Search results for "oscilloscope analogique"
LabNation LabNation SmartScope USB Oscilloscope
Smartscope is the only scope in the world that runs on all major platforms: Windows, macOS, Linux, Android and iOS (with WiFi bridge). Connect the SmartScope to pretty much any device! Even more, you can get mobile with it: take the SmartScope on the road, thanks to the single-cable connectivity. Everything is going to be intuitive: pointing, pinching and swiping finally replaces the clunky interfaces of old scopes. With the SmartScope you develop your digital interfaces using the 100 MS/s logic analyzer. With this tool you can design any signal you want using Excel, then upload it to the built-in Arbitrary Waveform Generator (AWG). At the end capture the voltage at any point of your design at 100 million times each second. The Software for the support of Windows / macOS) / Linux / Android and Export formats (Excel .csv / Matlab .mat) are given. Features Channel sampled at 100 MHz/s each AC/DC coupling on analog inputs 100% silent 64 Mbit RAM: x10000 zoom Arbitrary Waveform Generator 8 digital inputs at 100 MS/s each 4 digital outputs at 100 MS/s each Externally power your scope in case your mobile can't supply the juice. Specifications Oscilloscope Bandwidth 30 MHz (-3 dB point) Sample rate 2x 100 MS/s Channels 2 Max pre-trigger position 16x full scale Max post-trigger position Full scale Max full voltage scale 10 V/div (±35 V input range) Min full voltage scale 20 mV/div Analog input range -35 V, +35 V Max input peak-to-peak 40 V Signal coupling AC / DC Precision 8 bit Input impedance 1 MΩ // 10 pF Waverforms 200 waveforms/s Data delay to host Sample depth Up to 4 million samples per channel External trigger Yes Logic Analyzer Input channels 8 Input impedance 100 kOhm // 2 pF to GND Sample rate 100 MS/s Logic level 1.8 V to 5.0 V Diode protection Bidirectional Input data buffer 4 million samples Waverforms 200 waveforms/s Data delay to host Protocol decoders I²C, SPI, UART, I²S integrated User extensible Wave Generator (Analog Output) Output channels 1 Data rate Up to 50 MS/s Output level 0-3.3 V (Opamp driven) Output buffer Up to 2048 samples Max slew rate 30 ns/V Step 13 mV Wave Generator (Digital Output) Channels 4 Data rate Up to 100 MS/s Output level 3.3 V or 5 V (selectable) Output buffer Up to 2048 samples Diode protected Yes Programmable Logic USB controller MicroChip PIC18F14K50 USB interface PicKit3 or USB flashable FPGA Xilinx Spartan 6 FPGA interface JTAG and USB flashable Size & Weight Dimensions (L x W x D) 4.33 x 2.52 x 0.95" (110 x 64 x 24.2 mm) Weight 158 g Case Aluminium Connectivity Device/Host mini USB included Record waveforms Store Matlab (.mat) or Excel (.csv) files through Dropbox Analog BNC 2 probes included Digital 8x 0.1" pitch, probes (included) Sync USB micro B-B Power USB micro B (optional) Included 1x SmartScope USB Oscilloscope 2x Analog probes 1x Digital probe cable 1x Mini-B USB cable Downloads User manual Software GitHub Wiki
€ 239,00€ 149,95
Members identical
JYE Tech JYE Tech DSO Coral 112A Oscilloscope
DSO Coral (112A) is an upgraded model of DSO112 with re-designed schematic and PCB. Due to the new design this oscilloscope becomes more accurate and reliable. As high as 2 mV/div sensitivity and ultra low background noise made the device particularly useful for measuring weak signals. Up to 24 presets with customizable titles allow setups be retrieved in seconds. While keeping all performance of DSO112 this new model brings in the following improvements: Maximum sensitivity was increased to 2 mV/div (older version is 5 mV/div) with lower background noises. Fixed the vertical position mismatch problem found in the older model. Save/recall up to 24 parameter presets. This allows quick setup for frequently performed measurements. Preset titles can be customized for easy remembering and identifying. Expanded and improved on-screen measurement displays which include frequency, Vmax, Vmin, Vavr, Vpp, and Vrms. Added external trigger feature. Provided a two-way serial control interface which can output data/measurements and receive commands. This will make the device suitable for integration to customer applications. Replaced out-dated miniUSB connector with more popular microUSB connector. Enclosure strength enhanced. CE certified Specifications Vertical Number of Channel: 1 Analog Bandwidth: 0 - 2MHz Sensitivity: 2 mV/Div - 20 V/Div Sensitivity error: <5% Resolution: 8-bit Input Impedance: 1M ohm Maximum Input voltage: 50 Vpk Coupling: DC, AC, GND Voltage measurement cursors available Auto-measurement of Vavr and Vpp Horizontal Max Real-time Sampling Rate: 5 Msps Timebase: 1 us/Div - 50 s/Div Record Length: 512 and 1024 variable Time measurement cursors available Trigger Trigger Modes: Auto, Normal, Single Trigger Types: Rising/falling edge Trigger Position: 1/8, 1/4, 1/2, 3/4, and 7/8 of buffer size Trigger Source: internal, external External trigger voltage range: 0 - 15 V Test Signal Generator 7 frequencies from 1 Hz to 1 MHz selectable. Amplitude 3.3 V fixed Other Features Save captured waveform to EEPROM and recall after power outage Save/recall up to 24 presets Serial data/control interface USB firmware upgrade Display 2.4' color TFT LCD with 320 x 240 resolution Power Supply 3.7 V Li-ion battery/USB Supply Current: 300 mA @ 3.7 V(LCD backlight ON). Built-in charger Physical Dimension: 80 x 70 x 18 mm Weight: 85 gram (not including cables) Included 1x DSO112A (Battery included) 1x Standard BNC probe 2x MCX-clip cables 1x USB cable Quick User Guide Downloads Quick User Guide (Rev. 02) User Manual (Rev. 02) Firmware
€ 79,95€ 59,95
Members identical
JYE Tech JYE Tech DSO068 Oscilloscope DIY Kit
This kit is particularly suitable for educational use. It uses through-hole components as much as possible. This eases off the requirement of assembly skills and at the same time allows deeper user involvement. It is a great tool for college students. Most importantly it brings in the freedom for users to test, modify, experiment, and even design their own projects. And this means more fun! More over, DSO 068 is not just a kit for training but also a practical tool for everyday use. Parameter setting is simply, straightforward, and quick. Mode switch and utilities are driven by menu. Absolutely no complicate navigation. It was designed on the base of DSO 062 kit and comprises many enhancements in hardware and firmware: Higher sensitivity (10 mV/div vs 100 mV/div) Wider analog bandwidth (3 MHz vs 1 MHz) Larger capture buffer (1024 points vs 256 points) Variable trigger position (1% - 100%) with indicator Test signal generator with variable frequency and amplitude USB connection Upload of captured raw data as CSV file (Example) Work as USB scope (with jyeLab) and data logger (8 channels, 10-bit resolution) Higher sensitivity (0.2 Vpp vs 3 Vpp) in built-in frequecy meter Battery/USB powered Fully enclosured Silicone pushbuttons and rotary encoder Major parts Main circuit board with pre-soldered ICs and a few SMD parts. Board is pre-tested and MCUs on board are pre-programmed. 128 x 64 graphic dot-matrix LCD module. Step-up voltage converter board (JYE116). It boosts battery voltage to 5 V from as low as 2 V. Voltage inverter board (JYE120). It generates -5 V from +5 V with current capacity up to 200 mA. On/Off switch board (JYE117). This is the power switch of instrument. [optional] Li-ion battery charger board (JYE118). It includes the USB/Battery power switch circuit. [optional] USB-Uart converter board (JYE119). This bridges the scope to USB host. [optional] Professional 20 MHz probe with selectable 1X/10X attenuation. Enclosure set including stand, switch caps, etc. All through-hole components, mechanical parts, accessories (battery not included) and Assembly Guide and User Manual. Source codes of student version firmware are also provided for downloading. They are simplified from full version to help users to understand how the oscilloscope works. The sampling rate of student version is limited to 500 Sa/s - 100 KSa/s with no other features. Important Notes Adequate soldering skills and troubleshooting skills to assemble the DSO138 kit are required. Each mainboard has been tested to ensure no short or open on MCU soldering. Each LCD board is also tested to verify soldering is good and display is functional. The other components are provided with good quality at our best knowledge. They are not tested.
€ 79,95
Members € 71,96
PeakTech PeakTech 1404 2-ch Oscilloscope (100 MHz)
Specially developed for the education and hobby sector, this fully-fledged digital storage oscilloscope offers the best possible price/performance ratio without having to compromise on functionality or technical features. Whether Autoset and Autoscale, mathematical measurement functions, FFT, Cursor or XY mode and even a zoom function, all standard market functions are already integrated in this series. The data storage of the waveforms is either internal with memory for 16 waveforms or external on a USB memory in TXT, CSV or BIN format, which can be read out with the included software. Configurations can also be saved internally or screenshots of the display can be saved externally. The display of the waveforms can be achieved quickly and user-friendly through the Autoset function, via AutoScale the measured waveforms can be displayed even more precisely as required, whereby these settings can of course also be carried out completely manually via the key control. Features 2-channel oscilloscope with 100 MHz analogue bandwidth at max. 1 GS/s sampling rate 17.5 cm (7") TFT colour display with 800 x 480 pixels USB device connection for real-time data transmission USB host connection for external USB data carriers Handy and flat housing design with carrying handle Autoset function for user-friendly operation Recording length of max. 10,000 points Automatic measuring modes, XY mode and FFT function Specifications Bandwidth 100 MHz Channels 2 Sampling 1 CH 1 GS/s Sampling 2 CH 500 MS/s Rise Time Display Type Color TFT Resolution 800 x 480 Pixels Screen size (TFT) 17.5 cm (7") Hor. scale max. 1000 s/div Hor. scale min. 2 ns/div Memory depth 10,000 Points Vert. resolution 8 Bit Vert. scale max. 5 V/div Vert. scale min. 2 mV/div Mains voltage 110/240 V AC; 50/60 Hz Downloads User Manual Driver Software
€ 299,00
Members € 269,10
Miniware Miniware DS212 2-ch Mini Oscilloscope (1 MHz)
Features Synchronous mode: Auto, Normal, Single, None, Scan Rising/Falling edge trigger Modes of vertical precise, horizontal precise measurement and triggering threshold Auto Measurement: frequency, cycle time, duty cycle, DC RMS voltage/Vpp /Vmax/Vmin/Vavg Inbuilt signal generator/10 Hz-1 MHz square wave (duty adjustable) or 10 Hz-20 KHz Sine/Square/Triangle/Sawtooth wave Specifications Analog bandwidth 1 MHz Max sample rate 10 Msa/s Max sample memory depth 8K Analog input impedance 1 MΩ Max input voltage ±40 V (X1) Coupling AC/DC Vertical sensitivity 20 mv/Div~10 V/Div (1-2-5) Horizontal sensitivity 1 uS/Div~2 S/Div (1-2-5) Storage Built-in 8 MB U disk storage for waveform data and images Power supply Internal 550 mAh Lithium battery, recharging through Micro USB port Display 2.8" Full Color TFT LCD (320x240 pixels) Dimensions 100 x 56.5 x 10.7 mm Downloads User Manual Source Code App
€ 149,95
Members € 134,96
Uni-Trend UNI-T UPO1202CS 2-ch Oscilloscope (200 MHz)
UNI-T UPO1202CS is a multifunctional, low-cost 2-channel digital phosphor oscilloscope with 200 MHz bandwidth and 1 GSa/s sampling rate. It can be widely used in the fields of electronic and electrical design, debugging, education and industrial design. UPO1000CS series adopts parallel digital signal processing technology, which greatly improves the data processing speed and waveform capture rate. The original Ultra Phosphor technology can present the cumulative effect of the tested signal as a multi-layered afterglow. Compared with traditional digital storage oscilloscopes, the persistence of digital phosphor oscilloscopes can present three-dimensional waveform data of amplitude, time and signal intensity. Fast Acquire technology can accurately capture abnormal events such as video, jitter, noise and runt signals. Specifications UPO1102CS UPO1202CS Bandwidth 100 MHz 200 MHz Analog channels 2 2 Sampling rate 1 GSa/s 1 GSa/s Storage depth 56 Mpts per channel 56 Mpts per channel Rise time ≤3.5ns ≤1.8ns Capture rate 500,000 wfms/s 500,000 wfms/s Waveform record 100,000 frames 100,000 frames Features 7" WVGA (800 x 480) TFT LCD Ultra Phosphor super fluorescent display effect, up to 256 levels of gray display Support RS232, I²C, SPI, CAN and LIN trigger Innovative RS232, I²C, SPI, CAN and LIN hardware decoding Vertical scale: 1 mV/div-20 V/div Low background noise: 1M points enhanced FFT function. Support frequency setting, waterfall diagram, detection setting and marker measurement etc 36 kinds of waveform parameters can be automatically measured Rich trigger functions (edge, pulse width, video, slope, runt, overshoot, delay, timeout, duration, setup and hold, Nth edge and pattern trigger) Multi-Scopes support dual-channel independent trigger fluorescence display Multi-channel independent 7-bit hardware frequency counter DVM supports dual-channel independent AC and DC true RMS measurement Waveform arithmetic functions (FFT, +, -, ×, ÷, digital filtering, logic operations, and advanced operations) Rich interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail) Support SCPI programmable instrument standard command Support WEB access and control Downloads Datasheet Programming Manual User's Manual Quick Start Guide Software
€ 439,00
Members € 395,10
FNIRSI FNIRSI DSO152 Mini Oscilloscope (200 kHz)
The FNIRSI DSO152 is an extremely practical and cost-effective handheld oscilloscope with a real-time sampling rate of 2.5 MSa/s, a bandwidth of 200 kHz and complete trigger functions (single, normal and automatic). It can be used for both periodic analog signals and non-periodic digital signals and can measure voltages up to ±400 V. Equipped with an efficient one-key AUTO, it can display the measured waveform without cumbersome adjustments. It is equipped with a high-resolution 2.8-inch LCD screen with a resolution of 320x240 pixels and a built-in 1000 mAh high-quality lithium battery for up to 4 hours of operation. Specifications Sampling rate 2.5 MSa/s Bandwidth 200 kHz Vertical sensitivity 10 mV/DIV - 20 V/DIV (Progress according to the 1-2-5 way) Time base range 10µS/DIV - 50s/DIV (Progress according to the 1-2-5 way) Voltage range X1: ±40 V (Vpp: 80 V)X10: ±400 V (Vpp: 800 V) Trigger method Auto/Normal/Single Coupling method AC/DC Display 2.8" (320x240 pixels) USB charging 5 V/1 A Lithium battery capacity 1000 mAh Square wave calibration Frequency: 1K, Duty cycle: 50% Dimensions 99 x 68.3 x 19.5 mm Weight 100 g Included FNIRSI DSO152 Mini Oscilloscope Alligator clip probe USB cable Lanyard Manual Downloads Manual
€ 39,95
Members € 35,96
JYE Tech JYE Tech DSO Shell 150 Oscilloscope DIY Kit
Compared to DSO138, the new DSO Shell has similar bandwidth with significant improvements in structure, mechanical, and operation. The sensitivity has been extended in both directions : 5mV/div – 20V/div (DSO138: 10mV/div – 5V/div.Display and MCU are now mounted on the same mainboard to avoid inter-board pin-headers.For better separation between analog and digital circuits, the analog channel is on a separated board. Without the analog portion, the mainboard is actually a general-purpose control board. The mainboard is fully installed (except a few through-hole components), and factory tested.DSO Shell comes with an easy to modify enclosure. Rotary encoder makes parameter adjustment quick and easy.Power supply (not included): 9V (< 10V!) standard 5.5mm/2.1mm DC plug or 2-pin connector (0.1' pitch)Adequate soldering and troubleshooting skills required. Mainboard: 109-15000-00E or 109-15000-00E1 (Performance & assembly are identical) Analog board: 109-15001-00E or 109-15001-00F (Performance & assembly are identical) Product Documents and firmware: Users Manual (for 109-15001-00C analog board) Users Manual (for 109-15001-00E analog board) Schematic Main board schematic Analog board schematic Firmware How to Use the DSO150 Library Source code FAQ, Tips, and Troubleshooting Specifications Vertical Number of Channels 1 Analog Bandwidth 0 - 200 kHz Sensitivity 5 mV/Div - 20 V/Div Sensitivity error < 5 % Resolution 12-bit Input Impedance 1 MΩ Maximum Input voltage 50 Vpk Coupling DC, AC, GND Horizontal Max Real-time Sampling Rate 1 Msps Timebase 10 µs/Div - 500 s/Div Record Length 1024 Trigger Trigger Modes Auto, Normal, Single Trigger Types Rising / falling edge Trigger Position 1 / 2 of buffer size fixed Display 2.4-inch color TFT LCD 320 x 240 px Power Supply 9 V DC (8 - 10 V acceptable) Supply Current 120 mA @ 9 V Physical Dimensions 115 x 75 x 22 mm Weight 100 g without cables & power supply
€ 44,95
Members € 40,46
Uni-Trend UNI-T UPO1102CS 2-ch Oscilloscope (100 MHz)
UNI-T UPO1102CS is a multifunctional, low-cost 2-channel digital phosphor oscilloscope with 100 MHz bandwidth and 1 GSa/s sampling rate. It can be widely used in the fields of electronic and electrical design, debugging, education and industrial design. UPO1000CS series adopts parallel digital signal processing technology, which greatly improves the data processing speed and waveform capture rate. The original Ultra Phosphor technology can present the cumulative effect of the tested signal as a multi-layered afterglow. Compared with traditional digital storage oscilloscopes, the persistence of digital phosphor oscilloscopes can present three-dimensional waveform data of amplitude, time and signal intensity. Fast Acquire technology can accurately capture abnormal events such as video, jitter, noise and runt signals. Specifications UPO1102CS UPO1202CS Bandwidth 100 MHz 200 MHz Analog channels 2 2 Sampling rate 1 GSa/s 1 GSa/s Storage depth 56 Mpts per channel 56 Mpts per channel Rise time ≤3.5ns ≤1.8ns Capture rate 500,000 wfms/s 500,000 wfms/s Waveform record 100,000 frames 100,000 frames Features 7" WVGA (800 x 480) TFT LCD Ultra Phosphor super fluorescent display effect, up to 256 levels of gray display Support RS232, I²C, SPI, CAN and LIN trigger Innovative RS232, I²C, SPI, CAN and LIN hardware decoding Vertical scale: 1 mV/div-20 V/div Low background noise: 1M points enhanced FFT function. Support frequency setting, waterfall diagram, detection setting and marker measurement etc 36 kinds of waveform parameters can be automatically measured Rich trigger functions (edge, pulse width, video, slope, runt, overshoot, delay, timeout, duration, setup and hold, Nth edge and pattern trigger) Multi-Scopes support dual-channel independent trigger fluorescence display Multi-channel independent 7-bit hardware frequency counter DVM supports dual-channel independent AC and DC true RMS measurement Waveform arithmetic functions (FFT, +, -, ×, ÷, digital filtering, logic operations, and advanced operations) Rich interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail) Support SCPI programmable instrument standard command Support WEB access and control Downloads Datasheet Programming Manual User's Manual Quick Start Guide Software
€ 359,00
Members € 323,10
JYE Tech JYE Tech WAVE2 2-ch Portable Oscilloscope DIY Kit
Features No. of Channels: 2 Bandwidth: 0 – 200 KHz per channel Sensitivity range: 5 mV/DIV – 20 V/DIV (using x1 probe) Maximum input voltage: 50 Vpk (using x1 probe) Maximum real time sampling rate: 1 MS/s Time Base range 10 us/DIV – 500 s/DIV X-Y Display Feature: Yes Function Generator Capability: Built-in 0 – 20 KHz (sine) dual channel DDS function generator Display Resolution: 320 x 240 Color display Display Size: 2.4″ Touch Display Capability: Yes Battery powered and portable (battery not included in DIY Kit) Specifications General 2.4” 320x240 color display Touch panel operation Y-X mode available Built-in 2-channel DDS function generator Light weight and portable Vertical Number of Channel: 2 Analog Bandwidth: DC – 200 KHz Sensitivity: 5 mV/Div - 20 V/Div (with x1 probe) Sensitivity error: Resolution: 12-bit Input Impedance: 1 M ohm / 25 pF Maximum Input Voltage: 50 Vpk Coupling: DC, AC Horizontal Max Real-time Sampling Rate: 1 Msps (per channel) Timebase: 10 us/Div - 500 s/Div Record Length: 1024 points Trigger Trigger Modes: Auto, Normal, Single Trigger Types: Rising/falling edge Trigger Position: 1/2 of buffer size Trigger Source: Ch1, Ch2, External Maximum external trigger voltage: 15 V External trigger threshold: LVTTL Function Generator Number of channel: 2 Waveform type: Sine, Square, Saw-tooth, Stair Frequency range: DC – 20 KHz (Sine) Amplitude range: 0 – 3 V (peak value) Offset: 0 V or +3.3 V Duty Cycle: 0 – 100% Phase: -360 – 360 degree Power Supply Powered on 3.7 V Li-ion battery or USB Current consumption: ~30 0mA @ 3.7 – 5V Internal batter charger (optional) Automatic power off on battery Battery running time: Appr. 3 hrs (when fully charged) Other Features Y-X display mode On-screen measurement display Save / recall up to 4 captures Serial output of captured data Serial port format: LVTTL, 115200 bps, 8N1 Built-in 1 KHz/3.3 V test signal Physical Dimension: 115 x 72 x 30 mm Weight: 0.29 kg (excluding battery and probes)
€ 84,95
Members € 76,46
FNIRSI FNIRSI 1013D 2-ch Tablet Oscilloscope (100 MHz)
The FNIRSI 1013D is a fully featured 2-channel tablet oscilloscope with a high-resolution 7-inch LCD screen (800 x 480 pixels). The oscilloscope has a real-time sampling rate of 1 GSa/s and an analog bandwidth of 100 MHz. With full trigger functions (single/normal/automatic), it can be used for periodic analog signals or non-periodic digital signals. The built-in high-voltage protection module can withstand a continuous voltage of up to 400 V. Features Intelligent anti-burn,1X can withstand up to 400 V withstand voltage. 100 MHz analog bandwidth @ 1 GSa/s sampling rate (1X = 5 MHz,10X = 100 MHz). Fully fit 7-inch 800 x 480 resolution color TFT LCD display with bright colors and high contrast. Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation. High measurement voltage range, 1X can measure 0~40 V, 10X can measure 0~400 V,100X can measure 0~4000 V. Up to 12 parameters measurement: VPP, VP, Vmax, Vmin, Vavg, Vrms, Frequent, Duty+, Duty-, Time+, Time−, Period. Cursor measurement function, it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic). At any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO. One-button waveform storage and screenshot. Built-in 1 GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal. Built-in 6000 mAh rechargeable lithium battery, fully charged for 4 hours of continuous use at the highest screen brightness. Memory compression technology, waveform refresh screen does not flicker. Screen brightness adjustment. Background grid brightness adjustment. Applications Electronic DIY Appliance repair Car repair Equipment debug Scientific research Product development Specifications Channels 2 LCD size 7 inch LCD resolution 800 x 480 Display technology TFT Bandwidth 100 Mhz Sampling rate 1 GSa/s Rise time <3nS Storage depth 240 Kbit Input resistance 1 MΩ Sensitivity 50 mV ~ 500 V Time base 50S ~ 10nS Trigger mode Single/Normal/Auto Trigger edge Rising/Falling Coupling AC/DC Highest test voltage 1X: 40 V, 10X: 400 V Cursor Position XY, Trigger Y Roll mode Yes One button AUTO Yes Waveform storage 1000 pictures + 1000 waveforms Waveform manager Yes Voltage accuracy ±2% Frequency precision ±0.01% high precision Parameter 12 kinds in total Battery 6000 mAh Lithium Standby 4 hours Extension USB export Power supply USB-C, 5 V @ 2 A/3 A/4 A Dimensions 184 x 124 x 50 mm Weight 650 g Included 1x FNIRSI 1013D 2-ch Tablet Oscilloscope 2x 100 MHz Probes (1X and 10X) 1x USB charger 1x USB cable 1x Manual Downloads Manual
€ 159,95
Members € 143,96
PeakTech PeakTech 1265 2-ch Oscilloscope (30 MHz)
The PeakTech 1265 is an affordable 30 MHz 2-channel digital storage oscilloscope with a high-resolution TFT color display and extensive additional functions. It has a sampling rate of up to 250 MS/s and convinces with its high quality and easy handling with the best price/performance ratio. To quickly display each incoming waveform, simply press the Autoset key and the oscilloscope itself searches for the best possible display. With Autoscale, however, the scaling of the time base can be adjusted in a user-friendly manner. This oscilloscope has a VGA output for displaying the oscilloscope display on an external monitor or projector. Features 2-channel oscilloscope with 30 MHz analog bandwidth at max. 250 MS/s sampling rate 8 inch (20 cm) TFT color display with 800 x 600 pixels LAN, USB host, USB device & VGA interface Autoset function for user-friendly operation Recording length of max. 10,000 points Automatic measurement modes, XY mode and FFT function Specifications Bandwidth 30 MHz Channels 2 Screen size (TFT) 8" (20 cm) Resolution 800 x 600 Pixel Display Type Color-TFT Sampling 1 CH 250 MS/s Sampling 2 CH 125 MS/s Hor. scale max. 100 s/div Hor. scale min. 5 ns/div Memory depth 10,000 Points Rise Time Vert. resolution 8 Bit Vert. scale max. 10 V/div Vert. scale min. 2 mV/div Interfaces 1x USB, 1x LAN, 1x VGA Mains voltage 110/240 V AC; 50/60 Hz Included PeakTech 1265 Oscilloscope USB cable Software CD for Windows Power cord 2 probes BNC cable Carrying case Manual Downloads Software Datasheet_DE-EN Datasheet_FR Datasheet_IT Datasheet_ES
€ 459,00
Members € 413,10