Comparison Websites DE

170 products


  • Great Scott Gadgets YARD Stick One – Sub-1 GHz Wireless Test Tool

    Great Scott Gadgets Great Scott Gadgets YARD Stick One - Sub-1 GHz Wireless Test Tool

    YARD Stick One (Yet Another Radio Dongle) is a sub-1 GHz wireless transceiver IC on a USB dongle. It is based on the Texas Instruments CC1111. YARD Stick One can transmit or receive digital wireless signals at frequencies below 1 GHz. It uses the same radio circuit as the popular IM-Me. The radio functions that are possible by customizing IM-Me firmware are now at your fingertips when you attach YARD Stick One to a computer via USB. Features Half-duplex transmit and receive Official operating frequencies: 300-348 MHz, 391-464 MHz, and 782-928 MHz Unofficial operating frequencies: 281-361 MHz, 378-481 MHz, and 749-962 MHz Modulations: ASK, OOK, GFSK, 2-FSK, 4-FSK, MSK Data rates up to 500 kbps Full-Speed USB 2.0 SMA female antenna connector (50 ohms) Software-controlled antenna port power (max 50 mA at 3.3 V) Low pass filter for elimination of harmonics when operating in the 800 and 900 MHz bands GoodFET-compatible expansion and programming header GIMME-compatible programming test points Open source Downloads Documentation GitHub

    € 99,95

    Members € 89,96

  • Great Scott Gadgets Opera Cake – Antenneschakelaar voor HackRF One

    Great Scott Gadgets Great Scott Gadgets Opera Cake – Antenna Switch for HackRF One

    Opera Cake is an antenna switching add-on board for HackRF One that is configured with command-line software either manually, or for automated port switching based on frequency or time. It has two primary ports, each connected to any of eight secondary ports, and is optimized for use as a pair of 1x4 switches or as a single 1x8 switch. Its recommended frequency range is 1 MHz to 4 GHz. When HackRF One is used to transmit, Opera Cake can automatically route its output to the appropriate transmit antennas, as well as any external filters, amplifiers, etc. No changes are needed to the existing SDR software, but full control from the host is available. Opera Cake also enhances the HackRF One’s use as a spectrum analyzer across its entire operating frequency range of 1 MHz to 4 GHz. Antenna switching works with the existing hackrf_sweep feature, which can sweep the whole tuning range in less than a second. Automatic switching mid-sweep enables the use of multiple antennas when sweeping a wide frequency range. Downloads Documentation GitHub

    € 199,95

    Members € 179,96

  •  -12% Great Scott Gadgets HackRF One Software Defined Radio (1 MHz tot 6 GHz)

    Great Scott Gadgets Great Scott Gadgets HackRF One Software Defined Radio (1 MHz to 6 GHz)

    5 reviews

    HackRF One is a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1 MHz to 6 GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation. Specifications 1 MHz to 6 GHz operating frequency Half-duplex transceiver Up to 20 million samples per second 8-bit quadrature samples (8-bit I and 8-bit Q) Compatible with GNU Radio, SDR and more Software-configurable RX and TX gain and baseband filter Software-controlled antenna port power (50 mA at 3.3 V) SMA female antenna connector SMA female clock input and output for synchronization Convenient buttons for programming Internal pin headers for expansion Hi-Speed USB 2.0 USB-powered Open source hardware HackRF One is test equipment for RF systems. It has not been tested for compliance with regulations governing transmission of radio signals. You are responsible for using your HackRF One legally. Included 1x HackRF One 1x Injection molded plastic enclosure 1x micro-USB cable Note: An antenna is not included. ANT500 is recommended as a starter antenna for HackRF One. Downloads Documentation GitHub Source code and hardware design files

    € 339,00€ 299,00

    Members identical

  •  -17% Great Scott Gadgets HackRF One SDR + Opera Cake Antenneschakelaar (Bundel)

    Great Scott Gadgets Great Scott Gadgets HackRF One SDR + Opera Cake Antenna Switch (Bundle)

    HackRF One Software Defined Radio HackRF One is a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1 MHz to 6 GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation. Specifications 1 MHz to 6 GHz operating frequency Half-duplex transceiver Up to 20 million samples per second 8-bit quadrature samples (8-bit I and 8-bit Q) Compatible with GNU Radio, SDR and more Software-configurable RX and TX gain and baseband filter Software-controlled antenna port power (50 mA at 3.3 V) SMA female antenna connector SMA female clock input and output for synchronization Convenient buttons for programming Internal pin headers for expansion Hi-Speed USB 2.0 USB-powered Open source hardware HackRF One is test equipment for RF systems. It has not been tested for compliance with regulations governing transmission of radio signals. You are responsible for using your HackRF One legally. Note: An antenna is not included. ANT500 is recommended as a starter antenna for HackRF One. Documentation/Software Documentation GitHub Source code and hardware design files Opera Cake Antenna Switch for HackRF One Opera Cake is an antenna switching add-on board for HackRF One that is configured with command-line software either manually, or for automated port switching based on frequency or time. It has two primary ports, each connected to any of eight secondary ports, and is optimized for use as a pair of 1x4 switches or as a single 1x8 switch. Its recommended frequency range is 1 MHz to 4 GHz. When HackRF One is used to transmit, Opera Cake can automatically route its output to the appropriate transmit antennas, as well as any external filters, amplifiers, etc. No changes are needed to the existing SDR software, but full control from the host is available. Opera Cake also enhances the HackRF One’s use as a spectrum analyzer across its entire operating frequency range of 1 MHz to 4 GHz. Antenna switching works with the existing hackrf_sweep feature, which can sweep the whole tuning range in less than a second. Automatic switching mid-sweep enables the use of multiple antennas when sweeping a wide frequency range. Downloads Documentation GitHub This bundle contains: 1x HackRF One SDR 1x Injection molded plastic enclosure 1x micro-USB cable 1x Opera Cake Antenna Switch

    € 538,95€ 449,00

    Members identical

  • Great Scott Gadgets GreatFET One Universal USB

    Great Scott Gadgets Great Scott Gadgets GreatFET One Universal USB

    GreatFET One is a hardware hacker’s best friend. With an extensible, open source design, two USB ports, and 100 expansion pins, GreatFET One is your essential gadget for hacking, making, and reverse engineering. By adding expansion boards called neighbors, you can turn GreatFET One into a USB peripheral that does almost anything.Whether you need an interface to an external chip, a logic analyzer, a debugger, or just a whole lot of pins to bit-bang, the versatile GreatFET One is the tool for you. Hi-Speed USB and a Python API allow GreatFET One to become your custom USB interface to the physical world.Features Serial protocols: SPI, I²C, UART, and JTAG Programmable digital I/O Analog I/O (ADC/DAC) Logic analysis Debugging Data acquisition Four LEDs Versatile USB functions High-throughput hardware-assisted streaming serial engine Downloads Documentation GitHub

    € 99,95

    Members € 89,96

  • Google Coral USB Accelerator

    Google Google Coral USB Accelerator

    The Coral USB Accelerator adds an Edge TPU coprocessor to your system, enabling high-speed machine learning inferencing on a wide range of systems, simply by connecting it to a USB port. Features Supported host OS: Debian Linux, macOS, Windows 10 Compatible with Raspberry Pi boards Supported Framework: TensorFlow Lite Performs high-speed ML inferencing The on-board Edge TPU coprocessor is capable of performing 4 trillion operations (tera-operations) per second (TOPS), using 0.5 watts for each TOPS (2 TOPS per watt). For example, it can execute state-of-the-art mobile vision models such as MobileNet v2 at almost 400 FPS, in a power-efficient manner. Supports all major platforms Connects via USB to any system running Debian Linux (including Raspberry Pi), macOS, or Windows 10. Supports TensorFlow Lite No need to build models from the ground up. TensorFlow Lite models can be compiled to run on the Edge TPU. Supports AutoML Vision Edge Easily build and deploy fast, high-accuracy custom image classification models to your device with AutoML Vision Edge. Specifications ML accelerator Google Edge TPU coprocessor:4 TOPS (int8); 2 TOPS per watt Connector USB 3.0 Type-C (data/power) Dimensions 65 x 30 mm Downloads/Documentation Datasheet Get started with the USB Accelerator Model compatibility on the Edge TPU Edge TPU inferencing overview Run multiple models with multiple Edge TPUs Pipeline a model with multiple Edge TPUs PyCoral API (Python) Libcoral API (C++) Libedgetpu API (C++) Edge TPU compiler Pre-compiled models All software downloads

    € 89,95

    Members € 80,96

  •  -36% Get Started with the SensorTile.box Bundle

    Elektor Bundles Get Started with the SensorTile.box Bundle

    ‘SensorTile.box’ is a portable multi-sensor circuit board housed in a plastic box and developed by STMicroelectronics. It is equipped with a high-performance 32-bit ARM Cortex-M4 processor with DSP and FPU, and various sensor modules, such as accelerometer, gyroscope, temperature sensor, humidity sensor, atmospheric pressure sensor, microphone, and so on. SensorTile.box is ready to use with wireless IoT and Bluetooth connectivity that can easily be used with an iOS or Android compatible smartphone, regardless of the level of expertise of the users. SensorTile.box is shipped with a long-life battery and all the user has to do is connect the battery to the circuit to start using the box. Sensors Included Temperature 3-axis Accelerometer 3-axis Magnetometer 3-axis Acceleration & Gyro (6-axis Inertia) Humidity Altimeter/Pressure Microphone Peripherals Included Bluetooth Li-Ion Charger DC-DC Converter 500 mAh Li-Ion Battery

    € 69,95€ 44,95

    Members identical

  •  -47% Get Started with the NXP i.MX RT1010 Development Bundle

    Elektor Bundles Get Started with the NXP i.MX RT1010 Development Bundle

    Develop Arm Cortex-M7 powered Audio, DSP and Motor Control Projects At the heart of NXP Semiconductors‘ MIMXRT1010 Development Kit is the i.MX RT1010 Crossover MCU sporting an Arm Cortex-M7 core truly capable of running power- and memory hungry DSP applications. The popular MCUXpresso IDE is key to creating software for the development kit, while a powerful SDK is provided to reduce program development time and effort. The dev kit offers great connectivity through its audio CODECs, 4-way headphone jack, external speaker connection, microphone, and Arduino interface. Conveniently, several on-board debug probes are supplied with the kit allowing you to debug your programs by talking directly to the MCU. Helped by the debugger, you can single-step through a program, insert breakpoints, view and modify variables, and so on. Using the MCUXpresso IDE and the SDK, many working and tested projects are developed in the book based on parts, modules, and technologies, including: LED and LCDs ADC I²C projects SPI projects UART projects Motor Control Audio and Digital Audio Processing (DSP) This bundle contains: Elektor Book: Get Started with the NXP i.MX RT1010 Development Kit (normal price: €34.95) NXP i.MX RT1010 Kit Development Kit (normal price: €49.95)

    € 84,95€ 44,95

    Members identical

  •  -17% Get Started with the MAX78000FTHR Bundle

    Elektor Bundles Get Started with the MAX78000FTHR Bundle

    2 reviews

    The MAX78000FTHR from Maxim Integrated is a small development board based on the MAX78000 MCU. The main usage of this board is in artificial intelligence applications (AI) which generally require large amounts of processing power and memory. It marries an Arm Cortex-M4 processor with a floating-point unit (FPU), convolutional neural network (CNN) accelerator, and RISC-V core into a single device. It is designed for ultra-low power consumption, making it ideal for many portable AI-based applications. This book is project-based and aims to teach the basic features of the MAX78000FTHR. It demonstrates how it can be used in various classical and AI-based projects. Each project is described in detail and complete program listings are provided. Readers should be able to use the projects as they are, or modify them to suit their applications. This book covers the following features of the MAX78000FTHR microcontroller development board: Onboard LEDs and buttons External LEDs and buttons Using analog-to-digital converters I²C projects SPI projects UART projects External interrupts and timer interrupts Using the onboard microphone Using the onboard camera Convolutional Neural Network

    € 59,95€ 49,95

    Members identical

  •  -17% FNIRSI SWM-10 Portable Battery Spot Welder

    FNIRSI FNIRSI SWM-10 Portable Battery Spot Welder

    Pre-order

    The FNIRSI SWM-10 is an efficient, practical and easy-to-carry handheld spot welder with a built-in 5000 mAh lithium battery that also functions as a power bank. The double-pulse spot welding technology makes the welding more stable and firm. Features 5000 mAh lithium battery for long battery life Fast charging power bank High-resolution 1.8" TFT LCD color screen Built-in intelligent temperature control sensor, over temperature, low voltage and short circuit protection Customized settings for preheat, pulse, interval and number of connection points make welding more stable and safer Can weld nickel sheets, iron sheets, stainless steel sheets, etc. The maximum welding thickness is 0.25 mm, and the welding current is 1200 A. Specifications Capacity 5000 mAh Charge 5 V/2.1 A Discharge 5 V/2.1 A Welding materials Nickel sheet, iron sheet, stainless steelsheet, aluminum sheet Welding thickness 0.1-0.25 mm Maximum welding current 1200 A Gear 4 combination gear adjustment Dimensions 155 x 82 x 28 mm Included 1x FNIRSI SWM-10 spot welder 2x Spot welding pens 1x Nickel sheet 2x Spare needles 1x USB cable 1x Manual Downloads Manual

    Pre-order

    € 59,95€ 49,95

    Members identical

  •  -22% FNIRSI SG-003A Signal Generator

    FNIRSI FNIRSI SG-003A Signal Generator

    1 review

    The FNIRSI SG-003A Multi-Functional Signal Generator a.k.a. Process Meter/Calibrator is a high-precision voltage/current generator and meter. The SG-003A provides highly accurate reference voltages or currents for testing and calibrating other measurement instruments like multimeters and oscilloscopes. Besides voltages and currents, the SG-003A also generates rectangular pulse signals with precisely programmable frequencies and duty cycles. Its converter mode turns the SG-003A into a precision voltage-controlled current source, or current-controlled voltage source, and even a voltage- or current-controlled frequency generator. The SG-003A is a great tool for checking your multimeter’s accuracy and precision, and for testing e.g. LEDs. Features Accuracy (voltage/current) 0.1% ±0.005 Resolution (current) 0.01 mA Frequency 0-10 kHz Resolution 5 digits Output power 24 V Display 2.4' TFT LCD (320 x 240) Dimensions 92 x 72 x 30 mm Weight 165 g Specifications Signal Range Precision Resolution Max load External power supply Active current output 0~24 mA ±(0.1% + 0.005) 0.01 mA 750 Ω Passive current output (XMT) 0~24 mA ±(0.1% + 0.005) 0.01 mA 0~30 V Voltage output 0~24 V ±(0.1% + 0.005) 0.01 V 24 V loop 0~24 mA ±(0.1% + 0.005) 0.01 mA Frequency output 0~9999 Hz ±2% 5 digits Current input 0~24 mA ±(0.1% + 0.005) 0.01 mA Voltage input 0~30 V ±(0.1% + 0.005) 0.01 V Included 1x FNIRSI SG-003A signal generator 4x Test clips 1x USB charger 1x USB-C cable 1x Manual Downloads Manual

    € 89,95€ 69,95

    Members identical

  • FNIRSI IR40 Laser Rangefinder (40 m)

    FNIRSI FNIRSI IR40 Laser Rangefinder (40 m)

    The FNIRSI IR40 is a compact, high-precision and fast distance measuring device with Bluetooth integration, rechargeable battery, USB-C charging port and app connection. Features It features a high precision of ±2 mm, up to 40 m measurement range, and an 8 cm skin-friendly feeling. With an intelligent algorithm, it will make the distance measurement in an instant. Has versatile functions, including single measurement, multiple measurements, area measurement, volume measurement, Pythagorean, second Pythagorean, front and rea reference, and unit switching. FNIRSI IR40 laser rangefinder is equipped with a ROHM acceleration sensor, realizes auto flip. Built-in 400 mAh battery, it can be charged with a USB-C charging port quickly. When fully charged, it can offer up to 3000 times of continuous measurement. It supports Android & iOS systems, and Link APP to realize functions such as data synchronization/remarks, length/area/volume calculation, floor plan drawing, real-time recording, etc. Specifications Measurement range 0.05~40 m Measurement accuracy ±2 mm Laser type 620-670 nm Measurement time 0.1~3s Resolution 1 mm Units m/ft/in Dimensions 79 x 34.5 x 19 mm Included FNIRSI IR40 Rangefinder USB cable Manual Downloads Manual Android App iOS App

    € 34,95

    Members € 31,46

  • FNIRSI HS-01 Smart Soldering Iron (incl. 6 Soldering Tips)

    FNIRSI FNIRSI HS-01 Smart Soldering Iron (incl. 6 Soldering Tips)

    The perfect tool for quick repairs The HS-01 is a powerful, adjustable smart soldering iron with a built-in 0.87-inch OLED display that quickly reaches temperatures between 80-420°C (180-780°F). The display shows all important information, including the status of the temperature level, the set temperature, the supply voltage and the power percentage. You can set the input voltage from 9-20 V directly in the menu according to your needs. The integrated sleep mode automatically turns off the iron after 30 minutes. Features 96 W input (DC) 65 W PD power OLED display Constant temperature & fast heating CNC metal integral molding Smart safety anti-scald Mini pocket size Ergonomic design Aluminum material Left/right hand switch Efficient heat radiation Inductive sleep Color: Black Specifications Power 65 W Screen 0.87' OLED Operating voltage 9-20 VDC Power supply USB-C Temperature range 80-420°C (180-780°F) Fast charging protocol PD trigger Dimensions 184 x 20 x 20 mm (7.24 x 0.79 x 0.79') Weight 56 g Power Selection Operating voltage 20 V 15 V 12 V 9 V Operating current ≥3.25 A ≥2.5 A ≥2 A ≥1.5 A Power 65 W 37.5 W 24 W 13.5 W Tin melting time 8s 12s 17s 30s Included 1x FNRISI HS-01 smart soldering iron 6x Soldering iron tips (HS01-BC2, HS01-KR, HS01-K65, HS01-B2, HS01-ILS, HS01-BC3) 1x DC to USB-C power cable 1x Mini soldering iron stand 1x Manual Required Power adapter USB-C cable Downloads User Manual

    € 74,95

    Members € 67,46

  • FNIRSI FNB58 USB Tester with Bluetooth (Voltage & Current Meter)

    FNIRSI FNIRSI FNB58 USB Tester with Bluetooth (Voltage & Current Meter)

    The FNB58 USB tester (with Bluetooth) is a comprehensive and very accurate USB voltage and current meter. It features a 2.0-inch full-color HD TFT display, built-in USB-A, micro USB and USB-C interface. With this device you can measure the power supply or power consumption of products or the charging power of cell phones and power supplies. You can also determine the fast charging protocol of chargers. Features USB and Type-C interface 2.0" HD display Data at a glance Wide compatibility Ultra-precise data detection Play with fast charging technology Automatic protocol detection (PD2.0, 3.0, 3.1, PPS, QC2.0, 3.0, FCP, SCP, AFC, PE, DASH VOOC, SuperVOOC and more) Simple user interface, easy to operate 4 function curve displays (real-time voltage and current curve, offline curve recording, D+/D- voltage curve, high-speed power supply ripple measurement) Cable detection 10 groups of energy recording battery capacity calculation PC connectivity for data logging and firmware updates Bluetooth app for Android devices Specifications Voltage range 4-28 V Current range 0-7 A Power range 0-120 W Load equivalent internal resistance 0-9999.9 Ω D+/D- voltage 0-3.3 V Capacity 0-9999.99 Ah Power consumption 0-9999.99 Wh Cable resistance 0-9999.9 Ω Interfaces micro USB, USB-A, USB-C Dimensions 42 x 13 x 82 mm Downloads User manual Firmware

    € 59,95

    Members € 53,96

  • FNIRSI DSO152 Oscilloscope (200 kHz)

    FNIRSI FNIRSI DSO152 Oscilloscope (200 kHz)

    1 review

    The FNIRSI DSO152 is an extremely practical and cost-effective handheld oscilloscope with a real-time sampling rate of 2.5 MSa/s, a bandwidth of 200 kHz and complete trigger functions (single, normal and automatic). It can be used for both periodic analog signals and non-periodic digital signals and can measure voltages up to ±400 V. Equipped with an efficient one-key AUTO, it can display the measured waveform without cumbersome adjustments. It is equipped with a high-resolution 2.8-inch LCD screen with a resolution of 320x240 pixels and a built-in 1000 mAh high-quality lithium battery for up to 4 hours of operation. Specifications Sampling rate 2.5 MSa/s Bandwidth 200 kHz Vertical sensitivity 10 mV/DIV - 20 V/DIV (Progress according to the 1-2-5 way) Time base range 10µS/DIV - 50s/DIV (Progress according to the 1-2-5 way) Voltage range X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V) Trigger method Auto/Normal/Single Coupling method AC/DC Display 2.8' (320x240 pixels) USB charging 5 V/1 A Lithium battery capacity 1000 mAh Square wave calibration Frequency: 1K, Duty cycle: 50% Dimensions 99 x 68.3 x 19.5 mm Weight 100 g Included FNIRSI DSO152 oscilloscope Alligator clip probe USB cable Lanyard Manual Downloads Manual

    € 39,95

    Members € 35,96

  •  -20% FNIRSI DSO-TC3 (3-in-1) Oscilloscope, Component Tester & Signal Generator

    FNIRSI FNIRSI DSO-TC3 (3-in-1) Oscilloscope, Component Tester & Signal Generator

    DSO-TC3 combines a digital oscilloscope, electronic component tester, signal generator, continuity test, voltage test, temperature and humidity measurement, infrared decoding and other functions are skillfully integrated. It is equipped with a 2.4' color TFT display and a built-in rechargeable lithium battery for mobile use. Specifications (Oscilloscope) The oscilloscope has a real-time sampling rate of 10 MSa/s and a bandwidth of 500 kHz. With complete trigger function (single, normal, automatic), no matter if you’re using periodic analog signals or non-periodic digital signals. Maximum measured voltage signal is 400 V. Equipped with efficient AUTO, the measured waveform can be displayed without cumbersome adjustments. Real-time sample rate 10 MSa/s Bandwidth 500 khz Input resistance 1 MΩ Coupling method AC/DC Test voltage range 400 V Vertical Sensitivity (x1) 10 mV-10 V Horizontal time base range 1us-10s Trigger mode Auto/Normal/Single Trigger type Rising edge/Falling edge Waveform Freeze Yes Automatic measurement Yes Specifications (Component Tester) The instrument can automatically identify and measure various transistors, including NPN and PNP triodes, N-channel and P-channel mosfet, junction mosfet, diodes, dual diodes, thyristors, and resistors, inductors, capacitors and other passive components. Automatic detection of pin definition. Automatically analyze NEC protocol infrared code. Other functional modes: Including circuit continuity test, 0-40 V input voltage measurement, PWM output, 0-32 V regulated diode measurement, DS18B20 temperature sensor measurement, DHT11 temperature and humidity sensor measurement, etc. Specifications (Signal Generator) The signal generator has a total of 6 waveforms to choose from, with adjustable frequency and amplitude. Sine wave 1-100 KHz/0-3.3 V/50% Square wave 1-100 KHz/3.3 V/50% Pulse wave 1-100 KHz/3.3 V/0-100% Triangle wave 1-100 KHz/0-3.3 V/50% Ramp 1-100 KHz/0-3.3 V/0-100% DC 0-3.3 V Included 1x DSO-TC3 1x P6100 Oscilloscope Probe (100 MHz) 3x Test Hooks 1x Adapter 1x USB-C Cable 1x Original Manual by FNIRSI (English, Chinese, Russian, Portuguese) 1x Elektor Manual (English, French, German, Italian, Dutch) Downloads Original Manual Firmware v0.3

    € 74,95€ 59,95

    Members identical

  •  -16% FNIRSI DPOX180H (2-in-1) 2-ch Phosphor Oscilloscope (180 MHz) & Signal Generator

    FNIRSI FNIRSI DPOX180H (2-in-1) 2-ch Phosphor Oscilloscope (180 MHz) & Signal Generator

    2 reviews

    The FNIRSI DPOX180H is a cost-effective handheld dual-channel digital phosphor oscilloscope and signal generator. The oscilloscope has a real-time sampling rate of 500 MS/s and an analog bandwidth of 180 MHz. The measurement results are displayed on the high-contrast 2.8-inch IPS full-view LCD screen with digital fluorescence technology. Features 2-ch handheld oscilloscope & DDS signal generator 180 MHz bandwidth 500 MS/s sampling rate 20 MHz signal generator Innovative digital trigger system Cursor measurement function 5 mV sensitivity 50000 wfm/s waveform refresh rate 2.8" IPS full-vision high-definition display Built-in 4.2 V/3000 mAh lithium battery Automatic shutdown setting High-voltage anti-burning protection Specifications Nummer of channels 2 Analog bandwidth 180 MHz Maximum sampling rate 500 MS/s Input coupling DC/AC Rise time 2.5s Storage depth 120 Kpts Input impedance 1 MQ-18 PF Vertical sensitivity 5 mV-10 V (1X) Time base range 5 nS~50 S DC accuracy ±2% Time accuracy +0.01% Trigger detection Digital trigger Trigger mode Auto/Single/Normal Trigger edge Rising/Falling Measurement range 40 mV~80 V (1X) Screenshot storage 90 Capture signal 500 Screen size 2.8 inch Screen resolution 320 x 240 Display technology IPS full view Expansion interface USB transmission interface Auto power off 5 minutes - 2 hours Firmware upgrade Supported iso image upgrade Charging requirements 5 V/2 A Battery capacity 3000 mAh Standby time 3.5 hours at full charge Signal Generator 14 standard function signals Waveform storage 250 groups Parameter measurement 12 kinds Dimensions 135 x 90 x 40 mm Digital Phosphor Oscilloscope FNIRSI DPOX180H Oscilloscope uses the latest digital phosphor technology to overcome the traditional oscilloscope due to noise caused by the waveform burr feeling. Color temperature display function can more clearly see the distribution of the signal, probability characteristics and the rise and fall time of the step signal fast and slow. X-Y mode with digital phosphor technology for comparison of amplitude, frequency and phase of two groups of signals. DDS Function Signal Generator Built-in 20 MHz DDS function signal generator, with 14 kinds of standard function signals, output amplitude fixed at 1 VPP, sine wave frequency of 20 MHz, other waveform frequency of 10 MHz, adjustable frequency step of 1 Hz. Contains the original chopping technology, intercept part of the oscilloscope measurement of complex signals as the output signal of the signal generator, than the traditional signal generator hand-drawn signal more objective and realistic. Included 1x FNIRSI DPOX180H phosphor oscilloscope 2x Probes (200 MHz) 1x USB power supply 1x USB cable 1x Manual Downloads Manual Firmware V40

    € 159,95€ 134,95

    Members identical

  • FNIRSI DMT-99 Smart Multimeter

    FNIRSI FNIRSI DMT-99 Smart Multimeter

    The FNIRSI DMT-99 is an intelligent digital multimeter with 10000 counts, which offers a high measuring range and high resolution. It can accurately measure AC/DC voltage, AC/DC current, 10 A current and can also be used to test conductivity, capacitance, frequency, duty cycle, resistance, diode, temperature, NCV, live wire detection, etc. It is suitable for various electronic maintenance fields such as mechanical engineering, laboratories, automobiles and home appliances. It is equipped with a 1500 mAh lithium battery and a 2.4' TFT full-color display with a resolution of 240 x 320 pixels. Specifications Function Range Accuracy DC voltage 9.999 V/99.99 V/999.9 V ±(0.5%+3) AC voltage 9.999 V/99.99 V/750.0 V ±(1%+3) DC current 9999 uA/99.99 mA/999.9 mA/9.999 A ±(1.2%+3) AC current 9999 uA/99.99 mA/999.9 mA/9.999 A ±(1.5%+3) Resistance 9.999 MΩ/999.9 KΩ/99.99 KΩ/9.999 KΩ/999.9 Ω ±(1.5%+3) 99.99 MΩ ±(1.5%+3) Capacitance 999.9 µF/99.99 µF/9.999 µF/999.9 nF/99.99 nF/9.999 nF ±(2.0%+3) 9.999 mF/99.99 mF ±(5.0%+3) Frequency 9.999 MHz/999.9 KHz/9999 KHz/9.999 KHz/999.99 Hz/99.99 Hz/9.999 Hz ±(0.1%+3) Temperature -55~1300°C (-64~2372°F) ±(2.5%+3) Diode Yes Continuity test Yes NVC Yes Live wire detection Yes Max counts 10000 counts Battery capacity 1500 mAh Dimensions 155 x 80 x 36 mm Weight 191 g Included 1x FNIRSI DMT-99 multimeter 2x Test pens 1x USB-C charging cable 1x Manual

    € 44,95

    Members € 40,46

  •  -21% FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope (10 MHz) + Multimeter + Signal Generator

    FNIRSI FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope (10 MHz) + Multimeter + Signal Generator

    2 reviews

    Pre-order

    The FNIRSI 2C23T is a fully functional, highly practical 3-in-1 dual channel digital oscilloscope with a high resolution 2.8-inch LCD display (320 x 240 pixels) designed for the maintenance and development industry. This device is equipped with 3 main functions: oscilloscope, multimeter and signal generator. The oscilloscope has an FPGA+MCU+ADC hardware architecture with a sampling rate of 50 MS/s, an analog bandwidth of 10 MHz and a built-in high-voltage protection module that supports the measurement of peak voltages of ±400 V maximum. The multimeter has a 4-digit 10000-point RMS value and supports AC/DC voltage and current measurements, as well as capacitance, resistance, diode, on/off and other measurement functions. Equipped with a built-in DDS function signal generator, it can output 7 kinds of function signals, with a maximum output of 2 MHz for all signals and a step of 1 Hz; the output frequency, amplitude and duty cycle are adjustable. The built-in 3000 mAh rechargeable lithium battery achieves a standby time of up to 6 hours. Features 2-ch oscilloscope 10 MHz bandwidth 50 MS/s real-time sampling rate 7 signal waveforms 10000 counts 2.8' HD color display (320 x 240 pixels) Dimensions: 167 x 89 x 35 mm Weight: 300 g Specifications Oscilloscope Dual channel, 2x 10 MHz bandwidth, 50 MS/s real-time sampling rate Maximum measured voltage: ±400 V FPGA+ADC+MCU high-performance hardware architecture, capturing waveform details without loss Equipped with complete triggering functions (auto, single, normal) Equipped with efficient automatic adjustment, the measured waveform can be displayed without complicated adjustment Save waveform screenshots, supports exporting images to a computer, facilitate secondary waveform analysis Multimeter 4-bit integer 9999 counting True RMS measurement Identification of voltage, current, capacitance, resistance, diode, on/off, and zero live wire Maximum input voltage: AC 750 V, DC 1000 V Automatic range, intelligent anti burning Data retention, color screen digital display Signal Generator 7 signal waveforms: sine wave, square wave, triangular wave, full wave, half wave, noise wave, DC Output frequency: 1 Hz-2 MHz Output amplituade: 0.1-3.3 V Output duty cycle: 0-100% Included 1x FNIRSI 2C23T (3-in-1) 2-ch Oscilloscope 1x P6100 oscilloscope probes (10X) 1x Multimeter probe 1x Crocodile clip probe 1x USB-C charging cable 1x Original Manual by FNIRSI (English, German, Spanish, Portuguese, Russian, Chinese) 1x Elektor Manual (English, French, German, Dutch) Downloads Manual Firmware V2.0.2

    Pre-order

    € 94,95€ 74,95

    Members identical

  • FNIRSI 1014D (2-in-1) 2-ch Oscilloscope (100 MHz) & Signal Generator

    FNIRSI FNIRSI 1014D (2-in-1) 2-ch Oscilloscope (100 MHz) & Signal Generator

    1 review

    The FNIRSI 1014D is a 2-in-1 oscilloscope and signal generator with comprehensive functions and high practicality. It is a cost-effective 2-channel desktop oscilloscope for the maintenance industry and R&D industry. The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. The built-in DDS signal generator supports 12 types of function signals. Specifications Channels 2 Display size 7 inch LCD LCD resolution 800 x 480 Bandwidth 100 MHz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50s ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X : 40V, 10X : 400V Cursor Position XY, Trigger Y Waveform storage 1000 pictures + 1000 waveforms Roll mode Yes One-button AUTO Yes Waveform manager Yes Capture output Yes Voltage accuracy ±5% Frequency precision ±0.01% high precision Parameter 12 kinds in total Generator 14 kinds in total Extension USB export Power supply 5 V/2 A, 3 A, 4 A Dimensions 310 x 145 x 70 mm Included 1x FNIRSI 1014D Oscilloscope 2x Oscilloscope probes (100 MHz) 1x USB charger 1x Manual Downloads User Guide

    € 169,95

    Members € 152,96

  • FNIRSI 1013D 2-ch Tablet Oscilloscope (100 MHz)

    FNIRSI FNIRSI 1013D 2-ch Tablet Oscilloscope (100 MHz)

    1 review

    The FNIRSI 1013D is a fully featured 2-channel tablet oscilloscope with a high-resolution 7-inch LCD screen (800 x 480 pixels). The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. With full trigger functions (single/normal/automatic), it can be used for periodic analog signals or non-periodic digital signals. The built-in high-voltage protection module can withstand a continuous voltage of up to 400 V. Features Intelligent anti-burn,1X can withstand up to 400 V withstand voltage. 100 MHz analog bandwidth @ 1 GSa/s sampling rate (1X = 5 MHz,10X = 100 MHz). Fully fit 7-inch 800 x 480 resolution color TFT LCD display with bright colors and high contrast. Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation. High measurement voltage range, 1X can measure 0~40 V, 10X can measure 0~400 V,100X can measure 0~4000 V. Up to 12 parameters measurement: VPP, VP, Vmax, Vmin, Vavg, Vrms, Frequent, Duty+, Duty-, Time+, Time−, Period. Cursor measurement function, it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic). At any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO. One-button waveform storage and screenshot. Built-in 1 GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal. Built-in 6000 mAh rechargeable lithium battery, fully charged for 4 hours of continuous use at the highest screen brightness. Memory compression technology, waveform refresh screen does not flicker. Screen brightness adjustment. Background grid brightness adjustment. Applications Electronic DIY Appliance repair Car repair Equipment debug Scientific research Product development Specifications Channels 2 LCD size 7 inch LCD resolution 800 x 480 Display technology TFT Bandwidth 100 Mhz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50S ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X: 40 V, 10X: 400 V Cursor Position XY, Trigger Y Roll mode Yes One button AUTO Yes Waveform storage 1000 pictures + 1000 waveforms Waveform manager Yes Voltage accuracy ±2% Frequency precision ±0.01% high precision Parameter 12 kinds in total Battery 6000 mAh Lithium Standby 4 hours Extension USB export Power supply USB-C, 5 V @ 2 A/3 A/4 A Dimensions 184 x 124 x 50 mm Weight 650 g Included 1x FNIRSI 1013D 2-ch Tablet Oscilloscope 2x 100 MHz Probes (1X and 10X) 1x USB charger 1x USB cable 1x Manual Downloads Manual

    € 159,95

    Members € 143,96

  •  -19% Elektor Ultimate Sensor Kit

    Elektor Bundles Elektor Ultimate Sensor Kit

    This bundle consists of a high-quality sensor kit and comprehensive project book. It has been specifically developed to enable use of sensors across multiple open-source microcontroller platforms including Arduino, Raspberry Pi, and ESP32. The bundle contains a total of 40 different sensors that are applied in multiple projects. All described projects are supported with software examples. The projects provided in the kit include the following: Changing LED brightness RGB LEDs Creating rainbow colours Magic wand Silent door alarm Dark sensor with relay Secret key Magic light cup Decoding commercial IR handsets Controlling TV channels with IT sensors Target shooting detector Shock time duration measurement Ultrasonic reverse parking Toggle lights by clapping hands Playing melody Measuring magnetic field strength Joystick musical instrument Line tracking Displaying temperature Temperature ON/OFF control Mobile phone-based Wi-Fi projects Mobile phone-based Bluetooth projects Sending data to the Cloud

    € 79,95€ 64,95

    Members identical

  •  -21% Elektor ESP32 Smart Kit Bundel

    Elektor Bundles Elektor ESP32 Smart Kit Bundle

    2 reviews

    Experimenting with the ESP32 has never been easier! With the Elektor ESP32 Smart Kit Bundle, you'll learn programming with the ESP32 IoT Microcontroller using the Arduino IDE and MicroPython programming languages. The kit consists of the highly popular ESP32 DevKitC development board, breadboard, sensors, LEDs, LCD, etc. for use in experiments. The book provides basic and intermediate level projects. All projects have been tested and work. Block diagrams, circuit diagrams, and complete program listings of all projects are given with explanations. About the book: The main aim of this book is to teach the Arduino IDE and MicroPython programming languages in ESP32 based projects, using the highly popular ESP32 DevKitC development board. Many simple, basic, and intermediate level projects are provided in the book using the Arduino IDE with ESP32 DevKitC. All projects have been tested and work. Block diagrams, circuit diagrams, and complete program listings of all projects are given with explanations. In addition, several projects are provided for programming the ESP32 DevKitC using MicroPython. The kit consists of: 1x ESP32 DevKitC 8x LEDs (RED) 1x LED (GREEN) 2x push-button 8x 330 ohm resistors 1x Buzzer 1x RGB LED 1x TMP36 temperature sensor chip 1x DHT11 temperature and humidity chip 1x MCP23017 (DIL 28 package) 1x LDR 1x BC108 (or any other PNP) transistor 1x 7 segment LED 1x Small Microphone Module 1x I²C LCD 1x SG90 servo 1x 4x4 Keypad 8x Female-Male jumpers 4x Male-Male jumpers 1x Small breadboard

    € 69,95€ 54,95

    Members identical

  •  -18% Elektor Dual DC LISN (150 kHz – 200 MHz)

    Eurocircuits Elektor Dual DC LISN (150 kHz - 200 MHz)

    2 reviews

    Measuring conducted emission is the simplest and most affordable method of getting some indication of whether a design can meet EMI/EMC requirements. A Line Impedance Stabilization Network (LISN) is an indispensable part of an EMC pre-compliance test setup. In cooperation with Würth Elektronik, Elektor has developed a 5 µH, 50 Ω Dual DC LISN that supports voltages up to 60 V and currents up to 10 A. The instrument measures RF interferences on both channels (the power supply) by means of 5-μH blocking inductances. The internal 10-dB attenuation network – one in each channel – contains a 3rd-order high-pass filter with a cutoff frequency of 9 kHz to protect the input of instruments like a spectrum analyzer from potentially harmful DC voltages or low frequencies coming from the EUT (Equipment Under Test). Specifications RF path Channels 2 (with clamping diodes) Bandwidth 150 kHz – 200 MHz Inductance 5 μH || 50 Ω Internal attenuation 10 dB Connectors SMA DC path Max. current < 10 ADC Max. voltage < 60 VDC DC resistance < 2 x 70 mΩ PCB size 94.2 x 57.4 mm Connectors 4-mm banana Hammond enclosure Type 1590N Dimensions 121 x 66 x 40 mm Included 1x 4-layer PCB with all SMT parts fitted 1x pre-drilled enclosure with ready-printed front panel layout 5x gold-plated, insulated, 4-mm banana sockets, rated for 24 A, 1 kV 1x Hammond enclosure 1590N1, Aluminum (Die-Cast Alloy) More Info Project on Elektor Labs: Dual DC LISN for EMC pre-compliance testing Elektor 9-10/2021: EMC Pre-Compliance Test for Your DC-Powered Project (Part 1) Elektor 11-12/2021: EMC Pre-Compliance Test for Your DC-Powered Project (Part 2)

    € 139,95€ 114,95

    Members identical

Login

Forgot password?

Don't have an account yet?
Create an account