elektor.com/products/ardi-rfid-shield-for-arduino-uno?variant=47310489682252 in stock 24.95 24 4.9 6.9 2 - 4 Werktage 47310489780556 Ardi UHF Shield for Arduino Uno (EU/UK) SB Components Trade Arduino > Arduino Accessories > Arduino Shields > Bestsellers > NEW > Radio | SDR 5055652927231 Designed with cutting-edge technology, this shield brings the power of Ultra High Frequency (UHF) RFID to your fingertips.With the Ardi UHF Shield, you can effortlessly read up to an impressive 50 tags per second, allowing for fast and efficient data collection. The shield features an onboard UHF antenna, ensuring reliable and accurate tag detection even in challenging environments.Equipped with a high-performance 0.91" OLED display, the Ardi UHF Shield provides clear and concise visual feedback, making it easy to monitor and interact with the RFID readings. Whether you're tracking inventory, managing access control, or implementing a smart attendance system, this shield has you covered.With a remarkable 1-meter reading distance, the Ardi UHF Shield offers an extended range for capturing RFID data. Say goodbye to the limitations of proximity-based RFID systems and embrace the flexibility and convenience of a wider reading range.The shield provides read-write capabilities, allowing you to not only retrieve information from RFID tags but also update or modify data as needed. This versatility opens up a world of possibilities for advanced applications and custom solutions.FeaturesOnboard High-performance UHF RFID reader module24 hours x 365 days’ work normally0.91” OLED display for visual interaction with shieldMulti-tone Buzzer onboard for Audio alertsShield compatible with both 3.3 V and 5 V MCUMounts directly onto ArdiPi, Ardi32 or other Arduino compatible boardsSpecificationsOLED resolution 128x32 pixelsI²C Interface for OLEDUHF Frequency Range (EU/UK): 865.1-867.9 MHzUHF Module Type: Read/WriteProtocols Supported: EPCglobal UHF Class 1 Gen 2 / ISO 18000-6CReading Distance: 1 metersCan identify over 50 tags simultaneouslyCommunication interface: TTL UART Interface for UHFCommunication baud rate: 115200 bps (default and recommend) – 38400 bpsOperation current: 180 mA @ 3.5 V (26 dBm Output, 25°C), 110 mA @ 3.5 V (18 dBm Output, 25°C)Working humidity <95% (+25°C)Heat-dissipating method Air cooling(no need out install cooling fin)Tags storage capacity: 200 pcs tags @ 96 bit EPCOutput power: 18-26 dBmOutput power accuracy: +/-1 dBTags RSSI support https://www.elektor.com/cdn/shop/files/Ardi-UHF-Shield-for-Arduino-Uno.jpg?v=1712232119https://www.elektor.com/cdn/shop/files/Ardi-UHF-Shield-for-Arduino-Uno_view.jpg?v=1712232128,https://www.elektor.com/cdn/shop/files/Ardi-UHF-Shield-for-Arduino-Uno_back.jpg?v=1712232142https://www.elektor.com/products/ardi-uhf-shield-for-arduino-uno-eu-uk?variant=47310489780556 in stock 129.95 25 0 0 2 - 4 Werktage 47310489911628 Ardi32 - Uno R3 Board based on ESP32-S3-WROOM-1 SB Components Trade Arduino > Arduino Accessories > Bestsellers > ESP > ESP32 > NEW 5055652926647 Ardi32 is the ultimate Arduino Uno alternative packed with powerful specs and exciting features in the Arduino Uno form factor. Ardi32 is powered by the latest ESP32-S3-WROOM-1. The built-in Wi-Fi and Bluetooth connectivity makes the board ideal for IoT projects or projects requiring wireless communication.FeaturesPowered by powerful ESP32-S3-WROOM-1 module with inbuild WiFi and BLE support.Arduino Uno form factor, so you can connect 3.3 V compatible Arduino shieldsSD card slot for storage and data transferThe facility of USB-C interface for programming and to the power boardBoot and Reset buttons are available to operate in various modes.Multifunction GPIO breakout supporting general I/O, UART, I²C, SPI, ADC & PWM functions.Multi-tune Buzzer to add audio alert into the projectMulti-platform support like Arduino IDE, Espressif IDF, and MicroPython/CircuitPythonComes with HID support, so the device can simulate a mouse or keyboardSpecificationsESP32-S3 series of SoCs having Xtensa dual-core 32-bit LX7 microprocessor4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE)Flash up to 16 MB, PSRAM up to 8 MBBoard supply 5 V and GPIO pins operating voltage 3.3 V22 multipurpose GPIOs breakout in Arduino style for easy peripheral and shield interfacingI²C, SPI, and UART communications protocol supportCross-platform development and multiple programming language support https://www.elektor.com/cdn/shop/files/Ardi32-Uno-R3-Board.jpg?v=1712229947https://www.elektor.com/cdn/shop/files/Ardi32-Uno-R3-Board_view.jpg?v=1712229954https://www.elektor.com/products/ardi32-uno-r3-board-based-on-esp32-s3-wroom-1?variant=47310489911628 in stock 32.95 25 4.9 6.9 2 - 4 Werktage 47310489944396 ArdiPi - Uno R3 Board based on Raspberry Pi Pico W SB Components Trade Arduino > Arduino Accessories > Bestsellers > NEW > Pico RP2040 > Raspberry Pi 5055652926630 ArdiPi is the ultimate Arduino Uno alternative packed with powerful specs and exciting features in the Arduino Uno form factor. You can enjoy a low-cost solution with access to the largest support communities for Raspberry Pi.ArdiPi variant is powered by Raspberry Pi Pico W. The built-in Wi-Fi and Bluetooth connectivity makes the board ideal for IoT projects or projects requiring wireless communication.FeaturesArduino Uno form factor, so you can connect 3.3 V compatible Arduino shieldsSD card slot for storage and data transferDrag-and-drop programming using mass storage over USBMultifunction GPIO breakout supporting general I/O, UART, I²C, SPI, ADC & PWM functions.Multi-tune Buzzer to add audio alert into the projectSWD pins breakout for serial debuggingMulti-platform support like Arduino IDE, MicroPython, and CircuitPython.Comes with HID support, so the device can simulate a mouse or keyboardSpecificationsPowered by RP2040 microcontroller which is a dual-core Arm Cortex-M0+ processor, 2 MB of onboard flash storage, 264 kB of RAMOn-board single-band 2.4 GHz wireless interfaces (802.11n) for WiFi and Bluetooth 5 (LE)WPA3 & Soft access point supporting up to four clientsOperating voltage of pins 3.3 V and board supply 5 V25 Multipurpose GPIOs breakout in Arduino style for easy peripheral interfacingI²C, SPI, and UART communications protocol support2 MB of onboard Flash memoryCross-platform development and multiple programming language support https://www.elektor.com/cdn/shop/files/ArdiPi-Uno-R3-Board.jpg?v=1712227627https://www.elektor.com/cdn/shop/files/ArdiPi-Uno-R3-Board_view.jpg?v=1712227634https://www.elektor.com/products/ardipi-uno-r3-board-based-on-raspberry-pi-pico-w?variant=47310489944396 in stock 24.95 25 4.9 6.9 2 - 4 Werktage 46907246805324 Arduboy FX Elektor Trade Arduino > Arduino Accessories > Bestsellers > Fun Electronics > Platforms 114992444 Arduboy is a miniture game development system the size of a credit card based on the popular open source Arduino platform. Learn to program/code with lots of tutorials and an active community of developers, develop and share your own games using Arduino software via the USB-Cable. Use your PC/Mac/Linux machine to download over 200 unique games created by members of the Arduboy Community.FeaturesProcessor: ATmega32u4 (same as Arduino Leonardo & Micro)Memory: 32 KB Flash, 2.5 KB RAM, 1 KB EEPROMInputs: 6 Momentary Tactile ButtonsOutputs: 128 x 64 1-bit OLED, 4 Ch. Piezo Speaker & Blinky LEDBattery: 180 mAh Thin-Film Lithium PolymerConnectivity: Micro-USB 2.0 with built-in HID profileProgramming: Arduino IDE, Arduboy Game Loader, GCC & AVRDudeOpen source gamingAnyone can make games for the Arduboy! Free online tutorials guide you through a step by step process on how to develop your own software! There are already plenty of examples to learn from. Ever wanted to create a level or map for your favorite game, or make your favorite character jump higher? Now is your chance!Super retroDesigned to remind you of a more simple time in the world of gaming, the Arduboy brings true 8-bit gaming into the 21st century with style. The black and white screen invites you to involve your imagination once again while gaming.Durable constructionA polycarbonate front, ultra thin circuit board, and stamped aluminum metal back is the ultimate combination. A rechargeable lithium polymer battery provides over 8 hours of battery life, and the same cable you use to charge can be used to upload new games! At only 5 mm thick, Arduboy can live in your pocket (or even wallet) and is thinner than nearly any mobile phone!DownloadsSchematicsGitHubDocumentation https://www.elektor.com/cdn/shop/files/arduboy-fx.jpg?v=1689091927https://www.elektor.com/cdn/shop/files/arduboy-fx_back.jpg?v=1696854379https://www.elektor.com/products/arduboy-fx?variant=46907246805324 in stock 74.95 36 0 6.9 2 - 4 Werktage 46907231797580 Arduino & Co - Measure, Control, and Hack Elektor Publishing Books Arduino > Arduino Books > Bestsellers > Books > NEW > Print Books > Raspberry Pi | Arduino | ESP Elektor Print Book 9783895765155 Clever Tricks with ATmega328 Pro Mini BoardsWith a simple Pro Mini board and a few other components, projects that 20 or 30 years ago were unthinkable (or would have cost a small fortune) are realized easily and affordably in this book: From simple LED effects to a full battery charging and testing station that will put a rechargeable through its paces, there’s something for everyone.All the projects are based on the ATmega328 microcontroller, which offers endless measuring, switching, and control options with its 20 input and output lines. For example, with a 7-segment display and a few resistors, you can build a voltmeter or an NTC-based thermometer. The Arduino platform offers the perfect development environment for programming this range of boards.Besides these very practical projects, the book also provides the necessary knowledge for you to create projects based on your own ideas. How to measure, and what? Which transistor is suitable for switching a certain load? When is it better to use an IC? How do you switch mains voltage? Even LilyPad-based battery-operated projects are discussed in detail, as well as many different motors, from simple DC motors to stepper motors.Sensors are another exciting topic: For example, a simple infrared receiver that can give disused remote controls a new lease on life controlling your home, and a tiny component that can actually measure the difference in air pressure between floor and table height! https://www.elektor.com/cdn/shop/files/arduino-and-co.png?v=1689091254https://www.elektor.com/products/arduino-and-co-measure-control-and-hack?variant=46907231797580 in stock 34.95 81 4.9 6.9 2 - 4 Werktage 46907231895884 Arduino & Co - Measure, Control, and Hack (E-book) Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-46907231895884-has-digital-downloads 978-3-89576-516-2 Clever Tricks with ATmega328 Pro Mini BoardsWith a simple Pro Mini board and a few other components, projects that 20 or 30 years ago were unthinkable (or would have cost a small fortune) are realized easily and affordably in this book: From simple LED effects to a full battery charging and testing station that will put a rechargeable through its paces, there’s something for everyone.All the projects are based on the ATmega328 microcontroller, which offers endless measuring, switching, and control options with its 20 input and output lines. For example, with a 7-segment display and a few resistors, you can build a voltmeter or an NTC-based thermometer. The Arduino platform offers the perfect development environment for programming this range of boards.Besides these very practical projects, the book also provides the necessary knowledge for you to create projects based on your own ideas. How to measure, and what? Which transistor is suitable for switching a certain load? When is it better to use an IC? How do you switch mains voltage? Even LilyPad-based battery-operated projects are discussed in detail, as well as many different motors, from simple DC motors to stepper motors.Sensors are another exciting topic: For example, a simple infrared receiver that can give disused remote controls a new lease on life controlling your home, and a tiny component that can actually measure the difference in air pressure between floor and table height! https://www.elektor.com/cdn/shop/files/arduino-and-co-pdf.png?v=1689091268https://www.elektor.com/products/arduino-and-co-measure-control-and-hack-e-book?variant=46907231895884 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 47571232850252 Arduino - Circuits & Projects Guide Elektor Publishing Books Arduino Books > Bestsellers > No Member Discount > Raspberry Pi | Arduino | ESP 9781907920257 Two reasons can be identified for the immense success of the Arduino platform. First, the cheap, ready to go processor board greatly simplifies the introduction to hardware. The second success factor is the free and open-source programming suite that does not require an installation procedure.Simple entry-level examples ensure rapid successes. Complex selection procedures for parameters like the microprocessor version or interface settings are not required. The first sample programs can be uploaded to the Arduino board, and tested, in a matter of minutes.The Arduino user is supported by an array of software libraries. However, the daily increasing volume of libraries poses initial problems to the newcomer, and the way ahead may be uncertain after a few entry-level examples. In many cases, detailed descriptions are missing, and poorly described projects tend to confuse rather than elucidate. Clear guidance and a single motto are missing, usually owing to the projects having been created by several different persons?all with different aims in mind.This book represents a different approach. All projects are presented in a systematical manner, guiding into various theme areas. In the coverage of must-know theory great attention is given to practical directions users can absorb, including essential programming techniques like A/D conversion, timers and interrupts?all contained in the hands-on projects. In this way readers of the book create running lights, a wakeup light, fully functional voltmeters, precision digital thermometers, clocks of many varieties, reaction speed meters, or mouse controlled robotic arms. While actively working on these projects the reader gets to truly comprehend and master the basics of the underlying controller technology. https://www.elektor.com/cdn/shop/files/arduino-circuits-and-projects-guide_1.png?v=1705319170https://www.elektor.com/products/arduino-circuits-projects-guide?variant=47571232850252 in stock 39.95 65 4.9 6.9 2 - 4 Werktage 46906991673676 Arduino 8-bit Sound Generation (E-book) Elektor Digital E-books Arduino > Arduino Books > Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46906991673676-has-digital-downloads David Cuartielles (1974, Zaragoza, Spanje) is een telecommunicatie-ingenieur. In 2000 ontwikkelde hij de net-art The Wake Interactive, een web-versie van Finnegans Wake, de klassieker van James Joyce, die hem naar K3 leidde, de kunst- en communicatieschool van de Malmö Universiteit, Zweden. Co-auteur van het bekende Arduino-platform voor elektronische prototyping sinds 2005, is David doorgegaan met het ontwikkelen van nieuwe boards en leermiddelen die het toepassingsgebied van Arduino’s uitbreiden. Als onderdeel van zijn outreach-activiteiten, werkt David samen met Elektor door het leveren van didactisch gedreven artikelen. Arduinonext is een initiatief van een team specialisten op het gebied van elektronica en microcontrollers met als doel iedereen te helpen die zich in de wereld van de technologie wil begeven en het bekende Arduino-platform wil gebruiken om de volgende stap in de elektronica te zetten. We streven ernaar om u de nodige kennis en ervaring bij te brengen voor het ontwikkelen van uw eigen elektronica toepassingen, interactie met de omgeving, het meten van fysieke parameters, het verwerken ervan en het uitvoeren van de nodige controle acties. Dit is de eerste titel in de ‘Hands-On’ serie waarin mede-oprichter van het Arduino-platform, David Cuartielles, het programmeren van het board introduceert, en demonstreert hoe je een 8-bit Sound Generator. https://www.elektor.com/cdn/shop/files/af_libreto_arduino_ebook_page_1-1.jpg?v=1689085053https://www.elektor.com/cdn/shop/files/af_libreto_arduino_ebook_page_26-1.jpg?v=1696849384https://www.elektor.com/products/arduino-8-bit-sound-generation-e-book?variant=46906991673676 in stock 4.95 0 4.9 6.9 2 - 4 Werktage 46907225866572 Arduino Braccio ++ RP2040 powered Robot Arm Arduino Trade Arduino Robots > Comparison Websites DE > Comparison Websites FR > Education > Pico RP2040 > Platforms > Raspberry Pi > Robotics Comparison Websites 7630049203259 The next evolution of the Tinkerkit Braccio robot, Arduino Braccio ++ is a robotic arm designed solely for higher education, including engineering schools and university institutes of technology – or even advanced high school and college students studying the sciences, industrial science or technology. Arduino Braccio ++ is fully optimized and can be assembled in several ways for multiple tasks, such as moving objects, mounting a camera and tracking your movements, or attaching a solar panel and tracking the movement of the sun. Its uses are almost limitless. Students will learn real life applications of physical concepts through lifting, placing, and rotating an item. These concepts include motions, forces, torque, gear ratios, stability, and weight of payload. Arduino Braccio ++ offers a multitude of expansive possibilities from the very outset, including a new Braccio Carrier with LCD screen, new RS485 servo motors, and a totally enhanced experience. The main material used to build the Arduino Braccio ++ structure is a recycled and eco-friendly plastic called EcoAllene, a plastic material obtained from recycled polylaminate found in food cartons, meaning that all the plastic parts of Arduino Braccio ++ are sustainable and 100% recyclable. Downloads Braccio Carrier https://www.elektor.com/cdn/shop/files/arduino-braccio-rp2040-powered-robot-arm.jpg?v=1698678075https://www.elektor.com/cdn/shop/files/arduino-braccio-rp2040-powered-robot-arm_package.jpg?v=1698678075,https://www.elektor.com/cdn/shop/files/arduino-braccio-rp2040-powered-robot-arm_contents.jpg?v=1698678075,https://www.elektor.com/cdn/shop/files/arduino-braccio-rp2040-powered-robot-arm_board.jpg?v=1698678075,https://www.elektor.com/cdn/shop/files/arduino-braccio-rp2040-powered-robot-arm_box.jpg?v=1698678075https://www.elektor.com/products/arduino-braccio-rp2040-powered-robot-arm?variant=46907225866572 out of stock 499.0 0 0 0 nicht auf Lager 47318724837708 Arduino Compilation (EN) | E-book Elektor Digital E-books Bestsellers > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-47318724837708-has-digital-downloads Arduino Compilation (EN) | E-book https://www.elektor.com/cdn/shop/files/arduino-compilation-pdf.jpg?v=1699463217https://www.elektor.com/cdn/shop/files/arduino_compilatie_uk_sku_17164.png?v=1699543409https://www.elektor.com/products/arduino-compilation-en-e-book?variant=47318724837708 in stock 9.5 0 4.9 6.9 2 - 4 Werktage 47318724641100 Arduino Compilation Mini (EN) | E-book Elektor Digital E-books Arduino Books > Bestsellers > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-47318724641100-has-digital-downloads - Contents: 3D Pad: Touchless Gesture Control Interface (Jean-Noël Lefebvre) My First Shield :) (Jens Nickel) Arduino is a Tool (Clemens Valens) Arduino Software Development with Atmel Studio (Wolfram Pioch) Arduino Yún (Clemens Valens) https://www.elektor.com/cdn/shop/files/arduinoselectmini_en.png?v=1699463202https://www.elektor.com/products/select-arduino-mini?variant=47318724641100 in stock 4.95 0 4.9 6.9 2 - 4 Werktage 46907189330252 Arduino Due with Headers Arduino Trade Arduino > Arduino Boards > Bestsellers 9783645651936 The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it with an AC-to-DC adapter or battery to get started. The Due is compatible with all Arduino shields that work at 3.3V and are compliant with the 1.0 Arduino pinout. The Due follows the 1.0 pinout: TWI: SDA and SCL pins that are near to the AREF pin. IOREF: allows an attached shield with the proper configuration to adapt to the voltage provided by the board. This enables shield compatibility with a 3.3V board like the Due and AVR-based boards which operate at 5V. An unconnected pin, reserved for future use. Operating Voltage 3.3 V Input Voltage 7 V - 12 V Digital I/O 54 Analog Input Pins 12 Analog Output Pins 2 (DAC) Total DC Output Current on all I/O Lines 130 mA DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 800 mA DC Current for 5 V Pin 800 mA Flash Memory 512 KB all available for the user applications SRAM 96 KB Clock Speed 84 MHz Length 101.52 mm Width 53.3 mm Weight 36 g Please note: Unlike most Arduino boards, the Arduino Due board runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. https://www.elektor.com/cdn/shop/files/arduino-due-with-headers.jpg?v=1698678088https://www.elektor.com/cdn/shop/files/arduino-due-with-headers_back.jpg?v=1698678088,https://www.elektor.com/cdn/shop/files/arduino-due-with-headers_package.jpg?v=1698678088https://www.elektor.com/products/arduino-due-with-headers?variant=46907189330252 in stock 44.95 33 4.9 6.9 2 - 4 Werktage 46907190575436 Arduino Ethernet Shield 2 Arduino Trade Arduino > Arduino Boards > Bestsellers 8058333490328 As always with Arduino, every element of the platform – hardware, software, and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, every day. The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the Shield. The Ethernet Shield 2 connects to an Arduino Board using long wire-wrap headers extending through the Shield. This keeps the pin layout intact and allows another Shield to be stacked on top of it. The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO Board. The Ethernet Shield 2 has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled. There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard micro-SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the Shield contained a full-size SD card slot; this is not supported. The Shield also includes a reset controller, to ensure that the W5500 Ethernet module is properly reset on power-up. Previous revisions of the Shield were not compatible with the Mega and needed to be manually reset after power-up. https://www.elektor.com/cdn/shop/files/arduino_ethernet_shield_2_-_overview.jpg?v=1698678093https://www.elektor.com/cdn/shop/files/arduino_ethernet_shield_2_-_bottom.jpg?v=1698678093,https://www.elektor.com/cdn/shop/files/arduino_ethernet_shield_2_-_package.jpg?v=1698678093https://www.elektor.com/products/arduino-ethernet-shield-2?variant=46907190575436 in stock 34.95 5 4.9 6.9 2 - 4 Werktage 47743987286348 Arduino for Radio Amateur Applications Elektor Publishing Books Arduino > Arduino Books > Bestsellers > Books > Books | Audio & RF > NEW 9783895766015 Program and build Arduino-based ham station utilities, tools, and instrumentsIn addition to a detailed introduction to the exciting world of the Arduino microcontroller and its many variants, this book introduces you to the shields, modules, and components you can connect to the Arduino. Many of these components are discussed in detail and used in the projects included in this book to help you understand how these components can be incorporated into your own Arduino projects. Emphasis has been placed on designing and creating a wide range of amateur radio-related projects that can easily be built in just a few days.This book is written for ham radio operators and Arduino enthusiasts of all skill levels, and includes discussions about the tools, construction methods, and troubleshooting techniques used in creating amateur radio-related Arduino projects. This book teaches you how to create feature-rich Arduino-based projects, with the goal of helping you to advance beyond this book, and design and build your own ham radio Arduino projects.In addition, this book describes in detail the design, construction, programming, and operation of the following projects:CW Beacon and Foxhunt KeyerMini Weather StationRF Probe with LED Bar GraphDTMF Tone EncoderDTMF Tone DecoderWaveform GeneratorAuto Power On/OffBluetooth CW KeyerStation Power MonitorAC Current MonitorThis book assumes a basic knowledge of electronics and circuit construction. Basic knowledge of how to program the Arduino using its IDE will also be beneficial. https://www.elektor.com/cdn/shop/files/Arduino-for-Radio-Amateur-Applications.png?v=1710166640https://www.elektor.com/products/arduino-for-radio-amateur-applications?variant=47743987286348 in stock 34.95 159 4.9 6.9 2 - 4 Werktage 47743990858060 Arduino for Radio Amateur Applications (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-47743990858060-has-digital-downloads Program and build Arduino-based ham station utilities, tools, and instrumentsIn addition to a detailed introduction to the exciting world of the Arduino microcontroller and its many variants, this book introduces you to the shields, modules, and components you can connect to the Arduino. Many of these components are discussed in detail and used in the projects included in this book to help you understand how these components can be incorporated into your own Arduino projects. Emphasis has been placed on designing and creating a wide range of amateur radio-related projects that can easily be built in just a few days.This book is written for ham radio operators and Arduino enthusiasts of all skill levels, and includes discussions about the tools, construction methods, and troubleshooting techniques used in creating amateur radio-related Arduino projects. This book teaches you how to create feature-rich Arduino-based projects, with the goal of helping you to advance beyond this book, and design and build your own ham radio Arduino projects.In addition, this book describes in detail the design, construction, programming, and operation of the following projects:CW Beacon and Foxhunt KeyerMini Weather StationRF Probe with LED Bar GraphDTMF Tone EncoderDTMF Tone DecoderWaveform GeneratorAuto Power On/OffBluetooth CW KeyerStation Power MonitorAC Current MonitorThis book assumes a basic knowledge of electronics and circuit construction. Basic knowledge of how to program the Arduino using its IDE will also be beneficial. https://www.elektor.com/cdn/shop/files/Arduino-for-Radio-Amateur-Applications-PDF.png?v=1710166674https://www.elektor.com/products/arduino-for-radio-amateur-applications-e-book?variant=47743990858060 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 47310490239308 Arduino Giga Display Shield Arduino Trade Arduino Shields > Bestsellers > Displays & LEDs 7630049203419 The Giga Display Shield is a touch screen solution designed to effortlessly deploy graphic interfaces in your projects. Leveraging the new pin header connector in the middle of Giga R1 WiFi, this shield offers seamless integration and enhanced functionalities. With the Giga Display Shield, you gain access to an array of features, including a digital microphone, 6-axis IMU, and Arducam connector. These added capabilities allow you to fully utilize the other 54 available pins, making it incredibly convenient to create handheld devices or dashboards to control your project. Specifications Display KD040WVFID026-01-C025A Size 3.97” Resolution 480x800 RGB Color 16.7M Touch Mode Five points and Gestures Interface I²C Sensors IMU BMI270 Microphone MP34DT06JTR Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/Arduino-Giga-Display-Shield.jpg?v=1700133402https://www.elektor.com/cdn/shop/files/Arduino-Giga-Display-Shield_view.jpg?v=1700133411,https://www.elektor.com/cdn/shop/files/Arduino-Giga-Display-Shield_back.jpg?v=1700133420,https://www.elektor.com/cdn/shop/files/Arduino-Giga-Display-Shield_package.jpg?v=1700133427https://www.elektor.com/products/arduino-giga-display-shield?variant=47310490239308 in stock 84.95 18 0 6.9 2 - 4 Werktage 46907283374412 Arduino Giga R1 WiFi Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR Comparison Websites 7630049203266 The Arduino Giga R1 WiFi brings the power of the STM32H7 to the same form factor as the popular Mega and Due, being the first Mega board to include onboard Wi-Fi and Bluetooth connectivity. The board provides 76 digital inputs/outputs (12 with PWM capability), 14 analog inputs and 2 analog outputs (DAC) all easily accessible via pin headers. The STM32 microprocessor with dual-core Cortex-M7 and Cortex-M4, together with onboard memory and audio jack enables you to perform machine learning and signal processing on the edge. Microcontroller (STM32H747XI) This dual core 32-bits microcontroller allows you have two brain talking to each other (a Cortex-M7 at 480 MHz and a Cortex-M4 at 240 MHz) you can even run micropython in one and Arduino in the other. Wireless communication (Murata 1DX) Whether you prefer Wi-Fi or Bluetooth, the Giga R1 WiFi got you covered. You can even quickly connect to the Arduino IoT Cloud and keep track of your project remotely. And if you are concerned about the security of the communication, the ATECC608A keeps everything under control. Hardware ports and communication Following the legacy of the Arduino Mega and the Arduino Due, the Giga R1 WiFi has 4x UARTs (hardware serial ports), 3x I²C ports (1 more than its predecessors), 2x SPI ports (1 more than its predecessors), 1x FDCAN. GPIOs and extra pins By keeping the same form factor of the Mega and the Due, you can easily adapt your custom made shields to the Giga R1 WiFi (remember this board works at 3.3 V though!). Also, additional headers have been added so that the total number of GPIO pins is now 76, and two new pins have been added: a VRTC so you can connect a battery to keep the RTC running while the board is off and an OFF pin so you can shut down the board. Connectors The Giga R1 WiFi has extra connectors on board which will facilitate the creation of your project without any extra hardware. This board has: USB-A connector suitable for hosting USB sticks, other mass storage devices and HID devices such as keyboard or mouse. 3.5 mm input-output jack connected to DAC0, DAC1 and A7. USB-C to power and program the board, as well as simulate an HID device such as mouse or keyboard. Jtag connector, 2x5 1.27 mm. 20-pin Arducam camera connector. Higher voltage support: In comparison with its predecessors that support up to 12 V, the Giga R1 WiFi can handle a range of 6 to 24 V. Specifications Microcontroller STM32H747XI dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet) Radio Module Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth (datasheet) Secure Element ATECC608A-MAHDA-T (datasheet) USB USB-C Programming Port / HID USB-A Host (enable with PA_15) Pins Digital I/O pins 76 Analog input pins 12 DAC 2 (DAC0/DAC1) PWM pins 12 Misc VRT & OFF pin Communication UART 4x I²C 3x SPI 2x CAN Yes (requires an external transceiver) Connectors Camera I²C + D54-D67 Display D1N, D0N, D1P, D0P, CKN, CKP + D68-D75 Audio Jack DAC0, DAC1, A7 Power Circuit operating voltage 3.3 V Input voltage (VIN) 6-24 V DC Current per I/O Pin 8 mA Clock Speed Cortex-M7 480 MHz Cortex-M4 240 MHz Memory STM32H747XI 2 MB Flash, 1 MB RAM Dimensions 53 x 101 mm Downloads Datasheet Schematics Pinout https://www.elektor.com/cdn/shop/files/arduino-giga-r1-wifi.jpg?v=1698678105https://www.elektor.com/cdn/shop/files/arduino-giga-r1-wifi_side.jpg?v=1698678105,https://www.elektor.com/cdn/shop/files/arduino-giga-r1-wifi_back.jpg?v=1698678105,https://www.elektor.com/cdn/shop/files/arduino-giga-r1-wifi_contents.jpg?v=1698678105,https://www.elektor.com/cdn/shop/files/arduino-giga-r1-wifi_package.jpg?v=1698678105https://www.elektor.com/products/arduino-giga-r1-wifi?variant=46907283374412 in stock 89.95 29 0 6.9 2 - 4 Werktage 46907190378828 Arduino Leonardo with Headers Arduino Trade Arduino > Arduino Boards > Bestsellers 8058333491141 The Leonardo differs from all preceding boards in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Leonardo to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port. Microcontroller ATMega4809 Operating Voltage 5 V Input Voltage 7 V - 12 V Analog Input Pins 12 PWM Pins 7 DC I/O Pin 20 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB of which 4 KB used by the bootloader SRAM 2.5 KB EEPROM 1 KB Clock Speed 16 MHz Length 68.6 mm Width 53.3 mm Weight 20 g https://www.elektor.com/cdn/shop/files/arduino_leonardo_with_headers_-_overview.jpg?v=1698678117https://www.elektor.com/cdn/shop/files/arduino_leonardo_with_headers_-_bottom.jpg?v=1698678117https://www.elektor.com/products/arduino-leonardo-with-headers?variant=46907190378828 in stock 21.95 5 4.9 6.9 2 - 4 Werktage 46907244020044 Arduino Make-Your-Uno Kit Arduino Trade Arduino > Arduino Kits > Bestsellers > Components > Kits 7630049203433 Learn the basics of electronics by assembling manually your Arduino Uno, become familiar with soldering by mounting every single component, and then unleash your creativity with the only kit that becomes a synth! The Arduino Make-Your-Uno kit is really the best way to learn how to solder. And when you are done, the packaging allows you to build a synth and make your music. A kit with all the components to build your very own Arduino Uno and audio synthesizer shield. The Make-Your-Uno kit comes with a complete set of instructions in a dedicated content platform. This includes video material, a 3D interactive viewer for following detailed instructions, and how to program your board once it is finished. This kit contains: Arduino Make-Your-Uno 1x Make-Your-Uno PCB 1x USB C Serial adapter Board 7x Resistors 1k Ohm 2x Resistors 10k Ohm 2x Resistors 1M Ohm 1x Diode (1N4007) 1x 16 MHz Crystal 4x Yellow LEDs 1x Green LED 1x Push-Button 1x MOSFET 1x LDO (3.3 V) 1x LDO (5 V) 3x Ceramic capacitors (22pF) 3x Electrolytic capacitors (47uF) 7x Polyester capacitors (100nF) 1x Socket for ATMega 328p 2x I/O Connectors 1x Connector header 6 pins 1x Barrel jack connector 1x ATmega 328p Microcontroller Arduino Audio Synth 1x Audio Synth PCB 1x Resistor 100k Ohm 1x Resistor 10 Ohm 1x Audio amplifier (LM386) 1x Ceramic capacitors (47nF) 1x Electrolytic capacitors (47uF) 1x Electrolytic capacitors (220uF) 1x Polyester capacitor (100nF) 4x connectors pin header 6x potentiometer 10k Ohm with plastic knobs Spare parts 2x Electrolytic capacitors (47uF) 2x Polyester capacitor (100nF) 2x Ceramic capacitors (22pF) 1x Push-Button 1x Yellow LEDs 1x Green LED Mechanical parts 5x Spacers 12 mm 11x Spacers 6 mm 5x screw nuts 2x screws 12 mm https://www.elektor.com/cdn/shop/files/arduino-make-your-uno-kit.jpg?v=1698678130https://www.elektor.com/cdn/shop/files/arduino-make-your-uno-kit_buttons.jpg?v=1698678130,https://www.elektor.com/cdn/shop/files/arduino-make-your-uno-kit_assembled.jpg?v=1698678130,https://www.elektor.com/cdn/shop/files/arduino-make-your-uno-kit_components.jpg?v=1698678130,https://www.elektor.com/cdn/shop/files/arduino-make-your-uno-kit_packaging.jpg?v=1698678130,https://www.elektor.com/cdn/shop/files/arduino-make-your-uno-kit_parts.jpg?v=1698678130https://www.elektor.com/products/arduino-make-your-uno-kit?variant=46907244020044 in stock 79.95 42 0 6.9 2 - 4 Werktage 46907189100876 Arduino Mega 2560 Rev3 Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR Comparison Websites 7640152110085 It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila. Operating Voltage 5 V Input Voltage 7 V - 12 V Digital I/O 54 Analog Input Pins 16 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 256 KB of which 8 KB used by the bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16MHz LED_Builtin 13 Length 101.52 mm Width 53.3 mm Weight 37 g For more information, check out the Getting Started Guide from Arduino. https://www.elektor.com/cdn/shop/files/arduino_mega_2560_rev3_-_overview.jpg?v=1698678135https://www.elektor.com/cdn/shop/files/arduino_mega_2560_rev3_-_bottom.jpg?v=1698678135https://www.elektor.com/products/arduino-mega-2560-rev3?variant=46907189100876 in stock 44.95 24 4.9 6.9 2 - 4 Werktage 46907191034188 Arduino Micro with Headers Arduino Trade Arduino > Arduino Boards > Bestsellers 9783645651929 The Micro contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard. The Micro board is similar to the Arduino Leonardo in that the ATmega32U4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port. Microcontroller ATmega32U4 Operating Voltage 5 V Input Voltage 7 V - 12 V Analog Input Pins 12 PWM Pins 7 DC I/O Pin 20 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB of which 4 KB used by the bootloader SRAM 2.5 KB EEPROM 1 KB Clock Speed 16 MHz LED_Builtin 13 Length 45 mm Width 18 mm Weight 13 g https://www.elektor.com/cdn/shop/files/arduino_micro_with_headers_-_overview.jpg?v=1698678141https://www.elektor.com/cdn/shop/files/arduino_micro_with_headers_-_bottom.jpg?v=1698678141,https://www.elektor.com/cdn/shop/files/arduino_micro_with_headers_-_package.jpg?v=1698678141https://www.elektor.com/products/arduino-micro-with-headers?variant=46907191034188 in stock 24.95 5 4.9 6.9 2 - 4 Werktage 46907049279820 Arduino MKR FOX 1200 Arduino Boards&Kits Arduino > Arduino Boards 813747020572 The Arduino MKR FOX 1200 combines SigFox connectivity with the functionality of the Arduino MKR Zero. It is the ideal solution for beginners wanting to design IoT projects with a low power device. The Arduino MKR FOX 1200 is based on the Atmel SAMD21 and an ATA8520 SigFox module. The intelligent design enables the ability to power the board using an external 5 V power supply or two 1.5 V AA or AAA batteries. Features 32-bit computational power Rich set of I/O interfaces Low power SigFox communication Automatic switch between the two sources These features make this board an excellent choice for IoT battery-powered projects in a compact form factor. The USB port can supply power (5 V) to the board. The Arduino MKR FOX 1200 can run with or without the batteries connected and has limited power consumption. Please note: Unlike most Arduino boards, the Arduino MKR FOX 1200 runs at 3.3 V. The maximum voltage the I/O pins can handle is 3.3 V. Applying voltages higher than 3.3 V to any I/O pin could damage the board. While output to 5 V digital devices is possible, bidirectional communication with 5 V devices needs proper level shifting. Specifications Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Board Power Supply (USB/VIN) 5 V Circuit Operating Voltage 3.3 V PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 - or 19) Digital I/O Pins 8 UART 1 I²C 1 SPI 1 External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 - or 16-, A2 - or 17) Analog Input Pins 7 (ADC 8 / 10 / 12 bit) Analog Output Pins 1 (DAC 10 bit) DC Current per I/O Pin 7 mA SRAM 32 KB Flash Memory 256 KB EEPROM No Clock Speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 6 Full-Speed USB Device and embedded Host LED_BUILTIN 6 Antenna power 2 dB Carrier frequency 868 MHz Working region EU Dimensions 7.64 x 25 mm Weight 32 g Antenna The Arduino MKR FOX 1200 requires a GSM antenna to be attached to the board with the micro UFL connector; please make sure that the antenna is compatible with the frequencies in the SigFox's range (868 Mhz). Please note: Do not attach the antenna to a metallic surface Batteries, Pins and board LEDs Battery capacity: The batteries must have a voltage of 1.5 V. Battery connector: To connect a battery pack (2x AA or AAA) to the Arduino MKR FOX 1200, use the screw terminal block. Polarity: On the silk in the bottom of the board, a positive pin is the closest to the USB connector VIN: This pin can power the board with a regulated 5 V source. If the power goes through this pin, the USB power source is disconnected. That is the only way to supply 5 V to the board, without using USB. 5 V: This pin outputs 5 V from the board when powered from the USB connector or the VIN pin. VCC: This pin outputs 3.3 V through the on-board voltage regulator. This voltage is 3.3 V if USB or VIN is used or equal the two batteries if they are used LED ON: The LED is connected to the 5 V input from either USB or VIN. It is not connected to the batteries. That results in the LED lighting up when the power comes from USB or VIN and staying off when the board is running on battery. That minimizes the waste of energy stored in the battery. Onboard LED: On Arduino MKR FOX 1200, the built-in LED is connected to D6 and not D13 as on the other boards. Blink example or other sketches that uses pin 13 for onboard LED may need to be changed to work properly. https://www.elektor.com/cdn/shop/files/19096_-_overview.jpg?v=1698678147https://www.elektor.com/cdn/shop/files/19096_-_bottom_view.jpg?v=1698678147,https://www.elektor.com/cdn/shop/files/19096_-_mkr1000_pinout.jpg?v=1698678147https://www.elektor.com/products/arduino-mkr-fox-1200?variant=46907049279820 out of stock 49.95 0 4.9 6.9 nicht auf Lager 0.032 kg 46907248410956 Arduino MKR IoT Bundle 1010 Arduino Trade Arduino > Arduino Kits > Bestsellers > IoT & LoRa > Platforms 7630049203914 The best way to start exploring the world of connected devices using the Arduino MKR WiFi 1010. The MKR IoT bundle contains all you need to build your first connected devices. Follow the 5 step by step tutorials we have prepared for you and combining the electronic components included in the bundle, you’ll quickly learn how to build devices that connect to the Arduino IoT cloud. All you need to start with IoT This bundle is contains all the hardware and software required to build your first IoT devices with no extra fees. Build 5 IoT projects All the components needed to start your journey into building your own IoT projects. Learn about the Arduino IoT cloud Not only learn about electronic but also about the possibilities the Arduino IoT cloud can offer. Included 1x Arduino MKR1000 WiFi (with mounted headers) 6x Phototransistors 1x Tilt Sensor 1x Temperature sensor (TMP36) 3x Potentiometer 1x Piezo capsule 10x Pushbuttons 1x DC Motor 1x Small servo motor 1x Alphanumeric LCD (16x2 characters) 1x Optocouplers (4N35) 1x H-bridge motor driver (L293D) 2x Mosfet transistors (IRF520) 5x Capacitors 100uF 70x Solid core jumper wires 1x Micro USB cable 1x Breadboard 1x LED (bright white) 3x LEDs (blue) 1x LED (RGB) 8x LED 5 mm (red) 8x LED 5 mm (green) 8x LED 5 mm (yellow) 1x Male pins strip (4x1) 1x Stranded jumper wires (red) 1x Stranded jumper wires (black) 5x Diode 20x 220 Ω resistors 5x 560 Ω resistors 5x 1 KΩ resistors 5x 4.7 KΩ resistors 20x 10 KΩ resistors 5x 1 MΩ resistors 5x 10 MΩ resistors https://www.elektor.com/cdn/shop/files/arduino-mkr-iot-bundle-1010.jpg?v=1689091934https://www.elektor.com/products/arduino-mkr-iot-bundle-1010?variant=46907248410956 in stock 109.95 5 0 0 2 - 4 Werktage 46907190903116 Arduino MKR IoT Carrier Arduino Trade Arduino > Arduino Shields > Bestsellers > IoT & LoRa > Platforms 7630049202597 Data Capture: Map the environment around the carrier using the integrated temperature, humidity, and pressure sensors and collect data about movement using the 6 axis IMU and light, gesture, and proximity sensors. Easily add more external sensors to capture more data from more sources via the on-board Grove connectors (x3). Data Storage: Capture and store all the data locally on an SD card, or connect to the Arduino IoT Cloud for real-time data capture, storage, and visualization. Data Visualisation: Locally view real-time sensor readings on the built-in OLED Color Display and create visual or sound prompts using the embedded LEDs and buzzer. Total Control: Directly control small-voltage electronic appliances using the onboard relays and the five tactile buttons, with the integrated display providing a handy on-device interface for immediate control. https://www.elektor.com/cdn/shop/files/arduino_mkr_iot_carrier_-_overview.jpg?v=1698678156https://www.elektor.com/cdn/shop/files/arduino_mkr_iot_carrier_-_pcb.jpg?v=1698678156,https://www.elektor.com/cdn/shop/files/arduino_mkr_iot_carrier_-_bottom.jpg?v=1698678156https://www.elektor.com/products/arduino-mkr-iot-drager?variant=46907190903116 in stock 57.95 14 0 6.9 2 - 4 Werktage 46907244937548 Arduino MKR NB 1500 Arduino Trade Arduino > Arduino Boards > Bestsellers > Components > Development Boards 7630049200012 Arduino MKR NB 1500 allows you to build your next smart project. Ever wanted an automated house? Or a smart garden? Well, now it’s easy with the Arduino IoT Cloud compatible boards. It means: you can connect devices, visualize data, control and share your projects from anywhere in the world. Whether you’re a beginner or a pro, we have a wide range of plans to make sure you get the features you need. Add Narrowband communication to your project with the MKR NB 1500. It's the perfect choice for devices in remote locations without an Internet connection, or in situations in which power isn't available like on-field deployments, remote metering systems, solar-powered devices, or other extreme scenarios. The board's main processor is a low power ARM Cortex-M0 32-bit SAMD21, like in the other boards within the Arduino MKR family. The Narrowband connectivity is performed with a module from u-blox, the SARA-R410M-02B, a low power chipset operating in the de different bands of the IoT LTE cellular range. On top of those, secure communication is ensured through the Microchip ECC508 crypto chip. Besides that, the pcb includes a battery charger, and a connector for an external antenna. This board is designed for global use, providing connectivity on LTE's Cat M1/NB1 bands 1, 2, 3, 4, 5, 8, 12, 13, 18, 19, 20, 25, 26, 28. Operators offering service in that part of the spectrum include: Vodafone, AT&T, T-Mobile USA, Telstra, and Verizon, among others. Specifications The Arduino MKR NB 1500 is based on the SAMD21 microcontroller. Microcontroller SAMD21 Cortex-M0+ 32-bit low power ARM MCU (datasheet) Radio module u-blox SARA-R410M-02B (datasheet summary) Secure element ATECC508 (datasheet) Board power supply (USB/VIN) 5 V Supported battery Li-Po Single Cell, 3.7 V, 1500 mAh Minimum Circuit operating voltage 3.3 V Digital I/O pins 8 PWM pins 13 (0 .. 8, 10, 12, 18 / A3, 19 / A4) UART 1 SPI 1 I²C 1 Analog input pins 7 (ADC 8/10/12 bit) Analog output pins 1 (DAC 10 bit) External interrupts 8 (0, 1, 4, 5, 6, 7, 8, 16 / A1, 17 / A2) DC current per I/O pin 7 mA Flash memory 256 KB (internal) SRAM 32 KB EEPROM No Clock speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 6 USB Full-speed USB device and embedded host Antenna gain 2 dB Carrier frequency LTE bands 1, 2, 3, 4, 5, 8, 12, 13, 18, 19, 20, 25, 26, 28 Power class (radio) LTE Cat M1 / NB1: Class 3 (23 dBm) Data rate (LTE M1 halp-duplex) UL 375 kbps / DL 300 kbps Data rate (LTE NB1 full-duplex) UL 62.5 kbps / DL 27.2 kbps Working region Multiregion Device location GNSS via modem Power consumption (LTE M1) min 100 mA / max 190 mA Power consumption (LTE NB1) min 60 mA / max 140 mA SIM card MicroSIM (not included with the board) Dimensions 67.6 x 25 mm Weight 32 g Downloads Eagle Files Schematics Pinout https://www.elektor.com/cdn/shop/files/arduino-mkr-nb-1500.jpg?v=1698678162https://www.elektor.com/cdn/shop/files/arduino-mkr-nb-1500_back.jpg?v=1698678162,https://www.elektor.com/cdn/shop/files/arduino-mkr-nb-1500_packaging.jpg?v=1698678162https://www.elektor.com/products/arduino-mkr-nb-1500?variant=46907244937548 in stock 94.95 24 0 6.9 2 - 4 Werktage 46907244052812 Arduino MKR WAN 1310 Arduino Trade Arduino > Arduino Shields > Bestsellers > IoT & LoRa > Platforms 7630049201484 Ever wanted an automated house? Or a smart garden? Well, now it’s easy with the Arduino IoT Cloud compatible boards. It means: you can connect devices, visualize data, control and share your projects from anywhere in the world. Whether you’re a beginner or a pro, we have a wide range of plans to make sure you get the features you need. Connect your sensors and actuators over long distances harnessing the power of the LoRa wireless protocol or throughout LoRaWAN networks. The Arduino MKR WAN 1310 board provides a practical and cost effective solution to add LoRa connectivity to projects requiring low power. This open source board can be connected to the Arduino IoT Cloud. Better and More Efficient The MKR WAN 1310, brings in a series of improvements when compared to its predecessor, the MKR WAN 1300. While still based on the Microchip SAMD21 low power processor, the Murata CMWX1ZZABZ LoRa module, and the MKR family’s characteristic crypto chip (the ECC508), the MKR WAN 1310 includes a new battery charger, a 2 MByte SPI Flash, and improved control of the board’s power consumption. Improved Battery Power The latest modifications have considerably improved the battery life on the MKR WAN 1310. When properly configured, the power consumption is now as low as 104 uA! It is also possible to use the USB port to supply power (5 V) to the board; run the board with or without batteries – the choice is yours. On-board Storage Data logging and other OTA (Over The Air) functions are now possible since the inclusion of the on board 2 MByte Flash. This new exciting feature will let you transfer configuration files from the infrastructure onto the board, create your own scripting commands, or simply store data locally to send it whenever the connectivity is best. Whilst the MKR WAN 1310’s crypto chip adds further security by storing credentials & certificates in the embedded secure element. These features make it the perfect IoT node and building block for low-power wide-area IoT devices. Specifications The Arduino MKR WAN 1310 is based on the SAMD21 microcontroller. Microcontroller SAMD21 Cortex-M0+ 32-bit low power ARM MCU (datasheet) Radio module CMWX1ZZABZ (datasheet) Board power supply (USB/VIN) 5 V Secure element ATECC508 (datasheet) Supported batteries Rechargeable Li-Ion, or Li-Po, 1024 mAh minimum capacity Circuit operating voltage 3.3 V Digital I/O pins 8 PWM pins 13 (0 .. 8, 10, 12, 18 / A3, 19 / A4) UART 1 SPI 1 I²C 1 Analog input pins 7 (ADC 8/10/12 bit) Analog output pins 1 (DAC 10 bit) External interrupts 8 (0, 1, 4, 5, 6, 7, 8, 16 / A1, 17 / A2) DC current per I/O pin 7 mA CPU flash memory 256 KB (internal) QSPI flash memory 2 MByte (external) SRAM 32 KB EEPROM No Clock speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 6 USB Full-Speed USB Device and embedded Host Antenna gain 2 dB (bundled pentaband antenna) Carrier frequency 433/868/915 MHz Dimensions 67.64 x 25 mm Weight 32 g Downloads Eagle Files Schematics Fritzing Pinout https://www.elektor.com/cdn/shop/files/arduino-mkr-wan-1310.jpg?v=1698678171https://www.elektor.com/cdn/shop/files/arduino-mkr-wan-1310_front.jpg?v=1698678171,https://www.elektor.com/cdn/shop/files/arduino-mkr-wan-1310_back.jpg?v=1698678171,https://www.elektor.com/cdn/shop/files/arduino-mkr-wan-1310_packaging.jpg?v=1698678171https://www.elektor.com/products/arduino-mkr-wan-1310?variant=46907244052812 in stock 59.95 16 0 6.9 2 - 4 Werktage 46907189690700 Arduino MKR WiFi 1010 Arduino Trade Arduino > Arduino Boards > Bestsellers 7630049200258 The board's main processor is a low-power ARM Cortex-M0 32-bit SAMD21, like in the other boards within the Arduino MKR family. The WiFi and Bluetooth connectivity is performed with a module from u-blox, the NINA-W10, a low-power chipset operating in the 2.4 GHz range. On top of that, secure communication is ensured through the Microchip ECC508 crypto chip. Besides that, you can find a battery charger, and an RGB LED on-board. Official Arduino WiFi Library You can get your board to connect to any kind of existing WiFi network, or use it to create your own Arduino Access Point. The specific set of examples we provide for the MKR WiFi 1010 can be consulted at the WiFiNINA library reference page. Compatible with other Cloud Services It is also possible to connect your board to different Cloud services, Arduino's own among others. Here are some examples of how to get the MKR WiFi 1010 to connect to: Blynk: a simple project from the Arduino community connecting to Blynk to operate your board from a phone with little code IFTTT: in-depth case of building a smart plug connected to IFTTT AWS IoT Core: Arduino made this example on how to connect to Amazon Web Services Azure: visit this GitHub repository explaining how to connect a temperature sensor to Azure's Cloud Firebase: you want to connect to Google's Firebase, this Arduino library will show you how Specifications Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Radio Module u-blox NINA-W102 Power Supply 5 V Secure Element ATECC508 Supported Battery Li-Po Single Cell, 3.7 V, 1024 mAh Minimum Operating Voltage 3.3 V Digital I/O Pins 8 PWM Pins 13 UART 1 SPI 1 I2C 1 Analog Input Pins 7 Analog Output Pins 1 External Interrupts 10 Flash Memory 256 KB SRAM 32 KB EEPROM no Clock Speed 32.768 kHz, 48 MHz LED_Builtin 6 USB Full-Speed USB Device and embedded Host Length 61.5 mm Width 25 mm Weight 32 g https://www.elektor.com/cdn/shop/files/arduino_mkr_wifi_1010_-_overview.jpg?v=1698678177https://www.elektor.com/cdn/shop/files/arduino_mkr_wifi_1010_-_bottom.jpg?v=1698678177,https://www.elektor.com/cdn/shop/files/arduino_mkr_wifi_1010_-_package.jpg?v=1698678177https://www.elektor.com/products/arduino-mkr-wifi-1010?variant=46907189690700 in stock 39.95 19 4.9 6.9 2 - 4 Werktage 46907245232460 Arduino MKR Zero Arduino Trade Arduino > Arduino Boards > Bestsellers > Components > Development Boards 7630049200470 The Arduino MKR Zero is a development board for music makers! With an SD card holder and dedicated SPI interfaces (SPI1), you are able to play music files without extra hardware. The MKR Zero brings you the power of a Zero in the smaller format established by the MKR form factor. The MKR Zero board acts as a great educational tool for learning about 32-bit application development. It has an on-board SD connector with dedicated SPI interfaces (SPI1) that allows you to play with MUSIC files with no extra hardware! The board is powered by Atmel’s SAMD21 MCU, which features a 32-bit ARM Cortex M0+ core. The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-USB cable or power it by a LiPo battery. The battery voltage can also be monitored since a connection between the battery and the analog converter of the board exists. Specifications Microcontroller SAMD21 ARM Cortex-M0+ 32-bit low power Board power supply (USB/VIN) 5 V Supported battery Li-Po single cell, 3.7 V, 700 mAh minimum DC current for 3.3 V pin 600 mA DC current for 5 V pin 600 mA Circuit operating voltage 3.3 V Digital I/O pins 22 PWM pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19) UART 1 SPI 1 I²C 1 Analog input pins 7 (ADC 8/10/12 bit) Analog output pins 1 (DAC 10 bit) External interrupts 10 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17) DC current per I/O pin 7 mA Flash memory 256 KB Flash memory for bootloader 8 KB SRAM 32 KB EEPROM No Clock speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 32 Downloads Datasheet Eagle Files Schematics Fritzing Pinout https://www.elektor.com/cdn/shop/files/arduino-mkr-zero.jpg?v=1698678186https://www.elektor.com/cdn/shop/files/arduino-mkr-zero_front.jpg?v=1698678186,https://www.elektor.com/cdn/shop/files/arduino-mkr-zero_back.jpg?v=1698678186,https://www.elektor.com/cdn/shop/files/arduino-mkr-zero_packaging.jpg?v=1698678186https://www.elektor.com/products/arduino-mkr-zero?variant=46907245232460 in stock 36.95 20 4.9 6.9 2 - 4 Werktage 46906946191692 Arduino Nano Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR Comparison Websites 8058333490342 The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x). It has more or less the same functionality of the Arduino Duemilanove but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one. The Nano was designed and is being produced by Gravitech. Specifications Microcontroller ATmega328 Operating Voltage (logic level) 5 V Input Voltage (recommended) 7-12 V Input Voltage (limits) 6-20 V Digital I/O Pins 14 (of which 6 provide PWM output) Analog Input Pins 8 DC Current per I/O Pin 40 mA Flash Memory 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader SRAM 1 KB (ATmega168) or 2 KB (ATmega328) EEPROM 512 bytes (ATmega168) or 1 KB (ATmega328) Clock Speed 16 MHz Dimensions 0.73 x 1.70' (18 x 45 mm) Power The Arduino Nano can be powered via the Mini-B USB connection, 6-20 V unregulated external power supply (pin 30), or 5 V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source. Memory The ATmega168 has 16 KB of flash memory for storing code (of which 2 KB is used for the bootloader), 1 KB of SRAM and 512 bytes of EEPROM The ATmega328 has 32 KB of flash memory for storing code, (also with 2 KB used for the bootloader), 2 KB of SRAM and 1 KB of EEPROM. Input and Output Each of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 V. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. Communication The Arduino Nano has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega168 and ATmega328 provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1). A SoftwareSerial library allows for serial communication on any of the Nano's digital pins. Programming The Arduino Nano can be programmed with the Arduino software (download). The ATmega168 or ATmega328 on the Arduino Nano comes with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files). You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see these instructions for details. Automatic (Software) Reset Rather than requiring a physical press of the reset button before an upload, the Arduino Nano is designed in a way that allows it to be reset by software running on a connected computer. One of the hardware flow control lines (DTR) of theFT232RL is connected to the reset line of the ATmega168 or ATmega328 via a 100 nF capacitor. When this line is asserted (taken low), the reset line drops long enough to reset the chip. The Arduino software uses this capability to allow you to upload code by simply pressing the upload button in the Arduino environment. This means that the bootloader can have a shorter timeout, as the lowering of DTR can be well-coordinated with the start of the upload. https://www.elektor.com/cdn/shop/files/arduino-nano.jpg?v=1698678192https://www.elektor.com/cdn/shop/files/arduino-nano_front.jpg?v=1698678192,https://www.elektor.com/cdn/shop/files/arduino-nano_back.jpg?v=1698678192https://www.elektor.com/products/arduino-nano?variant=46906946191692 in stock 22.95 61 4.9 6.9 2 - 4 Werktage 46907252834636 Arduino Nano 33 BLE Sense Rev2 with Headers Arduino Trade Arduino > Arduino Boards > Bestsellers 7630049203495 The Arduino Nano 33 BLE Sense Rev2 with headers is Arduino’s 3.3 V AI enabled board in the smallest available form factor with a set of sensors that will allow you without any external hardware to start programming your next project, right away. With the Arduino Nano 33 BLE Sense Rev2, you can: Build wearable devices that using AI can recognize movements. Build a room temperature monitoring device that can suggest or modify changes in the thermostat. Build a gesture or voice recognition device using the microphone or the gesture sensor together with the AI capabilities of the board. Differences between Rev1 and Rev2 Replacement of IMU from LSM9DS1 (9 axis) for a combination of two IMUs (BMI270 – 6 axis IMU and BMM150 – 3 axis IMU) Replacement of temperature and humidity sensor from HTS221 for HS3003 Replacement of microphone from MP34DT05 to MP34DT06JTR Replacement of power supply MPM3610 for MP2322 Addition of VUSB soldering jumper on the top side of the board New test point for USB, SWDIO and SWCLK Specifications Microcontroller nRF52840 (datasheet) Operating Voltage 3.3 V Input Voltage (limit) 21 V DC Current per I/O Pin 15 mA Clock Speed 64 MHz CPU Flash Memory 1 MB (nRF52840) SRAM 256 KB (nRF52840) EEPROM None Digital Input / Output Pins 14 PWM Pins All digital pins UART 1 SPI 1 I²C 1 Analog Input Pins 8 (ADC 12 bit 200 k samples) Analog Output Pins Only through PWM (no DAC) External Interrupts All digital pins LED_BUILTIN 13 USB Native in the nRF52840 Processor IMU BMI270 (datasheet) and BMM150 (datasheet) Microphone MP34DT06JTR (datasheet) Gesture, light, proximity, color APDS9960 (datasheet) Barometric pressure LPS22HB (datasheet) Temperature, humidity HS3003 (datasheet) Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-nano-33-ble-sense-rev2-with-headers.jpg?v=1698678201https://www.elektor.com/cdn/shop/files/arduino-nano-33-ble-sense-rev2-with-headers_front.jpg?v=1698678201,https://www.elektor.com/cdn/shop/files/arduino-nano-33-ble-sense-rev2-with-headers_back.jpg?v=1698678201,https://www.elektor.com/cdn/shop/files/arduino-nano-33-ble-sense-rev2-with-headers_package.jpg?v=1698678201https://www.elektor.com/products/arduino-nano-33-ble-sense-rev2-with-headers?variant=46907252834636 in stock 54.95 17 0 6.9 2 - 4 Werktage 46907189952844 Arduino Nano 33 IoT with Headers Arduino Trade Arduino > Arduino Boards > Bestsellers 7630049201545 The board's main processor is a low-power Arm® Cortex®-M0 32-bit SAMD21. The WiFi and Bluetooth® connectivity is performed with a module from u-blox, the NINA-W10, a low-power chipset operating in the 2.4GHz range. On top of that, secure communication is ensured through the Microchip® ECC608 crypto chip. Besides that, you can find a 6 axis IMU, which makes this board perfect for simple vibration alarm systems, pedometers, the relative positioning of robots, etc. WiFi and Arduino IoT Cloud You can get your board to connect to any kind of existing WiFi network, or use it to create your own Arduino Access Point. The specific set of examples we provide for the Nano 33 IoT can be consulted at the WiFiNINA library reference page. It is also possible to connect your board to different Cloud services, Arduino's own among others. Here are some examples of how to get the Arduino boards to connect to: Arduino's own IoT Cloud: Arduino's IoT Cloud is a simple and fast way to ensure secure communication for all of your connected Things. Check it out here. Blynk: a simple project from our community connecting to Blynk to operate your board from a phone with little code. IFTTT: see an in-depth case of building a smart plug connected to IFTTT. AWS IoT Core: we made this example on how to connect to Amazon Web Services. Azure: visit this GitHub repository explaining how to connect a temperature sensor to Azure's Cloud. Firebase: you want to connect to Google's Firebase, this Arduino library will show you how. Microcontroller SAMD21 Cortex®-M0+ 32bit low power ARM MCU Radio Module u-blox NINA-W102 Secure Element ATECC608A Operating Voltage 3.3 V Input Voltage 21 V Digital I/O Pins 14 PWM Pins 11 DC Current per I/O Pin 7 mA Analog Input Pins 8 Analog Output Pins 1 External Interrupts all digital pins UART 1 SPI 1 I2C 1 Flash Memory 256 KB SRAM 32 KB EEPROM none Clock Speed 48 MHz LED_Builtin 13 USB Native in the SAMD21 Processor IMU LSM6DS3 Length 45 mm Width 18 mm Weight 5 g https://www.elektor.com/cdn/shop/files/arduino_nano_33_iot_with_headers_-_overview.jpg?v=1698678207https://www.elektor.com/cdn/shop/files/arduino_nano_33_iot_with_headers_-_package.jpg?v=1698678207https://www.elektor.com/products/arduino-nano-33-iot-with-headers?variant=46907189952844 in stock 32.95 8 4.9 6.9 2 - 4 Werktage 47310490468684 Arduino Nano ESP32 Arduino Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > ESP Comparison Websites 7630049204584 The Arduino Nano ESP32 (with and without headers) is a Nano form factor board based on the ESP32-S3 (embedded in the NORA-W106-10B from u-blox). This is the first Arduino board to be based fully on an ESP32, and features Wi-Fi, Bluetooth LE, debugging via native USB in the Arduino IDE as well as low power. The Nano ESP32 is compatible with the Arduino IoT Cloud, and has support for MicroPython. It is an ideal board for getting started with IoT development. Features Tiny footprint: Designed with the well-known Nano form factor in mind, this board's compact size makes it perfect for embedding in standalone projects. Wi-Fi and Bluetooth: Harness the power of the ESP32-S3 microcontroller, well-known in the IoT realm, with full Arduino support for wireless and Bluetooth connectivity. Arduino and MicroPython support: Seamlessly switch between Arduino and MicroPython programming with a few simple steps. Arduino IoT Cloud compatible: Quickly and easily create IoT projects with just a few lines of code. The setup takes care of security, allowing you to monitor and control your project from anywhere using the Arduino IoT Cloud app. HID support: Simulate human interface devices, such as keyboards or mice, over USB, opening up new possibilities for interacting with your computer. Specifications Microcontroller u-blox NORA-W106 (ESP32-S3) USB connector USB-C Pins Built-in LED pins 13 Built-in RGB LED pins 14-16 Digital I/O pins 14 Analog input pins 8 PWM pins 5 External interrupts All digital pins Connectivity Wi-Fi u-blox NORA-W106 (ESP32-S3) Bluetooth u-blox NORA-W106 (ESP32-S3) Communication UART 2x I²C 1x, A4 (SDA), A5 (SCL) SPI D11 (COPI), D12 (CIPO), D13 (SCK). Use any GPIO for Chip Select (CS) Power I/O Voltage 3.3 V Input voltage (nominal) 6-21 V Source Current per I/O pin 40 mA Sink Current per I/O pin 28 mA Clock speed Processor Up to 240 MHz Memory ROM 384 kB SRAM 512 kB External Flash 128 Mbit (16 MB) Dimensions 18 x 45 mm Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-without-headers.jpg?v=1699287024https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-without-headers_front.jpg?v=1699287024,https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-without-headers_back.jpg?v=1699287024,https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-without-headers_package.jpg?v=1699287025https://www.elektor.com/products/arduino-nano-esp32?variant=47310490468684 in stock 23.95 100 4.9 6.9 2 - 4 Werktage 47318774251852 Arduino Nano ESP32 with Headers Arduino Trade Bestsellers > ESP > NEW 7630049203969 The Arduino Nano ESP32 (with and without headers) is a Nano form factor board based on the ESP32-S3 (embedded in the NORA-W106-10B from u-blox). This is the first Arduino board to be based fully on an ESP32, and features Wi-Fi, Bluetooth LE, debugging via native USB in the Arduino IDE as well as low power. The Nano ESP32 is compatible with the Arduino IoT Cloud, and has support for MicroPython. It is an ideal board for getting started with IoT development. Features Tiny footprint: Designed with the well-known Nano form factor in mind, this board's compact size makes it perfect for embedding in standalone projects. Wi-Fi and Bluetooth: Harness the power of the ESP32-S3 microcontroller, well-known in the IoT realm, with full Arduino support for wireless and Bluetooth connectivity. Arduino and MicroPython support: Seamlessly switch between Arduino and MicroPython programming with a few simple steps. Arduino IoT Cloud compatible: Quickly and easily create IoT projects with just a few lines of code. The setup takes care of security, allowing you to monitor and control your project from anywhere using the Arduino IoT Cloud app. HID support: Simulate human interface devices, such as keyboards or mice, over USB, opening up new possibilities for interacting with your computer. Specifications Microcontroller u-blox NORA-W106 (ESP32-S3) USB connector USB-C Pins Built-in LED pins 13 Built-in RGB LED pins 14-16 Digital I/O pins 14 Analog input pins 8 PWM pins 5 External interrupts All digital pins Connectivity Wi-Fi u-blox NORA-W106 (ESP32-S3) Bluetooth u-blox NORA-W106 (ESP32-S3) Communication UART 2x I²C 1x, A4 (SDA), A5 (SCL) SPI D11 (COPI), D12 (CIPO), D13 (SCK). Use any GPIO for Chip Select (CS) Power I/O Voltage 3.3 V Input voltage (nominal) 6-21 V Source Current per I/O pin 40 mA Sink Current per I/O pin 28 mA Clock speed Processor Up to 240 MHz Memory ROM 384 kB SRAM 512 kB External Flash 128 Mbit (16 MB) Dimensions 18 x 45 mm Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-with-headers.jpg?v=1699464768https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-with-headers_front.jpg?v=1699544615,https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-with-headers_back.jpg?v=1699544615,https://www.elektor.com/cdn/shop/files/arduino-nano-esp32-with-headers_package.jpg?v=1699544615https://www.elektor.com/products/arduino-nano-esp32-with-headers?variant=47318774251852 in stock 24.95 44 4.9 6.9 2 - 4 Werktage 46907190247756 Arduino Nano Every with Headers Arduino Trade Arduino > Arduino Boards 7630049201552 The Arduino Nano Every is an evolution of the traditional Arduino Nano board but features a lot more powerful processor, the ATMega4809. This will allow you to make larger programs than with the Arduino Uno (it has 50% more program memory), and with a lot more variables (the RAM is 200% bigger). An Improved Arduino Nano If you used Arduino Nano in your projects in the past, the Nano Every is a pin-equivalent substitute. The main differences are a better processor and a micro-USB connector. The board comes in two options: with or without headers, allowing you to embed the Nano Every inside any kind of invention, including wearables. The board comes with tessellated connectors and no components on the B-side. These features allow you to solder the board directly onto your own design, minimizing the height of your whole prototype. Oh, and did we mention the improved price? Thanks to a revised manufacturing process, the Arduino Nano Every costs a fraction of the original Nano … what are you waiting for? Upgrade now! Microcontroller ATMega4809 Operating Voltage 5 V Input Voltage 7 V - 21 V Analog Input Pins 8 Analog Output Pins Only through PWM External Interrupts all digital pins DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 48 KB SRAM 6 KB EEPROM 256 Byte Clock Speed 20 MHz LED_Builtin 13 UART 1 SPI 1 I2C 1 PWM Pins 5 USB Uses the ATSAMD11D14A Length 45 mm Width 18 mm Weight 5 g https://www.elektor.com/cdn/shop/files/arduino_nano_every_with_headers_-_overview.jpg?v=1698678213https://www.elektor.com/cdn/shop/files/arduino_nano_every_with_headers_-_package.jpg?v=1698678213https://www.elektor.com/products/arduino-nano-every-with-headers?variant=46907190247756 out of stock 19.95 0 4.9 6.9 nicht auf Lager 46907152400716 Arduino Nano RP2040 Connect with Headers Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR > NEW > Pico RP2040 > Raspberry Pi Comparison Websites 7630049203068 The Arduino Nano RP2040 Connect is an RP2040-based Arduino board equipped with Wi-Fi (802.11b/g/n) and Bluetooth 4.2. Besides wireless connectivity the board comes with a microphone for sound and voice activation and a six-axis smart motion sensor with AI capabilities. An RGB LED is available too. 22 GPIO ports (20 with PWM support and eight analogue inputs) let the user control e.g. relays, motors and LEDs and read switches and other sensors. Program memory is plentiful with 16 MB of flash memory, more than enough room for storing many webpages or other data. Technical Specifications Microcontroller Raspberry Pi RP2040 USB connector Micro USB Pins Built-in LED pins 13 Digital I/O pins 20 Analog Input pins 8 PWM pins 20 (Except A6, A7) External interrupts 20 (Except A6, A7) Connectivity Wi-Fi Nina W102 uBlox module Bluetooth Nina W102 uBlox module Secure element ATECC608A-MAHDA-T Crypto IC Sensors IMU LSM6DSOXTR (6-axis) Microphone MP34DT05 Communication UART Yes I²C Yes SPI Yes Power Circuit operating voltage 3.3 V Input Voltage (VIN) 5-21 V DC Current per I/O pin 4 mA Clock speed Processor 133 MHz Memory AT25SF128A-MHB-T 16 MB Flash IC Nina W102 uBlox module 448 KB ROM, 520 KB SRAM, 16 MB Flash Dimensions 45 x 18 mm Weight 6 g Downloads Schematics Pinout Datasheet https://www.elektor.com/cdn/shop/files/arduino-nano-rp2040-connect-with-headers.jpg?v=1698678222https://www.elektor.com/cdn/shop/files/arduino-nano-rp2040-connect-with-headers_front.jpg?v=1698678222,https://www.elektor.com/cdn/shop/files/arduino-nano-rp2040-connect-with-headers_back.jpg?v=1698678222,https://www.elektor.com/cdn/shop/files/arduino-nano-rp2040-connect-with-headers_package.jpg?v=1698678222https://www.elektor.com/products/arduino-nano-rp2040-connect-with-headers?variant=46907152400716 in stock 29.95 20 4.9 6.9 2 - 4 Werktage 46907190608204 Arduino OPLA IoT Starter Kit Arduino Trade Arduino > Arduino Kits > Bestsellers > NEW 7630049202665 The Oplà IoT Kit allows you to add connectivity to devices around the home or workplace. It comes complete with a set of 8 Internet of Things self-assemble projects ready to show you how to turn everyday appliances into ‘smart appliances’ and build custom connected devices that can be controlled with your mobile phone. Remote Controlled Lights - change color, light modes and switch on/off via your mobile Personal Weather Station - record and monitor local weather conditions Home Security Alarm - Detect motions and trigger warnings Solar System Tracker - retrieve data from planets and moons in the Solar System Inventory Control - track goods in & out Smart Garden - monitor and control the environment for your plants Thermostat Control - smart control for heating and cooling systems Thinking About You - send messages between the Oplà and the Arduino IoT Cloud For more advanced users the kit provides them with the potential to create their own connected devices and IoT applications through the open programmable platform providing the ultimate control. The Oplà unit acts as the physical interface with the Arduino IoT Cloud providing you with total control at your fingertips via the Arduino IoT Remote app. Configure and manage all the settings via the Arduino IoT Cloud, with easy to create dashboards providing real-time readings from your smart devices around the home or workplace. Adjusting settings, switching devices on/off, watering plants, etc are all controllable on the go with the Arduino IoT Remote app or fully automate the set-up then sit back and enjoy! Included MKR IoT Carrier designed for this kit, including: Round OLED Display Five capacitive touch buttons On-board sensors (temperature, humidity, pressure, and light) Two 24 V relays SD card holder Plug and play connectors for different sensors RGBC, Gesture, and Proximity IMU 18650 Li-Ion rechargeable battery holder (battery not included) Five RGB LEDs Arduino MKR WiFi 1010 Plastic encasing Micro USB cable Moisture sensor PIR sensor Plug-and-play cables for all the sensors Applications Remote Controlled Lights Personal Weather Station Home Security Alarm Solar System Tracker Inventory Control Smart Garden Thermostat Control Thinking About You https://www.elektor.com/cdn/shop/files/arduino_opla_iot_starter_kit_-_overview.jpg?v=1698678234https://www.elektor.com/cdn/shop/files/arduino_opla_iot_starter_kit_-_pcb.jpg?v=1698678234,https://www.elektor.com/cdn/shop/files/arduino_opla_iot_starter_kit_-_content.jpg?v=1698678234,https://www.elektor.com/cdn/shop/files/arduino_opla_iot_starter_kit_-_package.jpg?v=1698678234https://www.elektor.com/products/arduino-opla-iot-starter-kit?variant=46907190608204 in stock 124.95 13 0 0 2 - 4 Werktage 47310491517260 Arduino Portenta HAT Carrier Arduino Trade Bestsellers 7630049204041 Portenta HAT Carrier is a reliable and robust carrier that transforms Portenta X8 into an industrial single board computer compatible with Raspberry Pi HATs and cameras. It is ideal for multiple industrial applications such as building automation and machine monitoring.Compatible also with Portenta H7 and Portenta C33, Portenta HAT Carrier provides easy access to multiple peripherals – including CAN, Ethernet, microSD and USB – and further extends any Portenta application.It is great for prototyping and ready for scaling up, it extends the features found on a typical Raspberry Pi Model B. Debug quickly with dedicated JTAG pins and keeps heat manageable under intense workloads with a PWM fan connector. Control actuators or read analog sensors via the additional 16x analog I/Os. Add industrial machine vision solutions to any project by leveraging the onboard camera connector.FeaturesAdd Raspberry Pi HATs to your Portenta projectsQuickly access CAN, USB, and Ethernet peripheralsLeverage onboard MicroSD card to log dataEnjoy simple debugging through the onboard JTAG pinsEasily control actuators and read sensors via 16x analog I/OsLeveraging the onboard camera connector for machine visionPortenta takes you from prototype to high-performancePortenta HAT Carrier offers you a frictionless Linux prototyping experience and unlocks the ability for integrated real-time MCU solutions. Portenta HAT Carrier extends Portenta SOMs for faster, easier and more efficient testing for your ideas while also ensuring the capabilities and industrial-grade performances the Portenta range is known for.Extend the Raspberry Pi ecosystem for commercial applicationsCombine the ease of use, accessibility and incredible support from both the Arduino and Raspberry Pi communities for your next project with the carrier designed to combine and extend MPU and MCU applications for the development of advanced commercial solutions.SpecificationsConnectorsHigh-density connectors compatible with Portenta products1x USB-A female connector1x Gigabit Ethernet connector (RJ45)1x CAN FD with onboard transceiver1x MIPI Camera connector1x MicroSD card slot1x PWM fan connector 40-pin header connector allowing compatibility with Raspberry Pi HATs16-pin analog header connectors, including:8x analog inputs1x GPIO1xUART without flow control2x PWM pins1x LICELL pin for Portenta's RTC powerInterfacesCAN FDUARTSAIANALOGGPIOSPII²CI²SPWMDebuggingOnboard 10x pin 1.27 mm JTAG connectorPowerFrom onboard screw terminal block allowing: 7-32 V power supply, powering both the carrier and the connected Portenta5 V power supplyFrom USB-C on PortentaFrom 5 V on 40-pin header connectorDimensions85 x 56 mmDownloadsDatasheetSchematics https://www.elektor.com/cdn/shop/files/arduino-portenta-hat-carrier.jpg?v=1699287291https://www.elektor.com/cdn/shop/files/arduino-portenta-hat-carrier_front.jpg?v=1699287291,https://www.elektor.com/cdn/shop/files/arduino-portenta-hat-carrier_back.jpg?v=1699287291https://www.elektor.com/products/arduino-portenta-hat-carrier?variant=47310491517260 in stock 54.95 7 0 6.9 2 - 4 Werktage 46907243594060 Arduino Pro Nicla Sense ME Arduino Trade Arduino > Arduino Accessories > Bestsellers > IoT & LoRa > Platforms 7630049202849 The Nicla Sense ME is a tiny, low-power tool that sets a new standard for intelligent sensing solutions. With the simplicity of integration and scalability of the Arduino ecosystem, the board combines four state-of-the-art sensors from Bosch Sensortec: BHI260AP motion sensor system with integrated AI BMM150 magnetometer BMP390 pressure sensor BME688 4-in-1 gas sensor with AI and integrated high-linearity, as well as high-accuracy pressure, humidity and temperature sensors. The Arduino Nicla Sense ME is the smallest Arduino form factor yet, with a range of industrial grade sensors packed into a tiny footprint. Measure process parameters such as temperature, humidity and movement. Featuring a 9-axis inertial measurement unit and the possibility for Bluetooth Low Energy connectivity, it can help you to create your next Bluetooth Low Energy enabled project. Make your own industrial grade wireless sensing network with the onboard BHI260AP, BMP390, BMM150 and BME688 Bosch sensors. Features Tiny size, packed with features Low power consumption Add sensing capabilities to existing projects When battery-powered, becomes a complete standalone board Powerful processor, capable of hosting intelligence on the Edge Measures motion and environmental parameters Robust hardware including industrial-grade sensors with embedded AI BLE connectivity maximizes compatibility with professional and consumer equipment 24/7 always-on sensor data processing at ultra-low power consumption Specifications Microcontroller 64 MHz ARM Cortex-M4 (nRF52832) Sensors BHI260AP – Self-learning AI smart sensor with integrated accelerometer and gyroscope BMP390 – Digital pressure sensor BMM150 – Geomagnetic sensor BME688 – Digital low power gas, pressure, temperature & humidity sensor with AI I/O Castellated pins with the following features: 1x I²C bus (with ext. ESLOV connector) 1x serial port 1x SPI 2x ADC, programmable I/O voltage from 1.8-3.3 V Connectivity Bluetooth 4.2 Power Micro USB (USB-B), Pin Header, 3.7 V Li-po battery with Integrated battery charger Memory 512 KB Flash / 64 KB RAM 2 MB SPI Flash for storage 2 MB QSPI dedicated for BHI260AP Interface USB interface with debug functionality Dimensions 22.86 x 22.86 mm Weight 2 g Downloads Datasheet https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-sense-me.jpg?v=1698678243https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-sense-me_back.jpg?v=1698678243,https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-sense-me_view.jpg?v=1698678243,https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-sense-me_packaging.jpg?v=1698678243https://www.elektor.com/products/arduino-pro-nicla-sense-me?variant=46907243594060 in stock 84.95 17 0 6.9 2 - 4 Werktage 46907221803340 Arduino Pro Nicla Vision Arduino Trade Arduino > Arduino Accessories > Bestsellers > IoT & LoRa > Platforms 7630049203037 Ever wanted an automated house? Or a smart garden? The Arduino IoT Cloud compatible board Nicla Vision allows you to build your next smart project. You can connect devices, visualize data, control and share your projects from anywhere in the world. Nicla Vision combines a powerful STM32H747AII6 Dual ARM Cortex M7/M4 IC processor with a 2 MP color camera that supports TinyML, as well as a smart 6-axis motion sensor, integrated microphone and distance sensor. You can easily include it into any project because it’s designed to be compatible with all Arduino Portenta and MKR products, fully integrates with OpenMV, supports MicroPython and also offers both WiFi and Bluetooth Low Energy connectivity. It’s so compact – with its 22.86 x 22.86 mm form factor – it can physically fit into most scenarios, and requires so little energy it can be powered by battery for standalone applications. All of this makes Nicla Vision the ideal solution to develop or prototype with on-device image processing and machine vision at the edge, for asset tracking, object recognition, predictive maintenance and more – easier and faster than ever. Train it to spot details, so you can focus on the big picture. Automate anything Check every product is labeled before it leaves the production line; unlock doors only for authorized personnel, and only if they are wearing PPE correctly; use AI to train Nicla Vision to regularly check analog meters and beam readings to the Cloud; teach it to recognize thirsty crops and turn the irrigation on when needed.Anytime you need to act or make a decision depending on what you see, let Nicla Vision watch, decide and act for you. Feel seen Interact with kiosks with simple gestures, create immersive experiences, work with cobots at your side. Nicla Vision allows computers and smart devices to see you, recognize you, understand your movements and make your life easier, safer, more efficient, better. Keep an eye out Let Nicla Vision be your eyes: detecting animals on the other side of the farm, letting you answer your doorbell from the beach, constantly checking on the vibrations or wear of your industrial machinery. It’s your always-on, always precise lookout, anywhere you need it to be. Downloads Schematics Datasheet https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-vision.jpg?v=1698678248https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-vision_view.jpg?v=1698678248,https://www.elektor.com/cdn/shop/files/arduino-pro-nicla-vision_package.jpg?v=1698678248https://www.elektor.com/products/arduino-pro-nicla-vision?variant=46907221803340 in stock 149.95 6 0 0 2 - 4 Werktage 46907244904780 Arduino Pro Portenta Breakout Arduino Trade Arduino > Arduino Accessories > Arduino Shields > Bestsellers 7630049203013 Portenta Breakout board is designed to help hardware engineers and makers to prototype and help test devices connections and capacity within the Portenta family boards (e.g. the Portenta H7). It makes all high-density connectors’ signals individually accessible, making it quick and easy to connect and test external hardware components and devices as normally needed during development in the lab. Features PowerON Button Boot mode DIP switch Connectors USB-A RJ45 up to 1Gb/s Micro-SD Card MIPI-20T-JTAG with Trace-Capability. Power CR2032 RTC-Lithium battery backup External power terminal block I/O Break out all Portenta High Density connector signals Male/female HD connectors allow interposing breakout between Portenta and shield to debug signals Compatibility Standard Portenta High Density connector pinout Specifications USB Port USB-A Ethernet RJ45 up to 1 Gb/s Memory slot Micro SD card Debug MIPI-20T-JTAG with trace capability Connectors HD Male/Female RTC power battery CR2032 Dimensions 164 x 72 mm Weight 69 g Downloads Datasheet Schematics Pinout https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-breakout.jpg?v=1698678258https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-breakout_front.jpg?v=1698678258,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-breakout_back.jpg?v=1698678258,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-breakout_packaging.jpg?v=1698678258https://www.elektor.com/products/arduino-pro-portenta-breakout?variant=46907244904780 in stock 59.95 3 0 6.9 2 - 4 Werktage 47318771630412 Arduino Pro Portenta C33 Arduino Trade Bestsellers 7630049203556 The Portenta C33 is a powerful System-on-Module designed for low-cost Internet of Things (IoT) applications. Based on the R7FA6M5BH2CBG microcontroller from Renesas, this board shares the same form factor as the Portenta H7 and it is backward compatible with it, making it fully compatible with all Portenta family shields and carriers through its high-density connectors. As a low-cost device, the Portenta C33 is an excellent choice for developers looking to create IoT devices and applications on a budget. Whether you're building a smart home device or a connected industrial sensor, the Portenta C33 provides the processing power and connectivity options you need to get the job done. Quickly deploying AI-powered projects becomes quick and easy with Portenta C33, by leveraging a vast array of ready-to-use software libraries and Arduino sketches available, as well as widgets that display data in real time on Arduino IoT Cloud-based dashboards. Features Ideal for low-cost IoT applications with Wi-Fi/Bluetooth LE connectivity Supports MicroPython and other high-level programming languages Offers industrial-grade security at the hardware level and secure OTA firmware updates Leverages ready-to-use software libraries and Arduino sketches Perfect to monitor and display real-time data on Arduino IoT Cloud widget-based dashboards Compatible with Arduino Portenta and MKR families Features castellated pins for automatic assembly lines Cost Effective Performance Reliable, secure and with computational power worthy of its range, Portenta C33 was designed to provide big and small companies in every field with the opportunity to access IoT and benefit from higher efficiency levels and automation. Applications Portenta C33 brings more applications than ever within users’ reach, from enabling quick plug-and-play prototyping to providing a cost-effective solution for industrial-scale projects. Industrial IoT gateway Machine monitoring to track OEE/OPE Inline quality control and assurance Energy consumption monitoring Appliances control system Ready-to-use IoT prototyping solution Specifications Microcontroller Renesas R7FA6M5BH2CBG ARM Cortex-M33: ARM Cortex-M33 core up to 200 MHz 512 kB onboard SRAM 2 MB onboard Flash Arm TrustZone Secure Crypto Engine 9 External Memories 16 MB QSPI Flash USB-C USB-C High Speed Connectivity 100 MB Ethernet interface (PHY) Wi-Fi Bluetooth Low Energy Interfaces CAN SD Card ADC GPIO SPI I²S I²C JTAG/SWD Security NXP SE050C2 Secure Element Operating Temperatures -40 to +85 °C (-40 to 185 °F) Dimensions 66,04 x 25,40 mm Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-c33.jpg?v=1699464712https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-c33_front.jpg?v=1699544570,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-c33_back.jpg?v=1699544570https://www.elektor.com/products/arduino-pro-portenta-c33?variant=47318771630412 in stock 79.95 34 0 6.9 2 - 4 Werktage 46907245297996 Arduino Pro Portenta Cat-M1 NB-IoT GNSS Shield Arduino Trade Arduino > Arduino Boards > Bestsellers > Components > Development Boards 7630049202962 The Portenta Cat. M1/NB IoT GNSS Shield allows you to enhance the connectivity features of your Portenta H7 applications. The shield leverages a Cinterion TX62 wireless module by Thales, designed for highly efficient, low-power IoT applications to deliver optimized bandwidth and performance. The Portenta Cat. M1/NB IoT GNSS Shield combines with the strong edge computing power of the Portenta H7 to enable the development of asset tracking and remote monitoring applications in industrial settings, as well as in agriculture, public utilities and smart cities. The shield offers cellular connectivity to both Cat. M1 and NB-IoT networks with the option to use eSIM technology. Easily track your valuables – across the city or worldwide – with your choice of GPS, GLONASS, Galileo or BeiDou. Features Change connectivity capabilities without changing the board Add NB-IoT, CAT. M1 and positioning to any Portenta product Possibility to create a small multiprotocol router (WiFi - BT + NB-IoT/CAT. M1) Greatly reduce communication bandwidth requirements in IoT applications Low-power module Compatible also with MKR boards Remote Monitoring Industrial and agricultural companies can leverage the Portenta Cat. M1/NB IoT GNSS Shield to remotely monitor gas detectors, optical sensors, machinery alarm systems, biological bug traps and more. Technology providers providing smart city solutions can compound the power and reliability of the Portenta H7 with the Portenta Cat. M1/NB IoT GNSS Shield, to connect data and automate actions for a truly optimized use of resources and enhanced user experience. Asset Monitoring Add monitoring capabilities to any asset by combining the performance and edge computing features of the Portenta family boards. The Portenta Cat. M1/NB IoT GNSS Shield is ideal to monitor valuable goods and also for monitoring industrial machinery and equipment. Specifications Connectivity Cinterion TX62 wireless module; NB-IoT - LTE CAT.M1; 3GPP Rel.14 Compliant Protocol LTE Cat. M1/NB1/NB2; UMTS BANDS: 1 / 2 / 3 / 4 / 5 / 8 / 12(17) / 13 / 18 / 19 / 20 / 25 / 26 / 27 / 28 / 66 / 71 / 85; LTE Cat.M1 DL: max. 300 kbps, UL: max. 1.1 Mbps; LTE Cat.NB1 DL: max. 27 kbps, UL: max. 63 kbps; LTE Cat.NB2 DL: max. 124 kbps, UL: max. 158 kbps Short messaging service (SMS) Point-to-point mobile terminated (MT) and mobile originated (MO) Text Mode; Protocol Data Unit (PDU) Mode Localization support GNSS capability (GPS/BeiDou/Galileo/GLONASS) Other Embedded IPv4 and IPv6 TCP/IP stack access; Internet Services: TCP server/client, UDP client, DNS, Ping, HTTP client, FTP client, MQTT client Secure Connection with TLS/DTLS Secure boot Dimensions 66 x 25.4 mm Operating temperature -40° C to +85° C (-104° F to 185°F) Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-cat-m1-nb-iot-gnss-shield.jpg?v=1698678268https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-cat-m1-nb-iot-gnss-shield_front.jpg?v=1698678268,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-cat-m1-nb-iot-gnss-shield_back.jpg?v=1698678268,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-cat-m1-nb-iot-gnss-shield_packaging.jpg?v=1698678268https://www.elektor.com/products/arduino-pro-portenta-cat-m1-nb-iot-gnss-shield?variant=46907245297996 in stock 99.95 9 0 6.9 2 - 4 Werktage 46907087192396 Arduino Pro Portenta H7 Arduino Trade Arduino > Arduino Boards > Bestsellers > Components > Development Boards 7630049202252 Portenta H7 follows the Arduino MKR form factor, but enhanced with the Portenta family 80-pin high-density connector. Program it with high-level languages and AI while performing low-latency operations on its customizable hardware. Portenta H7 simultaneously runs high level code along with real time tasks. The design includes two processors that can run tasks in parallel. For example, is possible to execute Arduino compiled code along with MicroPython one, and have both cores to communicate with one another. The Portenta functionality is two-fold, it can either be running like any other embedded microcontroller board, or as the main processor of an embedded computer. Portenta can easily run processes created with TensorFlow Lite, you could have one of the cores computing a computer vision algorithm on the fly, while the other could be making low-level operations like controlling a motor, or acting as a user interface. Use Portenta when performance is key, among other cases, we envision it to be part of: High-end industrial machinery Laboratory equipment Computer vision PLCs Industry-ready user interfaces Robotics controller Mission-critical devices Dedicated stationary computer High-speed booting computation (ms) Two Parallel Cores H7's main processor is the dual core STM32H747 including a Cortex M7 running at 480 MHz and a Cortex-M4 running at 240 MHz. The two cores communicate via a Remote Procedure Call mechanism that allows calling functions on the other processor seamlessly. Both processors share all the in-chip peripherals and can run: Arduino sketches on top of the ARM Mbed OS Native Mbed applications MicroPython / JavaScript via an interpreter TensorFlow Lite Graphics Accelerator Probably one of the most exciting features of the Portenta H7 is the possibility of connecting an external monitor to build your own dedicated embedded computer with a user interface. This is possible thanks to the STM32H747 processor's on-chip GPU, the Chrom-ART Accelerator. Besides the GPU, the chip includes a dedicated JPEG encoder and decoder. A new standard for pinouts The Portenta family adds two 80-pin high density connectors at the bottom of the board. This ensures scalability for a wide range of applications by simply upgrading your Portenta board to the one suiting your needs. On-board Connectivity The onboard wireless module allows to simultaneously manage WiFi and Bluetooth connectivity. The WiFi interface can be operated as an Access Point, as a Station or as a dual mode simultaneous AP/STA and can handle up to 65 Mbps transfer rate. Bluetooth interface supports Bluetooth Classic and Bluetooth Low Energy. It is also possible to expose a series of different wired interfaces like UART, SPI, or I²C, both through some of the MKR styled connectors, or through the new Arduino industrial 80-pin connector pair. The 80-pin connector pair provides additional features including Ethernet. USB-C Multipurpose Connector The board's programming connector is a USB-C port that can also be used to power the board, as a USB Hub, to connect a DisplayPort monitor, or to deliver power to OTG connected devices. Specifications The Arduino Portenta H7 is based on the STM32H747 microcontroller, XI series. Microcontroller STM32H747XI dual Cortex-M7+M4 32bit low power ARM MCU (datasheet) Radio module Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth (Bluetooth Low Energy. 5 via Cordio stack, Bluetooth Low Energy 4.2 via Arduino Stack) (datasheet) Secure element (default) NXP SE0502 (datasheet) Board power supply (USB/VIN) 5 V Supported battery Li-Po Single Cell, 3.7 V, 700 mAh Minimum (integrated charger) Circuit operating voltage 3.3 V Display connector MIPI DSI host & MIPI D-PHY to interface with low-pin count large display GPU Chrom-ART graphical hardware Accelerator Timers 22x timers and watchdogs UART 4x ports (2 with flow cont... https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7.jpg?v=1698678278https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7_front.jpg?v=1698678278,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7_back.jpg?v=1698678278,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7_packaging.jpg?v=1698678278https://www.elektor.com/products/arduino-pro-portenta-h7?variant=46907087192396 in stock 129.95 3 0 0 2 - 4 Werktage 46907245265228 Arduino Pro Portenta H7 Lite Arduino Trade Arduino > Arduino Boards > Bestsellers > Components > Development Boards 7630049202504 Portenta H7 Lite allows you to build your next smart project. Ever wanted an automated house? Or a smart garden? Well, now it’s easy with the Arduino IoT Cloud compatible boards. It means: you can connect devices, visualize data, control and share your projects from anywhere in the world. The Portenta H7 Lite is very similar to the Portenta H7, that simultaneously can run high level code along with real time tasks thanks to its two processors. It is, for example, possible to execute Arduino compiled code along with MicroPython one and have both cores to communicate with one another. However, the H7 Lite is a low-cost board with H7 functionalities that can be configured to specific use cases. Features Dual Core – Two best-in-class processors in one, running parallel tasks AI on the edge – So powerful it can run AI state machines Customization – The board is highly customizable in volumes High-level programming language support (Micropython) The Portenta H7 Lite offers twofold functionality: it can run either like any other embedded microcontroller board, or as the main processor of an embedded computer. For example, use the Portenta Vision Shield to transform your H7 Lite into an industrial camera capable of performing real-time machine learning algorithms on live video feeds. As the H7 Lite can easily run processes created with TensorFlow Lite, you could have one of the cores computing a computer vision algorithm on the fly, while the other carries out low-level operations like controlling a motor or acting as a user interface. Solutions High-end industrial machinery Laboratory equipment Computer vision PLCs Robotics controllers Mission-critical devices High-speed booting computation (ms) Two Parallel Cores The Portenta H7 Lite’s main processor is the STM32H747 dual core including a Cortex-M7 running at 480 MHz and a Cortex-M4 running at 240 MHz. The two cores communicate via a Remote Procedure Call mechanism that allows calling functions on the other processor seamlessly. Both processors share all the in-chip peripherals and can run: Arduino sketches on top of the ARM Mbed OS Native Mbed applications MicroPython / JavaScript via an interpreter TensorFlow Lite A New Standard for Pinouts The Portenta family adds two 80-pin high-density connectors at the bottom of the board. This ensures scalability for a wide range of applications: simply upgrade your Portenta board to the one suiting your needs. USB-C Multipurpose Connector The board’s programming connector is a USB-C port that can also be used to power the board, as a USB Hub, or to deliver power to OTG connected devices. Arduino IoT Cloud Use your Portenta board on Arduino’s IoT Cloud, a simple and fast way to ensure secure communication for all of your connected Things. Specifications Microcontroller STM32H747XI Dual Cortex-M7+M4 32-bit low power ARM MCU (datasheet) Secure element (default) Microchip ATECC608 Board power supply (USB/VIN) 5 V Supported battery Li-Po Single Cell, 3.7 V, 700 mAh Minimum (integrated charger) Circuit operating voltage 3.3 V Current consumption 2.95 μA in Standby mode (Backup SRAM OFF, RTC/LSE ON) Timers 22x timers and watchdogs UART 4x ports (2 with flow control) Ethernet PHY 10 / 100 Mbps (through expansion port only) SD card Interface for SD card connector (through expansion port only) Operational temperature -40 °C to +85 °C MKR headers Use any of the existing industrial MKR shields on it High-density connectors Two 80-pin connectors will expose all of the board's peripherals to other devices Camera interface 8-bit, up to 80 MHz ADC 3x ADCs with 16-bit max. resolution (up to 36 channels, up to 3.6 MSPS) DAC 2x 12-bit DAC (1 MHz) USB-C Host / Device, High / Full Speed, Power delivery Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7-lite.jpg?v=1698678287https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7-lite_front.jpg?v=1698678287,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7-lite_back.jpg?v=1698678287,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-h7-lite_packaging.jpg?v=1698678287https://www.elektor.com/products/arduino-pro-portenta-h7-lite?variant=46907245265228 in stock 94.95 6 0 6.9 2 - 4 Werktage 46907243659596 Arduino Pro Portenta Machine Control Arduino Trade Arduino > Arduino Accessories > Bestsellers > IoT & LoRa > Platforms 7630049202955 The Portenta Machine Control is a fully-centralized, low-power, industrial control unit able to drive equipment and machinery. It can be programmed using the Arduino framework or other embedded development platforms. Thanks to its computing power, the Portenta Machine Control enables a wide range of predictive maintenance and AI use cases. It enables the collection of real-time data from the factory floor and supports the remote control of equipment, even from the cloud, when desired. Features Shorter Time-To-Market Give new life to existing products Add connectivity for monitoring and control Tailor it to your need, each I/O pin can be configured Make equipment smarter to be ready for the AI revolution Provide security and robustness from the ground up Open new business model opportunity (e.g. servitization) Interact with your equipment with advanced HMI Modular Design for adaptation & upgrades The Portenta Machine Control allows companies to enable new business-as-a-service models by monitoring customer usage of equipment for predictive maintenance and providing valuable production data. The Portenta Machine Control enables industry standard soft-PLC control and is able to connect to a range of external sensors and actuators with isolated digital I/O, 4-20 mA compatible analog I/O, 3 configurable temperature channels, and a dedicated I²C connector. Multiple choices are available for network connectivity, including USB, Ethernet, and WiFi/Bluetooth Low Energy in addition to industry specific protocols such as RS485. All I/O are protected by resettable fuses and onboard power management has been engineered to ensure maximum reliability in harsh environments. The Portenta Machine Control core runs a Portenta H7 microcontroller board (included), a highly reliable design operating at industrial temperature ranges (-40 °C to +85 °C) with a dual-core architecture that doesn’t require any external cooling. The main processor offers the possibility of connecting external Human Machine Interfaces like displays, touch panels, keyboards, joysticks, and mice to enable on-site reconfiguration of state machines and direct manipulation of processes. The Portenta Machine Control’s design addresses a large variety of use scenarios. It is possible to configure a selection of the I/O pins via software. The Portenta Machine Control stands out as a powerful computer to unify and optimize production where one single type of hardware can serve all of your needs. Among other outstanding features are the following: Industrial performance leveraging the power of Portenta boards DIN bar compatible housing Push-in terminals for fast connection Compact device (170 x 90 x 50 mm) Reliable design, operating at industrial temperature rates (-40 °C to +85 °C) with a dual-core architecture that doesn’t require any external cooling Embedded RTC (Real Time Clock) to ensure perfect synchronization of processes Leverage the embedded connectivity without any external parts The Portenta Machine Control can be used in multiple industries, across a wide range of machine types, including: labelling machine, form & seal machine, cartoning machine, gluing machine, electric oven, industrial washer & dryers, mixers, etc. Add the Portenta Machine Control to your existing processes effortlessly and become the owner of your solutions in the market of machines. Specifications Processor STM32H747XI Dual Cortex-M7+M4 32-bit low power Arm MCU (Portenta H7) Input 8 digital 24 VDC 2 channels encoder readings 3 Analog for PT100/J/K temperature probes (3-wire cable with compensation) 3 Analog input (4-20 mA/ 0-10 V/NTC 10K) Output 8 digital 24 VDC up to 0.5 A (short circuit protection) 4 analog 0-10 V (up to 20 mA output per channel) Other I/O 12 programmable digital I/O (24 V logic) Commmunication protocols CAN-BUS Programmable Serial port 232/422/485 Connectivity Eth... https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-machine-control.jpg?v=1698678296https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-machine-control_bottom.jpg?v=1698678296,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-machine-control_view.jpg?v=1698678296,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-machine-control_packaging.jpg?v=1698678296https://www.elektor.com/products/arduino-pro-portenta-machine-control?variant=46907243659596 in stock 359.0 6 0 0 2 - 4 Werktage 46907234419020 Arduino Pro Portenta Max Carrier Arduino Trade Arduino > Arduino Boards > Bestsellers 7630049202269 Max Carrier transforms Portenta modules into single-board computers or reference designs that enable edge AI for high-performance industrial, building automation and robotics applications. Thanks to dedicated high-density connectors, it can be paired with Portenta X8 or H7, allowing you to easily prototype and deploy your industrial projects. This Arduino Pro carrier further augments Portenta connectivity options with Fieldbus, LoRa, Cat-M1 and NB-IoT. Among the many available plug-and-play connectors there are Ethernet, USB-A, audio jacks, microSD, mini-PCIe, FD-CAN and Serial RS232/422/485. Max Carrier can be powered via external supply (6-36 V) or battery via the onboard 18650 Li-ion battery connector with 3.7 V battery charger. Features Easily prototype industrial applications and minimize time to market A powerful carrier exposing Portenta peripherals (e.g. CAN, RS232/422/485, USB, mPCIe) Multiple connectivity options (Ethernet, LoRa, CAT-M1, NB-IoT) MicroSD for data logging operations Integrated audio jacks (line-in, line-out, mic-in) Standalone when battery powered Onboard JTAG debugger via micro-USB (with Portenta H7 only) Specifications Connectors High-Density connectors compatible with Portenta products2x USB-A female connectors1x Gigabit Ethernet connector (RJ45)1x FD-Can on RJ111x mPCIe1x Serial RS232/422/485 on RJ12 Audio 3x audio jacks: stereo line-in/line-out, mic-inSpeaker connector Memory Micro SD Wireless modules Murata CMWX1ZZABZ-078 LoRaSARA-R412M-02B (Cat.M1/NB-IoT) Operating temperatures -40 °C to +85 °C (-40° F to 185 °F) Debugging Onboard JLink OB / Blackmagic probe Power/battery Power Jack for external supply (6-36 V)On-board 18650 Li-ion battery connector with battery charger (3.7 V) Dimensions 101.6 x 101.6 mm (4.0 x 4.0') Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-portenta-max-carrier.jpg?v=1698678306https://www.elektor.com/cdn/shop/files/arduino-portenta-max-carrier_front.jpg?v=1698678306,https://www.elektor.com/cdn/shop/files/arduino-portenta-max-carrier_back.jpg?v=1698678306,https://www.elektor.com/cdn/shop/files/arduino-portenta-max-carrier_package.jpg?v=1698678306https://www.elektor.com/products/arduino-pro-portenta-max-carrier?variant=46907234419020 in stock 439.0 4 0 0 2 - 4 Werktage 46907117764940 Arduino Pro Portenta Vision Shield (Ethernet) Arduino Trade Arduino > Arduino Shields > Bestsellers 7630049202481 Features 324x324 pixels camera sensor: use one of the cores in Portenta to run image recognition algorithms using the OpenMV for Arduino editor 100 Mbps Ethernet connector: get your Portenta H7 connected to the wired Internet 2 onboard microphones for directional sound detection: capture and analyse sound in real-time JTAG connector: perform low-level debugging of your Portenta board or special firmware updates using an external programmer SD-Card connector: store your captured data in the card, or read configuration files The Vision Shield has been designed to fit on top of the Arduino Portenta family. The Portenta boards feature multicore 32-bit ARM Cortex processors running at hundreds of megahertz, with megabytes of program memory and RAM. Portenta boards come with WiFi and Bluetooth. Embedded Computer Vision Made Easy Arduino has teamed up with OpenMV to offer you a free license to the OpenMV IDE, an easy way into computer vision using MicroPython as a programming paradigm. Download the OpenMV for Arduino Editor from our professional tutorials site and browse through the examples we have prepared for you inside the OpenMV IDE. Companies across the whole world are already building their commercial products based on this simple-yet-powerful approach to detect, filter, and classify images, QR codes, and others. Debugging With Professional Tools Connect your Portenta H7 to a professional debugger through the JTAG connector. Use professional software tools like the ones from Lauterbach or Segger on top of your board to debug your code step by step. The Vision Shield exposes the required pins for you to plug in your external JTAG. Camera Himax HM-01B0 camera module Resolution 320 x 320 active pixel resolution with support for QVGA Image sensor High sensitivity 3.6μ BrightSense pixel technology Microphone 2 x MP34DT05 Length 66 mm Width 25 mm Weight 11 gr For more information, check out the tutorials provided by Arduino here. https://www.elektor.com/cdn/shop/files/arduino_portenta_vision_shield_-_overview.jpg?v=1698678311https://www.elektor.com/cdn/shop/files/arduino_portenta_vision_shield_-_top_view.jpg?v=1698678311,https://www.elektor.com/cdn/shop/files/arduino_portenta_vision_shield_-_bottom_view.jpg?v=1698678311https://www.elektor.com/products/arduino-pro-portenta-vision-shield-ethernet?variant=46907117764940 in stock 69.95 28 0 6.9 2 - 4 Werktage 46907244478796 Arduino Pro Portenta Vision Shield LoRa Arduino Trade Arduino > Arduino Shields > Bestsellers > IoT & LoRa > Platforms 7630049202870 The Portenta Vision Shield LoRa brings industry-rated features to your Portenta. This hardware add-on will let you run embedded computer vision applications, connect wirelessly via LoRa to the Arduino Cloud or your own infrastructure, and activate your system upon the detection of sound events. The shield comes with: a 320x320 pixels camera sensor: use one of the cores in Portenta to run image recognition algorithms using the OpenMV for Arduino editor long range 868/915 MHz LoRa wireless connectivity: get your Portenta H7 connected to the Internet of Things with low power consumption two on-board microphones for directional sound detection: capture and analyse sound in real-time JTAG connector: perform low-level debugging of your Portenta board or special firmware updates using an external programmer SD-Card connector: store your captured data in the card, or read configuration files The Vision Shield LoRa has been designed to work with the Arduino Portenta H7. The Portenta boards feature multicore 32-bit ARM Cortex processors running at hundreds of megahertz, with megabytes of program memory and RAM. Portenta boards come with WiFi and Bluetooth. Specifications Camera Himax HM-01B0 camera module (manufacturer site) Resolution 320 x 320 active pixel resolution with support for QVGA Image sensor High sensitivity 3.6μ BrightSense pixel technology Microphone 2x MP34DT05 (datasheet) Connectivity 868/915MHz ABZ-093 LoRa Module with ARM Cortex-M0+ (datasheet) Dimensions 66 x 25 mm Weight 8 g Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-vision-shield-lora.jpg?v=1698678321https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-vision-shield-lora_front.jpg?v=1698678321,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-vision-shield-lora_back.jpg?v=1698678321,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-vision-shield-lora_packaging.jpg?v=1698678321https://www.elektor.com/products/arduino-pro-portenta-vision-shield-lora?variant=46907244478796 in stock 84.95 9 0 6.9 2 - 4 Werktage 46907234386252 Arduino Pro Portenta X8 Arduino Trade Arduino > Arduino Boards 7630049202832 Portenta X8 is a powerful, industrial-grade SOM with Linux OS preloaded onboard, capable of running device-independent software thanks to its modular container architecture. Take advantage of onboard Wi-Fi/Bluetooth Low Energy connectivity to securely perform OS/application OTA updates. It’s basically two industrial products in one, with the power of no less than 9 cores. Leverage the Arduino environment to carry out real-time tasks while Linux takes care of high-performance processing. Portenta X8 features an NXP i.MX 8M Mini Cortex-A53 quad-core, up to 1.8 GHz per core + 1x Cortex-M4 up to 400 MHz, plus the STMicroelectronics STM32H747 dual-core Cortex-M7 up to 480 Mhz +M4 32-bit ARM MCU up to 240 Mhz. Features Two industrial products in one, combining Arduino’s availability of libraries/skills with container-based Linux distribution Outstanding computational density – a total of 9 cores within a compact form factor Multi-processor architecture allowing power-optimized processing Leverage popular programming languages like Python, Java and Ruby among others Real-time I/O and fieldbus/control on a dedicated core Deploy powerful AI algorithms and machine learning on the edge Secure OS/applications updates over-the-air Industrial-grade security at the hardware level, thanks to its crypto chip on dedicated bus Leverage the Arduino ecosystem to expand Portenta capabilities Implement multi-protocol routing with a single module Compatible with other Arduino Portenta products Industrial-Grade Security Portenta X8 has been designed with industrial-grade security in mind. PSA Certified and includes the NXP SE050C2 hardware security element to provide key generation, accelerated crypto operations and secure storage. Awarded Arm SystemReady certification and integrated Parsec services, making it one of the market’s first Cassini Products available to developers. Portenta X8 includes the customizable open-source Linux microPlatform OS, built using best industry practices for end-to-end security, incremental OTA updates and fleet management. Utilizing the cloud-based DevOps platform from Foundries.io to reinvent the way embedded Linux solutions are built, tested, deployed and maintained, the Portenta X8 benefits from Foundries.io continuous update service for cybersecurity. This service guarantees an updated image that contains all vulnerability patches; whilst the approach to containers decouples the operating system from the application, to seamlessly keep the whole system updated. Applications Portenta X8 enables IT professionals, system integrators and consulting firms to build and boost a wide variety of solutions for industrial contexts, and also lends itself to building automation and smart agriculture applications. Connected edge computer for manufacturing Autonomous Guided Vehicles (AGV) Interactive full-HD secure kiosks and digital signage Office & home control systems Navigation and control for smart agriculture Behavioral analytics for offices and factories Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-x8.jpg?v=1698678332https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-x8_front.jpg?v=1698678332,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-x8_back.jpg?v=1698678332,https://www.elektor.com/cdn/shop/files/arduino-pro-portenta-x8_packaging.jpg?v=1698678332https://www.elektor.com/products/arduino-pro-portenta-x8?variant=46907234386252 in stock 239.0 1 0 0 2 - 4 Werktage 47310491746636 Arduino Science Kit Rev3 Arduino Trade Arduino Kits > Bestsellers > Education 7630049204010 Unlock a world of interactive learning with the Science Kit R3's robust hardware and software. With the Arduino Nano RP2040 Connect, Arduino Science Carrier R3, and an impressive array of sensors at your disposal, you'll have everything you need to embark on an exhilarating educational journey. Meanwhile, the Science Journal app effortlessly bridges the gap between theory and practice, facilitating real-time data collection, recording, and interpretation. The kit elevates the learning experience by nurturing an enhanced understanding of complex physics concepts through engaging hands-on experimentation. It promotes scientific literacy and hones critical thinking skills by providing real-world application scenarios. With its intuitive content guide, both teachers and students can navigate through scientific explorations with ease. Features Hands-on experimental learning: perform physical experiments, transforming abstract physics concepts into tangible and interactive experiences. Real-time data collection & analysis: With the integration of the Science Journal app, the kit allows students to collect, record, and interpret real-time data with mobile devices, strengthening their data literacy and scientific inquiry skills. Teacher and student-friendly design: Equipped with a preloaded program, the kit requires no prior knowledge of coding or electronics. It also features Bluetooth connectivity for easy data transmission from the Arduino board to the students' mobile devices. Comprehensive sensor ecosystem: The kit comes with multiple sensors, providing a wide range of data collection possibilities and keeping it adaptable to evolving educational needs. Free guided courses – Explore Physics: Includes an intuitive courses guide that assists teachers and students in using the kit, presenting and analyzing data, and evaluating experimental outcomes. These courses also help students effectively communicate their scientific discoveries. Comprehensive teaching support: With its intuitive guide, the Arduino Science Kit R3 eases the instructional process for teachers. It not only instructs on kit usage, but also assists in data presentation, analysis, and evaluation, ensuring students communicate their scientific discoveries effectively. Specifications Hardware Arduino Nano RP2040 Connect Arduino Science Carrier R3 Embedded sensors: Air quality, temperature, humidity & pressure IMU: 6-axis linear accelerometer, gyroscope, and magnetometer Proximity, ambient light, light color Voltage or electric potential difference Electrical current Electrical resistance Function generators to see and hear the effect of frequency, amplitude, and phase on a sound wave Ambient sound intensity sensor Ports 2x Grove analog inputs (for external temperature-probe sensor) 2x Grove I²C ports (for external distance & ping-echo sensor) 1x Battery JST connector 2x Output ports connected to lower power signal from function generators (future generation) 1x 3.3 V output port and Ground 2x speaker ports connected to function generators Other 50 cm double-ended cable (blue): crocodile clips one end, banana plug the other 20 cm double-ended cable (black): crocodile clips one end, banana plug the other 20 cm double-ended cable (red): crocodile clips one end, banana plug the other VELCRO strips Silicon stands External temperature probe sensor Ultrasonic distance sensor Grove cable 4-pin housing with lock x2 (L=200 mm) USB-C Cable 50 cm double-ended cable (yellow): crocodile clips one end, banana plug the other 2x Speakers Cable for battery holder with JST connector Battery holder for four 1V5 AA batteries https://www.elektor.com/cdn/shop/files/Arduino-Science-Kit-Rev3.jpg?v=1700131477https://www.elektor.com/cdn/shop/files/Arduino-Science-Kit-Rev3_view.jpg?v=1700131485,https://www.elektor.com/cdn/shop/files/Arduino-Science-Kit-Rev3_top.jpg?v=1700131494,https://www.elektor.com/cdn/shop/files/Arduino-Science-Kit-Rev3_open.jpg?v=1700131503https://www.elektor.com/products/arduino-science-kit-rev3?variant=47310491746636 in stock 239.0 10 0 0 2 - 4 Werktage 46907190804812 Arduino Sensor Kit Base Arduino Trade Arduino > Arduino Kits > Bestsellers > Components > Sensors & LiDAR 7630049202979 Grove is an open-source, modulated, and ready-to-use toolset and takes a building block approach to assemble electronics. This Kit includes a Base Shield to which the various Grove modules can be connected both individually, or together in various combinations to create fun and exciting projects. All of the modules use a Grove connector, which connects each of the components to a Base Shield in just a few seconds. The Base Shield can then be mounted onto an Arduino UNO board and can be programmed using the Arduino IDE. Instructions for connecting and programming the different modules are also included in this kit. This kit was elaborated in collaboration with Seeed Studio and provides the Arduino community with the opportunity to build projects with minimal effort of both wiring and coding. This kit acts as a bridge to the world of Grove and provides a flexible way for Makers to extend their projects to include other complex Grove modules. The Kit comes includes access to an online platform with all the instructions required to plug, sketch and play with the different Grove Modules. Please note: This kit does not include the Arduino Uno board. Included 1 Base Shield that is designed to fit on top of an Arduino UNO board. It comes equipped with 16 grove connectors, which, when placed on top of the UNO, provides the functionality to various pins. It includes: 7x digital connections 4x analog connections 4x I²C connections 1x UART connection 10 Grove modules included can be connected to the base shield, either through the digital, analog, or I2C connectors on the shield. Let's take a quick look at them: The LED - a simple LED that can be turned ON or OFF, or dimmed. The button - pushbutton can either be in a HIGH or LOW state. The potentiometer - a variable resistor that increases or decreases resistance when turning its knob. The buzzer - a piezo speaker that is used to produce binary sounds. The light sensor - a photoresistor that reads light intensity. The sound sensor - a tiny microphone that measures sound vibrations. The air pressure sensor - reads air pressure, using the I²C protocol. The temperature sensor - reads temperature and humidity at the same time. The accelerometer - a sensor used for orientation, used for detecting movement. The OLED screen - a screen that values or messages can be printed to. 6 Grove cables allow you to easily connect the modules to the Base Shield without any soldering required. The Arduino Sensor Kit Library is a wrapper that contains links to other libraries related to certain modules such as the accelerometer, air pressure sensor, temperature sensor, and OLED display. This library provides easy-to-use APIs that will help you build a clear mental model of the concepts you will be using. https://www.elektor.com/cdn/shop/files/arduino_sensor_kit_base_-_overview.jpg?v=1698678338https://www.elektor.com/cdn/shop/files/arduino_sensor_kit_base_-_pcb.jpg?v=1698678338,https://www.elektor.com/cdn/shop/files/arduino_sensor_kit_base_-_package.jpg?v=1698678338https://www.elektor.com/products/arduino-sensor-kit-base?variant=46907190804812 in stock 44.95 10 4.9 6.9 2 - 4 Werktage 46907188904268 Arduino Starter Kit (English) Arduino Trade Arduino > Arduino Kits > Bestsellers 7640152111310 Quickly and easily get started with learning electronics using the Arduino Uno Starter Kit, which have a universal appeal to fans at home, businesses, and schools alike. No prior experience is required, as the kits introduce both coding and electronics through fun, engaging, and hands-on projects. You can use the starter kit to teach students about current, voltage, and digital logic as well as the fundamentals of programming. There’s an introduction to sensors and actuators and how to understand both digital and analog signals. Within all this, you’ll be teaching students how to think critically, learn collaboratively, and solve problems. Projects Book GET TO KNOW YOUR TOOLS an introduction to the basics SPACESHIP INTERFACE design the control panel for your starship LOVE-O-METER measure how hot-blooded you are COLOR MIXING LAMP produce any colour with a lamp that uses light as an input MOOD CUE clue people into how you're doing LIGHT THEREMIN create a musical instrument you play by waving your hands KEYBOARD INSTRUMENT play music and make some noise with this keyboard DIGITAL HOURGLASS a light-up hourglass that can stop you from working too much MOTORIZED PINWHEEL a coloured wheel that will make your head spin ZOETROPE create a mechanical animation you can play forward or reverse CRYSTAL BALL a mystical tour to answer all your tough questions KNOCK LOCK tap out the secret code to open the door TOUCHY-FEEL LAMP a lamp that responds to your touch TWEAK THE ARDUINO LOGO control your personal computer from your Arduino HACKING BUTTONS create a master control for all your devices! Included 1 Projects Book (170 pages) 1 Arduino Uno 1 USB cable 1 Breadboard 400 points 70 Solid core jumper wires 1 Easy-to-assemble wooden base 1 9 V battery snap 1 Stranded jumper wires (black) 1 Stranded jumper wires (red) 6 Phototransistor 3 Potentiometer 10 kΩ 10 Pushbuttons 1 Temperature sensor [TMP36] 1 Tilt sensor 1 alphanumeric LCD (16x2 characters) 1 LED (bright white) 1 LED (RGB) 8 LEDs (red) 8 LEDs (green) 8 LEDs (yellow) 3 LEDs (blue) 1 Small DC motor 6/9 V 1 Small servo motor 1 Piezo capsule 1 H-bridge motor driver 1 Optocouplers 2 Mosfet transistors 3 Capacitors 100 uF 5 Diodes 3 Transparent gels 1 Male pins strip (40x1) 20 Resistors 220 Ω 5 Resistors 560 Ω 5 Resistors 1 kΩ 5 Resistors 4.7 kΩ 20 Resistors 10 kΩ 5 Resistors 1 MΩ 5 Resistors 10 MΩ https://www.elektor.com/cdn/shop/files/arduino_starter_kit_english.jpg?v=1698678343https://www.elektor.com/cdn/shop/files/arduino_starter_kit_english_-_back.jpg?v=1698678343,https://www.elektor.com/cdn/shop/files/arduino_starter_kit_english_-_content.jpg?v=1698678343https://www.elektor.com/products/arduino-starter-kit-english?variant=46907188904268 in stock 149.95 8 0 0 2 - 4 Werktage 46907243987276 Arduino Student Kit Arduino Trade Arduino > Arduino Kits > Bestsellers > Education > No Member Discount > Platforms > Sale 7630049202603 The Arduino Student Kit is a hands-on, step-by-step remote learning tool for ages 11+: get started with the basics of electronics, programming, and coding at home. No prior knowledge or experience is necessary as the kit guides you through step by step. Educators can teach their class remotely using the kits, and parents can use the kit as a homeschool tool for their child to learn at their own pace. Everyone will gain confidence in programming and electronics with guided lessons and open experimentation. Learn the basics of programming, coding and electronics including current, voltage, and digital logic. No prior knowledge or experience is necessary as the kit guides you through step by step. You’ll get all the hardware and software you need for one person, making it ideal to use for remote teaching, homeschooling, and for self-learning. There are step-by-step lessons, exercises, and for a complete and in-depth experience, there’s also extra content including invention spotlights, concepts, and interesting facts about electronics, technology, and programming. Lessons and projects can be paced according to individual abilities, allowing them to learn from home at their own level. The kit can also be integrated into different subjects such as physics, chemistry, and even history. In fact, there’s enough content for an entire semester. How educators can use the kit for remote teaching The online platform contains all the content you need to teach remotely: exclusive learning guidance content, tips for remote learning, nine 90-minute lessons, and two open-ended projects. Each lesson builds off the previous one, providing a further opportunity to apply the skills and concepts students have already learned. They also get a logbook to complete as they work through the lessons. The beginning of each lesson provides an overview, estimated completion times, and learning objectives. Throughout each lesson, there are tips and information that will help to make the learning experience easier. Key answers and extension ideas are also provided. How the kit helps parents homeschool their children This is your hands-on, step-by-step remote learning tool that will help your child learn the basics of programming, coding, and electronics at home. As a parent, you don’t need any prior knowledge or experience as you are guided through step-by-step. The kit is linked directly into the curriculum so you can be confident that your children are learning what they should be, and it provides the opportunity for them to become confident in programming and electronics. You’ll also be helping them learn vital skills such as critical thinking and problem-solving. Self-learning with the Arduino Student Kit Students can use this kit to teach themselves the basics of electronics, programming, and coding. As all the lessons follow step-by-step instructions, it’s easy for them to work their way through and learn on their own. They can work at their own pace, have fun with all the real-world projects, and increase their confidence as they go. They don’t need any previous knowledge as everything is clearly explained, coding is pre-written, and there’s a vocabulary of concepts to refer to. The Arduino Student Kit comes with several parts and components that will be used to build circuits while completing the lessons and projects throughout the course. Included in the kit Access code to exclusive online content including learning guidance notes, step-by-step lessons and extra materials such as resources, invention spotlights and a digital logbook with solutions. 1x Arduino Uno 1x USB cable 1x Board mounting base 1x Multimeter 1x 9 V battery snap 1x 9 V battery 20x LEDs (5x red, 5x green, 5x yellow & 5x blue ) 5x Resistors 560 Ω 5x Resistors 220 Ω 1x Breadboard 400 points 1x Resistor 1 kΩ 1x Resistor 10 kΩ 1x Small Servo motor 2x Potentiometers 10 kΩ 2x Knob potentiometers 2x Capacitors 100 uF Solid core jumper wires 5x... https://www.elektor.com/cdn/shop/files/arduino-student-kit.jpg?v=1698678355https://www.elektor.com/cdn/shop/files/arduino-student-kit_packaging-inside.jpg?v=1698678355,https://www.elektor.com/cdn/shop/files/arduino-student-kit_packaging-open.jpg?v=1698678355,https://www.elektor.com/cdn/shop/files/arduino-student-kit_packaging-front.jpg?v=1698678355,https://www.elektor.com/cdn/shop/files/arduino-student-kit_packaging-view.jpg?v=1698678355https://www.elektor.com/products/arduino-student-kit?variant=46907243987276 in stock 104.95 79.95 98 0 6.9 2 - 4 Werktage 46906969981260 Arduino Uno - 45 Projects for Beginners and Experts (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906969981260-has-digital-downloads 978-1-907920-49-3 This book covers a series of exciting and fun projects for the Arduino, such as a silent alarm, people sensor, light sensor, motor control, internet and wireless control (using a radio link). Contrary to many free projects on the internet all projects in this book have been extensively tested and are guaranteed to work!You can use it as a projects book and build more than 45 projects for your own use. The clear explanations, schematics, and pictures of each project make this a fun activity. The pictures are taken of a working project, so you know for sure that they are correct.You can combine the projects in this book to make your own projects. To facilitate this, clear explanations are provided on how the project works and why it has been designed the way it has That way you will learn a lot about the project and the parts used, knowledge that you can use in your own projects.Apart from that, the book can be used as a reference guide. Using the index, you can easily locate projects that serve as examples for the C++ commands and Arduino functionality. Even after you’ve built all the projects in this book, it will still be a valuable reference guide to keep next to your PC. https://www.elektor.com/cdn/shop/files/arduino-uno-projects_ebook.jpg?v=1689084345https://www.elektor.com/products/arduino-uno-45-projects-for-beginners-and-experts-e-book?variant=46906969981260 in stock 27.95 0 4.9 6.9 2 - 4 Werktage 46907244872012 Arduino Uno Experimenting Bundle Elektor Bundles Bundels Arduino > Arduino Kits > Books > Bundles > Components > Kits > No Member Discount > Raspberry Pi | Arduino | ESP 020340 The project book, written by well-known Elektor author Dogan Ibrahim, holds many software- and hardware-based projects especially developed for the Arduino Uno Experimenting Kit. The kit comes with an Arduino Uno board, several LEDs, sensors, actuators, and other components. The purpose of the kit is to make a flying start with hardware and software aspects of projects designed around the Arduino Uno microcontroller system. The projects given in this guide are fully evaluated and working and fully employ all the supplied components. A block diagram, a circuit diagram, an extensive program listing, and a complete program description is given for every project in the guide. Included in the kit 1x Arduino Uno Rev3 board 1x RFID reader module 1x DS1302 clock module 1x 5 V stepper motor 1x '2003' stepper motor drive board 5x Green LED 5x Yellow LED 5x Red LED 2x Rocker switch 1x Flame sensor 1x LM35 sensor module 1x Infrared receiver 3x Light-dependent resistors (LDRs) 1x IR remote controller 1x Breadboard 4x Pushbutton (with four caps) 1x Buzzer 1x Piezo sounder 1x Adjustable resistor (potentiometer) 1x 74HC595 shift register 1x 7-segment display 1x 4-digit 7-segment display 1x 8x8 Dot-matrix display 1x 1602 / I²C LCD module 1x DHT11 Temperature and humidity module 1x Relay module 1x Sound module Set of Dupont cables Set of Breadboard cables 1x Water sensor 1x PS2 Joystick 5x 1 k-ohm resistor 5x 10 k-ohm resistor 5x 220-ohm resistor 1x 4x4 keypad module 1x 9g Servo (25 cm) 1x RFID card 1x RGB module 1x 9 V battery DC jack Project book (237 pages) Over 60 Projects in the Book Hardware Projects with LEDs Blinking LED – using the onboard LED Blinking LED – using an external LED LED flashing SOS Alternately-blinking LEDs Chasing LEDs Chasing LEDs 2 Binary counting LEDs Random flashing LEDs – Christmas lights Button controlled LED Controlling the LED flashing rate – external interrupts Reaction timer LED color wand RGB fixed colors Traffic lights Traffic lights with pedestrian crossings Using the 74HC595 shift register – binary up counter Using the 74HC595 shift register – randomly flashing 8 LEDs Using the 74HC595 shift register – chasing LEDs Using the 74HC595 shift register – turn ON a specified LED Using the 74HC595 shift register – turn ON specified LEDs 7-Segment LED Displays 7-Segment 1-digit LED counter 7-Segment 4-digit multiplexed LED display 7-Segment 4-digit multiplexed LED display counter – timer interrupts 7-Segment 4-digit multiplexed LED display counter – eliminating the leading zeroes 7-Segment 4-digit multiplexed LED display – reaction timer Timer interrupt blinking onboard LED Liquid Crystal Displays (LCDs) Display text on the LCD Scrolling text on the LCD Display custom characters on the LCD LCD based conveyor belt goods counter LCD-based accurate clock using timer interrupts LCD dice Sensors Analog temperature sensor Voltmeter On/Off temperature controller Darkness reminder using a light-dependent resistor (LDR) Tilt detection Water-level sensor Displaying water levels Water level controller Flooding detector with buzzer Sound detection sensor – relay control by hand clapping Flame sensor – fire detection with relay output Temperature and humidity display Generating musical tones with the melody maker The RFID Reader Finding the Tag ID RFID door lock access control with relay The 4x4 Keypad Display the pressed key code on the Serial Monitor Integer calculator with LCD Keypad door security lock with relay The Real-Time Clock (RTC) Module RTC with Serial Monitor RTC with LCD Temperature and humidity display with time stamping The Joystick Reading joystick analog values 8x8 LED Matrix Displaying shapes Motors Test-rotate the servo Servo sweep Joystick-controlled servo Rotate the motor clockwise and then anticlockwise Infrared Receiver and Remote Control... https://www.elektor.com/cdn/shop/files/arduino-uno-experimenting-bundle-new.jpg?v=1698678367https://www.elektor.com/cdn/shop/files/arduino-uno-experimenting-bundle_book.png?v=1698678367,https://www.elektor.com/cdn/shop/files/arduino-uno-experimenting-bundle_uno.jpg?v=1698678367,https://www.elektor.com/cdn/shop/files/arduino-uno-experimenting-bundle_kit-new.jpg?v=1698678367https://www.elektor.com/products/arduino-uno-experimenting-bundle?variant=46907244872012 pre-order 84.95 69.95 42 0 6.9 2 - 4 Werktage 47318763700556 Arduino Uno Experimenting Kit Makerfabs Boards&Kits 7442105131198 With this kit you can built all the projects described in the book 'Mastering the Arduino Uno R4'. The kit comes with several LEDs, sensors, actuators, and other components. The purpose of the kit is to make a flying start with hardware and software aspects of projects designed around the Arduino Uno microcontroller system. Included 1x RFID reader module 1x DS1302 clock module 1x 5 V stepper motor 1x '2003' stepper motor drive board 5x Green LED 5x Yellow LED 5x Red LED 2x Rocker switch 1x Flame sensor 1x LM35 sensor module 1x Infrared receiver 3x Light-dependent resistors (LDRs) 1x IR remote controller 1x Breadboard 4x Pushbutton (with four caps) 1x Buzzer 1x Piezo sounder 1x Adjustable resistor (potentiometer) 1x 74HC595 shift register 1x 7-segment display 1x 4-digit 7-segment display 1x 8x8 Dot-matrix display 1x 1602 / I²C LCD module 1x DHT11 Temperature and humidity module 1x Relay module 1x Sound module Set of Dupont cables Set of Breadboard cables 1x Water sensor 1x PS2 Joystick 5x 1 k-ohm resistor 5x 10 k-ohm resistor 5x 220-ohm resistor 1x 4x4 keypad module 1x 9g Servo (25 cm) 1x RFID card 1x RGB module 1x 9 V battery DC jack https://www.elektor.com/cdn/shop/files/arduino-uno-experimenting-kit.jpg?v=1699464406https://www.elektor.com/products/arduino-uno-experimenting-kit?variant=47318763700556 out of stock 34.95 -17 4.9 6.9 nicht auf Lager 46907207516492 Arduino Uno Mini (Limited Edition) Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR Comparison Websites 7630049203228 Celebrating the Arduino Uno with a miniaturized limited edition The world's favorite development board has gone mini. Everything in this version of the Arduino Uno is unique. Black and gold, finishing, elegant design and packaging, all delivered to the highest standard. A little jewel to celebrate the Arduino community and what we’ve been doing together for all these years. Each item is unique and numbered on the PCB, and includes a hand-signed letter from the founders. It’s a limited edition, so get while it’s in stock! For serious Arduino Uno lovers Arduino Uno Mini Limited Edition is a collector’s item for serious Arduino Lovers: hobbyists, students, makers, reimaginers, dreamers, hopers, fans, engineers, designers, questioners, cake-makers, problem-solvers, puzzlers, gamers, debaters, developers, entrepreneurs, architects, future-shapers, musicians, scientists... 10 million projects based on (official) Uno boards that have contributed to this incredible story. Specifications The Arduino Uno Mini Limited Edition is a microcontroller board based on the ATmega328P. It has 14 digital inputs/outputs (six of which can be used as PWM outputs), six analog inputs, a 16 MHz ceramic resonator, a USB-C connector, and a reset button. Contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable, use a power adapter, or connect a battery to get started. Microcontroller ATmega328P USB connector USB-C Built-in LED Pins 13 Digital I/O Pins 14 Analog Input Pins 6 PWM Pins 6 UART Yes I²C Yes SPI Yes Circuit operating voltage 5 V Input Voltage (limit) 6-12 V Battery connector None DC current per I/O Pin 20 mA DC current for 3.3 V Pin 50 mA Main processor ATmega328P (16 MHz) USB-serial processor ATmega16U2 (16 MHz) Memory ATmega328P 2 KB SRAM, 32 KB Flash, 1 KB EEPROM Weight 8.05 g Dimensions 26.70 x 34.20 mm Downloads Datasheet https://www.elektor.com/cdn/shop/files/arduino-uno-mini-limited-edition.jpg?v=1698678381https://www.elektor.com/cdn/shop/files/arduino-uno-mini-limited-edition_front.jpg?v=1698678381,https://www.elektor.com/cdn/shop/files/arduino-uno-mini-limited-edition_back.jpg?v=1698678381,https://www.elektor.com/cdn/shop/files/arduino-uno-mini-limited-edition_open.jpg?v=1698678381,https://www.elektor.com/cdn/shop/files/arduino-uno-mini-limited-edition_package.jpg?v=1698678381,https://www.elektor.com/cdn/shop/files/arduino-uno-mini-limited-edition_pinout.png?v=1698678381https://www.elektor.com/products/arduino-uno-mini-limited-edition?variant=46907207516492 in stock 54.95 10 0 6.9 2 - 4 Werktage 47310491844940 Arduino Uno R4 Experimenting Bundle Elektor Bundles Bundels Arduino > Arduino Kits > Bundles > Elektor Kits > No Member Discount 020648 The project book, written by well-known Elektor author Dogan Ibrahim, holds many software- and hardware-based projects especially developed for the Arduino Uno Experimenting Kit. The kit comes with the Arduino Uno R4 Minima, several LEDs, sensors, actuators, and other components. The purpose of the kit is to make a flying start with hardware and software aspects of projects designed around the Arduino Uno microcontroller system. The projects given in this guide are fully evaluated and working and fully employ all the supplied components. A block diagram, a circuit diagram, an extensive program listing, and a complete program description is given for every project in the guide. Included 1x Arduino Uno R4 Minima 1x RFID reader module 1x DS1302 clock module 1x 5 V stepper motor 1x '2003' stepper motor drive board 5x Green LED 5x Yellow LED 5x Red LED 2x Rocker switch 1x Flame sensor 1x LM35 sensor module 1x Infrared receiver 3x Light-dependent resistors (LDRs) 1x IR remote controller 1x Breadboard 4x Pushbutton (with four caps) 1x Buzzer 1x Piezo sounder 1x Adjustable resistor (potentiometer) 1x 74HC595 shift register 1x 7-segment display 1x 4-digit 7-segment display 1x 8x8 Dot-matrix display 1x 1602 / I²C LCD module 1x DHT11 Temperature and humidity module 1x Relay module 1x Sound module Set of Dupont cables Set of Breadboard cables 1x Water sensor 1x PS2 Joystick 5x 1 k-ohm resistor 5x 10 k-ohm resistor 5x 220-ohm resistor 1x 4x4 keypad module 1x 9g Servo (25 cm) 1x RFID card 1x RGB module 1x 9 V battery DC jack Project book (326 pages) Over 80 Projects in the Book Hardware Projects with LEDs Blinking LED – using the on-board LED Blinking LED – using an external LED LED flashing SOS Alternately blinking LEDs Chaser-LEDs Chasing LEDs 2 Binary counting LEDs Random flashing LEDs – Christmas lights Button controlled LED Controlling the LED flashing rate – external interrupts Reaction timer LED color wand RGB fixed colors Traffic lights Traffic lights with pedestrian crossings Using the 74HC595 shift register – binary up counter Using the 74HC595 shift register – random flashing 8 LEDs Using the 74HC595 shift register – chasing LEDs Using the 74HC595 shift register – turn ON a specified LED Using the 74HC595 shift register – turn ON specified LEDs 7-Segment LED Displays 7-Segment 1-digit LED counter 7-Segment 4-digit multiplexed LED display 7-Segment 4-digit multiplexed LED display counter – timer interrupts 7-Segment 4-digit multiplexed LED display counter – blanking leading zeroes 7-Segment 4-digit multiplexed LED display – reaction timer Timer interrupt blinking onboard LED Liquid Crystal Displays (LCDs) Display text on the LCD Scrolling text on the LCD Display custom characters on the LCD LCD based conveyor belt goods counter LCD based accurate clock using timer interrupts LCD dice Sensors Analog temperature sensor Voltmeter On/Off temperature controller Darkness reminder – using a light-dependent resistor (LDR) Tilt detection Displaying water level Water level controller Water flooding detector with buzzer Sound detection sensor – control the relay by clapping hands Flame sensor – fire detection with relay output Temperature and humidity display Generating musical tones – melody maker The RFID Reader Finding the Tag ID RFID door lock access with relay The 4x4 Keypad Display the pressed key code on the Serial Monitor Integer calculator with LCD Keypad door security lock with relay The Real-Time Clock (RTC) Module RTC with Serial Monitor RTC with LCD Temperature and humidity display with time stamping Setting and displaying the current time Periodic interrupt every 2 seconds The Joystick Reading analog values from the joystick 8x8 LED Matrix Displaying shapes Motors: Servo and Stepper Test-rotate the servo Servo sweep Joystick-controlled servo Rotate the motor clockw... https://www.elektor.com/cdn/shop/files/arduino-uno-r4-experimenting-bundle.jpg?v=1699287275https://www.elektor.com/cdn/shop/files/arduino-uno-r4-experimenting-bundle_book.jpg?v=1699287275,https://www.elektor.com/cdn/shop/files/arduino-uno-r4-experimenting-bundle_kit.jpg?v=1699287275,https://www.elektor.com/cdn/shop/files/arduino-uno-r4-experimenting-bundle_kit_r4-minima.jpg?v=1699287275https://www.elektor.com/products/arduino-uno-r4-experimenting-bundle?variant=47310491844940 pre-order 89.95 74.95 42 0 6.9 2 - 4 Werktage 47318772384076 Arduino Uno R4 Minima Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR > NEW > No Member Discount Comparison Websites 7630049203907 The Arduino Uno R4 is powered by the Renesas RA4M1 32-bit ARM Cortex-M4 processor, providing a significant boost in processing power, memory, and functionality. The WiFi version comes with an ESP32-S3 WiFi module in addition to the RA4M1, expanding creative opportunities for makers and engineers. The Uno R4 Minima is an affordable option for those who don't need the additional features. The Arduino Uno R4 runs at 48 MHz, which provides a 3x increase over the popular Uno R3. Additionally, SRAM has been upgraded from 2 kB to 32 kB, and flash memory from 32 kB to 256 kB to support more complex projects. Responding to community feedback, the USB port is now USB-C, and the maximum power supply voltage has been raised to 24 V with an enhanced thermal design. The board includes a CAN bus and an SPI port, enabling users to reduce wiring and perform parallel tasks by connecting multiple shields. A 12-bit analog DAC is also provided on the board. The Arduino Uno R4 comes in 2 versions (Minima and WiFi) and offers the following new features compared to the Uno R3: Arduino Uno R4 Minima Arduino Uno R4 WiFi USB-C connector USB-C connector RA4M1 from Renesas (Cortex-M4) RA4M1 from Renesas (Cortex-M4) HID device (emulate a mouse or a keyboard) HID device (emulate a mouse or a keyboard) Improved power section (up to 24 V through VIN) Improved power section (up to 24 V through VIN) CAN bus CAN bus DAC (12 bits) DAC (12 bits) Op amp Op amp WiFi/Bluetooth LE Fully-addressable LED matrix (12x8) Qwiic I²C connector RTC (with support for a buffer battery) Runtime errors diagnostics Model Comparison Uno R3 Uno R4 Minima Uno R4 WiFi Microcontroller Microchip ATmega328P (8-bit AVR RISC) Renesas RA4M1 (32-bit ARM Cortex-M4) Renesas RA4M1 (32-bit ARM Cortex-M4) Operating Voltage 5 V 5 V 5 V Input Voltage 6-20 V 6-24 V 6-24 V Digital I/O Pins 14 14 14 PWM Digital I/O Pins 6 6 6 Analog Input Pins 6 6 6 DC Current per I/O Pin 20 mA 8 mA 8 mA Clock Speed 16 MHz 48 Mhz 48 Mhz Flash Memory 32 KB 256 KB 256 KB SRAM 2 KB 32 KB 32 KB USB USB-B USB-C USB-C DAC (12 bit) – 1 1 SPI 1 2 2 I²C 1 2 2 CAN – 1 1 Op amp – 1 1 SWD – 1 1 RTC – – 1 Qwiic I²C connector – – 1 LED Matrix – – 12x8 (96 red LEDs) LED_BUILTIN 13 13 13 Dimensions 68.6 x 53.4 mm 68.9 x 53.4 mm 68.9 x 53.4 mm Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-uno-r4-minima.jpg?v=1699464752https://www.elektor.com/cdn/shop/files/arduino-uno-r4-minima_top.jpg?v=1699544596,https://www.elektor.com/cdn/shop/files/arduino-uno-r4-minima_back.jpg?v=1699544596https://www.elektor.com/products/arduino-uno-r4-minima?variant=47318772384076 in stock 19.95 19 4.9 6.9 2 - 4 Werktage 47318773236044 Arduino Uno R4 WiFi Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR > NEW > No Member Discount Comparison Websites 7630049204591 The Arduino Uno R4 is powered by the Renesas RA4M1 32-bit ARM Cortex-M4 processor, providing a significant boost in processing power, memory, and functionality. The WiFi version comes with an ESP32-S3 WiFi module in addition to the RA4M1, expanding creative opportunities for makers and engineers. The Uno R4 Minima is an affordable option for those who don't need the additional features. The Arduino Uno R4 runs at 48 MHz, which provides a 3x increase over the popular Uno R3. Additionally, SRAM has been upgraded from 2 kB to 32 kB, and flash memory from 32 kB to 256 kB to support more complex projects. Responding to community feedback, the USB port is now USB-C, and the maximum power supply voltage has been raised to 24 V with an enhanced thermal design. The board includes a CAN bus and an SPI port, enabling users to reduce wiring and perform parallel tasks by connecting multiple shields. A 12-bit analog DAC is also provided on the board. The Arduino Uno R4 comes in 2 versions (Minima and WiFi) and offers the following new features compared to the Uno R3: Arduino Uno R4 Minima Arduino Uno R4 WiFi USB-C connector USB-C connector RA4M1 from Renesas (Cortex-M4) RA4M1 from Renesas (Cortex-M4) HID device (emulate a mouse or a keyboard) HID device (emulate a mouse or a keyboard) Improved power section (up to 24 V through VIN) Improved power section (up to 24 V through VIN) CAN bus CAN bus DAC (12 bits) DAC (12 bits) Op amp Op amp WiFi/Bluetooth LE Fully-addressable LED matrix (12x8) Qwiic I²C connector RTC (with support for a buffer battery) Runtime errors diagnostics Model Comparison Uno R3 Uno R4 Minima Uno R4 WiFi Microcontroller Microchip ATmega328P (8-bit AVR RISC) Renesas RA4M1 (32-bit ARM Cortex-M4) Renesas RA4M1 (32-bit ARM Cortex-M4) Operating Voltage 5 V 5 V 5 V Input Voltage 6-20 V 6-24 V 6-24 V Digital I/O Pins 14 14 14 PWM Digital I/O Pins 6 6 6 Analog Input Pins 6 6 6 DC Current per I/O Pin 20 mA 8 mA 8 mA Clock Speed 16 MHz 48 Mhz 48 Mhz Flash Memory 32 KB 256 KB 256 KB SRAM 2 KB 32 KB 32 KB USB USB-B USB-C USB-C DAC (12 bit) – 1 1 SPI 1 2 2 I²C 1 2 2 CAN – 1 1 Op amp – 1 1 SWD – 1 1 RTC – – 1 Qwiic I²C connector – – 1 LED Matrix – – 12x8 (96 red LEDs) LED_BUILTIN 13 13 13 Dimensions 68.6 x 53.4 mm 68.9 x 53.4 mm 68.9 x 53.4 mm Downloads Datasheet Schematics https://www.elektor.com/cdn/shop/files/arduino-uno-r4-wifi.jpg?v=1699464760https://www.elektor.com/cdn/shop/files/arduino-uno-r4-wifi_top.jpg?v=1699544605,https://www.elektor.com/cdn/shop/files/arduino-uno-r4-wifi_back.jpg?v=1699544606,https://www.elektor.com/cdn/shop/files/arduino-uno-r4-wifi_heart.jpg?v=1699544606https://www.elektor.com/products/arduino-uno-r4-wifi?variant=47318773236044 in stock 29.95 12 4.9 6.9 2 - 4 Werktage 46863962734924 Arduino Uno Rev3 Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR > Components > Development Boards > No Member Discount Comparison Websites 7630049200050 Arduino Uno is an open-source microcontroller board based on the ATmega328P. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator (CSTCE16M0V53-R0), a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. You can tinker with your Uno without worring too much about doing something wrong, worst case scenario you can replace the chip for a few dollars and start over again. 'Uno' means one in Italian and was chosen to mark the release of Arduino Software (IDE) 1.0. The Uno board and version 1.0 of Arduino Software (IDE) were the reference versions of Arduino, now evolved to newer releases. The Uno board is the first in a series of USB Arduino boards, and the reference model for the Arduino platform; for an extensive list of current, past or outdated boards see the Arduino index of boards. Specifications Microcontroller ATmega328P Operating Voltage 5 V Input Voltage (recommended) 7-12 V Input Voltage (limit) 6-20 V Digital I/O Pins 14 (of which 6 provide PWM output) PWM Digital I/O Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader SRAM 2 KB (ATmega328P) EEPROM 1 KB (ATmega328P) Clock Speed 16 MHz LED_BUILTIN 13 Dimensions 68.6 x 53.4 mm Weight 25 g https://www.elektor.com/cdn/shop/products/arduino-uno-r3.png?v=1698678386https://www.elektor.com/cdn/shop/files/arduino-uno-r3_pinout.png?v=1698678386https://www.elektor.com/products/arduino-uno-rev3?variant=46863962734924 in stock 24.95 85 4.9 6.9 2 - 4 Werktage 46907190149452 Arduino Uno Rev3 SMD Arduino Trade Arduino > Arduino Boards > Bestsellers > Comparison Websites DE > Comparison Websites FR > No Member Discount Comparison Websites 7630049200074 The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Additional features coming with the R3 version are: ATmega16U2 instead of 8U2 as a USB-to-Serial converter. 1.0 pinout: added SDA and SCL pins for TWI communication placed near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board and the second one is a not connected pin, that is reserved for future purposes. stronger RESET circuit. Microcontroller ATmega328P Operating Voltage 5 V Input Voltage 7 V - 12 V Digital I/O Pins 14 PWM Pins 6 Analog Input Pins 8 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 32 KB (ATmega328P) of which 0.5 KB used by bootloader SRAM 2 KB EEPROM 1 KB Clock Speed 16 MHz LED_Builtin 13 Length 68.6 mm Width 53.4 mm Weight 25 g https://www.elektor.com/cdn/shop/files/arduino_uno_smd_rev3_-_overview.jpg?v=1698678391https://www.elektor.com/cdn/shop/files/arduino_uno_smd_rev3_-_bottom.jpg?v=1698678391https://www.elektor.com/products/arduino-uno-rev3-smd?variant=46907190149452 in stock 22.95 22 4.9 6.9 2 - 4 Werktage 46907189461324 Arduino Uno WiFi Rev2 Arduino Trade Arduino > Arduino Boards > Bestsellers > NEW 7630049200234 Add this board to a device and you'll be able to connect it to a WiFi network, using its secure ECC608 crypto chip accelerator. The Arduino Uno WiFi is functionally the same as the Arduino Uno Rev3, but with the addition of WiFi / Bluetooth and some other enhancements. It incorporates the brand new ATmega4809 8-bit microcontroller from Microchip and has an onboard IMU (Inertial Measurement Unit) LSM6DS3TR. The Wi-Fi Module is a self-contained SoC with an integrated TCP/IP protocol stack that can provide access to a Wi-Fi network, or act as an access point. The Arduino Uno WiFi Rev.2 has 14 digital input/output pins – 5 that can be used as PWM outputs – 6 analog inputs, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller. Simply connect it to a computer with a USB cable or power it with an AC adapter or battery to get started. Specifications Operating Voltage 5 V Input Voltage 7 V - 12 V Digital I/O 14 Analog Input Pins 6 Analog Input Pins 6 DC Current per I/O Pin 20 mA DC Current for 3.3 V Pin 50 mA Flash Memory 48 KB SRAM 6.144 Bytes EEPROM 256 Bytes Clock Speed 16 MHz Radio Module u-blox NINA-W102 Secure Element ATECC608A Inertial Measurement Unit LSM6DS3TR LED_Builtin 25 Length 101.52 mm Width 53.3 mm Weight 37 g https://www.elektor.com/cdn/shop/files/arduino_uno_wifi_rev2.jpg?v=1698678396https://www.elektor.com/cdn/shop/files/arduino_uno_wifi_rev2_-_bottom.jpg?v=1698678396,https://www.elektor.com/cdn/shop/files/arduino_uno_wifi_rev2_-_package.jpg?v=1698678396https://www.elektor.com/products/arduino-uno-wifi-rev2?variant=46907189461324 in stock 59.95 6 0 6.9 2 - 4 Werktage 47318725198156 Arduino Uno – 45 Projects for Beginners and Experts Elektor Publishing Books Arduino Books > Bestsellers > Books > Raspberry Pi | Arduino | ESP 9781907920493 This book covers a series of exciting and fun projects for the Arduino, such as a silent alarm, people sensor, light sensor, motor control, internet and wireless control (using a radio link). Contrary to many free projects on the internet all projects in this book have been extensively tested and are guaranteed to work!You can use it as a projects book and build more than 45 projects for your own use. The clear explanations, schematics, and pictures of each project make this a fun activity. The pictures are taken of a working project, so you know for sure that they are correct.You can combine the projects in this book to make your own projects. To facilitate this, clear explanations are provided on how the project works and why it has been designed the way it has That way you will learn a lot about the project and the parts used, knowledge that you can use in your own projects.Apart from that, the book can be used as a reference guide. Using the index, you can easily locate projects that serve as examples for the C++ commands and Arduino functionality. Even after you’ve built all the projects in this book, it will still be a valuable reference guide to keep next to your PC. https://www.elektor.com/cdn/shop/files/arduino-uno-projects-3d-1.jpg?v=1699463226https://www.elektor.com/products/arduino-uno-45-projects-for-beginners-and-experts?variant=47318725198156 in stock 34.95 69 4.9 6.9 2 - 4 Werktage 47754418422092 Argon NEO 5 BRED Case for Raspberry Pi 5 Argon Trade Bestsellers > NEW > Raspberry Pi > Raspberry Pi 5 > Raspberry Pi Cases 020788 The Argon NEO 5 is redesigned specifically to meet the high demands of the Raspberry Pi 5. It offers an impressive heat dissipation solution for both passive and active cooling. Aluminum case enclosure with passive cooling fins that act as the heatsink Air intake vents allow for cool air to enter the case 30 mm PWM fan helps with the airflow and push out hot air to exhaust vents Simple and beautifully designed Made with aluminum alloy and polished with a Black & Red finish for stunning aesthetics. Easy assembly for the 3 part case with the Raspberry Pi 5. Small foot print allows to bring it anywhere – or easily mount to your desired station with built in mounting points. Complete access to all ports with the removable top cover. Superior protection & security Space grade aluminum helps protect Raspberry Pi 5 board from physical damage. The case has a screw on top cover to keep the ports safe when not in use. Optional SD card cover to protect your data even further. Native Raspberry Pi 5 board support Integrated power button LED light display https://www.elektor.com/cdn/shop/files/Argon-NEO-5-BRED-Case-for-Raspberry-Pi-5.jpg?v=1710761741https://www.elektor.com/cdn/shop/files/Argon-NEO-5-BRED-Case-for-Raspberry-Pi-5_side.jpg?v=1710761749,https://www.elektor.com/cdn/shop/files/Argon-NEO-5-BRED-Case-for-Raspberry-Pi-5_internal.jpg?v=1710761763,https://www.elektor.com/cdn/shop/files/Argon-NEO-5-BRED-Case-for-Raspberry-Pi-5_ports.jpg?v=1710761774https://www.elektor.com/products/argon-neo-5-bred-case-for-raspberry-pi-5?variant=47754418422092 in stock 24.95 44 4.9 6.9 2 - 4 Werktage 46907167703372 Argon ONE M.2 Case for Raspberry Pi 4 Elektor Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Raspberry Pi > Raspberry Pi Cases Comparison Websites 019828 The Argon ONE M.2 Case ups the ante by providing two full-sized HDMI ports, power management modes that allows for automatic booting, built-in IR support with streamlined options for configuration and integrated M.2 SATA SSD support through the USB 3 ports of the Raspberry Pi 4. Argon ONE M.2 Case extended support for M.2 SATA SSDs allows you to maximize the true potential speeds of your Raspberry Pi 4. You will now be able to boot via an M.2 SATA SSD for faster boot times and larger storage capacity compared to the traditional microSD card. Argon ONE M.2 is UASP supported for the Raspberry Pi 4 which means you can maximize the transfer speeds of your M.2 SATA Drive. It is compatible with any M.2 SATA SSD with Key-B and Key B&M. Features M.2 SATA SSD CompatibilityAccepts any size of M.2 SATA SSD with Key-B or Key-B&M UASP Supported for Raspberry Pi 4Maximizes the high speed data transfers for Raspberry Pi 4 Two Full-Sized HDMIImproves the dual-monitor support of the Raspberry Pi 4 for its video input Power Management ModesOffers 2 power management options with automatic booting or “Always ON Mode” Built-in IR SupportProgrammable IR support to the Raspberry Pi with streamlined options. Works out of the box with the Argon ONE Remote. Active CoolingSoftware Programmable 30 mm FAN via the Argon ONE software Passive CoolingAluminum alloy top case acts as a giant heatsink connected to the CPU of the Raspberry Pi 4 Cable ManagementRepositioned all ports to the back of the Raspberry Pi 4 to highlight its sleek and modern design. https://www.elektor.com/cdn/shop/files/argon-one-m.2-case-for-raspberry-pi-4.jpg?v=1698678404https://www.elektor.com/cdn/shop/files/argon-one-m.2-case-for-raspberry-pi-4_front.jpg?v=1698678404,https://www.elektor.com/cdn/shop/files/argon-one-m.2-case-for-raspberry-pi-4_back.jpg?v=1698678404,https://www.elektor.com/cdn/shop/files/argon-one-m.2-case-for-raspberry-pi-4_usb.jpg?v=1698678404,https://www.elektor.com/cdn/shop/files/argon-one-m.2-case-for-raspberry-pi-4_parts.jpg?v=1698678404https://www.elektor.com/products/argon-one-m-2-case-for-raspberry-pi-4?variant=46907167703372 in stock 64.95 6 0 6.9 2 - 4 Werktage 46906944127308 ARM Microcontroller Interfacing (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906944127308-has-digital-downloads 978-0-905705-91-0 Learn to interface and program hardware devices in a wide range of useful applications, using ARM7 microcontrollers and the C programming language. Examples covered in full detail include a simple LED to a multi-megabyte SD card running the FAT file system.  Features of this book - Build prototype circuits on breadboard or Veroboard and interface to ARM microcontrollers. - A 32-bit ARM7 microcontroller is used in interfacing and software examples. - Interfacing principles apply to other ARM microcontrollers and other non-ARM microcontrollers as well. - Example programs are written in the C programming language. - Use only free or open source software. - Download and install all programming tools from the Internet. - Template project files are provided for easy project creation. Hardware Interface to LEDs, transistors, optocouplers, relays, solenoids, switches, keypads, LCD displays, seven segment displays, DC motors, stepper motors, external analogue signals using the ADC, RS-232, RS-485, TWI, USB, SPI and SD memory cards. Software Once hardware has been interfaced to a microcontroller, software must be written to control the hardware. You will learn how to write programs to operate externally interfaced hardware devices, use timers and interrupts. Also learn how to port FAT file system code for use with an SD memory card, program the PWM to produce an audio sine wave, program the PWM to speed control a DC motor and more. A chapter on more advanced ARM microcontrollers is included with an overview of some of the newest ARM microcontrollers and their features. https://www.elektor.com/cdn/shop/files/15170.main_2.jpg?v=1689083753https://www.elektor.com/cdn/shop/files/arm-microcontroller-interfacing.jpg?v=1696848650https://www.elektor.com/products/arm-microcontroller-interfacing-e-book?variant=46906944127308 in stock 23.95 0 4.9 6.9 2 - 4 Werktage 46906977321292 ARM Microcontroller Projects (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906977321292-has-digital-downloads It is becoming important for microcontroller users to quickly learn and adapt to new technologies and architecture used in high performance 32-bit microcontrollers. Many manufacturers now offer 32-bit microcontrollers as general purpose processors in embedded applications. ARM provide 32 and 64-bit processors mainly for embedded applications. These days, the majority of mobile devices including mobile phones, tablets, and GPS receivers are based on ARM technology. The low cost, low power consumption, and high performance of ARM processors makes them ideal for use in complex communication and mixed signal applications. This e-book makes use of the ARM Cortex-M family of processors in easy-to-follow, practical projects. It gives a detailed introduction to the architecture of the Cortex-M family. Examples of popular hardware and software development kits are described. The architecture of the highly popular ARM Cortex-M processor STM32F107VCT6 is described at a high level, taking into consideration its clock mechanisms, general input/output ports, interrupt sources, ADC and DAC converters, timer facilities, and more. The information provided here should act as a basis for most readers to start using and programming the STM32F107VCT6 microcontroller together with a development kit. Furthermore, the use of the mikroC Pro for ARM integrated development environment (IDE) has been described in detail. This IDE includes everything required to create a project; namely an editor, compiler, simulator, debugger, and device programmer. Although the e-book is based on the STM32F107VCT6 microcontroller, readers should not find it difficult to follow the projects using other ARM processor family members. About the author Prof Dr Dogan Ibrahim has a BSc degree in electronic engineering, an MSc degree in automatic control engineering, and a PhD in digital signal processing. Dogan has worked in many industrial organizations before he returned to academic life. He was the head of computer engineering department and the biomedical engineering department at the Near East University in Cyprus. Dogan is the author of over 50 technical books on microcontrollers, microprocessors and related fields. He is a Chartered electrical engineer and a Fellow of the Institution of Engineering Technology. https://www.elektor.com/cdn/shop/files/arm_microcontroller_projects_ebook.jpg?v=1689084529https://www.elektor.com/products/arm-microcontroller-projects-e-book?variant=46906977321292 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 47571234455884 ARM Microcontrollers 1 (EN) | E-book Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-47571234455884-has-digital-downloads - This E-Book is for hobbyists, students and engineers who want to learn C and how to use an mbed ARM microcontroller in an easy and fun way, without the need for cumbersome software installations.ARM mbed microcontroller NXP LPC1768The projects in this E-Book are meant for beginners in C and ARM microcontrollers. That doesn't mean the projects are simple, but it does mean that they are easy to understand. We use for example USB communications, a subject that is made so easy by the mbed that it is suitable for a beginners book.Cloud technologyThe mbed NXP LPC1768 uses cloud technology, a revolutionary concept in software development. This means you do not need to install software on your PC in order to program the mbed!The only thing you need is a browser such as Microsoft Internet Explorer, and a USB port on your PC. You can get access to your project from any PC anywhere in the world and continue working on it. When you are done a few simple mouse clicks transfer the program to your mbed hardware. Of course you can optionally download the projects and store them on your own PC.Features of this E-BookLearn how to program an mbed ARM microcontroller using cloud technology. No complicated software installation on your PC needed.Learn programming in C by doing fun and interesting projects. No previous experience or knowledge required.Examples of projects in this E-Book: flashing light, timer, light activated switch, digital thermometer, people detector, USB communication, talking microcontroller, debugging, sound switch, and much more - 35 projects in total.Examples of C subjects in this E-Book: variables, commands, functions, program execution, pointers (introduction).What you needA PC with a USB port, internet connection and a browser such as Microsoft Internet Explorer.The free download that contains for example the project source codes.The hardware introduction package to get started quickly, available from Elektor.TipAlso visit the special support page related to this E-Book!Downloads Contents ARM Microcontrollers 1 (Size: 0.22 MB) Software ARM Microcontrollers 1 (Size: 4.23 MB) https://www.elektor.com/cdn/shop/files/arm-microcontrollers_ebook.jpg?v=1705319203https://www.elektor.com/products/arm-microcontrollers-1-en-e-book?variant=47571234455884 in stock 27.5 0 4.9 6.9 2 - 4 Werktage 47571236389196 Artificial Intelligence (E-BOOK) Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-47571236389196-has-digital-downloads - Artificial Intelligence (E-book) https://www.elektor.com/cdn/shop/files/artificial-intelligence_ebook.jpg?v=1705319213https://www.elektor.com/products/artificial-intelligence-e-book?variant=47571236389196 in stock 27.5 0 4.9 6.9 2 - 4 Werktage 46907073298764 Assembly Language Essentials (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Programming has-digital-downloads,variant-46907073298764-has-digital-downloads A Guide to Powerful Programming for Embedded SystemsYou must be a well-rounded professional to excel in the ever-evolving, rapidly developing embedded design and programming industry. Simply put, when it comes to electronics design and programming, the more topics you can master, the more you’ll flourish at your workplace and at your personal workbench. This shouldn’t be a surprise, as the line between the skills of a hardware engineer and software engineer is blurring. The former should have a good grasp of programming in order to build efficient systems. The latter should understand the details of the design (whether it’s a physical or virtual application) for which he or she is writing code. Thus, to be successful, a modern professional electronics engineer must have a solid grasp of both hardware design and programming.Assembly Language Essentials is a matter-of-fact guide to Assembly that will introduce you to the most fundamental programming language of a processor. Unlike other resources about Assembly that focus exclusively on specific processors and platforms, this book uses the architecture of a fictional processor with its own hardware and instruction set. This enables you to consider the importance of Assembly language without having to deal with predetermined hardware or architectural restrictions.You’ll immediately find this thorough introduction to Assembly to be a valuable resource, whether you know nothing about the language or you have used it before. The only prerequisite is that you have a working knowledge of at least one higher-level programming language, such as C or Java.Assembly Language Essentials is an indispensible resource for electronics engineering professionals, academics, and advanced students looking to enhance their programming skills. The book provides the following, and more:An introduction to Assembly language and its functionalitySignificant definitions associated with Assembly language, as well as essential terminology pertaining to higher-level programming languages and computer architectureImportant algorithms that may be built into high-level languages, but must be done the “hard way” in Assembly language — multiplication, division, and polynomial evaluationA presentation of Interrupt Service Routines with examplesA free, downloadable Assembler program for experimenting with Assembly https://www.elektor.com/cdn/shop/files/assembly-language-essentials-pdf.png?v=1689086506https://www.elektor.com/products/assembly-language-essentials-e-book?variant=46907073298764 in stock 24.95 0 4.9 6.9 2 - 4 Werktage 46907077394764 AxiDraw MiniKit 2 - Compact Pen Plotter DIY-Kit Evil Mad Science Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Fun Electronics > Measuring Tools > Platforms > Plotters > Production & Repair Comparison Websites 799422830745 The AxiDraw MiniKit 2 The AxiDraw MiniKit 2 is a special compact addition to the AxiDraw lineup. Designed for lighter-duty applications, It takes up less desk space and less storage space. It's considerably more portable, too. The AxiDraw MiniKit is also the only DIY kit model of AxiDraw that you get to assemble yourself. All other AxiDraw models ship fully assembled, tested, and ready to use.) A Mini Plotter The AxiDraw MiniKit 2 has a working area of about 6 × 4 inches (150 × 100 mm): Big enough to be useful for a wide range of applications including short notes, postcards, and addressing envelopes. It's also ideally suited for use as a signature machine, for signing checks, letters, books, or artwork. Applications The AxiDraw is an extremely versatile machine, designed to serve a wide variety of everyday and specialized drawing and writing needs. You can use it for almost any task that might normally be carried out with a handheld pen. It allows you to use your computer to produce writing that appears to be handmade, complete with the unmistakable appearance of using a real pen (as opposed to an inkjet or laser printer) to address an envelope or sign one's name. And it does so with precision approaching that of a skilled artist, and – just as importantly – using an arm that never gets tired. Specifications Performance Usable pen travel (inches): 6.3 × 4 inches Usable pen travel (millimeters): 160 × 101 mm Vertical pen travel: 0.7 inch (17 mm) Maximum XY travel speed: 10 inches (25 cm) per second Native XY resolution: 2032 steps per inch (80 steps per mm) Reproducibility (XY): Typically better than 0.005 inches (0.1 mm) at low speeds Physical Major structural components are machined, extruded, or folded aluminum, manufactured and anodized in the USA. Holds pens and other drawing instruments up to 5/8' (16 mm) diameter and 25 g weight. Overall dimensions: Approximately 14.25 × 9.25 × 4.25 inches (36 × 23.5 × 11 cm) Maximum height with cable guides: Approximately 9 inches (23 cm) Footprint: Approximately 13.5 × 1.7 inches (35 x 4.5 cm) Weight: 3.2 Lb (1.5 kg) Software Compatible with Mac, Windows, and Linux Drive directly from within Inkscape, using the AxiDraw extension Comprehensive user guide available for download Driver software software free to download and open source Internet access is required to download software Additionally, AxiDraw Merge software available at no cost to AxiDraw owners. Programming interfaces Note: Programming is not required to use the AxiDraw Stand-alone command line interface (CLI) Available AxiDraw Python API RESTful API available for full machine control, stand-alone or accessible by running RoboPaint in the background. Simplified 'GET-only' API available as well, for use in programming environments (such as Scratch, Snap) that permit only retrieval of URLs. Direct EiBotBoard (EBB) command protocol available for use in any programming environment that supports communication with USB-based serial ports. Code that generates SVG files can also be used to (indirectly) control the machine. Included All parts and materials necessary to build the AxiDraw MiniKit 2 writing and drawing machine. Multi-plug power supply with EU adapter USB cable Small Easel (Board and clips) for paper holding Tools needed Scissors or diagonal cutters Small Phillips-head screwdrivers: #0 and #1 sizes Small flat-head screwdriver: 2 mm or 5/64' blade width recommended Miniature pliers (Recommended but not required) Small hobby knife (Recommended but not required) Downloads User Guide https://www.elektor.com/cdn/shop/files/axidraw-minikit-2.jpg?v=1698678430https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_paper.jpg?v=1698678430,https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_side.jpg?v=1698678430,https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_detail.jpg?v=1698678430,https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_right.jpg?v=1698678430,https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_left.jpg?v=1698678430,https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_contents.jpg?v=1698678430,https://www.elektor.com/cdn/shop/files/axidraw-minikit-2_parts.jpg?v=1698678430https://www.elektor.com/products/axidraw-minikit-2-compact-pen-plotter-diy-kit?variant=46907077394764 in stock 549.0 4 0 0 2 - 4 Werktage 1.8 kg 46907161739596 AxiDraw SE/A3 Writing and Drawing Machine Evil Mad Science Trade Comparison Websites DE > Comparison Websites FR > Fun Electronics > Plotters Comparison Websites 799422830714 The AxiDraw SE/A3 has the same extended plotting area as the AxiDraw V3/A3. In place of the central extrusion that makes up the body of that machine, the AxiDraw SE/A3 has a central beam that is CNC machined from a solid billet of 6061-T6 aluminum, and then anodized to a sleek black finish.This heavy, rigid structure – it's a solid block of metal! – provides dramatically better straightness and stiffness, even compared to the already-stiff AxiDraw V3/A3. This design adds mass exactly where you want it: to the non-moving base that forms the X-axis of the machine. In order to keep the weight light where it matters, the moving Y-axis of the AxiDraw SE/A3 uses the same stiff and light custom aluminum extrusion that we use on the AxiDraw V3/A3.Beyond this, the central beam and X-axis of the AxiDraw SE/A3 feature an all-new geometry for the rolling wheels, which provides more stable and uniform motion along the axis.Getting StartedThe AxiDraw comes fully assembled, tested, and ready to use, right out of the box. A universal-input plug-in power supply is included with the AxiDraw, as is a USB cable, and an optional paper-holding easel. Assuming that you've installed the software first, you can be up and plotting within minutes of opening the box. Our comprehensive PDF user guide walks you through every step of the process.To operate AxiDraw, you will need a reasonably modern computer with an available USB port (Mac, Windows or Linux), plus internet access to download necessary software. Pens and paper are not included. (You can use your own; AxiDraw does not require proprietary pens or paper.)AxiDraw is normally controlled through a set of extensions to Inkscape, the excellent, popular and free vector graphics program. Basic operation is much like that of a printer driver: you import or make a drawing in Inkscape, and use the extensions to plot your text or artwork. It's all handled through a straightforward graphical user interface, and works cleanly on Mac, Windows and Linux.SpecificationsPerformanceUsable pen travel (inches): 16.93 × 11.69 inchesUsable pen travel (millimeters): 430 × 297 mmVertical pen travel: 0.7 inch (17 mm)Maximum XY travel speed: 15 inches (38 cm) per secondNative XY resolution: 2032 steps per inch (80 steps per mm)Reproducibility (XY): Typically better than 0.005 inches (0.1 mm) at low speeds.PhysicalMajor structural components are machined and/or folded aluminum.Holds pens and other drawing instruments up to 1' (25.4 mm) diameter.Overall dimensions: Approximately 26 × 19 × 5 inches (66 × 48 × 13 cm)Maximum height with cable guides: Approximately 11 inches (29 cm)Footprint: Approximately 26 × 5 inches (66 x 13 cm)Weight: 8.4 Lb (3.8 kg)SoftwareCompatible with Mac, Windows, and LinuxDrive directly from within Inkscape, using the AxiDraw extension.Comprehensive user guide available for downloadDriver software software free to download and open sourceInternet access is required to download software.Additionally, AxiDraw Merge software available at no cost to AxiDraw owners.Programming interfacesNote: Programming is not required to use the AxiDraw.Stand-alone command line interface (CLI)Available AxiDraw Python APIRESTful API available for full machine control, stand-alone or accessible by running RoboPaint in the background.Simplified 'GET-only' API available as well, for use in programming environments (such as Scratch, Snap) that permit only retrieval of URLs.Direct EiBotBoard (EBB) command protocol available for use in any programming environment that supports communication with USB-based serial ports.Code that generates SVG files can also be used to (indirectly) control the machine.IncludedAxiDraw SE/A3 writing and drawing machine (fully assembled, tested, and ready to use)Multi-plug power supply with EU adapterUSB cableTabloid/A3 Clip Easel (Board and clips) for paper holdingStandard AxiDraw pen clip and XL pen clipItalic pen adapterDownloadsUser Guide https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine.png?v=1698678445https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_type.png?v=1698678445,https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_pen.png?v=1698678445,https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_letter.png?v=1698678445,https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_central-beam-machined.png?v=1698678445,https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_solid-block-of-aliminum.png?v=1698678445,https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_fountain-pen.png?v=1698678445,https://www.elektor.com/cdn/shop/files/axidraw-se-a3-writing-and-drawing-machine_parts.png?v=1698678445https://www.elektor.com/products/axidraw-se-a3-writing-and-drawing-machine?variant=46907161739596 out of stock 849.0 0 0 0 nicht auf Lager 46906970865996 AxiDraw V3 Writing and Drawing Machine Evil Mad Science Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Fun Electronics > Measuring Tools > Platforms > Plotters > Production & Repair Comparison Websites 0799422830691 The AxiDraw is a simple, modern, precise, and versatile pen plotter, capable of writing or drawing on almost any flat surface. It can write with your favorite fountain pens, permanent markers, and other writing implements to handle an endless variety of applications. Its unique design features a writing head that extends beyond the machine, making it possible to draw on objects bigger than the device itself. Designed for high performance AxiDraw V3 is an all-new version of the AxiDraw, redesigned from the ground up for high performance. It features smooth rolling wheels on custom aluminum extrusions, specially designed for high stiffness and light weight. Its sturdy, rigid construction gives it finer quality output and in most applications allows it to operate at up to twice the speed of the previous AxiDraw. Designed for longevity AxiDraw V3 features a new, highly repairable, field-serviceable design for a long life. While no parts on AxiDraw require regular replacement, this new machine is built with a screws not glue design approach throughout, where essentially every component can be replaced by the end user if it should ever become necessary. Applications The AxiDraw is an extremely versatile machine, designed to serve a wide variety of everyday and specialized drawing and writing needs. You can use it for almost any task that might typically be carried out with a handheld pen. It allows you to use your computer to produce writing that appears to be handmade, complete with the unmistakable appearance of using a real pen (as opposed to an inkjet or laser printer) to address an envelope or sign one's name. And it does so with precision approaching that of a skilled artist, and -just as importantly- using an arm that never gets tired. Formal invitations Place cards for formal dining Signing diplomas and other certificates Addressing envelopes and boxes Handwritten wine lists and menus at restaurants Decorating lunch bags Computer generated artwork Technical drawing Thank you notes and cards Writing signatures Specifications Performance Usable pen travel (inches): 11.81 × 8.58 inches (Just over US letter size) Usable pen travel (millimeters): 300 × 218 mm (Just over A4 size) Vertical pen travel: 0.7 inch (17 mm) Maximum XY travel speed: 15 inches (38 cm) per second Native XY resolution: 2032 steps per inch (80 steps per mm) Reproducibility (XY): Typically better than 0.005 inches (0.1 mm) at low speeds. Physical Major structural components are machined and/or folded aluminum. Holds pens and other drawing instruments up to 5/8' (16 mm) diameter. Overall dimensions: Approximately 21.5 × 16 × 4 inches (55 × 40.5 × 10 cm) Maximum height with cable guides: Approximately 8.5 inches (22 cm) Footprint: Approximately 17 × 3.5 inches (43 × 9 cm) Weight: 4.75 Lb (2.2 kg) Software Compatible with Mac, Windows, and Linux Drive directly from within Inkscape, using the AxiDraw extension. Comprehensive user guide available for download. Driver software software free to download and open source Internet access is required to download software. Additionally, AxiDraw Merge software available at no cost to AxiDraw owners. Programming interfaces Note: Programming is not required to use the AxiDraw. Stand-alone command line interface (CLI) Available AxiDraw Python API RESTful API available for full machine control, stand-alone or accessible by running RoboPaint in the background. Simplified 'GET-only' API available as well, for use in programming environments (such as Scratch, Snap) that permit only retrieval of URLs. Direct EiBotBoard (EBB) command protocol available for use in any programming environment that supports communication with USB-based serial ports. Code that generates SVG files can also be used to (indirectly) control the machine. Included AxiDraw V3 writing and drawing machine (fully assembled, tested, and ready to use) Multi-plug power supply... https://www.elektor.com/cdn/shop/files/1_3.jpg?v=1698678467https://www.elektor.com/cdn/shop/files/3_1.jpg?v=1698678467,https://www.elektor.com/cdn/shop/files/5_2.jpg?v=1698678467,https://www.elektor.com/cdn/shop/files/4-b_1.jpg?v=1698678467https://www.elektor.com/products/axidraw-v3-writing-and-drawing-machine?variant=46906970865996 in stock 699.0 18 0 0 2 - 4 Werktage 46907162100044 AxiDraw V3/A3 Writing and Drawing Machine Evil Mad Science Trade Comparison Websites DE > Comparison Websites FR > Fun Electronics > Measuring Tools > Platforms > Plotters > Production & Repair Comparison Websites 799422830707 As compared to the (US Letter/A4 sized) AxiDraw V3, the AxiDraw V3/A3 has extended travel range, designed for use with paper sizes up to and including 11 × 17 inch ('tabloid' or 'ledger') and A3. It can work with any paper up to and including that size, including envelopes, regular US letter (8 1/2 × 11 inch) or A4 (297 × 210 mm) sized paper, note cards, business cards, or a whole array of smaller items. The AxiDraw comes with a mounting easel (board with clips) that can be used for holding paper, cards, and envelopes of various sizes. The AxiDraw V3/A3 also comes standard with AxiDraw Outrigger Feet pre-installed, for greater stance and stability while plotting. The unique design of the AxiDraw features a drawing head that extends beyond the body of the machine, making it possible to also draw on flat objects bigger than the machine itself. For example, you can set it right on top of a box to write an address or add decorations. You can even set it on top of a poster board, chalkboard, or whiteboard to draw graphics in place. The pen holder fits a wide variety of pens, including Sharpie fine and ultra-fine point markers, most rollerball and fountain pens, small-bodied whiteboard markers, and so forth. It can even hold a fountain pen at a proper angle of 45° to the paper. You can also use implements that aren't pens, such as pencils, chalk, charcoal, brushes, and many others. However, you'll get the best results with instruments such as fountain pens and rollerball pens, which do not require the user to apply pressure. Getting Started The AxiDraw comes fully assembled, tested, and ready to use, right out of the box. A universal-input plug-in power supply is included with the AxiDraw, as is a USB cable, and an optional paper-holding easel. Assuming that you've installed the software first, you can be up and plotting within minutes of opening the box. The comprehensive PDF user guide walks you through every step of the process. To operate AxiDraw, you will need a reasonably modern computer with an available USB port (Mac, Windows or Linux), plus internet access to download necessary software. Pens and paper are not included. (You can use your own! AxiDraw does not require proprietary pens or paper.) AxiDraw is normally controlled through a set of extensions to Inkscape, the excellent, popular and free vector graphics program. Basic operation is much like that of a printer driver: you import or make a drawing in Inkscape, and use the extensions to plot your text or artwork. It's all handled through a straightforward graphical user interface, and works cleanly on Mac, Windows and Linux. Specifications Performance Usable pen travel (inches): 16.93 × 11.69 inches Usable pen travel (millimeters): 430 × 297 mm Vertical pen travel: 0.7 inch (17 mm) Maximum XY travel speed: 15 inches (38 cm) per second Native XY resolution: 2032 steps per inch (80 steps per mm) Reproducibility (XY): Typically better than 0.005 inches (0.1 mm) at low speeds. Physical Major structural components are machined and/or folded aluminum. Holds pens and other drawing instruments up to 5/8' (16 mm) diameter. Overall dimensions: Approximately 26 × 18.5 × 4 inches (66 × 47 × 10 cm) Maximum height with cable guides: Approximately 11 inches (29 cm) Footprint: Approximately 26 × 5 inches (66 x 13 cm) Physical weight: 5.5 Lb (2.5 kg) Software Compatible with Mac, Windows, and Linux Drive directly from within Inkscape, using the AxiDraw extension. Comprehensive user guide available for download. Driver software software free to download and open source Internet access is required to download software. Additionally, AxiDraw Merge software available at no cost to AxiDraw owners. Programming interfaces Note: Programming is not required to use the AxiDraw. Stand-alone command line interface (CLI) Available AxiDraw Python API RESTful API available for full machine control, stand-alone or ac... https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine.png?v=1698678458https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_type.png?v=1698678458,https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_pen.png?v=1698678458,https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_writing.png?v=1698678458,https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_letter.png?v=1698678458,https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_address.png?v=1698678458,https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_detail.png?v=1698678458,https://www.elektor.com/cdn/shop/files/axidraw-v3-a3-writing-and-drawing-machine_parts.png?v=1698678458https://www.elektor.com/products/axidraw-v3-a3-writing-and-drawing-machine?variant=46907162100044 out of stock 849.0 0 0 0 nicht auf Lager 46907074969932 Basic Electronics for Beginners Elektor Publishing Books Basics > Bestsellers > Books > Books | Electronics > No Member Discount > Print Books Elektor Print Book 9781907920844 Analogue Electronics and Microcontrollers ProjectsHobbyist electronics can be a fun way to learn new skills that can be helpful to your career. Those who understand the basics of electronics can design their own circuits and projects. However, before you run, you need to learn to walk.It all starts with analogue electronics. You should be familiar with the simple components and circuits and understand their basic behaviors and the issues you may encounter. The best way to do this is through real experiments. Theory alone is not enough. This book offers a large number of practical entry-level circuits, with which everyone can gain the basic experience.Through the widespread introduction of microcontrollers, a new chapter in electronics has begun. Microcontrollers are now performing more and more tasks that were originally solved using discrete components and conventional ICs. Starting out has become easier and easier thanks to platforms including Bascom, Arduino, micro:bit. The book introduces numerous manageable microcontroller applications. It’s now a case of less soldering and more programming. https://www.elektor.com/cdn/shop/files/basic-electronics-for-beginners.png?v=1689086595https://www.elektor.com/products/basic-electronics-for-beginners?variant=46907074969932 in stock 34.95 19.95 175 4.9 6.9 2 - 4 Werktage 47571241140556 Basic Electronics for Beginners (E-book) Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-47571241140556-has-digital-downloads - Analogue Electronics and Microcontrollers ProjectsHobbyist electronics can be a fun way to learn new skills that can be helpful to your career. Those who understand the basics of electronics can design their own circuits and projects. However, before you run, you need to learn to walk.It all starts with analogue electronics. You should be familiar with the simple components and circuits and understand their basic behaviors and the issues you may encounter. The best way to do this is through real experiments. Theory alone is not enough. This book offers a large number of practical entry-level circuits, with which everyone can gain the basic experience.Through the widespread introduction of microcontrollers, a new chapter in electronics has begun. Microcontrollers are now performing more and more tasks that were originally solved using discrete components and conventional ICs. Starting out has become easier and easier thanks to platforms including Bascom, Arduino, micro:bit. The book introduces numerous manageable microcontroller applications. It?s now a case of less soldering and more programming. https://www.elektor.com/cdn/shop/files/basic-electronics-for-beginners-pdf.png?v=1705319322https://www.elektor.com/products/basic-electronics-for-beginners-e-book?variant=47571241140556 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 46907157152076 Basic Kit for Raspberry Pi Pico (Pico included) Kuongshun Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > Pico RP2040 > Raspberry Pi > Raspberry Pi Kits Comparison Websites 019770 Contents Raspberry Pi Pico RP2040 Development Board 30 cm Micro:bit flat USB cable for Smart Car 10-Pin Male to Female Dupont Line Three-leaf Fan Blue Motor Bracket with Screw 3 V DC motor with wire ULN2003 Driver Board Stepper Motor Green 28 mm Leg LED 5 mm Red (1pcs) 28 mm Leg LED 5 mm Green (1pcs) 28 mm Leg LED 5 mm Yellow (1pcs) 28 mm Leg LED 5 mm Blue (1pcs) Resistor 220R 1/4W 1% (1pcs) 400 Points Soldless Breadboard Infrared Obstacle Avoidance Tracking Sensor Module Active Alarm Buzzer Driver Module Low Current Blue 7 Color Flashing LED Module Tachile Switch Module https://www.elektor.com/cdn/shop/files/basic-kit-for-raspberry-pi-pico.png?v=1689088862https://www.elektor.com/cdn/shop/files/basic-kit-for-raspberry-pi-pico_contents.jpg?v=1696852124https://www.elektor.com/products/basic-kit-for-raspberry-pi-pico-pico-included?variant=46907157152076 in stock 34.95 13 4.9 6.9 2 - 4 Werktage 46906968211788 Battery Holder 2xAA with JST-XH Connector Elektor Trade Cables & Wires > Components 018012 Battery Holder 2xAA with JST-XH Connector Do not use with BBC micro:bit https://www.elektor.com/cdn/shop/files/battery-holder-2xaa-with-jst-xh-connector.jpg?v=1689084257https://www.elektor.com/products/battery-holder-2xaa-with-jst-connector?variant=46906968211788 in stock 4.95 1 4.9 6.9 2 - 4 Werktage 46907296743756 Battery Unit for StromPi 3 JOY-iT Trade Bestsellers > Raspberry Pi > Raspberry Pi Accessories > Raspberry Pi Power Supplies 4250236816616 StromPi sends you an e-mail when his backup battery is flat! Technical details Battery type Lithium iron phosphate (LiFePO4) Capacity 1000 mAh Voltage 3.2 V Features Can be plugged directly to the StromPi 3 Charges immediately on StromPi 3 Own protection circuitry Own charging electronics Increased safety, as chemical self-ignition is not possible Significantly longer life than lithium-ion technologies Wide operating temperature range To our customers residing outside Europe: This product is prohibited from shipment by air! https://www.elektor.com/cdn/shop/files/strompi3-battery-elektor.png?v=1698678491https://www.elektor.com/cdn/shop/files/battery-unit-for-strompi-3.jpg?v=1698678491https://www.elektor.com/products/battery-unit-for-strompi-3?variant=46907296743756 in stock 34.95 3 4.9 6.9 2 - 4 Werktage 46906967982412 BBC micro:bit (Book) Elektor Publishing Books Bestsellers > Books > Microcontrollers > Print Books Elektor Print Book 9781907920547 35 Touch Develop & MicroPython Projects The BBC micro:bit is a credit sized computer based on a highly popular and high performance ARM processor. The device is designed by a group of 29 partners for use in computer education in the UK and will be given free of charge to every secondary school student in the UK. The device is based on the Cortex-M0 processor and it measures 4 x 5 cm. It includes several important sensors and modules such as an accelerometer, magnetometer, 25 LEDs, 2 programmable push-button switches, Bluetooth connectivity, micro USB socket, 5 ring type connectors, and a 23-pin edge connector. The device can be powered from its micro USB port by connecting it to a PC, or two external AAA type batteries can be used. This book is about the use of the BBC micro:bit computer in practical projects. The BBC micro:bit computer can be programmed using several different programming languages, such as Microsoft Block Editor, Microsoft Touch Develop, MicroPython, and JavaScript. The book makes a brief introduction to the Touch Develop programming language and the MicroPython programming language. It then gives 35 example working and tested projects using these language. Readers who learn to program in Touch Develop and MicroPython should find it very easy to program using the Block Editor or any other languages. The following are given for each project: Title of the project Description of the project Aim of the project Touch Develop and MicroPython program listings Complete program listings are given for each project. In addition, working principles of the projects are described briefly in each section. Readers are encouraged to go through the projects in the order given in the book. Also available: Kit of parts for the experiments published in this book. This kit contains: 4 x LED, 4 x 270 ohm resistor, 5 x wire (male-female), 2 x wire (male-male), 3 x Button, 3 x 10 kilo-ohm resistor, 1 x TMP36 temperature sensor, 1 x Buzzer, 1 x Light dependent resistor, 1 x RGB LED, 1 x BC337 transistor, 1 x 680 ohm resistor, 1 x 3V DC motor, 1 x ML8511 UV sensor module, 1 x mini servo, 1 x small breadboard, 1 x BBC micro:bit edge connector, 1 x BBC micro:bit adapter board, 1 x mounting plate https://www.elektor.com/cdn/shop/files/bbc-microbit-book.png?v=1689084242https://www.elektor.com/products/bbc-micro-bit-book?variant=46906967982412 in stock 24.95 40 4.9 6.9 2 - 4 Werktage 46906976960844 BBC micro:bit (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906976960844-has-digital-downloads 35 Touch Develop & MicroPython Projects The BBC micro:bit is a credit sized computer based on a highly popular and high performance ARM processor. The device is designed by a group of 29 partners for use in computer education in the UK and will be given free of charge to every secondary school student in the UK. The device is based on the Cortex-M0 processor and it measures 4 x 5 cm. It includes several important sensors and modules such as an accelerometer, magnetometer, 25 LEDs, 2 programmable push-button switches, Bluetooth connectivity, micro USB socket, 5 ring type connectors, and a 23-pin edge connector. The device can be powered from its micro USB port by connecting it to a PC, or two external AAA type batteries can be used. This e-book is about the use of the BBC micro:bit computer in practical projects. The BBC micro:bit computer can be programmed using several different programming languages, such as Microsoft Block Editor, Microsoft Touch Develop, MicroPython, and JavaScript. The e-book makes a brief introduction to the Touch Develop programming language and the MicroPython programming language. It then gives 35 example working and tested projects using these language. Readers who learn to program in Touch Develop and MicroPython should find it very easy to program using the Block Editor or any other languages. The following are given for each project: • Title of the project• Description of the project• Aim of the project• Touch Develop and MicroPython program listingsComplete program listings are given for each project. In addition, working principles of the projects are described briefly in each section. Readers are encouraged to go through the projects in the order given in the e-book. Also available: Kit of parts for the experiments published in this book. This kit contains: 4 x LED, 4 x 270 ohm resistor, 5 x wire (male-female), 2 x wire (male-male), 3 x Button, 3 x 10 kilo-ohm resistor, 1 x TMP36 temperature sensor, 1 x Buzzer, 1 x Light dependent resistor, 1 x RGB LED, 1 x BC337 transistor, 1 x 680 ohm resistor, 1 x 3V DC motor, 1 x ML8511 UV sensor module, 1 x mini servo, 1 x small breadboard, 1 x BBC micro:bit edge connector, 1 x BBC micro:bit adapter board, 1 x mounting plate https://www.elektor.com/cdn/shop/files/bbc-microbit-ebook.jpg?v=1689084516https://www.elektor.com/products/bbc-micro-bit-e-book?variant=46906976960844 in stock 18.95 0 4.9 6.9 2 - 4 Werktage 46907116355916 BBC micro:bit v2 Elektor Trade BBC micro:bit > Bestsellers > Components > Development Boards > Platforms 4250236821153 Differences between micro:bit v1 and micro:bit v2 The BBC micro:bit v2 is equipped with BLE Bluetooth 5.0 It has a Power off button(push and hold power button) MEMS microphone with a LED indicator Onboard speaker Touch-sensitive logo pin LED power indicator A notched edge connector for easier connections. https://www.elektor.com/cdn/shop/files/bbc-microbit-v2.jpg?v=1689087584https://www.elektor.com/cdn/shop/files/bbc-microbit-v2_features.jpg?v=1696851210https://www.elektor.com/products/bbc-micro-bit-v2?variant=46907116355916 in stock 24.95 9 4.9 6.9 2 - 4 Werktage 47571241861452 BeagleV-Fire SBC with RISC-V and FPGA BeagleBoard Trade Bestsellers > Components > Development Boards > FPGA > NEW > Platforms 102110898 BeagleV-Fire is a revolutionary single-board computer (SBC) powered by the Microchip’s PolarFire MPFS025T 5x core RISC-V System on Chip (SoC) with FPGA fabric.BeagleV-Fire opens up new horizons for developers, tinkerers, and the open-source community to explore the vast potential of RISC-V architecture and FPGA technology. It has the same P8 & P9 cape header pins as BeagleBone Black allowing you to stack your favorite BeagleBone cape on top to expand it’s capability.Built around the powerful and energy-efficient RISC-V instruction set architecture (ISA) along with its versatile FPGA fabric, BeagleV-Fire SBC offers unparalleled opportunities for developers, hobbyists, and researchers to explore and experiment with RISC-V technology.Chipset FeaturesMicrochip Polarfire MPFS025T SoC FPGAFPGA Fabric23K logic elements (4-input LUT + DFF)68 Math blocks (18x18 MACC)4 SerDes lanes of 12.7 GbpsMicroprocessor SubsystemProcessor1x 64-bit RV64IMAC monitor/boot core (E51)4x 64-bit RV64GC Application cores (U54-MC)Fmax of 667 MHz (–40°C to 100°C Tj)3.125 CoreMarks/MHz, 1.714 DMIPS/MHzStorageMMC 5.1 SD/SDIO1 Quad SPI flash controller128 KB eNVM56 KB sNVMMemory Interfaces36-bit DDR4/DDR3/LPDDR4/LPDDR3 memory controller with SECDEDCommunication Interfaces2x GigE MACs, USB 2.0 OTG, 5x multi-mode UARTs, 2x SPI, 2x I²C, 2x CAN 2.0 Controllers.2x PCIe Gen2 End Points/Root PortsBoard FeaturesOn-board Memory2 GB LPDDR416 GB Kingston eMMC128 Mbit SPI flashConnectors and ExpansionUSB Type-C with high-Speed (480 Mbps) dual-role support and power inputGigabit EthernetM.2 E-Key socket for WiFi and other PCIe/SDIO modulesmicroSD card socketSYZYGY high-speed connectorCSI 22-pin camera connector2x46-pin BeagleBone Cape add-on headers with on-board ADCScrew terminal for 5 V power input6-pin 3.3 V UART headerJTAG TAG-CONNECT footprintDownloadsDocumentation https://www.elektor.com/cdn/shop/files/BeagleV-Fire.png?v=1709113268https://www.elektor.com/cdn/shop/files/BeagleV-Fire_specs.jpg?v=1709113277https://www.elektor.com/products/beaglev-fire-sbc-with-risc-v-and-fpga?variant=47571241861452 in stock 199.95 5 0 0 2 - 4 Werktage 46907138998604 Benewake TFmini-S LiDAR Sensor (12 m) Benewake Trade Components > NEW > Sensors & LiDAR 019691 TFmini-S is a single-point ranging LiDAR based on TFmini upgrade. The blind zone is shortened to 10cm, the outdoor performance and accuracy of different reflectivity are improved, it can achieve stable, accurate, sensitive and high-frequency range detection. the following points characterize the module: Small size Lightweight Low power consumption High frame rate (up to 1000Hz) Main application scenario: Pedestrian detection Vehicle detection Intelligent barrier gate Altimeter https://www.elektor.com/cdn/shop/files/benewake-tfmini-s-lidar-sensor-12-m.png?v=1698678522https://www.elektor.com/cdn/shop/files/benewake-tfmini-s-lidar-sensor-12-m_side.png?v=1698678522https://www.elektor.com/products/benewake-tfmini-s-lidar-sensor-12-m?variant=46907138998604 out of stock 49.95 0 4.9 6.9 nicht auf Lager 46907023425868 Bernstein 4-620 ESD Screwdriver Set (6 pieces) Bernstein Trade Measuring Tools > No Member Discount > Production & Repair > Tool Kits 4250838504898 Included in the set: Slotted, 50 x 1.2 mm Slotted, 60 x 2.0 mm Slotted, 60 x 3.0 mm Phillips, size 000 Phillips, size 00 Phillips, size 0 All screwdrivers with conductive handle, blade made of chrome vanadium, chrome-plated, with black tip. https://www.elektor.com/cdn/shop/files/4-620-b00-esd-schraubendreher-set-screwdriver_1.jpg?v=1689085630https://www.elektor.com/products/bernstein-4-620-esd-screwdriver-set-6-pieces?variant=46907023425868 out of stock 32.95 24.95 0 4.9 6.9 nicht auf Lager 46906993803596 Black Magic Probe V2.3 - JTAG/SWD ARM Microcontroller Debugger 1 Bit Squared Trade Bestsellers > Programmers & Debuggers 018546 Black Magic Probe V2.3 is a JTAG and SWD Adapter with a built-in GDB server used for programming and debugging ARM Cortex MCUs. Its the best friend of any ARM microcontroller developer. All proceeds from BMP hardware sales go directly into the continued development, maintenance and support of the Open-Source Black Magic Debug project. Black Magic Probe gets rid of intermediate programs like OpenOCD or STLink server. This makes the operation faster and more reliable. You just open your GNU Debugger (GDB) and select the virtual com port offered by BMP23 as your extended remote target. For a full description and how-to visit the project website. Features Wide target IO voltage range support, 1.7 V up to 5 V, thanks to VREF referenced level shifters Power switch allowing supply of 3.3 V to the target through the VREF pin Standard ARM-Cortex 0.05' pitch 10pin debug connector Aux UART capable of up to 2 MBaud Small size (4 x 2 x 1 cm) (1.3 x 0.6 x 0.45'), saving space in your field kit and allowing the use of the debugger in very tight spaces and enclosures Jumpers allowing the connection of the UART TX/RX pins to the JTAG/SWD connector resulting in a 'Unified debug' connector TraceSWO UART, decoding hardware support 16 MByte on board flash AUX connector for accessories Mechanical layout allowing easier use of enclosures and mounting into bigger systems. For example: automated pogopin test equipment, automated Hardware In The Loop (HITL) Continous Integration (CI) systems Improved layout, allowing further improvement of the Black Magic Debug firmware reliability and speed using hardware protocol acceleration Included 1x Black Magic Probe Mini V2.3 (BMP23) 1x JTAG Ribbon Cable 1x 0.1' Header Serial Cable 1x 10-pin ARM Cortexto7-pin Adapter 1x UART 0.1' Cable Dimensions 70 x 17 mm (1.3 x 0.6 in) 3.6 g (0.128 oz) https://www.elektor.com/cdn/shop/files/black-magic-probe-v2.3-jtag-swd-arm-microcontroller-debugger.jpg?v=1689085075https://www.elektor.com/products/black-magic-probe-v2-3-jtag-swd-arm-microcontroller-debugger?variant=46906993803596 in stock 114.95 5 0 0 2 - 4 Werktage 46907220361548 Black Zipper Sleeve Case with Handle for Raspberry Pi 400 Adafruit Trade 5292 This zipper sleeve case is the exact perfect size for a Raspberry Pi 400. Of course, it can also fit other keyboards that are no more than 310 mm (12.2') long and 150 mm (6') wide. Its got a stiff outer layer to protect the delicate electronics from smushing, and soft padding to keep parts cozy on the inside. There's even a grippy handle and an inside mesh pocket that you can use to stash accessories like mice, USB cables, alligator clips, jumper wires, extra batteries, etc! Not too big and not too small, the perfect carrying size and pops easily into a bigger bag, if needed. Comes in classic Adafruit Black. Please note: While the case is roomy and accomodating, we recommend against cramming too many accessories or electronics in the pouch and sleeve. https://www.elektor.com/cdn/shop/files/black-zipper-sleeve-case-with-handle-for-raspberry-pi-400.png?v=1698678541https://www.elektor.com/cdn/shop/files/black-zipper-sleeve-case-with-handle-for-raspberry-pi-400_top.png?v=1698678541,https://www.elektor.com/cdn/shop/files/black-zipper-sleeve-case-with-handle-for-raspberry-pi-400_keyboard.png?v=1698678541,https://www.elektor.com/cdn/shop/files/black-zipper-sleeve-case-with-handle-for-raspberry-pi-400_sleeve.png?v=1698678541https://www.elektor.com/products/black-zipper-sleeve-case-with-handle-for-raspberry-pi-400?variant=46907220361548 out of stock 34.95 0 4.9 6.9 nicht auf Lager 46906985316684 BotFactory SV2 Desktop PCB Printer BotFactory Trade 3D Printers > Business > Measuring Tools > No Member Discount > Platforms > Production & Repair Finer tolerance, higher speed In the development of SV2, we focused on providing finer tolerance, higher speed and larger build area, including 8 mil (200 micron) traces More than 2 layers Finer glue dispensing with Single-part Epoxy An Assembly System supporting 100+ parts as small as 0402, loaded in SMT strips 6' x 6' (150 x 150 mm) working area Interact with SV2 through a web browser, uploading standard Gerber files, image files and centroid-and-rotation files to print and assemble your boards in minutes! Inkjet Printing New inkjet system, featuring more than 300 nozzles and a much smaller droplet size, allowing for thinner lines Larger ink capacity for more boards per cartridge Cleaning station to automatically maintain nozzles and extend cartridge life-span Wider printhead, allowing for an increased sweep across the substrate and faster printing Dispense Finer Compatible with single-part epoxy New motor, gearing and encoder allows for finer control in dispensing process Micro-dispensing tips Cleaning station for automated tip-wiping BotFactory has a vision to revolutionize the electronics industry by bringing the factory to the desktop, creating a world where engineers, researchers and students can prototype printed electronics right there and then. BotFactory SV2 is their latest generation, capable of printing multilayer circuits, dispensing paste and pick-and-placing components within a small, 50 x 50 cm footprint. BotFactory fabricates and assembles printed circuit boards in a way radically different from the familiar, stencil-andetch methods. The conductive traces are printed using a conductive, nanoparticle silver ink onto a substrate (FR-4 or even flexible Kapton®), and then a polymer ink is printed over the traces. Vias are printed using an additive process from the bottom to the top of the board. As CTO and Founder Carlos Ospina explains, “People always ask us ‘how can you create a multilayer circuit without drilling?!’, but at BotFactory we know that drilling is just one of many possible ways to connect a top layer to a bottom one”. Each BotFactory SV2 comes with three heads to perform the printing, dispensing and assembly process. After printing the traces, the printing head is swapped out for the dispensing head and conductive glue deposited onto the pads. The final step is assembly where a pickand-place head equipped with a vacuum pump picks up parts from a tape-strip holder and use an upwards-facing camera to align the part and place it in the correct spot. BotFactory took many lessons from their first product, Squink, and integrated them into SV2. The primary focus was on the printing technology, leveraging new inkjetting methods and curing techniques to print finer conductive traces, thinner insulating ink layers and overall speed. SV2 will be able to print more than two layers with an estimated trace width of 200 microns. Of course, with thinner lines comes finer dispensing, which required a major change to dispensing along with the conductive glues utilized; SV2 will now include a one-part epoxy instead of a two-part as with Squink. Pick-and-place supports 10 times more parts, along with tape-strip packaging and 0402-sized components, allowing users to explore small-batch production from within their workshop. https://www.elektor.com/cdn/shop/files/botfactory-sv2-pcb-printer_1.jpg?v=1698678546https://www.elektor.com/cdn/shop/files/botfactory_sv2_camera_and_tape_tray.jpg?v=1698678546,https://www.elektor.com/cdn/shop/files/botfactory-sv2-disp.jpg?v=1698678546,https://www.elektor.com/cdn/shop/files/botfactory-sv2-dispenser.jpg?v=1698678546https://www.elektor.com/products/botfactory-sv2-desktop-pcb-printer?variant=46906985316684 out of stock 18599.0 0 0 0 nicht auf Lager 46906946421068 Breadboard (830 Tie Points) Elektor Trade Bestsellers > Breadboards > Measuring Tools > Prototyping 017092 Specifications Terminal strip, tie-point 630 Distribution strips, tie-point 200 Solderless breadboard (MB-102) Wire size: Suitable for 20-29 AWG wires, jumper wire of 0.8 mm diameter Material: ABS. Transparent material Size: 16.5 x 5.3 x 0.85 cm Brand new and high quality They allow electronic components to be interconnected in an almost endless number of ways to produce working circuits Because no soldering is required, modifying or revising the circuits can be done quite easily The breadboard consists of a set of formed metal sockets inserted into a durable plastic housing Phosphor bronze nickel plated spring clips Adhesive sheet on the bottom of the board https://www.elektor.com/cdn/shop/files/150237-91c-web.jpg?v=1698678551https://www.elektor.com/cdn/shop/files/150237-91a-web.jpg?v=1698678551,https://www.elektor.com/cdn/shop/files/150237-91b-web.jpg?v=1698678551,https://www.elektor.com/cdn/shop/files/150237-91e-web.jpg?v=1698678551https://www.elektor.com/products/breadboard-830-tie-points?variant=46906946421068 in stock 5.95 38 4.9 6.9 2 - 4 Werktage 46907242905932 Build Your Own Multifunctional 4-Axis CNC Machine Elektor Publishing Books Bestsellers > Books > Books | Hobby & Modelling > Etching & Milling > Measuring Tools > Print Books > Prototyping Elektor Print Book 9783895765278 Plot, Cut, Drill, Mill and Laser with the Z99This book covers the construction, hardware, software, and operation of the Z99 – CNC machine. This is a multifunctional 4-axis machine for home construction.The capabilities of the Z99 machine include:large-format schematic plottingPCB plotting with etch-resist pensschematic plotting with conductive-ink pensletter cutting out of vinylpaper cuttingPCB/substrate drillingPCB/substrate millingtext millinglaser engravinglaser cutting of solder paste masksBy making the support software available as freeware, readers of the book are challenged and encouraged to develop new applications for the Z99.The machine would not be of much use if the user has no option to create suitable files for the designs in mind. A large part of this book is dedicated to creating source files in a variety of freeware software packages, including Inkscape, DesignSpark PCB, KiCad, and FlatCAM.The book is also useful for readers keen to comprehend and then master the basic structure of HPGL, Gerber, Drill, and G-code files, as well as to have a go at deciphering them using software. https://www.elektor.com/cdn/shop/files/build-your-own-multifunctional-4-axis-cnc-machine.png?v=1689091682https://www.elektor.com/products/build-your-own-multifunctional-4-axis-cnc-machine?variant=46907242905932 in stock 29.95 16 4.9 6.9 2 - 4 Werktage 46907243037004 Build Your Own Multifunctional 4-Axis CNC Machine (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907243037004-has-digital-downloads 978-3-89576-528-5 Plot, Cut, Drill, Mill and Laser with the Z99This book covers the construction, hardware, software, and operation of the Z99 – CNC machine. This is a multifunctional 4-axis machine for home construction.The capabilities of the Z99 machine include:large-format schematic plottingPCB plotting with etch-resist pensschematic plotting with conductive-ink pensletter cutting out of vinylpaper cuttingPCB/substrate drillingPCB/substrate millingtext millinglaser engravinglaser cutting of solder paste masksBy making the support software available as freeware, readers of the book are challenged and encouraged to develop new applications for the Z99.The machine would not be of much use if the user has no option to create suitable files for the designs in mind. A large part of this book is dedicated to creating source files in a variety of freeware software packages, including Inkscape, DesignSpark PCB, KiCad, and FlatCAM.The book is also useful for readers keen to comprehend and then master the basic structure of HPGL, Gerber, Drill, and G-code files, as well as to have a go at deciphering them using software. https://www.elektor.com/cdn/shop/files/build-your-own-multifunctional-4-axis-cnc-machine-pdf.png?v=1689091690https://www.elektor.com/products/build-your-own-multifunctional-4-axis-cnc-machine-e-book?variant=46907243037004 in stock 24.95 0 4.9 6.9 2 - 4 Werktage 46907256668492 Building a High-Tech Alarm System with Raspberry Pi Elektor Publishing Books Bestsellers > Books > Print Books > Raspberry Pi > Raspberry Pi Books > Raspberry Pi | Arduino | ESP Elektor Print Book 9783895765513 This book discusses the basic components of any alarm system.All alarm systems have two basic functions. First, they monitor their environment looking for a change such as a door or window opening or someone moving about in the room. Second, they alert the legal owner or user to this change. The system described in this book uses a scanning type software to detect intruders. It behaves like a guard dog, pacing up and down the fence line on the lookout for either an intruder or a familiar person. If you have an alarm key, you can disarm the system and enter.With the scanning method, the software is easy to write and explain. It can scan eight alarm zones plus two special fire zones in about one second.You don’t have to be an electrical engineer to install an alarm system, just a decent carpenter, painter, and plasterer! Because this alarm system runs on 12 volts, you don’t have to be a licensed electrician either to install it. The alarm system presented here uses Python software on the Raspberry Pi combined with some elementary electronic circuits. The code described in the book, as well as CAD files and a bill of materials for the alarm panel, are available for free downloading. The book provides the reader with examples of typical configurations coming straight from the author‘s experience. After reviewing the hardware components typically used in common alarm systems, the author shows how to plan one yourself.To implement a modular alarm, no matter if it is for a single house or for a business or restaurant, the book shows how to skillfully combine a Raspberry Pi with small auxiliary electronic circuits. These are not installation instructions but food for thought that will enable readers to find a solution to their needs. https://www.elektor.com/cdn/shop/files/building-a-high-tech-alarm-system-with-raspberry-pi.png?v=1689092258https://www.elektor.com/products/building-a-high-tech-alarm-system-with-raspberry-pi?variant=46907256668492 in stock 24.95 71 4.9 6.9 2 - 4 Werktage 46907256701260 Building a High-Tech Alarm System with Raspberry Pi (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46907256701260-has-digital-downloads 978-3-89576-552-0 This book discusses the basic components of any alarm system.All alarm systems have two basic functions. First, they monitor their environment looking for a change such as a door or window opening or someone moving about in the room. Second, they alert the legal owner or user to this change. The system described in this book uses a scanning type software to detect intruders. It behaves like a guard dog, pacing up and down the fence line on the lookout for either an intruder or a familiar person. If you have an alarm key, you can disarm the system and enter.With the scanning method, the software is easy to write and explain. It can scan eight alarm zones plus two special fire zones in about one second.You don’t have to be an electrical engineer to install an alarm system, just a decent carpenter, painter, and plasterer! Because this alarm system runs on 12 volts, you don’t have to be a licensed electrician either to install it. The alarm system presented here uses Python software on the Raspberry Pi combined with some elementary electronic circuits. The code described in the book, as well as CAD files and a bill of materials for the alarm panel, are available for free downloading. The book provides the reader with examples of typical configurations coming straight from the author‘s experience. After reviewing the hardware components typically used in common alarm systems, the author shows how to plan one yourself.To implement a modular alarm, no matter if it is for a single house or for a business or restaurant, the book shows how to skillfully combine a Raspberry Pi with small auxiliary electronic circuits. These are not installation instructions but food for thought that will enable readers to find a solution to their needs. https://www.elektor.com/cdn/shop/files/building-a-high-tech-alarm-system-with-raspberry-pi-pdf.png?v=1689092265https://www.elektor.com/products/building-a-high-tech-alarm-system-with-raspberry-pi-e-book?variant=46907256701260 in stock 19.95 0 4.9 6.9 2 - 4 Werktage 47310507344204 Bullseye 10 kHz TCXO LNB for QO-100 RTL-SDR Trade Bestsellers > Radio | SDR 020684 The Bullseye LNB is the world's most precise and stable DTH/consumer Ku-band down converter. Even a VSAT LNBF costing hundreds of dollars more is no match for the performance of the Bullseye 10K LNB. Each unit is calibrated at the factory to within 1 kHz of absolute precision against a GPS-locked spectrum analyzer. Under outdoor conditions, the stability of the LNB is well within 10 kHz of offset. As a bonus feature, the Bullseye 10K provides access to its internal 25 MHz TCXO through the secondary F-connector. This reference output can be used to directly monitor the performance of the TCXO over time. Features Bullseye 10 kHz BE01 Universal single output LNB Frequency stability within 10 kHz in normal outdoor environment Phase locked loop with 2 PPM TCXO Factory calibration within 1 kHz utilizing GPS-locked spectrum analyzers Ultra high precision PLL employing proprietary frequency control system (patent pending) Digitally controlled carrier offset with optional programmer 25 MHz output reference available on secondary F-connector (red) Specifications Input frequency: 10489-12750 MHz LO frequency: 9750/10600 MHz LO frequency stability at 23°C: ±10 kHz LO frequency stability at −20-60°C: ±30 kHz Gain: 50-66 dB Output frequency: 739-1950 MHz (low band) and 1100-2150 MHz (high band) Return loss of 8 dB (739-1950 MHz) and 10 dB (1100-2150 MHz) Noise figure: 0.5 dB https://www.elektor.com/cdn/shop/files/Bullseye-10-kHz-LNB.jpg?v=1704462410https://www.elektor.com/cdn/shop/files/Bullseye-10-kHz-LNB_package.jpg?v=1704462424https://www.elektor.com/products/bullseye-10-khz-tcxo-lnb-for-qo-100?variant=47310507344204 in stock 24.95 59 4.9 6.9 2 - 4 Werktage 46907179204940 Bundle: Getting Started with ESPHome + LILYGO T-Display ESP32 (16 MB) Elektor Bundels Bestsellers > Books > Bundles > ESP > No Member Discount > Print Books Elektor Print Book 019896 About the book Espressif's ESP8266 and ESP32 microcontrollers have brought DIY home automation to the masses. However, not everyone is fluent in programming these microcontrollers with Espressif's C/C++ SDK, the Arduino core, or MicroPython. This is where ESPHome comes into its own: with this project, you don’t program your microcontroller but configure it. This book demonstrates how to create your own home automation devices with ESPHome on an ESP32 microcontroller board. You’ll learn how to combine all kinds of electronic components and automate complex behaviours. Your devices can work completely autonomously, and connect over Wi-Fi to your home automation gateways such as Home Assistant or MQTT broker. By the end of this book, you will be able to create your own custom home automation devices the way you want. Thanks to ESPHome and the ESP32, this is within everyone’s grasp. Set up an ESPHome development environment and create maintainable configurations Use buttons and LEDs Sound a buzzer and play melodies Read measurements from various types of sensors Communicate over a short distance with NFC, infrared light, and Bluetooth Low Energy Show information on various types of displays About the board Chipset Espressif-ESP32 240 MHz Xtensa single-/dual-core 32-bit LX6 microprocessor FLASH QSPI flash 16 MB SRAM 520 kB SRAM Button Reset USB to TTL CP2104 Modular interface UART, SPI, SDIO, I²C, LED PWM, TV PWM, I²S, IRGPIO, ADC, capacitor touch sensor, DACLNA pre-amplifier Display IPS ST7789V 1.14 Inch Working voltage 2.7-4.2 V Working current About 67 MA Sleep current About 350 uA Working temperature range -40℃ ~ +85℃ Size & Weight 51.52 x 25.04 x 8.54 mm (7.81 g) Power Supply USB 5 V/1 A Charging current 500 mA Battery 3.7 V lithium battery JST Connector 2-Pin 1.25 mm USB Connector USB-C https://www.elektor.com/cdn/shop/files/esphome-lilygo-bundle.jpg?v=1698678570https://www.elektor.com/cdn/shop/files/esphome-lilygo-bundle_book.png?v=1698678570,https://www.elektor.com/cdn/shop/files/esphome-lilygo-bundle_board.jpg?v=1698678570https://www.elektor.com/products/bundle-getting-started-with-esphome-lilygo-ttgo-t-display-esp32-16-mb?variant=46907179204940 in stock 54.95 39.95 30 4.9 6.9 2 - 4 Werktage 47662647640396 Bundle: Logic Analyzers in Practice (Book) + USB Logic Analyzer (8-ch, 24 MHz) Elektor Bundles Bundels Bestsellers > Bundles > No Member Discount 020800 PC USB Logic Analyzers with Arduino, Raspberry Pi, and Co. Step-by-step instructions guide you through the analysis of modern protocols such as I²C, SPI, UART, RS-232, NeoPixel, WS28xx, HD44780 and 1-Wire protocols. With the help of numerous experimental circuits based on the Raspberry Pi Pico, Arduino Uno and the Bus Pirate, you will learn the practical application of popular USB logic analyzers. All the experimental circuits presented in this book have been fully tested and are fully functional. The necessary program listings are included – no special programming or electronics knowledge is required for these circuits. The programming languages used are MicroPython and C along with the development environments Thonny and Arduino IDE. This book uses several models of flexible and widely available USB logic analyzers and shows the strengths and weaknesses of each price range. You will learn about the criteria that matter for your work and be able to find the right device for you. Whether Arduino, Raspberry Pi or Raspberry Pi Pico, the example circuits shown allow you to get started quickly with protocol analysis and can also serve as a basis for your own experiments. After reading this book, you will be familiar with all the important terms and contexts, conduct your own experiments, analyze protocols independently, culminating in a comprehensive knowledge set of digital signals and protocols. USB Logic Analyzer (8-ch, 24 MHz) This USB Logic Analyzer is an 8-channel logic analyzer with each input dual purposed for analog data recording. It is perfect for debugging and analyzing signals like I²C, UART, SPI, CAN and 1-Wire. It operates by sampling a digital input connected to a device under test (DUT) at a high sample rate. The connection to the PC is via USB. Specifications Channels 8 digital channels Maximum sampling rate 24 MHz Maximum input voltage 0 V ~ 5 V Operating temperature 0°C ~ 70°C Input impedance 1 MΩ || 10 pF Supported protocols I²C, SPI, UART, CAN, 1-Wire, etc. PC connection USB Dimensions 55 x 28 x 14 mm Downloads Software This bundle contains: New book 'Logic Analyzers in Practice' (normal price: €29.95) USB Logic Analyzer (8-ch, 24 MHz) (normal price: €12.95) USB Cable Jumper Wire Ribbon Cable https://www.elektor.com/cdn/shop/files/Logic-Analyzers-in-Practice-Bundle.png?v=1707213723https://www.elektor.com/products/bundle-logic-analyzers-in-practice-book-usb-logic-analyzer-8-ch-24-mhz?variant=47662647640396 in stock 42.95 34.95 75 4.9 6.9 2 - 4 Werktage 47634495504716 Bundle: Raspberry Pi 5 (4 GB) + Raspberry Pi 5 Essentials (E-book) Elektor Bundles Bundels Bestsellers > Bundles > No Member Discount > Raspberry Pi 5 has-digital-downloads,variant-47634495504716-has-digital-downloads 020798 The new Raspberry Pi 5 delivers more performance than ever before. Thanks to the faster CPU, GPU and RAM, Raspberry Pi 5 is up to 3x faster than its already fast predecessor. In addition to the speed boost, the Raspberry Pi 5 (which features the new Raspberry Pi RP1 silicon for advanced I/O capabilities) also offers the following features for the first time ever: RTC, an on/off button and a PCIe interface. New Features 64-bit quad-core ARM Cortex-A76 processor (2.4 GHz) VideoCore VII GPU (800 MHz) 4 GB of LPDDR4X RAM (4267 MHz) Raspberry Pi silicon RP1 I/O controller chip Real-time clock On/off button PCIe 2.0 UART connector Fan connector Specifications SoC Broadcom BCM2712 CPU ARM Cortex-A76 (ARM v8) 64-bit Clock speed 4x 2.4 GHz GPU VideoCore VII (800 MHz) RAM 4 GB LPDDR4X (4267 MHz) WiFi IEEE 802.11b/g/n/ac (2.4 GHz/5 GHz) Bluetooth Bluetooth 5.0, BLE Ethernet Gigabit Ethernet (with PoE+ support) USB 2x USB-A 3.0 (5 GBit/s)2x USB-A 2.0 PCI Express 1x PCIe 2.0 GPIO Standard 40-pin GPIO header Video 2x micro-HDMI ports (4K60)2x 4-lane MIPI (DSI/CSI) Multimedia H.265 (4K60 decode)OpenGL ES 3.1, Vulkan 1.2 SD card microSD Power 5 V/5 A (via USB-C)Power over Ethernet (PoE+) Raspberry Pi 4 vs Raspberry Pi 5   Raspberry Pi 4 Raspberry Pi 5 SoC Broadcom BCM2711 Broadcom BCM2712 CPU ARM Cortex-A72 (ARM v8) 64-bit ARM Cortex-A76 (ARM v8) 64-bit Clock speed 4x 1.5 GHz 4x 2.4 GHz L2 cache 1 MByte shared 4x 512 KByte L3 cache N/A 2 MByte shared GPU VideoCore VI (500 MHz) VideoCore VII (800 MHz) RAM 4 GB LPDDR4 (3200 MHz) 4 GB LPDDR4X (4267 MHz) WiFi IEEE 802.11b/g/n/ac (2.4 GHz/5 GHz) IEEE 802.11b/g/n/ac (2.4 GHz/5 GHz) Bluetooth Bluetooth 5.0, BLE Bluetooth 5.0, BLE Ethernet Gigabit Ethernet (with PoE support) Gigabit Ethernet (with PoE+ support) USB 2x USB-A 3.02x USB-A 2.0 2x USB-A 3.0 (5 GBit/s)2x USB-A 2.0 I/O controller chip N/A Raspberry Pi Silicon RP1 PCI Express N/A 1x PCIe 2.0 Real Time Clock (RTC) N/A RTC and RTC battery connector On/off button N/A Onboard power button Cooling N/A Fan connector GPIO Standard 40-pin GPIO header Standard 40-pin GPIO header UART via GPIO 1x UART connector SD card microSD slot (DDR50) microSD slot (SDR104) Video 2x micro-HDMI ports (4K60)1x 2-lane MIPI DSI port (display)1x 2-lane MIPI CSI port (camera) 2x micro-HDMI ports (4K60)2x 4-lane MIPI (DSI/CSI) Audio 4-pole 3.5 mm audio jack (stereo audio and composite video) N/A Multimedia H.265 (4K60 decode)H.264 (1080p60 decode, 1080p30 encode)OpenGL ES, 3.0 graphics H.265 (4K60 decode)OpenGL ES 3.1, Vulkan 1.2 Power 5 V/3 A (15 W)Power over Ethernet (PoE) 5 V/5 A (25 W), USB PDPower over Ethernet (PoE+) Downloads Datasheet Raspberry Pi 5 Essentials (E-book) Program, build, and master over 60 projects with Python The Raspberry Pi 5 is the latest single-board computer from the Raspberry Pi Foundation. It can be used in many applications, such as in audio and video media centers, as a desktop computer, in industrial controllers, robotics, and in many domestic and commercial applications. In addition to the well-established features found in other Raspberry Pi computers, the Raspberry Pi 5 offers Wi-Fi and Bluetooth (classic and BLE), which makes it a perfect match for IoT as well as in remote and Internet-based control and monitoring applications. It is now possible to develop many real-time projects such as audio digital signal processing, real-time digital filtering, real-time digital control and monitoring, and many other real-time operations using this tiny powerhouse. The book starts with an introduction to the Raspberry Pi 5 computer and covers the important topics of accessing the computer locally and remotely. Use of the console language commands as well as accessing and using the desktop GUI are described with working examples. The remaining parts of the book cover many Raspberry Pi 5-based hardware projects using components and devices such as LEDs an... https://www.elektor.com/cdn/shop/files/Bundle-Raspberry-Pi-5-4GB-Raspberry-Pi-5-Essentials-Ebook.jpg?v=1706692272https://www.elektor.com/products/bundle-raspberry-pi-5-4-gb-raspberry-pi-5-essentials-e-book?variant=47634495504716 in stock 99.95 79.95 159 0 6.9 2 - 4 Werktage 47634497536332 Bundle: Raspberry Pi 5 (8 GB) + Raspberry Pi 5 Essentials (E-book) Elektor Bundles Bundels Bestsellers > Bundles > No Member Discount > Raspberry Pi 5 has-digital-downloads,variant-47634497536332-has-digital-downloads 020799 The new Raspberry Pi 5 delivers more performance than ever before. Thanks to the faster CPU, GPU and RAM, Raspberry Pi 5 is up to 3x faster than its already fast predecessor. In addition to the speed boost, the Raspberry Pi 5 (which features the new Raspberry Pi RP1 silicon for advanced I/O capabilities) also offers the following features for the first time ever: RTC, an on/off button and a PCIe interface. New Features 64-bit quad-core ARM Cortex-A76 processor (2.4 GHz) VideoCore VII GPU (800 MHz) 8 GB of LPDDR4X RAM (4267 MHz) Raspberry Pi silicon RP1 I/O controller chip Real-time clock On/off button PCIe 2.0 UART connector Fan connector Specifications SoC Broadcom BCM2712 CPU ARM Cortex-A76 (ARM v8) 64-bit Clock speed 4x 2.4 GHz GPU VideoCore VII (800 MHz) RAM 8 GB LPDDR4X (4267 MHz) WiFi IEEE 802.11b/g/n/ac (2.4 GHz/5 GHz) Bluetooth Bluetooth 5.0, BLE Ethernet Gigabit Ethernet (with PoE+ support) USB 2x USB-A 3.0 (5 GBit/s)2x USB-A 2.0 PCI Express 1x PCIe 2.0 GPIO Standard 40-pin GPIO header Video 2x micro-HDMI ports (4K60)2x 4-lane MIPI (DSI/CSI) Multimedia H.265 (4K60 decode)OpenGL ES 3.1, Vulkan 1.2 SD card microSD Power 5 V/5 A (via USB-C)Power over Ethernet (PoE+) Raspberry Pi 4 vs Raspberry Pi 5   Raspberry Pi 4 Raspberry Pi 5 SoC Broadcom BCM2711 Broadcom BCM2712 CPU ARM Cortex-A72 (ARM v8) 64-bit ARM Cortex-A76 (ARM v8) 64-bit Clock speed 4x 1.5 GHz 4x 2.4 GHz L2 cache 1 MByte shared 4x 512 KByte L3 cache N/A 2 MByte shared GPU VideoCore VI (500 MHz) VideoCore VII (800 MHz) RAM 8 GB LPDDR4 (3200 MHz) 8 GB LPDDR4X (4267 MHz) WiFi IEEE 802.11b/g/n/ac (2.4 GHz/5 GHz) IEEE 802.11b/g/n/ac (2.4 GHz/5 GHz) Bluetooth Bluetooth 5.0, BLE Bluetooth 5.0, BLE Ethernet Gigabit Ethernet (with PoE support) Gigabit Ethernet (with PoE+ support) USB 2x USB-A 3.02x USB-A 2.0 2x USB-A 3.0 (5 GBit/s)2x USB-A 2.0 I/O controller chip N/A Raspberry Pi Silicon RP1 PCI Express N/A 1x PCIe 2.0 Real Time Clock (RTC) N/A RTC and RTC battery connector On/off button N/A Onboard power button Cooling N/A Fan connector GPIO Standard 40-pin GPIO header Standard 40-pin GPIO header UART via GPIO 1x UART connector SD card microSD slot (DDR50) microSD slot (SDR104) Video 2x micro-HDMI ports (4K60)1x 2-lane MIPI DSI port (display)1x 2-lane MIPI CSI port (camera) 2x micro-HDMI ports (4K60)2x 4-lane MIPI (DSI/CSI) Audio 4-pole 3.5 mm audio jack (stereo audio and composite video) N/A Multimedia H.265 (4K60 decode)H.264 (1080p60 decode, 1080p30 encode)OpenGL ES, 3.0 graphics H.265 (4K60 decode)OpenGL ES 3.1, Vulkan 1.2 Power 5 V/3 A (15 W)Power over Ethernet (PoE) 5 V/5 A (25 W), USB PDPower over Ethernet (PoE+) Downloads Datasheet Raspberry Pi 5 Essentials (E-book) Program, build, and master over 60 projects with Python The Raspberry Pi 5 is the latest single-board computer from the Raspberry Pi Foundation. It can be used in many applications, such as in audio and video media centers, as a desktop computer, in industrial controllers, robotics, and in many domestic and commercial applications. In addition to the well-established features found in other Raspberry Pi computers, the Raspberry Pi 5 offers Wi-Fi and Bluetooth (classic and BLE), which makes it a perfect match for IoT as well as in remote and Internet-based control and monitoring applications. It is now possible to develop many real-time projects such as audio digital signal processing, real-time digital filtering, real-time digital control and monitoring, and many other real-time operations using this tiny powerhouse. The book starts with an introduction to the Raspberry Pi 5 computer and covers the important topics of accessing the computer locally and remotely. Use of the console language commands as well as accessing and using the desktop GUI are described with working examples. The remaining parts of the book cover many Raspberry Pi 5-based hardware projects using components and devices such as LEDs an... https://www.elektor.com/cdn/shop/files/Bundle-Raspberry-Pi-5-8GB-Raspberry-Pi-5-Essentials-Ebook.jpg?v=1706692802https://www.elektor.com/products/bundle-raspberry-pi-5-8-gb-raspberry-pi-5-essentials-e-book?variant=47634497536332 in stock 124.95 104.95 319 0 0 2 - 4 Werktage 47310491976012 Bundle: Raspberry Pi Zero W + Raspberry Pi and Pico (Special) Elektor Bundles Bundels Bestsellers > Books > Bundles > No Member Discount > Raspberry Pi > Raspberry Pi Books > Raspberry Pi | Arduino | ESP 020585 Raspberry Pi Zero W The Raspberry Pi Zero W extends the Raspberry Pi Zero family. The Raspberry Pi Zero W has all the functionality of the original Raspberry Pi Zero, but comes with added connectivity consisting of: 802.11 b/g/n wireless LAN Bluetooth 4.1 Bluetooth Low Energy (BLE) Other Features 1 GHz, single-core CPU 512 MB RAM Mini HDMI and USB On-The-Go ports Micro-USB power HAT-compatible 40-pin header Composite video and reset headers CSI camera connector Contents of the Special Projects PicoVoiceVoice alienation and sound effects with the Raspberry Pi Pico Navigation with Vibration Feedback POV Display Pulse Width Modulation (PWM) with the Raspberry Pi Pico Wi-Fi with the Raspberry Pi Pico 'Hello World' from the Raspberry Pi Pico and RP2040A look at the Raspberry Pi Foundation’s first microcontroller Simple On-Off Temperature Controller with Raspberry Pi HAT Multitasking with the Raspberry PiShowcase: a traffic lights controller The Raspberry Pi Ruler GadgetFun with a time-of-flight sensor Raspberry Pi Buffer Board (Mk. 1)Never blow up the I/O again FM radio with RDSA top HAT project for the Raspberry Pi LoRa with the Raspberry Pi PicoFun with MicroPython! Tutorials Qt for the Raspberry Pi Raspberry Pi Pico Programmingwith MicroPython and Thonny Raspberry Pi Full StackRPi and RF24 at the heart of a sensor network Raspberry Pi Bash Command Cheat Sheet Community Java on the Raspberry PiAn interview with Frank Delporte Reviews Introducing the New Raspberry Pi Pico W, H, and WH Secure Boot Solution for Raspberry PiRetrofit security at a reasonable price Review: SmartPi – Smart Meter Extension for Raspberry Pi Review: The Enviro+ Raspberry Pi HATMeasuring environmental data with Raspberry Pi and the HAT Enviro+ Review: Meet the Raspberry Pi 4All new but still good? Raspberry Pi Gets a Fast 3.5' Touch DisplayMore power at no extra charge Book Launch: Raspberry Pi for Radio Amateurs This bundle contains: Raspberry Pi Zero W (normal price: €19.95) Elektor Special: Raspberry Pi and Pico (normal price: €14.95) https://www.elektor.com/cdn/shop/files/bundle-zero-w-pico-special-en.jpg?v=1699287131https://www.elektor.com/products/bundle-raspberry-pi-zero-w-raspberry-pi-and-pico-special?variant=47310491976012 in stock 34.95 29.95 118 4.9 6.9 2 - 4 Werktage 46906977648972 C Programming for Embedded Microcontrollers (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906977648972-has-digital-downloads 978-0-905705-80-4 Technology is constantly changing. New microcontrollers become available every year and old ones become redundant. The one thing that has stayed the same is the C programming language used to program these microcontrollers. If you would like to learn this standard language to program microcontrollers, then this book is for you!ARM microcontrollers are available from a large number of manufacturers. They are 32-bit microcontrollers and usually contain a decent amount of memory and a large number of on-chip peripherals. Although this book concentrates on ARM microcontrollers from Atmel, the C programming language applies equally to other manufacturer’s ARMs as well as other microcontrollers.Features of this book:Use only free or open source software.Learn how to download, set up and use free C programming tools.Start learning the C language to write simple PC programs before tackling embedded programming - no need to buy an embedded system right away!Start learning to program from the very first chapter with simple programs and slowly build from there.No programming experience is necessary!Learn by doing - type and run the example programs and exercises.Sample programs and exercises can be downloaded from the Internet.A fun way to learn the C programming language.Ideal for electronic hobbyists, students and engineers wanting to learn the C programming language in an embedded environment on ARM microcontrollers. https://www.elektor.com/cdn/shop/files/c-programming-for-embedded-microcontrollers_ebook.jpg?v=1689084544https://www.elektor.com/products/c-programming-for-embedded-microcontrollers-e-book?variant=46906977648972 in stock 24.95 0 4.9 6.9 2 - 4 Werktage 46907140702540 C Programming on Raspberry Pi Elektor Publishing Books Bestsellers > Books > Print Books > Programming > Raspberry Pi > Raspberry Pi Books > Raspberry Pi | Arduino | ESP Elektor Print Book 9783895764318 Develop innovative hardware-based projects in C The Raspberry Pi has traditionally been programmed using Python. Although this is a very powerful language, many programmers may not be familiar with it. C on the other hand is perhaps the most commonly used programming language and all embedded microcontrollers can be programmed using it. The C language is taught in most technical colleges and universities and almost all engineering students are familiar with using it with their projects. This book is about using the Raspberry Pi with C to develop a range of hardware-based projects. Two of the most popular C libraries, wiringPi and pigpio are used. The book starts with an introduction to C and most students and newcomers will find this chapter invaluable. Many projects are provided in the book, including using Wi-Fi and Bluetooth to establish communication with smartphones. Many sensor and hardware-based projects are included. Both wiringPi and pigpio libraries are used in all projects. Complete program listings are given with full explanations. All projects have been fully tested and work. The following hardware-based projects are provided in the book: Using sensors Using LCDs I²C and SPI buses Serial communication Multitasking External and timer interrupts Using Wi-Fi Webservers Communicating with smartphones Using Bluetooth Sending data to the cloud Program listings of all Raspberry Pi projects developed in this book are available on the Elektor website. Readers can download and use these programs in their projects. Alternatively, they can customize them to suit their applications. https://www.elektor.com/cdn/shop/files/c-programming-on-raspberry-pi.png?v=1689088500https://www.elektor.com/products/c-programming-on-raspberry-pi?variant=46907140702540 in stock 34.95 27 4.9 6.9 2 - 4 Werktage 46907140964684 C Programming on Raspberry Pi (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46907140964684-has-digital-downloads Develop innovative hardware-based projects in C The Raspberry Pi has traditionally been programmed using Python. Although this is a very powerful language, many programmers may not be familiar with it. C on the other hand is perhaps the most commonly used programming language and all embedded microcontrollers can be programmed using it. The C language is taught in most technical colleges and universities and almost all engineering students are familiar with using it with their projects. This book is about using the Raspberry Pi with C to develop a range of hardware-based projects. Two of the most popular C libraries, wiringPi and pigpio are used. The book starts with an introduction to C and most students and newcomers will find this chapter invaluable. Many projects are provided in the book, including using Wi-Fi and Bluetooth to establish communication with smartphones. Many sensor and hardware-based projects are included. Both wiringPi and pigpio libraries are used in all projects. Complete program listings are given with full explanations. All projects have been fully tested and work. The following hardware-based projects are provided in the book: Using sensors Using LCDs I²C and SPI buses Serial communication Multitasking External and timer interrupts Using Wi-Fi Webservers Communicating with smartphones Using Bluetooth Sending data to the cloud Program listings of all Raspberry Pi projects developed in this book are available on the Elektor website. Readers can download and use these programs in their projects. Alternatively, they can customize them to suit their applications. https://www.elektor.com/cdn/shop/files/c-programming-on-raspberry-pi-pdf.png?v=1689088509https://www.elektor.com/products/c-programming-on-raspberry-pi-e-book?variant=46907140964684 in stock 29.95 -3 4.9 6.9 2 - 4 Werktage 46906958414156 C Programming with Arduino Elektor Publishing Books Arduino > Arduino Books > Bestsellers > Books > Print Books > Programming > Raspberry Pi | Arduino | ESP Elektor Print Book 9781907920462 Technology is constantly changing. New microcontrollers become available every year. The one thing that has stayed the same is the C programming language used to program these microcontrollers. If you would like to learn this standard language to program microcontrollers, then this book is for you! Arduino is the hardware platform used to teach the C programming language as Arduino boards are available worldwide and contain the popular AVR microcontrollers from Atmel. Atmel Studio is used as the development environment for writing C programs for AVR microcontrollers. It is a full-featured integrated development environment (IDE) that uses the GCC C software tools for AVR microcontrollers and is free to download. At a glance: Start learning to program from the very first chapter No programming experience is necessary Learn by doing – type and run the example programs A fun way to learn the C programming language Ideal for electronic hobbyists, students and engineers wanting to learn the C programming language in an embedded environment on AVR microcontrollers Use the free full-featured Atmel Studio IDE software for Windows Write C programs for 8-bit AVR microcontrollers as found on the Arduino Uno and MEGA boards Example code runs on Arduino Uno and Arduino MEGA 2560 boards and can be adapted to run on other AVR microcontrollers or boards Use the AVR Dragon programmer / debugger in conjunction with Atmel Studio to debug C programs https://www.elektor.com/cdn/shop/files/c-programming-with-arduino.png?v=1689083999https://www.elektor.com/products/c-programming-with-arduino?variant=46906958414156 in stock 44.95 41 4.9 6.9 2 - 4 Werktage 46906978206028 C Programming with Arduino (E-BOOK) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46906978206028-has-digital-downloads Technology is constantly changing. New microcontrollers become available every year. The one thing that has stayed the same is the C programming language used to program these microcontrollers. If you would like to learn this standard language to program microcontrollers, then this book is for you! Arduino is the hardware platform used to teach the C programming language as Arduino boards are available worldwide and contain the popular AVR microcontrollers from Atmel. Atmel Studio is used as the development environment for writing C programs for AVR microcontrollers. It is a full-featured integrated development environment (IDE) that uses the GCC C software tools for AVR microcontrollers and is free to download. At a glance: Start learning to program from the very first chapter No programming experience is necessary Learn by doing – type and run the example programs A fun way to learn the C programming language Ideal for electronic hobbyists, students and engineers wanting to learn the C programming language in an embedded environment on AVR microcontrollers Use the free full-featured Atmel Studio IDE software for Windows Write C programs for 8-bit AVR microcontrollers as found on the Arduino Uno and MEGA boards Example code runs on Arduino Uno and Arduino MEGA 2560 boards and can be adapted to run on other AVR microcontrollers or boards Use the AVR Dragon programmer / debugger in conjunction with Atmel Studio to debug C programs https://www.elektor.com/cdn/shop/files/c-programming-with-arduino_ebook.jpg?v=1689084564https://www.elektor.com/products/c-programming-with-arduino-e-book?variant=46906978206028 in stock 33.95 0 4.9 6.9 2 - 4 Werktage 46906979811660 C# Programming for Windows and Android (E-BOOK) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906979811660-has-digital-downloads This e-book (pdf), a software-only follow up to the best-selling Elektor Visual Studio C# range of books, is aimed at Engineers, Scientists and Enthusiasts who want to learn about the C# language and development environment.It covers steps from installation, the .NET framework and object oriented programming, through to more advanced concepts including database applications, threading and multi-tasking, internet/network communications and writing DLLs. The DirectX chapters also include video capture. The e-book concludes with several chapters on writing Android applications in C# using the Xamarin add-on.This e-book is based on the Visual Studio 2015 development environment and latest C# additions including WPF applications, LINQ queries, Charts and new commands such as await and async. The latest Visual Studio debugging features (PerfTips, Diagnostic Tool window and IntellTrace) are covered. Finally, the Android chapters include GPS, E-mail and SMS applications.Additionally, the e-book provides free on-line access to extensive, well-documented examples — in a try for yourself style — together with links to the author’s videos, guiding you through the necessary steps to get the expected results. https://www.elektor.com/cdn/shop/files/c_-programming-for-windows-and-android_ebook.jpg?v=1689084608https://www.elektor.com/products/c-programming-for-windows-and-android-e-book?variant=46906979811660 in stock 33.95 0 4.9 6.9 2 - 4 Werktage 46907030602060 Camera Projects Book Elektor Publishing Books Arduino > Arduino Books > Books > Print Books > Raspberry Pi > Raspberry Pi Books > Raspberry Pi | Arduino | ESP Elektor Print Book 9781907920776 39 Experiments with Raspberry Pi and Arduino This book is about Raspberry Pi 3 and Arduino camera projects. The book explains in simple terms and with tested and working example projects, how to configure and use a Raspberry Pi camera and USB based webcam in camera-based projects using a Raspberry Pi. Example projects are given to capture images, create timelapse photography, record video, use the camera and Raspberry Pi in security and surveillance applications, post images to Twitter, record wildlife, stream live video to YouTube, use a night camera, send pictures to smartphones, face and eye detection, colour and shape recognition, number plate recognition, barcode recognition and many more. Installation and use of popular image processing libraries and software including OpenCV, SimpleCV, and OpenALPR are explained in detail using a Raspberry Pi. The book also explains in detail how to use a camera on an Arduino development board to capture images and then save them on a microSD card. All projects given in this book have been fully tested and are working. Program listings for all Raspberry Pi and Arduino projects used in this book are available for download on the Elektor website. https://www.elektor.com/cdn/shop/files/camera-projects-book.png?v=1689085820https://www.elektor.com/products/camera-projects-book?variant=46907030602060 out of stock 29.95 0 4.9 6.9 nicht auf Lager 46907030864204 Camera Projects Book (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46907030864204-has-digital-downloads 978-1-907920-77-6 39 Experiments with Raspberry Pi and Arduino This book is about Raspberry Pi 3 and Arduino camera projects. The book explains in simple terms and with tested and working example projects, how to configure and use a Raspberry Pi camera and USB based webcam in camera-based projects using a Raspberry Pi. Example projects are given to capture images, create timelapse photography, record video, use the camera and Raspberry Pi in security and surveillance applications, post images to Twitter, record wildlife, stream live video to YouTube, use a night camera, send pictures to smartphones, face and eye detection, colour and shape recognition, number plate recognition, barcode recognition and many more. Installation and use of popular image processing libraries and software including OpenCV, SimpleCV, and OpenALPR are explained in detail using a Raspberry Pi. The book also explains in detail how to use a camera on an Arduino development board to capture images and then save them on a microSD card. All projects given in this book have been fully tested and are working. Program listings for all Raspberry Pi and Arduino projects used in this book are available for download on the Elektor website. https://www.elektor.com/cdn/shop/files/camera-projects-book-pdf.png?v=1689085829https://www.elektor.com/products/camera-projects-book-e-book?variant=46907030864204 in stock 24.95 0 4.9 6.9 2 - 4 Werktage 46907249361228 CAN Module MCP2515 Makerfabs Trade Bestsellers > CAN | OBD2 > Components > Measuring Tools > Modules MCI2515CP This CAN Module is based on the CAN bus controller MCP2515 and CAN transceiver TJA1050. With this module, you will easy to control any CAN Bus device by SPI interface with your MCU, such as Arduino Uno and so on. Features Support CAN V2.0B Communication rate up to 1 MB/s Working Voltage: 5 V Working Current: 5 mA Interface: SPI Downloads MCP2515 Datasheet TJA1050 Datasheet https://www.elektor.com/cdn/shop/files/can-module-mcp2515.jpg?v=1698678609https://www.elektor.com/cdn/shop/files/can-module-mcp2515_front.jpg?v=1698678609,https://www.elektor.com/cdn/shop/files/can-module-mcp2515_view.jpg?v=1698678609https://www.elektor.com/products/can-module-mcp2515?variant=46907249361228 in stock 9.95 262 4.9 6.9 2 - 4 Werktage 46907079000396 Carrying Case for SmartScope LabNation Trade Carrying Cases > Measuring Tools 019259 Disguised as an IP66 carrying case, this actually is a phone/tablet stand which allows you to set up your SmartScope environment in a breeze! With rubber bottom pads to prevent sliding, controlling your SmartScope on the road has ever been easier and more comfortable. On the inside this box has plenty of room to fit your SmartScope, tablet, cables and accessories. https://www.elektor.com/cdn/shop/files/case-for-smartscope.jpg?v=1698678615https://www.elektor.com/cdn/shop/files/case-for-smartscope_open.jpg?v=1698678615,https://www.elektor.com/cdn/shop/files/case-for-smartscope_screen.jpg?v=1698678615https://www.elektor.com/products/carrying-case-for-smartscope?variant=46907079000396 out of stock 37.95 0 4.9 6.9 nicht auf Lager 46906972602700 Case for 7" RGB-Touch-Display for Raspberry Pi JOY-iT Trade Bestsellers > Displays > No Member Discount > Raspberry Pi > Raspberry Pi Displays 4250236815534 Case for 7' RGB-Touch-Display for Raspberry Pi https://www.elektor.com/cdn/shop/files/case-for-touch-display-for-rpi-7-inch-back.jpg?v=1698676379https://www.elektor.com/cdn/shop/files/case-for-touch-display-for-rpi-7-inch.jpg?v=1698676379https://www.elektor.com/products/case-for-7-inch-touch-display-for-raspberry-pi?variant=46906972602700 in stock 12.95 6.95 93 4.9 6.9 2 - 4 Werktage 46907068350796 CH340 USB to TTL Converter UART Module CH340G (3.3 V/5.5 V) Elektor Trade Cables & Wires > Components 019151 Features Built-in USB to TTL transfer chip TTL interface output, easy to connect to the MCU Status LED Dual 3.3 V and 5 V power output, working with 3.3 V and 5 V target device Size: 55 x 16 mm https://www.elektor.com/cdn/shop/files/ch340_usb_to_ttl_converter_uart_module_ch340g_3.3_v_5.5_v.jpg?v=1689086403https://www.elektor.com/products/ch340-usb-to-ttl-converter-uart-module-ch340g-3-3-v-5-5-v?variant=46907068350796 in stock 7.95 1 4.9 6.9 2 - 4 Werktage 46907195490636 Circuit Simulation with TINA Design Suite & TINACloud (E-book) incl. One-year License of TINACloud Basic Edition Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907195490636-has-digital-downloads 978-3-89576-472-1 TINA Design Suite is a professional, powerful and affordable circuit simulator. It is a circuit designer and PCB design software package for analysing, designing, and real-time testing of analogue, digital, IBIS, VHDL, Verilog, Verilog AMS, SystemC, MCU, and mixed electronic circuits and their PCB layouts. In this book, top-selling Elektor author, Prof. Dr. Dogan Ibrahim aims to teach the design and analysis of electrical and electronic circuits and develop PCB boards using both TINA and TINACloud. The book is aimed at electrical/electronic engineers, undergraduate electronic/electrical engineering students at technical colleges and universities, postgraduate and research students, teachers, and hobbyists. Many tested and working simulation examples are provided covering most fields of analogue and digital electrical/electronic engineering. These include AC and DC circuits, diodes, zener diodes, transistor circuits, operational amplifiers, ladder diagrams, 3-phase circuits, mutual inductance, rectifier circuits, oscillators, active and passive filter circuits, digital logic, VHDL, MCUs, switch-mode power supplies, PCB design, Fourier series, and spectrum. Readers do not need to have any programming experience unless they wish to simulate complex MCU circuits. Limited Time Offer:Including one-year license of TINACloud Basic Edition (valued at €29) This book comes with a free licence of TINACloud Basic Edition (valued at €29) for 1 years including all example files in this book. Your personal license code will be automatically sent to you in a separate email immediately after successful payment. TINACloud is a powerful, cloud-based multi-language online circuit simulator tool that runs in your browser without any installation. TINACloud allows you to analyze & design analog, digital, VHDL, Verilog, Verilog A & AMS, MCU, and mixed electronic circuits including also SMPS, RF, communication, and optoelectronic circuits and test microcontroller applications in a mixed circuit environment. https://www.elektor.com/cdn/shop/files/circuit-simulation-with-tina-design-suite-and-tinacloud-pdf.png?v=1689089920https://www.elektor.com/products/circuit-simulation-with-tina-design-suite-tinacloud-e-book?variant=46907195490636 in stock 39.95 0 4.9 6.9 2 - 4 Werktage 46907195130188 Circuit Simulation with TINA Design Suite & TINACloud (incl. One-year License of TINACloud Basic Edition) Elektor Publishing Books Bestsellers > Books > Books | Electronics > Microcontrollers > Print Books > Programming Elektor Print Book 9783895764714 TINA Design Suite is a professional, powerful and affordable circuit simulator. It is a circuit designer and PCB design software package for analysing, designing, and real-time testing of analogue, digital, IBIS, VHDL, Verilog, Verilog AMS, SystemC, MCU, and mixed electronic circuits and their PCB layouts. In this book, top-selling Elektor author, Prof. Dr. Dogan Ibrahim aims to teach the design and analysis of electrical and electronic circuits and develop PCB boards using both TINA and TINACloud. The book is aimed at electrical/electronic engineers, undergraduate electronic/electrical engineering students at technical colleges and universities, postgraduate and research students, teachers, and hobbyists. Many tested and working simulation examples are provided covering most fields of analogue and digital electrical/electronic engineering. These include AC and DC circuits, diodes, zener diodes, transistor circuits, operational amplifiers, ladder diagrams, 3-phase circuits, mutual inductance, rectifier circuits, oscillators, active and passive filter circuits, digital logic, VHDL, MCUs, switch-mode power supplies, PCB design, Fourier series, and spectrum. Readers do not need to have any programming experience unless they wish to simulate complex MCU circuits. Limited Time Offer:Including one-year license of TINACloud Basic Edition (valued at €29) This book comes with a free licence of TINACloud Basic Edition (valued at €29) for 1 years including all example files in this book. Your personal license code will be automatically sent to you in a separate email immediately after successful payment. TINACloud is a powerful, cloud-based multi-language online circuit simulator tool that runs in your browser without any installation. TINACloud allows you to analyze & design analog, digital, VHDL, Verilog, Verilog A & AMS, MCU, and mixed electronic circuits including also SMPS, RF, communication, and optoelectronic circuits and test microcontroller applications in a mixed circuit environment. https://www.elektor.com/cdn/shop/files/circuit-simulation-with-tina-design-suite-and-tinacloud.png?v=1689089914https://www.elektor.com/products/circuit-simulation-with-tina-design-suite-tinacloud?variant=46907195130188 in stock 49.95 86 4.9 6.9 2 - 4 Werktage 46907253522764 CircuitMess Chatter - DIY LoRa Communicator CircuitMess Trade 3859893644283 Build & code your own LoRa communication device Chatter is a DIY encrypted wireless communicator. It is a free, private, security-first texting device that teaches about electronics and coding. It comes in a pair because texting yourself is not as fun as you think. Chatter uses low-power 'LoRa' wide area network technology to send text messages, emojis, memes and GIFs. DIY walkie talkie with peculiar superpowers Chatter uses long-range, low power communication (LoRa), which encodes information similar to the way dolphins and bats communicate! Comes in a pair but keeps all of your secrets Ready to become James to your Bond? Use your own private network to scramble text into a secret code that only other Chatter devices will see. Sending texts for free has never been cooler! Pairing is caring Create a whole network of friends to share your secrets with. Create avatars, customize chat features, play games, or send personalized texts, because texting yourself is not as fun as you think. Easy to follow instructions Anatomy guide: Learn about parts that make Chatter work Build guide: Step-by-step guide with 100+ photos Usage guide: Tips & tricks on how to use Chatter Coding guide: Beginner-friendly with detailed instructions Included Main circuit board Antenna Display board Button caps Acryllic casing Battery holders with batteries Pushbuttons Piezo buzzer Brass standoffs On-Off switches Metal bolts https://www.elektor.com/cdn/shop/files/circuitmess-chatter-diy-lora-communication-device.jpg?v=1698678633https://www.elektor.com/cdn/shop/files/circuitmess-chatter-diy-lora-communication-device_sending.jpg?v=1698678633,https://www.elektor.com/cdn/shop/files/circuitmess-chatter-diy-lora-communication-device_build.jpg?v=1698678633,https://www.elektor.com/cdn/shop/files/circuitmess-chatter-diy-lora-communication-device_contents.jpg?v=1698678633https://www.elektor.com/products/circuitmess-chatter-diy-lora-communicator?variant=46907253522764 out of stock 169.95 0 0 0 nicht auf Lager 46907164197196 CircuitMess Nibble - DIY Game Console CircuitMess Trade Bestsellers > Components > Fun Electronics > Kits > Platforms 3859893644368 Features Processor: 32-bit, 160MHz Storage: 4 MB RAM: 80 KB Display: 1.4″ 128 x 128 Full-color TFT Connectivity: WiFi Build time: 2 hours Programming: C++ (Arduino), CircuitBlocks, Python Parts Main circuit board Acrylic casing Metal soldering iron stand Sponge Soldering iron Solder wire Cross screwdriver AAA alkaline batteries LCD display Micro USB cable Bag with small components Battery holder Here you can find the guide to assemble your CircuitMess Nibble – DIY Game Console. https://www.elektor.com/cdn/shop/files/circuitmess_nibble_diy_game_console_-_overview.jpg?v=1698678644https://www.elektor.com/cdn/shop/files/circuitmess_nibble_diy_game_console_-_package.jpg?v=1698678644,https://www.elektor.com/cdn/shop/files/circuitmess-nibble-diy-game-console_front.jpg?v=1698678644,https://www.elektor.com/cdn/shop/files/circuitmess-nibble-diy-game-console_parts.jpg?v=1698678644,https://www.elektor.com/cdn/shop/files/circuitmess-nibble-diy-game-console_package.jpg?v=1698678644https://www.elektor.com/products/circuitmess-nibble-diy-game-console?variant=46907164197196 in stock 84.95 5 0 6.9 2 - 4 Werktage 46907164229964 CircuitMess Spencer - DIY Voice Assistant CircuitMess Trade Bestsellers > Components > Fun Electronics > Kits > No Member Discount > Platforms > Sale 3859893644153 Features Ask about the weather forecast for your area Hear a joke Ask him to sing you a song Set a stopwatch Make Spencer display custom animations Laugh at his corny popular culture references Included Spencer’s circuit board that includes a pre-soldered 144-pixel LED grid The brain board – does smart stuff and includes a dual-core processor, a 16 MB flash memory chip, and power-management circuitry Acrylic casing – this protects Spencer’s innards from the outside world A big red button Various smaller components such as resistors and pushbuttons Micro USB cable for powering your Spencer 5W Speaker Instruction booklet – ready for your offline knowledge consumption Here you can find the assembly guide! https://www.elektor.com/cdn/shop/files/circuitmess_spencer_diy_voice_assistant.jpg?v=1698678650https://www.elektor.com/cdn/shop/files/circuitmess-spencer-diy-voice-assistant_back.jpg?v=1698678650,https://www.elektor.com/cdn/shop/files/circuitmess-spencer-diy-voice-assistant_parts.jpg?v=1698678650,https://www.elektor.com/cdn/shop/files/circuitmess-spencer-diy-voice-assistant_package.jpg?v=1698678650https://www.elektor.com/products/circuitmess-spencer-diy-voice-assistant?variant=46907164229964 in stock 99.95 59.95 12 0 6.9 2 - 4 Werktage 46907070677324 Cleaning Nozzle Drill Kit (0.1-1.0 mm) Elektor Trade Bestsellers > Hand Tools > Measuring Tools > Prototyping A119-00331354327A Cleaning nozzle drill kit small box containing 10 carbide PCB drills from 0.1 mm to 1 mm all with 4 mm shaft. Ideal for drilling small precision holes in pcb's, plastic or soft metal. https://www.elektor.com/cdn/shop/files/cleaning_nozzle_drill_kit_0.1-1.jpg?v=1689086455https://www.elektor.com/products/cleaning-nozzle-drill-kit-0-1-1-0-mm?variant=46907070677324 in stock 8.95 12 4.9 6.9 2 - 4 Werktage 46907246444876 Clearpath Robotics TurtleBot 4 Lite Elektor Trade Bestsellers > Education > No Member Discount > Platforms > Raspberry Pi > Raspberry Pi Kits > Robotics 0096718607815 TurtleBot 4 is the next-generation of the world’s most popular open source robotics platform for education and research, offering better computing power, better sensors and a world class user experience at an affordable price point.TurtleBot 4 Lite is equipped with an iRobot Create 3 mobile base, a powerful Raspberry Pi 4 running ROS 2, OAK-D spatial AI stereo camera, 2D LiDAR and more. All components have been seamlessly integrated to deliver an out-of-the-box development and learning platform.SpecificationsBase platformiRobot Create 3Wheels (Diameter)72 mmGround Clearance4.5 mmOn-board ComputerRaspberry Pi 4 (4 GB)Maximum linear velocity0.31 m/s in safe mode0.46 m/s without safe modeMaximum angular velocity1.90 rad/sMaximum payload9 kgOperation time2h 30m – 4h depending on loadCharging time2h 30mLidarRPLIDAR A1M8CameraOAK-D-LiteUser PowerVBAT @1.9 A5 V @ Low current3.3 V @ Low currentUSB Expansion2x USB 2.0 (Type A)2x USB 3.0 (Type A)Programmable LEDsCreate 3 LightringButtons and Switches2x Create 3 User buttons1x Create 3 Power ButtonBattery26 Wh Lithium Ion (14.4 V nominal)Charging DockIncludedSize (L x W x H)342 x 339 x 192 mmWeight3.3 kgDownloadsUser Manual https://www.elektor.com/cdn/shop/files/clearpath-robotics-turtlebot-4-lite.jpg?v=1689091876https://www.elektor.com/cdn/shop/files/clearpath-robotics-turtlebot-4-lite_sides.jpg?v=1696854325,https://www.elektor.com/cdn/shop/files/clearpath-robotics-turtlebot-4-lite_lidar.jpg?v=1696854325,https://www.elektor.com/cdn/shop/files/clearpath-robotics-turtlebot-4-lite_camera.jpg?v=1698678663https://www.elektor.com/products/clearpath-robotics-turtlebot-4-lite?variant=46907246444876 in stock 1599.0 0 0 0 2 - 4 Werktage 46906937999692 Computer Vision (EN) | E-book Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906937999692-has-digital-downloads 978-0-905705-71-2 Computer vision is probably the most exciting branch of image processing, and the number of applications in robotics, automation technology and quality control is constantly increasing. Unfortunately entering this research area is, as yet, not simple. Those who are interested must first go through a lot of books, publications and software libraries. With this book, however, the first step is easy. The theoretically founded content is understandable and is supplemented by many practical examples. Source code is provided with the specially developed platform-independent open source library IVT in the programming language C/C++. The use of the IVT is not necessary, but it does make for a much easier entry and allows first developments to be quickly produced. The authorship is made up of research assistants of the chair of Professor Ruediger Dillmann at the Institut für Technische Informatik (ITEC), Universitaet Karlsruhe (TH). Having gained extensive experience in image processing in many research and industrial projects, they are now passing this knowledge on. Among other subjects, the following are dealt with in the fundamentals section of the book: Lighting, optics, camera technology, transfer standards, camera calibration, image enhancement, segmentation, filters, correlation and stereo vision. The practical section provides the efficient implementation of the algorithms, followed by many interesting applications such as interior surveillance, bar code scanning, object recognition, 3-D scanning, 3-D tracking, a stereo camera system and much more. https://www.elektor.com/cdn/shop/files/elektor-computer-vision-ebook.jpg?v=1689083566https://www.elektor.com/cdn/shop/files/computer-vision_3.jpg?v=1696848554https://www.elektor.com/products/computer-vision-ebook-en?variant=46906937999692 in stock 16.95 0 4.9 6.9 2 - 4 Werktage 46907254538572 Connex SMPS800RE Switched-mode Power Supply (230 V, ±40 V) Elektor Trade Bestsellers > Deals > No Member Discount > Power Supplies 020410 The SMPS800RE Switched-mode Power Supply (SMPS) has a differential output voltage and two separate regulated auxiliary voltages. It is specially designed to be used with both Single-Ended and BTL output class AB, H, D or T Audio Amplifiers. SMPS800RE use state of the art, High efficiency LLC Series Resonant ConverterTopology. Due to the soft-switched topology used, the SMPS800RE has very low EMI noise, lower losses and is more compact than a similar power rating classic hard-switched SMPS. Features LLC Series Resonant Converter Topology for high efficiency, up to 95.2% and lowest EMI 230 V AC (200-250 V) AC compatible 800 W Continuous Output Power with cooling, 1000 W Peak Output Power, 1150 W Short-Time Peak Power Complete protection set, Under-voltage, Over-voltage, Over-current, and Over-temperature Protection Burst-Mode operation at low load or no-load for high efficiency with under 3 W consumption On-board Soft Start for smooth turns ON without current peaks or breaker tripping On-board variable speed fan controller and optional cooling fan, over-temperature shut-down IEC type Connector for Mains Input voltage and terminal block for Voltage Output, LED light for power ON Specifications Mains Voltage 230 V Output Voltage ±40 V Aux Output Voltage ±12 V Output Power 800 W Cooling Fan No Dimensions 150 x 100 x 42 mm Weight 0.78 kg Downloads Datasheet https://www.elektor.com/cdn/shop/files/connex-smps800re-switched-mode-power-supply.jpg?v=1689092156https://www.elektor.com/products/connex-smps800re-switched-mode-power-supply-230-v-40-v?variant=46907254538572 in stock 179.95 154.95 14 0 0 2 - 4 Werktage 46907121107276 Content Marketing, Engineered Elektor Trade Basics > Bestsellers > Books > No Member Discount > Sale 9781632992857 Build Trust and Convert Buyers with Technical ContentResearch shows that this analytical, skeptical buyer conducts a great deal of independent research before engaging with vendors. Companies that share expertise through high-quality content on a consistent basis are not only seen as trusted resources, they also spend less per lead and achieve greater pipeline efficiency.Content Marketing, Engineered guides you through the key steps in creating content to inform, educate, and help your technical buyers on their journey to purchase and beyond. By the time you reach the last page, you’ll be familiar with the entire end-to-end content marketing process, from planning and writing to publishing, promoting, and measuring the performance of your content. https://www.elektor.com/cdn/shop/files/content_marketing_engineered.png?v=1689087858https://www.elektor.com/products/content-marketing-engineered?variant=46907121107276 in stock 12.95 9.95 4 4.9 6.9 2 - 4 Werktage 46907093844300 Control Your Home with Raspberry Pi Elektor Publishing Books Bestsellers > Books > Books | IoT & Automation > Print Books > Raspberry Pi > Raspberry Pi Books > Raspberry Pi | Arduino | ESP Elektor Print Book 9781907920943 Secure, Modular, Open-Source and Self-SufficientEver since the Raspberry Pi was introduced, it has been used by enthusiasts to automate their homes. The Raspberry Pi is a powerful computer in a small package, with lots of interfacing options to control various devices. This book shows you how you can automate your home with a Raspberry Pi. You’ll learn how to use various wireless protocols for home automation, such as Bluetooth, 433.92 MHz radio waves, Z-Wave, and Zigbee. Soon you’ll automate your home with Python, Node-RED, and Home Assistant, and you’ll even be able to speak to your home automation system. All this is done securely, with a modular system, completely open-source, without relying on third-party services. You’re in control of your home, and no one else.At the end of this book, you can install and configure your Raspberry Pi as a highly flexible home automation gateway for protocols of your choice, and link various services with MQTT to make it your own system. This DIY (do it yourself) approach is a bit more laborious than just installing an off-the-shelf home automation system, but in the process, you can learn a lot, and in the end, you know exactly what’s running your house and how to tweak it. This is why you were interested in the Raspberry Pi in the first place, right?Turn your Raspberry Pi into a reliable gateway for various home automation protocols.Make your home automation setup reproducible with Docker Compose.Secure all your network communication with TLS.Create a video surveillance system for your home.Automate your home with Python, Node-RED, Home Assistant and AppDaemon.Securely access your home automation dashboard from remote locations.Use fully offline voice commands in your own language.DownloadsErrata on GitHub https://www.elektor.com/cdn/shop/files/control-your-home-with-raspberry-pi.png?v=1689087371https://www.elektor.com/products/control-your-home-with-raspberry-pi?variant=46907093844300 in stock 37.5 45 4.9 6.9 2 - 4 Werktage 46907091648844 Control Your Home with Raspberry Pi (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46907091648844-has-digital-downloads Secure, Modular, Open-Source and Self-SufficientEver since the Raspberry Pi was introduced, it has been used by enthusiasts to automate their homes. The Raspberry Pi is a powerful computer in a small package, with lots of interfacing options to control various devices. This book shows you how you can automate your home with a Raspberry Pi. You’ll learn how to use various wireless protocols for home automation, such as Bluetooth, 433.92 MHz radio waves, Z-Wave, and Zigbee. Soon you’ll automate your home with Python, Node-RED, and Home Assistant, and you’ll even be able to speak to your home automation system. All this is done securely, with a modular system, completely open-source, without relying on third-party services. You’re in control of your home, and no one else.At the end of this book, you can install and configure your Raspberry Pi as a highly flexible home automation gateway for protocols of your choice, and link various services with MQTT to make it your own system. This DIY (do it yourself) approach is a bit more laborious than just installing an off-the-shelf home automation system, but in the process, you can learn a lot, and in the end, you know exactly what’s running your house and how to tweak it. This is why you were interested in the Raspberry Pi in the first place, right?Turn your Raspberry Pi into a reliable gateway for various home automation protocols.Make your home automation setup reproducible with Docker Compose.Secure all your network communication with TLS.Create a video surveillance system for your home.Automate your home with Python, Node-RED, Home Assistant and AppDaemon.Securely access your home automation dashboard from remote locations.Use fully offline voice commands in your own language.Download the software and view the errata for the book on GitHub. https://www.elektor.com/cdn/shop/files/control-your-home-with-raspberry-pi-pdf_1.png?v=1689087364https://www.elektor.com/products/control-your-home-with-raspberry-pi-e-book?variant=46907091648844 in stock 32.5 0 4.9 6.9 2 - 4 Werktage 46906979713356 Controller Area Network Projects (E-BOOK) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906979713356-has-digital-downloads The Controller Area Network (CAN) was originally developed to be used as a vehicle data bus system in passenger cars. Today, CAN controllers are available from over 20 manufacturers, and CAN is finding applications in other fields, such as medical, aerospace, process control, automation, and so on. This e-book (pdf) is written for students, for practising engineers, for hobbyists, and for everyone else who may be interested to learn more about the CAN bus and its applications. The aim of this e-book is to teach you the basic principles of CAN networks and in addition the development of microcontroller based projects using the CAN bus. In summary, this e-book enables the reader to: Learn the theory of the CAN bus used in automotive industry Learn the principles, operation, and programming of microcontrollers Design complete microcontroller based projects using the C language Develop complete real CAN bus projects using microcontrollers Learn the principles of OBD systems used to debug vehicle electronics You will learn how to design microcontroller based CAN bus nodes, build a CAN bus, develop high-level programs, and then exchange data in real-time over the bus. You will also learn how to build microcontroller hardware and interface it to LEDs, LCDs, and A/D converters. The e-book assumes that the reader has some knowledge on basic electronics. Knowledge of the C programming language will be useful in later chapters of the e-book, and familiarity with at least one member of the PIC series of microcontrollers will be an advantage, especially if the reader intends to develop microcontroller based projects using the CAN bus. https://www.elektor.com/cdn/shop/files/controller-area-network-projects_ebook.jpg?v=1689084600https://www.elektor.com/products/controller-area-network-projects-e-book?variant=46906979713356 in stock 24.95 0 4.9 6.9 2 - 4 Werktage 46906964934988 Controller Area Network Projects with ARM and Arduino Elektor Publishing Books Arduino > Arduino Books > Bestsellers > Books > Microcontrollers > Print Books Elektor Print Book 9781907920509 This book details the use of the ARM Cortex-M family of processors and the Arduino Uno in practical CAN bus based projects. Inside, it gives a detailed introduction to the architecture of the Cortex-M family whilst providing examples of popular hardware and software development kits. Using these kits helps to simplify the embedded design cycle considerably and makes it easier to develop, debug, and test a CAN bus based project. The architecture of the highly popular ARM Cortex-M processor STM32F407VGT6 is described at a high level by considering its various modules. In addition, the use of the mikroC Pro for ARM and Arduino Uno CAN bus library of functions are described in detail. This book is written for students, for practising engineers, for hobbyists, and for everyone else who may need to learn more about the CAN bus and its applications. The book assumes that the reader has some knowledge of basic electronics. Knowledge of the C programming language will be useful in later chapters of the book, and familiarity with at least one microcontroller will be an advantage, especially if the reader intends to develop microcontroller based projects using CAN bus. The book should be useful source of reference to anyone interested in finding an answer to one or more of the following questions: What bus systems are available for the automotive industry? What are the principles of the CAN bus? What types of frames (or data packets) are available in a CAN bus system? How can errors be detected in a CAN bus system and how reliable is a CAN bus system? What types of CAN bus controllers are there? What are the advantages of the ARM Cortex-M microcontrollers? How can one create a CAN bus project using an ARM microcontroller? How can one create a CAN bus project using an Arduino microcontroller? How can one monitor data on the CAN bus? https://www.elektor.com/cdn/shop/files/controller-area-network-projects-with-arm-and-arduino.png?v=1689084121https://www.elektor.com/products/controller-area-network-projects-with-arm-and-arduino?variant=46906964934988 in stock 37.5 51 4.9 6.9 2 - 4 Werktage 46906977550668 Controller Area Network Projects with ARM and Arduino (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906977550668-has-digital-downloads This book details the use of the ARM Cortex-M family of processors and the Arduino Uno in practical CAN bus based projects. Inside, it gives a detailed introduction to the architecture of the Cortex-M family whilst providing examples of popular hardware and software development kits. Using these kits helps to simplify the embedded design cycle considerably and makes it easier to develop, debug, and test a CAN bus based project. The architecture of the highly popular ARM Cortex-M processor STM32F407VGT6 is described at a high level by considering its various modules. In addition, the use of the mikroC Pro for ARM and Arduino Uno CAN bus library of functions are described in detail. This book is written for students, for practising engineers, for hobbyists, and for everyone else who may need to learn more about the CAN bus and its applications. The book assumes that the reader has some knowledge of basic electronics. Knowledge of the C programming language will be useful in later chapters of the book, and familiarity with at least one microcontroller will be an advantage, especially if the reader intends to develop microcontroller based projects using CAN bus. The book should be useful source of reference to anyone interested in finding an answer to one or more of the following questions: What bus systems are available for the automotive industry? What are the principles of the CAN bus? What types of frames (or data packets) are available in a CAN bus system? How can errors be detected in a CAN bus system and how reliable is a CAN bus system? What types of CAN bus controllers are there? What are the advantages of the ARM Cortex-M microcontrollers? How can one create a CAN bus project using an ARM microcontroller? How can one create a CAN bus project using an Arduino microcontroller? How can one monitor data on the CAN bus? https://www.elektor.com/cdn/shop/files/controller-area-network-projects-with-arm-and-arduino-pdf.png?v=1689084536https://www.elektor.com/products/controller-area-network-projects-with-arm-and-arduino-e-book?variant=46906977550668 in stock 27.95 -1 4.9 6.9 2 - 4 Werktage 46907210727756 Creality Ender-3 S1 3D Printer Creality Trade 3D Printers > Bestsellers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > Production & Repair Comparison Websites 6971636401346 Features 96% pre-installed 6-step fast assembly Silent Motherboard, Decibel ≤50 dB Resumed Printing, Save Time and Filament Take out the Model in an Easier Way New UI Interaction with LCD Knob Screen 4.3-inch HD Color Screen Specifications Modeling technology FDM (Fused Deposition Modeling) Printer size 487 x 453 x 622 mm Build size 220 x 220 x 270 mm Supported filament PLA/TPU/PETG/ABS Printing layer thickness 0.05-0.35 mm Printing speed 150 mm/s at the maximum Printing precision ±0.1 mm Nozzle diameter 0.4 mm Number of nozzles 1 Filament diameter 1.75 mm Machine net weight 9.1 kg EXtruder gear ratio 1:3.5 Automatic bed leveling CR touch Printing platform PC spring steel sheet Screen Knob color screen Rated voltage 115/230 V | 50/60 Hz | 4.5/2.5 A Printing method Type-C USB /SD card Supported file format STL/OBJ/AMF Supported software Slicer/Cura/Repetier-Host/Simplify3D Downloads Quick Installation Guide Firmware Z-axis Limit Firmware https://www.elektor.com/cdn/shop/files/creality-ender-3-s1-3d-printer.jpg?v=1689090569https://www.elektor.com/cdn/shop/files/creality-ender-3-s1-3d-printer_view.jpg?v=1696853397,https://www.elektor.com/cdn/shop/files/creality-ender-3-s1-3d-printer_side.jpg?v=1696853397https://www.elektor.com/products/creality-ender-3-s1-3d-printer?variant=46907210727756 in stock 439.0 2 0 0 2 - 4 Werktage 46907220656460 Creality HALOT-LITE CL-89L Resin 3D Printer Creality Trade 3D Printers > Bestsellers > Measuring Tools > No Member Discount > Production & Repair > Sale 020139 Integral Light Source, High Precision and Uniformity The self-developed integral light source adopts the reflection & refraction to make the light intensity distribution of the whole screen uniform, and each dimension of the model with consistent accuracy. Integral Light Source vs Matrix Light Source Integral light source: It is composed of 12 lamp beads, and each lamp bead e is composed of 4 light-emitting chips, the uniformity of light source energy can reach more than 80%. When the individual lamp beads are attenuated, the uniformity of the printed model e is not affected. Ordinary light source: It consists of many ultraviolet lamp beads evenly arranged in a row. The light intensity of the lamp bead splicing area is uneven, and the lamp bead damage has a greater impact on the uniformity of the printed model. Wi-Fi/APP Remote Control Creality Cloud APP for monitor printing progress, adjust the printing settings, Start/Stop prints. Built-in Wi-Fi allows one-click upgrades to the firmware. Double Heat Dissipation, Efficient Purification Specially designed dual heat dissipation system, precise and intelligent control to detect the heat source, and quickly evaporate heat. Activated carbon air filtration system to reduce odor emission and optimize printing experience. Specifications LCD pixel 3840 x 2400 LCD screen 8.9' monochrome Light source Integral Light Source Printing size 192 x 120 x 200 mm XY-axis precision 0.05 mm Printing speed 1-4s/layer Layer thickness 0.01-0.2 mm Interaction screen 5' color touch screen Material 405 nm UV Resin Auto-leveling Easy manual leveling Input power 100-240 V Machine size 330 x 301 x 572 mm Machine weight 10.6 kg https://www.elektor.com/cdn/shop/files/creality-halot-lite-cl-89l-resin-3d-printer.jpg?v=1689090742https://www.elektor.com/cdn/shop/files/creality-halot-lite-cl-89l-resin-3d-printer_right.jpg?v=1696853548,https://www.elektor.com/cdn/shop/files/creality-halot-lite-cl-89l-resin-3d-printer_left.jpg?v=1696853548,https://www.elektor.com/cdn/shop/files/creality-halot-lite-cl-89l-resin-3d-printer_front.jpg?v=1696853548https://www.elektor.com/products/creality-halot-lite-cl-89l-resin-3d-printer?variant=46907220656460 in stock 649.0 549.0 5 0 0 2 - 4 Werktage 46907211415884 Creality HALOT-ONE CL-60 Resin 3D Printer Creality Trade 3D Printers > Comparison Websites DE > Comparison Websites FR > Measuring Tools > No Member Discount > Production & Repair > Sale Comparison Websites 020110 Features NEW Light Source Structure120W Power Super spotlight. The self-developed integral light source, Precision light control High agility slicing, Creality New Slicing SystemA Simplified user interface and Easy Modeling function, and supports the parameter customizedHigh-stability Z-axis for high-quality printing. WIFI-APP intelligent control. Supports Creality Cloud. OTA online upgradeNew Firmware/new system. One-click upgrade. Get better experience in firmware upgrade Smart Operation System Linux64-bit 4-core CPU+GPU Mainboard supports the faster operation and greatly improves printing efficiency. Great Operation ExperienceLinux System For a better AI Experience, a 5-inch high definition colorful touch screen keep easy works. Specifications Build Size 127 x 80 x 160 mm XY Axis Resolution 1620 x 2560 Print Speed 1-4s/layer Layer Thickness L0.01-0.2 mm Touch Screen 5 inch touch screen Light Source Type Integral Light Source (wavelength 405 nm) Rated Voltage 100-240 VAC 50/60Hz Print Method USB Disk, Creality Cloud, HALOT BOX WiFi Machine Language 14 languages (English, French, German, Spanish, Portuguese, Japanese, Korean, Turkish, Italian, Russian, Dutch, Polish, Simplified Chinese, Traditional Chinese) Compatible Resin Common rigid photosensitive, Standard resin, High hardness, High toughness, Dental model resin Gross Weight 8.8 kg Package Size 295 x 295 x 545 mm Net Weight 7.1 kg Rated Power 100 W Machine Size 221 x 221 x 404 mm Downloads Manual & Firmware https://www.elektor.com/cdn/shop/files/creality-halot-one-cl-60-resin-3d-printer.jpg?v=1689090576https://www.elektor.com/cdn/shop/files/creality-halot-one-cl-60-resin-3d-printer_left.jpg?v=1696853407,https://www.elektor.com/cdn/shop/files/creality-halot-one-cl-60-resin-3d-printer_right.jpg?v=1696853407,https://www.elektor.com/cdn/shop/files/creality-halot-one-cl-60-resin-3d-printer_internal.jpg?v=1696853408,https://www.elektor.com/cdn/shop/files/creality-halot-one-cl-60-resin-3d-printer_features.jpg?v=1696853408https://www.elektor.com/products/creality-halot-one-cl-60-resin-3d-printer?variant=46907211415884 out of stock 279.0 229.0 0 0 0 nicht auf Lager 47571247923532 CrowBot BOLT - Programmable Smart Robot Car Kit (with Joystick) Elecrow Trade Bestsellers > Components > Fun Electronics > Kits > NEW > Platforms > Robotics 020709 CrowBot BOLT is an ESP32-controlled, intelligent, simple and easy-to-use open source robot car. It is compatible with the Arduino and MicroPython environments, with graphical programming via Letscode. 16 learning courses with interesting experiments are available. Features 16 lessons in three languages (Letscode, Arduino, Micropython), fast learning and fun experiments Compatible with Arduino, MicroPython development environment, using Letscode graphical programming, easy to use Strong scalability, with a variety of interfaces, can be expanded and used with Crowtail modules A variety of remote control modes, you can use the infrared remote control and joystick to control the car Specifications Processor ESP32-Wrover-B (8 MB) Programming Letscode, Arduino, Micropython Control method Bluetooth Remote Control/Infrared Remote Control Input Button, Light sensor, Infrared Receiving Module, Ultrasonic Sensor, Line Tracking Sensor Output Buzzer, Programmable RGB Light, Motor Wifi & Bluetooth Yes Light sensor Can realize the function of chasing light or avoiding light Ultrasonic Sensor When an obstacle is detected, the driving route of the car can be corrected to avoid the obstacle Line Tracking Sensor Can make the car move along the dark/black lines, intelligently judge and correct the driving path Buzzer Can make the car sound/whistle, bringing a more direct sensory experience Programmable RGB Light Through programming, it can show colorful lights in different scenes Infrared receiver Receive infrared remote control signals to realize remote control Interfaces 1x USB-C, 1x I²C, 1x A/D Motor type GA12-N20 Micro DC Gear Motor Operating temperature -10℃~+55℃ Power supply 4x 1.5 V batteries (not included) Battery life 1.5 hours Dimensions 128 x 92 x 64 mm Weight 900 g Included 1x Chassis 1x Ultrasonic Sensor 1x Battery Holder 2x Wheels 4x M3x8 mm Screws 2x M3x5 mm Copper Column 2x Side Acrylic Plates 1x Front Acrylic Plates 1x Screwdriver 2x 4 Pin Crowtail Cable 1x USB-C Cable 1x Infrared remote control 1x Instructions & Line Track Map 1x Joystick Downloads Wiki CrowBot-BOLT_Assembly-Instruction Joystick-for-CrowBot-BOLT_Assembly-Instruction CrowBot_BOLT_Beginner’s_Guide Designing Documents of CrowBot Designing Documents of Joystick Lesson Code 3D Model Factory Source Code https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit.jpg?v=1711460308https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit_lights.jpg?v=1711460334,https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit_tracking.jpg?v=1711460385,https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit_parts.jpg?v=1711460395,https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit_joystick.jpg?v=1711460406,https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit_board.jpg?v=1711460415,https://www.elektor.com/cdn/shop/files/CrowBot-BOLT-Robot-Car-Kit_contents.jpg?v=1711460440https://www.elektor.com/products/crowbot-bolt-programmable-smart-robot-car-kit-with-joystick?variant=47571247923532 in stock 64.95 8 0 6.9 2 - 4 Werktage 47310492107084 Crowtail-4G SIM A7670E Module GPS Breakout Board Elektor Trade Bestsellers > Components > Modules > NEW 020542 This Crowtail series 4G module is a high-performance LTE Cat1 wireless module. It uses the SIM A7670E communication module from Simcom and communicates through a UART interface, which enables 4G data transmission and voice communication. The module supports multiple LTE bands, including B1/B3/B5/B7/B8/B20, as well as WCDMA and GSM networks. In addition, it supports various protocols such as TCP/IP, FTP, HTTP, and multiple satellite navigation systems such as GPS, GLONASS, and BDS. The module comes with a charging interface and can be powered by a 3.7 V lithium battery or a 5 V USB-C interface. It also has a 3.5 mm headphone jack, and by connecting a headphone with a microphone, it can be used for making and receiving phone calls. Its compact size makes it easy to integrate into various IoT devices and meet various application requirements. Furthermore, its low power consumption and reliable performance are also the reasons why it is widely used in IoT, smart home, automotive, and industrial control fields. Features Integrate the A7670E communication module, enabling 4G data transmission and voice communication with low power consumption and high reliability Supports multiple LTE bands, including B1/B3/B5/B7/B8/B20, as well as WCDMA and GSM networks Supports various protocols such as TCP/IP, FTP, HTTP, and multiple satellite navigation systems such as GPS, GLONASS, and BDS Comes with a charging interface and a headphone jack, which can be used for making and receiving phone calls by connecting a headphone with a microphone Small but powerful, compact size makes it easy to integrate into various IoT devices. Specifications Main Chip: SIM A7670E LTE-FDD: B1/B3/B5/B7/B8/B20 GSM: 900/1800 MHz GSM/GPRS power class EGSM900: 4 (33 dBm ±2 dB) DCS1800: 1 (30 dBm ±2 dB) EDGE power class: EGSM900: E2 (27 dBm ±3 dB) DCS1800 : E1 (26 dBm +3 dB/-4 dB) LTE power class: 3 (23 dBm ±7 dB) Supply Voltage: 4 V ~ 4.2 V Power: 3.8 V LTE(Mbps): 10 (DL)/5 (UL) GPRS/EDGE(Kbps): 236.8 (DL)/236.8 (UL) Protocol: TCP/IP/IPV4/IPV6/Multi-PDP/FTP/FTPS /HTTP/HTTPS/DNS Communication interface: USB / UART Firmware Upgrade: USB/FOTA Support phonebook types: SM/FD/ON/AP/SDN Interfaces: 1x Power button, 1x BAT, 1x UART, 1x USB-C, 1x SIM Card slot Dimensions: 35 x 50 mm Included 1x Crowtail-4G SIM-A7670E 1x 4G GSM NB-IoT Antenna 1x GPS ceramic antenna Downloads Wiki A7670 AT Command Manual A7670 Datasheet Source Code https://www.elektor.com/cdn/shop/files/crowtail-4g-sim-a7670e-module-gps-breakout-board.jpg?v=1699286922https://www.elektor.com/cdn/shop/files/crowtail-4g-sim-a7670e-module-gps-breakout-board_front.jpg?v=1699286922,https://www.elektor.com/cdn/shop/files/crowtail-4g-sim-a7670e-module-gps-breakout-board_back.jpg?v=1699286921,https://www.elektor.com/cdn/shop/files/crowtail-4g-sim-a7670e-module-gps-breakout-board_included.jpg?v=1699286921https://www.elektor.com/products/crowtail-4g-sim-a7670e-module-gps-breakout-board?variant=47310492107084 in stock 39.95 24 4.9 6.9 2 - 4 Werktage 47310492369228 CrowVi 13.3" IPS HD Touch Display (1920x1080) Elecrow Trade Bestsellers > Components > Displays > Displays & LEDs > NEW 020583 Nowadays, more and smarter phones and laptops adopt USB-C ports for its powerful function that can transmit power, data, and video information. USB-C solution can also make the device much thinner compared to the Thunderbolt 3 or HDMI-compatible port. That’s why we the CrowVi portable USB-C monitor was created. The super thin CrowVi 13.3' monitor has 2 USB-C ports, one is for power delivery, and the other is for data transmission of video and touch screen commands. The screen also can be connected through the mini HDMI-compatible port. The resolution of CrowVi is 1920x1080, which will provide a better experience for gaming and watching movies. Features CrowVi shell is made of aluminum alloy, its thickness is as thin as 5 mm, and the screen border is as narrow as 6 mm. The whole monitor looks exquisite and elegant. CrowVi can not only act as the dual monitor for smartphones, and laptops but also as the single monitor for gaming devices and some computer mainframes like Mac mini, Raspberry Pi, etc. CrowVi brings you a much larger view compared to the phone. It enables better experiences for gaming and watching movies. Specifications Screen 13.3' TFT IPS LCD Screen Size 294.5 x 164 mm Thickness 5-10 mm Resolution 1920 x 1080 Brightness 300 nits Refresh Rate 60 Hz Color Gamut 16.7M, NTSC 72%, sRGB up to 100% Contrast 800:1 Backlight LED Viewing Angle 178° Aspect Ratio 16:9 Speaker Dual speakers 8 Ω, 2 W Shell Aluminum alloy Input Mini-HD, Type-C, PD Output 3.5 mm headphone jack Power PD 5-20 V or USB-C 3.0 Operating Temperature 0-50°C Dimensions 313 x 198 x 10 mm Weight (Smart Case) 350 g Weight (Monitor) 700 g Included 13.3-inch Touch screen monitor Smart case USB-C to USB-C cable (1 m) USB-A to USB-C power cable (1 m) HDMI to mini-HDMI cable (1 m) Power adapter (5 V/2 A) HDMI to mini-HDMI adapter Dust cloth User manual Downloads User manual https://www.elektor.com/cdn/shop/files/crowvi-13-inch-ips-hd-touch-display-1920x1080.jpg?v=1699287126https://www.elektor.com/cdn/shop/files/crowvi-13-inch-ips-hd-touch-display-1920x1080_stand.jpg?v=1699287126,https://www.elektor.com/cdn/shop/files/crowvi-13-inch-ips-hd-touch-display-1920x1080_smartphone.jpg?v=1699287126,https://www.elektor.com/cdn/shop/files/crowvi-13-inch-ips-hd-touch-display-1920x1080_mirroring.jpg?v=1699287126,https://www.elektor.com/cdn/shop/files/crowvi-13-inch-ips-hd-touch-display-1920x1080_rpi.jpg?v=1699287126,https://www.elektor.com/cdn/shop/files/crowvi-13-inch-ips-hd-touch-display-1920x1080_included.jpg?v=1699287126https://www.elektor.com/products/crowvi-13-inch-ips-hd-touch-display-1920x1080?variant=47310492369228 in stock 199.95 9 0 0 2 - 4 Werktage 47754489561420 CrowVision 11.6" IPS Capacitive Touch Display (1366x768) Elecrow Trade Bestsellers > Components > Displays > Displays & LEDs > NEW > Raspberry Pi > Raspberry Pi Displays 020792 CrowVision 11.6-inch touch screen is designed for all-in-one machines. It features a 1366 x 768 high-resolution screen and IPS panel, providing a superior visual experience. The industrial design-style rear-fixed metal structure is compatible with various single-board computers (SBCs), with a reasonable layout and neat wiring, making it easy to power up and use with simple operations.The screen uses HDMI-compatible communication and supports capacitive multi-touch. It has reserved interfaces and buttons for speakers and other accessories, making it adaptable to different usage scenarios. It can be used with a variety of commonly available single-board computers such as Raspberry Pi, Jetson Nano, and is plug-and-play, while also being fully compatible with the operating systems of single-board computers (such as Raspbian, Ubuntu, Windows, Android, Mac OS, and Chrome OS, etc.).This screen can be widely used in automation application control system displays, personal DIY projects, secondary screen/second window displays, single-board computer audio-video display equipment, HDMI communication devices, game console expansion screens, and other scenarios.Features11.6-inch high-resolution screen with 1366 x 768 resolution, IPS panel, and 178° wide viewing angle provides a better visual experienceUnique rear fixing structure with sliding fixing pillars, compatible with most single-board computer models, easy to assembleWide compatibility, compatible with multiple operating systems (Raspbian, Ubuntu, Windows, Android, Mac OS, and Chrome OS)Supports audio, video, and capacitive touch, plug and playIntegrates a variety of peripheral interfaces (such as speakers, headphones, keypads, touchscreens) and onboard OSD adjustment keysThe mainboard is equipped with power conversion function of output 5 V/3 A, not need to separately connect an external power supply for the single-board computer.SpecificationsDisplay size: 11.6 inchTouch type: 5-point Capacitive TouchResolution: 1366 x 768Color depth: 16MViewing angle: 178° wide viewing angleDisplay type: IPS PanelScreen type: TFT-LCDExternal power supply: 12 V/2 ADigital input: HDMI-compatible interfaceInterfaces: 1x Keypad interface, 1x power supply 5 V output, 1x Mini HD interface, 1x touch interface, 1x speaker interface, 1x headphone socket, 1x power supply 12 V inputCompatibility system: Raspbian, Ubuntu, Windows, Android, Mac OS, and Chrome OS, etc.Active Area: 256.13 x 144 mmDimensions: 290.8 x 184.2 mmIncluded1x 11.6-inch capacitive touch ccreen1x USB-A to USB-C cable1x USB-A to micro B cable1x HD to mini HD cable1x Micro HD to mini HD cable1x OSD control board1x Power adapter1x Screwdriver2x Ribbon1x ManualDownloadsManualWiki https://www.elektor.com/cdn/shop/files/CrowVision-11.6-inch-IPS-Capacitive-Touch-Display-1366x768.jpg?v=1712561065https://www.elektor.com/cdn/shop/files/CrowVision-11.6-inch-IPS-Capacitive-Touch-Display-1366x768_features.jpg?v=1712561113,https://www.elektor.com/cdn/shop/files/CrowVision-11.6-inch-IPS-Capacitive-Touch-Display-1366x768_sbc.jpg?v=1712561189,https://www.elektor.com/cdn/shop/files/CrowVision-11.6-inch-IPS-Capacitive-Touch-Display-1366x768_5-point-capacitive.jpg?v=1712561189,https://www.elektor.com/cdn/shop/files/CrowVision-11.6-inch-IPS-Capacitive-Touch-Display-1366x768_viewing-angle.jpg?v=1712561151,https://www.elektor.com/cdn/shop/files/CrowVision-11.6-inch-IPS-Capacitive-Touch-Display-1366x768_included.jpg?v=1712561170https://www.elektor.com/products/crowvision-11-6-ips-capacitive-touch-display-1366x768?variant=47754489561420 in stock 139.95 9 0 0 2 - 4 Werktage 46907036172620 Cytron 10Amp 5-30 V DC Motor Driver Cytron Trade Arduino > Arduino Shields > Bestsellers > Platforms > Raspberry Pi > Raspberry Pi HATs > Robotics 36010398 DC brushed motors are the most commonly used and widely available motors in the market. The Cytron 10 Amp 5-30 V DC Motor Driver will help you add functionality to your DC motor. It supports both sign-magnitude PWM signal and locked-antiphase. It is compatible with full solid-state components resulting in higher response time and eliminates the wear and tear of the mechanical relay. Features Supports motor voltage from 5 V to 30 V DC Current up to 13 A continuous and 30 A peak 3.3 V and 5 V logic level input Compatible with Arduino and Raspberry Pi Speed control PWM frequency up to 20 kHz Fully NMOS H-Bridge for better efficiency No heat sink is required Bi-directional control for one Brushed DC motor Regenerative Braking Downloads User Manual Arduino Library https://www.elektor.com/cdn/shop/files/18998_-_overview-resized.jpg?v=1689085994https://www.elektor.com/cdn/shop/files/18998_-_top_view-resized.jpg?v=1696850179,https://www.elektor.com/cdn/shop/files/18998_-_dimensions.jpg?v=1696850179https://www.elektor.com/products/cytron-10amp-5-30-v-dc-motor-driver?variant=46907036172620 in stock 17.95 25 4.9 6.9 2 - 4 Werktage 46907044135244 Cytron 10Amp 7-30 V DC Motor Driver Shield for Arduino (2 Channels) Cytron Trade Arduino > Arduino Shields > Bestsellers 38514230 You can control the motor driver with PWM and DIR inputs. The Arduino pins for these inputs are configurable via jumpers. If the specified pins on Arduino are already used up by other application/shield, you can select another pin easily with the jumper. There is also a possibility to quickly and conveniently test the functionality of the motor driver with the onboard test buttons and output LEDs. Buck regulator which produces 5 V output is also available to power the Arduino mainboard, which eliminates the need of extra power supply for the Arduino mainboard. The board also offers various protection features. Overcurrent protection prevents the motor driver from damage when the motor stalls or an oversized motor is hooked up. When the motor is trying to draw current more than what the motor driver can support, the motor current will be limited at the maximum threshold. Assisted by temperature protection, the maximum current limiting threshold is determined by the board temperature. The higher the board temperature, the lower the current limiting threshold. As a result, the motor driver delivers its full potential depending on the current conditions without damaging any MOSFETs. Features Shield for Arduino form factor Bidirectional control for two brushed DC motors Control one unipolar/bipolar stepper motor Operating Voltage: DC 7 V to 30 V Maximum Motor Current: 10 A continuous, 30 A peak Buck regulator to produce 5 V output (500 mA max) Buttons for quick testing LEDs for motor output state Selectable Arduino pins for PWM/DIR inputs. PWM/DIR inputs compatible with 1.8 V, 3.3 V and 5 V logic PWM frequency up to 20 kHz (Output frequency is same as input frequency). Overcurrent protection with active current limiting Temperature protection Undervoltage shutdown Possible applications Mobile Robot Automated Guided Vehicle (AGV) Solar Tracker Game Simulator Automation Machine Downloads Datasheet Sample Code 3D CAD Files Packing List 1x 10Amps 7V-30V DC Motor Driver Shield for Arduino (2 Channels) MDD010 https://www.elektor.com/cdn/shop/files/ezgif.com-webp-to-jpg_3.jpg?v=1689086135https://www.elektor.com/cdn/shop/files/4c54-shield-mdd10-b-0-1-0-1-1-800x800.png?v=1696850334,https://www.elektor.com/cdn/shop/files/b4e0-shield-mdd10-c-0-1-0-1-1-800x800.png?v=1696850334,https://www.elektor.com/cdn/shop/files/9629-shield-mdd10_interface_with_truth_table-0-1-0-1-1-800x800.png?v=1698678796,https://www.elektor.com/cdn/shop/files/09e4-shield-mdd10_dimension-0-1-0-1-1-800x800.png?v=1698678796https://www.elektor.com/products/cytron-10amp-7-30-v-dc-motor-driver-shield-for-arduino-2-channels?variant=46907044135244 in stock 29.95 32 4.9 6.9 2 - 4 Werktage 46907043414348 Cytron 25Amp 7-58 V High Voltage DC Motor Driver Cytron Trade Arduino > Arduino Accessories > Bestsellers > Raspberry Pi > Raspberry Pi Accessories 38514079 It is possible to control Cytron 25Amp 7-58 V High Voltage DC Motor Driver with PWM and DIR inputs. The input logic voltage ranges from 1.8 V to 30 V and the board is compatible with variety of host controllers (such as Arduino, Raspberry Pi, PLC). If you don't want to deal with programming to control the motor, there is an option to control the motor driver from a potentiometer (speed) and a switch (direction). You can also test the motor quickly and conveniently using the onboard test buttons and motor output LEDs without the need to hook up the host controller. It is possible to power the host controller with the buck regulator which produces 5 V output. This is especially useful for high voltage applications where no additional power source nor high voltage buck regulator is needed. This motor driver also incorporates various protection features. If the motor stalls or you've hooked up an oversized motor, the overcurrent protection will take care of the board and protect it from damage. If the motor is trying to draw current more than what the motor driver can support, the motor current will be limited at the maximum threshold. Assisted by temperature protection, the maximum current limiting threshold depends on the board temperature. The higher the board temperature, the lower the current limiting threshold. Note: Power input does not have reverse-voltage protection. Connecting the battery in reverse polarity will damage the motor driver instantaneously. Features Bidirectional control for one brushed DC motor Operating Voltage: DC 7 V to 58 V Maximum Motor Current: 25 A continuous, 60 A peak 5 V output for the host controller (250 mA max) Buttons for quick testing LEDs for motor output state Dual Input Mode: PWM/DIR or Potentiometer/Switch Input PWM/DIR Inputs compatible with 1.8 V, 3.3 V, 5 V, 12 V and 24 V logic (Arduino, Raspberry Pi, PLC, etc) PWM frequency up to 40 kHz (Output frequency is fixed at 16 kHz) Overcurrent protection with active current limiting Temperature protection Undervoltage shutdown Scope of delivery 1 × MD25HV (motor driver board) 1 × Potentiometer with connector 1 × Rocker switch with connector 4 × Nylon PCB Standoffs/Spacers Documents Datasheet Sample Code https://www.elektor.com/cdn/shop/files/high_voltage_motor_driver_md25hv-0-1-1-800x800.jpg?v=1698678812https://www.elektor.com/cdn/shop/files/0f16-md25hv_with_accessory-0-1-0-1-1-800x800.jpg?v=1698678812,https://www.elektor.com/cdn/shop/files/effe-high_voltage_motor_driver_md25hv-a-0-1-0-1-1-800x800.png?v=1698678812,https://www.elektor.com/cdn/shop/files/a138-md25hv__dimension-0-1-0-1-1-800x800.jpg?v=1698678812,https://www.elektor.com/cdn/shop/files/df5f-high_voltage_motor_driver_md25hv-b-0-1-0-1-1-800x800.png?v=1698678812,https://www.elektor.com/cdn/shop/files/bb3c-high_voltage_motor_driver__interface_mode_2-0-1-0-1-1-800x800.jpg?v=1698678812,https://www.elektor.com/cdn/shop/files/cebf-high_voltage_motor_driver__interface_mode_1-0-1-0-1-1-800x800.jpg?v=1698678812https://www.elektor.com/products/cytron-25amp-7-58-v-high-voltage-dc-motor-driver?variant=46907043414348 in stock 62.95 26 0 6.9 2 - 4 Werktage 46907036303692 Cytron 3Amp 4-16 V DC Motor Driver (2 Channels) Cytron Trade Arduino > Arduino Shields > Bestsellers > Platforms > Raspberry Pi > Raspberry Pi HATs > Robotics 38514118 Features: Supports motor voltage from 4 V to 16 V DC Bidirectional control for two brushed DC motor. Control one unipolar or one bipolar stepper motor. Maximum Motor Current: 3A continuous, 5A peak LEDs for motor output state. Buttons for quick testing. Compatible with Arduino and Raspberry Pi PWM frequency up to 20kHz Reverse polarity protection Here you can find the product's Datasheet. Check out the sample code provided by Cytron here. https://www.elektor.com/cdn/shop/files/18999_-_overview-resized.jpg?v=1689086001https://www.elektor.com/cdn/shop/files/18999_-_dimensions-resized.jpg?v=1696850187,https://www.elektor.com/cdn/shop/files/18999_-_case-resized.jpg?v=1696850188https://www.elektor.com/products/cytron-3amp-4-16-v-dc-motor-driver-2-channels?variant=46907036303692 in stock 10.95 14 4.9 6.9 2 - 4 Werktage 46907028898124 Cytron Maker Drive - H-Bridge Motor Driver Cytron Trade Bestsellers > Components > Modules 38514089 Features Dual channel, Bi-directional control motor driver Support motor voltage from 2.5 V to 9.5 V DC Maximum current up to 1.0 A continuous and 1.5 A peak (<5 seconds) 5 V Output (200 mA) to power the controller. Inputs compatible with 1.8 V, 3.3 V and 5 V logic (Arduino, Raspberry Pi, etc). Solid state components provide faster response time and eliminate the wear and tear of mechanical relay Regenerative Braking Speed control PWM frequency up to 20 KHz (Actual output frequency is same as input frequency) Dimension: 43 mm (W) x 35 mm (L) x 14 mm (H) The Problem Faced by Beginners in Driving DC Brushed Motor Maker Drive is designed by taking into account feedback from users, especially 1st time users. If you are a beginner that needs a simple motor driver to drive DC brushed motor for building mobile robot or other purposes, you might come across some of these obstacles: Burning your Motor Driver - Many low cost motor driver does not come with Reserve Polarity Protection and this might result in smoke coming out from the driver if you connect the power in wrong polarity. This gives you a burnt motor driver and of course the waste of money and your precious time. Too Bulky for compact projects - Some motor drivers come with a big heat sink and take up too much space. Hard to test and troubleshoot - With normal motor drivers, beginners face a common problem during building project - difficulty in testing and troubleshooting the circuit. Yes, even with a clear schematic or diagram, the circuit will not work right after you complete the connection. Most of the time, you will need to test or troubleshoot. Without easy to use input and output indicator, you will need to write a program to test the motor driver. And that increases the complexity of debugging as you do not know whether the problem is due to wire connection or coding in your program. Separate Power for Low Voltage Motor - Many low cost motor drivers have an onboard 5 V linear voltage regulator, which is great to power your controller like Arduino. But this linear voltage regulator will not output 5 V if Vin is lower than 7 V. Yet, many small toy motors used in DIY projects are rated at lower than 7 V. These motors are suitable to be powered by two AA or AAA batteries (3 V or less) or single cell Li-ion 18650/Li-Po battery (3.7 V rated voltage). With that, you will need two separate power sources, one for the motors and another one to get stable 5 V output for controller such as Arduino board. Maker Drive is designed to solve the above problems while adding some useful features: Fool Proof - Maker Drive comes with Reverse Polarity Protection at Vin/Vmotor/Vbatt (Power for motor) terminal. With this protection it will greatly reduce the risk of damaging the motor driver Compact Design - Maker Drive is designed to be compact, roughly the size of a passport photo, 43 mm (W) x 35 mm (L) x 14 mm (H) 4 Test Buttons (2 for each channel) - Easily test the motor or your mechanism without any controller or coding. Maker Drive comes with two manual test buttons for each channel. Pressing one of the buttons will drive the output full speed in a direction (if there is motor connected) on respective channel. While another button will drive the output in another direction. These buttons are useful to test the motor direction, connection and operation; even without controller. You can also use these buttons as manual activation button. No programming is needed to use these buttons. 4 Indicator LEDs (2 for each channel) - Easily test your coding and wire connections. With these indicator LEDs, you can check output voltage direction even without connecting the driver to your motor. And combining with the Manual Test Buttons, you can test the Maker Drive easily even without controller and motor connected. You can also easily identify where the error occurs for easy troubleshooting. Of course no programming is needed here either. These LEDs are qu... https://www.elektor.com/cdn/shop/files/8b61-maker_drive_terminal_b-0-1-0-1-1-800x800_1.jpg?v=1689085770https://www.elektor.com/cdn/shop/files/60d8-maker-drive_-_top-0-1-0-1-1-800x800_1.jpg?v=1696850003,https://www.elektor.com/cdn/shop/files/a221-makerdriveconnection-0-1-0-1-1-800x800_1.jpg?v=1696850003,https://www.elektor.com/cdn/shop/files/7a3c-maker-drive_-_btm-0-1-0-1-1-800x800_1.jpg?v=1698678833,https://www.elektor.com/cdn/shop/files/maker-drive_-_iso-0-1-1-800x800_1.jpg?v=1698678833,https://www.elektor.com/cdn/shop/files/f182-maker_drive_terminal-0-1-0-1-1-800x800_1.jpg?v=1698678832,https://www.elektor.com/cdn/shop/files/f857-makerdrivesize-0-1-0-1-1-800x800_1.jpg?v=1698678833,https://www.elektor.com/cdn/shop/files/s6lsiv4oqe6g0cjl7rbzoua_1.png?v=1698678833https://www.elektor.com/products/cytron-maker-drive-h-bridge-motor-driver?variant=46907028898124 in stock 8.95 20 4.9 6.9 2 - 4 Werktage 46907195687244 Cytron Maker Hat Base - HAT & GPIO Extension for Raspberry Pi 400 Cytron Trade Bestsellers > NEW > No Member Discount > Raspberry Pi > Raspberry Pi HATs > Sale 38515730 Maker Hat Base extends out all the GPIOs of the Raspberry Pi 400 in a quick and simple way – be it using your favorite HAT or building your own simple circuit with jumper wires on the mini breadboard.Since a ribbon cable is used for the connection, the Maker Hat Base is compatible with the Raspberry Pi 3 and Pi 4 too. This is especially useful when the Raspberry Pi is enclosed in a case and you want to extend its GPIOs out for HAT.Each GPIO pin is clearly labeled and its status LED is definitely helpful during testing and troubleshooting. The onboard buzzer and push buttons will get you to start coding in no time without the need of building your own circuit. FeaturesSpecially designed for Raspberry Pi 400Compatible with Raspberry Pi 3 & 4Extension pins for HATLabeled GPIOs breakout for jumper wiresStatus LEDs for each GPIOs1x programmable buzzer4x programmable push buttons3x Grove ports (GPIO, UART & I²C) for external modulesOnboard 3.3 V regulator provides extra current up to 800 mAIncluded1x Maker Hat Base1x Mini Breadboard (Random Color)1x 40 Ways Female to Female IDE cable (10 cm)1x Flat Cable Clamper with Adhesive (60 mm)4x Silicone Bumper1x PC104 2x20 Header PinDownloadsDatasheetCAD File https://www.elektor.com/cdn/shop/files/cytron_maker_hat_base_hat_gpio_extension_for_raspberry_pi_400.jpg?v=1689089935https://www.elektor.com/products/cytron-maker-hat-base-hat-gpio-extension-for-raspberry-pi-400?variant=46907195687244 in stock 19.95 12.95 11 4.9 6.9 2 - 4 Werktage 46907044495692 Cytron Maker Line Sensor Cytron Trade Bestsellers > Components > Sensors & LiDAR 38514401 Maker Line is a line sensor with 5 x IR sensors array that is able to track line from 13 mm to 30 mm width. The sensor calibration is also simplified. There is no need to adjust the potentiometer for each IR sensor. You just have to press the calibrate button for 2 seconds to enter calibration mode. Afterwards you need to sweep the sensors array across the line, press the button again and you are good to go. The calibration data is saved in EEPROM and it will stay intact even if the sensor has been powered off. Thus, calibration only needs to be carried out once unless the sensor height, line color or background color has changed. Maker Line also supports dual outputs: 5 x digital outputs for the state of each sensor independently, which is similar to conventional IR sensor, but you get the benefit of easy calibration, and also one analog output, where its voltage represents the line position. Analog output also offers higher resolution compared to individual digital outputs. This is especially useful when high accuracy is required while building a line following robot with PID control. Features Operating Voltage: DC 3.3 V and 5 V compatible (with reverse polarity protection) Recommended Line Width: 13 mm to 30 mm Selectable line color (light or dark) Sensing Distance (Height): 4 mm to 40 mm (Vcc = 5 V, Black line on white surface) Sensor Refresh Rate: 200 Hz Easy calibration process Dual Output Types: 5 x digital outputs represent each IR sensor state, 1 x analog output represents line position. Support wide range of controllers such as Arduino, Raspberry Pi etc. Documentation Datasheet Tutorial: Building A Low-Cost Line Following Robot https://www.elektor.com/cdn/shop/files/maker_line-0-1-1-800x800.png?v=1689086143https://www.elektor.com/cdn/shop/files/c723-maker_line_bottom-5-1-0-1-1-800x800.png?v=1696850343,https://www.elektor.com/cdn/shop/files/ea36-maker_line_top-5-1-0-1-1-800x800.png?v=1696850343,https://www.elektor.com/cdn/shop/files/maker-line_interface_-_digital.jpg?v=1698678850,https://www.elektor.com/cdn/shop/files/maker-line_interface_-_analog.jpg?v=1698678849https://www.elektor.com/products/cytron-maker-line-sensor?variant=46907044495692 in stock 14.95 34 4.9 6.9 2 - 4 Werktage 46907029455180 Cytron Maker pHAT for Raspberry Pi Cytron Trade Bestsellers > Raspberry Pi > Raspberry Pi HATs 38513981 The Maker pHAT is the solution to the most common problems beginners face starting with Raspberry PI. Its intelligent and simple design makes it easy to attach to your Pi, and it helps you avoid all the tedious work of connection various other accessories. Additionally, the LEDs corresponding to each pin makes it extremely easy to see where a potential problem lies The Maker pHat has the same size as the Raspberry Pi Zero with all 4mounting holes aligned. However, it can be used with Raspberry Pi 3B, 3B+ and 3A+, by inserting a 2 x 20 stacking header. Features Raspberry Pi Zero size, stack perfectly on to Raspberry Pi Zero Compatible with standard size Raspberry Pi 3B / 3B+, medium size Raspberry Pi 3A+ and smaller size Raspberry Pi Zero / W / WH. Standard Raspberry Pi GPIO footprint. LED array for selected GPIO pins (GPIO 17, 18, 27, 22, 25, 12, 13, 19). 3x on board programmable push buttons (GPIO 21, 19 and 20, need to configure as input pull up). Onboard active buzzer (GPIO 26). Proper labels for all GPIOs, including SPI, UART, I2C, 5V, 3.3V, and GND. Utilize USB Micro-B socket for 5V input and USB to UART communication. USB serial facilitated by the FT231X Input voltage: USB 5 V, from a computer, power bank or a standard USB adapter. Mount on Raspberry Pi Zero Mount on Raspberry Pi 3B, 3B+ and 3A+ https://www.elektor.com/cdn/shop/files/18925_-_overview-resized_1.jpg?v=1689085778https://www.elektor.com/cdn/shop/files/18925_-_bottom_view-resized_1.jpg?v=1696850014,https://www.elektor.com/cdn/shop/files/18925_-_mounted_on_pi_zero-resized_1.jpg?v=1696850013,https://www.elektor.com/cdn/shop/files/18925_-_mounted_on_pi_3a_-resized_1.jpg?v=1696850014,https://www.elektor.com/cdn/shop/files/18925_-_mounted_on_pi_3b-resized_1.jpg?v=1696850014https://www.elektor.com/products/cytron-maker-phat-for-raspberry-pi?variant=46907029455180 in stock 14.95 14 4.9 6.9 2 - 4 Werktage 46907143782732 Cytron Maker Pi Pico (with pre-soldered Raspberry Pi Pico) Cytron Trade Bestsellers > Pico RP2040 > Raspberry Pi 019706 The Cytron Maker Pi Pico (with Raspberry Pi Pico RP2040 soldered on Board) incorporates the most wanted features for your Raspberry Pi Pico and gives you access to all GPIO pins on two 20 ways pin-headers, with clear labels. Each GPIO is coupled with an LED indicator for convenient code testing and troubleshooting. The bottom layer of this board even comes with a comprehensive pinout diagram showing the function of each pin. Features Work out-of-the-box. No soldering! Access to all Raspberry Pi Pico's pins on two 20 ways pin headers LED indicators on all GPIO pins 3x programmable push button (GP20-22) 1x RGB LED – NeoPixel (GP28) 1x Piezo buzzer (GP18) 1x 3.5 mm stereo audio jack (GP18-19) 1x Micro SD card slot (GP10-15) 1x ESP-01 socket (GP16-17) 6x Grove port Specifications Core 32-bit ARM Cortex-M0+ CPU Clock 48 MHz, up to 133 MHz Flash Size 2 MByte Q-SPI Flash Programming Language MicroPython, C++ Board Power Input 5 VDC via MicroUSB Alternative Board Power 2-5 VDC via VSYS Pin (Pin 39) MCU Voltage 3.3 VDC GPIO Voltage 3.3 VDC USB Interface USB 1.1 Device Host Program Loading MicroUSB, USB Mass Storage GPIO 26x Input/Output ADC 3x 12-bit 500 ksps Temperature Sensor Built-in, 12-bit UART 2x UART I²C 2x I²C SPI 2x SPI PWM 16x PWM Timer 1x Timer with 4 x Alarm Real-Time Counter 1x Real Time Counter PIO 2x Programmable High-Speed I/O On-Board LED 1x Programmable LED On-Board Button 1x BOOTSEL Button https://www.elektor.com/cdn/shop/files/cytron_maker_pi_pico_with_raspberry_pi_pico_rp2040_soldered_on_board_-_overview.jpg?v=1689088532https://www.elektor.com/cdn/shop/files/cytron_maker_pi_pico_with_raspberry_pi_pico_rp2040_soldered_on_board_-_top_view.jpg?v=1696851858,https://www.elektor.com/cdn/shop/files/cytron_maker_pi_pico_with_raspberry_pi_pico_rp2040_soldered_on_board_-_gpio.png?v=1696851857,https://www.elektor.com/cdn/shop/files/cytron_maker_pi_pico_with_raspberry_pi_pico_rp2040_soldered_on_board.png?v=1698678871,https://www.elektor.com/cdn/shop/files/cytron_maker_pi_pico_with_raspberry_pi_pico_rp2040_soldered_on_board_-_dimensions_1.png?v=1698678871https://www.elektor.com/products/cytron-maker-pi-pico-with-pre-soldered-raspberry-pi-pico?variant=46907143782732 in stock 24.95 18 4.9 6.9 2 - 4 Werktage 46907254899020 Cytron Maker Pi Pico Mini W (with pre-soldered Raspberry Pi Pico W & preloaded CircuitPython) Cytron Trade Bestsellers > Pico RP2040 > Raspberry Pi 020411 Love the Cytron Maker Pi Pico (SKU 19706) but can't fit it into your project? Now there is the Cytron Maker Pi Pico Mini W. Powered by the awesome Raspberry Pi Pico W, it also inherited most of the useful features from its bigger sibling such as GPIO status LEDs, WS2812B Neopixel RGB LED, passive piezo buzzer, and not forget the user button and reset button. Features Powered by Raspberry Pi Pico W Single-cell LiPo connector with overcharge / over-discharge protection circuit, rechargeable via USB. 6x Status indicator LEDs for GPIOs 1x Passive piezo buzzer (Able to play musical tone or melody) 1x Reset button 1x User programmable button 1x RGB LEDs (WS2812B Neopixel) 3x Maker Ports, compatible with Qwiic, STEMMA QT, and Grove (via conversion cable) Support Arduino IDE, CircuitPython and MicroPython Dimension: 23.12 x 53.85 mm Included 1x Maker Pi Pico Mini W (pre-soldered Raspberry Pi Pico W with preloaded CircuitPython) 3x Grove to JST-SH (Qwiic / STEMMA QT) Cable Downloads Maker Pi Pico Mini Datasheet Maker Pi Pico Mini Schematic Maker Pi Pico Mini Pinout Diagram Official Raspberry Pi Pico Page Getting started with Raspberry Pi Pico CircuitPython for Raspberry Pi Pico Raspberry Pi Pico Datasheet RP2040 Datasheet Raspberry Pi Pico Python SDK Raspberry Pi Pico C/C++ SDK https://www.elektor.com/cdn/shop/files/cytron-maker-pi-pico-mini-w.jpg?v=1689092164https://www.elektor.com/cdn/shop/files/cytron-maker-pi-pico-mini-w_sides.jpg?v=1696854490,https://www.elektor.com/cdn/shop/files/cytron-maker-pi-pico-mini-w_features.jpg?v=1696854490https://www.elektor.com/products/cytron-maker-pi-pico-mini-w-with-pre-soldered-raspberry-pi-pico-w-preloaded-circuitpython?variant=46907254899020 in stock 19.95 14 4.9 6.9 2 - 4 Werktage 46907188805964 Cytron Maker Pi RP2040 - Robotics with Raspberry Pi RP2040 Cytron Trade Bestsellers > Pico RP2040 > Platforms > Raspberry Pi > Robotics 38515893 Cytron Maker Pi RP2040 features the first microcontroller designed by Raspberry Pi – RP2040, embedded on a robot controller board. This board comes with dual channel DC motor driver, 4 servo motor ports and 7 Grove I/O connectors, ready for your next DIY robot / motion control project. Now you can build robot, while trying out the new RP2040 chip. The DC motor driver onboard is able to control 2x brushed DC motors or 1x bipolar/unipolar stepper motor rated from 3.6 V to 6 V, providing up to 1 A current per channel continuously. The built-in Quick Test buttons and motor output LEDs allow functional test of the motor driver in a quick and convenient way, without the need of writing any code. Vmotor for both DC and servo motors depends on the input voltage supplied to the board. Maker Pi RP2040 features all the goodness of Cytron's Maker series products. It too has lots of LEDs useful for troubleshooting (& visual effects), is able to make quite some noise with the onboard piezo buzzer and comes with push buttons ready to detect your touch. There are three ways to supply power to the Maker Pi RP2040 – via USB (5 V) socket, with a single cell LiPo/Li-Ion battery or through the VIN (3.6-6 V) terminals. However only one power source is needed to power up both controller board and motors at a time. Power supply from all these power sources can all be controlled with the power on/off switch onboard. Cytron Maker Pi RP2040 is basically the Raspberry Pi Pico + Maker series' goodness + Robot controller & other useful features. Therefore this board is compatible with the existing Pico ecosystem. Software, firmware, libraries and resources that are developed for Pico should work seamlessly with Cytron Maker Pi RP2040 too. CircuitPython is preloaded on the Maker Pi RP2040 and it runs a simple demo program right out-of-the-box. Connect it to your computer via USB micro cable and turn it on, you will be greeted by a melody tune and LEDs running light. Press GP20 and GP21 push buttons to toggle the LEDs on/off, while controlling any DC and servo motors connected to it to move and stop. With this demo code, you get to test the board the moment you receive it! While connected to your computer, a new CIRCUITPY drive appears. Explore and edit the demo code (code.py & lib folder) with any code editor you like, save any changes to the drive and you shall see it in action in no time. That's why we embrace CircuitPython – it's very easy to get started. Wish to use other programming lauguages? Sure, you are free to use MicroPython and C/C++ for Pico/RP2040. For those of you who loves the Arduino ecosystem, please take a look at this official news by Arduino and also the unofficial Pico Arduino Core by Earle F. Philhower. Features Powered by Rapberry Pi RP2040 Dual-core Arm Cortex-M0+ processor 264 KB internal RAM 2 MB of Flash memory the exact same specifications with Raspberry Pi Pico Robot controller board 4x Servo motors 2x DC motors with quick test buttons Versatile power circuit Automatic power selection: USB 5 V, LiPo (1-cell) or Vin (3.6-6 V) Built-in 1-cell LiPo/Li-Ion charger (over-charged & over-discharged protection) Power on/off switch 13x Status indicator LEDs for GPIO pins 1x Piezo buzzer with mute switch 2x Push button 2x RGB LED (Neopixel) 7x Grove ports (flexible I/O options: digital, analog, I²C, SPI, UART...) Preloaded with CircuitPython by default Mouting holes 4x 4.8 mm mounting hole (LEGO pin compatible) 6x M3 screw hole https://www.elektor.com/cdn/shop/files/cytron-maker-pi-rp2040.jpg?v=1689089642https://www.elektor.com/cdn/shop/files/cytron-maker-pi-rp2040_front.jpg?v=1696852634,https://www.elektor.com/cdn/shop/files/cytron-maker-pi-rp2040_back.jpg?v=1696852635,https://www.elektor.com/cdn/shop/files/cytron-maker-pi-rp2040_chip.jpg?v=1698678881https://www.elektor.com/products/cytron-maker-pi-rp2040-robotics-with-raspberry-pi-rp2040?variant=46907188805964 in stock 16.95 3 4.9 6.9 2 - 4 Werktage 46907002290508 Cytron Maker Uno Cytron Trade Arduino > Arduino Boards > Bestsellers > Components > Development Boards 38512318 Features Piezo Buzzer: Acts as a simple audio output Micro USB Port Programmable Button 12 x LED: Provides visual output on board Specifications Microcontroller ATmega328P Programming IDE Arduino IDE Operating Voltage 5 V Digital I/O 20 PWM 6 Analog Input 6 (10-bit) UART 1 SPI 1 I2C 1 External Interrupt 2 Flash Memory 32 KB SRAM 2 KB EEPROM / Data Flash 1 KB Clock Speed 16 MHz DC Current I/O Pin 20 mA Power Supply USB only DC Current for 5 V USB Source DC Current for 3.3 V 500 mA USB to Serial Chip CH340G Programmable LED 12 at digital Pin 2 to 13 Programmable Push Button 1 at digital Pin 2 Piezo Buzzer 1 at digital Pin 8 Arduino vs Maker Uno https://www.elektor.com/cdn/shop/files/18634_-_overview-resized.jpg?v=1698678895https://www.elektor.com/cdn/shop/files/18634_-_specs-resized.jpg?v=1698678895,https://www.elektor.com/cdn/shop/files/18634_-_topview-resized.jpg?v=1698678895,https://www.elektor.com/cdn/shop/files/18634_-_sign-resized.jpg?v=1698678895,https://www.elektor.com/cdn/shop/files/18634_-_pin_config-resized.jpg?v=1698678895,https://www.elektor.com/cdn/shop/files/18634_-_box-resized.jpg?v=1698678895https://www.elektor.com/products/cytron-maker-uno?variant=46907002290508 in stock 14.95 8 4.9 6.9 2 - 4 Werktage 46907195588940 Cytron REKA:BIT - Robotics with micro:bit Cytron Trade BBC micro:bit > Bestsellers > Platforms > Robotics 38515775 Program your REKA:BIT with Microsoft MakeCode Editor. Just add REKA:BIT MakeCode Extension and you’re good to go. If you’re a beginner, you can start with the block programming mode; simply drag, drop and snap the coding blocks together. For more advanced users, you can easily switch into JavaScript or Python mode on MakeCode Editor for text-based programming.REKA:BIT possesses a lot of indicator LEDs to assist your coding and troubleshooting. It covers the IO pins connected to all six Grove ports and DC motor outputs from the co-processor. One is able to check his/her program and circuit connection easily by monitoring these LEDs.Besides, REKA:BIT also has a power on/off indicator, undervoltage, and overvoltage LEDs built-in to give appropriate warnings should there be any problem with the power input.REKA:BIT features a co-processor to handle multitasking more efficiently. Playing music while controlling up to 4x servo motors and 2x DC motors, animating micro:bit LED matrix, and even lighting up RGB LEDs in different colors, all at the same time, is not a problem for REKA:BIT.Features2x DC motor terminalsBuilt-in motor quick test buttons (no coding needed)4x Servo motor ports2x Neopixel RGB LEDs6x Grove port (3.3 V)3x Analog Input / Digital IO ports2x Digital IO ports1x I²C InterfaceDC jack for power input (3.6 - 6 VDC)ON/OFF switchPower on indicatorUndervoltage (LOW) indicator & protectionOver-voltage (HIGH) indicator & protectionDimensions: 10.4 x 72 x 15 mmIncluded1x REKA:BIT expansion board1x USB power and data cable1x 4xAA battery holder1x Mini screwdriver3x Grove to female header cable2x Building block 1x9 lift arm4x Building block friction pinPlease note: micro:bit board not included https://www.elektor.com/cdn/shop/files/cytron_reka-bit_robotics_with_micro-bit_micro-bit_not_included_-_overview.jpg?v=1689089928https://www.elektor.com/cdn/shop/files/cytron_reka-bit_robotics_with_micro-bit_micro-bit_not_included_-_back.jpg?v=1696852826,https://www.elektor.com/cdn/shop/files/cytron_reka-bit_robotics_with_micro-bit_micro-bit_not_included_-_assembled.png?v=1696852826https://www.elektor.com/products/cytron-reka-bit-robotics-with-micro-bit?variant=46907195588940 in stock 22.95 17 4.9 6.9 2 - 4 Werktage 47310492500300 DER EE DE-5000 LCR Meter (100 kHz) Elektor Trade Bestsellers > LCR Meters > Measuring Tools > NEW > Test & Measurement 020675 The DE-5000 is a smart, high-accurate, flexible and easy-to-use portable LCR meter. It features automatic LCR check, 4-wire Kelvin measurement, backlit display with 19999/1999 counts, multiple measurement modes and selectable test frequencies (100 Hz, 120 Hz, 1 kHz, 10 kHz or 100 kHz). The DE-5000 LCR meter is a practical helper for engineers or technicians. Features Auto L.C.R. check Ls/Lp/Cs/Cp/Rs/Rp/DCR with D/Q/θ/ESR measurement 4-wire Kelvin measurement 20,000 / 2,000 counts display Backlight Relative mode Series / Parallel modes Components sorting function Low battery indication Auto power off Specifications Test frequency 100 Hz / 120 Hz / 1 kHz / 10 kHz / 100 kHz Resistance range 20.000 Ω – 200.0 MΩ DCR range 200.00 Ω – 200.0 MΩ Capacitance range 200.00 pF – 20.00 mF Inductance range 20.000 µH – 2.000 KH Display (backlit LCD) 19999 / 1999 counts Selectable tolerance ±0.25%, ±0.5%, ±1%, ±2%, ±5%, ±10%, ±20% Power supply 9 V battery Dimensions 188 x 95 x 52 mm Weight 350 g (excluding battery) Included DE-5000 LCR meter Alligator test lead case (TL-21) AC/DC adaptor Guard line (TL-23) TL-22 SMD tweezers 9 V battery Carrying case Manual Downloads Datasheet https://www.elektor.com/cdn/shop/files/DER-EE-DE-5000-LCR-Meter.jpg?v=1701969254https://www.elektor.com/products/der-ee-de-5000-lcr-meter-100-khz?variant=47310492500300 in stock 219.0 23 0 0 2 - 4 Werktage 46906978697548 Design your own Embedded Linux Control Centre (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906978697548-has-digital-downloads This e-book (pdf) is all about building your own DIY home control system. It presents two innovative ways to assemble such a system: By recycling old PC hardware - possibly extending the life of an old PC, or by using Raspberry Pi. In both cases, the main system outlined in this e-book will consist of a computer platform, a wireless mains outlet, a controller and a USB webcam - All linked together by Linux. By using the Raspberry Pi in conjunction with Arduino (used as an advanced I/O system board), it is possible to construct a small, compact, embedded control system offering enhanced capacity for USB integration, webcams, thermal monitoring and communication with the outside world. The experience required to undertake the projects within this e-book are minimal exposure to PC hardware and software, the ability to surf the internet, burn a CD-ROM and assemble a small PCB. All custom software is available for free download (see 'attachments/downloads' section on this page). https://www.elektor.com/cdn/shop/files/design-your-own-embedded-linux-control-centre-3_ebook.jpg?v=1689084579https://www.elektor.com/products/design-your-own-embedded-linux-control-centre-ebook?variant=46906978697548 in stock 32.95 0 4.9 6.9 2 - 4 Werktage 46907067957580 Designing Audio Power Amplifiers (2nd Edition) Elektor Trade Bestsellers > Books > Books | Audio & RF 09781138555440 This comprehensive book on audio power amplifier design will appeal to members of the professional audio engineering community as well as the student and enthusiast. Designing Audio Power Amplifiers begins with power amplifier design basics that a novice can understand and moves all the way through to in-depth design techniques for very sophisticated audiophiles and professional audio power amplifiers. This book is the single best source of knowledge for anyone who wishes to design audio power amplifiers. It also provides a detailed introduction to nearly all aspects of analog circuit design, making it an effective educational text. Develop and hone your audio amplifier design skills with in-depth coverage of these and other topics: Basic and advanced audio power amplifier design Low-noise amplifier design Static and dynamic crossover distortion demystified Understanding negative feedback and the controversy surrounding it Advanced NFB compensation techniques, including TPC and TMC Sophisticated DC servo design MOSFET power amplifiers and error correction Audio measurements and instrumentation Overlooked sources of distortion SPICE simulation for audio amplifiers, including a tutorial on LTspice SPICE transistor modeling, including the VDMOS model for power MOSFETs Thermal design and the use of ThermalTrak transistors Four chapters on class D amplifiers, including measurement techniques Professional power amplifiers Switch-mode power supplies (SMPS) https://www.elektor.com/cdn/shop/files/designing_audio_power_amplifiers.jpg?v=1689086396https://www.elektor.com/cdn/shop/files/designing_audio_power_amplifiers_-_back.jpg?v=1696850519https://www.elektor.com/products/designing-audio-power-amplifiers-2nd-edition?variant=46907067957580 in stock 92.5 7 0 6.9 2 - 4 Werktage 47571256148300 Designing Tube Amplifiers (E-book) Elektor Digital E-books Bestsellers > E-books (–20% for Members) has-digital-downloads,variant-47571256148300-has-digital-downloads - This book focuses more on practical aspects than on theory, and it has an contemplative nature, as though the author were viewing amplifiers from above. Knowledge elements are integrated and placed in the context of a broad overview.Even now tube amplifiers still sound great perhaps better than ever before. In part that is because we now have access to modern components such as toroidal output transformers, extremely high-quality resistors and capacitors, and many sorts of wire with good acoustic properties. Modern audio sources, such as CD players, and the latest top-end loudspeakers also enable us to appreciate how well tube amplifiers reproduce music even better than before.This new book from Menno van der Veen looks at tube amplifiers from more than just a theoretical perspective. It focuses primarily on the design phase, where decisions must be taken with regard to the purpose and requirements of the amplifier, and it addresses the following questions: How do these aspects relate to subjective and objective criteria? Which circuits sound the best, and why? If you want to develop and market an amplifier, what problems should you expect? What are the significance and meaning of measurements? Are they still meaningful, or have they lost their relevance?Thanks to the enormous processing power of computers, we can now measure more details than ever before. How can these new methods be applied to tube amplifiers? Previously it was sufficient to measure the frequency range, power and distortion of an amplifier in order to characterize the amplifier. Are these measurements still sufficient, or should we start measuring according to how we hear, using real music signals instead of waveforms from signal generators? The author sketches a future where amplifier measurements that conform to our sense of hearing enable us to arrive at new insights.This book focuses more on practical aspects than on theory, and it has an contemplative nature, as though the author were viewing amplifiers from above. Knowledge elements are integrated and placed in the context of a broad overview. https://www.elektor.com/cdn/shop/files/designing-tube-amplifiers.png?v=1705319550https://www.elektor.com/cdn/shop/files/designing-tube-amplifiers.jpg?v=1705319552https://www.elektor.com/products/designing-tube-amplifiers-ebook?variant=47571256148300 in stock 23.95 0 4.9 6.9 2 - 4 Werktage 47310492729676 Desoldering Tip Set for Desoldering Station ZD-915 Zhongdi Trade Bestsellers > Soldering Accessories 020547 This set contains 3 desoldering tips for the digital desoldering station ZD-915. Included 1x Desoldering tip N5-1 (0.8 mm) 1x Desoldering tip N5-2 (1.0 mm) 1x Desoldering tip N5-3 (1.3 mm) https://www.elektor.com/cdn/shop/files/desoldering-tip-set-for-zd-915.jpg?v=1699286954https://www.elektor.com/cdn/shop/files/desoldering-tip-set-for-zd-915_specs.jpg?v=1699286955https://www.elektor.com/products/desoldering-tip-set-for-desoldering-station-zd-915?variant=47310492729676 in stock 12.95 178 4.9 6.9 2 - 4 Werktage 46907221344588 Develop and Operate Your LoRaWAN IoT Nodes Elektor Publishing Books Bestsellers > Books > Books | Electronics > Books | IoT & Automation > NEW > Print Books > Programming Elektor Print Book 9783895764943 Ready-to-use devices and self-built Arduino nodes in the 'The Things Network' LoRaWAN has developed excellently as a communication solution in the IoT. The Things Network (TTN) has contributed to this. The Things Network was upgraded to The Things Stack Community Edition (TTS (CE)). The TTN V2 clusters were closed towards the end of 2021. This book shows you the necessary steps to operate LoRaWAN nodes using TTS (CE) and maybe extend the network of gateways with an own gateway. Meanwhile, there are even LoRaWAN gateways suitable for mobile use with which you can connect to the TTN server via your cell phone. The author presents several commercial LoRaWAN nodes and new, low-cost and battery-powered hardware for building autonomous LoRaWAN nodes. Registering LoRaWAN nodes and gateways in the TTS (CE), providing the collected data via MQTT and visualization via Node-RED, Cayenne, Thingspeak, and Datacake enable complex IoT projects and completely new applications at very low cost. This book will enable you to provide and visualize data collected with battery-powered sensors (LoRaWAN nodes) wirelessly on the Internet. You will learn the basics for smart city and IoT applications that enable, for example, the measurement of air quality, water levels, snow depths, the determination of free parking spaces (smart parking), and the intelligent control of street lighting (smart lighting), among others. https://www.elektor.com/cdn/shop/files/develop-and-operate-your-lorawan-iot-nodes.png?v=1689090771https://www.elektor.com/products/develop-and-operate-your-lorawan-iot-nodes?variant=46907221344588 in stock 32.95 9 4.9 6.9 2 - 4 Werktage 46907221377356 Develop and Operate Your LoRaWAN IoT Nodes (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907221377356-has-digital-downloads 978-3-89576-495-0 Ready-to-use devices and self-built Arduino nodes in the 'The Things Network' LoRaWAN has developed excellently as a communication solution in the IoT. The Things Network (TTN) has contributed to this. The Things Network was upgraded to The Things Stack Community Edition (TTS (CE)). The TTN V2 clusters were closed towards the end of 2021. This book shows you the necessary steps to operate LoRaWAN nodes using TTS (CE) and maybe extend the network of gateways with an own gateway. Meanwhile, there are even LoRaWAN gateways suitable for mobile use with which you can connect to the TTN server via your cell phone. The author presents several commercial LoRaWAN nodes and new, low-cost and battery-powered hardware for building autonomous LoRaWAN nodes. Registering LoRaWAN nodes and gateways in the TTS (CE), providing the collected data via MQTT and visualization via Node-RED, Cayenne, Thingspeak, and Datacake enable complex IoT projects and completely new applications at very low cost. This book will enable you to provide and visualize data collected with battery-powered sensors (LoRaWAN nodes) wirelessly on the Internet. You will learn the basics for smart city and IoT applications that enable, for example, the measurement of air quality, water levels, snow depths, the determination of free parking spaces (smart parking), and the intelligent control of street lighting (smart lighting), among others. https://www.elektor.com/cdn/shop/files/develop-and-operate-your-lorawan-iot-nodes-pdf.png?v=1689090777https://www.elektor.com/products/develop-and-operate-your-lorawan-iot-nodes-e-book?variant=46907221377356 in stock 27.95 0 4.9 6.9 2 - 4 Werktage 46907227111756 Develop your own Bluetooth Low Energy Applications Elektor Publishing Books Bestsellers > Books > Books | Electronics > NEW > Print Books > Programming > Raspberry Pi | Arduino | ESP Elektor Print Book 9783895765001 For Raspberry Pi, ESP32 and nRF52 with Python, Arduino and Zephyr Bluetooth Low Energy (BLE) radio chips are ubiquitous from Raspberry Pi to light bulbs. BLE is an elaborate technology with a comprehensive specification, but the basics are quite accessible. A progressive and systematic approach will lead you far in mastering this wireless communication technique, which is essential for working in low power scenarios. In this book, you’ll learn how to: Discover BLE devices in the neighborhood by listening to their advertisements. Create your own BLE devices advertising data. Connect to BLE devices such as heart rate monitors and proximity reporters. Create secure connections to BLE devices with encryption and authentication. Understand BLE service and profile specifications and implement them. Reverse engineer a BLE device with a proprietary implementation and control it with your own software. Make your BLE devices use as little power as possible. This book shows you the ropes of BLE programming with Python and the Bleak library on a Raspberry Pi or PC, with C++ and NimBLE-Arduino on Espressif’s ESP32 development boards, and with C on one of the development boards supported by the Zephyr real-time operating system, such as Nordic Semiconductor's nRF52 boards. Starting with a very little amount of theory, you’ll develop code right from the beginning. After you’ve completed this book, you’ll know enough to create your own BLE applications. https://www.elektor.com/cdn/shop/files/develop-your-own-bluetooth-low-energy-applications.png?v=1689091056https://www.elektor.com/products/develop-your-own-bluetooth-low-energy-applications?variant=46907227111756 in stock 39.95 185 4.9 6.9 2 - 4 Werktage 46907227144524 Develop your own Bluetooth Low Energy Applications (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) > Raspberry Pi | Arduino | ESP has-digital-downloads,variant-46907227144524-has-digital-downloads 978-3-89576-501-8 For Raspberry Pi, ESP32 and nRF52 with Python, Arduino and Zephyr Bluetooth Low Energy (BLE) radio chips are ubiquitous from Raspberry Pi to light bulbs. BLE is an elaborate technology with a comprehensive specification, but the basics are quite accessible. A progressive and systematic approach will lead you far in mastering this wireless communication technique, which is essential for working in low power scenarios. In this book, you’ll learn how to: Discover BLE devices in the neighborhood by listening to their advertisements. Create your own BLE devices advertising data. Connect to BLE devices such as heart rate monitors and proximity reporters. Create secure connections to BLE devices with encryption and authentication. Understand BLE service and profile specifications and implement them. Reverse engineer a BLE device with a proprietary implementation and control it with your own software. Make your BLE devices use as little power as possible. This book shows you the ropes of BLE programming with Python and the Bleak library on a Raspberry Pi or PC, with C++ and NimBLE-Arduino on Espressif’s ESP32 development boards, and with C on one of the development boards supported by the Zephyr real-time operating system, such as Nordic Semiconductor's nRF52 boards. Starting with a very little amount of theory, you’ll develop code right from the beginning. After you’ve completed this book, you’ll know enough to create your own BLE applications. https://www.elektor.com/cdn/shop/files/develop-your-own-bluetooth-low-energy-applications-pdf.png?v=1689091063https://www.elektor.com/products/develop-your-own-bluetooth-low-energy-applications-e-book?variant=46907227144524 in stock 29.95 -1 4.9 6.9 2 - 4 Werktage 46907176517964 DFRobot Bluno - Arduino-compatible Board with Bluetooth 4.0 DFRobot Trade Arduino > Arduino Boards > Bestsellers > No Member Discount > Sale 019878 Bluno is the first of its kind in integrating Bluetooth 4.0 (BLE) module into Arduino Uno, making it an ideal prototyping platform for both software and hardware developers to go BLE. You will be able to develop your own smart bracelet, smart pedometer, and more. Through the low-power Bluetooth 4.0 technology, real-time low energy communication can be made really easy. Bluno integrates a TI CC2540 BT 4.0 chip with the Arduino UNno. It allows wireless programming via BLE, supports Bluetooth HID, AT command to config BLE and you can upgrade BLE firmware easily. Bluno is also compatible with all 'Arduino Uno' pins which means any project made with Uno can directly go wireless! Specifications On-board BLE chip: TI CC2540 Wireless Programming via BLE Support Bluetooth HID Support AT command to config the BLE Transparent communication through Serial Upgrade BLE firmware easily DC Supply: USB Powered or External 7~12 V DC Microcontroller: Atmega328 Bootloader: Arduino Uno ( disconnect any BLE device before uploading a new sketch ) Compatible with the Arduino Uno pin mapping Size: 60 x 53 mm(2.36 x 2.08') Weight: 30 g https://www.elektor.com/cdn/shop/files/dfrobot-bluno.jpg?v=1689089402https://www.elektor.com/products/dfrobot-bluno-arduino-compatible-board-with-bluetooth-4-0?variant=46907176517964 in stock 34.95 27.95 11 4.9 6.9 2 - 4 Werktage 46907086274892 DFRobot Gravity - Lightning Distance Sensor DFRobot Trade Bestsellers > Components > No Member Discount > Platforms > Robotics > Sale > Sensors & LiDAR SEN0290 The embedded man-made disturber rejection algorithm can effectively avoid the electrical interference generated by various household appliances. In addition to allowing general weather enthusiasts to measure local thunderstorm data simply and efficiently, thanks to its compact size and wide detection range, it can also be embedded in various smart wearable devices for an outdoor climber or people who work at heights.This provides early warning of thunderstorms that people can perceive so that people can take precautions a step ahead. The sensor can also be embedded in the indoor protection device inside lightning-sensitive equipment, and automatically trigger these devices to switch to the backup power to isolate the power grid when lightning strikes. At the moment of lightning, the interrupt pin IRQ generates a pulse. This can be used to trigger the shutter to open, helping photographers to accurately capture the exciting moment of lightning.The maximum estimated distance of lightning strike is 40km. Limited by the inherent measurement method and algorithm, the distance estimation resolution is 1~4km, 40 km in 15 steps.FeaturesLightning detection within 40km in 15 stepsLighting intensity detectionUsed both indoors or outdoorsEmbedded man-made disturber rejection algorithmApplicationsConsumer Weather Station (thunderstorm measurement)Wearable Devices (outdoor thunderstorm early warning)Lightning PhotographySpecificationInput Voltage : 3.3 V - 5.5 VMaximum Detection Range: 40 kmDistance Detection Resolution: 1 km - 4 kmIntensity Detection Resolution: 21 bits, i.e. 0 ~16777201I2C Address: Three options 0x03, 0x02, 0x01Interface: Gravity I2C (logic level: 0-VCC)Dimension: 30 mm x 22 mmFor more information, check out the DFRobot Gravity – Lightning Distance Sensor wiki page here. https://www.elektor.com/cdn/shop/files/dfrobot_gravity_lightning_distance_sensor.jpg?v=1689087099https://www.elektor.com/cdn/shop/files/dfrobot_gravity_lightning_distance_sensor_-_dimensions.jpg?v=1696850921https://www.elektor.com/products/dfrobot-gravity-lightning-distance-sensor?variant=46907086274892 in stock 29.95 24.95 3 4.9 6.9 2 - 4 Werktage 46907182809420 Diamex EXA-Prog Package Diamex Trade Bestsellers > Deals > Measuring Tools > No Member Discount > Programmers & Debuggers > Prototyping 4260352723958 EXA-Prog in housing EXA-Prog represents the new generation of ISP programmers, which are not limited to one specific microcontroller type, but support several different controller architectures and programming interfaces. Laser-cut plexiglass housing. Two built-in status LEDs signal the current state of the programmer. Features Function selection via DIP switch Signal level switchable, 3.3 V, 5 V Integrated high voltage generator for UPDI programming Automatic bit-rate adjustment in AVR-ISP mode Clock generator for AVR controller with fuse oscillator Button to reset the connected microcontroller 10-pin standard ISP connector Optional accessories: 10-pin to 6-pin adapter, ESP01 adapter Mini-USB connector for power supply and connection to PC Firmware can be updated via USB Windows PC tool for testing the signal levels at the programming port. Current consumption without microcontroller connected: approx. 30 mA Signal level at programming connector: 5 V (USB voltage) or 3.3 V Power supply for the external circuit: max. 300 mA (3.3 V), max. 500 mA (5 V) UPDI high voltage: approx. 12.3 V Weight: approx. 25 g Adapter 10-pin to 6-pin IS P and 6-pin UPDI The optimal solution for in-system programming (ISP) of AVR controllers. There are two different standards for the AVR-ISP interface, 6-pin and 10-pin. With this adapter kit, you can exchange the programming lines between both standards. For programming AVR-UPDI a 6-pin connector is also needed. This adapter supports 10-pin to 6-pin for AVR-ISP programming and 10-pin to 6-pin for AVR-UPDI programming. ESP adapter No buttons or switches are needed to activate the ESP bootloader. When ESPTOOL is used, the bootloader is automatically activated and the firmware is started after programming is complete. If another program is used that does not take over this control itself, the bootloader of the ESP can also be activated by a long press on the RESET button of the EXA-PROG and the firmware can be started by a short press after programming. AVR swivel lever High-quality module with swivel lever zero force socket for almost all AVR controllers in DIL package. No own board is required. DIL controllers are easy and fast to program. Can also be used for series production. The 10-pin ISP standard connector from Atmel is used. Additionally, pin 3 is designed as a clock connector if the controller is set to an external clock. 5x 10-pin ISP well connectors for AVR controller in DIL package Compatible with all signal levels Pin 3 for the clock generator High quality swing lever socket (zero force socket) for variable 4-18 mm pin spacing Included EXA-Prog in housing Adapter 10-pin to 6-pin ISP and 6-pin UPDI ESP adapter AVR swivel lever Mini-USB cable 10-pin connection cable 6-pin connection cable 6-pin jumper cable, male-female 6-pin jumper cable, female-female https://www.elektor.com/cdn/shop/files/diamex_exa-prog_package_-_overview.jpg?v=1689089552https://www.elektor.com/cdn/shop/files/exa-prog_in_housing.jpg?v=1696852570,https://www.elektor.com/cdn/shop/files/exa-prog_in_housing_-_cable.jpg?v=1696852570,https://www.elektor.com/cdn/shop/files/adapter_10pin_to_6pin_isp_and_6pin_updi_-_overview.jpg?v=1696852570,https://www.elektor.com/cdn/shop/files/adapter_10pin_to_6pin_isp_and_6pin_updi_-_with_cable.jpg?v=1696852570,https://www.elektor.com/cdn/shop/files/esp_adapter.jpg?v=1698678952,https://www.elektor.com/cdn/shop/files/avr_swivel_lever.jpg?v=1698678952https://www.elektor.com/products/diamex-exa-prog-package?variant=46907182809420 in stock 74.95 64.95 7 0 6.9 2 - 4 Werktage 46907182547276 Diamex LED Player M Diamex Trade Components > Displays & LEDs 4260352721039 Up to 2048 digital PWM LEDs can be comfortably managed and easily controlled by the Diamex LED Player M. Equipped with eight channels, small and even larger projects for party lighting, video boards or professional lighting installations can be implemented quickly. Live videos on a panel surface are possible as well as stored sequences, light moods or effect installations for small and large lighting performances. Applications such as party lighting, home cinema installations, pool lighting, garden and home lighting, moving stores or sophisticated LED lighting solutions indoors or outdoors - all no longer a problem. With the Diamex LED Player M the imagination has no limits. At the same time, the module is small, compact and highly configurable. Via USB, Windows pads or notebooks and PCs can be used as feed players. Free software like JINX! or gLEDiator are perfectly suited for home and professional applications. These sequences can also be stored as a file on a simple mini-SD card and inserted into the Diamex LED Player M, turning the module into a stand-alone light jockey. Simply put, it's a real powerhouse equipped with state-of-the-art Cortex M4 microcontroller technology, a real highlight for professionals and amateurs alike, which can handle a wide variety of strips and matrices and is also future-proof via online firmware update. Specifications LED panel programs like JINX or GLEDIATOR can send their data directly to the Diamex LED Player M via the USB port. Maximum capacity: 512 LEDs per channel, 2048 LEDs in total. Different LED protocols are supported, both for LEDs with only one asynchronous data line (single wire) and LEDs with synchronous DATA and TAKT lines (dual wire). LEDs, Stripes, Panels of the following types are supported: WS2811/12 (compatible UCS1903, PL9823), APA106, WS2821 (DMX), WS2801, APA102, LPD8803/06. Mini-USB 2.0 port for virtual COM port (player for JINX, GLEDIATOR etc.), configuration and updates via bootloader. 2 buttons for sequence control. Screw terminals for LED data outputs and power supply. Fully configurable via PC-Tool: Protocol for PC data, LED protocol, number of connected strips or panels, arrangement of colours in the data stream, length of strips, size of panels and arrangement of LEDs on panels, mirroring, timing parameters of protocols. MicroSD card slot for playing files in TPM2 format even without a PC. SD cards can be read and written directly from a PC as a virtual drive. Status LEDs for system and SD card. Controlled by powerful 32-bit Cortex-M4 microcontroller Board size: 71 x 31mm https://www.elektor.com/cdn/shop/files/diamex_led_player_m_-_overview.jpg?v=1689089544https://www.elektor.com/cdn/shop/files/diamex_led_player_m_-_configuration.jpg?v=1696852560https://www.elektor.com/products/diamex-led-player-m?variant=46907182547276 in stock 54.95 1 0 6.9 2 - 4 Werktage 46907182481740 Diamex LED Tube Clock ESP Kit Diamex Trade Bestsellers > Components > Displays & LEDs > Kits 4260352723965 The Diamex LED Tube Clock ESP Kit has a WLAN interface, with which the current highly accurate time can be retrieved directly from the Internet via the home router. In addition, a battery-buffered real-time clock is built in, which takes over when no WLAN is available. The WLAN access data are configured via the LED-Basic development environment (from version 15.3.0). The Diamex LED Tube Clock ESP Kit can be operated worldwide, the time zone can be chosen arbitrarily. The winter/summer time changeover is done automatically. Specifications 8-digit, bright 7-segment display Real-time clock including mounting bracket for a CR2012 battery Time setting via PC, WLAN or directly at the clock 4 buttons Beeper (sound output) Micro USB port for power supply, basic data, bios update and terminal output Board size: approx. 130 x 75 mm https://www.elektor.com/cdn/shop/files/diamex_led_tube_clock_esp_kit_-_overview.jpg?v=1689089537https://www.elektor.com/cdn/shop/files/diamex_led_tube_clock_esp_kit_-_assembled.jpg?v=1696852553,https://www.elektor.com/cdn/shop/files/diamex_led_tube_clock_esp_kit_-_disassembled.jpg?v=1696852553https://www.elektor.com/products/diamex-led-tube-clock-esp-kit?variant=46907182481740 in stock 54.95 2 0 6.9 2 - 4 Werktage 46907297431884 Digital Desoldering Station ZD-915 Zhongdi Boards&Kits Comparison Websites DE > Comparison Websites FR > Elektor Labs Selection > Measuring Tools > No Member Discount > Platforms > Prototyping > Soldering Stations Comparison Websites 020142 The ZD-915 is a digital desoldering station with ESD protection and digital display of both the actual and set value on an LCD screen. This desoldering station has high power in a compact and robust housing and makes desoldering easy, because it can be operated with one hand. The ZD-915 features a soldering gun that houses a filter that catches any sucked material, so you only need to replace the filters to continue. There is also a temperature sensor in the tip so that temperature fluctuations can be quickly absorbed. Features The temperature is easily adjusted by simple up/down buttons. 140 W temperature controlled soldering station with adjustable range from 160 °C to 480 °C. The desoldering station is designed for lead free desoldering specially. The side of the station features a typical holder with sponge. An illuminated power on/off is also loacted on the front. Specifications Station Voltage supply 220-240 V Power consumption 140 W Vakuum pressure 600 mm HG Desoldering Gun Power consumption 24 V AC 80 WHeat up rating 130 W Temperature 160-480 °C Heating element Ceramic heater Included 1x Desoldering station ZD-915 2x Spare soldering tip 3x Cleaning needle for desoldering tips 1x Spare filter for desoldering gun 1x Manual https://www.elektor.com/cdn/shop/files/zd-915-desoldering-rework-station_selected.jpg?v=1689093466https://www.elektor.com/cdn/shop/files/zd-915-desoldering-rework-station_unit_1.jpg?v=1696855333,https://www.elektor.com/cdn/shop/files/zd-915-desoldering-rework-station_gun.jpg?v=1696855333https://www.elektor.com/products/digital-desoldering-station-zd-915?variant=46907297431884 out of stock 119.95 99.95 -1 0 6.9 nicht auf Lager 46907196506444 DiP-Pi Pico PIoT for Raspberry Pi Pico Elektor Trade Bestsellers > No Member Discount > Pico RP2040 > Raspberry Pi > Sale 019987 The DiP-Pi PIoT is an Advanced Powered, WiFi connectivity System with sensors embedded interfaces that cover most of possible needs for IoT application based on Raspberry Pi Pico. It can supply the system with up to 1.5 A @ 4.8 V delivered from 6-18 VDC on various powering schemes like Cars, Industrial plant etc., additionally to original micro-USB of the Raspberry Pi Pico. It supports LiPo or Li-Ion Battery with Automatic Charger as also automatic switching from cable powering to battery powering or reverse (UPS functionality) when cable powering lost. Extended Powering Source (EPR) is protected with PPTC Resettable fuse, Reverse Polarity, as also ESD.The DiP-Pi PIoT contains Raspberry Pi Pico embedded RESET button as also ON/OFF Slide Switch that is acting on all powering sources (USB, EPR or Battery). User can monitor (via Raspberry Pi Pico A/D pins) battery level and EPR Level with PICO’s A/D converters. Both A/D inputs are bridged with 0402 resistors (0 OHM) therefore if for any reason user needs to use those Pico pins for their own application can be easy removed. The charger is automatically charging connected battery (if used) but in addition user can switch charger ON/OFF if their application needs it.DiP-Pi PIoT can be used for cable powered IoT systems, but also for pure Battery Powered System with ON/OFF. Each powering source status is indicated by separate informative LEDs (VBUS, VSYS, VEPR, CHGR, V3V3).User can use any capacity of LiPo or Li-Ion type; however, must take care to use PCB protected batteries with max discharge current allowed of 2 A. The embedded battery charger is set to charge battery with 240 mA current. This current is set by resistor so if user need more/less can himself to change it. The DiP-Pi PIoT is also equipped with WiFi ESP8266 Clone module with embedded antenna. This feature open a wide range of IoT applications based on it.In Addition to all above features DiP-Pi PIoT is equipped with embedded 1-wire, DHT11/22 sensors, and micro–SD Card interfaces. Combination of the extended powering, battery, and sensors interfaces make the DiP-Pi PIoT ideal for IoT applications like data logger, plants monitoring, refrigerators monitoring etc.DiP-Pi PIoT is supported with plenty of ready to use examples written in Micro Python or C/C++.SpecificationsGeneralDimensions 21 x 51 mmRaspberry Pi Pico pinout compatibleIndependent Informative LEDs (VBUS, VSYS, VEPR, CHGR, V3V3)Raspberry Pi Pico RESET ButtonON/OFF Slide Switch acting on all powering sources (USB, EPR, Battery)External Powering 6-18 VDC (Cars, Industrial Applications etc.)External Power (6-18 VDC) Level MonitoringBattery Level MonitoringInverse Polarity ProtectionPPTC Fuse ProtectionESD ProtectionAutomatic Battery Charger (for PCB protected LiPo, Li-Ion – 2 A Max) Automatic/User ControlAutomatic Switch from Cable Powering to Battery Powering and reverse (UPS Functionality)Various powering schemes can be used at the same time with USB Powering, External Powering and Battery Powering1.5 A @ 4.8 V Buck Converter on EPREmbedded 3.3 V @ 600 mA LDOESP8266 Clone WiFi ConnectivityESP8266 Firmware Upload SwitchEmbedded 1-wire InterfaceEmbedded DHT-11/22 InterfacePowering OptionsRaspberry Pi Pico micro-USB (via VBUS)External Powering 6-18 V (via dedicated Socket – 3.4/1.3 mm)External Battery Supported Battery TypesLiPo with protection PCB max current 2ALi-Ion with protection PCB max current 2A Embedded Peripherals and InterfacesEmbedded 1-wire interfaceEmbedded DHT-11/22 InterfaceMicro SD Card SocketProgrammer InterfaceStandard Raspberry Pi Pico C/C++Standard Raspberry Pi Pico Micro PythonCase CompatibilityDiP-Pi Plexi-Cut CaseSystem MonitoringBattery Level via Raspberry Pi Pico ADC0 (GP26)EPR Level via Raspberry Pi Pico ADC1 (GP27)Informative LEDsVB (VUSB)VS (VSYS)VE (VEPR)CH (VCHR)V3 (V3V3)System ProtectionDirect Raspberry Pi Pico Hardware Reset ButtonESD Protection on EPRReverse Polarity Protection on EPRPPTC 500 mA @ 18 V fuse on EPREPR/LDO Over... https://www.elektor.com/cdn/shop/files/dip-pi-pico-piot-for-raspberry-pi-pico.jpg?v=1689089964https://www.elektor.com/cdn/shop/files/dip-pi-pico-piot-for-raspberry-pi-pico_back.jpg?v=1696852859,https://www.elektor.com/cdn/shop/files/dip-pi-pico-piot-for-raspberry-pi-pico_connected.jpg?v=1696852859https://www.elektor.com/products/dip-pi-pico-piot-for-raspberry-pi-pico?variant=46907196506444 in stock 21.95 17.95 25 4.9 6.9 2 - 4 Werktage 46907196899660 DiP-Pi Pico Power Master for Raspberry Pi Pico Elektor Trade Bestsellers > No Member Discount > Pico RP2040 > Raspberry Pi > Sale 019988 The DiP-Pi Power Master is an Advanced Powering System with embedded sensors interfaces that cover most of possible needs for application based on Raspberry Pi Pico. It can supply the system with up to 1.5 A @ 4.8 V delivered from 6-18 VDC on various powering schemes like Cars, Industrial plant etc., additionally to original micro-USB of the Raspberry Pi Pico. It supports LiPo or Li-Ion Battery with Automatic Charger as also automatic switching from cable powering to battery powering or reverse (UPS functionality) when cable powering lost. Extended Powering Source (EPR) is protected with PPTC Resettable fuse, Reverse Polarity, as also ESD.The DiP-Pi Power Master contains Raspberry Pi Pico embedded RESET button as also ON/OFF Slide Switch that is acting on all powering sources (USB, EPR or Battery). User can monitor (via Raspberry Pi Pico A/D pins) battery level and EPR Level with PICO’s A/D converters. Both A/D inputs are bridged with 0402 resistors (0 OHM) therefore if for any reason user needs to use those Pico pins for their own application can be easy removed. The charger is automatically charging connected battery (if used) but in addition user can switch charger ON/OFF if their application needs it. DiP-Pi Power Master can be used for cable powered systems, but also for pure Battery Powered System with ON/OFF. Each powering source status is indicated by separate informative LEDs (VBUS, VSYS, VEPR, CHGR, V3V3).User can use any capacity of LiPo or Li-Ion type; however, must take care to use PCB protected batteries with max discharge current allowed of 2 A. The embedded battery charger is set to charge battery with 240 mA current. This current is set by resistor so if user need more/less can himself to change it.In Addition to all above features DiP-Pi Power Master is equipped with embedded 1-wire and DHT11/22 sensors interfaces. Combination of the extended powering, battery, and sensors interfaces make the DiP-Pi Power Master ideal for applications like data logger, plants monitoring, refrigerators monitoring etc.DiP-Pi Power Master is supported with plenty of ready to use examples written in Micro Python or C/C++.SpecificationsGeneralDimensions 21 x 51 mmRaspberry Pi Pico pinout compatibleIndependent Informative LEDs (VBUS, VSYS, VEPR, CHGR, V3V3)Raspberry Pi Pico RESET ButtonON/OFF Slide Switch acting on all powering sources (USB, EPR, Battery)External Powering 6-18 V DC (Cars, Industrial Applications etc.)External Power (6-18 VDC) Level MonitoringBattery Level MonitoringInverse Polarity ProtectionPPTC Fuse ProtectionESD ProtectionAutomatic Battery Charger (for PCB protected LiPo, Li-Ion – 2 A Max) Automatic/User ControlAutomatic Switch from Cable Powering to Battery Powering and reverse (UPS Functionality)Various powering schemes can be used at the same time with USB Powering, External Powering and Battery Powering1.5 A @ 4.8 V Buck Converter on EPREmbedded 3.3 V @ 600mA LDOEmbedded 1-wire InterfaceEmbedded DHT-11/22 InterfacePowering OptionsRaspberry Pi Pico micro-USB (via VBUS)External Powering 6-18 V (via dedicated Socket – 3.4/1.3 mm)External Battery Supported Battery TypesLiPo with protection PCB max current 2ALi-Ion with protection PCB max current 2A Embedded Peripherals and InterfacesEmbedded 1-wire interfaceEmbedded DHT-11/22 InterfaceProgrammer InterfaceStandard Raspberry Pi Pico C/C++Standard Raspberry Pi Pico Micro PythonCase CompatibilityDiP-Pi Plexi-Cut CaseSystem MonitoringBattery Level via Raspberry Pi Pico ADC0 (GP26)EPR Level via Raspberry Pi Pico ADC1 (GP27)Informative LEDsVB (VUSB)VS (VSYS)VE (VEPR)CH (VCHR)V3 (V3V3)System ProtectionDirect Raspberry Pi Pico Hardware Reset ButtonESD Protection on EPRReverse Polarity Protection on EPRPPTC 500 mA @ 18 V fuse on EPREPR/LDO Over Temperature protectionEPR/LDO Over Current protectionSystem DesignDesigned and Simulated with PDA Analyzer with one of the most advanced CAD/CAM Tools – Altium DesignerIndustrial OriginatedPCB Construction2 ozcopper PCB manufact... https://www.elektor.com/cdn/shop/files/dip-pi-pico-power-master-for-raspberry-pi-pico.jpg?v=1689089971https://www.elektor.com/cdn/shop/files/dip-pi-pico-power-master-for-raspberry-pi-pico_back.jpg?v=1696852867,https://www.elektor.com/cdn/shop/files/dip-pi-pico-power-master-for-raspberry-pi-pico_connected.jpg?v=1696852867https://www.elektor.com/products/dip-pi-pico-power-master-for-raspberry-pi-pico?variant=46907196899660 in stock 17.95 14.95 40 4.9 6.9 2 - 4 Werktage 46907196965196 DiP-Pi Pico WiFi Master for Raspberry Pi Pico Elektor Trade Bestsellers > No Member Discount > Pico RP2040 > Raspberry Pi > Sale 019989 The DiP-Pi WiFi Master is an Advanced WiFi connectivity System with sensors embedded interfaces that cover most of possible needs for IoT application based on Raspberry Pi Pico. It is powered directly from the Raspberry Pi Pico VBUS. The DiP-Pi WiFi Master contains Raspberry Pi Pico embedded RESET button as also ON/OFF Slide Switch that is acting on Raspberry Pi Pico Power Sources. The DiP-Pi WiFi Master is equipped with WiFi ESP8266 Clone module with embedded antenna. This feature open a wide range of IoT applications based on it. In Addition to all above features DiP-Pi WiFi Master is equipped with embedded 1-wire, DHT11/22 sensors, and micro–SD Card interfaces. Combination of the extended powering, battery, and sensors interfaces make the DiP-Pi WiFi Master ideal for IoT applications like data logger, plants monitoring, refrigerators monitoring etc. DiP-Pi WiFi Master is supported with plenty of ready to use examples written in Micro Python or C/C++. Specifications General Dimensions 21 x 51 mm Raspberry Pi Pico pinout compatible Independent Informative LEDs (VBUS, VSYS, V3V3) Raspberry Pi Pico RESET Button ON/OFF Slide Switch acting on Raspberry Pi Pico Powering Source Embedded 3.3 V @ 600 mA LDO ESP8266 Clone WiFi Connectivity ESP8266 Firmware Upload Switch Embedded 1-wire Interface Embedded DHT-11/22 Interface Powering Options Raspberry Pi Pico micro-USB (via VBUS) Embedded Peripherals and Interfaces Embedded 1-wire interface Embedded DHT-11/22 Interface Micro SD Card Socket Programmer Interface Standard Raspberry Pi Pico C/C++ Standard Raspberry Pi Pico Micro Python Case Compatibility DiP-Pi Plexi-Cut Case Informative LEDs VB (VUSB) VS (VSYS) V3 (V3V3) System Protection Direct Raspberry Pi Pico Hardware Reset Button PPTC 500 mA @ 18 V fuse on EPR EPR/LDO Over Temperature protection EPR/LDO Over Current protection System Design Designed and Simulated with PDA Analyzer with one of the most advanced CAD/CAM Tools – Altium Designer Industrial Originated PCB Construction 2 ozcopper PCB manufactured for proper high current supply and cooling 6 mils track/6 mils gap technology 2 layers PCB PCB Surface Finishing – Immersion Gold Multi-layer Copper Thermal Pipes for increased System Thermal Response and better passive cooling Downloads Datasheet Manual https://www.elektor.com/cdn/shop/files/dip-pi-pico-wifi-master-for-raspberry-pi-pico.jpg?v=1689089978https://www.elektor.com/cdn/shop/files/dip-pi-pico-wifi-master-for-raspberry-pi-pico_back.jpg?v=1696852873https://www.elektor.com/products/dip-pi-pico-wifi-master-for-raspberry-pi-pico?variant=46907196965196 in stock 19.95 13.95 49 4.9 6.9 2 - 4 Werktage 46907118420300 DIY LiPo Supercharger Kit V2 (by GreatScott!) Elektor Labs Boards&Kits Bestsellers > Components > Elektor Kits > Elektor Products > Kits > No Member Discount > Sale 7442105129188 This DIY LiPo Supercharger/Booster (developed the electronics engineer/YouTuber GreatScott! and produced by Elektor) can charge a single-cell LiPo battery and protect it against the effects of overvoltage, overload, and short-circuits. Additionally, it can boost the battery voltage to 5 V or 12 V. The boosted output voltage is protected by an ‘eFuse’ IC outputting 1.52 A at 5 V or 0.76 A at 12 V maximum.The charger part of the circuit needs a +5 V power supply which can be connected through USB-C, or simply two wires soldered to pads on the PCB.In addition, other connections can be soldered to pads on the PCB or by using single pinheaders.Included1x Mainboard pre-assembled with the 4 ICs15x Resistors3x LEDs13x Capacitors2x Switches1x USB-C on a breakout board2x DiodesPlease note: Battery is not included.The board uses a DC/DC Converter, an IC charger, and an e Fuse from Texas Instruments. The battery protection IC is from Xysemi and provides under-voltage lockout, over current protection, and reverse battery protection.The board is connected to the power and recharges the batteries via a USB-C connection.SpecificationsBatterySingle-cell lithium-ion or lithium-polymer batteryInput Voltage+5 V / 2 A max.Output Voltage5 V / 1.52 A12 V / 0.76 ALiPo ProtectionXB8089DOvercharge Detection4.250 VOvercharge Release4.10 VOverdischarge Detection2.50 VOverdischarge Release3 VOvercurrent Detection10.0 AThermal ShutdownAuto-retryEnable/Undervoltage LockoutRising: 1.2 V (typ.)Falling: 1.1 V (typ.) https://www.elektor.com/cdn/shop/files/diy-lipo-supercharger-kit-by-greatscott.png?v=1689087711https://www.elektor.com/cdn/shop/files/diy-lipo-supercharger-kit_mainboard.png?v=1696851258https://www.elektor.com/products/diy-lipo-supercharger-kit-v2-by-greatscott?variant=46907118420300 in stock 29.95 24.95 78 4.9 6.9 2 - 4 Werktage 46907147321676 DIYIC Proto Board Kit Evil Mad Science Trade Bestsellers > Components > Kits 019734 The matte-black circuit board is extra thick and has subtle white markings, including an alphanumeric grid and PIN labels. The wiring pattern — that of classic breadboards — is easy to see by looking at the exposed traces on the bottom of the board.The kit comes complete with the 'Integrated Circuit Leg' stand and 8 colour-coded thumbscrew terminal posts. Using the terminal posts and solder points, you can hook up to your 'IC' with bare wires, lugs, alligator clips, and/or solder joints. Connections to the 8 terminal posts are through the three-position strips on the PCB; each is labelled with the corresponding PIN.FeaturesAnodized aluminium stand8-32 size press-fit threaded inserts (8 pieces) pre-installed in the protoboardAll materials (including the circuit board and stand) are RoHS compliant (lead-free)Tri lobular thread forming screws (6 pieces, black, 6-32 thread size) and spacers for mounting the stand.Dimensions: 13.25 cm × 8.06 cm x 2.54 mmDimensions assembled: 13.25 cm × 9.9 cm × 4.3 cm https://www.elektor.com/cdn/shop/files/diyic_proto_board_kit.jpg?v=1689088652https://www.elektor.com/cdn/shop/files/diyic_proto_board_kit_-_top_view.jpg?v=1696851950,https://www.elektor.com/cdn/shop/files/diyic_proto_board_kit_-_parts.jpg?v=1696851950https://www.elektor.com/products/diyic-proto-board-kit?variant=46907147321676 in stock 34.95 28 4.9 6.9 2 - 4 Werktage 46907091288396 Dragino DLOS8 Outdoor LoRaWAN Gateway (EU868) Dragino Trade Bestsellers > IoT & LoRa > Platforms 019389 The DLOS8 is an open-source outdoor LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via Ethernet, WiFi or 3G. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates. The DLOS8 uses Semtech packet forwarder and fully compatible with LoRaWAN protocol. It includes an SX1301 LoRaWAN concentrator, which provides ten programmable parallel demodulation paths. DLOS8 has pre-configured standard LoRaWAN frequency bands to use for different countries. User can also customize the frequency bands to use in their LoRaWAN network. DLOS8 can communicate with ABP LoRaWAN end node without LoRaWAN server. The system integrator can use it to integrate with their existing IoT Service without set up own LoRaWAN server or use 3rd party LoRaWAN service. Features Managed by SSH via LAN or WiFi, Web GUI Open Source OpenWrt system Emulates 49x LoRa demodulators Outdoor LoRaWAN Gateway LoRaWAN packet filtering Ten programmable parallel demodulation paths Farseeing LED indicator External fibreglass antenna Built-in GPS module for location & timing 802.3af PoE IP65 Lighting Protection Power Consumption:12 V, 300 mA ~ 500 mA 1x 10M / 100M RJ45 Ports 1x USB host port 2.4G WiFi (802.11 bgn) Applications Logistics and Supply Chain Management Smart Buildings & Home Automation Smart Metering Smart Cities Smart Agriculture Smart Factory Downloads Datasheet User Manual Firmware Mechanical https://www.elektor.com/cdn/shop/files/dragino_dlos8_outdoor_lorawan_gateway_-_parts.jpg?v=1689087350https://www.elektor.com/cdn/shop/files/dragino_dlos8_outdoor_lorawan_gateway.jpg?v=1696851100,https://www.elektor.com/cdn/shop/files/dragino_dlos8_outdoor_lorawan_gateway_-_assembled.jpg?v=1696851100https://www.elektor.com/products/dragino-dlos8-outdoor-lorawan-gateway-eu868?variant=46907091288396 in stock 399.0 11 0 0 2 - 4 Werktage 46907198079308 Dragino LDS02 LoRaWAN Door Sensor (EU868) Dragino Trade Bestsellers > Components > IoT & LoRa > Platforms > Sensors & LiDAR 020004 The LDS02 is powered by 2x AAA batteries and targets long-time use, these two batteries can provide about 16,000 ~ 70,000 uplink packets. After the batteries run out, the user can easily open the enclosure and replace them with 2 common AAA batteries. It will send periodically data every day as well as for each door open/close action. It also counts the door open times and calculates the last door open duration. The user can also disable the uplink for each open/close event, instead, the device can count each open event and uplink periodically. It also has the open alarm feature, the user can set this feature so the device will send an alarm if the door has been open for a certain time. Each LDS02 is pre-load with a set of unique keys for LoRaWAN registration, register these keys to the LoRaWAN server and it will auto-connect after power on. Features LoRaWAN v1.0.3 Class A SX1262 LoRa Core Door Open/Close detect 2 x AAA LR03 Batteries Door open/close statistics AT Commands to change parameters Uplink on periodically and open/close action Open duration alarm Downlink to change configure Applications Wireless Alarm and Security Systems Home and Building Automation Industrial Monitoring and Control https://www.elektor.com/cdn/shop/files/dragino_lds02_-_overview.jpg?v=1689090023https://www.elektor.com/cdn/shop/files/dragino_lds02_-_top_view.jpg?v=1696852910https://www.elektor.com/products/dragino-lds02-lorawan-door-sensor-eu868?variant=46907198079308 in stock 34.95 42 4.9 6.9 2 - 4 Werktage 47613924639052 Dragino LoRa/LoRaWAN IoT Kit v3 (EU868) Dragino Trade Bestsellers > IoT & LoRa > Kits > NEW > Platforms 6973956307421 Dragino LoRaWAN IoT Kit v3 is designed to facilitate beginners and developers to quickly learn and demonstrate LoRa/LoRaWAN and IoT technology. It helps users to turn the idea into a practical application and make the Internet of Things a reality. The LoRaWAN IoT Kit v3 can be used to evaluate the multi-channel LoRaWAN solution and single-channel private LoRa solution. Users can also use LoRaWAN IoT Kit v3 to test different network structure solutions and find the best for their IoT solution. The LoRaWAN IoT kit v3 shows how to build a LoRaWAN network, and how to use the network to send data from a LoRa sensor node to the cloud server. Depends on the actually use environment, the LoRaWAN gateway will connect your other LoRa nodes up to 500~5000 m. Features Open Source LoRa/LoRaWAN kits Support multi-channels LoRaWAN and Single-Channel LoRa Support various network structures Included 1x LPS8v2 LoRaWAN Gateway 1x LA66 LoRaWAN Shield for Arduino 1x LA66 USB LoRaWAN Adapter for PC/Mobile/RPi 1x DHT11 Temperature & Humidity Sensor 1x RGB LED 20x dupont cable (male to male) 20x dupont cable (female to female) 20x dupont cable (male to female) Downloads Datasheet Manual https://www.elektor.com/cdn/shop/files/Dragino-LoRa-LoRaWAN-IoT-Kit-v3.jpg?v=1710766116https://www.elektor.com/cdn/shop/files/Dragino-LoRa-LoRaWAN-IoT-Kit-v3_package.jpg?v=1710766121https://www.elektor.com/products/dragino-lora-lorawan-iot-kit-v3-eu868?variant=47613924639052 in stock 249.0 17 0 0 2 - 4 Werktage 47613925130572 Dragino LoRa/LoRaWAN IoT Kit v3 with 4G (EU868) Dragino Trade Bestsellers > IoT & LoRa > Kits > NEW > Platforms 6973956307438 Dragino LoRaWAN IoT Kit v3 is designed to facilitate beginners and developers to quickly learn and demonstrate LoRa/LoRaWAN and IoT technology. It helps users to turn the idea into a practical application and make the Internet of Things a reality. The LoRaWAN IoT Kit v3 can be used to evaluate the multi-channel LoRaWAN solution and single-channel private LoRa solution. Users can also use LoRaWAN IoT Kit v3 to test different network structure solutions and find the best for their IoT solution. The LoRaWAN IoT kit v3 shows how to build a LoRaWAN network, and how to use the network to send data from a LoRa sensor node to the cloud server. Depends on the actually use environment, the LoRaWAN gateway will connect your other LoRa nodes up to 500~5000 m. Features Open Source LoRa/LoRaWAN kits Support multi-channels LoRaWAN and Single-Channel LoRa Support various network structures Included 1x LPS8v2 LoRaWAN Gateway 1x LA66 LoRaWAN Shield for Arduino 1x LA66 USB LoRaWAN Adapter for PC/Mobile/RPi 1x DHT11 Temperature & Humidity Sensor 1x RGB LED 20x dupont cable (male to male) 20x dupont cable (female to female) 20x dupont cable (male to female) Downloads Datasheet Manual https://www.elektor.com/cdn/shop/files/DraginoLoRa-LoRaWANIoTKitv3with4G.jpg?v=1710767483https://www.elektor.com/cdn/shop/files/DraginoLoRa-LoRaWANIoTKitv3with4G_package.jpg?v=1710767494https://www.elektor.com/products/dragino-lora-lorawan-iot-kit-v3-with-4g-eu868?variant=47613925130572 in stock 299.0 18 0 0 2 - 4 Werktage 46907278786892 Dragino LPS8 Indoor LoRaWAN Gateway (EU868) Dragino Trade Bestsellers > Comparison Websites DE > Comparison Websites FR > IoT & LoRa > Platforms Comparison Websites 019094 The LPS8 is an open source multi-channel LoRaWAN Gateway. It lets you bridge LoRa wireless network to an IP network via WiFi or Ethernet. The LoRa wireless allows users to send data and reach extremely long ranges at low data-rates. The LPS8 uses Semtech Packet Forwarder and is fully compatible with the LoRaWAN protocol. It includes a SX1308 LoRa concentrator, which provides 10 programmable parallel demodulation paths. LPS8 has pre-configured standard LoRaWAN frequency bands to use for different countries. User can also customized the frequency bands to use in their own LoRa network. Features Linux-based OpenWrt system Managed by intuitive Web GUI, SSH via LAN of WiFi Remote access with Reverse-SSH Emulates 49x LoRa demodulators LoRaWAN Gateway 10 programmable parallel demodulation paths Applications Logistiek and Supply Chain Management Smart Buildings & Home Automation Smart Cities Smart Agriculture Smart Factory Smart Metering Specifications Power Input via USB Type-C (5 V, 2 A) 1x USB host port 1x RJ45 (10/100 Mbit/s) 1x 2.4 GHz WiFi (802.11 b/g/n) LoRa Specs: 1x SX1308 Lora Concentrator 2x 1257 LoRa Transceiver Downloads Datasheet User Manual Source code on GitHub Dragino LoRa Gateway Selection Guide Use Dragino LPS8 as Helium Data-Only Hotspot Dragino LoRaWAN Gateway Setup Dragino Gateways/Hotspots with Helium Tutorial Firmware https://www.elektor.com/cdn/shop/files/dragino_lps8_indoor_lorawan_gateway_-_overview.jpg?v=1689093000https://www.elektor.com/cdn/shop/files/dragino_lps8_indoor_lorawan_gateway_-_front_panel.jpg?v=1696854884https://www.elektor.com/products/dragino-lps8-indoor-lorawan-gateway-eu868?variant=46907278786892 in stock 199.95 9 0 0 2 - 4 Werktage 46907197981004 Dragino LSN50 Waterproof Long Range Wireless LoRa Sensor Node (EU868) Dragino Trade Bestsellers > Components > IoT & LoRa > Platforms > Sensors & LiDAR 020002 The LSN50 wireless part is based on SX1276/SX1278 allows the user to send data and reach extremely long ranges at low data rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation, and so on. The LSN50 MCU part uses STM32l0x chip from ST, STML0x is the ultra-low-power STM32L072xx microcontrollers incorporate the connectivity power of the universal serial bus (USB 2.0 crystal-less) with the high-performance ARM® Cortex®-M0+ 32-bit RISC core operating at a 32 MHz frequency, a memory protection unit (MPU), high-speed embedded memories (192 Kbytes of Flash program memory, 6 Kbytes of data EEPROM and 20 Kbytes of RAM) plus an extensive range of enhanced I/Os and peripherals. The LSN50 is an open-source product, it is based on the STM32Cube HAL drivers and lots of libraries can be found on the STM site for rapid development. Features STM32L072CZT6 MCU SX1276/78 LoRa Wireless Modem Pre-load with ISP bootloader I2C,LPUSART1,USB 18 x Digital I/Os 2 x 12bit ADC; 1 x 12bit DAC MCU wakes up by UART or Interrupt LoRa™ Modem Preamble detection Baud rate configurable LoRaWAN 1.0.2 Specification Software base on STM32Cube HAL drivers Open-source hardware / software IP66 Waterproof Enclosure Ultra-Low power consumption AT Commands to setup parameters 4000mAh Battery for Long term use Applications Wireless Alarm and Security Systems Home and Building Automation Automated Meter Reading Industrial Monitoring and Control Long-range Irrigation Systems LoRa Spec 168 dB maximum link budget. +20 dBm - 100 mW constant RF output vs. +14 dBm high-efficiency PA. Programmable bit rate up to 300 kbps. High sensitivity: down to -148 dBm. Bullet-proof front end: IIP3 = -12.5 dBm. Excellent blocking immunity. Low RX current of 10.3 mA, 200 nA register retention. Fully integrated synthesizer with a resolution of 61 Hz. FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation. Built-in bit synchronizer for clock recovery. Preamble detection. 127 dB Dynamic Range RSSI. Automatic RF Sense and CAD with ultra-fast AFC. Packet engine up to 256 bytes with CRC. Built-in temperature sensor and low battery indicator. MCU Spec MCU: STM32L072CZT6 Flash: 192KB SRAM: 20KB EEPROM: 6KB Clock Speed: 32Mhz Absolute Maximum Ratings VCC: 0.5 V ~ 3.9 V Operating Tempature: -40°C ~ 85°C I/O pins: 0.5 V ~ VCC+0.5 V Common DC Characteristics Supply Voltage: 1.8 V ~ 3.6 V Operating Tempature: -40°C ~ 85°C I/O pins: STM32L072CZT6 datasheet Power Consumption STOP Mode: 2.7 μA @ 3.3 V RX Mode: 7.2 mA TX Mode: 125 mA@ 20 dbm Battery Li/SOCI2 unchargable battery Capacity: 4000 mAh Self Discharge: < 1% / Year @ 25°C Max continuously current: 130 mA Max boost current: 2 A, 1 second https://www.elektor.com/cdn/shop/files/dragino_lsn50_-_overview.jpg?v=1689090016https://www.elektor.com/cdn/shop/files/dragino_lsn50_-_assembled.jpg?v=1696852903,https://www.elektor.com/cdn/shop/files/dragino_lsn50_-_in_case.jpg?v=1696852903,https://www.elektor.com/cdn/shop/files/dragino_lsn50_-_top_view.jpg?v=1696852903,https://www.elektor.com/cdn/shop/files/dragino_lsn50_-_closed.jpg?v=1696852904https://www.elektor.com/products/dragino-lsn50-waterproof-long-range-wireless-lora-sensor-node-eu868?variant=46907197981004 in stock 54.95 13 0 6.9 2 - 4 Werktage 46907198144844 Dragino LSN50v2-D20 LoRaWAN Waterproof Outdoor Temperature Sensor (EU868) Dragino Trade Bestsellers > Components > IoT & LoRa > Platforms > Sensors & LiDAR 020005 The temperature sensor used in LSN50v2-D20 is DS18B20, which can measure -55°C ~ 125°C with accuracy ±0.5°C (max ±2.0 °C). The sensor cable is made by Silica Gel, and the connection between the metal probe and cable is double compressed for waterproof, moisture-proof, and anti-rust for long-term usage. The LSN50v2-D20 supports a temperature alarm feature, the user can set a temperature alarm for instant notice. It is powered by an 8500mAh Li-SOCI2 battery, It is designed for long-term use up to 10 years. Each LSN50v2-D20 is pre-load with a set of unique keys for LoRaWAN registration, register these keys to the local LoRaWAN server and it will auto-connect after power on. Features LoRaWAN v1.0.3 Class A Ultra-low power consumption External DS18B20 Probe (default 2meters) Measure range -55°C ~ 125°C Temperature alarm AT Commands to change parameters Uplink on periodically or Interrupt Downlink to change configure Applications Wireless Alarm and Security Systems Home and Building Automation Automated Meter Reading Industrial Monitoring and Control Long-range Irrigation Systems https://www.elektor.com/cdn/shop/files/dragino_lsn50v2-d20_-_overview.jpg?v=1689090030https://www.elektor.com/cdn/shop/files/dragino_lsn50v2-d20_-_top_view.jpg?v=1696852917https://www.elektor.com/products/dragino-lsn50v2-d20-lorawan-waterproof-outdoor-temperature-sensor-eu868?variant=46907198144844 in stock 64.95 14 0 6.9 2 - 4 Werktage 46907198406988 Dragino LSN50v2-S31 LoRaWAN Temperature & Humidity Sensor (EU868) Dragino Trade Bestsellers > Components > IoT & LoRa > Platforms > Sensors & LiDAR 020006 The temperature & humidity sensor used in LSN50v2-S31 is SHT31, which is fully calibrated, linearized, and temperature compensated digital output from Sensirion, it provides strong reliability and long-term stability. The SHT31 is fixed in a waterproof anti-condensation casing for long-term use. The LSN50v2-S31 supports a temperature and humidity alarm feature, the user can get an alarm for instant notice. LSN50v2-S31 is powered by an 8500mAh Li-SOCI2 battery, It is designed for long-term use up to 10 years. Each LSN50v2-S31 is pre-load with a set of unique keys for LoRaWAN registration, register these keys to the local LoRaWAN server and it will auto-connect after power on. Features LoRaWAN v1.0.3 Class A Ultra-low power consumption External 3m SHT31 probe Measure range -40°C ~ 80°C Temperature alarm AT Commands to change parameters Uplink on periodically or Interrupt Downlink to change configure Applications Wireless Alarm and Security Systems Home and Building Automation Automated Meter Reading Industrial Monitoring and Control Long-range Irrigation Systems Temperature Sensor Range: -40 to + 80 °C Accuracy: ±0.2 @ 0-90 °C Resolution: 0.01 °C Long Term Shift: <0.03 °C/yr Humidity Sensor Range: 0 ~ 99.9% RH Accuracy: ± 2% RH (0 ~ 100% RH) Resolution: 0.01% RH Long Term Shift: <0.25% RH/yr Downloads Datasheet User Manual Firmware https://www.elektor.com/cdn/shop/files/dragino_lsn50v2-s31_lorawan_temperature_humidity_sensor_868_mhz_-_overview.jpg?v=1689090038https://www.elektor.com/cdn/shop/files/dragino_lsn50v2-s31_lorawan_temperature_humidity_sensor_868_mhz_-_top_view.jpg?v=1696852923https://www.elektor.com/products/dragino-lsn50v2-s31-lorawan-temperature-humidity-sensor-eu868?variant=46907198406988 in stock 69.95 15 0 6.9 2 - 4 Werktage 46907091583308 Dragino LWL01 LoRaWAN Water Leak Sensor (EU868) Dragino Trade Bestsellers > Components > IoT & LoRa > Platforms > Sensors & LiDAR 019390 LWL01 is powered by a CR2032 coin battery, in a good LoRaWAN Network Coverage case, it can transmit as many as 12,000 uplink packets (based on SF 7, 14 dB). In poor LoRaWAN network coverage, it can transmit ~ 1,300 uplink packets (based on SF 10, 18.5 B). The design goal for one battery is up to 2 years. User can easily change the CR2032 battery for reuse. The LWL01 will send periodically data every day as well as for water leak event. It also counts the water leak event times and also calculates last water leak duration. Each LWL01 is pre-load with a set of unique keys for LoRaWAN registration, register these keys to local LoRaWAN server and it will auto connect after power on. Features LoRaWAN v1.0.3 Class A SX1262 LoRa Core Water Leak detect CR2032 battery powered AT Commands to change parameters Uplink on periodically and water leak event Downlink to change configure Applications Wireless Alarm and Security Systems Home and Building Automation Industrial Monitoring and Control https://www.elektor.com/cdn/shop/files/dragino_lwl01_lorawan_water_leak_sensor.jpg?v=1689087357https://www.elektor.com/products/dragino-lwl01-lorawan-water-leak-sensor-eu868?variant=46907091583308 in stock 19.95 9 4.9 6.9 2 - 4 Werktage 46906988527948 Dragino MS14N-S Linux IoT Appliance with Sensor Terminal Dragino Trade Bestsellers > IoT & LoRa > Platforms It supports generic OpenWrt Linux version or modified OpenWrt version such as Arduino Yun. It has USB host port and has full Ethernet and 802.11 b/g/n WiFi capabilities.Applications for MS14N include remote control of robots, data logging, web applications for data presentation, mesh networking over WiFi and many more. Hardware System: CPU: AR9331 DDR RAM: 64 MB LASH: 16 MB Interface: 2 x 10 M/100 M RJ45 interface 1 x power input: 9 ~ 12 VDC 1 x USB Host Port 1 x internet USB interface 14 x screw terminal positions WiFi Spec: Protocol: 802.11 b/g/n Frequency: 2,412 - 2,472 GHz Power: 100 mW https://www.elektor.com/cdn/shop/files/ms14_1.jpg?v=1689084973https://www.elektor.com/cdn/shop/files/ms14_2.jpg?v=1696849318,https://www.elektor.com/cdn/shop/files/ms14_4.jpg?v=1696849318,https://www.elektor.com/cdn/shop/files/ms14_7.jpg?v=1698679039https://www.elektor.com/products/dragino-ms14n-s-linux-iot-appliance-with-sensor-terminal?variant=46906988527948 in stock 49.95 9 4.9 6.9 2 - 4 Werktage 46906945438028 DVD Elektor 1980-1989 (NL) Elektor Sticks Archives > Bestsellers > Compilations > Elektor Products > No Member Discount > Sale 9789053811986 DVD Elektor 1980-1989 (NL) https://www.elektor.com/cdn/shop/files/dvd_10jahre_1980-89_nl.png?v=1689083774https://www.elektor.com/cdn/shop/files/dvd-elektor-1980-1989-nl_400.jpg?v=1696848670https://www.elektor.com/products/dvd-elektor-1980-1989-nl?variant=46906945438028 in stock 69.0 24.95 47 4.9 6.9 2 - 4 Werktage 46863962177868 DVD Elektor 1990-1999 (NL) Elektor Sticks Archives > Bestsellers > Compilations > Elektor Products > No Member Discount > Sale 9789053812150 DVD Elektor 1990-1999 (NL) https://www.elektor.com/cdn/shop/products/dvd_nl_1990-1999-2.png?v=1688039108https://www.elektor.com/cdn/shop/files/dvd_nl_1990-1999-1.png?v=1696848498https://www.elektor.com/products/dvd-elektor-1990-1999-nl?variant=46863962177868 in stock 89.0 19.95 44 4.9 6.9 2 - 4 Werktage 46906939605324 DVD Elektor 2000-2009 (NL) Elektor Sticks Archives > Bestsellers > Compilations > Elektor Products > No Member Discount > Sale 9789053812938 DVD Elektor 2000-2009 (NL) https://www.elektor.com/cdn/shop/files/dvd_2000-2009_nl.png?v=1689083605https://www.elektor.com/cdn/shop/files/dvd_2000-2009_nl_b.png?v=1696848578https://www.elektor.com/products/dvd-elektor-2000-2009-nl?variant=46906939605324 in stock 89.0 34.95 22 4.9 6.9 2 - 4 Werktage 46907074150732 DVD Elektor 2010-2019 (NL) Elektor Sticks Archives > Bestsellers > Compilations > Elektor Products > No Member Discount > Sale 9789053813041 DVD Elektor 2010-2019 (NL) https://www.elektor.com/cdn/shop/files/dvd-elektor-2010-2019_nl.png?v=1689086550https://www.elektor.com/products/dvd-elektor-2010-2019-nl?variant=46907074150732 in stock 89.0 29.95 99 4.9 6.9 2 - 4 Werktage 46907188642124 DVI Sock for Raspberry Pi Pico Elektor Trade Bestsellers > Pico RP2040 > Raspberry Pi 0608603905328 Unlike other Raspberry Pi boards, the Raspberry Pi Pico does not have a built-in video output.However, thanks to programmable IO (PIO) and this Pico DVI Sock, it is possible to add a DVI video output to the Raspberry Pi Pico!The Pico DVI Sock was developed by Luke Wren, a Raspberry Pi engineer, in his spare time. He has published the design online under a CC0 license, so everybody can build the hardware from his provided files.The physical video interface of the Pico DVI Sock is an HDMI connector, but it outputs a DVI signal. Historically, HDMI is a successor to DVI – so DVI signals can be simply transmitted using HDMI. Simple passive adapters allow you to connect HDMI cables to a DVI port.The DVI Sock can be soldered to one end of the Raspberry Pi Pico. Thanks to the castellated edges of the Pico, soldering is very easy. Let your creativity run wild with an additional digital video output on the Pico.Here are some suggestions / possible project ideas:Mini game console based on the Raspberry Pi PicoOutput of measurement values on a monitor https://www.elektor.com/cdn/shop/files/dvi-sock-for-raspberry-pi-pico.jpg?v=1689089635https://www.elektor.com/products/dvi-sock-for-raspberry-pi-pico?variant=46907188642124 in stock 7.95 8 4.9 6.9 2 - 4 Werktage 46906938720588 EAGLE V6 Getting Started Guide (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46906938720588-has-digital-downloads 9781907920202 Whether you are an electronics enthusiast or engineering professional, this book provides the reader with an introduction to the use of the CadSoft’s EAGLE PCB design software package.EAGLE is a user-friendly, powerful and affordable software package for the efficient design of printed circuit boards. It offers the same power and functionality to all users, at a smaller cost than its competitors. A free version of EAGLE is available to enthusiasts for their own use.EAGLE can be used on the main computing platforms including: Microsoft Windows (XP, Vista or Windows 7); Linux (based on kernel 2.6 or above) and Apple Mac OS X (Version 10.6 or higher). Any hardware that supports these software platforms will run the EAGLE application.The book is intended for anyone who wants an introduction to the capabilities of EAGLE. The reader may be a novice at PCB design or a professional wanting to learn about EAGLE, with the intention of migrating from another CAD package.This book will quickly allow you to:obtain an overview of the main modules of EAGLE: the schematic editor; layout editor and autorouter in one single interface;learn to use some of the basic commands in the schematic and layout editor modules of EAGLE;apply your knowledge of EAGLE commands to a small project;learn more about some of the advanced concepts of EAGLE and its capabilities;understand how EAGLE relates to the stages of PCB manufacture;create a complete project, from design through to PCB fabrication. The project discussed in the book is a popular, proven design from the engineering team at Elektor.After reading this book while practicing some of the examples, and completing the projects, the reader should feel confident about taking on more challenging endeavors. For the more sophisticated user … a more comprehensive guide and reference to EAGLE is now available from Elektor. Click here for more details! https://www.elektor.com/cdn/shop/files/eagle_v6_frontal.png?v=1689083580https://www.elektor.com/cdn/shop/files/eagle-v6_500.jpg?v=1696848566https://www.elektor.com/products/eagle-v6-getting-started-guide-e-book?variant=46906938720588 in stock 23.95 0 4.9 6.9 2 - 4 Werktage 46907219444044 Easel Board for AxiDraw (Tabloid/A3) Evil Mad Science Trade Bestsellers > Measuring Tools > Plotters > Production & Repair 020123 Extra easel boards for AxiDraw V3/A3 can be used as replacements, or for staging additional workpieces for quickly swapping to the next plot. This set consists of one 11.75 x 17 inch (29.85 x 43.18 cm) hardboard platen with rubber feet attached, plus eight micro binder clips. https://www.elektor.com/cdn/shop/files/easel-board-for-axidraw-tabloid-a3.jpg?v=1689090671https://www.elektor.com/products/easel-board-for-axidraw-tabloid-a3?variant=46907219444044 in stock 17.95 5 4.9 6.9 2 - 4 Werktage 46907086438732 EasyVR 3 Plus Shield for Arduino Elektor Trade Arduino > Arduino Shields > Bestsellers 8052461780016 Do you make time to talk to your Arduino? Maybe you should! The EasyVR 3 Plus Shield is a voice recognition shield for Arduino boards integrating an EasyVR module. This kit includes the EasyVR 3 Plus Module, the Arduino Shield Adapter, microphone, and headers. With all of these parts, everything has been provided to you to get up and running in a short amount of time with minimal soldering! EasyVR 3 Plus is a multi-purpose speech recognition module designed to add versatile, robust and cost effective speech recognition capabilities to almost any application. The EasyVR 3 Plus module can be used with any host with a UART interface powered at 3.3V – 5V, such as PIC and Arduino boards. Some application examples include home automation, such as voice-controlled light switches, locks, curtains or kitchen appliances, or adding “hearing” to the most popular robots on the market. Note: Please be aware that the EasyVR 3 Plus Shield for Arduino does not come pre-assembled and will require some soldering and assembly before operation. Includes EasyVR 3 Plus Module EasyVR Shield 3 Wired Microphone Speaker cable (Speaker not included) Header Set Features Up to 256 user-defined Speaker Dependent (SD) or Speaker Verification (SV) commands, that can be trained in ANY language, divided into maximum 16 groups (up to 32 SD or 5 SV commands each). A selection of 26 built-in Speaker Independent (SI) commands for ready-to-run basic controls, in the following languages: US English French German Italian Japanese Spanish Other SI commands freely downloadable from the Fortebit website (downloads section). SonicNet™ technology for wireless communications between modules or any other sound source (Audio CD, DVD, MP3 Player). Up to around 21 minutes of pre-recorded sounds or speech. Up to about 137 seconds of live message recording and playback. Real-time Lip-sync capability. DTMF tone generation. Differential audio output that directly supports 8Ω speakers. Easy-to-use Graphical User Interface to program Voice Commands and audio. Standard UART interface (powered at 3.3V - 5V). Simple and robust documented serial protocol to access and program through the host board. Six General purpose I/O lines that can be controlled via UART commands. With the optional Quick T2SI Lite license, up to 28 custom Speaker Independent (SI) command vocabularies, with up to 12 commands each, for a total of 336 possible commands in the following languages: US English British English French German Italian Japanese Korean Mandarin Spanish Compatible with Arduino boards that have the 1.0 Shield interface (UNO R3) including, but not limited to: Arduino Zero Arduino Uno Arduino Mega Arduino Leonardo Arduino Due Supports 5V and 3.3V main boards through the IOREF pin (defaults to 5V if this pin is absent) Supports direct connection to the PC on main boards with a separate USB/Serial chip and a special software-driven “bridge mode” on boards with only native USB interface, for easy access and configuration with the EasyVR Commander Enables different modes of serial connection and also flash updates to the embedded EasyVR module (through the Mode Jumper) Supports remapping of serial pins used by the Shield (in SW mode) Provides a 3.5mm audio output jack suitable for headphones or as a line out https://www.elektor.com/cdn/shop/files/15453-easyvr_3_plus_shield_for_arduino-09.jpg?v=1689087114https://www.elektor.com/cdn/shop/files/15453-white_easyvr_3_plus_shield_for_arduino-07.jpg?v=1696850931,https://www.elektor.com/cdn/shop/files/15453-white_easyvr_3_plus_shield_for_arduino-05.jpg?v=1696850931,https://www.elektor.com/cdn/shop/files/15453-white_easyvr_3_plus_shield_for_arduino-03.jpg?v=1698679107,https://www.elektor.com/cdn/shop/files/15453-white_easyvr_3_plus_shield_for_arduino-06.jpg?v=1698679108,https://www.elektor.com/cdn/shop/files/15453-white_easyvr_3_plus_shield_for_arduino-02.jpg?v=1698679108,https://www.elektor.com/cdn/shop/files/15453-white_easyvr_3_plus_shield_for_arduino-04.jpg?v=1698679107,https://www.elektor.com/cdn/shop/files/15453-easyvr_3_plus_shield_for_arduino-12.jpg?v=1698679107,https://www.elektor.com/cdn/shop/files/15453-easyvr_3_plus_shield_for_arduino-11.jpg?v=1698679107https://www.elektor.com/products/easyvr-3-plus-shield-for-arduino?variant=46907086438732 in stock 47.95 5 4.9 6.9 2 - 4 Werktage 46906943635788 EggBot Deluxe - Open-source Art Robot Evil Mad Science Trade Bestsellers > Fun Electronics > Measuring Tools > Plotters > Production & Repair 799422830554 The EggBot is a friendly art robot that can draw on spherical or egg-shaped objects from the size of a ping pong ball to that of a small Grapefruit – roughly 1.25 to 4.25 inches in diameter (3 - 10 cm). You can use EggBot on all kinds of spherical objects. Use it to create the most impressive Easter eggs, personalize Christmas ornaments or even golf balls or light bulbs. The EggBot is not just a cool gadget; it’s also a great introduction to CNC (computer numerical control) and do-it-yourself robotics. All of the electronics and software are designed to be hackable and repurposable, so you could easily computer control an Etch-a-Sketch or create something totally new. The EggBot software allows you to control the ‘bot from within Inkscape – a superb freeware illustration program – on Mac, Windows, or Linux computers. You can draw an image directly, trace a photograph, or import designs from other programs. You can also control the EggBot directly from many other programs that have the ability to send serial commands over a USB port. The EggBot kit in the Elektor online store is the most popular of all; the Deluxe Version! The EggBot kits are recommended for ages 10 and up, although for kids under 13 adult supervision is recommended. Universal power supply included! (with US-EU adapter). https://www.elektor.com/cdn/shop/files/eggbot.jpg?v=1698679130https://www.elektor.com/cdn/shop/files/graceegg-640.jpg?v=1698679130,https://www.elektor.com/cdn/shop/files/13725453175_755406d873.jpg?v=1698679130,https://www.elektor.com/cdn/shop/files/4969970725_61bea8320e_b.jpg?v=1698679130,https://www.elektor.com/cdn/shop/files/140570-91c-web.jpg?v=1698679130,https://www.elektor.com/cdn/shop/files/140570-91d-web.jpg?v=1698679130,https://www.elektor.com/cdn/shop/files/140570-91b-web.jpg?v=1698679130,https://www.elektor.com/cdn/shop/files/140570-91e-web.jpg?v=1698679130https://www.elektor.com/products/eggbot-deluxe-open-source-art-robot?variant=46906943635788 in stock 259.0 9 0 0 2 - 4 Werktage 46906960970060 EggBot Pro - Open-source Art Robot Evil Mad Science Trade Bestsellers > Fun Electronics > Measuring Tools > Plotters > Prototyping 799422830608 The EggBot Pro is a complete re-imagining of the EggBot, designed for rigidity, ease of use, and faster setup. Its major components are solid aluminum, CNC machined in the USA, and powder coated or anodized. It's sturdy as can be. The frame has an open front, for greatly improved accessibility and visibility while you are plotting. The most common mechanical adjustments are faster with bicycle-style quick releases and repositioned thumbscrews for easier access. And, it comes fully assembled and ready to use. Assuming that you've installed the software first, you can be up and printing within minutes of opening the box. The EggBot Pro fits spherical and egg-shaped objects from roughly the size of a gumball to that of a light bulb — about 1 to 3.5 inches in diameter (2.5 - 9 cm). Perfect for ping pong balls, golf balls, chicken eggs, and similarly sized objects. The movements of the pen and egg motors are controlled by high-torque precision stepping motors, and the pen lift mechanism is a quiet and reliable servo motor. The included EiBotBoard v2.0 (EBB) driver board uses 16× micro stepping to give a resolution of 3200 steps/revolution in both axes. A universal-input plug-in power supply is included with the EggBot kit, as is a USB cable and one black Sharpie marker. To operate the EggBot Pro, you will need a reasonably modern computer with an available USB port (Mac, Windows or Linux), plus internet access to download the necessary software. The EggBot is usually controlled through a set of open-source extensions to Inkscape, the excellent, popular and free vector graphics program. The basic operation is much like that of a printer driver: you import or make a drawing in Inkscape, and use the extensions to plot your drawing onto whatever object you've mounted in the EggBot. It's all handled through an easy to use graphical user interface and works cleanly on Mac, Windows, and Linux. The standard pen holder included with the EggBot kit is designed to fit various art pens including Sharpie Ultra Fine Point and Sharpie Fine Point pens. However, it can fit almost any pen of similar size. You can even fit a lot of things that aren't pens. One example: We offer a diamond point engraving tool for EggBot (shown here), capable of etching and engraving hard materials like glass, stone, and ceramic. https://www.elektor.com/cdn/shop/files/egg-bot-pro-eggbot-in-action.jpg?v=1689084052https://www.elektor.com/cdn/shop/files/5.jpg?v=1696848822,https://www.elektor.com/cdn/shop/files/4.jpg?v=1696848822,https://www.elektor.com/cdn/shop/files/1.jpg?v=1698679142,https://www.elektor.com/cdn/shop/files/8.jpg?v=1698679142,https://www.elektor.com/cdn/shop/files/6.jpg?v=1698679142https://www.elektor.com/products/eggbot-pro-open-source-art-robot?variant=46906960970060 in stock 349.0 5 0 0 2 - 4 Werktage 46907219214668 EiBotBoard (EBB) Driver Board Evil Mad Science Trade Bestsellers > Components > Measuring Tools > Motors > Plotters > Production & Repair 020122 The EiBotBoard ('EBB') is a USB-based dual stepper motor controller board that is useful for many general purpose robotics applications. Originally designed for the EggBot project, it is the 'brain' of all current models of the EggBot, but also of the AxiDraw and WaterColorBot as well. The EBB was designed by Brian Schmalz of Schmalz Haus LLC. It is an open source (in both hardware and software), PIC18F46J50-based motor controller board. Standard features include two Allegro A4983 16X microstepping motor drivers for bipolar steppers. It also has a separate onboard regulator to power up to two hobby servo motors. It is 2.2 x 2.2 inches square (5.6 x 5.6 cm). We are currently shipping version 2.7 of the EBB, which features several improvements for reliability. Version 2.7 uses a standard USB micro connector and has a switch that by default turns off power to the pen-lift servo motor after one minute of inactivity. You can change the timeout duration or disable this feature using the serial command protocol. Specifications Motor driver ICs: Two Allegro A4983 Stepper motor type: Bipolar (2) Step size: Full, 1/2, 1/4, 1/8, 1/16 Motor connectors: Screw terminal USB jack type: Micro-B Power connector: Barrel Jack, 2.1 x 5.5 mm, center positive Voltage input range: 9-25 V DC Output current adjustment: 46 mA to 1.25 A per phase Downloads/Documentation GitHub https://www.elektor.com/cdn/shop/files/eibotboard-ebb-driver-board.jpg?v=1689090663https://www.elektor.com/cdn/shop/files/eibotboard-ebb-driver-board_front.jpg?v=1696853481https://www.elektor.com/products/eibotboard-ebb-driver-board?variant=46907219214668 in stock 69.95 3 0 6.9 2 - 4 Werktage 47754474389836 Elecrow 10.1" IPS Touch Display (1280x800) Elecrow Trade Bestsellers > Components > Displays > Displays & LEDs > NEW 020791 This 10.1-inch HDMI touch screen has a high-definition resolution of 1280x800 and supports a viewing angle of 178°, providing an excellent visual experience. It supports Raspberry Pi, Windows, Linux, Ubuntu and other systems, and is also compatible with Raspberry Pi 3/3B+/4B/5, Jetson Nano, Beaglebone, Banana Pi and other mainstream development boards. You can easily adjust the desired brightness by adjusting the backlight button.This Raspberry Pi capacitive touch screen supports 5-point touch, has fast response speed, and high-definition communication supports plug-and-play.It comes with a stand for easy desktop placement, and mounting holes on the back allow you to securely mount it on a wall or integrate it with a small form factor SBC (single board computer).To protect the screen and enhance its visual appeal, the monitor comes with a durable and stylish acrylic cover.Whether you need a high-quality monitor for gaming, multimedia entertainment, or industrial applications, our 10-inch monitors offer superior visuals, responsive touch controls, seamless connectivity, and versatile mounting options.FeaturesIPS HD 1280x800 resolution and 178° full viewing angle offers crystal clear visuals and vivid colors for high-quality visual experienceSupport backlight control, itcan be adjusted by buttonSupport capacitive 5-point touch, enable smooth, accurate and fast responseUse HD communication, plug and play, and easy to useSupport Windows, Linux, Ubuntu, Kodi, etc.Compatible with Raspberry Pi 3/3B+/4B/5, Jetson Nano, BeagleboneSpecificationsScreen Size10.1 inchScreen TypeIPS screenResolution1280 x 800Backlight adjustmentKey switch adjustmentTouch Screen TypeCapacitive Touch ScreenTouch ICSIS9200PowerMicro-USB (5 V)Overall power5.2942 W (100% brightness)Video Input InterfaceHDMI-Compatible (up to 1080p)Active Area216.6 x 135.4 mmDimensions (L x W x H)239.4 x 157.4 x 12.3 ±0.2 mmIncluded1x 10.1 inch Touch Display1x HD to HD Cable2x USB cable1x HD to Mini HD Adapter1x Screw Pack2x Bracket1x Screwdriver1x ManualDownloadsManualWiki https://www.elektor.com/cdn/shop/files/Elecrow-10.1-IPS-Touch-Display-1280x800.jpg?v=1712309648https://www.elektor.com/cdn/shop/files/Elecrow-10.1-IPS-Touch-Display-1280x800_features.jpg?v=1712309681,https://www.elektor.com/cdn/shop/files/Elecrow-10.1-IPS-Touch-Display-1280x800_inputs.jpg?v=1712309700,https://www.elektor.com/cdn/shop/files/Elecrow-10.1-IPS-Touch-Display-1280x800_touchscreen.jpg?v=1712309711,https://www.elektor.com/cdn/shop/files/Elecrow-10.1-IPS-Touch-Display-1280x800_included.jpg?v=1712309726https://www.elektor.com/products/elecrow-10-1-ips-touch-display-1280x800?variant=47754474389836 in stock 109.95 9 0 0 2 - 4 Werktage 46907075330380 Electric Guitar (2nd Edition) Elektor Publishing Books Bestsellers > Books > Books | Audio & RF 9783895767779 Sound Secrets and Technology What would today’s rock and pop music be without electric lead and bass guitars? These instruments have been setting the tone for more than sixty years. Their underlying sound is determined largely by their electrical components. But, how do they actually work? Almost no one is able to explain this to the true musician with no technical background. This book answers many questions simply, in an easily-understandable manner. For the interested musician (and others), this book unveils, in a simple and well-grounded way, what have, until now, been regarded as manufacturer secrets. The examination explores deep within the guitar, including pickups and electrical environment, so that guitar electronics are no longer considered highly secret. With a few deft interventions, many instruments can be rendered more versatile and made to sound a lot better – in the most cost-effective manner. The author is an experienced electronics professional and active musician. He has thoroughly tested everything described here, in practice. https://www.elektor.com/cdn/shop/files/electric-guitar-2nd-edition.png?v=1689086623https://www.elektor.com/products/electric-guitar-2nd-edition?variant=46907075330380 in stock 34.95 143 4.9 6.9 2 - 4 Werktage 46907075985740 Electric Guitar (2nd Edition) (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907075985740-has-digital-downloads Sound Secrets and Technology What would today’s rock and pop music be without electric lead and bass guitars? These instruments have been setting the tone for more than sixty years. Their underlying sound is determined largely by their electrical components. But, how do they actually work? Almost no one is able to explain this to the true musician with no technical background. This book answers many questions simply, in an easily-understandable manner. For the interested musician (and others), this book unveils, in a simple and well-grounded way, what have, until now, been regarded as manufacturer secrets. The examination explores deep within the guitar, including pickups and electrical environment, so that guitar electronics are no longer considered highly secret. With a few deft interventions, many instruments can be rendered more versatile and made to sound a lot better – in the most cost-effective manner. The author is an experienced electronics professional and active musician. He has thoroughly tested everything described here, in practice. https://www.elektor.com/cdn/shop/files/electric-guitar-2nd-edition-pdf.png?v=1689086638https://www.elektor.com/products/electric-guitar-2nd-edition-e-book?variant=46907075985740 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 46906986692940 Electric Paint Lamp Kit Bare Conductive Trade Bestsellers > Components > Displays & LEDs > Education > Kits > No Member Discount > Sale 5060322451107 The Electric Paint Lamp Kit is a great gift!Transform any piece of paper into a touch-sensitive lamp with Electric Paint! Make three paper lamps with no tools, no programming, no special skills required.Included1x Light Up Board1x Electric Paint 10ml Tube1x Micro USB Cable1x Touch Lamp Template1x Dimmer Lamp Template1x Proximity Lamp Template1x Instruction Test SheetTransform a paper template into a beautiful lamp in three easy steps. Paint, plug, and play! Use Electric Paint to create custom touch-sensitive buttons connected to our Light Up Board and then use our lampshades to bring your lamp to life.LEVEL: BeginnerThe Electric Paint Lamp Kit is easy to use and makes a perfect gift. The Touch, Dimmer, and Proximity lamps all show off different aspects of Electric Paint and the Light Up Board and are perfect for your home, office or workshop.About Electric PaintYour design and electronics projects are about to change forever with this easy to use electrically conductive paint. Paint circuits or use as a conductive adhesive on almost anything including paper, plastic, textiles and conventional electronics.About the Light Up BoardThe Light Up Board is the heart of the Electric Paint Lamp Kit. It works straight out of the box, is powered by USB and requires no programming or special tools. The board’s six bright LEDs and three different modes provide the light for your lamps and the super easy connector system means that you can create lamps on any sheet material. https://www.elektor.com/cdn/shop/files/electronic-paint-lamp-kit-elektor.png?v=1689084861https://www.elektor.com/cdn/shop/files/electric-paint-lamp-kit_hands.jpg?v=1696849261,https://www.elektor.com/cdn/shop/files/electric-paint-lamp-kit_contents.jpg?v=1696849261,https://www.elektor.com/cdn/shop/files/electric-paint-lamp-kit_dimmer.jpg?v=1696849260,https://www.elektor.com/cdn/shop/files/electric-paint-lamp-kit_proximity.jpg?v=1696849260https://www.elektor.com/products/electric-paint-lamp-kit?variant=46906986692940 in stock 52.95 39.95 7 4.9 6.9 2 - 4 Werktage 47318771499340 Electromagnetic Radiation Tester WT3122 Elektor Boards&Kits Analyzers > Bestsellers > Elektor Labs Selection > NEW > No Member Discount > Sale 020521 This radiation survey meter can test electric field radiation and magnetic field emission to reach the optimal test result. It is used to test and learn electromagnetic radiation situations indoor and outdoor. It is equipped with a built-in electromagnetic radiation sensor, which can display the radiation value on the LCD after processing by the control microchip. You can make reasonable processing or taking effective prevention measures toward the electromagnetic radiation according to the test result. Features One detector for two uses, simultaneous detection of electric and magnetic field radiation Color-screen display Sound and light alarm, automatic alarm above safe value Press one button to lock radiation value (data lock) LCD graphic display of radiation value trend Radiation assessment, indicating if current radiation value is at safe level Easy to operate with one hand, move or perform on-site measurement Applications Electromagnetic radiation monitoring: House and apartment, office, outdoor and industrial site Electromagnetic radiation test: Mobile phone, computer, TV set, refrigerator and high voltage cable radiation test Radiation protection product test: Test effects of radiation-proof clothes, radiation-proof film and other prevention articles Specifications Electric field Magnetic field Unit V/m uT / mG Accuracy 1 V/m 0.01 uT/ 0.1 mG Range 1~1999 V/m 0.01~99.99 uT/ 0.1~999.9 mG Alarm threshold 40 V/m 0.4 uT/4 mG Reading display 3½ digit LCD Measurement bandwidth 5 Hz~3500 MHz Sampling time About 0.4s Measurement mode Dual mode at the same time Overload indication Maximum value of measurement range on LCD Operation temperature 0~50°C Operation humidity Relative humidity below 80% Working voltage 3.7 V Power 3.7 V Lithium battery Dimensions 61 x 25 x 134 mm Weight 131 g Downloads Manual https://www.elektor.com/cdn/shop/files/electromagnetic-radiation-tester-wt3122.jpg?v=1699464704https://www.elektor.com/cdn/shop/files/electromagnetic-radiation-tester-wt3122_side.jpg?v=1699544562,https://www.elektor.com/cdn/shop/files/electromagnetic-radiation-tester-wt3122_contents.jpg?v=1699544562,https://www.elektor.com/cdn/shop/files/electromagnetic-radiation-tester-wt3122_package.jpg?v=1699544563https://www.elektor.com/products/electromagnetic-radiation-tester-wt3122?variant=47318771499340 in stock 44.95 29.95 228 4.9 6.9 2 - 4 Werktage 46907243528524 Electronic Circuits For All (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907243528524-has-digital-downloads 978-1-907920-65-3 This book contains more than 400 simple electronic circuits which are developed and tested in practice by the authors. The technical solutions presented in the book are intended to stimulate the creative imagination of readers and broaden their area of thought. This should allow readers to look beyond the horizons of possibilities and use ordinary electronic items in a new way. This book includes new and original radio electronic multipurpose circuits. The chapters of the book are devoted to power electronics and measuring equipment and contain numerous original circuits of generators, amplifiers, filters, electronic switches based on thyristors and CMOS switch elements. Wired and wireless systems as well as security and safety systems are presented. Due to the high relevance and increased interest of readers in little-known or not readily available information, the different chapters of this book describe the use of electronic devices in industrial electronics and for research, as well as new instruments and equipment for medical use, gas-discharge and Kirlian photography. A number of technical devices presented in this book are related to research of the mysteries of the earth, nature and human beings by using radio electronic devices. This book will be useful for both radio amateurs and professionals. https://www.elektor.com/cdn/shop/files/electronic-circuits-for-all-pdf.png?v=1689091711https://www.elektor.com/products/electronic-circuits-for-all-e-book?variant=46907243528524 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 46907180810572 Electronic Security and Espionage Elektor Publishing Books Bestsellers > Books > Books | Electronics > NEW 9783895764653 A Handbook on DIY Nowadays, security problems are rarely properly solved or correctly addressed. Electronic security is only part of the chain in making a system secure. Electronic security is usually addressed as network or software security, neglecting other aspects, but the chain is only as strong as its weakest link. This book is about electronic hardware security, with an emphasis on problems that you can solve on a shoestring DIY budget. It deals mostly with secure communications, cryptosystems, and espionage. You will quickly appreciate that you can’t simply buy a trustworthy and reliable cryptosystem off the shelf. You will then realise that this applies equally to individuals, corporations, and governments. If you want to increase your electronic security awareness in a world already overcrowded with networks of microphones and cameras, this is a book for you. Furthermore, if you want to do something DIY by designing and expanding upon simple electronic systems, please continue reading. Some of the devices described are already published as projects in the Elektor magazine. Some are still ideas yet to be worked out. Complexity is the main enemy of security, so we'll try to keep to simple systems. Every chapter will analyse real-life espionage events or at least several hypothetical scenarios that will hopefully spark your imagination. The final goal is to build a security-conscious mindset (or “to get into a head of a spy”) which is necessary to recognise possible threats beforehand, to design a truly secure system. Don’t bother reading if: you think you and your secrets are 100% safe and secure you think somebody else can effectively handle your security you think conspiracy theories only exist in theory – Telefunken’s masterpiece the “FS-5000 Harpoon” was built on one! https://www.elektor.com/cdn/shop/files/electronic-security-and-espionage.png?v=1689089500https://www.elektor.com/products/electronic-security-and-espionage?variant=46907180810572 in stock 34.95 73 4.9 6.9 2 - 4 Werktage 46907180941644 Electronic Security and Espionage (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907180941644-has-digital-downloads 978-3-89576-466-0 A Handbook on DIY Nowadays, security problems are rarely properly solved or correctly addressed. Electronic security is only part of the chain in making a system secure. Electronic security is usually addressed as network or software security, neglecting other aspects, but the chain is only as strong as its weakest link. This book is about electronic hardware security, with an emphasis on problems that you can solve on a shoestring DIY budget. It deals mostly with secure communications, cryptosystems, and espionage. You will quickly appreciate that you can’t simply buy a trustworthy and reliable cryptosystem off the shelf. You will then realise that this applies equally to individuals, corporations, and governments. If you want to increase your electronic security awareness in a world already overcrowded with networks of microphones and cameras, this is a book for you. Furthermore, if you want to do something DIY by designing and expanding upon simple electronic systems, please continue reading. Some of the devices described are already published as projects in the Elektor magazine. Some are still ideas yet to be worked out. Complexity is the main enemy of security, so we'll try to keep to simple systems. Every chapter will analyse real-life espionage events or at least several hypothetical scenarios that will hopefully spark your imagination. The final goal is to build a security-conscious mindset (or “to get into a head of a spy”) which is necessary to recognise possible threats beforehand, to design a truly secure system. Don’t bother reading if: you think you and your secrets are 100% safe and secure you think somebody else can effectively handle your security you think conspiracy theories only exist in theory – Telefunken’s masterpiece the “FS-5000 Harpoon” was built on one! https://www.elektor.com/cdn/shop/files/electronic-security-and-espionage-pdf.png?v=1689089508https://www.elektor.com/products/electronic-security-and-espionage-e-book?variant=46907180941644 in stock 29.95 0 4.9 6.9 2 - 4 Werktage 46907161444684 Electronics Fans Package - Component Basic Starter Kit Kuongshun Trade Arduino > Arduino Kits > Bestsellers > Components > Kits > No Member Discount > Raspberry Pi > Raspberry Pi Kits AE072 Contents 1x High Quality Retail Box 10x 1/4W 1% 100R Resistor 10x 1/4W 1% 220R Resistor 10x 1/4W 1% 330R Resistor 10x 1/4W 1% 1K Resistor 10x 1/4W 1% 10K Resistor 10x 1/4W 1% 100K Resistor 10x 1/4W 1% 4.7K Resistor 10x 1/4W 1% 47K Resistor 10x 100PF Ceramic Capacitor 10x 10NF Ceramic Capacitor 10x 100NF Ceramic Capacitor 10x 22PF Ceramic Capacitor 10x 10UF aluminum electrolytic capacitor 10x 470UF aluminum electrolytic capacitor 10x Red LED 10x Green LED 10x Yellow LED 10x Blue LED 8x 12x12x7.3 Switch 2x Red Cap 2x Yellow Cap 2x Green Cap 2x Blue Cap 1x 10K Precision Potentiometer 2x RGB LED 1x Active Buzzer 1x Passive Buzzer 1x Pin Header 1x40 1x Resistor Card 1x 400pts Breadboard 1x 30pcs/pack Breadboard Jumper Wires Set https://www.elektor.com/cdn/shop/files/electronics-fans-package-component-basic-starter-kit.jpg?v=1689088983https://www.elektor.com/cdn/shop/files/electronics-fans-package-component-basic-starter-kit_contents.jpg?v=1696852227https://www.elektor.com/products/electronics-fans-package-component-basic-starter-kit?variant=46907161444684 in stock 19.95 14.95 18 4.9 6.9 2 - 4 Werktage 46907280294220 Electronics for Space (E-book) Elektor Digital E-books Bestsellers > Books > E-books (–20% for Members) has-digital-downloads,variant-46907280294220-has-digital-downloads 978-1-907920-72-1 Space, the final frontier, will become more and more popular. The space industry is continually growing and new products and services will be required. Innovation is needed for the development of this industry. Today it is no longer possible to follow all the events in field of space. The space market is growing and activities are increasing, especially the market for small-satellites.This book wants to help close the gap and encourage electronic engineers to enter into the fascinating field of space electronics. One of the main difficulties is finding people with knowledge of space electronics design. Nowadays companies have to invest a lot of time and resources to instruct electronic engineers with no experience of space. Only a brief and basic introduction of this topic is typically achieved at university in space engineering lectures. Professionals with practical experience and the necessary theoretical knowledge are scarce. Companies from the space sector are searching for staff with knowledge of space electronics.This book will bring space closer aspiring to the space electronic hobbyists. https://www.elektor.com/cdn/shop/files/electronics-for-space-pdf_1.png?v=1689093052https://www.elektor.com/products/electronics-for-space-e-book?variant=46907280294220 in stock 19.95 0 4.9 6.9 2 - 4 Werktage 46907233173836 Electronics Notebook MonkMakes Trade Basics > Bestsellers > Books > Books | Electronics > NEW 682698570340 Specifications A4 (210 x 297 mm) squared-grid spiral-bound notebook with watermark breadboards 158 pages, card covers. The book also includes Microcontroller programming cheat sheet Common circuits and calculations Pinouts Resistor color codes ASCII table https://www.elektor.com/cdn/shop/files/electronics-notebook.jpg?v=1689091362https://www.elektor.com/cdn/shop/files/electronics-notebook_page.jpg?v=1696853972https://www.elektor.com/products/electronics-notebook?variant=46907233173836 in stock 16.95 13 4.9 6.9 2 - 4 Werktage 47318768943436 Electronics Tool Set ZD-979B Zhongdi Trade Bestsellers > Measuring Tools > NEW 020479 This tool set contains essential tools for all kinds of electronic work. Included Soldering iron Desoldering pump Precision screwdriver 2.5x75 mm Screwdriver 3x75 mm Screwdriver 5x75 mm Screwdriver 6x125 mm Long nose plier (5') Diagonal cutting plier (4.5') IC extractor Wire stripper & cutter Multimeter Hex key wrench Soldering wire Component storage box Tweezers (Long nose) Bag size: 340 x 210 x 50 mm https://www.elektor.com/cdn/shop/files/electronics-tool-set-zd-979b.jpg?v=1699464582https://www.elektor.com/products/electronics-tool-set-zd-979b?variant=47318768943436 in stock 34.95 35 4.9 6.9 2 - 4 Werktage 46907277771084 Elektor 2 MHz LCR Meter Kit Eurocircuits Boards&Kits Analyzers > Comparison Websites DE > Comparison Websites FR > Elektor Kits > Elektor Products > LCR Meters > Measuring Tools > Test & Measurement Comparison Websites 7442105131105 Would you like to add an LCR Meter to your electronics workbench? Build your own! The Elektor 2 MHz LCR Meter Kit is an automatic impedance measuring bridge with extended functionality. Features Measures the resistance, capacitance and inductance of components with an impedance of 10 mΩ to 100 MΩ Test frequency from 50 Hz to 2 MHz Four possible test voltages (0.1, 0.2, 0.5 and 1 Vrms) Additional DC polarization up to 5 V for capacitors and 50 mA for inductors Two configurations possible: Standalone mode with main board + display extension Main board (without display) connected via USB to a computer running the user program (Windows, Linux, MacOS) Specifications Display Parameter valuesEquivalent circuitFrequencyImpedance ∣Z∣Phase ΦQ or DVoltage and current of DUTTest voltage (AC) and polarisation (DC)Range hold statusLabels for multi-function buttons Display size 4.1' (10.5 cm) | 240 x 128 dots Measurement range Parameter Value Inductance L 10 nH - 100 H Capacity C 1 pF - 100 mF Resistance R 10 mΩ - 100 MΩ Q 0 - 5000 for display Phase Φ -90° / +90° Test frequency 50 Hz to 2 MHz in 54 predefined stepsor any frequency within the range Accuracy Up to ± 0.1% ±1 of last digit Total current (MCU board + backlit display board) without polarization420 mA when polarizing DUTup to 650 mA Power supply 5 VDC/1 A USB A (not included)e.g. mobile phone mains charger PC software Windows, Linux, MacOS Dimensions (Hammond case) 6.5 x 4.2 x 2.1' (166 x 106 x 53 mm) Weight 1 kg All the necessary components are included for assembly and calibration: 2 populated PCBs (pushbuttons, rotary switch, and LCD)Note: Before shipping the operation of both assembled boards is carefully checked according to a protocol developed by the original designer Jean-Jacques Aubry. 4 BNC sockets (not assembled) 4 jumpers Hammond case drilled, machined, with printed front and side panels Kelvin cables with clips and 4 plugs Mini-USB / USB-A cable 24-way flat cable (15 cm) Aluminium button for rotary switch Full-color printed assembly manual (32 pages) Adjustment tool for trimmers Required tools Screwdriver, multimeter, and soldering iron. Time Total assembly and calibration time (depending on your skill): 60 to 90 minutes Downloads More downloads are available on the Elektor Labs platform. Elektor Jumpstarter This product is the result of a successful campaign on our electronics project support platform Elektor Jumpstarter. Readers and interested parties can submit their product ideas and, together with the Elektor development team, a finished product can be brought to market after extensive consideration and many tests. Note that these are always small series production runs, so the products are considered 'Elektor Collector Items'. https://www.elektor.com/cdn/shop/files/elektor-2-mhz-lcr-meter-kit.png?v=1698679203https://www.elektor.com/cdn/shop/files/lores_lcr_meter_kit_onderdelen_overzichtsbeeld_v2_dm.jpg?v=1698679203,https://www.elektor.com/cdn/shop/files/elektor-2-mhz-lcr-meter-kit_internal.png?v=1698679203,https://www.elektor.com/cdn/shop/files/elektor-2-mhz-lcr-meter-kit_case.png?v=1698679203,https://www.elektor.com/cdn/shop/files/elektor-2-mhz-lcr-meter-kit_package.png?v=1698679203,https://www.elektor.com/cdn/shop/files/elektor-2-mhz-lcr-meter-kit_manual.png?v=1698679203,https://www.elektor.com/cdn/shop/files/elektor-2-mhz-lcr-meter-kit_displays.png?v=1698679203,https://www.elektor.com/cdn/shop/files/board_-_display_-_with_soldered_buttons_001.jpg?v=1698679203,https://www.elektor.com/cdn/shop/files/board_-_mcu_-without_bnc_connectors_001.jpg?v=1698679203,https://www.elektor.com/cdn/shop/files/case_-_machined_bnc_side.jpg?v=1698679203,https://www.elektor.com/cdn/shop/files/case_-_machined_usb_side.jpg?v=1698679203,https://www.elektor.com/cdn/shop/files/option_partially_assembled_lcr-meter_001_cropped_b.jpg?v=1698679203https://www.elektor.com/products/elektor-2-mhz-lcr-meter-kit?variant=46907277771084 out of stock 799.0 0 0 0 nicht auf Lager 46906943963468 Elektor 37-in-1 Sensor Kit Elektor Labs Trade Arduino > Arduino Kits > Components > No Member Discount > Sensors & LiDAR 016843 Kit Contents 1x Joystick 1x Relay 1x Big Sound 1x Small Sound 1x Tracking 1x Avoidance 1x Flame 1x Linear Hall Sensor 1x Touch 1x Digital Temperature 1x Buzzer 1x Passive Buzzer 1x RGB LED 1x SMD RGB 1x Two Color (5 mm) 1x Mini Two Color (3 mm) 1x Reed Switch 1x Mini Reed Switch 1x Heartbeat 1x 7 Color Flash 1x Laser Emitter 1x PCB mounted push button 1x Shock, a rolling-ball type Tilt Switch 1x Rotary Encoders 1x Rolling ball Tilt Switch 1x Photoresistor 1x Temp and Humidity 1x Analog Hall 1x Hall Magnetic 1x DS18B20 Temp 1x Analog Temp 1x IR Emission 1x IR Receiver 1x Tap Module 1x Light Blocking Please note: For security reasons the Mercury Tilt Switch and Light Cup are no longer available in current sensor boxes. Downloads Manual https://www.elektor.com/cdn/shop/files/150001-91f_web.jpg?v=1696848371https://www.elektor.com/cdn/shop/files/150001-91i_web.jpg?v=1696848371,https://www.elektor.com/cdn/shop/files/150001-91h_web.jpg?v=1696848371,https://www.elektor.com/cdn/shop/files/150001-91g_web.jpg?v=1696848371,https://www.elektor.com/cdn/shop/files/sensor-box-branded-back.jpg?v=1698679214,https://www.elektor.com/cdn/shop/files/150001-91d-new-web.jpg?v=1698679213https://www.elektor.com/products/elektor-37-in-1-sensor-kit?variant=46906943963468 out of stock 49.95 29.95 0 4.9 6.9 nicht auf Lager 47474378015052 Elektor Archive 1961-2023 (USB Stick) NL Elektor Classics Sticks Archives > Bestsellers > Compilations > Elektor Products > NEW > No Member Discount > Sale > USB Sticks 020753 6 Elektor decennia (jaren '60, '70, '80, '90, '2000 en '2010) op USB-stick Deze USB-stick (32 GB, USB 3.0) bevat de complete jaargangen 1961-2023 (alle nummers) van het elektronica-vakblad Elektor. Elektor wil mensen inspireren om zich elektronica en computertechniek eigen te maken door het presenteren van nabouwvriendelijke, professioneel ontworpen schakelingen op alle terreinen van de elektronica: Audio & Video Basiskennis Computer & apparatuur Hobby & modelbouw Hoogfrequent Huis & tuin Meten & testen Microcontrollers Stroomvoorziening Al dat andere dat niet zo gemakkelijk in een van deze categorieën kan worden ondergebracht. De meer dan 10.000 afzonderlijke artikelen zijn chronologisch op publicatiedatum (maand/jaar) geordend. Systeemeisen Computer geschikt voor Adobe Reader vanaf versie 7 Webbrowser https://www.elektor.com/cdn/shop/files/ElektorArchive1961-2023USBStickNL.jpg?v=1705406437https://www.elektor.com/cdn/shop/files/ElektorArchive1961-2023USBStickNL_stick.jpg?v=1705406441https://www.elektor.com/products/elektor-archive-1961-2023-usb-stick-nl?variant=47474378015052 in stock 199.95 99.95 54 0 6.9 2 - 4 Werktage 47666406949196 Elektor Archive 1974-2023 (USB Stick) EN Elektor Classics Sticks Bestsellers > Compilations > Elektor Products > NEW > No Member Discount > Sale > USB Sticks 020751 NEW: Now incl. volume 2023!5 Elektor Decades (’70s, ’80s, ’90s, ’00s, and ’10s) on a USB StickThis handy USB stick (32 GB, USB 3.0) is loaded with all the Elektor magazine English editions (as PDFs) from 1974 to 2023. Elektor engineers, authors, and editors aim to inspire you to master electronics and computer technology by presenting professionally designed circuits that are easy to build.We also cover the latest developments in electronics and information technology. With the Elektor Archive on a USB stick, you can browse our previous English editions at your convenience and learn about MCU-based projects, robotics, electronics testing, embedded programming, analog techniques, and much more.All the Elektor magazine editions are stored as PDFs on a 32-GB USB stick (USB 3.0). The 10,000+ articles have been classified by date of publication (month/year), and a comprehensive index enables you to search the entire USB stick. Subject areas include:Audio & videoComputers & microcontrollersRadio, hobby & modellingHome & gardenPower supplies & batteriesTest & measurementSoftwareAnd everything else that doesn’t fit in one of these categories.System requirementsPC with Adobe Reader 7.0 or higherWeb browser https://www.elektor.com/cdn/shop/files/elektor_archive_1974-2023_usb_stick_en.jpg?v=1707314306https://www.elektor.com/cdn/shop/files/elektor_archive_1974-2023_usb_stick_en_stick.jpg?v=1707314306https://www.elektor.com/products/elektor-archive-1974-2023-usb-stick-en?variant=47666406949196 in stock 199.95 99.95 333 0 6.9 2 - 4 Werktage 46907178877260 Elektor Audio Collection (USB Stick) Elektor Classics Sticks Bestsellers > Compilations > Elektor Products > No Member Discount > USB Sticks 9783895764646 Some Highlights from the contents Surround-sound decoder Compact amp Sampling rate converter Battery powered preamplifier Titan 2000 amplifier Crescendo Millennium amplifier Audio-DAC/ADC IR-S/PDFI receiver and transmitter High-End Power Amp Hi-fi Wireless Headset Paraphase Tone Control and more… Using Adobe Reader you are able to browse and search the articles on your computer, as well as print texts, circuit diagrams and PCB layouts. https://www.elektor.com/cdn/shop/files/elektor-audio-collection-usb-stick.png?v=1689089455https://www.elektor.com/cdn/shop/files/elektor-audio-collection-usb-stick_classic.png?v=1696852503https://www.elektor.com/products/elektor-audio-collection-usb-stick?variant=46907178877260 in stock 69.95 39.95 167 4.9 6.9 2 - 4 Werktage 46907280130380 Elektor CheatKard (Electrical Engineering Reference Cards) Elektor Boards&Kits Bestsellers > Measuring Tools > No Member Discount > Production & Repair > Sale 020080 Electrical Engineering Tools in your PocketA set of 8 credit card-size, flexible cards packed with reference data all electronics designers need easy and instant access to. Whether you reverse-engineer an SMD board, figure out component values, or decide your best way to have a PCB manufactured, these gold plated cards provide instant technical guidance at real-life size for all aspects of PCB design state and electronics in general.There are 7 cards covering over 16 measurement techniques, over 100 schematic symbols, 2 value calculators (C, R), over 132 SMD footprints, 8 electronics laws & theory, and a powerful PCB design aid showing actual copper thickness, plating and finishing methods, track widths, and more. Plus, there’s an Elektor card showing their distinctive and legacy schematic drawing style and component symbols. To complete the set, there’s an Elektor cover card magnifying card for close inspection of PCB traces and SMD parts.Set comprises:9 cards (flexible, 80 x 50 x 0.6 mm, 18K gold-plating)1 Magnifying card1 Carabiner key ring1 Leather sleeve / pouch https://www.elektor.com/cdn/shop/files/elektor-cheatkard.jpg?v=1689093044https://www.elektor.com/cdn/shop/files/elektor-cheatkard_sleeve.jpg?v=1696854925,https://www.elektor.com/cdn/shop/files/elektor-cheatkard_cards.jpg?v=1696854925https://www.elektor.com/products/elektor-cheatkard-electrical-engineering-reference-cards?variant=46907280130380 in stock 34.95 29.95 36 4.9 6.9 2 - 4 Werktage 47666407473484 Elektor Circuit Special 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) > NEW EP-0523 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Tiny Solar SupplySunlight In, 3.3 V OutSolid-State Stereo Audio SwitchFree of Clicks and Moving PartsLarge RGB DigitWith Through-Hole WS2812 LEDsMicrophone Preamplifier with 48-V Phantom Power DistributionGreat for Podcasting and Pro AudioSquare Wave Generators with Duty Cycle and Frequency ControlsSimple Circuits with CMOS and TTL ICsSimple Dynamic CompressorWith Soft Control and Warm SoundSimple Electronic LockActive RectifierA solution or 2…40 V at up to 3 A with Reverse Current SuppressionOn / Off Switching System for Active BoxesUnbalanced/Balanced ConverterWith RFI Filter and DC Protection2023: An AI OdysseyWhere Did It Come From? Where Is It Going?Speed Controller for Fan or VentilatorWith Manual and Thermostat ModesThe Latest from Arduino Project HubNew Projects from the CommunityPower Overload MonitorMonitor Power Lines for Excessive CurrentBlink in the Dark Without TransistorsAn Oscillator with Only Two-Terminal PartsMorse Code GeneratorUse It as Beacon or Learning Device!Programmable Video DACHandles Any Format up to RGB888A T(eeny) Tiny PianoWithout Moving PartsDual Dice without MCUDual Dice on a Single PCB – Plus Some Design TricksElectronic ScarecrowCircuits to Amuse, Inspire, and AmazeLC-LP-HA ThermometerAccurate Measurements and a Binary DisplayTHD GeneratorGenerating Distortion on PurposeThyristor-Based Overtemperature IndicatorElectronic Components Used UnconventionallyPTC Fuse Flip-FlopFunny BirdA Chirping Elektor ClassicNeon Lamp with a MicrocontrollerTemperature-Stabilized IC Current SourceNeutralizing the Temperature Drift of Integrated Current SourcesSecond-Order Adjustable Treble BoostA Special Hearing Aid for the ElderlyEdwin Comes HomeA Look Back After 53 YearsOne-Armed BanditA Simple, Fun, Nostalgic, and Educational Elektor Classic!Simple Digitally Controlled Variable ResistorWater Leak ProtectionSafeguard and Alarm for Water LeaksEco-Timer with Auto-ShutdownNeeds 0.0 mW in Off Mode!ChatGPT and ArduinoZD MeterMeasuring Z Voltages of Z Diodes ≤ 100 VServo TesterESP32 Windows Controller with Free SoftwareAnalog and Mixed-Signal ICs by MicrochipLow-Consumption Power Management and Signal ProcessingInterface StandardsFilter and Surge Protection for the I²C BusLi-Ion Battery MonitorResidual Charge Indicator Provides Visual FeedbackPS/2 Mouse As Rotary Encoder (and More…)Simple Twilight Switchfor Retrofitting Lamps or InstallationsWater Pump ControllerPrepare Yourself Against Rising Water LevelsSolar-Powered Christmas FM Radio BallAll You Want for Christmas Is ThisVibration Sensor with RelayTap or Shake to Switch OnContinuity TesterSensitive and UnintrusivePower On/Off with a PushbuttonMini-Drill Power Control 2023A Revision of a Design from 1980Digital Vibration SensorTurn Vibrations into Precisely Timed PulsesReverse-Polarity Protection with Low Voltage DropA Low-Cost Frequency StandardTiny DCF77 SimulatorAn Accurate Fake-Time StandardThe Lilygo T-PicoC3Combines RP2040 and ESP32-C3 with Full Color-TFT Display https://www.elektor.com/cdn/shop/files/elektor-circuit-special-2023-en.png?v=1707314318https://www.elektor.com/products/elektor-circuit-special-2023-en?variant=47666407473484 in stock 10.95 38 4.9 6.9 2 - 4 Werktage 47666407965004 Elektor Circuit Special 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666407965004-has-digital-downloads ED-0523 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Tiny Solar SupplySunlight In, 3.3 V OutSolid-State Stereo Audio SwitchFree of Clicks and Moving PartsLarge RGB DigitWith Through-Hole WS2812 LEDsMicrophone Preamplifier with 48-V Phantom Power DistributionGreat for Podcasting and Pro AudioSquare Wave Generators with Duty Cycle and Frequency ControlsSimple Circuits with CMOS and TTL ICsSimple Dynamic CompressorWith Soft Control and Warm SoundSimple Electronic LockActive RectifierA solution or 2…40 V at up to 3 A with Reverse Current SuppressionOn / Off Switching System for Active BoxesUnbalanced/Balanced ConverterWith RFI Filter and DC Protection2023: An AI OdysseyWhere Did It Come From? Where Is It Going?Speed Controller for Fan or VentilatorWith Manual and Thermostat ModesThe Latest from Arduino Project HubNew Projects from the CommunityPower Overload MonitorMonitor Power Lines for Excessive CurrentBlink in the Dark Without TransistorsAn Oscillator with Only Two-Terminal PartsMorse Code GeneratorUse It as Beacon or Learning Device!Programmable Video DACHandles Any Format up to RGB888A T(eeny) Tiny PianoWithout Moving PartsDual Dice without MCUDual Dice on a Single PCB – Plus Some Design TricksElectronic ScarecrowCircuits to Amuse, Inspire, and AmazeLC-LP-HA ThermometerAccurate Measurements and a Binary DisplayTHD GeneratorGenerating Distortion on PurposeThyristor-Based Overtemperature IndicatorElectronic Components Used UnconventionallyPTC Fuse Flip-FlopFunny BirdA Chirping Elektor ClassicNeon Lamp with a MicrocontrollerTemperature-Stabilized IC Current SourceNeutralizing the Temperature Drift of Integrated Current SourcesSecond-Order Adjustable Treble BoostA Special Hearing Aid for the ElderlyEdwin Comes HomeA Look Back After 53 YearsOne-Armed BanditA Simple, Fun, Nostalgic, and Educational Elektor Classic!Simple Digitally Controlled Variable ResistorWater Leak ProtectionSafeguard and Alarm for Water LeaksEco-Timer with Auto-ShutdownNeeds 0.0 mW in Off Mode!ChatGPT and ArduinoZD MeterMeasuring Z Voltages of Z Diodes ≤ 100 VServo TesterESP32 Windows Controller with Free SoftwareAnalog and Mixed-Signal ICs by MicrochipLow-Consumption Power Management and Signal ProcessingInterface StandardsFilter and Surge Protection for the I²C BusLi-Ion Battery MonitorResidual Charge Indicator Provides Visual FeedbackPS/2 Mouse As Rotary Encoder (and More…)Simple Twilight Switchfor Retrofitting Lamps or InstallationsWater Pump ControllerPrepare Yourself Against Rising Water LevelsSolar-Powered Christmas FM Radio BallAll You Want for Christmas Is ThisVibration Sensor with RelayTap or Shake to Switch OnContinuity TesterSensitive and UnintrusivePower On/Off with a PushbuttonMini-Drill Power Control 2023A Revision of a Design from 1980Digital Vibration SensorTurn Vibrations into Precisely Timed PulsesReverse-Polarity Protection with Low Voltage DropA Low-Cost Frequency StandardTiny DCF77 SimulatorAn Accurate Fake-Time StandardThe Lilygo T-PicoC3Combines RP2040 and ESP32-C3 with Full Color-TFT Display https://www.elektor.com/cdn/shop/files/elektor-circuit-special-2023-pdf-en.png?v=1707314330https://www.elektor.com/products/elektor-circuit-special-2023-pdf-en?variant=47666407965004 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47310493352268 Elektor Circuit Special 2023 PDF (NL) Elektor Digital Magazines/Specials Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-47310493352268-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Mini-zonnevoedingzon in, 3,3 V uitSolid-state stereo-audioschakelaarklikvrij en zonder bewegende onderdelenGrote RGB-digitmet through-hole WS2812 LED’sMicrofoon-voorversterker met 48V-fantoomvoedingvoor podcasting en pro-audioBlokgolfgeneratoren met regelbare duty cycle en frequentiesimpele schakelingen met CMOS- en TTL-IC’sEenvoudige dynamiekcompressorsofte aansturing, warm geluidSimpel elektronisch slotActieve gelijkrichtervoor 2...40 V bij maximaal 3 A met tegenstroomonderdrukkingActieve boxen in- en uitschakelenOngebalanceerd/gebalanceerd-convertermet RF-filter en DC-bescherming2023: een AI-odysseewaar komt het vandaan en waar gaat het naar toe?Snelheidsregelaar voor ventilatormet handmatige en thermostaatmodusLaatste nieuwtjes van Arduino Project Hubnieuwe projecten uit de communityOverbelastingsmonitorbewaakt netsnoerenTransistorloos knipperlicht in het donkeroscillator met alleen tweedraads onderdelenMorsecode-generatorvoor gebruik als baken of leermiddel!Programmeerbare video-DACvoor elk formaat tot RGB888Kleintje klavierzonder bewegende onderdelenDubbel-dobbel zonder microprocessordubbele dobbelsteen op een enkele print – plus enkele ontwerptrucsElektronische vogelverschrikkerAmusante, inspirerende en verbazingwekkende schakelingenLC/LP/HA-thermometernauwkeurige metingen en een binair displayTHD-generatorvervorming, maar dan opzettelijkOvertemperatuur-indicator met thyristorelektronische onderdelen ongebruikelijk gebruiktEen PTC-flipflopSociale vogeleen tsjilpende Elektor KlassiekerNeonlamp plus microcontrollerTemperatuurgestabiliseerde IC-stroombronneutraliseer de temperatuurdrift van deze driebenersRegelbare tweede-orde hogetonen-boostergehoorsteuntje voor ouderenEdwin komt naar huisherinneringen na 53 jaarEénarmige bandieteen eenvoudige, leuke, nostalgische en leerzame Elektor-klassieker!Eenvoudige digitaal gestuurde variabele weerstandLekdetectorbeveiligt en alarmeert bij lekkagesEco-timer met automatische uitschakelingverbruikt niets in uitgeschakelde toestand!ChatGPT en ArduinoZenermetermeet de Z-spanning van Z-diodes ≤ 100 VServotesterESP32 Windows-controller met gratis softwareAnaloge en mixed-signal IC’s van Microchipzuinige signaalverwerkingInterfacenormenfilter en overspanningsbeveiliging voor de I²C-busLi-Ion accumonitorrestlading-indicator geeft visuele feedbackPS/2-muis als draai-encoder (en meer...)Simpele schemerschakelaarvoor bestaande lampen of installatiesController voor waterpompbereid je voor op hoogwaterKerstbal met FM-zonneradiomeer heb je voor de kerst niet nodigTrillingssensor met relaistik of schud om in te schakelenDoorgangstestergevoelig en niet storendIn- en uitschakelen met een drukknopRegeling voor mini-boor (2023)een ontwerp uit 1980 herzienDigitale trillingssensorzet trillingen om in nauwkeurig getimede pulsenOmpoolbeveiliging met kleine spanningsvalGoedkope frequentiestandaardKleine DCF77-simulatornauwkeurige fake-tijdstandaardDe Lilygo T-PicoC3combineert RP2040 en ESP32-C3 met een full-color TFT-displayHexadoku https://www.elektor.com/cdn/shop/files/elektor-circuit-special-2023-pdf-nl.png?v=1699287316https://www.elektor.com/products/elektor-circuit-special-2023-pdf-nl?variant=47310493352268 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47310493483340 Elektor Circular Christmas Tree Kit Elektor Labs Boards&Kits Arduino Kits > Elektor Kits > ESP32 > Fun Electronics > No Member Discount 7442105132171 DIY 3D Programmable Light Effects This Arduino-based Christmas Tree Kit contains 36 digitally programmable 8 mm RGB LEDs (WS2812D-F8) that are individually addressable for creating impressive light effects. The LEDs can be controlled externally or by an Arduino Nano ESP32. Features 36 digital RGB LEDs (NeoPixel-addressable) Suitable for any microcontroller system Perfect match with Arduino Nano ESP32 (not included) High-quality PCBs: 5x circular, 1x square Easy, fun assembly with popular tools Detailed construction manual Dimensions: 136 x 136 x 175 mm Included PCB (136 x 136 mm) Resistors R1…R36 = 75 #, 0W125, 5%, SMD 0805 P1 = 10 k#, 0W1, 20%, trimmer, top adjust, 6 mm round (Piher PT6KV-103A2020) Capacitors C1…C36 = 100 n, 50 V, 5%, X7R, SMD 0805 C37, C38 = 47u, 6V3, 10%, tantalum, case size A (1206) Semiconductors D1, D2 = S5J-E3/57T, SMD case size SMC LED1-LED36 = WS2812D-F8, 8 mm, THT Others K1, JP1 = Pin header, 3x1, vertical, 2.54 mm pitch Shunt jumper for JP1, 2.54 mm spacing K2 = MJ-179PH (Multicomp Pro), DC power connector, 4 A, pin diam. 1.95 mm S1 = DIP switch, 4-way PA1…PE6 = 2 m wire, 0.81 mm solid, 0.52 mm² / 20AWG, insulated green (Alpha Wire 3053/1 GR005) H1…H5 = Nylon standoff, female-female, M3, 5 mm H1…H5 = Nylon screw, M3, 5 mm Optional Arduino Nano ESP32 with Headers Links Elektor Labs https://www.elektor.com/cdn/shop/files/Elektor-Circular-Christmas-Tree-Kit.jpg?v=1701706899https://www.elektor.com/cdn/shop/files/Elektor-Circular-Christmas-Tree-Kit-front.jpg?v=1701706904,https://www.elektor.com/cdn/shop/files/Elektor-Circular-Christmas-Tree-Kit_pcb.jpg?v=1701706910,https://www.elektor.com/cdn/shop/files/Elektor-Circular-Christmas-Tree-Kit_contents.jpg?v=1701706915https://www.elektor.com/products/elektor-circular-christmas-tree-kit?variant=47310493483340 out of stock 29.95 24.95 0 4.9 6.9 nicht auf Lager 47318766387532 Elektor Cloc 2.0 Kit Elektor Labs Boards&Kits Bestsellers > Elektor Products 7442105132102 ESP32-based Alarm Clock connects to Timeserver and controls Radio & TV Cloc is an easy to build alarm clock without SMT parts. It has a double 7-segment retro display with variable brightness. One display shows the current time, the other the alarm time. Cloc connects to a Wi-Fi network, so it can access a timeserver somewhere on the planet. It can connect using DHCP or with a fixed IP address. An optional DS3231-based battery-backed real-time clock (RTC) module (not included in the kit) can be added to keep time in case of network problems. The built-in web server shows the time, allows setting the alarms and lets you adjust the clock’s parameters. The optimized graphical HTML interface works on most standard browsers and handheld devices. Specifications Based on an ESP32-Pico-Kit. Two independent 7-segment displays for the time of day and the alarm time. The time is set automatically by connecting to an online timeserver. Alarm time for each day of the week. Alarm output: buzzer and infrared code for e.g. radio, hi-fi system or TV. Two push-buttons for interacting with the device. Integrated web server for remote configuration via Wi-Fi. All settings are saved in EEPROM. Open-source software written for Arduino. Over-the-Air (OTA) mode allows updating the firmware remotely. Optional DS3231-based real-time clock (RTC) module (not included). Included PCB All components ESP32-Pico-Kit V4 (valued at €20) Hammond IR Red Translucent PC Enclosure (valued at €15) Links Cloc – Alarm Clock 2.0 https://www.elektor.com/cdn/shop/files/alarm-clock-2-top.jpg?v=1699544463https://www.elektor.com/cdn/shop/files/alarm-clock-2-right.jpg?v=1699544463,https://www.elektor.com/cdn/shop/files/alarm-clock-2-left.jpg?v=1699544463,https://www.elektor.com/cdn/shop/files/alarm-clock-2-parts-bagged.jpg?v=1699544463,https://www.elektor.com/cdn/shop/files/alarm-clock-2-parts-unpacked.jpg?v=1699544463,https://www.elektor.com/cdn/shop/files/cloc-enclosure.jpg?v=1699544463,https://www.elektor.com/cdn/shop/files/esp32-pico-kit-v4_1.png?v=1699544463,https://www.elektor.com/cdn/shop/files/cloc-enclosure-with-board.jpg?v=1699544463https://www.elektor.com/products/elektor-cloc-2-0-kit?variant=47318766387532 in stock 74.95 19 0 6.9 2 - 4 Werktage 46907174617420 Elektor Dual DC LISN (150 kHz - 200 MHz) Eurocircuits Boards&Kits Analyzers > Bestsellers > Comparison Websites DE > Comparison Websites FR > Elektor Kits > Elektor Products > Measuring Tools > NEW > No Member Discount > Test & Measurement Comparison Websites 7442105130191 Measuring conducted emission is the simplest and most affordable method of getting some indication of whether a design can meet EMI/EMC requirements. A Line Impedance Stabilization Network (LISN) is an indispensable part of an EMC pre-compliance test setup. In cooperation with Würth Elektronik, Elektor has developed a 5 µH, 50 Ω Dual DC LISN that supports voltages up to 60 V and currents up to 10 A. The instrument measures RF interferences on both channels (the power supply) by means of 5-μH blocking inductances. The internal 10-dB attenuation network – one in each channel – contains a 3rd-order high-pass filter with a cutoff frequency of 9 kHz to protect the input of instruments like a spectrum analyzer from potentially harmful DC voltages or low frequencies coming from the EUT (Equipment Under Test). Specifications RF path Channels 2 (with clamping diodes) Bandwidth 150 kHz – 200 MHz Inductance 5 μH || 50 Ω Internal attenuation 10 dB Connectors SMA DC path Max. current < 10 ADC Max. voltage < 60 VDC DC resistance < 2 x 70 mΩ PCB size 94.2 x 57.4 mm Connectors 4-mm banana Hammond enclosure Type 1590N Dimensions 121 x 66 x 40 mm Included 1x 4-layer PCB with all SMT parts fitted 1x pre-drilled enclosure with ready-printed front panel layout 5x gold-plated, insulated, 4-mm banana sockets, rated for 24 A, 1 kV 1x Hammond enclosure 1590N1, Aluminum (Die-Cast Alloy) More Info Project on Elektor Labs: Dual DC LISN for EMC pre-compliance testing Elektor 9-10/2021: EMC Pre-Compliance Test for Your DC-Powered Project (Part 1) Elektor 11-12/2021: EMC Pre-Compliance Test for Your DC-Powered Project (Part 2) https://www.elektor.com/cdn/shop/files/elektor-dual-dc-lisn-150-khz-200-mhz.jpg?v=1689089350https://www.elektor.com/cdn/shop/files/elektor-dual-dc-lisn-150-khz-200-mhz-front.jpg?v=1696852472,https://www.elektor.com/cdn/shop/files/elektor-dual-dc-lisn-150-khz-200-mhz_pcb-front.jpg?v=1696852472,https://www.elektor.com/cdn/shop/files/elektor-dual-dc-lisn-150-khz-200-mhz_measurement.jpg?v=1698679265,https://www.elektor.com/cdn/shop/files/elektor-dual-dc-lisn-150-khz-200-mhz_hammond-case.jpg?v=1698679266https://www.elektor.com/products/elektor-dual-dc-lisn-150-khz-200-mhz?variant=46907174617420 in stock 139.95 114.95 83 0 0 2 - 4 Werktage 46906983678284 Elektor ESP32 Smart Kit Elektor Labs Bundels Bestsellers > Elektor Kits > Elektor Products > ESP > ESP32 018305 This hardware kit is especially prepared for 'The Official ESP32 Book'. The kit contains all the components used in the projects in this book. With the help of this hardware kit it should be easy and fun to build the projects in the book. Included 1x ESP32 DevKitC 8x LEDs (RED) 1x LED (GREEN) 2x push-button 8x 330 ohm resistors 1x Buzzer 1x RGB LED 1x TMP36 temperature sensor chip 1x DHT11 temperature and humidity chip 1x MCP23017 (DIL 28 package) 1x LDR 1x BC108 (or any other PNP) transistor 1x 7 segment LED 1x Small Microphone Module 1x I²C LCD 1x SG90 servo 1x 4x4 Keypad 8x Female-Male jumpers 4x Male-Male jumpers 1x Small breadboard https://www.elektor.com/cdn/shop/files/elektor-esp32-smart-kit-18305.jpg?v=1698679272https://www.elektor.com/cdn/shop/files/esp32-book-kit-elektor.png?v=1698679272,https://www.elektor.com/cdn/shop/files/elektor-esp32-smart-kit-18305-no-box.png?v=1698679272https://www.elektor.com/products/elektor-esp32-smart-kit?variant=46906983678284 in stock 59.95 25 0 6.9 2 - 4 Werktage 46907037778252 Elektor ESP32 Smart Kit Bundle Elektor Bundles Bundels Bestsellers > Books > Bundles > ESP > ESP Books > No Member Discount 7442105128112 Experimenting with the ESP32 has never been easier! With the Elektor ESP32 Smart Kit Bundle, you'll learn programming with the ESP32 IoT Microcontroller using the Arduino IDE and MicroPython programming languages. The kit consists of the highly popular ESP32 DevKitC development board, breadboard, sensors, LEDs, LCD, etc. for use in experiments. The book provides basic and intermediate level projects. All projects have been tested and work. Block diagrams, circuit diagrams, and complete program listings of all projects are given with explanations. About the book: The main aim of this book is to teach the Arduino IDE and MicroPython programming languages in ESP32 based projects, using the highly popular ESP32 DevKitC development board. Many simple, basic, and intermediate level projects are provided in the book using the Arduino IDE with ESP32 DevKitC. All projects have been tested and work. Block diagrams, circuit diagrams, and complete program listings of all projects are given with explanations. In addition, several projects are provided for programming the ESP32 DevKitC using MicroPython. The kit consists of: 1x ESP32 DevKitC 8x LEDs (RED) 1x LED (GREEN) 2x push-button 8x 330 ohm resistors 1x Buzzer 1x RGB LED 1x TMP36 temperature sensor chip 1x DHT11 temperature and humidity chip 1x MCP23017 (DIL 28 package) 1x LDR 1x BC108 (or any other PNP) transistor 1x 7 segment LED 1x Small Microphone Module 1x I²C LCD 1x SG90 servo 1x 4x4 Keypad 8x Female-Male jumpers 4x Male-Male jumpers 1x Small breadboard https://www.elektor.com/cdn/shop/files/elektor-esp32-smart-kit-bundle.png?v=1689086043https://www.elektor.com/cdn/shop/files/the-complete-esp32-projects-guide_2.png?v=1696850238,https://www.elektor.com/cdn/shop/files/elektor-esp32-smart-kit.png?v=1696850238https://www.elektor.com/products/elektor-esp32-smart-kit-bundle?variant=46907037778252 in stock 69.95 54.95 11 0 6.9 2 - 4 Werktage 46907234451788 Elektor Fortissimo-100 Power Amplifier Kit Eurocircuits Boards&Kits Elektor Kits > Elektor Products 7442105131174 Celebrated Elektor audio design specialist Ton Giesberts has once again released a phenomenal design for a high-end audio power amplifier, the Elektor Fortissimo-100. Once again, the results of the amplifier on the test bench challenged Elektor’s high-spec Audio Precision test gear close to its noise floor. The specifications, ease of construction, and the overall stability of the Fortissimo-100 are deemed so good that Elektor are offering the project as a kit of parts for assembly at home, using plain tools. The kit contains each and every part to build one Fortissimo-100 mono block, including a set of high-quality PCBs, the heatsink, and other mechanical parts like standoffs and ceramic isolation washers for the power transistors. Again, all parts are through-hole. A detailed, step-by-step assembly guide (downloadable PDF) should enable every audio lover with the ability to work accurately and sensibly, to assemble the mono block and ravish at the sound quality. Two mono blocks are required to build a Fortissimo-100 stereo amplifier, plus a symmetrical 40-V, stabilized power supply per amplifier. Don’t use a single power supply for two amplifiers! The supply is not included in the kit, but a suggested source is given in the description for the project, so readers can opt for their personal desires. Specifications Input Sensitivity 1.076 V (94 W/8 Ω, THD = 0.1%, B = 22 kHz) Input Impedance 10 kΩ Sine-wave Power 94 W (8 Ω, THD = 0.1%) 181 W (4 Ω, THD = 0.1%) Bandwidth 3.3 Hz – 237 kHz (–3 dB, 1 W/8 Ω) Open-loop Bandwidth ≈ 20 kHz Open-loop Gain ≈ 140000 (8 Ω load) Slew Rate 45 V/μs Signal-to-Noise Ratio 103 dB (B = 22 Hz – 22 kHz linear) Harmonic Distortion Plus Noise 0.0008% (1 kHz, 50 W, 8 Ω, B = 80 kHz)0.002% (20 kHz, 50 W, 8 Ω, B = 80 kHz)0.0042% (20 kHz, 100 W, 4 Ω, B = 80 kHz) Intermodulation Distortion(50 Hz : 7 kHz = 4 : 1) 0.0015% (50 W, 8 Ω)0.0041% (100 W, 4 Ω) Included Two PCBs: amplifier PCB and protection PCB All parts, including heatsinks Construction Manual – Downloadable PDF Elektor Jumpstarter This product is the result of a successful campaign on our electronics project support platform Elektor Jumpstarter. Readers and interested parties can submit their product ideas and, together with the Elektor development team, a finished product can be brought to market after extensive consideration and many tests. Note that these are always small series production runs, so the products are considered 'Elektor Collector Items'. https://www.elektor.com/cdn/shop/files/01_fortissimo-100_intro_manual.jpg?v=1689091435https://www.elektor.com/cdn/shop/files/03_finished_2.jpg?v=1696854033,https://www.elektor.com/cdn/shop/files/04_pcbs_fortissimo-100_kit.jpg?v=1696854033,https://www.elektor.com/cdn/shop/files/05_resistors_small_capacitors.jpg?v=1698679295,https://www.elektor.com/cdn/shop/files/06_electrolytic_capacitors.jpg?v=1698679295,https://www.elektor.com/cdn/shop/files/07_small_transistors_diodes_more.jpg?v=1698679295,https://www.elektor.com/cdn/shop/files/08_large_transistors_proto_kit.jpg?v=1698679296,https://www.elektor.com/cdn/shop/files/09_ceramic_pads_relay_proto_kit.jpg?v=1698679295,https://www.elektor.com/cdn/shop/files/10_mechanical_parts_complete2.jpg?v=1698679296,https://www.elektor.com/cdn/shop/files/screenshot_2022-09-28_at_16.32.49.png?v=1698679296https://www.elektor.com/products/elektor-fortissimo-100-power-amplifier-kit?variant=46907234451788 out of stock 249.0 0 0 0 nicht auf Lager 47318771728716 Elektor Funny Bird Kit Elektor Labs Boards&Kits Bestsellers > Elektor Products > NEW > No Member Discount > Sale 7442105132133 Whistle And It Chirps Back At You! Although birds of all sorts are lovingly owned and watched by many people, sadly most of them have not yet learnt to communicate with us. This all-electronic bird takes a step in the right direction: when you whistle at it, it chirps back! Features Responds to Whistling Adjustable Bird Sounds (Tone and Length) Elektor Heritage Circuit Symbols Tried & Tested by Elektor Labs Educational & Geeky Project Through-Hole Parts Only Included Printed Circuit Board All Components Wooden Stand Bill of Materials Resistors R1,R2 = 2.2kΩ R3,R4,R13 = 47kΩ R5 = 4.7kΩ R6 = 3.3kΩ R7,R10,R11,R12,R17 = 100kΩ R8,R19,R23 = 1kΩ R9 = 1MΩ R14,R15 = 10kΩ R16,R18 = 470kΩ R20 = 68kΩ R21 = 10MΩ R22 = 2.7kΩ R24 = 22Ω P1,P2 = 1MΩ P3,P5 = 470kΩ P4 = 100kΩ Capacitors C1,C2,C12 = 100nF C3,C4 = 10nF C5 = 22μF, 16V C6,C7,C11 = 10μF, 16V C8 = 2.2μF, 100V C9 = 1μF, 50V C10 = 2.2nF C13 = 10nF Semiconductors D1,D3,D4,D5,D6,D7,D8 = 1N4148 D2 = 3V3 zener diode T1,T2 = BC557B T3 = BC547B T4 = BC327-40 IC1 = TL084CN IC2 = 4093 Miscellaneous BT1 = wired battery clip for 6LR61/PP3 LS1 = miniature loudspeaker, 8Ω, 0.5W S1 = switch, slide, SPDT MIC1 = electret microphone PCB 230153-1 v1.1 https://www.elektor.com/cdn/shop/files/elektor-funny-bird-kit.png?v=1699464721https://www.elektor.com/cdn/shop/files/elektor-funny-bird-kit_package.png?v=1699544576https://www.elektor.com/products/elektor-funny-bird-kit?variant=47318771728716 in stock 44.95 37.95 102 4.9 6.9 2 - 4 Werktage 46907274527052 Elektor Januari/Februari 2022 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0669 MOTOREN AANSTUREN MET H-BRUGGENeen inleiding tot gelijkstroom-, stappen- en borstelloze motoren HET ELEKTOR LAB-TEAMonze aanpak, onze tools – en meer... RASPBERRY PI ALS KVM-AFSTANDSBEDIENINGsoftwaretest Pi-KVM IQAUDIO CODEC ZEROgeluidskaart voor de Raspberry Pi-familie WAT WE KUNNEN LEREN VAN HET PIKVM-PROJECTeen vraaggesprek met Maxim Devaev AUTONOOM RIJDEN MET 2D-LIDARESP32 Pico interpreteert gegevens van de lidar-module DE RASPBERRY PI ZERO 2 W GAAT QUAD-CORE NOTITIES BIJ VAN HET WORLD ETHICAL ELECTRONICS FORUM 2021 MOTORBESTURINGhoe de complexiteit van motorbesturing wordt gereduceerd GROTE ELEKTROMOTORENbasisprincipes en nuttige informatie AAN DE SLAG MET DE ESP32-C3 RISC-V MCU BESCHERM UZELF EN ANDEREN!DHZ-hoofdschakelaar voor uw werkbank GUI'S MAKEN MET PYTHON (DEEL 2)Spionnennaamkiezer PRODUCTRONICA FAST FORWARD 2021: DE WINNAARSspannende technologieën en creatieve engineeringoplossingen VEELZIJDIGE SERVOTESTERcontroleer het gedrag, ook zonder datasheet MODBUS VIA WLANdeel 2: software voor de Modbus TCP WLAN-module KENNISMAKING MET NEURONEN IN NEURALE NETWERKENdeel 3: neuronen in de praktijk IN EEN OPEN SOURCE-PROCESSORvoorbeeldhoofdstuk: vergelijking van Lattice- en Xilinx-FPGA’s ALLE BEGIN......is nog niet klaar met de spoel PROJECT 2.0correcties, updates en brieven van lezers KLEUR NAAR GELUIDeen kleursensor via I2C uitlezen BATTLAB-ONEmeet en optimaliseer de gebruiksduur van IoT-accu’s EENVOUDIGE AARDLEKTESTERisolatietest voor lichtnetinstallaties ARMOEDE EN ELEKTRONICAhet streven naar duurzame ontwikkeling HEXADOKUpuzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-01-02-2022_nl.png?v=1689092863https://www.elektor.com/products/elektor-januari-februari-2022-nl?variant=46907274527052 in stock 14.95 35 4.9 6.9 2 - 4 Werktage 46907266892108 Elektor Januari/Februari 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907266892108-has-digital-downloads MOTOREN AANSTUREN MET H-BRUGGENeen inleiding tot gelijkstroom-, stappen- en borstelloze motoren HET ELEKTOR LAB-TEAMonze aanpak, onze tools – en meer... RASPBERRY PI ALS KVM-AFSTANDSBEDIENINGsoftwaretest Pi-KVM IQAUDIO CODEC ZEROgeluidskaart voor de Raspberry Pi-familie WAT WE KUNNEN LEREN VAN HET PIKVM-PROJECTeen vraaggesprek met Maxim Devaev AUTONOOM RIJDEN MET 2D-LIDARESP32 Pico interpreteert gegevens van de lidar-module DE RASPBERRY PI ZERO 2 W GAAT QUAD-CORE NOTITIES BIJ VAN HET WORLD ETHICAL ELECTRONICS FORUM 2021 MOTORBESTURINGhoe de complexiteit van motorbesturing wordt gereduceerd GROTE ELEKTROMOTORENbasisprincipes en nuttige informatie AAN DE SLAG MET DE ESP32-C3 RISC-V MCU BESCHERM UZELF EN ANDEREN!DHZ-hoofdschakelaar voor uw werkbank GUI'S MAKEN MET PYTHON (DEEL 2)Spionnennaamkiezer PRODUCTRONICA FAST FORWARD 2021: DE WINNAARSspannende technologieën en creatieve engineeringoplossingen VEELZIJDIGE SERVOTESTERcontroleer het gedrag, ook zonder datasheet MODBUS VIA WLANdeel 2: software voor de Modbus TCP WLAN-module KENNISMAKING MET NEURONEN IN NEURALE NETWERKENdeel 3: neuronen in de praktijk IN EEN OPEN SOURCE-PROCESSORvoorbeeldhoofdstuk: vergelijking van Lattice- en Xilinx-FPGA’s ALLE BEGIN......is nog niet klaar met de spoel PROJECT 2.0correcties, updates en brieven van lezers KLEUR NAAR GELUIDeen kleursensor via I2C uitlezen BATTLAB-ONEmeet en optimaliseer de gebruiksduur van IoT-accu’s EENVOUDIGE AARDLEKTESTERisolatietest voor lichtnetinstallaties ARMOEDE EN ELEKTRONICAhet streven naar duurzame ontwikkeling HEXADOKUpuzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-01-02-2022-pdf_nl.png?v=1689092659https://www.elektor.com/products/elektor-januari-februari-2022-pdf-nl?variant=46907266892108 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 46907276296524 Elektor Januari/Februari 2023 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0677 Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Voor ogen en orenVideo-output met microcontrollers (1)Composiet Videoelectronica 2022nieuws van 's werelds grootste elektronicabeursESP32-camerazo simpel – heeft niet eens WiFiATX-voeding voor Raspberry Pi32 Ω KoptelefoonversterkerEenvoudige maar hoogwaardige 3-chip oplossingSDR-radioklokkenvijf tijdsignalen, zes displaysAlle begin......zet een streep onder de diodeUit het leven gegrepenover de kwaliteit der dingenReverse-engineering van een Bluetooth Low Energy LED-badgeeen BLE-apparaat besturen met een Python-scriptMakePython ESP32 Development KitAlles in een doosjeTHD-meting met een oscilloscoop en FFTgemakkelijke berekening van de vervormingsfactorAllesziende machinesde technologie achter moderne industrële visionsystemenInfographicsDe evolutie van spraak- en audiogestuurde elektronische apparatenWEEF 2022 terugblikFFWD elektronica 2022 terugblikde vernieuwers hebben niet nagelaten indruk te makenThe Tubeeen ongebruikelijke buizenversterkerBiomateriaal in elektronica: klaar of nietDe Opera Cake antenne switch voor HackRF OneSluit tot acht antennes aan op uw SDREngineering met de Arduino, en meerEen interview met auteur Ashwin PajankarLiDAR-precisiemetermeet tot 12 meterAudiosignalen en de ESP32De ESP-ADF-omgeving in de praktijkElektor Fortissimo-100 einversterker-kitLichtgestuurde geluidseffectenSpanningsgestuurd 24 dB/oct synthesizerfilter (VCF) met LDR'sDe kilo-watter van Elektuurmeer volume gaat niet!Oost West Lab Besteen volumetrisch display in CanadaProject 2.0Correcties, Updates en Brieven van lezersHexadoku https://www.elektor.com/cdn/shop/files/elektor-01-02-2023_nl.png?v=1689092915https://www.elektor.com/products/elektor-januari-februari-2023-nl?variant=46907276296524 in stock 14.95 85 4.9 6.9 2 - 4 Werktage 46907268038988 Elektor Januari/Februari 2023 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907268038988-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Voor ogen en orenVideo-output met microcontrollers (1)Composiet Videoelectronica 2022nieuws van 's werelds grootste elektronicabeursESP32-camerazo simpel – heeft niet eens WiFiATX-voeding voor Raspberry Pi32 Ω KoptelefoonversterkerEenvoudige maar hoogwaardige 3-chip oplossingSDR-radioklokkenvijf tijdsignalen, zes displaysAlle begin......zet een streep onder de diodeUit het leven gegrepenover de kwaliteit der dingenReverse-engineering van een Bluetooth Low Energy LED-badgeeen BLE-apparaat besturen met een Python-scriptMakePython ESP32 Development KitAlles in een doosjeTHD-meting met een oscilloscoop en FFTgemakkelijke berekening van de vervormingsfactorAllesziende machinesde technologie achter moderne industrële visionsystemenInfographicsDe evolutie van spraak- en audiogestuurde elektronische apparatenWEEF 2022 terugblikFFWD elektronica 2022 terugblikde vernieuwers hebben niet nagelaten indruk te makenThe Tubeeen ongebruikelijke buizenversterkerBiomateriaal in elektronica: klaar of nietDe Opera Cake antenne switch voor HackRF OneSluit tot acht antennes aan op uw SDREngineering met de Arduino, en meerEen interview met auteur Ashwin PajankarLiDAR-precisiemetermeet tot 12 meterAudiosignalen en de ESP32De ESP-ADF-omgeving in de praktijkElektor Fortissimo-100 einversterker-kitLichtgestuurde geluidseffectenSpanningsgestuurd 24 dB/oct synthesizerfilter (VCF) met LDR'sDe kilo-watter van Elektuurmeer volume gaat niet!Oost West Lab Besteen volumetrisch display in CanadaProject 2.0Correcties, Updates en Brieven van lezersHexadoku https://www.elektor.com/cdn/shop/files/elektor-01-02-2023-pdf_nl.png?v=1689092708https://www.elektor.com/products/elektor-januari-februari-2023-pdf-nl?variant=46907268038988 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47475103990092 Elektor Januari/Februari 2024 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products has-digital-downloads,variant-47475103990092-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Project-update: ESP32-gebaseerde energiemeterwe gaan verder met het prototypeOptimalisatie van balkon PV-centralesoverwegingen, interessante feiten en berekeningenESP32 met OpenDTU voor balkoncentralesgegevens van kleine omvormers via MCU’s uitlezenRegelbare lineaire labvoeding0...50 V / 0...2 A + dubbele symmetrische voedingEnergieopslag – vandaag en morgeneen vraaggesprek met Simon Engelke2024: een AI-odysseehet houdt nog lang niet opBluetooth LE op de STM32meetwaarden op afstand uitlezenMensvriendelijk slim keuken-voorraadsysteemMAUI: programmeren voor PC, tablet en smartphonehet nieuwe framework in theorie en praktijkChatMagLevkunstmatig intelligente levitatieEenvoudige PV-regelaarbouw je eerste, volledig functionele PV-energiebeheersysteemKoude-kathode-buizenvreemde onderdelenUit het leven gegrepennostalgieAlle begin......bekijkt de FETCAN-bus voor de Arduino UNO R4: een tutorialtwee UNO R4’s nemen de bus!Elektor infographicvoeding en energieVergelijking van vermogensdichtheid en vermogensefficiëntieAluminium elektrolytische condensatorenstoringspotentieel in audiotechnologieUSB testen en metenmet de Fnirsi FNB58De Pixel Pump pick&place-tooleenvoudiger handmatige assemblage van SMT-printenOost West Lab Bestnog niet zo lang geleden, in een land heel ver van hier...“In de wereld van ethiek in elektronica kunnen zelfs kleine stappen een aanzienlijke invloed hebben.”Ethiek in elektronicade OECD Guidelines en het LieferkettensorgfaltspflichtengesetzChadèche: slimme NiMH-(ont)laderlezersproject in het kortProject 2.0correcties, updates en brieven van lezers https://www.elektor.com/cdn/shop/files/elektor-1-2-2024-pdf_nl.png?v=1703238283https://www.elektor.com/products/elektor-januari-februari-2024-pdf-nl?variant=47475103990092 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47571282985292 Elektor January/February 2020 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571282985292-has-digital-downloads - Elektor Magazine EN January/February 2020 (PDF) https://www.elektor.com/cdn/shop/files/elektor-01-02-2020-pdf_en.png?v=1705320003https://www.elektor.com/products/elektor-january-february-2020-pdf-en?variant=47571282985292 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47571283312972 Elektor January/February 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0505 Elektor Magazine EN January/February 2021 https://www.elektor.com/cdn/shop/files/elektor-01-02-2021_en.png?v=1705320014https://www.elektor.com/products/elektor-january-february-2021-en?variant=47571283312972 in stock 10.95 53 4.9 6.9 2 - 4 Werktage 47571285246284 Elektor January/February 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571285246284-has-digital-downloads - Elektor Magazine EN January/February 2021 (PDF) https://www.elektor.com/cdn/shop/files/elektor-01-02-2021-pdf_en.png?v=1705320025https://www.elektor.com/products/elektor-january-february-2021-pdf-en?variant=47571285246284 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666408554828 Elektor January/February 2022 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0511 DRIVING MOTORS WITH H-BRIDGESAn Introduction to DC, Stepper, and Brushless Motors THE ELEKTOR LAB TEAMOur Approach, Preferred Tools, and More RASPBERRY PI AS A KVM REMOTE CONTROLPi-KVM Software Test IQAUDIO CODEC ZEROA Sound Card for the Raspberry Pi Family THE PIKVM PROJECT AND LESSONS LEARNEDInterview with Maxim Devaev (Developer, PiKVM) AUTONOMOUS VEHICLE WITH 2D LIDARESP32 Pico Interprets Data from the Lidar Module THE RASPBERRY PI ZERO 2 W GOES QUAD-CORE NOTES FROM THE 2021 WORLD ETHICAL ELECTRONICS FORUM MOTOR CONTROLHow the Complexity of Motor Control Is Simplified LARGE ELECTRIC MOTORSBasic Principles and Useful Information GETTING STARTED WITH THE ESP32-C3 RISC-V MCU PROTECT YOURSELF AND OTHERS!DIY Master Power Switch for the Lab Bench CREATE GUIS WITH PYTHON (PART 2)Spy name chooser PRODUCTRONICA FAST FORWARD 2021 WINNERSExciting Technologies and Creative Engineering Solutions VERSATILE SERVO TESTERCheck Behavior When There’s No Datasheet MODBUS OVER WLAN (PART 2)Software for the Modbus TCP WLAN Module UNDERSTANDING THE NEURONS IN NEURAL NETWORKS (PART 3)Practical Neurons INSIDE AN OPEN-SOURCE PROCESSORSample Chapter: Lattice and Xilinx FPGA Results STARTING OUT IN ELECTRONICSWe Are Not Yet Done with the Coil ERR-LECTRONICSCorrections, Updates and Readers’ Letters COLOR TO SOUNDHow to Read Out a Color Sensor via I2C BATTLAB-ONEMeasure and Optimize the Battery Life of IoT Devices SIMPLE EARTH-LEAKAGE TRACERTesting Isolation of Mains Supply POVERTY AND ELECTRONICSSustainable Development Goal 1 HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-01-02-2022_en.png?v=1707314343https://www.elektor.com/products/elektor-january-february-2022-en?variant=47666408554828 in stock 10.95 107 4.9 6.9 2 - 4 Werktage 47666409439564 Elektor January/February 2022 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666409439564-has-digital-downloads - DRIVING MOTORS WITH H-BRIDGESAn Introduction to DC, Stepper, and Brushless Motors THE ELEKTOR LAB TEAMOur Approach, Preferred Tools, and More RASPBERRY PI AS A KVM REMOTE CONTROLPi-KVM Software Test IQAUDIO CODEC ZEROA Sound Card for the Raspberry Pi Family THE PIKVM PROJECT AND LESSONS LEARNEDInterview with Maxim Devaev (Developer, PiKVM) AUTONOMOUS VEHICLE WITH 2D LIDARESP32 Pico Interprets Data from the Lidar Module THE RASPBERRY PI ZERO 2 W GOES QUAD-CORE NOTES FROM THE 2021 WORLD ETHICAL ELECTRONICS FORUM MOTOR CONTROLHow the Complexity of Motor Control Is Simplified LARGE ELECTRIC MOTORSBasic Principles and Useful Information GETTING STARTED WITH THE ESP32-C3 RISC-V MCU PROTECT YOURSELF AND OTHERS!DIY Master Power Switch for the Lab Bench CREATE GUIS WITH PYTHON (PART 2)Spy name chooser PRODUCTRONICA FAST FORWARD 2021 WINNERSExciting Technologies and Creative Engineering Solutions VERSATILE SERVO TESTERCheck Behavior When There’s No Datasheet MODBUS OVER WLAN (PART 2)Software for the Modbus TCP WLAN Module UNDERSTANDING THE NEURONS IN NEURAL NETWORKS (PART 3)Practical Neurons INSIDE AN OPEN-SOURCE PROCESSORSample Chapter: Lattice and Xilinx FPGA Results STARTING OUT IN ELECTRONICSWe Are Not Yet Done with the Coil ERR-LECTRONICSCorrections, Updates and Readers’ Letters COLOR TO SOUNDHow to Read Out a Color Sensor via I2C BATTLAB-ONEMeasure and Optimize the Battery Life of IoT Devices SIMPLE EARTH-LEAKAGE TRACERTesting Isolation of Mains Supply POVERTY AND ELECTRONICSSustainable Development Goal 1 HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-01-02-2022-pdf_en.png?v=1707314354https://www.elektor.com/products/elektor-january-february-2022-pdf-en?variant=47666409439564 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666409832780 Elektor January/February 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0519 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.For Eyes and EarsVideo Output with Microcontrollers (1)Composite Videoelectronica 2022News from the world’s leading electronics trade showESP32 CameraSo Simple, It Doesn’t Even Have to Use Wi-FiATX Power Supply for Raspberry Pi32 Ω Headphone AmplifierSimple But High-Quality 3-Chip SolutionSDR Radio-Controlled clocksFive Time Signals, Six DisplaysStarting Out in ElectronicsSpecial DiodesFrom Life's ExperienceMusings on the Quality of ThingsReverse-Engineering a Bluetooth Low Energy LED BadgeHow to Control a BLE Device with a Python ScriptMakePython ESP32 Development KitEverything in a BoxTHD Measurement with an Oscilloscope and FFTEasily Calculate the Distortion FactorAll-Seeing MachinesThe Technology Behind Today’s Industrial Vision SystemsInfographicsThe Evolution of Voice and Audio Control for Electronic DevicesWEEF 2022 in ReviewFFWD electronica 2022 in ReviewInnovators Did Not Fail to ImpressThe TubeAn Unusual Tube AmplifierBiomaterial in Electronics: Ready or NotOpera Cake Antenna Switch for HackRF OneConnect Up To Eight Antennas To Your SDREngineering with Arduino and MoreAn Interview with Author Ashwin PajankarLiDAR Precision GaugeMeasure up to 12 MetersAudio Signals and the ESP32The ESP-ADF Environment in PracticeElektor Fortissimo-100 Power Amplifier KitUsing Light for Sound EffectsLDR-Based Voltage-Controlled 24 dB/oct Synthesizer FilterElektor High-Power AF AmplifierThe Loudest of Them All!HomeLab ToursA Volumetric Display Made in CanadaErr-lectronicsCorrections, Updates and Readers’ LettersHexadoku https://www.elektor.com/cdn/shop/files/elektor-01-02-2023_en.png?v=1707314366https://www.elektor.com/products/elektor-january-february-2023-en?variant=47666409832780 in stock 10.95 62 4.9 6.9 2 - 4 Werktage 47666410684748 Elektor January/February 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666410684748-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.For Eyes and EarsVideo Output with Microcontrollers (1)Composite Videoelectronica 2022News from the world’s leading electronics trade showESP32 CameraSo Simple, It Doesn’t Even Have to Use Wi-FiATX Power Supply for Raspberry Pi32 Ω Headphone AmplifierSimple But High-Quality 3-Chip SolutionSDR Radio-Controlled clocksFive Time Signals, Six DisplaysStarting Out in ElectronicsSpecial DiodesFrom Life's ExperienceMusings on the Quality of ThingsReverse-Engineering a Bluetooth Low Energy LED BadgeHow to Control a BLE Device with a Python ScriptMakePython ESP32 Development KitEverything in a BoxTHD Measurement with an Oscilloscope and FFTEasily Calculate the Distortion FactorAll-Seeing MachinesThe Technology Behind Today’s Industrial Vision SystemsInfographicsThe Evolution of Voice and Audio Control for Electronic DevicesWEEF 2022 in ReviewFFWD electronica 2022 in ReviewInnovators Did Not Fail to ImpressThe TubeAn Unusual Tube AmplifierBiomaterial in Electronics: Ready or NotOpera Cake Antenna Switch for HackRF OneConnect Up To Eight Antennas To Your SDREngineering with Arduino and MoreAn Interview with Author Ashwin PajankarLiDAR Precision GaugeMeasure up to 12 MetersAudio Signals and the ESP32The ESP-ADF Environment in PracticeElektor Fortissimo-100 Power Amplifier KitUsing Light for Sound EffectsLDR-Based Voltage-Controlled 24 dB/oct Synthesizer FilterElektor High-Power AF AmplifierThe Loudest of Them All!HomeLab ToursA Volumetric Display Made in CanadaErr-lectronicsCorrections, Updates and Readers’ LettersHexadoku https://www.elektor.com/cdn/shop/files/elektor-01-02-2023-pdf_en.png?v=1707314378https://www.elektor.com/products/elektor-january-february-2023-pdf-en?variant=47666410684748 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666411864396 Elektor January/February 2024 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Magazines has-digital-downloads,variant-47666411864396-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Project Update: ESP32-Based Energy MeterNext Steps in PrototypingOptimizing Balcony Power PlantsConsiderations, Interesting Facts, and CalculationsESP32 With OpenDTU for Balcony Power PlantsRead Data from Small Inverters Via MCUsVariable Linear Power Supply Ensemble0…50 V / 0…2 A + Dual Symmetrical SupplyEnergy Storage Today and TomorrowAn Interview With Simon Engelke2024: An AI OdysseyIt’s Not Letting UpBluetooth LE on the STM32A Way to Read Measurements RemotelyHuman-Centric Smart Kitchen Grocery ContainerMAUI: Programming for PC, Tablet, and SmartphoneThe New Framework in Theory and PracticeChatMagLevThe AI Way of LevitationSimple PV Power RegulatorBuild Your First, Fully Functional PV Energy Management SystemCold-Cathode DevicesPeculiar Parts, the SeriesFrom Life’s ExperienceNostalgiaStarting Out in Electronics……Looking at FETsCAN Bus Tutorial for the Arduino UNO R4Two UNO R4s Hop on the Bus!Infographics: Power & EnergyComprehensive Design and Development SupportArrow Engineering ServicesComparing Power Density and Power EfficiencyAluminium Electrolytic CapacitorsInterference Potential in Audio TechnologyUSB Test and MeasurementThe Fnirsi FNB58The Pixel Pump Pick-and-Place ToolSimplifying Manual SMT Board AssemblyHomeLab ToursNot So Long Ago, in a Far-Away Country...“In the world of ethics in electronics, even small steps can make a significant impact.”Ethics in ElectronicsThe OECD Guidelines and Germany’s Supply Chain Due Diligence ActChadèche: Smart Ni-MH Charger/DischargerA Reader’s Project in BriefErr-lectronicsCorrections, Updates and Readers’ Letters https://www.elektor.com/cdn/shop/files/elektor-1-2-2024-pdf_en.png?v=1707314402https://www.elektor.com/products/elektor-january-february-2024-pdf-en?variant=47666411864396 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 46907275280716 Elektor Juli/Augustus 2022 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0672 Goedkope audiotestermet PC-gebaseerde software en een USB-audio-interface AC-netfrequentiemeterbewaakt netfrequentie en -spanning Een kleine inductiemeterbetaalbare oplossing voor de werkbank Zweven op geluidsgolvende Makerfabs Acoustic Levitation Kit nader bekeken Alle begin......gaat gelijkrichten FFWD: de blik weer naar voren! Aan de slag met je oscilloscoopzo gebruik je de knoppen en schakelaars Een MSF-SDR met de Raspberry Pi Picodecodeer het tijdsignaal met een Pi Pico-SDR Bodemvochtsensoren voor beregeningssystemenautomatische beregening Onrust op de markt voor test- en meetapparatuurkleine spelers innoveren Elektor Infographics Inspiratie, daar draait het omInterview met Ondernemer Walter Arkesteijn, InnoFaith Beauty Sciences EMC-storingen door opslagspoelen minimaliseren GUI’s maken met Python:Boter-kaas-en-eieren Jeroen en Jan blijven pionieren Eenvoudige analoge ESR-metermet draaispoelmeter-precisie Sigfox CO2-stoplichtzonder WiFi-netwerk! Vrouwen in de techniek“Het gaat allemaal om verdienste tot verdienste tieten heeft” Low-budget tablet-oscilloscoop ADS1013Dwaar voor je geld? Anatomie van smart plugsWelke zijn hacker-vriendelijk? Huidimpedantie en huidcapaciteitexperimenteel onderzocht Uit het leven gegrepenGeen sant in eigen land De Pokit Meter bekekeneen Zwitsers zakmes onder de meetinstrumenten HexadokuPuzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-07-08-2022_nl.png?v=1689092885https://www.elektor.com/products/elektor-juli-augustus-2022-nl?variant=46907275280716 in stock 14.95 70 4.9 6.9 2 - 4 Werktage 46907267481932 Elektor Juli/Augustus 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907267481932-has-digital-downloads Goedkope audiotestermet PC-gebaseerde software en een USB-audio-interface AC-netfrequentiemeterbewaakt netfrequentie en -spanning Een kleine inductiemeterbetaalbare oplossing voor de werkbank Zweven op geluidsgolvende Makerfabs Acoustic Levitation Kit nader bekeken Alle begin......gaat gelijkrichten FFWD: de blik weer naar voren! Aan de slag met je oscilloscoopzo gebruik je de knoppen en schakelaars Een MSF-SDR met de Raspberry Pi Picodecodeer het tijdsignaal met een Pi Pico-SDR Bodemvochtsensoren voor beregeningssystemenautomatische beregening Onrust op de markt voor test- en meetapparatuurkleine spelers innoveren Elektor Infographics Inspiratie, daar draait het omInterview met Ondernemer Walter Arkesteijn, InnoFaith Beauty Sciences EMC-storingen door opslagspoelen minimaliseren GUI’s maken met Python:Boter-kaas-en-eieren Jeroen en Jan blijven pionieren Eenvoudige analoge ESR-metermet draaispoelmeter-precisie Sigfox CO2-stoplichtzonder WiFi-netwerk! Vrouwen in de techniek“Het gaat allemaal om verdienste tot verdienste tieten heeft” Low-budget tablet-oscilloscoop ADS1013Dwaar voor je geld? Anatomie van smart plugsWelke zijn hacker-vriendelijk? Huidimpedantie en huidcapaciteitexperimenteel onderzocht Uit het leven gegrepenGeen sant in eigen land De Pokit Meter bekekeneen Zwitsers zakmes onder de meetinstrumenten HexadokuPuzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-07-08-2022-pdf_nl.png?v=1689092680https://www.elektor.com/products/elektor-juli-augustus-2022-pdf-nl?variant=46907267481932 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47318781428044 Elektor Juli/Augustus 2023 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0680 Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Kiesschijftelefoon als afstandsbedieningvoor licht kies 1; voor koffie kies 2GPS-gebaseerde snelheidsmeternooit meer bekeuringenRGB-stroboscoop met Arduinokleurige toepassing van een nuttig instrumentDraadloze nooddrukknopmeer veiligheid met LoRaAlle begin......volgt de emitterVrij te kiezen onafhankelijke hystereseniveaus voor comparatorenmet simulaties, spreadsheets en algebraImpedantie-analyzer op basis van een ESP32simpel, weinig onderdelen en goedkoop!Oost West Lab Bestzelfbouw moet gestimuleerd!Het MCCAB Arduino Nano Training Boardalle hardware voor de “Microcontrollers Hands-On Course”Uit het leven gegrepenmodern luddismeSensor-ABC: de DS18B20 temperatuursensoraansluiting op de 1-Wire busGaan Matter en Thread het Smart Home redden?nieuwe standaarden om het slimme huis te vereenvoudigenEen kwestie van samenwerkingontwikkelen met het Thing Plus Matter Board en Simplicity StudioElektor IIIIinfographicIoT en sensorenMatter, ExpressLink, Rainmaker – waar hebben we het over?vraaggesprek met Amey Inamdar van EspressifDe juiste keuze van microcontroller-ontwikkelkitsvoor IoT- en IIoT-toepassingenCondensatoren gedragen zich niet altijd capacitief!Een NTP-klok met CircuitPythonwaarom zou je deze programmeertaal gebruiken?Bouw een cool IoT-display'met de Phambili NewtDe doppler-bewegingssensor HB100theorie en praktijkEen gids voor puristisch programmeren (deel 1)voor STM32 en andere controllersSiglent SDM3045X-multimeterMicroprocessoren voor embedded systemenvreemde onderdelenMicrocontroller-documentatie verklaarddeel 3: blokschema’s en meerLow-power LoRa-weerstationbouw zelf een weerstation met een groot bereikTransverter voor de 70cm-bandKlimaat aan ingenieurssnelheid is geboden!Hexadoku https://www.elektor.com/cdn/shop/files/elektor-07-08-2023_nl.png?v=1699465057https://www.elektor.com/products/elektor-juli-augustus-2023-nl?variant=47318781428044 in stock 14.95 18 4.9 6.9 2 - 4 Werktage 47318781329740 Elektor Juli/Augustus 2023 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-47318781329740-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Kiesschijftelefoon als afstandsbedieningvoor licht kies 1; voor koffie kies 2GPS-gebaseerde snelheidsmeternooit meer bekeuringenRGB-stroboscoop met Arduinokleurige toepassing van een nuttig instrumentDraadloze nooddrukknopmeer veiligheid met LoRaAlle begin......volgt de emitterVrij te kiezen onafhankelijke hystereseniveaus voor comparatorenmet simulaties, spreadsheets en algebraImpedantie-analyzer op basis van een ESP32simpel, weinig onderdelen en goedkoop!Oost West Lab Bestzelfbouw moet gestimuleerd!Het MCCAB Arduino Nano Training Boardalle hardware voor de “Microcontrollers Hands-On Course”Uit het leven gegrepenmodern luddismeSensor-ABC: de DS18B20 temperatuursensoraansluiting op de 1-Wire busGaan Matter en Thread het Smart Home redden?nieuwe standaarden om het slimme huis te vereenvoudigenEen kwestie van samenwerkingontwikkelen met het Thing Plus Matter Board en Simplicity StudioElektor IIIIinfographicIoT en sensorenMatter, ExpressLink, Rainmaker – waar hebben we het over?vraaggesprek met Amey Inamdar van EspressifDe juiste keuze van microcontroller-ontwikkelkitsvoor IoT- en IIoT-toepassingenCondensatoren gedragen zich niet altijd capacitief!Een NTP-klok met CircuitPythonwaarom zou je deze programmeertaal gebruiken?Bouw een cool IoT-display'met de Phambili NewtDe doppler-bewegingssensor HB100theorie en praktijkEen gids voor puristisch programmeren (deel 1)voor STM32 en andere controllersSiglent SDM3045X-multimeterMicroprocessoren voor embedded systemenvreemde onderdelenMicrocontroller-documentatie verklaarddeel 3: blokschema’s en meerLow-power LoRa-weerstationbouw zelf een weerstation met een groot bereikTransverter voor de 70cm-bandKlimaat aan ingenieurssnelheid is geboden!Hexadoku https://www.elektor.com/cdn/shop/files/elektor-07-08-2023-pdf_nl.png?v=1699465048https://www.elektor.com/products/elektor-juli-augustus-2023-pdf-nl?variant=47318781329740 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47571300483404 Elektor July/August 2020 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571300483404-has-digital-downloads - Elektor Magazine EN July/August 2020 (PDF) https://www.elektor.com/cdn/shop/files/elektor-07-08-2020-pdf_en.png?v=1705320147https://www.elektor.com/products/elektor-july-august-2020-pdf-en?variant=47571300483404 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47571303989580 Elektor July/August 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0508 Elektor Magazine EN July/August 2021 https://www.elektor.com/cdn/shop/files/elektor-07-08-2021_en.png?v=1705320157https://www.elektor.com/products/elektor-july-august-2021-en?variant=47571303989580 in stock 10.95 88 4.9 6.9 2 - 4 Werktage 47571307102540 Elektor July/August 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571307102540-has-digital-downloads - Elektor Magazine EN July/August 2021 (PDF) https://www.elektor.com/cdn/shop/files/elektor-07-08-2021-pdf_en.png?v=1705320167https://www.elektor.com/products/elektor-july-august-2021-pdf-en?variant=47571307102540 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666412585292 Elektor July/August 2022 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0514 Measuring Does Not Have to be Expensive Low-Cost Audio TesterUsing PC-Based Software and a USB Audio Interface AC Grid Frequency MeterMonitor Mains Frequency and Voltage A Modest Inductance MeterAn Affordable Solution for Your Workbench Acoustic Wave HoveringA Look at the Makerfabs Acoustic Levitation Kit Starting Out in ElectronicsRectifiers E-FFWD: Looking Ahead Again! Get Started With Your OscilloscopeFind Your Way Through the Knobs and Buttons Raspberry Pi Pico Makes an MSF-SDRDecode a Time Signal with a Pi Pico SDR Moisture Sensors for Watering SystemsAutomatic Watering Disruption in Test and Measurement EquipmentInnovation from the Smaller Players Infographics 7-8/2022 Inspiration, That’s What It’s All AboutInterview with Entrepreneur Walter Arkesteijn, InnoFaith Beauty Sciences Minimizing EMC Interference from Storage Chokes GUIs with Python (Part 5)Tic-Tac-Toe Reed RelaysPeculiar Parts, the series Simple Analog ESR Meter With Moving-Coil Meter Precision Sigfox CO2 Traffic LightNo Wi-Fi Network Needed! Women in Tech“It's All About Merit Until Merit Has Tits” Low-Budget Tablet Oscilloscope ADS1013DGood Value for Money? Smart Plug TeardownWhich Ones Are Hacker-Friendly? Skin Impedance and Skin CapacitanceSmall Experiments From Life’s ExperienceNo Local Business Pokit Meter ReviewA Swiss army knife of test gear HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-07-08-2022_en.png?v=1707314416https://www.elektor.com/products/elektor-july-august-2022-en?variant=47666412585292 in stock 10.95 99 4.9 6.9 2 - 4 Werktage 47666413306188 Elektor July/August 2022 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666413306188-has-digital-downloads - Measuring Does Not Have to be Expensive Low-Cost Audio TesterUsing PC-Based Software and a USB Audio Interface AC Grid Frequency MeterMonitor Mains Frequency and Voltage A Modest Inductance MeterAn Affordable Solution for Your Workbench Acoustic Wave HoveringA Look at the Makerfabs Acoustic Levitation Kit Starting Out in ElectronicsRectifiers E-FFWD: Looking Ahead Again! Get Started With Your OscilloscopeFind Your Way Through the Knobs and Buttons Raspberry Pi Pico Makes an MSF-SDRDecode a Time Signal with a Pi Pico SDR Moisture Sensors for Watering SystemsAutomatic Watering Disruption in Test and Measurement EquipmentInnovation from the Smaller Players Infographics 7-8/2022 Inspiration, That’s What It’s All AboutInterview with Entrepreneur Walter Arkesteijn, InnoFaith Beauty Sciences Minimizing EMC Interference from Storage Chokes GUIs with Python (Part 5)Tic-Tac-Toe Reed RelaysPeculiar Parts, the series Simple Analog ESR Meter With Moving-Coil Meter Precision Sigfox CO2 Traffic LightNo Wi-Fi Network Needed! Women in Tech“It's All About Merit Until Merit Has Tits” Low-Budget Tablet Oscilloscope ADS1013DGood Value for Money? Smart Plug TeardownWhich Ones Are Hacker-Friendly? Skin Impedance and Skin CapacitanceSmall Experiments From Life’s ExperienceNo Local Business Pokit Meter ReviewA Swiss army knife of test gear HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-07-08-2022-pdf_en.png?v=1707314428https://www.elektor.com/products/elektor-july-august-2022-pdf-en?variant=47666413306188 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666414190924 Elektor July/August 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0522 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Rotary Dial Phone as Remote ControlTo Switch On the Lights, Dial 1; For the Coffee Maker, Dial 2GPS-Based Speed MonitorNo More Speeding TicketsRGB Stroboscope with ArduinoA Colorful Adaptation of a Useful InstrumentWireless Emergency Push ButtonEnhanced Safety with LoRaStarting Out in ElectronicsFollow the EmitterArbitrary, Independent Hysteresis Levels for Comparatorswith Simulations, Spreadsheets and AlgebraESP32-Based Impedance AnalyzerSimple, Low-Part-Count, and Inexpensive!HomeLab ToursEncouraging DIYThe MCCAB Arduino Nano Training BoardAll-in-One Hardware for the “Microcontrollers Hands-On Course”From Life’s ExperienceModern LuddismSensor 101: The DS18B20 Temperature SensorConnection to the 1-Wire BusIs Matter the Thread to Save the Smart Home?New Standards to Simplify the Smart HomeA Matter of CollaborationDeveloping with the Thing Plus Matter Board and Simplicity StudioInfographics: IoT and SensorsMatter, ExpressLink, Rainmaker — What Is This All About?Q&A with Amey Inamdar, Technical Marketing Director at EspressifSelecting Microcontroller Dev Kits for IoT and IIoT ApplicationsAn Introductory GuideCapacitors Do Not Always Behave Capacitively!An NTP Clock with CircuitPythonWhy Should You Use This Programming Language?Build a Cool IoT DisplayWith the Phambili NewtThe HB100 Doppler Motion SensorTheory and PracticeA Bare-Metal Programming Guide (Part 1)For STM32 and Other ControllersSiglent SDM3045X MultimeterMicroprocessors for Embedded SystemsPeculiar Parts, the SeriesMicrocontroller Documentation Explained (Part 3)Block Diagrams and MoreLow-Power LoRa Weather StationBuild a long-range weather station by yourselfTransverter for the 70 cm BandClimate Calling EngineersMove Fast and Fix ThingsHexadoku https://www.elektor.com/cdn/shop/files/elektor-07-08-2023_en.png?v=1707314440https://www.elektor.com/products/elektor-july-august-2023-en?variant=47666414190924 in stock 10.95 18 4.9 6.9 2 - 4 Werktage 47666415665484 Elektor July/August 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666415665484-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Rotary Dial Phone as Remote ControlTo Switch On the Lights, Dial 1; For the Coffee Maker, Dial 2GPS-Based Speed MonitorNo More Speeding TicketsRGB Stroboscope with ArduinoA Colorful Adaptation of a Useful InstrumentWireless Emergency Push ButtonEnhanced Safety with LoRaStarting Out in ElectronicsFollow the EmitterArbitrary, Independent Hysteresis Levels for Comparatorswith Simulations, Spreadsheets and AlgebraESP32-Based Impedance AnalyzerSimple, Low-Part-Count, and Inexpensive!HomeLab ToursEncouraging DIYThe MCCAB Arduino Nano Training BoardAll-in-One Hardware for the “Microcontrollers Hands-On Course”From Life’s ExperienceModern LuddismSensor 101: The DS18B20 Temperature SensorConnection to the 1-Wire BusIs Matter the Thread to Save the Smart Home?New Standards to Simplify the Smart HomeA Matter of CollaborationDeveloping with the Thing Plus Matter Board and Simplicity StudioInfographics: IoT and SensorsMatter, ExpressLink, Rainmaker — What Is This All About?Q&A with Amey Inamdar, Technical Marketing Director at EspressifSelecting Microcontroller Dev Kits for IoT and IIoT ApplicationsAn Introductory GuideCapacitors Do Not Always Behave Capacitively!An NTP Clock with CircuitPythonWhy Should You Use This Programming Language?Build a Cool IoT DisplayWith the Phambili NewtThe HB100 Doppler Motion SensorTheory and PracticeA Bare-Metal Programming Guide (Part 1)For STM32 and Other ControllersSiglent SDM3045X MultimeterMicroprocessors for Embedded SystemsPeculiar Parts, the SeriesMicrocontroller Documentation Explained (Part 3)Block Diagrams and MoreLow-Power LoRa Weather StationBuild a long-range weather station by yourselfTransverter for the 70 cm BandClimate Calling EngineersMove Fast and Fix ThingsHexadoku https://www.elektor.com/cdn/shop/files/elektor-07-08-2023-pdf_en.png?v=1707314454https://www.elektor.com/products/elektor-july-august-2023-pdf-en?variant=47666415665484 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 46907274756428 Elektor Maart/April 2022 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0670 Bouw uw eigen RISC-V-controllerEerste stappen met de NEORV32 RISC-V softcore voor goedkope FPGA’s Het gebruik van Arduino’s seriële plotterGrafieken plotten met Arduino is gemakkelijk CLUE van AdafruitEen slimme oplossing voor IoT-projecten Bufferboard voor de Raspberry Pi 400Bescherm uw I/O’s Raspberry Pi RP2040-boards in overvloed Een handboek voor DHZ elektronische beveiliging en spionageSRAM – gebakken of diepgevroren Onderdelen identificerenTips & trucs, vakkunstigheden en andere nuttige informatie DHZ aanraakloze lichtschakelaar Alle begin......gaat compenseren en transformeren Nieuwe embedded-ontwikkelingenRust en het up-to-date houden van IoT-implementaties Infographics Hoe de industrie- en automobielsector zullen profiteren van 5G Relais met bewegende spoelVreemde onderdelen Oost West Lab BestAlles draait om de bank... Kennismaking met neuronen in neurale netwerkenDeel 4: embedded neuronen Magnetische levitatie “the very easy way”De derde en meest compacte versie PLC-programmering met de Raspberry Pi en het OpenPLC-projectVisualisatie van PLC-programma’s met AdvancedHMI Uit het leven gegrepenInpakken en wegwezen Onder de radarMicrocontrollers die u zou moeten kennen Draadloos monitoren en debuggenvoor Arduino, ESP32 en co. Draagbare temperatuur- en vochtigheidsmetermet gebruiksklare modules Lithium-accupacks reparerenSpaart geld + geeft meer kracht! GUI's maken met PythonMeme-Generator De drie grote vraagtekensWaarom wat wie Hexadoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2022_nl.png?v=1689092871https://www.elektor.com/products/elektor-maart-april-2022-nl?variant=46907274756428 in stock 14.95 72 4.9 6.9 2 - 4 Werktage 46907267187020 Elektor Maart/April 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907267187020-has-digital-downloads Bouw uw eigen RISC-V-controllerEerste stappen met de NEORV32 RISC-V softcore voor goedkope FPGA’s Het gebruik van Arduino’s seriële plotterGrafieken plotten met Arduino is gemakkelijk CLUE van AdafruitEen slimme oplossing voor IoT-projecten Bufferboard voor de Raspberry Pi 400Bescherm uw I/O’s Raspberry Pi RP2040-boards in overvloed Een handboek voor DHZ elektronische beveiliging en spionageSRAM – gebakken of diepgevroren Onderdelen identificerenTips & trucs, vakkunstigheden en andere nuttige informatie DHZ aanraakloze lichtschakelaar Alle begin......gaat compenseren en transformeren Nieuwe embedded-ontwikkelingenRust en het up-to-date houden van IoT-implementaties Infographics Hoe de industrie- en automobielsector zullen profiteren van 5G Relais met bewegende spoelVreemde onderdelen Oost West Lab BestAlles draait om de bank... Kennismaking met neuronen in neurale netwerkenDeel 4: embedded neuronen Magnetische levitatie “the very easy way”De derde en meest compacte versie PLC-programmering met de Raspberry Pi en het OpenPLC-projectVisualisatie van PLC-programma’s met AdvancedHMI Uit het leven gegrepenInpakken en wegwezen Onder de radarMicrocontrollers die u zou moeten kennen Draadloos monitoren en debuggenvoor Arduino, ESP32 en co. Draagbare temperatuur- en vochtigheidsmetermet gebruiksklare modules Lithium-accupacks reparerenSpaart geld + geeft meer kracht! GUI's maken met PythonMeme-Generator De drie grote vraagtekensWaarom wat wie Hexadoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2022-pdf_nl.png?v=1689092666https://www.elektor.com/products/elektor-maart-april-2022-pdf-nl?variant=46907267187020 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 46907268137292 Elektor Maart/April 2023 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907268137292-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Cloc 2.0de wekker die je altijd al wilde hebbenPIO in de praktijkexperimenten met de programmeerbare I/O van de RP2040Armeluis chiptweakerwe krijgen je wel (goedkoop) aan de praat...Echte USB-toevalsgeneratortwee PIC’s voor de prijs van één AVRPimp my mike...opvoeren doe je zelfFFT met Maixduinofrequentiespectra vastleggenUit het leven gegrepenontwerp(on)logicaUCN5804 stappenmotordrivervreemde onderdelenSimuleren met Micro-Capeerste stappen in een complexe wereldPAUL Award 2022jonge technische talenten en hun creatieve ontwerpenMijn eerste Software Defined Radioin minder dan 15 minuten klaarMicrocontroller-documentatie verklaarddeel 1: de opzet van een datasheetHoe verder met AI en embedded systems?tools, platforms – en worden schrijvers obsoleet?Digitalisering van verticale landbouwElektor Infographicsembedded en AI vandaag – en morgenEen introductie tot TinyMLCasestudy KwickPOSHigh-performance in elke klassecomputer-on-module standaardenAlle begin......wordt eindelijk actief!I²C-communicatie met Node.js en een Raspberry Pibekijk sensordata in een browserVideo-output met microcontrollers (2)VGA en DVIHet Metronom real-time besturingssysteemeen RTOS voor AVR-processorenDVI op de RP2040vraaggesprek met Luke Wren, chipontwikkelaar bij Raspberry PiDisplay-HAT Minitoont het weer op de Raspberry PiDe WEEF 2022 Awardshet goede vierenHexadoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2023-pdf_nl.png?v=1689092715https://www.elektor.com/products/elektor-maart-april-2023-pdf-nl?variant=46907268137292 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 46907274166604 Elektor Magazine NL November/December 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0668 BEELDVERWERKING MET DE NVIDIA JETSON NANO (DEEL 2)Beeldherkenning met Edge Impulse NIEUWS VAN ELEKTOR JUMPSTARTERNieuwe campagnes EEN OPEN SOURCE-PLATFORM VOOR GPS-TRACKINGMet Traccar voertuigen volgen zonder gebruik te maken van een cloudserver JOY-IT LCR-T7 MULTIFUNCTIONELE TESTERVoor passieve componenten, discrete halfgeleiders en IR RUISSYNTHESIZERVan ruis naar muziek met de PRBSynth1 ALLE BEGIN......speelt verder met de spoel KENNISMAKING MET NEURONEN IN NEURALE NETWERKEN (DEEL 2)Logische Neuronen BEVEILIGINGSPROBLEMEN? BESTRIJD VUUR MET VUUR!Met flitslampje beveiligde analoge geheugenuitbreiding voor de verzendbox met manipulatie-indicatie LCR METER POSTER BLUETOOTH-BAKENS IN DE PRAKTIJKindoor-plaatsbepaling PROGRAMMEREN IN C OP DE RASPBERRY PICommunicatie via WiFi (een hoofdstuk als voorbeeld) EMC PRE-COMPLIANCE TEST VOOR UW DC-GEVOED PROJECT (DEEL 2)De hardware en het gebruik ervan KENNISMAKING MET DE PARALLAX PROPELLER 2 (DEEL 5)Smart Pin-Functie MODBUS VIA WLAN (DEEL 1)Hardware en programmering OOST WEST LAB BEST... waar de Junior Computer weer tot leven is gewekt BOUW ZELF EEN NAUWKEURIGE KALIBRATOR-10 V tot +10 V, 0 tot 40 mA, 0,001% REVIEW: ARDUINO NANO RP2040 CONNECTRaspberry Pi RP2040 + WiFi + Bluetooth DE FYSIEKE KANT VAN KUNSTMATIGE INTELLIGENTIE PROJECT 2.0Correcties, Updates en Brieven van lezers MAAK GUI'S MET PYTHONIntroductie in guizero CO2-METER-BOUWKIT VOOR IN DE KLASEen ESP8266-project van de University of Applied Sciences Aachen NOSTALGISCHE MK484 MW/LW-RADIO...Altijd leuk om te bouwen! ELEKTOR @ 60Laat er licht zijn! HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2021_nl.png?v=1689092856https://www.elektor.com/products/elektor-magazine-nl-november-december-2021?variant=46907274166604 in stock 14.95 72 4.9 6.9 2 - 4 Werktage 46907266662732 Elektor Magazine NL November/December 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907266662732-has-digital-downloads BEELDVERWERKING MET DE NVIDIA JETSON NANO (DEEL 2)Beeldherkenning met Edge Impulse NIEUWS VAN ELEKTOR JUMPSTARTERNieuwe campagnes EEN OPEN SOURCE-PLATFORM VOOR GPS-TRACKINGMet Traccar voertuigen volgen zonder gebruik te maken van een cloudserver JOY-IT LCR-T7 MULTIFUNCTIONELE TESTERVoor passieve componenten, discrete halfgeleiders en IR RUISSYNTHESIZERVan ruis naar muziek met de PRBSynth1 ALLE BEGIN......speelt verder met de spoel KENNISMAKING MET NEURONEN IN NEURALE NETWERKEN (DEEL 2)Logische Neuronen BEVEILIGINGSPROBLEMEN? BESTRIJD VUUR MET VUUR!Met flitslampje beveiligde analoge geheugenuitbreiding voor de verzendbox met manipulatie-indicatie LCR METER POSTER BLUETOOTH-BAKENS IN DE PRAKTIJKindoor-plaatsbepaling PROGRAMMEREN IN C OP DE RASPBERRY PICommunicatie via WiFi (een hoofdstuk als voorbeeld) EMC PRE-COMPLIANCE TEST VOOR UW DC-GEVOED PROJECT (DEEL 2)De hardware en het gebruik ervan KENNISMAKING MET DE PARALLAX PROPELLER 2 (DEEL 5)Smart Pin-Functie MODBUS VIA WLAN (DEEL 1)Hardware en programmering OOST WEST LAB BEST... waar de Junior Computer weer tot leven is gewekt BOUW ZELF EEN NAUWKEURIGE KALIBRATOR-10 V tot +10 V, 0 tot 40 mA, 0,001% REVIEW: ARDUINO NANO RP2040 CONNECTRaspberry Pi RP2040 + WiFi + Bluetooth DE FYSIEKE KANT VAN KUNSTMATIGE INTELLIGENTIE PROJECT 2.0Correcties, Updates en Brieven van lezers MAAK GUI'S MET PYTHONIntroductie in guizero CO2-METER-BOUWKIT VOOR IN DE KLASEen ESP8266-project van de University of Applied Sciences Aachen NOSTALGISCHE MK484 MW/LW-RADIO...Altijd leuk om te bouwen! ELEKTOR @ 60Laat er licht zijn! HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2021-pdf_nl.png?v=1689092652https://www.elektor.com/products/elektor-magazine-nl-november-december-2021-pdf?variant=46907266662732 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 46907272003916 Elektor Magazine NL September/Oktober 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0667 KENNISMAKING MET NEURONEN IN NEURALE NETWERKEN (DEEL 1)Kunstmatige Neuronen EMC PRE-COMPLIANCE TEST VOOR UW DC-GEVOED PROJECT (DEEL 1)Dubbele DC-LISN ELEKTRONISCHE BELASTING VOOR DC EN ACTot 400 V en 10 A (piek) ALLE BEGIN......neemt het op tegen de spoel! BEELDVERWERKING MET DE NVIDIA JETSON NANO (DEEL 1)De Hardware en Software EEN GEDETAILLEERD ONDERZOEK NAAR NETTRANSFORMATORENIn- en uitschakelgedrag YES WE CAN MET PICAN 3Een CAN Bus HAT voor de Raspberry Pi 4 ZONNEPANELEN OP JE BALKONZelfbouw balkoncentrale = snel terugverdiend! BEELDVERWERKING EN VIDEO-STREAMING MET EEN RASPBERRY PI 4De Raspberry Pi High-Quality Camera in de praktijk DISPLAYS GEBRUIKEN IN RASPBERRY PI-PROJECTENEen hoofdstuk als voorbeeld: Organische LED-displays (OLED) KENNISMAKING MET DE PARALLAX PROPELLER 2 (DEEL 4):Tekens Versturen ELEKTOR @ 60Een terugblik op voorgaande septembers OOST WEST LAB BESTop het Friese platteland, waar de buizen bloeien... HYBRIDENVreemde onderdelen, de serie EEN KOMPASROOS MET DE GY-271Of waarom we in een acht bewegen om een sensor te kalibreren HOE GROOT IS UW VOETAFDRUK?Bereken de ecologische voetafdruk van uw elektronica CONNECTED THERMOSTAAT MET ESP32Houd uw wijn op de juiste temperatuur! MAGNETISCHE LEVITATIE OP DE DIGITALE MANIERESP32 Pico vervangt de Analoge Comparator ULTIMATE ARDUINO UNO HARDWARE MANUALEen hoofdstuk als voorbeeld: Main Microcontroller Bootloader MICROPYTHON VOOR DE ESP32 C.S. (DEEL 2)Eenvoudig Matrix Displays besturen MADMACHINE SWIFTIO BOARDModerne taal ontmoet moderne Hardware UIT HET LEVEN GEGREPENKnipperlichtrelatie HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2021_nl.png?v=1689092848https://www.elektor.com/products/elektor-magazine-nl-september-oktober-2021?variant=46907272003916 in stock 14.95 24 4.9 6.9 2 - 4 Werktage 46907266629964 Elektor Magazine NL September/Oktober 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907266629964-has-digital-downloads KENNISMAKING MET NEURONEN IN NEURALE NETWERKEN (DEEL 1)Kunstmatige Neuronen EMC PRE-COMPLIANCE TEST VOOR UW DC-GEVOED PROJECT (DEEL 1)Dubbele DC-LISN ELEKTRONISCHE BELASTING VOOR DC EN ACTot 400 V en 10 A (piek) ALLE BEGIN......neemt het op tegen de spoel! BEELDVERWERKING MET DE NVIDIA JETSON NANO (DEEL 1)De Hardware en Software EEN GEDETAILLEERD ONDERZOEK NAAR NETTRANSFORMATORENIn- en uitschakelgedrag YES WE CAN MET PICAN 3Een CAN Bus HAT voor de Raspberry Pi 4 ZONNEPANELEN OP JE BALKONZelfbouw balkoncentrale = snel terugverdiend! BEELDVERWERKING EN VIDEO-STREAMING MET EEN RASPBERRY PI 4De Raspberry Pi High-Quality Camera in de praktijk DISPLAYS GEBRUIKEN IN RASPBERRY PI-PROJECTENEen hoofdstuk als voorbeeld: Organische LED-displays (OLED) KENNISMAKING MET DE PARALLAX PROPELLER 2 (DEEL 4):Tekens Versturen ELEKTOR @ 60Een terugblik op voorgaande septembers OOST WEST LAB BESTop het Friese platteland, waar de buizen bloeien... HYBRIDENVreemde onderdelen, de serie EEN KOMPASROOS MET DE GY-271Of waarom we in een acht bewegen om een sensor te kalibreren HOE GROOT IS UW VOETAFDRUK?Bereken de ecologische voetafdruk van uw elektronica CONNECTED THERMOSTAAT MET ESP32Houd uw wijn op de juiste temperatuur! MAGNETISCHE LEVITATIE OP DE DIGITALE MANIERESP32 Pico vervangt de Analoge Comparator ULTIMATE ARDUINO UNO HARDWARE MANUALEen hoofdstuk als voorbeeld: Main Microcontroller Bootloader MICROPYTHON VOOR DE ESP32 C.S. (DEEL 2)Eenvoudig Matrix Displays besturen MADMACHINE SWIFTIO BOARDModerne taal ontmoet moderne Hardware UIT HET LEVEN GEGREPENKnipperlichtrelatie HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2021-pdf_nl.png?v=1689092645https://www.elektor.com/products/elektor-magazine-nl-september-oktober-2021-pdf?variant=46907266629964 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47571331219788 Elektor March/April 2020 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571331219788-has-digital-downloads - Elektor Magazine EN March/April 2020 (PDF) https://www.elektor.com/cdn/shop/files/elektor-03-04-2020-pdf_en.png?v=1705320420https://www.elektor.com/products/elektor-march-april-2020-pdf-en?variant=47571331219788 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47571332071756 Elektor March/April 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0506 The Vision and Engineering Behind SparkFun Getting Started with MicroMod Leveling Up Your SparkFun JetBotHow I Expanded the Functionality of My JetBot, Powered by the NVIDIA Jetson Nano Programming an FPGA How to Build a DIY GNSS Reference Station The ClockClock Project Under the Hood: SparkFun Inventor's Kit SparkFun’s Glenn Samala on Product Development and New Ventures Creating Custom Circuit Boards with SparkFun À La Carte Designing with the SparkFun Artemis Getting Started with the Qwiic Ecosystem for Rapid Prototyping Poster - Qwiic Under the Hood: The GreatScott! / Elektor DIY LiPo Supercharger Kit Memorable Electronics from SparkFun Past Perfect Parking with LiDAR Buried Pad PCB Fixing Design to Sale: the SparkFun RTK Surveyor Hello World from the Raspberry Pi Pico and RP2040A Look at Raspberry Pi’s First Microcontroller and Microcontroller Chip DIY Quadrupedal Robots Poster - Micromod RISC-V IoT Development in AWS Using FreeRTOS Libraries Yep, Electronics = Fun!A Conversation Among Electronics Enthusiasts Sparkfun Product Catalog HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2021_en.png?v=1705320432https://www.elektor.com/products/elektor-march-april-2021-en?variant=47571332071756 in stock 10.95 8 4.9 6.9 2 - 4 Werktage 47666416615756 Elektor March/April 2022 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0512 Build Your Own RISC-V ControllerFirst Steps with the NEORV32 RISC-V Softcore for Low-Cost FPGAs How to Use Arduino’s Serial PlotterPlotting Graphs With Arduino Is Easy CLUE from AdafruitA Smart Solution for IoT Projects Buffer Board for the Raspberry Pi 400Protect the I/Os Raspberry Pi RP2040 Boards Aplenty A Handbook on DIY Electronic Security and EspionageSRAM Heated or Deep-Frozen Component IdentificationTips & Tricks, Best Practices and Other Useful Information DIY Touchless Light Switch Starting out in ElectronicsMatching and Transforming What’s New in Embedded Development?Rust and Keeping IoT Deployments Updated Infographics How the Industrial and Automotive Sectors Will Benefit from 5G Moving Coil RelaysPeculiar Parts, the series HomeLab ToursEverything Revolves Around the Tools... Understanding the Neurons in Neural Networks (Part 4)Embedded Neurons Magnetic Levitation the Very Easy WayThe Third and Most Compact Version PLC Programming with the Raspberry Pi and the OpenPLC ProjectVisualization of PLC Programs with AdvancedHMI From Life's ExperiencePack Up and Leave Under Your RadarMicrocontrollers You Should Know About Monitor and Debug Over the AirA Solution for Arduino, ESP32 and Co. Portable Temperature- and Humidity-Measuring DeviceUsing Ready-Made Modules Lithium Battery Pack RepairSave Money + More Power! GUIs with PythonMeme-Generator Three Questions to Build OnWhy, What, and Who? HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2022_en.png?v=1707314489https://www.elektor.com/products/elektor-march-april-2022-en?variant=47666416615756 in stock 10.95 73 4.9 6.9 2 - 4 Werktage 47666418352460 Elektor March/April 2022 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666418352460-has-digital-downloads - Build Your Own RISC-V ControllerFirst Steps with the NEORV32 RISC-V Softcore for Low-Cost FPGAs How to Use Arduino’s Serial PlotterPlotting Graphs With Arduino Is Easy CLUE from AdafruitA Smart Solution for IoT Projects Buffer Board for the Raspberry Pi 400Protect the I/Os Raspberry Pi RP2040 Boards Aplenty A Handbook on DIY Electronic Security and EspionageSRAM Heated or Deep-Frozen Component IdentificationTips & Tricks, Best Practices and Other Useful Information DIY Touchless Light Switch Starting out in ElectronicsMatching and Transforming What’s New in Embedded Development?Rust and Keeping IoT Deployments Updated Infographics How the Industrial and Automotive Sectors Will Benefit from 5G Moving Coil RelaysPeculiar Parts, the series HomeLab ToursEverything Revolves Around the Tools... Understanding the Neurons in Neural Networks (Part 4)Embedded Neurons Magnetic Levitation the Very Easy WayThe Third and Most Compact Version PLC Programming with the Raspberry Pi and the OpenPLC ProjectVisualization of PLC Programs with AdvancedHMI From Life's ExperiencePack Up and Leave Under Your RadarMicrocontrollers You Should Know About Monitor and Debug Over the AirA Solution for Arduino, ESP32 and Co. Portable Temperature- and Humidity-Measuring DeviceUsing Ready-Made Modules Lithium Battery Pack RepairSave Money + More Power! GUIs with PythonMeme-Generator Three Questions to Build OnWhy, What, and Who? HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2022-pdf_en.png?v=1707314507https://www.elektor.com/products/elektor-march-april-2022-pdf-en?variant=47666418352460 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666419007820 Elektor March/April 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0520 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Cloc 2.0The Alarm Clock You've Always WantedRP2040 PIO in PracticeExperiments Using the RP2040’s Programmable I/OPoor Man's ChipTweakerWe Have (Low-Budget) Ways of Making You TalkUSB True Random Number GeneratorTwo PICs for the Price of One AVRPimp My MicSelf-Designed Level BoosterFFT with a MaixduinoFrequency spectrum displayFrom Life’s ExperienceDesign Logic (or Non-Logic)UCN5804 Stepper Motor DriverPeculiar Parts, the SeriesCircuit Simulation With Micro-CapFirst Steps in a Complicated WorldPAUL Award 2022Young Technical Talents and Their Creative SolutionsMy First Software-Defined RadioBuilt in Less Than 15 MinutesMicrocontroller Documentation Explained (Part 1)Datasheet structureWhat’s Next for AI and Embedded Systems?Tools, Platforms, and Writer ReplacementsDigitizing Vertical FarmingInfographics: Embedded and AI Today and TomorrowAn Introduction to TinyMLJetCarrier96A Versatile NVIDIA Jetson Development SystemCase Study: Taking EV Charging Global with a Universal RFID SolutionHigh-Performance in Every ClassComputer-on-Module StandardsStarting Out in ElectronicsLet’s Get Active!I²C Communication Using Node.js and a Raspberry PiSee Your Sensor Data in a BrowserVideo Output with Microcontrollers (2)VGA and DVI OutputThe Metronom Real-Time Operating SystemAn RTOS for AVR ProcessorsDVI on the RP2040An Interview with Luke Wren, Chip Developer at Raspberry PiDisplay HAT MiniShow the Weather Forecast on Raspberry Pi!WEEF 2022 Awards: Celebrate the GoodHexadoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2023_en.png?v=1707314520https://www.elektor.com/products/elektor-march-april-2023-en?variant=47666419007820 in stock 10.95 110 4.9 6.9 2 - 4 Werktage 47666419499340 Elektor March/April 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666419499340-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Cloc 2.0The Alarm Clock You've Always WantedRP2040 PIO in PracticeExperiments Using the RP2040’s Programmable I/OPoor Man's ChipTweakerWe Have (Low-Budget) Ways of Making You TalkUSB True Random Number GeneratorTwo PICs for the Price of One AVRPimp My MicSelf-Designed Level BoosterFFT with a MaixduinoFrequency spectrum displayFrom Life’s ExperienceDesign Logic (or Non-Logic)UCN5804 Stepper Motor DriverPeculiar Parts, the SeriesCircuit Simulation With Micro-CapFirst Steps in a Complicated WorldPAUL Award 2022Young Technical Talents and Their Creative SolutionsMy First Software-Defined RadioBuilt in Less Than 15 MinutesMicrocontroller Documentation Explained (Part 1)Datasheet structureWhat’s Next for AI and Embedded Systems?Tools, Platforms, and Writer ReplacementsDigitizing Vertical FarmingInfographics: Embedded and AI Today and TomorrowAn Introduction to TinyMLJetCarrier96A Versatile NVIDIA Jetson Development SystemCase Study: Taking EV Charging Global with a Universal RFID SolutionHigh-Performance in Every ClassComputer-on-Module StandardsStarting Out in ElectronicsLet’s Get Active!I²C Communication Using Node.js and a Raspberry PiSee Your Sensor Data in a BrowserVideo Output with Microcontrollers (2)VGA and DVI OutputThe Metronom Real-Time Operating SystemAn RTOS for AVR ProcessorsDVI on the RP2040An Interview with Luke Wren, Chip Developer at Raspberry PiDisplay HAT MiniShow the Weather Forecast on Raspberry Pi!WEEF 2022 Awards: Celebrate the GoodHexadoku https://www.elektor.com/cdn/shop/files/elektor-03-04-2023-pdf_en.png?v=1707314532https://www.elektor.com/products/elektor-march-april-2023-pdf-en?variant=47666419499340 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47757752631628 Elektor March/April 2024 (EN) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Magazines > NEW EP-0528 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.CaptureCountAn Object Detector and Counter on the Raspberry Pi 5Voltage Reference With Arduino Pro MiniLinearize and Calibrate Your Analog InputsFPGAs for BeginnersThe Path From MCU to FPGA ProgrammingUpdate: STM32 Wireless Innovation Design Contest 2024Bluetooth LE With MAUIControl Apps for Android & Co.Port-Expanding Breakout BoardIncrease the Number of I/Os on Your Dev BoardAI SpecialistMachine Learning with the Jetson Nano2024: An AI OdysseyFirst Forays Into TensorFlow262,144 Ways to Play The Game of LifeA Reader’s Project in BriefFrom Life’s ExperienceThe Chinese DragonGet Your (Brushed DC) Motor Running!Sample Projects from the Elektor Motor Control Development BundleESP32-RS-232 AdapterA Wireless Link for Classic Test EquipmentStarting Out in Electronics……More About OpampsESP Library RecommendationsPiezoelectric DevicesPeculiar Parts, the SeriesA Smart Object CounterImage Recognition Made Easy with Edge ImpulseResolve Your Trickiest Embedded Development ChallengesESP32 TerminalA Handheld Device with a Touch-Capable DisplayGetting Started With the Zephyr RTOSAs Powerful as It Is Hard to MasterAward-Winning EthicsA Dialog with CTO Alexander Gerfer of Würth Elektronik eiSos on Enabling Innovation and Mindful BehaviorErr-lectronicsCorrections, Updates, and Readers’ LettersInfographics: Embedded and AISquare Wave Generation BenchmarksExploring ESP32, Pico, and Other Microcontrollers https://www.elektor.com/cdn/shop/files/elektor-3-4-2024_en.png?v=1709219029https://www.elektor.com/products/elektor-march-april-2024-en?variant=47757752631628 in stock 10.95 134 4.9 6.9 2 - 4 Werktage 47757764395340 Elektor March/April 2024 PDF (EN) Elektor Digital bundels Bestsellers > Elektor (Digital) > Magazines has-digital-downloads,variant-47757764395340-has-digital-downloads Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.CaptureCountAn Object Detector and Counter on the Raspberry Pi 5Voltage Reference With Arduino Pro MiniLinearize and Calibrate Your Analog InputsFPGAs for BeginnersThe Path From MCU to FPGA ProgrammingUpdate: STM32 Wireless Innovation Design Contest 2024Bluetooth LE With MAUIControl Apps for Android & Co.Port-Expanding Breakout BoardIncrease the Number of I/Os on Your Dev BoardAI SpecialistMachine Learning with the Jetson Nano2024: An AI OdysseyFirst Forays Into TensorFlow262,144 Ways to Play The Game of LifeA Reader’s Project in BriefFrom Life’s ExperienceThe Chinese DragonGet Your (Brushed DC) Motor Running!Sample Projects from the Elektor Motor Control Development BundleESP32-RS-232 AdapterA Wireless Link for Classic Test EquipmentStarting Out in Electronics……More About OpampsESP Library RecommendationsPiezoelectric DevicesPeculiar Parts, the SeriesA Smart Object CounterImage Recognition Made Easy with Edge ImpulseResolve Your Trickiest Embedded Development ChallengesESP32 TerminalA Handheld Device with a Touch-Capable DisplayGetting Started With the Zephyr RTOSAs Powerful as It Is Hard to MasterAward-Winning EthicsA Dialog with CTO Alexander Gerfer of Würth Elektronik eiSos on Enabling Innovation and Mindful BehaviorErr-lectronicsCorrections, Updates, and Readers’ LettersInfographics: Embedded and AISquare Wave Generation BenchmarksExploring ESP32, Pico, and Other Microcontrollers https://www.elektor.com/cdn/shop/files/elektor-3-4-2024-pdf_en.png?v=1709219064https://www.elektor.com/products/elektor-march-april-2024-pdf-en?variant=47757764395340 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47571340624204 Elektor May/June 2020 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571340624204-has-digital-downloads - Elektor Magazine EN May/June 2020 (PDF) https://www.elektor.com/cdn/shop/files/elektor-05-06-2020-pdf_en.png?v=1705320501https://www.elektor.com/products/elektor-may-june-2020-pdf-en?variant=47571340624204 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47571344818508 Elektor May/June 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0507 Elektor Magazine EN May/June 2021 https://www.elektor.com/cdn/shop/files/elektor-05-06-2021_en.png?v=1705320513https://www.elektor.com/products/elektor-may-june-2021-en?variant=47571344818508 in stock 10.95 58 4.9 6.9 2 - 4 Werktage 47571345899852 Elektor May/June 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571345899852-has-digital-downloads - Elektor Magazine EN May/June 2021 (PDF) https://www.elektor.com/cdn/shop/files/elektor-05-06-2021-pdf_en.png?v=1705320524https://www.elektor.com/products/elektor-may-june-2021-pdf-en?variant=47571345899852 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666420089164 Elektor May/June 2022 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0513 Your First Steps with an ESP32-C3 and the IoTA Wi-Fi Button and Relay IoT Cloud a la Arduino Dual Geiger-Müller Tube Arduino ShieldA High Sensitivity, Very Low-Power Radiation Sensor CO2 GuardA DIY Approach to Monitoring Air Quality MonkMakes Air Quality Kit for Raspberry PiMeasures Temperature and eCO2 Starting Out in ElectronicsWelcome to the Diode Tips & Tricks for Testing ComponentsNo Expensive Equipment Required Reducing the Power Consumption of Your Mole RepellerAn ATtiny13 Replaces a 555 Light Switch DeLuxA Solution for High-Precision Light-Controlled Switching The Challenges in Bringing IoT Solutions to MarketWorries Around Security, Scalability, and Competition Infographics 5-6/2022 Preferably Wired After AllTips for Developing a 1 Gbit/s Interface in an Industrial Environment Bringing Real-Time Object Detection to MCUs with Edge Impulse FOMO Traveling-Wave TubesPeculiar Parts, the Series Narrowband Internet of ThingsStandards, Coverage, Agreements, and Modules Dragino LPS8 Indoor GatewaySpeedy LoRaWAN Gateway Setup Explore ATtiny Microcontrollers Using C and Assembly LanguageSample Chapter: ATtiny I/O Ports Err-lectronicsCorrections, Updates and Readers’ Letters LoRa GPS Tracker UpdateReceive and Show Location Using a Raspberry Pi Circuit Simulation with TINA Design Suite & TINACloudSample Chapter: Sinusoidal Oscillators From Life’s ExperienceAssembly Line Work The WinUI Graphics Framework for Windows AppsA Small Demo Application GUIs with PythonWorst GUI of the world Off-Grid Solar SystemsElectrical Energy Independent of the Mains Grid The 10-Year SmartphoneRenew Your Expectations HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-05-06-2022_en.png?v=1707314544https://www.elektor.com/products/elektor-may-june-2022-en?variant=47666420089164 in stock 10.95 94 4.9 6.9 2 - 4 Werktage 47666420711756 Elektor May/June 2022 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666420711756-has-digital-downloads - Your First Steps with an ESP32-C3 and the IoTA Wi-Fi Button and Relay IoT Cloud a la Arduino Dual Geiger-Müller Tube Arduino ShieldA High Sensitivity, Very Low-Power Radiation Sensor CO2 GuardA DIY Approach to Monitoring Air Quality MonkMakes Air Quality Kit for Raspberry PiMeasures Temperature and eCO2 Starting Out in ElectronicsWelcome to the Diode Tips & Tricks for Testing ComponentsNo Expensive Equipment Required Reducing the Power Consumption of Your Mole RepellerAn ATtiny13 Replaces a 555 Light Switch DeLuxA Solution for High-Precision Light-Controlled Switching The Challenges in Bringing IoT Solutions to MarketWorries Around Security, Scalability, and Competition Infographics 5-6/2022 Preferably Wired After AllTips for Developing a 1 Gbit/s Interface in an Industrial Environment Bringing Real-Time Object Detection to MCUs with Edge Impulse FOMO Traveling-Wave TubesPeculiar Parts, the Series Narrowband Internet of ThingsStandards, Coverage, Agreements, and Modules Dragino LPS8 Indoor GatewaySpeedy LoRaWAN Gateway Setup Explore ATtiny Microcontrollers Using C and Assembly LanguageSample Chapter: ATtiny I/O Ports Err-lectronicsCorrections, Updates and Readers’ Letters LoRa GPS Tracker UpdateReceive and Show Location Using a Raspberry Pi Circuit Simulation with TINA Design Suite & TINACloudSample Chapter: Sinusoidal Oscillators From Life’s ExperienceAssembly Line Work The WinUI Graphics Framework for Windows AppsA Small Demo Application GUIs with PythonWorst GUI of the world Off-Grid Solar SystemsElectrical Energy Independent of the Mains Grid The 10-Year SmartphoneRenew Your Expectations HexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-05-06-2022-pdf_en.png?v=1707314555https://www.elektor.com/products/elektor-may-june-2022-pdf-en?variant=47666420711756 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666421399884 Elektor May/June 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0521 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Knowledge for All!Super Servo TesterTest Up to Four Servos Stand-Alone or In-SystemAnalog Signals and MicrocontrollersADCs, DACs, Current Measurement, and Moreembedded world 2023Sub-Nyquist Sampling in PracticeReliably Capturing Higher Frequencies Using SubsamplingAndroid Smartphone Here, ESP32 There?Practical Pproject Using the Android Wi-Fi APIActive 1-kHz Filter for Distortion MeasurementBetter Measurements Through Optimization of the Measurement SignalStarting Out in Electronics......Multivibrating Cheerfully Further!Err-lectronicsCorrections, Updates and Readers’ LettersThe New I3C ProtocolA Worthy Successor to I²C, or Just More Hot Air?BlueRC: IR Remote Control with Smartphone and ESP32Adaptive and UniversalMicrocontroller Documentation Explained (Part 2)Registers and Block DiagramsAutomating Test and MeasurementProgramming Test Equipment to Do What You WantInfographics: Test and MeasurementOvervoltage Protection for Safe OperationTransient Protection for Non-Isolated DC/DC Power ModulesWiha Measuring EquipmentReliable Electrical Testers and MetersAutomating Testing and Collaborating on Test ResultsFrom Life’s ExperienceHigh-Level ElectronicsEnergy LoggerMeasuring and Recording Power ConsumptionAssembling the 4tronix M.A.R.S. Rover KitParking Disk with E-Paper DisplayAn Innovative Digital ReplacementeCO₂ Telegram botAir-Quality Measurement with Telegram NotificationBehind the Scenes of DIY High-End AudioElektor’s Ton Giesberts Interviewed on the Fine Art of Analog DesignHomeLab ToursWork in Progress...RFID Tag Reading and RFID Door LockSample Projects from the Elektor Arduino Experimenting BundleOscilloscope Current Probe for RFRF Current Measurements Made EasyNot for the Faint-Hearted: Robot Arm KitWith Raspberry Pi Pico and MicroPythonGenerative AIWho Made This Anyway?Hexadoku https://www.elektor.com/cdn/shop/files/elektor-05-06-2023_en.png?v=1707314568https://www.elektor.com/products/elektor-may-june-2023-en?variant=47666421399884 in stock 10.95 110 4.9 6.9 2 - 4 Werktage 47666421891404 Elektor May/June 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666421891404-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Knowledge for All!Super Servo TesterTest Up to Four Servos Stand-Alone or In-SystemAnalog Signals and MicrocontrollersADCs, DACs, Current Measurement, and Moreembedded world 2023Sub-Nyquist Sampling in PracticeReliably Capturing Higher Frequencies Using SubsamplingAndroid Smartphone Here, ESP32 There?Practical Pproject Using the Android Wi-Fi APIActive 1-kHz Filter for Distortion MeasurementBetter Measurements Through Optimization of the Measurement SignalStarting Out in Electronics......Multivibrating Cheerfully Further!Err-lectronicsCorrections, Updates and Readers’ LettersThe New I3C ProtocolA Worthy Successor to I²C, or Just More Hot Air?BlueRC: IR Remote Control with Smartphone and ESP32Adaptive and UniversalMicrocontroller Documentation Explained (Part 2)Registers and Block DiagramsAutomating Test and MeasurementProgramming Test Equipment to Do What You WantInfographics: Test and MeasurementOvervoltage Protection for Safe OperationTransient Protection for Non-Isolated DC/DC Power ModulesWiha Measuring EquipmentReliable Electrical Testers and MetersAutomating Testing and Collaborating on Test ResultsFrom Life’s ExperienceHigh-Level ElectronicsEnergy LoggerMeasuring and Recording Power ConsumptionAssembling the 4tronix M.A.R.S. Rover KitParking Disk with E-Paper DisplayAn Innovative Digital ReplacementeCO₂ Telegram botAir-Quality Measurement with Telegram NotificationBehind the Scenes of DIY High-End AudioElektor’s Ton Giesberts Interviewed on the Fine Art of Analog DesignHomeLab ToursWork in Progress...RFID Tag Reading and RFID Door LockSample Projects from the Elektor Arduino Experimenting BundleOscilloscope Current Probe for RFRF Current Measurements Made EasyNot for the Faint-Hearted: Robot Arm KitWith Raspberry Pi Pico and MicroPythonGenerative AIWho Made This Anyway?Hexadoku https://www.elektor.com/cdn/shop/files/elektor-05-06-2023-pdf_en.png?v=1707314579https://www.elektor.com/products/elektor-may-june-2023-pdf-en?variant=47666421891404 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 46907275051340 Elektor Mei/Juni 2022 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0671 Eerste stappen met een ESP32-C3 en het IoTWiFi-knop en -relais IoT Cloud à la Arduino Arduino-shield met dubbele Geiger-Müller buisuiterst gevoelige en zeer zuinige stralingssensor CO2-wachterluchtkwaliteit bewaken – doe het zelf! MonkMakes Air Quality Kit voor de Raspberry Pimeet temperatuur en eCO2 Alle begin......verwelkomt de diode Tips & trucs voor het testen van componentenzonder kostbare apparatuur Reduceer het stroomverbruik van uw mollenverjagerATtiny13 in plaats van 555 Lichtschakelaar DeLuxuiterst nauwkeurig lichtgestuurd schakelen Uitdagingen bij het op de markt brengen van IoT-oplossingenzorgen over veiligheid, schaalbaarheid en de concurrentie Elektor Infographics Toch beter bedraadTips voor het ontwikkelen van een 1 Gbit/s interface in de industriële omgeving Edge Impulse FOMOreal-time objectdetectie voor MCU’s Lopende-golfbuisVreemde onderdelen, de serie Smalband-Internet of Thingsstandaarden, dekking, overeenkomsten en modules Dragino LPS8 indoor-gatewayLoRaWAN-gateway snel geïnstalleerd Ontdek ATtiny-microcontrollers met behulp van C en assemblervoorbeeldhoofdstuk: ATtiny I/O-poorten Project 2.0correcties, updates en brieven van lezers LoRa GPS-tracker updateontvang en toon de locatie met een Raspberry Pi Schakelingen simuleren met TINA Design Suite & TINACloudvoorbeeldhoofdstuk: sinusoscillatoren Uit het leven gegrepenlopendebandwerk Het WinUI grafische framework voor Windows-appseen kleine demo-applicatie GUI's maken met Python's Werelds slechtste GUI Off-grid PV-systeemelektrische energie onafhankelijk van het net De 10-jaar-smartphonestel uw verwachtingen bij Hexadoku https://www.elektor.com/cdn/shop/files/elektor-05-06-2022_nl.png?v=1689092878https://www.elektor.com/products/elektor-mei-juni-2022-nl?variant=46907275051340 in stock 14.95 87 4.9 6.9 2 - 4 Werktage 46907267318092 Elektor Mei/Juni 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907267318092-has-digital-downloads Eerste stappen met een ESP32-C3 en het IoTWiFi-knop en -relais IoT Cloud à la Arduino Arduino-shield met dubbele Geiger-Müller buisuiterst gevoelige en zeer zuinige stralingssensor CO2-wachterluchtkwaliteit bewaken – doe het zelf! MonkMakes Air Quality Kit voor de Raspberry Pimeet temperatuur en eCO2 Alle begin......verwelkomt de diode Tips & trucs voor het testen van componentenzonder kostbare apparatuur Reduceer het stroomverbruik van uw mollenverjagerATtiny13 in plaats van 555 Lichtschakelaar DeLuxuiterst nauwkeurig lichtgestuurd schakelen Uitdagingen bij het op de markt brengen van IoT-oplossingenzorgen over veiligheid, schaalbaarheid en de concurrentie Elektor Infographics Toch beter bedraadTips voor het ontwikkelen van een 1 Gbit/s interface in de industriële omgeving Edge Impulse FOMOreal-time objectdetectie voor MCU’s Lopende-golfbuisVreemde onderdelen, de serie Smalband-Internet of Thingsstandaarden, dekking, overeenkomsten en modules Dragino LPS8 indoor-gatewayLoRaWAN-gateway snel geïnstalleerd Ontdek ATtiny-microcontrollers met behulp van C en assemblervoorbeeldhoofdstuk: ATtiny I/O-poorten Project 2.0correcties, updates en brieven van lezers LoRa GPS-tracker updateontvang en toon de locatie met een Raspberry Pi Schakelingen simuleren met TINA Design Suite & TINACloudvoorbeeldhoofdstuk: sinusoscillatoren Uit het leven gegrepenlopendebandwerk Het WinUI grafische framework voor Windows-appseen kleine demo-applicatie GUI's maken met Python's Werelds slechtste GUI Off-grid PV-systeemelektrische energie onafhankelijk van het net De 10-jaar-smartphonestel uw verwachtingen bij Hexadoku https://www.elektor.com/cdn/shop/files/elektor-05-06-2022-pdf_nl.png?v=1689092673https://www.elektor.com/products/elektor-mei-juni-2022-pdf-nl?variant=46907267318092 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 46907268268364 Elektor Mei/Juni 2023 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907268268364-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Super-servotestervoor vier servo’s – stand-alone of in-systemAnaloge signalen en microcontrollersADC’s, DAC’s, stroommeting en meerembedded world 2023Sub-Nyquist-sampling in de praktijkhogere frequenties betrouwbaar bemonsteren met subsamplingMet Android-smartphone, spreek ik met ESP32?praktisch project met behulp van de Android WiFi-APIActief 1kHz-filter voor vervormingsmetingmeet beter door het het meetsignaal te optimaliserenAlle begin......multivibreert verder!Project 2.0correcties, updates en brieven van lezersHet nieuwe I3C-protocoleen waardig opvolger van I2C – of gebakken lucht?BlueRC: IR-afstandsbediening met smartphone en ESP32universeel en aanpasbaarMicrocontroller-documentatie verklaarddeel 2: registers en blokschema’sAutomatisering van testen en metentestapparatuur programmeren om je te dienenElektor Infographicstesten en metenOverspanningsbeveiliging voor veilige werkingtransiëntbescherming voor niet-geïsoleerde DC/DC-voedingsmodulesMeetapparatuur van het merk Wihatesters en meters voor installaties waar u op kunt bouwenAutomatisch testen en samenwerken aan testresultatenUit het leven gegrepenelektronica op hoog niveauEnergieloggermeet en registreert het stroomverbruikMontage van de M.A.R.S. Rover Kit van 4tronixParkeerschijf met e-papier displayinnovatief digitaal alternatiefeCO2 Telegram-botmeet de luchtkwaliteit via TelegramAchter de schermen van DHZ high-end audioTon Giesberts van Elektor over de fijne kneepjes van het analoog ontwerpenOost West Lab Bestwerk in uitvoering...RFID-tag’s lezen, en een RFID-deurslotvoorbeeldprojecten uit de Elektor Arduino ExperimenteerbundelHF-stroomprobe voor oscilloscoopHF-stroommetingen gemakkelijk gemaaktNiet voor watjes – Makerfabs Robot Arm Kitmet de Raspberry Pi Pico en MicroPythonGeneratieve KIwie heeft dit eigenlijk gemaakt?Hexadokupuzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-05-06-2023-pdf_nl.png?v=1689092723https://www.elektor.com/products/elektor-mei-juni-2023-pdf-nl?variant=46907268268364 in stock 9.95 -1 4.9 6.9 2 - 4 Werktage 47571346981196 Elektor November/December 2020 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571346981196-has-digital-downloads - Elektor Magazine EN November/December 2020 (PDF) https://www.elektor.com/cdn/shop/files/elektor-11-12-2020-pdf_en.png?v=1705320534https://www.elektor.com/products/elektor-november-december-2020-pdf-en?variant=47571346981196 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666422350156 Elektor November/December 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0510 IMAGE PROCESSING WITH THE NVIDIA JETSON NANO (PART 2)Image Recognition Using Edge Impulse ELEKTOR JUMPSTARTER NEWSUpcoming Campaigns AN OPEN-SOURCE GPS TRACKING PLATFORMTraccar Maps Vehicle Tracking Without the Need for a Third-Party Cloud Server JOY-IT LCR-T7 MULTI-FUNCTION TESTERTesting Passives, Discrete Semiconductors and IR Remote Controls NOISE SYNTHESIZERFrom Noise to Music with the PRBSynth1 STARTING OUT IN ELECTRONICSEasier than Imagined! ... Continuing with the Coil UNDERSTANDING THE NEURONS IN NEURAL NETWORKS (PART 2)Logical Neurons ISSUES WITH SECURITY? FIGHT FIRE WITH FIRE!Flashbulb-Protected Analogue Memory Add-on For the Tamper-Evident Box LCR METER POSTER BLUETOOTH BEACONS IN PRACTICEBeacons Light the Way Ahead C PROGRAMMING ON RASPBERRY PICommunicating over Wi-Fi (Sample Chapter) EMC PRE-COMPLIANCE TEST FOR YOUR DC-POWERED PROJECT (PART 2)The Hardware and How to Use It HANDS ON THE PARALLAX PROPELLER 2 (PART 5)Inside the Smart Pin MODBUS OVER WLAN (PART 1)Hardware and Programming HOMELAB TOURSWhere the Junior Computer Is Brought to Life Again BUILD YOUR OWN HIGH-PRECISION CALIBRATOR-10 V to +10 V, 0 to 40 mA, 0.001% ARDUINO NANO RP2040 CONNECTRaspberry Pi RP2040 + Wi-Fi + Bluetooth THE PHYSICAL BODY OF ARTIFICIAL INTELLIGENCE ERR-LECTRONICSCorrections, Updates and Readers’ Letters CREATE GUIS WITH PYTHONIntroducing guizero CO2 METER KIT FOR THE CLASSROOMAn ESP8266-Based Device from the University of Applied Sciences Aachen NOSTALGIC MK484 MW/LW RADIO...Always Fun to Build! ELEKTOR @ 60Let There Be Light! HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2021_en.png?v=1707314591https://www.elektor.com/products/elektor-november-december-2021-en?variant=47666422350156 in stock 10.95 109 4.9 6.9 2 - 4 Werktage 47666422907212 Elektor November/December 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666422907212-has-digital-downloads - IMAGE PROCESSING WITH THE NVIDIA JETSON NANO (PART 2)Image Recognition Using Edge Impulse ELEKTOR JUMPSTARTER NEWSUpcoming Campaigns AN OPEN-SOURCE GPS TRACKING PLATFORMTraccar Maps Vehicle Tracking Without the Need for a Third-Party Cloud Server JOY-IT LCR-T7 MULTI-FUNCTION TESTERTesting Passives, Discrete Semiconductors and IR Remote Controls NOISE SYNTHESIZERFrom Noise to Music with the PRBSynth1 STARTING OUT IN ELECTRONICSEasier than Imagined! ... Continuing with the Coil UNDERSTANDING THE NEURONS IN NEURAL NETWORKS (PART 2)Logical Neurons ISSUES WITH SECURITY? FIGHT FIRE WITH FIRE!Flashbulb-Protected Analogue Memory Add-on For the Tamper-Evident Box LCR METER POSTER BLUETOOTH BEACONS IN PRACTICEBeacons Light the Way Ahead C PROGRAMMING ON RASPBERRY PICommunicating over Wi-Fi (Sample Chapter) EMC PRE-COMPLIANCE TEST FOR YOUR DC-POWERED PROJECT (PART 2)The Hardware and How to Use It HANDS ON THE PARALLAX PROPELLER 2 (PART 5)Inside the Smart Pin MODBUS OVER WLAN (PART 1)Hardware and Programming HOMELAB TOURSWhere the Junior Computer Is Brought to Life Again BUILD YOUR OWN HIGH-PRECISION CALIBRATOR-10 V to +10 V, 0 to 40 mA, 0.001% ARDUINO NANO RP2040 CONNECTRaspberry Pi RP2040 + Wi-Fi + Bluetooth THE PHYSICAL BODY OF ARTIFICIAL INTELLIGENCE ERR-LECTRONICSCorrections, Updates and Readers’ Letters CREATE GUIS WITH PYTHONIntroducing guizero CO2 METER KIT FOR THE CLASSROOMAn ESP8266-Based Device from the University of Applied Sciences Aachen NOSTALGIC MK484 MW/LW RADIO...Always Fun to Build! ELEKTOR @ 60Let There Be Light! HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2021-pdf_en.png?v=1707314602https://www.elektor.com/products/elektor-november-december-2021-pdf-en?variant=47666422907212 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666423529804 Elektor November/December 2022 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0517 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.High-End from the Elektor LabFortissimo-100 High-End AmplifierFully symmetrical audio output stage and 100/190 WChecking the Frequency of Tuned Circuits and CrystalsTips & Tricks, Best Practices and Other Useful InformationPCB Tips and TricksSoldering – So What?A Closer Look at Current Soldering TechnologyLow-Latency Bluetooth Garage Door ControlTake Control with Short BLE Messages from a SmartphoneIdeal Diode ControllerDiode Circuits with Low Power DissipationLED Garlands with ESP32 and FreeRTOSFlashing and Variable BrightnessStarting Out in Electronics……Cheerfully Continues ZeneringFM/DAB+ ReceiverThe Best of Both WorldsFrom Life’s ExperienceElectronica ObscuraTracing the Cause of Software Bugs WirelesslyCircular Buffer and Webserver on the ESP32Did Covid Cause a Boost in Engineering Innovation?Innovative Components and Solutions from 2022Ersa i-CON TRACE – The IoT Soldering Station for MakersInfographicsWhat Are We Going to Do with All This Compute?How to Drive Ynvisible’s E-Paper DisplayAll-Time Innovation with InnoFaithQ&A with Walter ArkesteijnIndustrial AutomationEasy and scalable IoT-RetrofittingNext Generation Oscilloscopes for Accelerated InsightRohde & Schwarz introduces the R&S MXO 4 seriesLow Profile Linear Connectors Solve Multi-Signal Data ManagementSmart – Innovative – Cost-EfficientGateMate FPGAs Developed and Manufactured in GermanyTools to Support Low-Cost Sensor DevelopmentPolyfusesPeculiar Parts, the SeriesIsolated Analog Output for Arduino UnoHomeLab Tours... Discovers the Thereminelectronica fast forward 2022 - powered by ElektorLineup and TimetableRadio Direction FindingTracking Down Lost Wireless Weather SensorsEstimate an IC's Internal NoiseA Simple MethodEthics in ActionPowered by WEEFNo Ethics, No Sustainable BusinessAn Interview with Professor Stefan HeinemannThe 2023 WEEF IndexFilter SoftwareDesign Tools for Analog FiltersTV-B-Gone!... Or At Least B-OFFRP2040-Based Air Quality MeasurementelekterminalKickstart to Python 3Sample Chapter: Digital Image Processing and Wand LibrarySOLARPUNKA Brighter Future AheadHexadoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2022_en.png?v=1707314615https://www.elektor.com/products/elektor-november-december-2022-en?variant=47666423529804 in stock 10.95 84 4.9 6.9 2 - 4 Werktage 46907275706700 Elektor November/December 2022 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0675 Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.High-end uit het Elektor-labFortissimo-100 high-end versterkervolledig symmetrische audio-eindtrap levert 100/190 WControleer de frequentie van afgestemde kringen en kristallenPrinten ontwerpentips en trucsSolderen – nou en?moderne soldeertechnologie nader bekekenBluetooth-garagedeurbediening met geringe latentiemet korte BLE-berichten vanaf een smartphoneIdeale diode-controllerdiodeschakelingen met geringe vermogensdissipatieLED-slingers met ESP32 en FreeRTOSknipperen dat het een lieve lust isAlle begin......zenert er vrolijk op losFM/DAB+ ontvangerhet beste van twee wereldenUit het leven gegrepenelektronica obscuraDe oorzaak van software-bugs draadloos opsporencirculaire buffer en webserver op de ESP32Heeft Covid de innovatie gestimuleerd?innovatieve componenten en oplossingen uit 2022Ersa i-CON TRACEhet IoT-soldeerstation voor makersElektor InfographicsWat moeten we met al die computers?Aansturing van het e-paper display van YnvisibleInnoFaith: innovatie en nog eens innovatievraaggesprek met Walter ArkesteijnIndustriële automatiseringeenvoudige en schaalbare IoT-retrofittingReed-relaisvreemde onderdelenLow-profile lineaire connectorenvereenvoudigen multisignaal-databeheerSlim – Innovatief – KosteneffectiefGateMate FPGA’s worden ontwikkeld en geproduceerd in DuitslandTools voor de ontwikkeling van goedkope sensorenPolyfusesvreemde onderdelenGeïsoleerde analoge uitgang voor Arduino UnoOost West Lab Best...ontdekt de Thereminelectronica fast forward 2022 – powered by Elektorde deelnemers en het programmaRadiorichtingzoekerspoor verloren weersensoren opSchat de interne ruis van een ICeen eenvoudige methodeEthiek in actiepowered by WEEFZonder ethiek geen duurzaam ondernemenvraaggesprek met professor Stefan HeinemannDe WEEF Index 2023Filtersoftwareontwerp-tools voor analoge filtersTV-B-Gone!...of tenminste TV tabeeMeting van de luchtkwaliteitop basis van de RP2040elekterminalSnelstart met Python 3voorbeeldhoofdstuk: digitale beeldbewerking en de Wand-bibliotheekSOLARPUNKeen mooiere toekomst in het verschietHexadoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2022_nl.png?v=1689092901https://www.elektor.com/products/elektor-november-december-2022-nl?variant=46907275706700 in stock 14.95 58 4.9 6.9 2 - 4 Werktage 47666427363660 Elektor November/December 2022 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666427363660-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.High-End from the Elektor LabFortissimo-100 High-End AmplifierFully symmetrical audio output stage and 100/190 WChecking the Frequency of Tuned Circuits and CrystalsTips & Tricks, Best Practices and Other Useful InformationPCB Tips and TricksSoldering – So What?A Closer Look at Current Soldering TechnologyLow-Latency Bluetooth Garage Door ControlTake Control with Short BLE Messages from a SmartphoneIdeal Diode ControllerDiode Circuits with Low Power DissipationLED Garlands with ESP32 and FreeRTOSFlashing and Variable BrightnessStarting Out in Electronics……Cheerfully Continues ZeneringFM/DAB+ ReceiverThe Best of Both WorldsFrom Life’s ExperienceElectronica ObscuraTracing the Cause of Software Bugs WirelesslyCircular Buffer and Webserver on the ESP32Did Covid Cause a Boost in Engineering Innovation?Innovative Components and Solutions from 2022Ersa i-CON TRACE – The IoT Soldering Station for MakersInfographicsWhat Are We Going to Do with All This Compute?How to Drive Ynvisible’s E-Paper DisplayAll-Time Innovation with InnoFaithQ&A with Walter ArkesteijnIndustrial AutomationEasy and scalable IoT-RetrofittingNext Generation Oscilloscopes for Accelerated InsightRohde & Schwarz introduces the R&S MXO 4 seriesLow Profile Linear Connectors Solve Multi-Signal Data ManagementSmart – Innovative – Cost-EfficientGateMate FPGAs Developed and Manufactured in GermanyTools to Support Low-Cost Sensor DevelopmentPolyfusesPeculiar Parts, the SeriesIsolated Analog Output for Arduino UnoHomeLab Tours... Discovers the Thereminelectronica fast forward 2022 - powered by ElektorLineup and TimetableRadio Direction FindingTracking Down Lost Wireless Weather SensorsEstimate an IC's Internal NoiseA Simple MethodEthics in ActionPowered by WEEFNo Ethics, No Sustainable BusinessAn Interview with Professor Stefan HeinemannThe 2023 WEEF IndexFilter SoftwareDesign Tools for Analog FiltersTV-B-Gone!... Or At Least B-OFFRP2040-Based Air Quality MeasurementelekterminalKickstart to Python 3Sample Chapter: Digital Image Processing and Wand LibrarySOLARPUNKA Brighter Future AheadHexadoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2022-pdf_en.png?v=1707314625https://www.elektor.com/products/elektor-november-december-2022-pdf-en?variant=47666427363660 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 46907267842380 Elektor November/December 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines has-digital-downloads,variant-46907267842380-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.High-end uit het Elektor-labFortissimo-100 high-end versterkervolledig symmetrische audio-eindtrap levert 100/190 WControleer de frequentie van afgestemde kringen en kristallenPrinten ontwerpentips en trucsSolderen – nou en?moderne soldeertechnologie nader bekekenBluetooth-garagedeurbediening met geringe latentiemet korte BLE-berichten vanaf een smartphoneIdeale diode-controllerdiodeschakelingen met geringe vermogensdissipatieLED-slingers met ESP32 en FreeRTOSknipperen dat het een lieve lust isAlle begin......zenert er vrolijk op losFM/DAB+ ontvangerhet beste van twee wereldenUit het leven gegrepenelektronica obscuraDe oorzaak van software-bugs draadloos opsporencirculaire buffer en webserver op de ESP32Heeft Covid de innovatie gestimuleerd?innovatieve componenten en oplossingen uit 2022Ersa i-CON TRACEhet IoT-soldeerstation voor makersElektor InfographicsWat moeten we met al die computers?Aansturing van het e-paper display van YnvisibleInnoFaith: innovatie en nog eens innovatievraaggesprek met Walter ArkesteijnIndustriële automatiseringeenvoudige en schaalbare IoT-retrofittingReed-relaisvreemde onderdelenLow-profile lineaire connectorenvereenvoudigen multisignaal-databeheerSlim – Innovatief – KosteneffectiefGateMate FPGA’s worden ontwikkeld en geproduceerd in DuitslandTools voor de ontwikkeling van goedkope sensorenPolyfusesvreemde onderdelenGeïsoleerde analoge uitgang voor Arduino UnoOost West Lab Best...ontdekt de Thereminelectronica fast forward 2022 – powered by Elektorde deelnemers en het programmaRadiorichtingzoekerspoor verloren weersensoren opSchat de interne ruis van een ICeen eenvoudige methodeEthiek in actiepowered by WEEFZonder ethiek geen duurzaam ondernemenvraaggesprek met professor Stefan HeinemannDe WEEF Index 2023Filtersoftwareontwerp-tools voor analoge filtersTV-B-Gone!...of tenminste TV tabeeMeting van de luchtkwaliteitop basis van de RP2040elekterminalSnelstart met Python 3voorbeeldhoofdstuk: digitale beeldbewerking en de Wand-bibliotheekSOLARPUNKeen mooiere toekomst in het verschietHexadoku https://www.elektor.com/cdn/shop/files/elektor-11-12-2022-pdf_nl.png?v=1689092694https://www.elektor.com/products/elektor-november-december-2022-pdf-nl?variant=46907267842380 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47666429886796 Elektor November/December 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0525 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.The Raspberry Pi 5A Huge Improvement From Its PredecessorAI in the Electronics LabGoogle Bard and Flux Copilot Put to the TestArduino Nano Waveform GeneratorNano + Code = Function GeneratorSolar-Powered Christmas GarlandAn Eco-Friendly Solution for Garnishing Your BalconyUSB Killer DetectorBetter Safe Than SorryA Simple CNCed EnclosureWith Autodesk Fusion 360 for Personal UseLow-Volume Board ProductionWith and without AssemblyIoT Simulation Simplified with WokwiDeveloper Uri Shaked on Design, Software, and MoreA Bare-Metal Programming Guide (Part 3)CMSIS Headers, Automatic Testing, and a Web ServerLoRa, a Swiss Army Knife (2)The Hardware and SoftwareMEMS Microphone Design and ConstructionTools to Try Before You SolderSimulation and 3D Modeling Tools That Can Be Used for FreeNew Tools From Microchip!PICkit 5 and MPLAB ICD 5 Available Now!Rapid Prototyping of Flexible, Stretchable ElectronicsHow the Voltera NOVA Speeds Up Innovation in Wearable Electronic SystemsGalvanic IsolationUsing Phototransistor Optocouplers SuccessfullyThe Complex Solution or the Anybus Solution?Embedded Industrial Ethernet in 2 Days Rather Than Many MonthsYour Essential DFM ChecklistHow to Start Designing for Manufacture3D Printing FilamentsTypes, Features and Use in PrototypingSpecialists for Effective Signal Analysis from ELF to EHF BandAaronia’s latest real-time SPECTRAN® V6 series spectrum analyzersChallenges of DFM Analysis for Flex and Rigid-Flex DesignSetting Up an SMT LineThe Right Combination for a Reliable AssemblyRevolutionizing IndustriesThe Rise of Autonomous Mobile Robots (AMRs)Evolved for More ChallengesRohde & Schwarz Adds Eight-Channel R&S MXO 5 to Next-Generation OscilloscopesStarting Out in Electronics……Amplifying DifferencesMini Reflow PlateFor Assembling or Repairing Small SMD CircuitsDon’t Start with a Prototype – Start with a Pretotype!Check That a Market Exists for Your Product Before Warming Your Soldering Iron2023: An AI OdysseyGetting Help Designing a Physical Project Brussels Is InnovatingSupport for Deep Tech https://www.elektor.com/cdn/shop/files/elektor-11-12-2023_en.png?v=1707314638https://www.elektor.com/products/elektor-november-december-2023-en?variant=47666429886796 in stock 10.95 35 4.9 6.9 2 - 4 Werktage 47666430509388 Elektor November/December 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666430509388-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.The Raspberry Pi 5A Huge Improvement From Its PredecessorAI in the Electronics LabGoogle Bard and Flux Copilot Put to the TestArduino Nano Waveform GeneratorNano + Code = Function GeneratorSolar-Powered Christmas GarlandAn Eco-Friendly Solution for Garnishing Your BalconyUSB Killer DetectorBetter Safe Than SorryA Simple CNCed EnclosureWith Autodesk Fusion 360 for Personal UseLow-Volume Board ProductionWith and without AssemblyIoT Simulation Simplified with WokwiDeveloper Uri Shaked on Design, Software, and MoreA Bare-Metal Programming Guide (Part 3)CMSIS Headers, Automatic Testing, and a Web ServerLoRa, a Swiss Army Knife (2)The Hardware and SoftwareMEMS Microphone Design and ConstructionTools to Try Before You SolderSimulation and 3D Modeling Tools That Can Be Used for FreeNew Tools From Microchip!PICkit 5 and MPLAB ICD 5 Available Now!Rapid Prototyping of Flexible, Stretchable ElectronicsHow the Voltera NOVA Speeds Up Innovation in Wearable Electronic SystemsGalvanic IsolationUsing Phototransistor Optocouplers SuccessfullyThe Complex Solution or the Anybus Solution?Embedded Industrial Ethernet in 2 Days Rather Than Many MonthsYour Essential DFM ChecklistHow to Start Designing for Manufacture3D Printing FilamentsTypes, Features and Use in PrototypingSpecialists for Effective Signal Analysis from ELF to EHF BandAaronia’s latest real-time SPECTRAN® V6 series spectrum analyzersChallenges of DFM Analysis for Flex and Rigid-Flex DesignSetting Up an SMT LineThe Right Combination for a Reliable AssemblyRevolutionizing IndustriesThe Rise of Autonomous Mobile Robots (AMRs)Evolved for More ChallengesRohde & Schwarz Adds Eight-Channel R&S MXO 5 to Next-Generation OscilloscopesStarting Out in Electronics……Amplifying DifferencesMini Reflow PlateFor Assembling or Repairing Small SMD CircuitsDon’t Start with a Prototype – Start with a Pretotype!Check That a Market Exists for Your Product Before Warming Your Soldering Iron2023: An AI OdysseyGetting Help Designing a Physical Project Brussels Is InnovatingSupport for Deep Tech https://www.elektor.com/cdn/shop/files/elektor-11-12-2023-pdf_en.png?v=1707314649https://www.elektor.com/products/elektor-november-december-2023-pdf-en?variant=47666430509388 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47318771073356 Elektor One-armed Bandit Kit Elektor Labs Boards&Kits Bestsellers > Elektor Products > NEW > No Member Discount > Sale 7442105132126 Pull Down Lever For Highest Score! This Elektor Circuit Classic from 1984 shows a playful application of CMOS 400x series logic ICs in combination with LEDs, a highly popular combination at the time. The project imitates a spinning-digit type slot machine. The Game To play the game, first agree on the number of rounds. Player 1 actuates the switch lever as long as desired and releases it. The LEDs then show the score which is the sum of the 50-20-10-5 digits lit up. If the Play Again! LED lights, Player 1 has another, “free” round. If not, it’s Player 2’s turn. The players keep tab of their scores, and the highest score wins. Features LEDs Indicate Score Multi-Player and Play Again! Elektor Heritage Circuit Symbols Tried & Tested by Elektor Labs Educational & Geeky Project Through-Hole Parts Only Included Printed Circuit Board All Components Wooden Stand Bill of Materials Resistors (5%, 250 mW) R1,R2,R3,R4 = 100kΩ R5,R6,R7,R8,R9,R10 = 1kΩ Capacitors C1 = 4.7nF, 10%, 50V, 5mm C2 = 4.7μF, 10%, 63V, axial C3,C4 = 100nF, 10 %, 50V, ceramic X7R, 5mm Semiconductors LED1-LED6 = red, 5mm (T1 3/4) IC1 = 74HC4024 IC2 = 74HC132 Miscellaneous S1 = switch, toggle, 21mm lever, SPDT, momentary S2 = switch, tactile, 24V, 50mA, 6x6mm S3 = switch, slide, SPDT IC1,IC2 = IC socket, DIP14 BT1 = PCB-mount CR2032 battery retainer clip Desktop Stand PCB 230098-1 Not included: BT1 = CR2032 coin cell battery https://www.elektor.com/cdn/shop/files/elektor-one-armed-bandit-kit.png?v=1699464679https://www.elektor.com/products/elektor-one-armed-bandit-kit?variant=47318771073356 in stock 39.95 33.95 121 4.9 6.9 2 - 4 Werktage 46912376045900 Elektor PDF-bundel Elektor Digital Bundels Bestsellers has-digital-downloads,variant-46912376045900-has-digital-downloads Deze Elektor E-Book (pdf) inspiratie bundel bestaat uit:Elektor Magazine, januari/februari 2017 (132 pagina's)Elektor E-Book: Raspberry Pi Compilatie 2 (150 pagina's)Elektor Business - IoT and Industry (36 pagina's)Als u zich inschrijft voor onze Elektor. nieuwsbrief e.zine, ontvangt u van ons een coupon code. Wanneer u deze code gebruikt bij het afrekenen van deze E-Book inspiratie bundel, wordt deze gratis! Meer informatie over het gebruiken van coupon codes vind je hier. https://www.elektor.com/cdn/shop/files/nl-magazine-bundle.png?v=1699543388https://www.elektor.com/cdn/shop/files/nl-magazine-bundle_1.png?v=1699543388https://www.elektor.com/products/elektor-pdf-bundel?variant=46912376045900 in stock 29.85 0 4.9 6.9 2 - 4 Werktage 46907277246796 Elektor Raspberry Pi Buffer Board Elektor Labs Boards&Kits Bestsellers > NEW > Raspberry Pi > Raspberry Pi Accessories > Sale 7442105131112 When you experiment with the Raspberry Pi on a regular basis and you connect a variety of external hardware to the GPIO port via the header you may well have caused some damage in the past. The Raspberry Pi Buffer Board is there to prevent this! The board is compatible with Raspberry Pi Zero, 3, 4, 5 and 400.All 26 GPIOs are buffered with bi-directional voltage translators to protect the Raspberry Pi when experimenting with new circuits. The PCB is intended to be inserted in the back of Raspberry Pi< 400. The connector to connect to the Raspberry Pi is a right angled 40-way receptacle (2x20). The PCB is only a fraction wider. A 40-way flat cable with appropriate 2x20 headers can be connected to the buffer output header to experiment for instance with a circuit on a breadboard or PCB.The circuit uses four TXS0108E ICs by Texas Instruments. The PCB can also be put upright on a Raspberry Pi 3 or newer.DownloadsSchematicsLayout https://www.elektor.com/cdn/shop/files/raspberry-pi-400-buffer-board.png?v=1689092956https://www.elektor.com/cdn/shop/files/raspberry-pi-400-buffer-board_front.png?v=1696854842,https://www.elektor.com/cdn/shop/files/raspberry-pi-400-buffer-board_connected.png?v=1696854842https://www.elektor.com/products/elektor-raspberry-pi-buffer-board?variant=46907277246796 in stock 29.95 22.95 90 4.9 6.9 2 - 4 Werktage 46907118092620 Elektor Raspberry Pi RTL-SDR V3 Bundle (EN) Elektor Bundles Bundels Books > Bundles > No Member Discount > Radio | SDR 7442105130153 Although much classical HF and mobile equipment is still in use by many amateurs, the use of computers and digital techniques has now become very popular among amateur radio operators. Nowadays, anyone can purchase a Raspberry Pi computer and run almost all amateur radio software on the ‘RPi’, which is slightly bigger than the size of a credit card. The RTL-SDR devices have become very popular among hams because of their very low cost and rich features. A basic system may consist of a USB-based RTL-SDR device (dongle) with a suitable antenna, an RPi computer, a USB-based external audio input-output adapter, and software installed on the Pi. With such a simple setup it is feasible to receive signals from around 24 MHz to over 1.7 GHz. With the addition of a low-cost upconverter device, an RTL-SDR can easily and effectively receive the HF bands. This book is aimed at amateur radio enthusiasts, electronic engineering students, and anyone interested in learning to use the Raspberry Pi to build electronic projects. The book is suitable for the full range of beginners through old hands at ham radio. Step-by-step installation of the operating system is described with many details on the commonly used Linux commands. Some knowledge of the Python programming language is required to understand and modify the projects given in the book. Example projects developed in the book include a station clock, waveform generation, transistor amplifier design, active filter design, Morse code exerciser, frequency counter, RF meter, and more. The block diagram, circuit diagram, and complete Python program listings are given for each project, including the full description of the projects. Besides wide coverage of RTL-SDR for amateur radio, the book also summarizes the installation and use instructions of the following ham radio programs and software tools you can run on your Raspberry Pi: TWCLOCK, Klog, Gpredict, FLDIGI, DIRE WOLF, xcwcp, QSSTV, LinPsk, Ham Clock, CHIRP, xastir, and CQRLOG. The RTL-SDR kit includes RTL-SDR Blog brand R820T2 RTL2832U 1PPM TCXO SMA V3 Dongle Dipole Antenna Base with 60 cm RG174 extension cable 2x 23 cm to 1 m telescopic antenna 2x 5 cm to 13 cm telescopic antenna 3 meter RG174 extension cable Flexible Tripod Mount Suction Cup Mount RTL-SDR is an affordable dongle that can be used as a computer based radio scanner for receiving live radio signals in your area. This particular dongle includes a R820T2 tuner, a 1 PPM temperature compensated oscillator (TCXO), SMA F connector. It features an aluminium case with passive cooling via a thermal pad. Moreover, there is a software switchable bias tee circuit, supplementary ESD protection, lower overall noise and built-in direct sampling for HF reception. This device can receive frequencies from 500 kHz to 1.7 GHz and has up to 3.2 MHz of instantaneous bandwidth (2.4 MHz stable). Note: RTL-SDR dongles are RX only. You can use this kit either for terrestrial or satellite reception just by changing the orientation of the antenna. Thanks to the included mounts and extension cables it is possible to temporarily place the antenna outside for a better reception. Other potential applications are general radio scanning, air traffic control, public safety radio, ADSB, ACARS, trunked radio, P25 digital voice, POCSAG, weather balloons, APRS, NOAA APT weather satellites, radio astronomy, meteor scatter monitoring etc. https://www.elektor.com/cdn/shop/files/elektor-raspberry-pi-rtl-sdr-bundle-en.jpg?v=1689087688https://www.elektor.com/cdn/shop/files/elektor_raspberry_pi_rtl-sdr_kit_book.png?v=1696851247,https://www.elektor.com/cdn/shop/files/elektor_raspberry_pi_rtl-sdr_kit_rtl-sdr-kit.jpg?v=1696851247,https://www.elektor.com/cdn/shop/files/elektor-raspberry-pi-rtl-sdr-kit_rtl-sdr.jpg?v=1698679489https://www.elektor.com/products/elektor-raspberry-pi-rtl-sdr-bundle?variant=46907118092620 out of stock 94.95 79.95 0 0 6.9 nicht auf Lager 47400726004044 Elektor Raspberry Pi RTL-SDR V4 Bundle Elektor Bundles Bundels Bestsellers > Bundles > NEW > No Member Discount > Radio | SDR 020737 Program and build Raspberry Pi based ham station utilities, tools, and instruments The new improved RTL-SDR V4 allows you to receive radio signals between 500 kHz and 1.75 GHz from stations utilizing different bands including MW/SW/LW broadcast, ham radio, utility, air traffic control, PMR, SRD, ISM, CB, weather satellite, and radio astronomy. The book Raspberry Pi for Radio Amateurs gives extensive coverage of deploying the RTL-SDR kit through the use of a Raspberry Pi. This bundle contains: RTL-SDR V4 (Software Defined Radio) with Dipole Antenna Kit (normal price: €59.95) Raspberry Pi for Radio Amateurs (normal price: €34.95) RTL-SDR V4 (Software Defined Radio) with Dipole Antenna Kit RTL-SDR is an affordable dongle that can be used as a computer-based radio scanner for receiving live radio signals between 500 kHz and 1.75 GHz in your area. The new RTL-SDR V4 offers several improvements over generic brands including use of the R828D tuner chip, triplexed input filter, notch filter, improved component tolerances, a 1 PPM temperature compensated oscillator (TCXO), SMA F connector, aluminium case with passive cooling, bias tee circuit, improved power supply, and a built in HF upconverter. RTL-SDR V4 comes with the portable dipole antenna kit. It is great for beginners as it allows for terrestrial and satellite reception and easy to mount outdoors and designed for portable and temporary outside usage. Features Improved HF reception: V4 now uses a built-in upconverter instead of using a direct sampling circuit. This means no more Nyquist folding of signals around 14.4 MHz, improved sensitivity, and adjustable gain on HF. Like the V3, the lower tuning range remains at 500 kHz and very strong reception may still require front end attenuation/filtering. Improved filtering: The V4 makes use of the R828D tuner chip, which has three inputs. The SMA input has been triplexed input into 3 bands: HF, VHF and UHF. This provides some isolation between the 3 bands, meaning out of band interference from strong broadcast stations is less likely to cause desensitization or imaging. Improved filtering x2: In addition to the triplexing, the open drain pin on the R828D can be also used, which allows to add simple notch filters for common interference bands such as broadcast AM, broadcast FM and the DAB bands. These only attenuate by a few dB, but may still help. Improved phase noise on strong signals: Due to an improved power supply design, phase noise from power supply noise has been significantly reduced. Less heat: Another advantage of the improved power supply is low power consumption and less heat generation compared to the V3. Contents 1x RTL-SDR V4 dongle (R828D RTL2832U 1PPM TCXO SMA) 2x 23 cm to 1 m telescopic antenna 2x 5 cm to 13 cm telescopic antenna 1x Dipole antenna base with 60 cm RG174 1x 3 m RG174 extension cable 1x Flexible tripod mount 1x Suction cup mount Links User Guide Quick Start Guide SDR# User Guide Dipole Antenna Guide Raspberry Pi for Radio Amateurs Although much classical HF and mobile equipment is still in use by many amateurs, the use of computers and digital techniques has now become very popular among amateur radio operators. Nowadays, anyone can purchase a Raspberry Pi computer and run almost all amateur radio software on the ‘RPi’, which is slightly bigger than the size of a credit card. The RTL-SDR devices have become very popular among hams because of their very low cost and rich features. A basic system may consist of a USB-based RTL-SDR device (dongle) with a suitable antenna, an RPi computer, a USB-based external audio input-output adapter, and software installed on the Pi. With such a simple setup it is feasible to receive signals from around 24 MHz to over 1.7 GHz. With the addition of a low-cost upconverter device, an RTL-SDR can easily and effectively receive the HF bands. This book is aimed at amateur radio enthusiasts, electronic engineering student... https://www.elektor.com/cdn/shop/files/Elektor-Raspberry-Pi-RTL-SDR-V4-Bundle-EN.jpg?v=1701265769https://www.elektor.com/cdn/shop/files/Elektor-Raspberry-Pi-RTL-SDR-V4-Bundle-EN_kit.jpg?v=1701265769,https://www.elektor.com/cdn/shop/files/Elektor-Raspberry-Pi-RTL-SDR-V4-Bundle-EN_book.png?v=1701265770https://www.elektor.com/products/elektor-raspberry-pi-rtl-sdr-v4-bundle-en?variant=47400726004044 in stock 94.95 79.95 27 0 6.9 2 - 4 Werktage 46906990526796 Elektor SDR Shield 2.0 Elektor Labs Boards&Kits Arduino > Arduino Shields > Bestsellers > Elektor Modules > Elektor PCBs > Elektor Products > Radio | SDR > Sale 018515 This board is a newer version of the Elektor SDR Reloaded, the difference is that on this new version with two PLL outputs and two LF-outputs, which are accessible via additional connectors on the board (not included in the kit). This allows the user to use this Arduino shield as a signal generator, SW transmitter or even transceiver. Specifications Operating Voltage 5 V and 3.3 V from Arduino Frequency Range 150 kHz to 30 MHz Sensitivity 1 µV Overall Gain 40 dB Maximum signal level at antenna 10 mV Dynamic Range 80 dB Please note: The module doesn't come pre-soldered. Links Elektor SDR Shield 2.0 (1) Elektor SDR Shield 2.0 (2) Elektor SDR Shield 2.0 (3) https://www.elektor.com/cdn/shop/files/18515_-_160577-52-resized.jpg?v=1698679516https://www.elektor.com/cdn/shop/files/18515_-_160577-13-resized.jpg?v=1698679516,https://www.elektor.com/cdn/shop/files/18515_-_160577-51c-resized.jpg?v=1698679516,https://www.elektor.com/cdn/shop/files/170515-sdr-shield-no-connectors.jpg?v=1698679516,https://www.elektor.com/cdn/shop/files/img_8018.jpg?v=1698679516https://www.elektor.com/products/elektor-sdr-shield-2-0?variant=46906990526796 in stock 39.95 29.95 19 4.9 6.9 2 - 4 Werktage 47571358384460 Elektor September/October 2020 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47571358384460-has-digital-downloads - Elektor Magazine EN September/October 2020 (PDF) https://www.elektor.com/cdn/shop/files/elektor-09-10-2020-pdf_en.png?v=1705320641https://www.elektor.com/products/elektor-september-october-2020-pdf-en?variant=47571358384460 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666431426892 Elektor September/October 2021 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0509 UNDERSTANDING THE NEURONS IN NEURAL NETWORKS (PART 1)Artificial Neurons EMC PRE-COMPLIANCE TEST FOR YOUR DC-POWERED PROJECT (PART 1)Dual DC LISN ELECTRONIC LOAD FOR DC AND ACUp to 400 V and 10 A (Peak) STARTING OUT IN ELECTRONICSEasier Than Imagined! ...Taking on the Choke! IMAGE PROCESSING WITH THE NVIDIA JETSON NANO (PART 1)The Hardware and Software AN IN-DEPTH LOOK AT MAINS TRANSFORMERSHow Do They Behave When They Are Switched On and Off? YES WE CAN WITH PICAN 3A CAN Bus HAT for the Raspberry Pi 4 BALCONY POWER PLANTDIY Solar Balcony = Speedy Payback! IMAGING AND VIDEO-STREAMING WITH A RASPBERRY PI 4The Raspberry Pi High-Quality Camera in Practice USING DISPLAYS IN RASPBERRY PI PROJECTSSample Chapter: Organic Light Emitting Diode Displays (OLED) HANDS ON THE PARALLAX PROPELLER 2 (PART 4)Sending Strings ELEKTOR @ 60A Look Back at Previous Septembers HOMELAB TOURSIn the Friesian Countryside, Where the Tubes Bloom ... HYBRIDSPeculiar Parts, the series A COMPASS ROSE USING THE GY-271Or Why We Move in Figures of Eight to Calibrate a Sensor FINDING YOUR FOOTPRINTCalculate the Carbon Footprint of Your Electronics ESP32-CONNECTED THERMOSTATKeep Your Wine at the Right Temperature! MAGNETIC LEVITATION THE DIGITAL WAYESP32 Pico Replaces the Analog Comparator ULTIMATE ARDUINO UNO HARDWARE MANUALSample Chapter: Main Microcontroller Bootloader MICROPYTHON FOR THE ESP32 AND FRIENDS (PART 2)Control Matrix Displays Easily MADMACHINE SWIFTIO BOARDModern Language Meets Modern Hardware FROM LIFE’S EXPERIENCEOn-Again, Off-Again Relationship HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2021_en.png?v=1707314661https://www.elektor.com/products/elektor-september-october-2021-en?variant=47666431426892 in stock 10.95 86 4.9 6.9 2 - 4 Werktage 47666432999756 Elektor September/October 2021 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666432999756-has-digital-downloads - UNDERSTANDING THE NEURONS IN NEURAL NETWORKS (PART 1)Artificial Neurons EMC PRE-COMPLIANCE TEST FOR YOUR DC-POWERED PROJECT (PART 1)Dual DC LISN ELECTRONIC LOAD FOR DC AND ACUp to 400 V and 10 A (Peak) STARTING OUT IN ELECTRONICSEasier Than Imagined! ...Taking on the Choke! IMAGE PROCESSING WITH THE NVIDIA JETSON NANO (PART 1)The Hardware and Software AN IN-DEPTH LOOK AT MAINS TRANSFORMERSHow Do They Behave When They Are Switched On and Off? YES WE CAN WITH PICAN 3A CAN Bus HAT for the Raspberry Pi 4 BALCONY POWER PLANTDIY Solar Balcony = Speedy Payback! IMAGING AND VIDEO-STREAMING WITH A RASPBERRY PI 4The Raspberry Pi High-Quality Camera in Practice USING DISPLAYS IN RASPBERRY PI PROJECTSSample Chapter: Organic Light Emitting Diode Displays (OLED) HANDS ON THE PARALLAX PROPELLER 2 (PART 4)Sending Strings ELEKTOR @ 60A Look Back at Previous Septembers HOMELAB TOURSIn the Friesian Countryside, Where the Tubes Bloom ... HYBRIDSPeculiar Parts, the series A COMPASS ROSE USING THE GY-271Or Why We Move in Figures of Eight to Calibrate a Sensor FINDING YOUR FOOTPRINTCalculate the Carbon Footprint of Your Electronics ESP32-CONNECTED THERMOSTATKeep Your Wine at the Right Temperature! MAGNETIC LEVITATION THE DIGITAL WAYESP32 Pico Replaces the Analog Comparator ULTIMATE ARDUINO UNO HARDWARE MANUALSample Chapter: Main Microcontroller Bootloader MICROPYTHON FOR THE ESP32 AND FRIENDS (PART 2)Control Matrix Displays Easily MADMACHINE SWIFTIO BOARDModern Language Meets Modern Hardware FROM LIFE’S EXPERIENCEOn-Again, Off-Again Relationship HEXADOKUThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2021-pdf_en.png?v=1707314672https://www.elektor.com/products/elektor-september-october-2021-pdf-en?variant=47666432999756 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666433851724 Elektor September/October 2022 Elektor Magazines/Specials Bestsellers > Elektor (Print) EP-0516 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.electronica fast forward 2022 Start- & Scale-Up AwardsPreparations Speeding Up!Bluetooth Low Energy with ESP32-C3 and ESP32You Don’t Always Need to Choose Wi-Fi!Bluetooth Low Energy SnifferHacking a makerdiary nRF52840 MDK USB DongleMagic RGB LED CubeHardware Design Around an RP2040Auto On/Off for Solder Paste CompressorElektor Video ContentLivestreams, Webinars, and Courses for Engineers and Pro MakersBicycle ElectrificationHands-On with an E-Bike Retrofit KitStarting Out in ElectronicsMultiplying VoltagesFrom Life’s ExperienceSidelinesTeensy 4.0Why Is This Board So Fast?Audio Power Amplifier Simulation with TINAThe Try-Before-You-Build ApproachDevelop and Operate Your LoRaWAN IoT NodesSample Chapter: Dragino LHT65, LDS01, and LDS02 LoRaWAN ModulesErr-lectronicsCorrections, Updates and Readers’ Letters5G Just for MeGaining Complete Control of 5G Deployments with Private Cellular NetworksInfographics 7-8/2022How Does My Device Learn to Transmit?Applications with Wi-Fi InterfacesSmartphones are the Heart of the IoTAudio Spectrum Analyzer with DekatronsA New Way to Use Vintage TubesSending Data to TelegramGet It Done with an ESP32 and a Few PartsA Fliege Notch Filter for Audio MeasurementsMake Better Measurements with a Notch FilterCO2 Meter TeardownIs It Hackable for Your Projects?PUT-ting It All TogetherThe Programmable Unijunction Transistor ExplainedRound Touchscreen for Raspberry PiHyperPixel 2.1 Round from PimoroniRemote Sensing with Connection Loss DetectionUsing nRF24L01+ ModulesDigital FM Receiver with Arduino and TEA5767Stayed Tuned with an Arduino NanoChanging an OLED Interface from SPI to I²CHomeLab ToursA Hobby Does Not RetireA Decade of Ethics in ElectronicsTessel Renzenbrink Reflects on the Digital Society and MoreHexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2022_en.png?v=1707314684https://www.elektor.com/products/elektor-september-october-2022-en?variant=47666433851724 in stock 10.95 66 4.9 6.9 2 - 4 Werktage 47666434572620 Elektor September/October 2022 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666434572620-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.electronica fast forward 2022 Start- & Scale-Up AwardsPreparations Speeding Up!Bluetooth Low Energy with ESP32-C3 and ESP32You Don’t Always Need to Choose Wi-Fi!Bluetooth Low Energy SnifferHacking a makerdiary nRF52840 MDK USB DongleMagic RGB LED CubeHardware Design Around an RP2040Auto On/Off for Solder Paste CompressorElektor Video ContentLivestreams, Webinars, and Courses for Engineers and Pro MakersBicycle ElectrificationHands-On with an E-Bike Retrofit KitStarting Out in ElectronicsMultiplying VoltagesFrom Life’s ExperienceSidelinesTeensy 4.0Why Is This Board So Fast?Audio Power Amplifier Simulation with TINAThe Try-Before-You-Build ApproachDevelop and Operate Your LoRaWAN IoT NodesSample Chapter: Dragino LHT65, LDS01, and LDS02 LoRaWAN ModulesErr-lectronicsCorrections, Updates and Readers’ Letters5G Just for MeGaining Complete Control of 5G Deployments with Private Cellular NetworksInfographics 7-8/2022How Does My Device Learn to Transmit?Applications with Wi-Fi InterfacesSmartphones are the Heart of the IoTAudio Spectrum Analyzer with DekatronsA New Way to Use Vintage TubesSending Data to TelegramGet It Done with an ESP32 and a Few PartsA Fliege Notch Filter for Audio MeasurementsMake Better Measurements with a Notch FilterCO2 Meter TeardownIs It Hackable for Your Projects?PUT-ting It All TogetherThe Programmable Unijunction Transistor ExplainedRound Touchscreen for Raspberry PiHyperPixel 2.1 Round from PimoroniRemote Sensing with Connection Loss DetectionUsing nRF24L01+ ModulesDigital FM Receiver with Arduino and TEA5767Stayed Tuned with an Arduino NanoChanging an OLED Interface from SPI to I²CHomeLab ToursA Hobby Does Not RetireA Decade of Ethics in ElectronicsTessel Renzenbrink Reflects on the Digital Society and MoreHexadokuThe Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2022-pdf_en.png?v=1707314695https://www.elektor.com/products/elektor-september-october-2022-pdf-en?variant=47666434572620 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666435457356 Elektor September/October 2023 Elektor Magazines/Specials Elektor (Print) EP-0524 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Raspberry Pi Pico as Spectrum AnalyzerFFTs on a Low-Cost Hardware Basis±40-V Linear Voltage RegulatorAn Alternative Power Supply for the Fortissimo-100 Power Amplifier… and Others!MCU Wireless Communication Made FlexibleEEPROM Opens Networking Prospects for Wireless MCUs€5,000 up for grabs!Join the STM32 Wireless Innovation Design Contest2023: An AI OdysseyGetting Started with ChatGPT’s Code InterpreterLoRa, a Swiss Army Knife (1)The LoRa Protocol and Its AdvantagesAdjustable Current Sink with Integrated Clock GeneratorTest Power Supplies, Voltage Converters and BatteriesTwo New Arduino UNO R4 Boards: Minima and WiFiLogarithmic PotentiometersThey’re Exponential!Motor Driver Breakout BoardA BoB for a 5 A DC Motor Driver with a 3×3 mm SizeFrom Life’s ExperienceHazardous ElectronicsIs Cellular the Lowest-Power Option for IoT?LTE-M and NB-IoT Energy Requirements in LPWAN DeploymentsWireless Communication in IoT Systems – Using Arduino MKR ModulesThe Right Board for Wi-Fi, LoRa, and Many More StandardsAC Losses in Magnetic ComponentsAvoid Hot Inductors!Measurement for Optimal Cloud DeploymentMatter Adoption: What does it take to deploy Matter devices?YARD Stick OneA Sub-1 GHz Wireless Test ToolLatching RelaysPeculiar Parts, the SeriesPIC O’Clock – In Touch with TimeDesigning an SDR Time Signal ReceiverDue Diligence DirectiveBusiness as Usual Will Not DoStarting Out in Electronics……Voltage AmplificationInfrasound Recorder with the Arduino Pro MiniA Sample Project from Elektor’s “Arduino & Co.” BookCloud-Based Energy MeterWith ESP32 Module and PZEM-004T Voltage/Current SensorA Bare-Metal Programming Guide (Part 2)Accurate Timing, the UART, and DebuggingHexadoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2023_en.png?v=1707314707https://www.elektor.com/products/elektor-september-october-2023-en?variant=47666435457356 out of stock 10.95 0 4.9 6.9 nicht auf Lager 47666435883340 Elektor September/October 2023 (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666435883340-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Raspberry Pi Pico as Spectrum AnalyzerFFTs on a Low-Cost Hardware Basis±40-V Linear Voltage RegulatorAn Alternative Power Supply for the Fortissimo-100 Power Amplifier… and Others!MCU Wireless Communication Made FlexibleEEPROM Opens Networking Prospects for Wireless MCUs€5,000 up for grabs!Join the STM32 Wireless Innovation Design Contest2023: An AI OdysseyGetting Started with ChatGPT’s Code InterpreterLoRa, a Swiss Army Knife (1)The LoRa Protocol and Its AdvantagesAdjustable Current Sink with Integrated Clock GeneratorTest Power Supplies, Voltage Converters and BatteriesTwo New Arduino UNO R4 Boards: Minima and WiFiLogarithmic PotentiometersThey’re Exponential!Motor Driver Breakout BoardA BoB for a 5 A DC Motor Driver with a 3×3 mm SizeFrom Life’s ExperienceHazardous ElectronicsIs Cellular the Lowest-Power Option for IoT?LTE-M and NB-IoT Energy Requirements in LPWAN DeploymentsWireless Communication in IoT Systems – Using Arduino MKR ModulesThe Right Board for Wi-Fi, LoRa, and Many More StandardsAC Losses in Magnetic ComponentsAvoid Hot Inductors!Measurement for Optimal Cloud DeploymentMatter Adoption: What does it take to deploy Matter devices?YARD Stick OneA Sub-1 GHz Wireless Test ToolLatching RelaysPeculiar Parts, the SeriesPIC O’Clock – In Touch with TimeDesigning an SDR Time Signal ReceiverDue Diligence DirectiveBusiness as Usual Will Not DoStarting Out in Electronics……Voltage AmplificationInfrasound Recorder with the Arduino Pro MiniA Sample Project from Elektor’s “Arduino & Co.” BookCloud-Based Energy MeterWith ESP32 Module and PZEM-004T Voltage/Current SensorA Bare-Metal Programming Guide (Part 2)Accurate Timing, the UART, and DebuggingHexadoku https://www.elektor.com/cdn/shop/files/elektor-09-10-2023-pdf_en.png?v=1707314719https://www.elektor.com/products/elektor-september-october-2023-pdf-en?variant=47666435883340 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 46907275477324 Elektor September/Oktober 2022 (NL) Elektor Magazines/Specials Bestsellers > Elektor (Print) > Elektor Products > Magazines NP-0674 electronica fast forward Start- & Scale-Up Awardsde voorbereidingen gaan steeds sneller! Bluetooth Low Energy met ESP32-C3 en ESP32het hoeft niet altijd WiFi te zijn! Bluetooth LE-snifferhack een makerdiary nRF52840 MDK USB-dongle Magische RGB LED-kubushardware ontwerpen rond een RP2040 Auto-aan/uit voor soldeerpasta-compressor Elektor video-productieslivestreams, webinars en cursussen voor engineers en pro-makers Elektrificeer je fietsmet een e-bike ombouwset Alle begin......vermenigvuldigt spanningen Uit het leven gegrepennevenactiviteiten Teensy 4.0 – waarom is dat board zo snel?snelheid is geen hekserij! Simulatie van een audio-eindversterker met TINAeerst uitproberen, dan bouwen Ontwikkel en beheer je eigen LoRaWAN IoT-nodesvoorbeeldhoofdstuk: Dragino LHT65, LDS01 en LDS02 LoRaWAN modules Project 2.0correcties, updates en brieven van lezers 5G – alleen voor mijvolledige controle over 5G-implementaties met een eigen cellulair netwerk Elektor Infographics Tips voor het ontwikkelen van een WiFi-interfacetoepassingen uitrusten met WiFi-interfaces Rijntoren-klok Mk 2 Audio-spectrumanalyzer met dekatronsnieuw leven voor vintage-buisjes Data naar Telegram sturenmet een ESP32 en een paar onderdelen Een Fliege-notchfilter voor audiometingenmeet beter met een notchfilter Veranderende industriële communicatieSingle Pair Ethernet – meer dan zo maar een nieuwe connector Elektronische mannetjes-PUT-terzo werkt de programmeerbare unijunctie-transistor Rond touchscreen voor Raspberry PiHyperPixel 2.1 Round van Pimoroni Remote sensing met detectie van verbindingsverliesmet nRF24L01+ modules Digitale FM-ontvanger met Arduino en TEA5767stem af met een Arduino Nano OLED-interface ombouwen van SPI naar I²C Oost West Lab Besteen hobby gaat niet met pensioen... Tien jaar ethiek in elektronicaTessel Renzenbrink over de digitale samenleving en meer HexadokuThe Original Elektorized Sudok https://www.elektor.com/cdn/shop/files/elektor-09-10-2022_nl.png?v=1689092893https://www.elektor.com/products/elektor-september-oktober-2022-nl?variant=46907275477324 in stock 14.95 73 4.9 6.9 2 - 4 Werktage 46907267580236 Elektor September/Oktober 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Magazines has-digital-downloads,variant-46907267580236-has-digital-downloads electronica fast forward Start- & Scale-Up Awardsde voorbereidingen gaan steeds sneller! Bluetooth Low Energy met ESP32-C3 en ESP32het hoeft niet altijd WiFi te zijn! Bluetooth LE-snifferhack een makerdiary nRF52840 MDK USB-dongle Magische RGB LED-kubushardware ontwerpen rond een RP2040 Auto-aan/uit voor soldeerpasta-compressor Elektor video-productieslivestreams, webinars en cursussen voor engineers en pro-makers Elektrificeer je fietsmet een e-bike ombouwset Alle begin......vermenigvuldigt spanningen Uit het leven gegrepennevenactiviteiten Teensy 4.0 – waarom is dat board zo snel?snelheid is geen hekserij! Simulatie van een audio-eindversterker met TINAeerst uitproberen, dan bouwen Ontwikkel en beheer je eigen LoRaWAN IoT-nodesvoorbeeldhoofdstuk: Dragino LHT65, LDS01 en LDS02 LoRaWAN modules Project 2.0correcties, updates en brieven van lezers 5G – alleen voor mijvolledige controle over 5G-implementaties met een eigen cellulair netwerk Elektor Infographics Tips voor het ontwikkelen van een WiFi-interfacetoepassingen uitrusten met WiFi-interfaces Rijntoren-klok Mk 2 Audio-spectrumanalyzer met dekatronsnieuw leven voor vintage-buisjes Data naar Telegram sturenmet een ESP32 en een paar onderdelen Een Fliege-notchfilter voor audiometingenmeet beter met een notchfilter Veranderende industriële communicatieSingle Pair Ethernet – meer dan zo maar een nieuwe connector Elektronische mannetjes-PUT-terzo werkt de programmeerbare unijunctie-transistor Rond touchscreen voor Raspberry PiHyperPixel 2.1 Round van Pimoroni Remote sensing met detectie van verbindingsverliesmet nRF24L01+ modules Digitale FM-ontvanger met Arduino en TEA5767stem af met een Arduino Nano OLED-interface ombouwen van SPI naar I²C Oost West Lab Besteen hobby gaat niet met pensioen... Tien jaar ethiek in elektronicaTessel Renzenbrink over de digitale samenleving en meer HexadokuThe Original Elektorized Sudok https://www.elektor.com/cdn/shop/files/elektor-09-10-2022-pdf_nl.png?v=1689092687https://www.elektor.com/products/elektor-september-oktober-2022-pdf-nl?variant=46907267580236 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47666438570316 Elektor Special: Arduino Guest Edition 2022 PDF (EN) Elektor Digital bundels Bestsellers > Elektor (Digital) > Special Editions has-digital-downloads,variant-47666438570316-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Arduino Portenta Machine Control and Arduino Portenta H7A CAN-to-MQTT Gateway Demo ProjectUnboxing the Elektor LCR Meter with David CuartiellesMicroPython Enters the World of ArduinoConnected Projects, SimplifiedDive Into the Arduino CloudIntroduction to TinyMLBig Is Not Always BetterArduino K-WayWriting Arduino Sketches Just Got BetterGet to Know ArduinoGetting Started with the Portenta X8Manage Software Securely with ContainersBuild, Deploy, and Maintain Scalable, Secure ApplicationsWith Arduino Portenta X8 Featuring NXP’s i.MX 8M Mini Applications Processor and EdgeLock SE050 Secure ElementHow I Automated My HomeArduino CEO Fabio Violante Shares SolutionsAltair 8800 SimulatorHardware Simulation of a Vintage ComputerMS-DOS on the Portenta H7Run Old-School Software on Contemporary HardwareGrow It YourselfA Digitally Controlled, Single-Box Solution for Indoor FarmingSave the Planet With Home Automation?MQTT on the Arduino Nano RP2040 ConnectGo Professional with Arduino ProSmart Ovens Take a Leap Into the FutureTagvance Builds Safer Construction Sites with ArduinoSantagostino Breathes Easywith Remote Monitoring that Leverages AI for Predictive MaintenanceSecurity Flies High with RIoT Secure’s MKR-Based SolutionOpen-Source Brings a New Generation of Water Management to the WorldSensoDetect Deforestation with Sound AnalysisThe Mozzi Arduino Library for Sound SynthesisInsights from Tim BarrassThe New Portenta X8 (with Linux!) and Max Carrier Redefine What’s PossibleHow Using Arduino Helps Students Build Future SkillsMust-Haves for Your Electronics WorkspaceThe Importance of Robotics in EducationDependable IoT Based Upon LoRaUnboxing the Portenta Machine Control8-Bit Gaming with ArduboyReducing Water Usage at Horseback Riding TracksAn IoT to Constantly Monitor Soil Humidity and Temperature LevelsThe Panettone ProjectA sourdough starter management and maintenance systemSupporting Arduino ResellersSpace Invaders with ArduinoArt with ArduinoInspiring Insights from Artists and DesignersArduino Product CatalogueThe Future of Arduino https://www.elektor.com/cdn/shop/files/elektor-special-arduino-guest-edition-2022-pdf_en.png?v=1707314744https://www.elektor.com/products/elektor-special-arduino-guest-edition-2022-pdf-en?variant=47666438570316 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 1.0 kg 46907267940684 Elektor Special: Arduino Guest Edition 2022 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46907267940684-has-digital-downloads Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Arduino Portenta Machine Control en Arduino Portenta H7CAN/MQTT-gateway: een demoprojectUitgepakt: Elektor’s LCR Meter Kitmet David Cuartielles, mede-oprichter van Arduino!MicroPython betreedt de wereld van ArduinoConnected, maar niet complexneem een duik in de Arduino CloudKennismaking met TinyMLgroot is niet altijd beterArduino K-Way:bewust luchtigArduino-sketches schrijven is nog beter gewordenMaak kennis met ArduinoAan de slag met de Portenta X8software veilig beheren met containersBouw, uitrol en onderhoud van schaalbare, veilige applicatiesop basis van Arduino Portenta X8 – met de i.MX 8M Mini Applications Processor en EdgeLock SE050 Secure Element van NXPHoe ik mijn huis automatiseerdeFabio Violante (CEO Arduino) over zijn oplossingenAltair 8800-simulatorhardwaresimulatie van een vintage computerMS-DOS op de Portenta H7antieke software op moderne hardwareLandbouw in zakformaatdigitaal gestuurde kweekbox voor binnenshuisMet Home Automation de wereld redden?MQTT op de Arduino Nano RP2040 ConnectArduino Pro voor professionalsSlimme ovens – de ovens van de toekomstTagvance maakt bouwlocaties veiliger met ArduinoSantagostino krijgt genoeg luchtmet bewaking op afstand en gebruik van AI bij voorspellend onderhoudBeveiliging neemt een hoge vlucht met RIoT Secure’s MKR-gebaseerde oplossingOpen-Source brengt de wereld een nieuwe generatie watermanagementSensoontbossing detecteren met geluidsanalyseDe Mozzi Arduino-library voor geluidssynthesegedachten van Tim BarrassDe nieuwe Portenta X8 (met Linux!) en Max Carrier herdefiniëren het haalbareHoe de Arduino studenten aan vaardigheden voor de toekomst helptMust-haves voor je elektronica-werkplekHet belang van robotica in het onderwijsBetrouwbaar IoT op basis van LoRaAan de slag met de Portenta Machine Control8bit-gaming met ArduboySpaar water op de paardenrenbaanmeet continu de bodemvochtigheid en temperatuurniveau via IoTHet panettone-projectzuurdesemstarter onder controleMet steun van deze Arduino-resellersSpace Invaders met ArduinoKunst met Arduinoinspirerende inzichten van kunstenaars en ontwerpersAan de slag met nieuwe Arduino-hardware!De toekomst van Arduino https://www.elektor.com/cdn/shop/files/elektor-special-arduino-guest-edition-2022-pdf_nl.png?v=1689092701https://www.elektor.com/products/elektor-special-arduino-guest-edition-2022-pdf-nl?variant=46907267940684 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 46907227832652 Elektor Special: Arduino Shields Elektor Magazines/Specials Arduino > Arduino Books > Arduino Shields > Bestsellers > Elektor Products > Magazines > Special Editions 9783895765070 Make your project dreams come true: an odometer for the hamster wheel, a fully automatic control of your ant farm with web interface, or the Sandwich-O-Mat – a machine that toasts and grills sandwiches of your choice. With the Arduino and the DIY or Maker movement, not only did entry into microcontroller programming become child's play, but a second development also took place: Resourceful developers brought small boards – so-called shields or modules – to the market, which greatly simplified the use of additional hardware. The small modules contain all the important electronic parts to be connected to the microcontroller with a few plug-in cables, eliminating the need for a fiddly and time-consuming assembly on the plug-in board. In addition, it is also possible to handle tiny components that do not have any connecting legs (so-called SMDs). Projects Discussed Arduino seeks connection BMP and introduction to libraries, I²C Learn I/O basics with the multi-purpose shield I²C LCD adapter and DOT matrix displays LCD keypad shield Level converter W5100: Internet connection I/O expansion shield Relays and solid-state relays The multi-function shield: A universal control unit Connecting an SD card reader via SPI Keys and 7-segment displays 16-bit ADC MCP4725 DAC 16-way PWM servo driver MP3 player GPS data logger using an SD card Touch sensor Joystick SHT31: Temperature and humidity VEML6070 UV-A sensor VL53L0X time-of-flight Ultrasonic distance meter MAX7219-based LED DOT matrix display DS3231 RTC Port expander MCP23017 433 MHz radio MPU-650 gyroscope ADXL345 accelerometer WS2812 RGB LEDs Power supply MQ-xx gas sensors CO2 gas sensor ACS712 current sensor INA219 current sensor L298 motor driver MFRC522 RFID 28BYJ-48 stepper motor TMC2209 silent step stick X9C10x digital potentiometer ST7735 in a color TFT display e-Paper display Bluetooth Geiger counter SIM800L GSM module I²C multiplexer Controller Area Network https://www.elektor.com/cdn/shop/files/elektor-special-arduino-shields_en.png?v=1689091098https://www.elektor.com/products/elektor-special-arduino-shields-en?variant=46907227832652 in stock 14.95 93 4.9 6.9 2 - 4 Werktage 46907227865420 Elektor Special: Arduino Shields (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46907227865420-has-digital-downloads 978-3-89576-508-7 Make your project dreams come true: an odometer for the hamster wheel, a fully automatic control of your ant farm with web interface, or the Sandwich-O-Mat – a machine that toasts and grills sandwiches of your choice. With the Arduino and the DIY or Maker movement, not only did entry into microcontroller programming become child's play, but a second development also took place: Resourceful developers brought small boards – so-called shields or modules – to the market, which greatly simplified the use of additional hardware. The small modules contain all the important electronic parts to be connected to the microcontroller with a few plug-in cables, eliminating the need for a fiddly and time-consuming assembly on the plug-in board. In addition, it is also possible to handle tiny components that do not have any connecting legs (so-called SMDs). Projects Discussed Arduino seeks connection BMP and introduction to libraries, I²C Learn I/O basics with the multi-purpose shield I²C LCD adapter and DOT matrix displays LCD keypad shield Level converter W5100: Internet connection I/O expansion shield Relays and solid-state relays The multi-function shield: A universal control unit Connecting an SD card reader via SPI Keys and 7-segment displays 16-bit ADC MCP4725 DAC 16-way PWM servo driver MP3 player GPS data logger using an SD card Touch sensor Joystick SHT31: Temperature and humidity VEML6070 UV-A sensor VL53L0X time-of-flight Ultrasonic distance meter MAX7219-based LED DOT matrix display DS3231 RTC Port expander MCP23017 433 MHz radio MPU-650 gyroscope ADXL345 accelerometer WS2812 RGB LEDs Power supply MQ-xx gas sensors CO2 gas sensor ACS712 current sensor INA219 current sensor L298 motor driver MFRC522 RFID 28BYJ-48 stepper motor TMC2209 silent step stick X9C10x digital potentiometer ST7735 in a color TFT display e-Paper display Bluetooth Geiger counter SIM800L GSM module I²C multiplexer Controller Area Network https://www.elektor.com/cdn/shop/files/elektor-special-arduino-shields-pdf_en.png?v=1689091105https://www.elektor.com/products/elektor-special-arduino-shields-pdf-en?variant=46907227865420 in stock 11.95 0 4.9 6.9 2 - 4 Werktage 46864032727372 Elektor Special: Audio 2 PDF (NL) Elektor Digital bundels Bestsellers > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46864032727372-has-digital-downloads Zelfbouw versterkers en luidsprekersDeze speciale uitgave staat vol met interessante bouwbeschrijvingen en achtergrondartikelen van internationaal gerenommeerde ontwerpers. Het gaat in alle gevallen om nieuwe, nog niet eerder gepubliceerde artikelen.InhoudsopgaveBuizenversterkers30 Watt buizenversterker met variabele dempingsfactor50 Watt super triode versterker300 Watt buizen eindversterkerDigibias: digitaal de ruststroom instellen en bewakenLuidsprekersPaper Hatt - klein maar fijnOrigami M en C – compacte actieve subwoofer in twee smakenMeerweg open baffle systemen – basistheorie, ontwerp en meetmethodeMoai – hightech uit ScandinaviëOB3W – drieweg open-baffle dipool van formaat1685a – compacte tweeweg vloerstaanderScanSpeak Vertigo – duizelingwekkend mooi driewegsysteemHalfgeleiderversterkersMinimA – minimalistische 120W klasse-B versterkerGebalanceerde voorversterker met actief wisselfilterRelaiXed – gebalanceerde voorversterker met relais https://www.elektor.com/cdn/shop/products/elektor-special-audio-2-nl.png?v=1688040948https://www.elektor.com/products/elektor-special-audio-2-pdf-nl?variant=46864032727372 in stock 15.9 0 4.9 6.9 2 - 4 Werktage 46864032858444 Elektor Special: Audio 5 PDF (NL) Elektor Digital bundels Bestsellers > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46864032858444-has-digital-downloads Zelfbouw versterkers en luidsprekersOok deze vijfde Audio Special staat weer vol met interessante bouwbeschrijvingen en achtergrondartikelen van internationaal gerenommeerde ontwerpers. Ook dit jaar weer de inmiddels bekende mix van buizenversterkers en luidsprekers, zodat er voor iedere zelfbouwer ongetwijfeld iets interessants te lezen of te bouwen valt. Het gaat in alle gevallen om nieuwe, nog niet eerder gepubliceerde artikelen.InhoudVersterkersClassic Three voorversterkerLijnvoorversterker met 6C33De Dirigent – buizenvoorversterker met actief scheidingsfilterSingle ended KR300B stereo eindversterker1 Watt gitaarversterker – voor huiskamerSingle ended 211 triode versterker – met interstage trafoDieper kijken in de uitgangstransformatorPrelude voorversterker – minimalisme in optima formaKlik aan, klik uit schakelaar – een netschakelaar met legio toepassingenLuidsprekersScheidingsfilters voor luidsprekerboxen – meer valkuilen dan je lief isMorel Elite 420 – actieve tweeweg boekenplank luidsprekerAll back – een verrassend veelzijdige compacte TLHATT-SE MkII Micro Monitor – kleine luidspreker met pitSilverado – een d’Appolito met pitNebular Monitor – een compacte luidspreker met een groots geluidLBVS – zelfbouwklassieker van eigen bodemSolo 201 – er is maar één weg! https://www.elektor.com/cdn/shop/products/elektor-special-audio-5-nl.png?v=1688040953https://www.elektor.com/products/elektor-special-audio-5-pdf-nl?variant=46864032858444 in stock 17.5 0 4.9 6.9 2 - 4 Werktage 47666440995148 Elektor Special: Espressif Guest Edition (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Special Editions has-digital-downloads,variant-47666440995148-has-digital-downloads - Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Accelerating IoT InnovationA Color E-Ink Wi-Fi Picture FrameESP-Launchpad TutorialFrom Zero to Flashing in MinutesESP32 and ChatGPTOn the Way to a Self-Programming System…Walkie-Talkie with ESP-NOWNot Quite Wi-Fi, Not Quite Bluetooth!From Idea to Circuit with the ESP32-S3A Guide to Prototyping with Espressif ChipsAIoT Chip InnovationAn Interview With Espressif CEO Teo Swee-AnnSimulate ESP32 with WokwiYour Project’s Virtual TwinTrying Out the ESP32-S3-BOX-3A Comprehensive AIoT Development PlatformElectronics Workspace EssentialsInsights and Tips From Espressif EngineersThe ESP RainMaker StoryHow We Built “Your” IoT CloudAssembling the Elektor Cloc 2.0 KitAn Elektor Product Unboxed by EspressifUnleashing the ESP32-P4The Next Era of MicrocontrollersRust + EmbeddedA Development Power DuoWho Are the Rust-Dacious Embedded Developers?How Espressif is Cultivating Embedded Rust for the ESP32Espressif’s Series of SoCsBuilding a PLC with Espressif SolutionsWith the Capabilities and Functionality of the ISOBUS ProtocolThe ESP32-S3 VGA BoardBitluni’s Exciting Journey Into Product DesignAcoustic Fingerprinting on ESP32Song Recognition With Open-Source Project OlafCircular Christmas Tree 2023A High-Tech Way to Celebrate the Holiday SeasonA Simpler and More Convenient LifeAn Amateur Project Based on the Espressif ESP8266 ModuleHow to Build IoT Apps without Software ExpertiseWith Blynk IoT Platform and Espressif HardwareBuilding a Smart User Interface on ESP32Quick & Easy IoT Development with M5StackPrototyping an ESP32-Based Energy MeterA Value-Added Distributor for IoT and MoreIn-Depth Insights: Interview With Arduino on the Nano ESP32Alessandro Ranellucci and Martino Facchin Discuss Espressif CollaborationYour AIoT Solution ProviderInsights From EspressifStreamlining MCU Development With ESP-IDF Privilege SeparationAn Open-Source Speech Recognition Server……and the ESP BOXThe Thinking EyeFacial Recognition and More Using the ESP32-S3-EYEESP32-C2-Based Coin Cell SwitchDesign and Performance EvaluationThe Smart Home Leaps Forward with MatterUnlocking Smart Home IoT PotentialTech the Future: Where Is Smart Home IoT Headed? https://www.elektor.com/cdn/shop/files/elektor-special-espressif-guest-edition-2023-pdf_en.png?v=1707314767https://www.elektor.com/products/elektor-special-espressif-guest-edition-2023-pdf-en?variant=47666440995148 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 47666440012108 Elektor Special: Espressif Guest Edition 2023 Elektor Magazines/Specials Bestsellers > Elektor (Print) > Special Editions EP-0526 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Accelerating IoT InnovationA Color E-Ink Wi-Fi Picture FrameESP-Launchpad TutorialFrom Zero to Flashing in MinutesESP32 and ChatGPTOn the Way to a Self-Programming System…Walkie-Talkie with ESP-NOWNot Quite Wi-Fi, Not Quite Bluetooth!From Idea to Circuit with the ESP32-S3A Guide to Prototyping with Espressif ChipsAIoT Chip InnovationAn Interview With Espressif CEO Teo Swee-AnnSimulate ESP32 with WokwiYour Project’s Virtual TwinTrying Out the ESP32-S3-BOX-3A Comprehensive AIoT Development PlatformElectronics Workspace EssentialsInsights and Tips From Espressif EngineersThe ESP RainMaker StoryHow We Built “Your” IoT CloudAssembling the Elektor Cloc 2.0 KitAn Elektor Product Unboxed by EspressifUnleashing the ESP32-P4The Next Era of MicrocontrollersRust + EmbeddedA Development Power DuoWho Are the Rust-Dacious Embedded Developers?How Espressif is Cultivating Embedded Rust for the ESP32Espressif’s Series of SoCsBuilding a PLC with Espressif SolutionsWith the Capabilities and Functionality of the ISOBUS ProtocolThe ESP32-S3 VGA BoardBitluni’s Exciting Journey Into Product DesignAcoustic Fingerprinting on ESP32Song Recognition With Open-Source Project OlafCircular Christmas Tree 2023A High-Tech Way to Celebrate the Holiday SeasonA Simpler and More Convenient LifeAn Amateur Project Based on the Espressif ESP8266 ModuleHow to Build IoT Apps without Software ExpertiseWith Blynk IoT Platform and Espressif HardwareBuilding a Smart User Interface on ESP32Quick & Easy IoT Development with M5StackPrototyping an ESP32-Based Energy MeterA Value-Added Distributor for IoT and MoreIn-Depth Insights: Interview With Arduino on the Nano ESP32Alessandro Ranellucci and Martino Facchin Discuss Espressif CollaborationYour AIoT Solution ProviderInsights From EspressifStreamlining MCU Development With ESP-IDF Privilege SeparationAn Open-Source Speech Recognition Server……and the ESP BOXThe Thinking EyeFacial Recognition and More Using the ESP32-S3-EYEESP32-C2-Based Coin Cell SwitchDesign and Performance EvaluationThe Smart Home Leaps Forward with MatterUnlocking Smart Home IoT PotentialTech the Future: Where Is Smart Home IoT Headed? https://www.elektor.com/cdn/shop/files/elektor-special-espressif-guest-edition-2023_en.png?v=1707314756https://www.elektor.com/products/elektor-special-espressif-guest-edition-2023-en?variant=47666440012108 in stock 10.95 57 4.9 6.9 2 - 4 Werktage 47397002379596 Elektor Special: Espressif Guest Edition 2023 PDF (NL) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Special Editions Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.IoT-innovatie in galopEen E-Ink WiFi kleuren-fotolijstESP-Launchpad tutorialvan nul tot flashen in een paar minutenESP32 en ChatGPTop weg naar een zelf-programmerend systeem…Walkie-talkie met ESP-NOWniet echt WiFi, niet echt Bluetooth, maar...Van idee tot schakeling met de ESP32-S3zo bouw je een prototype met Espressif-chipsAIoT chip-innovatieeen vraaggesprek met Teo Swee-Ann, CEO van EspressifSimuleer ESP32 met Wokwide digitale tweeling van je projectTest van de ESP32-S3-BOX-3een uitgebreid AIoT-ontwikkelplatformvoor je elektronica-werkplekoverwegingen en tips van Espressif-techniciHet ESP RainMaker-verhaalhoe we “jouw” IoT-cloud bouwdenBouw van de Elektor Cloc 2.0een Elektor-product uitgepakt door EspressifDe ESP32-P4 ontketendde volgende microcontroller-eraRust + embeddedeen krachtig ontwikkelduoWie zijn de onvervaarde embedded Rust-ontwikkelaars?zo cultiveert Espressif embedded Rust voor de ESP32de SoC-serie van EspressifEen PLC met oplossingen van Espressifmet de mogelijkheden en functionaliteit van het ISOBUS-protocolHet ESP32-S3 VGA-boardvolg Bitluni tijdens het ontwerpprocesAcoustic fingerprinting met de ESP32songherkenning met het open-source project OlafRonde kerstboom 2023een high-tech manier om de feestdagen te vierenEen eenvoudiger en handiger leveneen amateurproject op basis van de ESP8266-module van EspressifIoT-apps bouwen zonder software-expertisemet het Blynk IoT-platform en Espressif-hardwareBouw een slimme gebruikersinterface op ESP32Snelle en gemakkelijke IoT-ontwikkeling met M5StackPrototype van een ESP32-gebaseerde energiemeterEen distributeur met meerwaarde voor IoT en meerAchter de schermen: vraaggesprek met Arduino over de Nano ESP32Alessandro Ranellucci en Martino Facchin over de samenwerking met Espressifachter de schermen van EspressifStroomlijnen van MCU-ontwikkeling met ESP-IDF Privilege SeparationEen open-source spraakherkenningsserver......en de ESP BOXHet denkende ooggezichtsherkenning en meer met de ESP32-S3-EYEKnoopcel-schakelaar met ESP32-C2prestatiegericht ontwerpenMatter stuwt het slimme huis voorwaartsontsluit het potentieel van Smart Home IoTTech the Future: Waarheen met Smarthome IoT? https://www.elektor.com/cdn/shop/files/elektor-special-espressif-guest-edition-2023-pdf_nl.png?v=1701161094https://www.elektor.com/products/elektor-special-espressif-guest-edition-2023-pdf-nl?variant=47397002379596 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47666437292364 Elektor Special: Guest-edited by Arduino Elektor Magazines/Specials Bestsellers > Elektor (Print) > Special Editions EP-0518 Elektor GREEN and GOLD members can download their digital edition here.Not a member yet? Click here.Arduino Portenta Machine Control and Arduino Portenta H7A CAN-to-MQTT Gateway Demo ProjectUnboxing the Elektor LCR Meter with David CuartiellesMicroPython Enters the World of ArduinoConnected Projects, SimplifiedDive Into the Arduino CloudIntroduction to TinyMLBig Is Not Always BetterArduino K-WayWriting Arduino Sketches Just Got BetterGet to Know ArduinoGetting Started with the Portenta X8Manage Software Securely with ContainersBuild, Deploy, and Maintain Scalable, Secure ApplicationsWith Arduino Portenta X8 Featuring NXP’s i.MX 8M Mini Applications Processor and EdgeLock SE050 Secure ElementHow I Automated My HomeArduino CEO Fabio Violante Shares SolutionsAltair 8800 SimulatorHardware Simulation of a Vintage ComputerMS-DOS on the Portenta H7Run Old-School Software on Contemporary HardwareGrow It YourselfA Digitally Controlled, Single-Box Solution for Indoor FarmingSave the Planet With Home Automation?MQTT on the Arduino Nano RP2040 ConnectGo Professional with Arduino ProSmart Ovens Take a Leap Into the FutureTagvance Builds Safer Construction Sites with ArduinoSantagostino Breathes Easywith Remote Monitoring that Leverages AI for Predictive MaintenanceSecurity Flies High with RIoT Secure’s MKR-Based SolutionOpen-Source Brings a New Generation of Water Management to the WorldSensoDetect Deforestation with Sound AnalysisThe Mozzi Arduino Library for Sound SynthesisInsights from Tim BarrassThe New Portenta X8 (with Linux!) and Max Carrier Redefine What’s PossibleHow Using Arduino Helps Students Build Future SkillsMust-Haves for Your Electronics WorkspaceThe Importance of Robotics in EducationDependable IoT Based Upon LoRaUnboxing the Portenta Machine Control8-Bit Gaming with ArduboyReducing Water Usage at Horseback Riding TracksAn IoT to Constantly Monitor Soil Humidity and Temperature LevelsThe Panettone ProjectA sourdough starter management and maintenance systemSupporting Arduino ResellersSpace Invaders with ArduinoArt with ArduinoInspiring Insights from Artists and DesignersArduino Product CatalogueThe Future of Arduino https://www.elektor.com/cdn/shop/files/elektor-special-arduino-guest-edition-2022_en_1.png?v=1707314732https://www.elektor.com/products/elektor-special-arduino-guest-edition-2022-en?variant=47666437292364 in stock 10.95 39 4.9 6.9 2 - 4 Werktage 46907115241804 Elektor Special: Introduction to Electronics with Arduino Elektor Magazines/Specials Arduino > Bestsellers > Elektor Products > Magazines > Special Editions 9783895764028 Although the Arduino isn’t a novelty any longer, there are still many beginners who want to try programming and development with a microcontroller, and to them, it is all new. All beginnings can be difficult, though they should be light and enjoyable. You do not need much or expensive equipment for the examples. The circuits are built on a small breadboard, and, if necessary, connected to an Arduino Uno, which you can program on a Windows PC. You will find clear examples of how to build all circuits, ensuring easy and error-free reproduction. Projects Discussed Current & Voltage – How it all began Arduino Hardware Arduino Programming The Electrical Circuit Measuring with the Multimeter Circuit Diagrams and Breadboards Creating Circuit Diagrams Breadboard Views with Fritzing Online Circuit Simulation Indispensable: Resistors (Part 1) Hands-on with Resistors (Part 2) Variable Resistors Diodes: One-way Street for Current The Transistor Switch Electromagnetism Relays and Motors op-amps: Operational Amplifiers Capacitors The NE555 Timer PWM and Analogue Values with Arduino 7-Segment Temperature Display Introduction to Soldering and LCDs https://www.elektor.com/cdn/shop/files/elektor-special_introduction-to-electronics-with-arduino.png?v=1689087535https://www.elektor.com/products/elektor-special-introduction-to-electronics-with-arduino?variant=46907115241804 in stock 14.95 35 4.9 6.9 2 - 4 Werktage 46907115372876 Elektor Special: Introduction to Electronics with Arduino (PDF) Elektor Digital bundels Bestsellers > Magazines > Special Editions has-digital-downloads,variant-46907115372876-has-digital-downloads Although the Arduino isn’t a novelty any longer, there are still many beginners who want to try programming and development with a microcontroller, and to them, it is all new. All beginnings can be difficult, though they should be light and enjoyable. You do not need much or expensive equipment for the examples. The circuits are built on a small breadboard, and, if necessary, connected to an Arduino Uno, which you can program on a Windows PC. You will find clear examples of how to build all circuits, ensuring easy and error-free reproduction. Projects Discussed Current & Voltage – How it all began Arduino Hardware Arduino Programming The Electrical Circuit Measuring with the Multimeter Circuit Diagrams and Breadboards Creating Circuit Diagrams Breadboard Views with Fritzing Online Circuit Simulation Indispensable: Resistors (Part 1) Hands-on with Resistors (Part 2) Variable Resistors Diodes: One-way Street for Current The Transistor Switch Electromagnetism Relays and Motors op-amps: Operational Amplifiers Capacitors The NE555 Timer PWM and Analogue Values with Arduino 7-Segment Temperature Display Introduction to Soldering and LCDs https://www.elektor.com/cdn/shop/files/elektor-special_introduction-to-electronics-with-arduino-pdf.png?v=1689087542https://www.elektor.com/products/elektor-special-introduction-to-electronics-with-arduino-pdf?variant=46907115372876 in stock 11.95 0 4.9 6.9 2 - 4 Werktage 46864032235852 Elektor Special: LED's 1 PDF (NL) Elektor Digital bundels Bestsellers > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46864032235852-has-digital-downloads Lichtgevende dioden in theorie en praktijkDoor verbetering van de lichtopbrengst en goedkopere productiemethoden is het toepassingsgebied van de LED uitgebreid van optische indicator tot energiezuinige lichtbron. Deze speciale Elektor-uitgave biedt niet alleen theoretische informatie, maar laat ook zien hoe en waar LED’s tegenwoordig toegepast worden. Bovendien bevat deze uitgave enkele beproefde elektronische schakelingen voor zelfbouw, zodat elke (aspirant)elektronicus zelf met LED’s aan de slag kan gaan.Een greep uit de inhoudTheorie & ToepassingenAansturing en koeling van LED-lampenDe technologie achter LED-projectorenConstante-stroom-omzetters voor power-LED’sLED-stuur- en vermogenselektronica op één chipZelfbouwprojectenAmbilight met BluetoothArtistieke LED-dimmerMicrocontrollergestuurde LED-kerstboomVrij programmeerbare LED-lamp https://www.elektor.com/cdn/shop/products/elektor-special-leds-1-nl.png?v=1688040936https://www.elektor.com/products/elektor-special-led-s-1-pdf-nl?variant=46864032235852 in stock 17.5 0 4.9 6.9 2 - 4 Werktage 46864032432460 Elektor Special: LED's 2 PDF (NL) Elektor Digital bundels Bestsellers > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46864032432460-has-digital-downloads Lichtgevende dioden in theorie en praktijkDoor verbetering van de lichtopbrengst en goedkopere productiemethoden is het toepassingsgebied van de LED uitgebreid van optische indicator tot energiezuinige lichtbron. Deze tweede Elektor LED Special biedt niet alleen theoretische informatie, maar laat ook zien hoe en waar LED’s tegenwoordig toegepast worden. Bovendien bevat deze uitgave enkele beproefde elektronische schakelingen voor zelfbouw, zodat elke (aspirant)elektronicus zelf met LED’s aan de slag kan gaan.Een greep uit de inhoudTheorie & ToepassingenUV-vermogenslichtbron met lichtgevende diodenWaterzuivering met UV-LED’sCool Down: koeling van LED’s in de praktijkAansturing van hoogvermogen-LED-verlichtingssystemenOmbouw: referentie-ontwerp voor hanglampenMulticolour-driver voor vermogens-LED’sZelfbouwprojectenOptische meettechnieken voor lichtgevende diodenVallende ster: een meteoor van LED’sLED-interface met 64 uitgangen https://www.elektor.com/cdn/shop/products/elektor-special-leds-2-nl.png?v=1688040942https://www.elektor.com/products/elektor-special-led-s-2-pdf-nl?variant=46864032432460 in stock 17.5 0 4.9 6.9 2 - 4 Werktage 46907262370124 Elektor Special: Power Supplies and Batteries Elektor Magazines/Specials Bestsellers > Elektor Products > Magazines > NEW > Special Editions 9783895765551 Whatever the methods or even then financial means you have to make your circuits work, the power supply should rank high if not Number One in your considerations. The design block simply called “power supply” is hugely underrated both in electronics creation and repair. Yet, the “PSU” has enormous diversity and comes in wildly differing guises like AC/DC, generator, battery (rechargeable or not), PV panel, benchtop, linear or switch-mode, to mention but a few. The output ranges are also staggering like nano-amps to kiloamps and the same for voltages.This special covers the features and design aspects of power supplies.ContentsBasicsBattery ManagementWhat to be aware of when using (Lithium) batteries.Fixed-Voltage Power Supply using Linear RegulatorsThe best result right after batteries.Light Energy HarvestingA small solar panel is used in an energy harvesting project to manage and charge four AAA cells.Mains Powered Adapter DesignBasic circuits and tips for transformers, rectification, filtering and stabilization.LM317 Soft StartThe high inrush current pulse should be avoided.Controllable RectifiersSome suggestions to keep the power loss in the linear regulator as low as possible.ComponentsWorksheet: The LM117 / LM217 / LM317 Voltage RegulatorsSupercapsLow voltage but lots of current… or not?ReviewsJOY-iT RD6006 Benchtop Power Supply KitSiglent SDL1020X Programmable DC Electronic LoadProjectsBalcony Power PlantDIY solar balcony = speedy payback!DIY LiPo Supercharger KitFrom handcrafted to mass marketDual-Anode MOSFET ThyristorFaster and less wasteful than the old SCRBattery JuicerDo not throw away, squeeze!High-Voltage Power Supply with Curve TracerGenerate voltages up to 400 V and trace characteristics curves for valves and transistorsHigh Voltage Supply for RIAAFor RIAA tube preamps and other applications.MicroSupplyA lab power supply for connected devicesPhantom Power Supply using Switched CapacitorsVoltage tripler using three ICsThe SMPS800RE Switch-Mode Supply for the Elektor Fortissimo-100Reliable, light and affordableSoft Start for PSUBe nice to your power supply – and its loadUniLab 20-30 V, 3 A compact switch-mode lab power supplyTipsSoft Start for Step-Down Switching RegulatorsLow Loss Current LimitPowerbank SurpriseA Virtual GroundBattery MaintainerBattery Pack DischargerConnecting Voltage Regulators in Parallel https://www.elektor.com/cdn/shop/files/elektor-special-power-supplies-and-batteries.png?v=1689092495https://www.elektor.com/products/elektor-special-power-supplies-and-batteries?variant=46907262370124 in stock 14.95 134 4.9 6.9 2 - 4 Werktage 46907262468428 Elektor Special: Power Supplies and Batteries (PDF) Elektor Digital bundels Bestsellers > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46907262468428-has-digital-downloads Whatever the methods or even then financial means you have to make your circuits work, the power supply should rank high if not Number One in your considerations. The design block simply called “power supply” is hugely underrated both in electronics creation and repair. Yet, the “PSU” has enormous diversity and comes in wildly differing guises like AC/DC, generator, battery (rechargeable or not), PV panel, benchtop, linear or switch-mode, to mention but a few. The output ranges are also staggering like nano-amps to kiloamps and the same for voltages.This special covers the features and design aspects of power supplies.ContentsBasicsBattery ManagementWhat to be aware of when using (Lithium) batteries.Fixed-Voltage Power Supply using Linear RegulatorsThe best result right after batteries.Light Energy HarvestingA small solar panel is used in an energy harvesting project to manage and charge four AAA cells.Mains Powered Adapter DesignBasic circuits and tips for transformers, rectification, filtering and stabilization.LM317 Soft StartThe high inrush current pulse should be avoided.Controllable RectifiersSome suggestions to keep the power loss in the linear regulator as low as possible.ComponentsWorksheet: The LM117 / LM217 / LM317 Voltage RegulatorsSupercapsLow voltage but lots of current… or not?ReviewsJOY-iT RD6006 Benchtop Power Supply KitSiglent SDL1020X Programmable DC Electronic LoadProjectsBalcony Power PlantDIY solar balcony = speedy payback!DIY LiPo Supercharger KitFrom handcrafted to mass marketDual-Anode MOSFET ThyristorFaster and less wasteful than the old SCRBattery JuicerDo not throw away, squeeze!High-Voltage Power Supply with Curve TracerGenerate voltages up to 400 V and trace characteristics curves for valves and transistorsHigh Voltage Supply for RIAAFor RIAA tube preamps and other applications.MicroSupplyA lab power supply for connected devicesPhantom Power Supply using Switched CapacitorsVoltage tripler using three ICsThe SMPS800RE Switch-Mode Supply for the Elektor Fortissimo-100Reliable, light and affordableSoft Start for PSUBe nice to your power supply – and its loadUniLab 20-30 V, 3 A compact switch-mode lab power supplyTipsSoft Start for Step-Down Switching RegulatorsLow Loss Current LimitPowerbank SurpriseA Virtual GroundBattery MaintainerBattery Pack DischargerConnecting Voltage Regulators in Parallel https://www.elektor.com/cdn/shop/files/elektor-special-power-supplies-and-batteries-pdf.png?v=1689092502https://www.elektor.com/products/elektor-special-power-supplies-and-batteries-pdf?variant=46907262468428 in stock 11.95 0 4.9 6.9 2 - 4 Werktage 46907233927500 Elektor Special: Raspberry Pi and Pico Elektor Magazines/Specials Bestsellers > Elektor Products > Magazines > NEW > Special Editions 9783895765179 Contents Projects PicoVoiceVoice alienation and sound effects with the Raspberry Pi Pico Navigation with Vibration Feedback POV Display Pulse Width Modulation (PWM) with the Raspberry Pi Pico Wi-Fi with the Raspberry Pi Pico 'Hello World' from the Raspberry Pi Pico and RP2040A look at the Raspberry Pi Foundation’s first microcontroller Simple On-Off Temperature Controller with Raspberry Pi HAT Multitasking with the Raspberry PiShowcase: a traffic lights controller The Raspberry Pi Ruler GadgetFun with a time-of-flight sensor Raspberry Pi Buffer Board (Mk. 1)Never blow up the I/O again FM radio with RDSA top HAT project for the Raspberry Pi LoRa with the Raspberry Pi PicoFun with MicroPython! Tutorials Qt for the Raspberry Pi Raspberry Pi Pico Programmingwith MicroPython and Thonny Raspberry Pi Full StackRPi and RF24 at the heart of a sensor network Raspberry Pi Bash Command Cheat Sheet Community Java on the Raspberry PiAn interview with Frank Delporte Reviews Introducing the New Raspberry Pi Pico W, H, and WH Secure Boot Solution for Raspberry PiRetrofit security at a reasonable price Review: SmartPi – Smart Meter Extension for Raspberry Pi Review: The Enviro+ Raspberry Pi HATMeasuring environmental data with Raspberry Pi and the HAT Enviro+ Review: Meet the Raspberry Pi 4All new but still good? Raspberry Pi Gets a Fast 3.5' Touch DisplayMore power at no extra charge Book Launch: Raspberry Pi for Radio Amateurs https://www.elektor.com/cdn/shop/files/elektor-special-raspberry-pi-and-pico.png?v=1689091403https://www.elektor.com/products/elektor-special-raspberry-pi-and-pico?variant=46907233927500 in stock 14.95 118 4.9 6.9 2 - 4 Werktage 46907234091340 Elektor Special: Raspberry Pi and Pico (PDF) Elektor Digital bundels Bestsellers > Elektor (Digital) > Elektor Products > Magazines > Special Editions has-digital-downloads,variant-46907234091340-has-digital-downloads Contents Projects PicoVoiceVoice alienation and sound effects with the Raspberry Pi Pico Navigation with Vibration Feedback POV Display Pulse Width Modulation (PWM) with the Raspberry Pi Pico Wi-Fi with the Raspberry Pi Pico 'Hello World' from the Raspberry Pi Pico and RP2040A look at the Raspberry Pi Foundation’s first microcontroller Simple On-Off Temperature Controller with Raspberry Pi HAT Multitasking with the Raspberry PiShowcase: a traffic lights controller The Raspberry Pi Ruler GadgetFun with a time-of-flight sensor Raspberry Pi Buffer Board (Mk. 1)Never blow up the I/O again FM radio with RDSA top HAT project for the Raspberry Pi LoRa with the Raspberry Pi PicoFun with MicroPython! Tutorials Qt for the Raspberry Pi Raspberry Pi Pico Programmingwith MicroPython and Thonny Raspberry Pi Full StackRPi and RF24 at the heart of a sensor network Raspberry Pi Bash Command Cheat Sheet Community Java on the Raspberry PiAn interview with Frank Delporte Reviews Introducing the New Raspberry Pi Pico W, H, and WH Secure Boot Solution for Raspberry PiRetrofit security at a reasonable price Review: SmartPi – Smart Meter Extension for Raspberry Pi Review: The Enviro+ Raspberry Pi HATMeasuring environmental data with Raspberry Pi and the HAT Enviro+ Review: Meet the Raspberry Pi 4All new but still good? Raspberry Pi Gets a Fast 3.5' Touch DisplayMore power at no extra charge Book Launch: Raspberry Pi for Radio Amateurs https://www.elektor.com/cdn/shop/files/elektor-special-raspberry-pi-and-pico-pdf.png?v=1689091410https://www.elektor.com/products/elektor-special-raspberry-pi-and-pico-pdf?variant=46907234091340 in stock 11.95 0 4.9 6.9 2 - 4 Werktage 47666441617740 Elektor Summer Circuits 2022 Elektor Magazines Bestsellers > Elektor (Print) 020191 Over 50 Circuits & Projects US-Style Siren Two Rotary Encoders on One Analog Input How to Build a Digital 220-V AC Dimmer with Arduino Current Source for LEDs Detect Four Switches with 1 Pin Tiny On/Off Switch with Battery Level Check DIY Hand Sanitizer Dispenser A Simple Electronic Organ Ultra-Simple Stereo Amplifier Sound Activated Switch for Amplifiers Balanced/Unbalanced Converter External Mains Filter Button-Free Door Control DI Box for a Smartphone Fun With Running Lights One-Button Thyristor Control Quasi-Analog Exposure Timer for the Dark Room Circuits Galore From the Hackster.io Community Analog Tanning Timer Yet Another Single-Wire LCD Interface Simple AVR ATtiny13-Based PWM Generator Second Life for Batteries Touch Switch for LED Lights Tester for LEDs and DIP Switches Go/No-Go IR Control Tester Power Semiconductor Tester SPI for WS2812(B) LEDs Measuring Power Inductors One Plug for Raspberry Pi and Audio DAC DIY Test Fixture for the LCR Meter Arduino Ammeter Two-Finger Organ Low Noise ADC Calibrator DC/DC Boost Converter Two Potentiometers on One Digital Input Acoustic Proximity Sensor Battery-Free Radiator Sensor A Circuit for Detecting Bugs and Wireless Cameras Car Interior Light Timer Candle Simulator Digital Kitchen Timer Milliohm Meter Hot Water Production Delay Timer Simple Charger for 2S 18650 Cells Tiny Frequency Reference Low-Power IR Switch Recycle Your Car’s Telephone Charger Microphone Pre-Amp for Arduino DIY EMI Filters Electronic Dice Without an MCU Finger Capacitor A Self-Charging LED Flasher Also in this edition KiCad 6 – Five Features to Consider Flashback – The Elektor SC/MP Computer Interview – Making Art with Electricity My First PCB – Going Head First Into KiCad Minimizing Hardware with Smart Software Infographics – Facts and Figures New Devices from Analog Flashback – The Elektor Metal Detector Hexadoku – The Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-summer-circuits-2022_en.png?v=1707314779https://www.elektor.com/products/elektor-summer-circuits-2022-en?variant=47666441617740 in stock 10.95 71 4.9 6.9 2 - 4 Werktage 46907226784076 Elektor Summer Circuits 2022 (NL) Elektor Magazines Bestsellers > Elektor (Print) > Elektor Products > Magazines > No Member Discount 871096610122302201 Elektor GREEN en GOLD leden kunnen deze uitgave hier downloaden.Nog geen lid? Klik hier om een lidmaatschap af te sluiten.Meer dan 50 schakelingen & projectenUS-sireneTwee draai-encoders op één analoge ingangDigitale 220VAC-dimmer met ArduinoStroombron voor LED’sVier schakelaars detecteren met één pinKleine aan/uit-schakelaar met accucontroleDesinfectie-dispenser voor zelfbouwEenvoudig elektronisch orgelSimpele stereoversterkerAudiogestuurde schakelaarGebalanceerd/ongebalanceerd-converterExtern netfilterKnoploze garagedeurbedieningDI-box voor smartphonePret met een looplichtEenknops-thyristorbesturingQuasi-analoge belichtingstimer voor de donkere kamerSchakelingen bij de Hackster.io-communityAnaloge zonnebad-timerWeer een eendraads LCD-interfaceSimpele PWM-generator met AVR ATtiny13Een tweede leven voor batterijenAanraakschakelaar voor LED-verlichtingTester voor LED’s en DIP-schakelaarsIR-afstandsbedieningstesterTester voor vermogens-halfgeleidersSPI voor WS2812(B)-LED’sMeten van vermogens-zelfinductiesEén stekker voor Raspberry Pi en Audio DACDoe-het-zelf meetklem voor de LCR-meterArduino-ampèremeterTweevinger-orgelRuisarme ADC-kalibratorDC/DC-boostconverterTwee potmeters op één digitale ingangAkoestische nabijheidssensorBatterijloze radiatorsensorSpeurneus voor draadloze camera’s en microfoonsTimer voor auto-binnenverlichtingKaarssimulatorDigitale keukentimerMilliohm-meterWarmwatervertragerEenvoudige lader voor twee (of meer) 18650-cellenMini-frequentiereferentieZuinige IR-schakelaarHergebruik de telefoonlader van je autoMicrofoon-voorversterker voor ArduinoEMI-filters voor zelfbouwElektronische dobbelsteen zonder MCUVingercondensatorZelfladende flits-LEDOok in deze editieKiCad 6 – vijf interessante nieuwe functiesRetrotronica – de Elektor SC/MP-computerInterview – kunst maken met elektriciteitMijn eerste print – spring in het diepe... met KiCadMet slimme software de hardware minimaliserenElektor Infographics – feiten en cijfersNieuwe componenten van AnalogOptimalisering van de signaalintegriteit – Industry 4.0 vereist vlekkeloos werkende interfaces7Hexadoku – puzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-summer-circuits-2022_nl.png?v=1689091019https://www.elektor.com/products/elektor-summer-circuits-2022-nl?variant=46907226784076 in stock 14.95 9.95 137 4.9 6.9 2 - 4 Werktage 47666443714892 Elektor Summer Circuits 2022 (PDF) Elektor Digital Magazines Bestsellers > Elektor (Digital) has-digital-downloads,variant-47666443714892-has-digital-downloads - Over 50 Circuits & Projects US-Style Siren Two Rotary Encoders on One Analog Input How to Build a Digital 220-V AC Dimmer with Arduino Current Source for LEDs Detect Four Switches with 1 Pin Tiny On/Off Switch with Battery Level Check DIY Hand Sanitizer Dispenser A Simple Electronic Organ Ultra-Simple Stereo Amplifier Sound Activated Switch for Amplifiers Balanced/Unbalanced Converter External Mains Filter Button-Free Door Control DI Box for a Smartphone Fun With Running Lights One-Button Thyristor Control Quasi-Analog Exposure Timer for the Dark Room Circuits Galore From the Hackster.io Community Analog Tanning Timer Yet Another Single-Wire LCD Interface Simple AVR ATtiny13-Based PWM Generator Second Life for Batteries Touch Switch for LED Lights Tester for LEDs and DIP Switches Go/No-Go IR Control Tester Power Semiconductor Tester SPI for WS2812(B) LEDs Measuring Power Inductors One Plug for Raspberry Pi and Audio DAC DIY Test Fixture for the LCR Meter Arduino Ammeter Two-Finger Organ Low Noise ADC Calibrator DC/DC Boost Converter Two Potentiometers on One Digital Input Acoustic Proximity Sensor Battery-Free Radiator Sensor A Circuit for Detecting Bugs and Wireless Cameras Car Interior Light Timer Candle Simulator Digital Kitchen Timer Milliohm Meter Hot Water Production Delay Timer Simple Charger for 2S 18650 Cells Tiny Frequency Reference Low-Power IR Switch Recycle Your Car’s Telephone Charger Microphone Pre-Amp for Arduino DIY EMI Filters Electronic Dice Without an MCU Finger Capacitor A Self-Charging LED Flasher Also in this edition KiCad 6 – Five Features to Consider Flashback – The Elektor SC/MP Computer Interview – Making Art with Electricity My First PCB – Going Head First Into KiCad Minimizing Hardware with Smart Software Infographics – Facts and Figures New Devices from Analog Flashback – The Elektor Metal Detector Hexadoku – The Original Elektorized Sudoku https://www.elektor.com/cdn/shop/files/elektor-summer-circuits-2022-pdf_en.png?v=1707314790https://www.elektor.com/products/elektor-summer-circuits-2022-pdf-en?variant=47666443714892 in stock 7.5 0 4.9 6.9 2 - 4 Werktage 46907232125260 Elektor Summer Circuits 2022 PDF (NL) Elektor Digital Magazines Bestsellers > Elektor (Digital) > Magazines has-digital-downloads,variant-46907232125260-has-digital-downloads Meer dan 50 schakelingen & projecten US-sirene Twee draai-encoders op één analoge ingang Digitale 220VAC-dimmer met Arduino Stroombron voor LED’s Vier schakelaars detecteren met één pin Kleine aan/uit-schakelaar met accucontrole Desinfectie-dispenser voor zelfbouw Eenvoudig elektronisch orgel Simpele stereoversterker Audiogestuurde schakelaar Gebalanceerd/ongebalanceerd-converter Extern netfilter Knoploze garagedeurbediening DI-box voor smartphone Pret met een looplicht Eenknops-thyristorbesturing Quasi-analoge belichtingstimer voor de donkere kamer Schakelingen bij de Hackster.io-community Analoge zonnebad-timer Weer een eendraads LCD-interface Simpele PWM-generator met AVR ATtiny13 Een tweede leven voor batterijen Aanraakschakelaar voor LED-verlichting Tester voor LED’s en DIP-schakelaars IR-afstandsbedieningstester Tester voor vermogens-halfgeleiders SPI voor WS2812(B)-LED’s Meten van vermogens-zelfinducties Eén stekker voor Raspberry Pi en Audio DAC Doe-het-zelf meetklem voor de LCR-meter Arduino-ampèremeter Tweevinger-orgel Ruisarme ADC-kalibrator DC/DC-boostconverter Twee potmeters op één digitale ingang Akoestische nabijheidssensor Batterijloze radiatorsensor Speurneus voor draadloze camera’s en microfoons Timer voor auto-binnenverlichting Kaarssimulator Digitale keukentimer Milliohm-meter Warmwatervertrager Eenvoudige lader voor twee (of meer) 18650-cellen Mini-frequentiereferentie Zuinige IR-schakelaar Hergebruik de telefoonlader van je auto Microfoon-voorversterker voor Arduino EMI-filters voor zelfbouw Elektronische dobbelsteen zonder MCU Vingercondensator Zelfladende flits-LED Ook in deze editie KiCad 6 – vijf interessante nieuwe functies Retrotronica – de Elektor SC/MP-computer Interview – kunst maken met elektriciteit Mijn eerste print – spring in het diepe... met KiCad Met slimme software de hardware minimaliseren Elektor Infographics – feiten en cijfers Nieuwe componenten van Analog Optimalisering van de signaalintegriteit – Industry 4.0 vereist vlekkeloos werkende interfaces7 Hexadoku – puzzelen voor elektronici https://www.elektor.com/cdn/shop/files/elektor-summer-circuits-2022-pdf_nl.png?v=1689091277https://www.elektor.com/products/elektor-summer-circuits-2022-pdf-nl?variant=46907232125260 in stock 9.95 0 4.9 6.9 2 - 4 Werktage 47310494728524 Elektor Super Servo Tester kit Elektor Labs Boards&Kits Bestsellers > Elektor Kits > Elektor Products > Motors > NEW 7442105132164 The Elektor Super Servo Tester can control servos and measure servo signals. It can test up to four servo channels at the same time. The Super Servo Tester comes as a kit. All the parts required to assemble the Super Servo Tester are included in the kit. Assembling the kit requires basic soldering skills. The microcontroller is already programmed. The Super Servo Tester features two operating modes: Control/Manual and Measure/Inputs. In Control/Manual mode the Super Servo Tester generates control signals on its outputs for up to four servos or for the flight controller or ESC. The signals are controlled by the four potentiometers. In Measure/Inputs the Super Servo Tester measures the servo signals connected to its inputs. These signals may come from for instance an ESC, a flight controller, or the receiver or another device. The signals are also routed to the outputs to control the servos or the flight controller or ESC. The results are shown on the display. Specifications Operating modes Control/Manual & Measure/Inputs Channels 3 Servo signal inputs 4 Servo signal outputs 4 Alarm Buzzer & LED Display 0.96' OLED (128 x 32 pixels) Input voltage on K5 7-12 VDC Input voltage on K1 5-7.5 VDC Input current 30 mA (9 VDC on K5, nothing connected to K1 and K2) Dimensions 113 x 66 x 25 mm Weight 60 g Included Resistors (0.25 W) R1, R3 1 kΩ, 5% R2, R4, R5, R6, R7, R9, R10 10 kΩ, 5% R8 22 Ω, 5% P1, P2, P3, P4 10 kΩ, lin/B, vertical potentiometer Capacitors C1 100 µF 16 V C2 10 µF 25 V C3, C4, C7 100 nF C5, C6 22 pF Semiconductors D1 1N5817 D2 LM385Z-2.5 D3 BZX79-C5V1 IC1 7805 IC2 ATmega328P-PU, programmed LED1 LED, 3 mm, red T1 2N7000 Miscellaneous BUZ1 Piezo buzzer with oscillator K1, K2 2-row, 12-way pinheader, 90° K5 Barrel jack K4 1-row, 4-way pin socket K3 2-row, 6-way boxed pinheader S1 Slide switch DPDT S2 Slide switch SPDT X1 Crystal, 16 MHz 28-way DIP socket for IC2 Elektor PCB OLED display, 0.96', 128 x 32 pixels, 4-pin I²C interface Links Elektor Magazine Elektor Labs https://www.elektor.com/cdn/shop/files/Elektor-Super-Servo-Tester-Kit.jpg?v=1701860274https://www.elektor.com/cdn/shop/files/Elektor-Super-Servo-Tester-Kit_display.jpg?v=1701860280,https://www.elektor.com/cdn/shop/files/Elektor-Super-Servo-Tester-Kit_car.png?v=1701860285,https://www.elektor.com/cdn/shop/files/Elektor-Super-Servo-Tester-Kit_contents.png?v=1701860293https://www.elektor.com/products/elektor-super-servo-tester-kit?variant=47310494728524 in stock 49.95 42.95 149 4.9 6.9 2 - 4 Werktage 47310494925132 Elektor Tapir E-Smog Detector Kit Elektor Labs Boards&Kits Analyzers > Bestsellers > Elektor Kits > Elektor Products > NEW > No Member Discount > Sale 7442105132157 Ultrasensitive wideband magnetic/electromagnetic field detector This ultra sensitive wideband “E-smog” detector adds two senses to help you track down noise that’s normally inaudible. TAPIR also makes a great project to build since the enclosure is the PCB proper. TAPIR detects electric as well as magnetic fields at high frequencies. The PCB is ingenuously designed to double as a shielded case. Each of the two antennas that can be connected to TAPIR is optimized for one type of field. Magnetic fields are detected with a ferrite-cored coil, and electric fields with a rod antenna, which is easily constructed from a length of stiff wire. Using TAPIR is dead easy. Connect the headphones, the selected antenna and switch on. Move the antenna around any suspect area and you’ll hear different types of noise and noise levels with each electrical device, depending on the type and frequency of the emitted field. Features Ultrasensitive Wideband 'E-smog' Detector PCB Doubles as Project Housing Tried & Tested by Elektor Labs Educational & Geeky Project Easy to solder SMD Parts Online Illustrated Construction Manual Included Printed Circuit Board All Components Antenna and Headphones https://www.elektor.com/cdn/shop/files/Elektor-Tapir-E-Smog-Detector-Kit_box.jpg?v=1700070206https://www.elektor.com/cdn/shop/files/Elektor-Tapir-E-Smog-Detector-Kit.jpg?v=1700070206,https://www.elektor.com/cdn/shop/files/Elektor-Tapir-E-Smog-Detector-Kit_front.jpg?v=1700070206,https://www.elektor.com/cdn/shop/files/Elektor-Tapir