NEW

358 products


  • Last stock! Waveshare PoE Ethernet/USB Hub Box for Raspberry Pi Zero (3x USB 2.0, 802.3af-Compliant)

    Waveshare Waveshare PoE Ethernet/USB Hub Box for Raspberry Pi Zero (3x USB 2.0, 802.3af-Compliant)

    1 in stock

    The PoE-ETH-USB-Hub-Box is a Hub kit with PoE/ETH/USB Hub HAT inside. It is tailored for Raspberry Pi Zero series, small in size, each cut-out of the case is exactly aligned with the connector. The case adopts classic Raspberry Pi red/white color combination, with quality dull polish surface, effectively keeping the Zero away from dust. By using this small Hub Box and some proper 802.3af-compliant power sourcing equipments, it is possible to provide both network connection and power supply for your Raspberry Pi Zero in only one Ethernet cable, along with 3x extended USB ports. Features Designed for Raspberry Pi Zero, compatible with Zero series boards Incorporates RTL8152B Ethernet chip, with 10M / 100M auto-negotiation RJ45 port PoE (Power over Ethernet) feature, 802.3af-compliant Fully isolated SMPS (Switch Mode Power Supply) 3x extended USB ports, compatible with USB 2.0 / 1.1 Angle rounded design, smooth hand feeling, 'simple snap' case lid Quality ABS material, dull polish surface, anti-fingerprint Comes with two different lids, changing as you like Included 1x PoE/ETH/USB Hub HAT kit 1x ABS case 1x Rubber feet 4pcs 1x Screws pack Downloads Documentation

    1 in stock

    € 29,95

    Members € 26,96

  • Waveshare Industrial 6-ch Relay Module for Raspberry Pi Zero

    Waveshare Waveshare Industrial 6-ch Relay Module for Raspberry Pi Zero

    This Industrial 6-Channel Relay Module is suitable for Raspberry Pi Zero with pre-soldered pinheader. It provides RS485/CAN Bus, Power Supply Isolation, and Photocoupler Isolation.Features RS485 half-duplex communication: using SP3485, UART control, auto RX/TX switch CAN half-duplex communication: using MCP2515 + SN65HVD230 solution, SPI control Onboard unibody power supply isolation, provides stable isolated voltage, needs no extra power supply for the isolated terminal Onboard photocoupler isolation, prevent interference from external high-voltage circuit connected to the relay Onboard TVS (Transient Voltage Suppressor), effectively suppress surge voltage and transient spike voltage in the circuit, lightningproof & anti-electrostatic Onboard resettable fuses and protection diodes, ensuring current/voltage stable output, preventing over current/voltage, better shock-resistance performance High quality relay, contact rating: ≤10A 250V AC or ≤10A 30V DC ABS protection enclosure with rail-mount support, easy to install, safe to use Comes with development resources and manual (wiringPi and python examples) Specifications Operating voltage: 7~36 V (industrial input voltage compatible) Relay channel: 6ch Communication Protocol: RS485, CAN Contact form: 1NO 1NC Included 1x ABS protection enclosure (top and bottom) 1x RPi Zero Relay 1x Screwdriver 1x OPTIONS 12 V, 1 A power adapter 1x Screws pack DownloadsDocumentation

    € 44,95

    Members € 40,46

  • Waveshare Ethernet/USB Hub Box for Raspberry Pi Zero (1x RJ45, 3x USB 2.0)

    Waveshare Waveshare Ethernet/USB Hub Box for Raspberry Pi Zero (1x RJ45, 3x USB 2.0)

    1 review

    The ETH-USB-Hub-Box is a Hub kit with ETH/USB Hub HAT (B) inside. It is tailored for Raspberry Pi Zero series, small in size, each cut-out of the case is exactly aligned with the connector. The case adopts classic Raspberry Pi red/white color combination, with quality dull polish surface, effectively keeping the Zero away from dust. This Hub Box will provide RJ45 Ethernet port and more USB capability for your Zero, make it easy to connect the Internet and sorts of USB devices. Features Designed for Raspberry Pi Zero, compatible with Zero series boards 3x extended USB ports, compatible with USB 2.0 / 1.1 Incorporates RTL8152B Ethernet chip, supports 1x RJ45 Ethernet port, 10/100M auto-negotiation Pogo pin design, for direct connecting with Raspberry Pi Zero/Zero W/Zero WH Angle rounded design, smooth hand feeling, 'simple snap' case lid Quality ABS material, dull polish surface, anti-fingerprint Comes with two different lids, changing as you like Included 1x ETH/USB Hub HAT (B) 1x ABS case 1x Rubber feet 4pcs 1x Screws pack 1x Screwdriver Downloads Documentation

    € 17,95

    Members € 16,16

  • KrakenSDR – Five-channel Software Defined Radio (based on RTL-SDR)

    KrakenSDR - Five-channel Software Defined Radio (based on RTL-SDR)

    1 review

    KrakenSDR is a phase-coherent software-defined radio with five RTL-SDRs KrakenSDR is a five-channel, RX-only, software-defined radio (SDR) based on the RTL-SDR and designed for phase-coherent applications and experiments. Phase-coherent SDR opens the door to some very interesting applications, including radio direction finding, passive radar, and beam forming. You can also use KrakenSDR as five separate radios. KrakenSDR is an upgraded version of the previous product, KerberosSDR. It provides a fifth receive channel, automatic phase-coherence synchronization capabilities, bias tees, a new RF design with cleaner spectrum, USB Type-C connectors, a heavy-duty enclosure, upgraded open source DAQ and DSP software, and an upgraded Android app for direction finding. RTL-SDR KrakenSDR makes use of five custom RTL-SDR circuits consisting of R820T2 and RTL2832U chips. The RTL-SDR is a well-known, low-cost software-defined radio (SDR), but throw five units together and using them on the same PC will not make them 'phase coherent;' each one will receive signals at a slightly different phase offset from the others. This makes it difficult or impossible to achieve a high degree of precision when measuring relationships between signals that arrive at different antennas. To achieve phase coherence, KrakenSDR drives all five RTL-SDR radios with a single clock source, and contains internal calibration hardware to allow the phase relationship between channels to be measured precisely and corrected for. Additionally, the overall design of KrakenSDR works to ensure phase stability, with care taken in the areas of heat management, driver configuration, power supply, and external-interference mitigation. Features Five-channel, coherent-capable RTL-SDR, all clocked to a single local oscillator Built-in automatic coherence synchronization hardware Automatic coherence synchronization and management via provided Linux software 24 MHz to 1766 MHz tuning Range (standard R820T2 RTL-SDR range, and possibly higher with hacked drivers) 4.5 V bias tee on each port Core DAQ and DSP software is open source and designed to run on a Raspberry Pi 4 Direction-finding software for Android (free for non-commercial use) Applications Physically locating an unknown transmitter of interest (e.g. illegal or interfering broadcasts, noise transmissions, or just as a curiosity) HAM radio experiments such as radio fox hunts or monitoring repeater abuse Tracking assets, wildlife, or domestic animals outside of network coverage through the use of low power beacons Locating emergency beacons for search-and-rescue teams Locating lost ships via VHF radio Passive radar detection of aircraft, boats, and drones Traffic-density monitoring via passive radar Beamforming Interferometry for radio astronomy Specifications Bandwidth 2.56 MHz RX Channels 5 Frequency Range 24-1766 MHz Radio Tuner 5x R820T2 Radio ADC 5x RTL2832U ADC Bit Depth 8-bits Oscillator Stability 1 PPM Typical Power Consumption 5 V/2.2 A (11 W) Enclosure Type Heavy-duty CNC Aluminum Dimensions 177 x 112.3 x 25.9 mm Weight 560 g Included 1x KrakenSDR (fully assembled and installed) with Aluminum enclosure 1x Manual Required USB Type-C cable 5 V/2.4 A USB Type-C power supply Antennas Raspberry Pi 4 (for computing) Android phone/tablet with mobile-hotspot capabilities (with direction finding) Downloads Wiki Android App

    € 549,00

    Members € 494,10

  • Seeed Studio CANBed – Arduino CAN-BUS Development Kit (ATmega32U4 with MCP2515 and MCP2551)

    Seeed Studio Seeed Studio CANBed - Arduino CAN-BUS Development Kit (ATmega32U4 with MCP2515 and MCP2551)

    Features ATmega32U4 with Arduino Leonardo bootloader on the board MCP2515 CAN Bus controller and MCP2551 CAN Bus transceiver OBD-II and CAN standard pinout selectable at the sub-D connector Compatible with Arduino IDE Parameter Value MCU ATmega32U4(with Arduino Leonardo bootloader) Clock Speed 16 MHz Flash Memory 32 KB SRAM 2.5 KB EEPROM 1 KB Operate Voltage(CAN-BUS) 9 V - 28 V Operate Voltage (MicroUSB) 5 V Input Interface sub-D Included CANBed PCBA sub-D connector 4PIN Terminal 2 x 4PIN 2.0 Connector 1 x 9x2 2.54 Header 1 x 3x2 2.54 Header

    € 32,95

    Members € 29,66

  • Seeed Studio Arduino Sensor Kit (Basis)

    Seeed Studio Seeed Studio Arduino Sensor Kit (Base)

    Features Co-produced by Arduino and Seeed Plug & play addition to the Arduino Uno 10 most commonly used electronics modules All modules are pre-wired on the PCB, no wiring is required High-quality online lessons provided by Arduino Perfect for Steam Education and Online Education Included Grove – LED Grove – Buzzer Grove – OLED Display 0.96″ Grove – Button Grove – Rotary Potentiometer Grove – Light Grove – Sound Grove – Temperature & Humidity Sensor Grove – Air Pressure Sensor Grove – 3-Axis Accelerator 6 Grove Cables

    € 42,95

    Members € 38,66

  • Seeed Studio CAN-BUS Shield V2 adopts MCP2515 en MCP2551

    Seeed Studio Seeed Studio CAN-BUS Shield V2 adopts MCP2515 and MCP2551

    Features Implements CAN V2.0B at up to 1 Mb/s Industrial standard 9 pin sub-D connector OBD-II and CAN standard pinout selectable. Changeable chip select pin Changeable CS pin for TF card slot Changeable INT pin Screw terminal that easily to connect CAN_H and CAN_L Arduino Uno pin headers Micro SD card holder 2 Grove connectors (I2C and UART) SPI Interface up to 10 MHz Standard (11 bit) and extended (29 bit) data and remote frames Two receive buffers with prioritized message storage

    € 32,95

    Members € 29,66

  • Seeed Studio ReSpeaker USB Mic Array (incl. Case)

    Seeed Studio Seeed Studio ReSpeaker USB Mic Array (incl. Case)

    Features Plug & Play (No driver required), compatible with Windows 10/8/7, Mac, Linux and Android that support OTG. Voice Pick-up device, Far-field voice pick-up up to 5m and supports 360° pick-up pattern Acoustic algorithms implemented: DOA(Direction of Arrival), AEC(Automatic Echo Cancellation), AGC(Automatic Gain Control), NS(Noise Suppression) Built-in audio jack, which allows for plugging in headphones or speakers (speaker not included) Applications Voice pick-up device Home/Office automation device In-car voice assistant Healthcare device Voice interaction robot Other applications Technical Specifications XVF-3000 from XMOS 4 High-Performance Digital Microphones Supports Far-field Voice Capture Speech Algorithms On-Chip 12 Programmable RGB LED Indicators Microphones: MEMS MSM261D4030H1CPM Sensitivity: -26 dBFS (Omnidirectional) Acoustic Overload Point: 120 dB SPL SNR: 63 dB Power Supply: 5V DC from Micro USB or Expansion Header Dimensions: 77mm (Diameter) 3.5mm Audio Jack Output Socket

    € 94,95

    Members € 85,46

  • Seeed Studio Deep Learning Starter Kit for Jetson Nano

    Seeed Studio Seeed Studio Deep Learning Starter Kit for Jetson Nano

    Features 32GB High-performance MicroSD card 5 V 4 A power supply with 2.1mm DC barrel connector 2-pin jumper Raspberry Pi camera module V2 Micro-B To Type-A USB cable with DATA enabled

    € 62,95

    Members € 56,66

  • Seeed Studio Grove Smart Agriculture Kit for Raspberry Pi 4

    Seeed Studio Seeed Studio Grove Smart Agriculture Kit for Raspberry Pi 4

    Features Easy-to-use and low-cost hardware kit: combines an affordable hardware kit with FREE curriculums and activities for students’ hands-on experience in precision agriculture techniques to food production. New tools for STEAM Education learners: students learn about AI, Machine learning, and IoT by building a garden monitoring system. Easily use with Raspberry Pi 4: with atmospheric and environmental sensors to understand their soil's health, analyze data, and make decisions. Real-time data collection: The student-built IoT devices connect to custom Microsoft Excel workbooks that collect real-time data using Excel’s Data Streamer. Building your own Machine Learning models: using Lobe.ai, students apply the technique to predict nutrient deficiencies in their plants and identifying pests in their garden. Introducing Microsoft responsible AI framework: engaging students with some of the social and ethical challenges raised by this new technology. Applications Combined with software and curriculum & resources, you can get hands-on experience, learn about artificial intelligence, machine learning, the Internet of Things, data science and then apply the knowledge in growing plants in the real world. This kit is highly suitable for use in different scenarios, no matter in the classroom, at home, at maker spaces/ fab labs or through distance learning courses: School garden monitoring Home garden monitoring Distance teaching /learning Online courses Hobby and DIY projects Included 1x Grove Base Hat for Raspberry Pi with a Fan 1x One Wire Temperature Sensor 1x Grove Capacitive Soil Moisture Sensor 1x Grove Sunlight Sensor 1x Grove Temperature & Humidity Sensor 1x Grove Relay 1x Grove Dual Button 1x micro SD Card with Card Reader (32 GB) 1x USB to TTL Serial Cable 1x Screwdriver Downloads FarmBeats for Student Kit Brochure FarmBeats Student Image

    € 114,95

    Members € 103,46

  • Seeed Studio Grove Beginner Kit for Arduino (Education Add-on Pack)

    Seeed Studio Seeed Studio Grove Beginner Kit for Arduino (Education Add-on Pack)

    Applications Suitable for Arduino beginners Suitable for infrared control and motion detect Suitable for getting started with open-source hardware and Arduino coding Part List 1 x Grove - Water Atomization 1 x Grove - Mini Fan 1 x Grove - Servo 1 x Grove - Ultrasonic Distance Sensor 1 x Grove - Infrared Receiver 1 x Grove - Mini PIR Motion Sensor 1 x Grove - Green Wrapper 1 x Grove - Blue Wrapper 5 x Grove Cable 1 x Infrared Remote Control Key 1 x Ultrasonic Sensor Bracket Set 1 x Motor Bracket Set 1 x Servo Base Please note: This is an add-on kit for the Seeed Studio Grove Beginner Kit for Arduino.

    € 52,95

    Members € 47,66

  • Makerfabs DIY ESP32 SmartClock Kit with Weather Forecasting

    Makerfabs Makerfabs DIY ESP32 SmartClock Kit with Weather Forecasting

    Out of stock

    This is a soldering kit for the starters to learn soldering. After 1-2 hours soldering and assembly, and easy steps to set the Wifi name/password with a phone, you will get: A real-time clock, it will get the world real-time from the Network timing protocol, you can set your local time zone easily An Alarm clock, with loud noise An Online world weather forecaster, about the local temperature/weather, you can easily change/alter your address/cities without any re-programming To reduce the soldering difficulty, all the SMD parts have been soldered, you only need to solder the THT parts, and then set the Wifi network with a phone, and finally turn on the power to enjoy the success. Included ESP32 SmartClock kit mainboard Batch of capacitors & resistors/connectors Colorful LCD module Lipo battery Acrylic boards Nuts & screws Downloads User Manual Source code on GitHub

    Out of stock

    € 34,95

    Members € 31,46

  • Raspberry Pi Pico for Radio Amateurs

    Elektor Publishing Raspberry Pi Pico for Radio Amateurs

    1 review

    Program and build RPi Pico-based ham station utilities, tools, and instruments Although much classical HF and mobile equipment is still in use by large numbers of amateurs, the use of computers and digital techniques has now become very popular among amateur radio operators. Nowadays, anyone can purchase a €5 Raspberry Pi Pico microcontroller board and develop many amateur radio projects using the “Pico” and some external components. This book is aimed at amateur radio enthusiasts, Electronic Engineering students, and anyone interested in learning to use the Raspberry Pi Pico to shape their electronic projects. The book is suitable for beginners in electronics as well as for those with wide experience. Step-by-step installation of the MicroPython programming environment is described. Some knowledge of the Python programming language is helpful to be able to comprehend and modify the projects given in the book. The book introduces the Raspberry Pi Pico and gives examples of many general-purpose, software-only projects that familiarize the reader with the Python programming language. In addition to the software-only projects tailored to the amateur radio operator, Chapter 6 in particular presents over 36 hardware-based projects for “hams”, including: Station mains power on/off control Radio station clock GPS based station geographical coordinates Radio station temperature and humidity Various waveform generation methods using software and hardware (DDS) Frequency counter Voltmeter / ammeter / ohmmeter / capacitance meter RF meter and RF attenuators Morse code exercisers RadioStation Click board Raspberry Pi Pico based FM radio Using Bluetooth and Wi-Fi with Raspberry Pi Pico Radio station security with RFID Audio amplifier module with rotary encoder volume control Morse decoder Using the FS1000A TX-RX modules to communicate with Arduino

    € 34,95

    Members € 31,46

  • Waveshare Mini Base Board (A) for Raspberry Pi Compute Module 4

    Waveshare Waveshare Mini Base Board (A) for Raspberry Pi Compute Module 4

    Specifications CM4 socket Suitable for all variants of Compute Module 4 Networking Gigabit Ethernet RJ45 connectorM.2 M KEY, supports communication modules or NVME SSD Connector Raspberry Pi 40-PIN GPIO header USB 2x USB 2.0 Type A2x USB 2.0 via FFC connector Display MIPI DSI display port (15-pin 1.0 mm FPC connector) Camera 2x MIPI CSI-2 camera port (15-pin 1.0 mm FPC connector) Video 2x HDMI port (including one port via FFC connector), supports 4K 30fps output RTC N/A Storage MicroSD card socket for Compute Module 4 Lite (without eMMC) variants Fan header No fan control, 5 V Power input 5 V Dimensions 85 x 56 mm Included 1x CM4-IO-BASE-A 1x SSD mounting screw Downloads Wiki

    € 24,95

    Members € 22,46

  • Seeed Studio Grove I²C Thermocouple Amplifier (MCP9600)

    Seeed Studio Seeed Studio Grove I²C Thermocouple Amplifier (MCP9600)

    Out of stock

    Features Integrated Cold-Junction Compensation Supported Types (designated by NIST ITS-90): Type K, J, T, N, S, E, B and R Four Programmable Temperature Alert Outputs: Monitor Hot- or Cold-Junction Temperatures Detect rising or falling temperatures Up to 255°C of Programmable Hysteresis Programmable Digital Filter for Temperature Low Power Dimensions: 20 mm x 40 mm x 18 mm Weight: 18 g Application Petrochemical Thermal Management Hand-Held Measurement Equipment Industrial Equipment Thermal Management Ovens Industrial Engine Thermal Monitor Temperature Detection Racks Downloads Eagle Files Github library Datasheet

    Out of stock

    € 22,95

    Members € 20,66

  • Seeed Studio Grove Capacitieve Vingerafdrukscanner/Sensor voor Arduino

    Seeed Studio Seeed Studio Grove Capacitive Fingerprint Scanner/Sensor for Arduino

    The Grove Capacitive Fingerprint Scanner/Sensor is based on the KCT203 Semiconductor fingerprint recognition module, including a high-performance MCU, a vertical RF push-type fingerprint sensor, and a touch sensing device. This module features many advantages such as small size, small fingerprint template, low power consumption, high reliability, fast fingerprint recognition, etc. In addition, it is worth mentioning that there is a lovely RGB light around this module to indicate whether the fingerprint recognition is successful. The system is equipped with a high-performance fingerprint algorithm, and the self-learning function is remarkable. After each successful fingerprint recognition, the latest challenge feature values can be integrated into the fingerprint database to continuously improve the fingerprint features, making the experience better. Applications Fingerprint lock devices: door locks, safes, steering wheel locks, padlocks, gun locks, etc. Fingerprint sign-in, access control system Specifications CPU GD32 Fingerprint Template Storage Max. 100 Connector Grove UART Sensor Resolution 508 DPI Sensor Pixel 160x160 False Rejection Rate <1% False Acceptance Rate <0.005% Match Response Time(1:N Mode) <350ms Match Response Time(1:1 Mode) <7ms Sensor Size Φ14.9mm Frame Size Φ 19mm Power Consumption Full speed: ≤40 mA; Sleep: ≤12 uA Operating Voltage 3.3 V / 5 V Operating Temperature -20 ~ 70 ℃ ESD Protection Non-contact 15 KV, contact 8 KV Included 1x KCT203 Semiconductor fingerprint recognition module 1x Sensor cable 1x Grove cable 1x Grove driver board Documentations Grove Capacitive Fingerprint Scanner/Sensor eagle file Grove Capacitive Fingerprint Scanner/Sensor code Wiki

    € 32,95

    Members € 29,66

  • Seeed Studio Grove Multi-channel Gas Sensor v2

    Seeed Studio Seeed Studio Grove Multi-channel Gas Sensor v2

    Features Four fully independent sensor elements on one package. The ability to detect a variety of gases, besides Carbon monoxide (CO), Nitrogen dioxide (NO2), Ethyl alcohol(C2H5CH), Volatile Organic Compounds (VOC), etc. Qualitative detecting, rather than quantitative. Compact size for easy deployment. Included 1 x Multichannel gas sensor board 1 x Grove cable

    € 44,95

    Members € 40,46

  • Seeed Studio Grove SGP30 VOC & eCO2 Gas Sensor (Arduino-compatible)

    Seeed Studio Seeed Studio Grove SGP30 VOC & eCO2 Gas Sensor (Arduino-compatible)

    The Sensirion SGP30 is a digital multi-pixel gas sensor that can easily integrate with air purifiers, demand-controlled ventilation, and other IoT applications. Powered by Sensirion’s CMOSens®technology, it integrates a complete sensor system on a single chip featuring a digital I2C interface, a temperature-controlled micro hotplate, and two preprocessed indoor air quality signals. As the first metal-oxide gas sensor featuring multiple sensing elements on one chip, the SGP30 provides more detailed information about air quality. Features Multi-pixel gas sensor for indoor air quality applications Outstanding long-term stability I2C interface with TVOC and CO2eq output signals Low power consumption Chip module tape and reel packaged, reflow solderable Specifications Weight: 9g Battery: Exclude Working Voltage: 3.3V/5V Output range: TVOC-0 ppb to 60000ppb / CO₂eq - 400 ppm to 60000 ppm Sampling rate: 1 Hz

    € 22,95

    Members € 20,66

  • Seeed Studio Grove GPS Module

    Seeed Studio Seeed Studio Grove GPS Module

    1 review

    Features Supports NMEA and U-Blox 6 protocols. Low power consumption Baud rates configurable Grove UART interface Specifications Dimensions 40 mm x 20 mm x 13 mm Update Rate 1 Hz, max 10 Hz Baud Rate 9,600 – 115,200 Input Voltage 3.3 V / 5 V Navigation Sensitivity -160dBm Power Requirements 3.3/5V Number of Channels 22 tracking, 66 channels Time to first start Cold start: 13s Warm start: 1-2s Hot start: < 1s Antennas Antenna included Accuracy 2.5m GPS Horizontal Position Accuracy

    € 29,95

    Members € 26,96

  • Seeed Studio Grove EMG Detector

    Seeed Studio Seeed Studio Grove EMG Detector

    Features Grove Compatible 3.5mm Connector 6 Disposable Surface Electrodes Power supply voltage: 3.3V-5V 1000mm Cable Leads No additional power supply Specifications Dimensions: 140 mm x 100 mm x 30 mm Weight: 45 g Battery: Exclude Part List 1 x Grove - EMG Detector 1 x Grove Cable 6 x One-off electrode 1 x DC jacket to button connector cable 1000mm

    € 37,95

    Members € 34,16

  • Seeed Studio GrovePi+ Add-on Board for Raspberry Pi

    Seeed Studio Seeed Studio GrovePi+ Add-on Board for Raspberry Pi

    The GrovePi+ is an easy-to-use and modular system for hardware hacking with the Raspberry Pi, no need for soldering or breadboards: plug in your Grove sensors and start programming directly. Grove is an easy-to-use collection of more than 100 inexpensive plug-and-play modules that sense and control the physical world. By connecting Grove Sensors to Raspberry Pi, it empowers your Pi in the physical world. With hundreds of sensors to choose from Grove families, the possibilities for interaction are endless. Set-up in 4 simple steps Slip the GrovePi+ board over your Raspberry Pi Connect the Grove modules to the GrovePi+ board Upload your program to Raspberry Pi Begin taking in the world data Please note: Raspberry Pi board is not included

    € 49,95

    Members € 44,96

  • Seeed Studio Grove Starter Kit voor Raspberry Pi Pico

    Seeed Studio Seeed Studio Grove Starter Kit for Raspberry Pi Pico

    Features Get Started with Raspberry Pi Pico easily and quickly 14 handpicked Grove Modules, including 5 sensors/ 5 actuators/ 2LED/ 1 LCD display/ 1 Grove shield Detailed and comprehensive Micropython tutorials for each module (Arduino Guide is on the way) No wiring, no welding, plug & play experience Included 1 x Grove - LED Pack 1 x Grove - RGB LED (WS2813 Mini) 1 x Grove - Light Sensor 1 x Grove - Sound Sensor 1 x Grove - Rotary Angle Sensor 1 x Grove - Temperature & Humidity Sensor 1 x Grove - mini PIR motion sensor 1 x Grove - Passive Buzzer 1 x Grove - Button 1 x Grove - Servo 1 x Grove - Mini Fan 1 x Grove - Relay 1 x Grove - 16x2 LCD 1 x Grove Shield for Pi Pico 8 x Grove Cable

    € 54,95

    Members € 49,46

  • Seeed Studio GrovePi+ Starter Kit for Raspberry Pi

    Seeed Studio Seeed Studio GrovePi+ Starter Kit for Raspberry Pi

    GrovePi+ is stacked on top of the Raspberry Pi without the need for any other connections. Communication between the two occurs over the I2C interface. All Grove modules connect to the universal Grove connectors on the GrovePi+ shield via the universal 4 pin connector cable. Grove modules work on analog and digital signals and can be connected directly to the ATMEGA328 microcontroller on the Grove Pi+. The microcontroller acts as an interpreter between the Raspberry Pi and the Grove sensors. It sends, receives, and executes commands sent by the Raspberry Pi. Features One GrovePi+ board together with 12 popular Grove sensors and 10 Grove cables GrovePi+ is compatible with Raspberry Pi A+, B, B+ / 2, 3, 4. CE certified and compatible with Linux and Win 10 IoT. Included 1x Grove Pi+ 1x Grove - Rotary Angle Sensor 1x Grove - Sound Sensor 1x Grove - LCD RGB Backlight 1x Grove - Temp&Humi Sensor 1x Grove - Red LED 1x Grove - Light Sensor 1x Grove - Buzzer 1x Grove - Relay 1x Grove - Blue LED 1x Grove - Button 1x GrovePi+ Guidebook 10x Cables 1x Grove - UItrasonic Ranger 1x Grove - Green LED

    € 109,95

    Members € 98,96

  • Seeed Studio Grove SCD30 CO2, Temperatuur & Vochtigheid Sensor voor Arduino

    Seeed Studio Seeed Studio Grove SCD30 CO2, Temperature & Humidity Sensor for Arduino

    Features NDIR CO2 sensor technology: embedded with Sensirion SCD30 Multi-function: Integrates temperature and humidity sensor on the same sensor module High precision and wide measurement accuracy: ±(30 ppm + 3%) between 400 ppm to 10000 ppm Superior stability: Dual-channel detection Easy project operation: Digital interface I²C, Breadboard-friendly, Grove-compatible Best performance-to-price ratio Application Ideas Air Purifier Environmental Monitoring Plant Environmental Monitoring system Arduino weather station

    € 99,95

    Members € 89,96

Login

Forgot password?

Don't have an account yet?
Create an account