Displays

29 products


  • HyperPixel 4.0 – Hi-Res Display for Raspberry Pi (Touch Version)

    Pimoroni HyperPixel 4.0 - Hi-Res Display for Raspberry Pi (Touch Version)

    HyperPixel 4.0 is the perfect way to use your RPi without a bunch of cables or a bulky display. Design your own interface to control your project, display data, or turn your Pi into a tiny media centre. This version of HyperPixel has a gorgeous IPS display, with wide viewing angles, custom-made cover glass, and the alternate I²C interface is broken out for advanced users. Features High-speed DPI interface 4.0' IPS (wide viewing angle, 160°) display (86.4 x 51.8 mm) 800x480 pixels (~235 PPI) 18-bit colour (262,144 colors) 60 FPS frame rate Contrast ratio: 500:1 Capacitive touch 40-pin female header included to boost height for Raspberry Pi B+, 2, 3, 3B+ and 4 Standoffs included to securely attach to your RPi Compatible with all 40-pin header Raspberry Pi models One-line installer Dimensions: 58.5 x 97 x 12 mm (WxHxD, depth includes header and display) HyperPixel uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays use. It has a 60 FPS frame rate and a resolution of approximately 235 pixels per inch (800x480) on its 4.0' display. The display can show 18-bits of colour (262,144 colors). This Touch version has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch! Everything comes fully-assembled, and there's no soldering required! The display is securely stuck down to the HyperPixel 4.0 PCB and connected via a neat little flush-mounting FPC cable. Just pop HyperPixel 4.0 on your RPi and run our installer to get everything set up! Please note: when installing HyperPixel 4.0 onto your RPi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel. It'll work with any 40-pin version of the RPi, including RPi Zero and RPi Zero W. If you're using it with a larger RPi then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Zero or Zero W then just pop it straight onto the GPIO. The included standoff kit allows you to mount your HyperPixel 4.0 safely and securely to your RPi. Just screw them into the posts on the underside of the HyperPixel 4.0 PCB and then secure with screws through the mounting holes on your RPi. Downloads GitHub

    € 79,95

    Members € 71,96

  • Waveshare 4-digit 8-segment Display Module for Raspberry Pi Pico

    Waveshare Waveshare 4-digit 8-segment Display Module for Raspberry Pi Pico

    Features SPI-compatible, easy to drive Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Digits 4 Dispaly size 0.4 inch LED color red Driver 74HC595 Display part no. FJ4401AH Dimensions 52 × 21 mm

    € 9,95

    Members € 8,96

  •  -46% Case for 7` RGB-Touch-Display for Raspberry Pi

    JOY-iT Case for 7" RGB-Touch-Display for Raspberry Pi

    Case for 7' RGB-Touch-Display for Raspberry Pi

    € 12,95€ 6,95

    Members identical

  • "Waveshare 3.5\" Touch Display Module for Raspberry Pi Pico (480x320)"

    Waveshare "Waveshare 3.5\" Touch Display Module for Raspberry Pi Pico (480x320)"

    Features 480 x 320 resolution, IPS screen, 65K colors, clear and colorful displaying effect Dedicated touch controller, bringing more smooth touching effect than AD-controlled solutions MicroSD card slot for storing images and direct displaying them easily Programmable backlight control, power saving Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 5 V Resolution 480 x 320 pixels Communication interface SPI Display size 73.44 x 48.96 mm Display panel IPS Pixel size 0.153 x 0.153 mm Driver ILI9488 Dimensions 86.00 x 57.20 mm Touch controller XPT2046 Downloads Wiki

    € 29,95

    Members € 26,96

  • Pimoroni Raspberry Pi Pico Display Pack

    Pimoroni Pimoroni Raspberry Pi Pico Display Pack

    Pico Display lets you turn a Pico into a compact user interface device for a bigger project, capable of giving instructions, displaying readouts and even incorporating elaborate nested menus. If you'd rather use your Pico as a standalone device you could make a little rotating slideshow of images, display beautiful graphs from sensor data or build your own Tamagotchi or matchbox sized text adventure game.Features 1.14” 240x135 pixel IPS LCD screen 4 x tactile buttons RGB LED Pre-soldered female headers for attaching to Pico Compatible with Raspberry Pi Pico. Fully assembled No soldering required (as long as your Pico has header pins attached). Dimensions: approx 53 x 25 x 9 mm (L x W x H) Screen usable area: approx 25 x 15 mm (L x W) C/C++ and MicroPython libraries

    € 19,95

    Members € 17,96

  • HyperPixel 2.1 Round – Hi-Res Display for Raspberry Pi

    Pimoroni HyperPixel 2.1 Round - Hi-Res Display for Raspberry Pi

    HyperPixel 2.1 Round has all the great features of other HyperPixels – crisp, brilliant IPS display touchscreen, and high-speed DPI interface – it's just rounder! You can use it with any Raspberry Pi with a 40-pin header but it works particularly nicely with the RPi Zero footprint – it's designed so you can mount a Zero neatly behind it, so you can't see the RPi when you look at it from the front.This version of HyperPixel would be great for custom interfaces and control panels – mounted on a wall it would make a really neat, minimalist smart home controller or a stylish 'what's playing' display for your sound system. Everything is pre-soldered and ready to go, just pop it onto your RPi, install the software, and away you go!HyperPixel 2.1 Round uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 229 pixels per inch (480x480px) on its 2.1' display. The display can show 18-bits of colour (262,144 colors).Features High-speed DPI interface 2.1' IPS (wide viewing angle, 175°) display 480x480 pixels, minus the corners (~229 PPI) 18-bit colour (262,144 colors) 60 FPS frame rate Active area: 53.28 x 53.28 mm Capacitive touchscreen (with Python library) Compatible with all 40-pin header Raspberry Pi models Dimensions: 71.80 x 71.80 x 10.8 mm (WxHxD, depth includes header and display). With a RPi Zero attached with short standoffs, the total depth is 17 mm. Downloads Display library for Raspberry Pi OS Python touchscreen library Dimensional drawing Pinout

    € 79,95

    Members € 71,96

  • HyperPixel 4.0 Square Touch – Hi-Res Display for Raspberry Pi

    Pimoroni HyperPixel 4.0 Square Touch - Hi-Res Display for Raspberry Pi

    Out of stock

    HyperPixel 4.0 Square has all the great features of our standard HyperPixel 4.0 – a crisp, brilliant IPS display with touchscreen, and high-speed DPI interface – it's just more square!This square version of HyperPixel 4.0 is great for custom interfaces and control panels, and works really well for Pico-8 games. Everything is pre-soldered and ready to go, just pop it onto your RPi, run our installer, and away you go!Features High-speed DPI interface 4.0' IPS (wide viewing angle, 160°) display (72x72 mm) 720x720 pixels (~254 PPI) 18-bit colour (262,144 colors) 60 FPS frame rate Optional capacitive touchscreen 40-pin female header included to boost height for Raspberry Pi B+, 2, 3, 3B+ and 4 Standoffs included to securely attach to your RPi Compatible with all 40-pin header Raspberry Pi models One-line installer HyperPixel 4.0 Square uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small RPi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 254 pixels per inch (720x720px) on its 4.0' display. The display can show 18-bits of colour (262,144 colors).This Touch version has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch!Please note: when installing HyperPixel 4.0 Square onto your RPi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel.It'll work with any 40-pin version of the RPi, including RPi Zero and RPi Zero W. If you're using it with a larger RPi then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Zero or Zero W then just pop it straight onto the GPIO.The included standoff kit allows you to mount your HyperPixel 4.0 Square safely and securely to your RPi. Just screw them into the posts on the underside of the HyperPixel 4.0 Square PCB and then secure with screws through the mounting holes on your RPi.DownloadsGitHub

    Out of stock

    € 79,95

    Members € 71,96

  • Waveshare 5.65` ACeP 7-Color E-Paper E-Ink Display Module (600x448)

    Waveshare Waveshare 5.65" ACeP 7-Color E-Paper E-Ink Display Module (600x448)

    Features Advanced Color ePaper (ACeP) technology, supports 7-color display No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc. Onboard voltage translator, compatible with 3.3/5 V MCUs Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32) Specifications Operating voltage 3.3/5 V Display color ACeP 7-Color Interface 3-wire SPI, 4-wire SPI Grey scale 2 Outline dimensions 138.5 x 100.5 mm Full refresh time <35s Display size 114.9 x 85.8 mm Refresh power 50 mW (typ.) Dot pitch 0.1915 x 0.1915 mm Standby time <0.01 uA (almost none) Resolution 600 x 448 pixels Viewing angle >170° Downloads Wiki

    € 69,95

    Members € 62,96

  • "Waveshare 2.13\" Touch E-Paper E-Ink Display for Raspberry Pi Zero (incl. Case)"

    Waveshare "Waveshare 2.13\" Touch E-Paper E-Ink Display for Raspberry Pi Zero (incl. Case)"

    Features 2.13' capacitive touch e-Paper display, 5-point touch, 250×122 pixels Supports waken up by user-defined gesture No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi Zero / Zero W Comes with development resources and manual (examples for Raspberry Pi) Included 1x 2.13inch Touch e-Paper HAT 1x ABS case 1x Screwdriver 1x Thermal tape 1x Rubber feet 4pcs 2x Screws Downloads Documentation

    € 34,95

    Members € 31,46

  • Pimoroni Display HAT Mini for Raspberry Pi Zero

    Pimoroni Pimoroni Display HAT Mini for Raspberry Pi Zero

    Display HAT Mini features a bright 18-bit capable 320x240 pixel display with vibrant colours and formidable IPS viewing angles, connected via SPI. It's got four tactile buttons for interacting with your Raspberry Pi with your digits and a RGB LED for notifications. A QwST connector (Qwiic / STEMMA QT) and a Breakout Garden header is also squeezed in so it's a doddle to connect up different kinds of breakouts. It will work with any model of Raspberry Pi with a 40 pin header, but we think it goes with the Raspberry Pi Zero particularly well - we've included a pair of standoffs so you can use to bolt HAT and Raspberry Pi together to make a sturdy little unit. To accommodate the screen Display HAT Mini is a bit bigger than a standard mini HAT or pHAT – it's around 5 mm taller than a Raspberry Pi Zero (so a Mini HAT XL or a Mini HAT Pro, if you will). Display HAT Mini lets you turn a Raspberry Pi into a convenient IoT control panel, a tiny photo frame, digital art display or gif-box, or a desktop display for news headlines, tweets, or other info from online APIs. This screen is a handy 3:2 ratio, useful for retro gaming purposes! Features 2.0” 320x240 pixel IPS LCD screen, connected via SPI (~220 PPI, 65K colours) 4x tactile buttons RGB LED Qw/ST (Qwiic/STEMMA QT) connector Breakout Garden / I²C header Pre-soldered socket header for attaching to Raspberry Pi Compatible with all models of Raspberry Pi with a 40-pin header. Fully assembled No soldering required (as long as your RPi has header pins attached). Dimensions: approx 65.5 x 35 x 9 mm (W x H x D, includes header and display). With a Raspberry Pi Zero attached with standoffs, the total depth is 17 mm. Screen usable area: 40.8 x 30.6 mm (L x W) Pinout Schematic Dimensional drawing Display HAT Mini Python library ST7789 Python library Included Display HAT Mini 2x 10 mm standoffs

    € 32,95

    Members € 29,66

  • JOY-iT Raspberry Pi Controllerboard for RGB-LED Matrix

    JOY-iT JOY-iT Raspberry Pi Controllerboard for RGB-LED Matrix

    3 in stock

    FUNCTION Logic level converter from 3.3 V to 5V for controlling of up to 3 LED matrix rows PASSIVE AND ACTIVE COOLING Aluminium heatsink with a 25x25mm sized fan COMPATIBLE WITH Raspberry Pi 3A/B/A+/B+, 4B INPUT VOLTAGE 5 Volt INTERFACES 3x HUB75 plugs DATA LINE E SWITCHABLE with jumpers to Pin 4 or 8 DIMENSIONS 65 x 56 x 26 mm WEIGHT 40 g ITEMS SHIPPED Controller, heatsink, fan, 2 spacers, 6 screws and nuts, 4 flat washers, 2 jumpers EAN 4250236819631 ARTICLE NO. RB-MatrixCtrl

    3 in stock

    € 15,95

    Members € 14,36

  • Last stock! Joy-Pi Note – 11,6` Raspberry Pi 4-gebaseerde Notebook

    JOY-iT Joy-Pi Note - 11.6” Raspberry Pi 4-based Notebook

    1 in stock

    3-in-1 Solution: Notebook, Learning Platform and Experiment Center The Joy-Pi Note is the new flagship in the Joy-Pi family. With its 11.6' IPS screen and a detachable, wireless keyboard, it takes the Joy-Pi‘s basic concept in a new, high-quality and attractive format. With 46 courses and 18 projects, the Joy-Pi Note is not only suitable as an experiment center, but is also ideal for use in the education sector. With over 22 integrated sensors and modules, there are no limits to the user‘s own joy of experimentation. This simplifies the introduction to electrical engineering and programming. Due to the installed learning platform, which was developed especially for the Joy-Pi Note, the installed units can be operated and learned independently of one‘s own previous knowledge. It is also possible to connect additional sensors and modules via the pins of the Raspberry Pi, which are routed to the outside, and thus also carry out more complex projects. Of course, the Joy-Pi Note can also be used as a „classic“ notebook. All programs compatible with the Raspberry Pi 4 can be installed. The integrated 2 MP camera also makes video conferencing possible, for example. All Raspberry Pi 4 models can be used (we recommend 4 GB RAM or higher). On the bottom of the device, you will find a compartment where you can insert a power bank to also operate the Joy-Pi Note mobile. Specifications Main Features Screen 11.6' 1920x1080 IPS LCD Camera 2 MP Special features Fully equipped set, completely integrated experiment center, pre-installed learning platform, detachable wireless keyboard, integrated compartment for powerbank & accessories Lessons of the learning platform 46 courses & 18 projects for Python and Scratch Power supply 12 V hollow plug, 5 V USB Compatible to Raspberry Pi 4 (4 GB and 8 GB RAM) Keyboard layouts DE (default) + US, UK, FR, IT, PT and Nordic Dimensions 291 x 190 x 46 mm Weight 1.3 kg Included sensors, modules & accessories Display 7-segment display, 16x2 LCD module, 8x8 RGB Matrix Sensors DHT11 temperature & humidity sensor, tilt sensor, motion sensor, sound sensor, touch sensor, RFID module, light sensor, ultrasonic distance sensor Motors Servo interface, stepper motor interface, vibration motor Control Joystick, 4x4 button matrix, Raspberry Pi & PCB connection switch, motion sensor, sensitivity controller, sound sensor sensitivity controller, 16x2 LCD module brightness controller Others Relay, fan, GPIO extension, GPIO LED indicator, breadboard, IO/ADC/I²C/UART expansion interface, infrared sensor interface, buzzer, display driver Accessories RFID chip, RFID card, 12 V power supply, servo motor, stepper motor, infrared receiver, infrared remote control, DC motor with fan attachment, HDMI connector, screwdriver, microSD card (32 GB), SD card reader, electronic accessories, wireless mouse, wireless keyboard Included Joy-Pi Note Accessories Quick guide Required Raspberry Pi 4 (4 GB or 8 GB RAM)

    1 in stock

    € 399,00

    Members € 359,10

  • JOY-iT 3.5' Touchscreen for Raspberry Pi

    JOY-iT "JOY-iT 3.5\" Touchscreen for Raspberry Pi"

    With the 3.5 inch large TFT touch screen display, you can build a mini tablet PC based on a Raspberry Pi. The display, with a maximum resolution of 480x320 pixels, is simply plugged into the existing GPIO connectors. Specifications Display: 3.5' (8.89 cm) Resolution: 480x320 pixels Touchscreen Type: Resistive Touch screen controller: XPT2046 Colors: 65536 Backlight: LED Connection: GPIO header Aspect ratio: 8:5 Display Size: 85 x 56 mm

    € 34,95

    Members € 31,46

  • "Waveshare 2.66\" E-Paper E-Ink Display Module for Raspberry Pi Pico (296x152)"

    Waveshare Waveshare 2.66" E-Paper E-Ink Display Module for Raspberry Pi Pico (296x152)

    Features No backlight, keeps displaying last content for a long time even when power down Ultra low power consumption, basically power is only required for refreshing SPI interface, requires minimal IO pins Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Operating voltage 3.3 V Display color red, black, white Interface 3-wire SPI, 4-wire SPI Grey scale 2 Outline dimensions 74.00 × 37.5 0mm Full refresh time 15s Display size 60.088 × 30.704 mm Refresh power 42.4 mW (typ.) Dot pitch 0.203 × 0.202 mm Standby current <0.01 uA (almost none) Resolution 296×152 pixels Viewing angle >170° Downloads Wiki

    € 27,95

    Members € 25,16

  • Waveshare 2.23` OLED Display Module for Raspberry Pi Pico (128x32)

    Waveshare Waveshare 2.23" OLED Display Module for Raspberry Pi Pico (128x32)

    Features Adopts both 4-wire SPI and I²C interface, better compatibility, fast data rate Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples) Specifications Logical voltage 3.3 V Viewing angle >160° Operating voltage 3.3 V/5 V Resolution 128×32 pixels Communication interface 4-wire SPI, I²C Display size 55.02 × 13.10 mm Display panel OLED Pixel size 0.41 × 0.39 mm Driver SSD1305 Dimensions 63.00 × 26.00 mm

    € 19,95

    Members € 17,96

  • Raspberry Pi 7” Touchscreen Display

    Raspberry Pi Foundation "Official 7\" Touchscreen for Raspberry Pi"

    1 review

    Out of stock

    The 800 x 480 7' Touch Display features a full color display connects through an adapter board that is included in the kit. All necessary drivers to support the 10-finger capacitive touch features as well as an on-screen keyboard are integrated into the latest Raspbian OS to work completely free of keyboard or mouse. What's in the box:• 7” Official RPi Touch Display• The Adapter Board• A DSI Flexcable• Four stand-offs and screws (for mounting the adapter board and RPi board to the display)• Four jumper wires (for connecting the power from the Adapter Board and the GPIO pins on the RPi powering both units) Screen specifications:• 7” Touch Display• Dimensions: 194 x 110 x 20 mm• Actual screensize: 155 x 86 mm• Resolution: 800 x 480 px• 10 finger capacitive touch This display will work with:• Raspberry Pi Model A+• Raspberry Pi 1 Model B+• Raspberry Pi 2 Model B• Raspberry Pi 3 Model B• Raspberry Pi 3 Model B+ Although future software updates are expected to enable the display to be used on a Model B or A. Please note that the position of the mounting spaces on the screen will not support these older models. Read more about this by following the link:www.elektormagazine.com/news/the-pi-gets-an-official-touchscreen

    Out of stock

    € 82,95

    Members € 74,66

  • Last stock! "\"JOY-iT 10\"Touchscreen voor RPi incl. metalen behuizing en stand (HDMI/VGA/BNC/AV)\"\"\""

    JOY-iT "JOY-iT 10\" Touchscreen for RPi incl. Metal Case and Stand (HDMI/VGA/BNC/AV)"

    1 review

    2 in stock

    The 10' Touch-Display from JOY-iT is housed in a sleek metal case making it the perfect choice for a wide range of applications. The case is robust and has a smooth matt black finish which blends well with the hard-coated (3H) screen. Included with the display is an adapter plate which can be used to mount any of the standard single board computers on the rear of the unit. The USB socket can power the display when it’s used with an SBC so there will be no need to use the included mains adapter. The display can also be used as a monitor for standard PC systems via the HDMI and VGA connectors. A BNC and AV connector provide analog inputs for CCTV etc. Features Includes an adapter plate for mounting all the standard Single Board Computers (SBC) such as Raspberry Pi, BeagleBone, CubieBoard etc. Needs no separate mains adapter when used with an SBC Robust metal case Anti-glare display Hard coated (3H) display surface Specifications Display size 10.1” (25.65 cm) Visible display surface 217 x 135.6 mm Resolution 1280(RGB) x 800(WXGA) pixel Contrast ratio 800:1 Bracket and stand Included HDMI connector 1x VGA connector 1x AV connector 1x BNC connector 1x USB connector 2x Integrated loudspeaker Yes Mains adapter 12 V / 2000 mA Operating Temperature 0 ~ 50°C Brightness 350 cd/m² Displayed colors 16.7 million Special features Hard coated (3H) anti-glare display Weight 1.20 kg Dimensions without stand 244 x 163 x 32 mm (B x H x T) Included Display (10.1”) Stand Adapter plate for mounting an SBC HDMI cable USB cable (Type A) USB cable (Type A to Micro-USB) Mains adapter Remote controller Downloads Pre-installed Raspbian System for Raspberry Pi 4 Pre-installed Raspbian System for Raspberry Pi 3B+ and older

    2 in stock

    € 199,95

    Members € 179,96

  • JOY-iT 5` Touchscreen for Raspberry Pi

    JOY-iT JOY-iT 5" Touchscreen for Raspberry Pi

    Display: 5' (12.7 cm) Weight: 159 g Resolution: 800 x 480 pixels Display Type: Touch-Control Amount HDMI-HDMI Adapter: 1x Micro USB Interface (only Power): 1x Supports Raspberry: Raspbian, Ubuntu Dimensions, without mounting: 120 x 79 x 7 mm Scope of supply: 5 inch HDMI LCD, HDMI-HDMI Adapter, Touchpen

    € 62,95

    Members € 56,66

  • Last stock! JOY-iT 7` Touchscreen for Raspberry Pi

    JOY-iT JOY-iT 7" Touchscreen for Raspberry Pi

    1 in stock

    Resolution: 1024 x 800 pixels Supported Devices: Raspberry Pi A+/ B+/ 2B / 3B, Banana Pi, Banana Pro, Windows-PCs Special features: Can also be used as an independent HDMI-Display LCD Type: TFT Connections: HDMI, Micro-USB Touch Controller: GT811 Touch-Panel: Type Capacitive (5 Multi-Touch) Backlight: LED Display-Size: 154.21 x 85.92 mm

    1 in stock

    € 79,95

    Members € 71,96

  • Picade Desktop Retro Arcade Machine (10-inch Display)

    Pimoroni Picade Desktop Retro Arcade Machine (10-inch Display)

    With the Picade Desktop Retro Arcade Machine (10-inch Display) you can build your very own arcade machine. Cabinet Features Black, powder-coated panels Joystick with black ball top Acrylic marquee and console with authentic artwork Dedicated illuminated power button Push-fit arcade buttons Easy access with removable back panel 3' speaker (5 W, 4 Ω) Grippy rubber feet Dimensions: 350 x 230 x 210 mm 1024x768 (4:3 ratio) IPS (wide viewing angle) display Pimoroni-designed and manufactured HDMI display driver board and keypad controls Powered by micro-USB cable (included) from your Pi Picade X HAT Features Easy DuPont connectors for buttons and joystick Push-fit speaker terminals USB-C power management, power switch pins, and power button I²S audio DAC with 3 W amplifier (mono) 4-way joystick inputs 4 utility buttons 6 player buttons Metal standoffs to hold your Picade X HAT securely Included Picade enamel pin badge Pimoroni Super Sticker Selection Picade poster/assembly instructions Please note: You will need to add a Raspberry Pi, USB-C power supply, and a MicroSD Card.

    € 349,00

    Members € 314,10

  • PicoBoy Mini Game Console

    PicoBoy Mini Game Console

    The Picoboy is a powerful mini handheld measuring just 3 x 5 cm. It is suitable for learning programming, developing your own games or simply playing with it. An introduction to programming with the Arduino IDE and MicroPython is available. All you need is a PC, the PicoBoy and a USB-C cable. As the PicoBoy is compatible with the Raspberry Pi Pico and the Arduino IDE, there are countless other tutorials, examples and libraries on the internet to make programming easier. Specifications 1.3' OLED display with 128 x 64 pixels (black/white) RP2040 microcontroller makes it compatible with the Raspberry Pi Pico 2x 133 MHz ARM M0+ 2 MB Flash 264 KB RAM USB-C interface for programming and data transfer 3 Pre-installed games 5-way joystick Acceleration sensor (can now also be used in Python!) Power supply via USB-C or a CR2032 button cell Dimensions: 49,2 x 29,1 x 14,5 mm Downloads GitHub

    € 29,95

    Members € 26,96

  • Waveshare 7" Capacitive Touch Display Kit for Raspberry Pi Zero (1024x600)

    Waveshare Waveshare 7" Capacitive Touch Display Kit for Raspberry Pi Zero (1024x600)

    The Zero-DISP-7A is a 7″ touch display kit for Raspberry Pi Zero with IPS Display Expansion Board featuring 1024x600 pixels and 5-point capacitive touch. Features 7-inch IPS touch display with a hardware resolution of 1024x600. 5-point touch control, toughened glass panel with up to 6H hardness. When working with Raspberry Pi Zero, supports Raspberry Pi OS, Ubuntu, Kali, and Retropie systems. Onboard ETH/USB HUB function, adapting RJ45 and USB port serving as an alii-in-one mini computer. Onboard 4-pin speaker header and 3.5 mm audio jack, support for HDMI audio output. Specifications Zero connectors Mini HDMI port, 2x USB Micro male port (1x HUB, 1x Power supply) Display 7-inch 1024 x 600 pixels, 5-point capacitive touch Networking 100M Ethernet RJ45 port USB 2x USB 2.0 port Audio Headphone jack, 4-pin speaker header Power input USB Type-C Interface, 5V Included 1x Zero-DISP-7A 1x Button board 1x Button board cable (9 cm) 4x White nylon spacer Downloads Wiki

    € 64,95

    Members € 58,46

  • Soldered Inkplate 6COLOR (with E-paper)

    Soldered Soldered Inkplate 6COLOR (with E-paper)

    3 in stock

    Inkplate 6COLOR continues the tradition of the well-known, user-friendly Inkplate series which is compatible with Arduino and Micropython. Inkplate 6COLOR offers a unique innovation – the ability to display colors on the screen. Inkplate 6COLOR has a 5.85" folded e-paper that displays a total of 7 different colors (Black, White, Red, Yellow, Blue, Green, and Orange). Considering the built-in dithering capability, the results you can get on the screen are really impressive. Powered by ESP32, you will have strong microcontroller with WiFi and Bluetooth on your disposal. It’s super-low-power (18 uA) so you can use it for days, weeks, or months out of a single battery charge. Using our Arduino library (100% compatible with Adafruit GFX), it’s 5 minute work to get the board running for you. The Micropython module is available as well. It’s 100% open-source for both software and hardware. What is especially interesting is that Inkplate uses recycled screens taken from old e-book readers, which is very environmentally friendly, but you have to keep in mind that some screens may have small scratches because of this. All screens with large scratches and damages are not used at all. Features 5.85-inch, 600x448 pixel electronic paper with the ability to display 7 different colors Powered by an ESP32 microcontroller with built-in WiFi and Bluetooth 4.0 (BLE) Consumes extremely small amount of power, whether powered by a lithium battery or USB, in deep sleep mode it consumes only 18 µA, so it will run on one battery for years, and there is also a battery charger located on the board! MicroSD card reader from which Inkplate 6COLOR can extract images to display on its display Additional GPIO lines available, easyC/Qwiic compatibility and I²C and SPI support Arduino library ready (100% compatible with Adafruit GFX) and micropython that enable display of text, images and geometric shapes Dimensions: 131.5 x 105.5 x 10 mm Downloads Arduino library Inkplate documentation Getting started with Inkplate

    3 in stock

    € 114,95

    Members € 103,46

  • "MaTouch ESP32-S3 Parallel TFT 7\" Touch Display (1024x600)"

    Makerfabs "MaTouch ESP32-S3 Parallel TFT 7\" Touch Display (1024x600)"

    This ESP32 S3 7-inch IPS 5-point capacitive touch display with an ultra-high resolution of 1024 x 600 pixels is ideal for IoT applications. It is ideal for applications such as home automation. An integrated SD card enables recording/playback of stored data. There are also two Mabee/Grove connectors to connect various sensors to this board to create personal prototype projects in no time. Specifications Controller: ESP32-S3-WROOM-1, PCB antenna, 16 MB Flash, 8 MB PSRAM, ESP32-S3-WROOM-1-N16R8 Wireless: Wifi & Bluetooth 5.0 LCD: 7-inch High Lightness IPS FPS: >30 Resolution: 1024 x 600 LCD interface: RGB 565 Touch panel: Capacitive 5-point touch Touch panel driver: GT911 USB: Dual USB-C (one for USB-to-UART and one for native USB) UART to UART chip: CP2104 Power supply: USB-C 5.0 V (4.0 V~5.25 V) Button: Flash button and reset button Mabee interface: 1x I²C, 1x GPIO MicroSD: Yes Arduino support: Yes Type-C Power Delivery: Not supported Operation temperature: −40 to +85°C Downloads Wiki GitHub ESP32-S3 Datasheet Screen touch coordinates calibration

    € 59,95

    Members € 53,96

Login

Forgot password?

Don't have an account yet?
Create an account