Search results for "board"
M5Stack M5Stack Proto Board
PROTO board is used as a Core Extensions feature. Suitable with Arduino and ESP32
€ 7,95
Members € 7,16
SwiftIO - Swift-based Microcontroller Board
SwiftIO offers a full Swift compiler and framework environment that runs on the microcontroller. The SwiftIO board is a compact electronic circuit board that runs Swift on the bare metal, giving you a system that can be used to control all kinds of electronic projects. Features NXP i.MX RT1052 Crossover Processor with ARM Cortex-M7 core @ 600 MHz 8 MB SPI Flash, 32 MB SDRAM On-board DAPLink debugger On-board USB to UART for serial communication On-board RGB LED On-board SD socket 46x GPIO, 12x ADC, 14x PWM, 4x UART, 2x I²C, 2x SPI etc. Many additional advanced features to meet the needs of advanced users Zephyr RTOS support MadMachine IDE is the premier integrated development environment for SwiftIO, which makes it easy to write Swift code and download it to the board.
€ 74,95€ 59,95
Members identical
SparkFun Alchitry Ft Element Board
The Ft Element is equipped with four 50-pin board to board connectors on the underside and top of the board that snap to the Alchitry Au and Au(+) boards. It also adds a USB 3.0 200MB/s high-speed interface to your Alchitry board stack via the USB-C connector. Features USB-C connector w/ 200MB/s data rate to board to board connectors For use with projects that require data transfer rates greater than standard onboard USB to serial 12Mbaud 200 Mbps* ~ 191 Mbaud* - Note: this is not exact and depends on how you are using the Dev board in conjunction with the FT element board.
€ 44,95
Members € 40,46
iCEBreaker FPGA Development Board
The iCEBreaker FPGA board is an open-source educational FPGA development board. The iCEBreaker is great for classes and workshops teaching the use of the open source FPGA design flow through Yosys, nextpnr, IceStorm, Icarus Verilog, Amaranth HDL and others. This means the board is low cost and has a nice set of features to allow for the design of interesting classes and workshop exercises. At the same time it allows the user to use the proprietary vendor tools if they choose to. After the workshop the boards can be easily used as a development board as most GPIO are exposed, broken out and configurable through jumpers on the back of the board. There is only a minimal amount of buttons and LED that can't be disconnected and used for your own purposes. Documentation Workshop
€ 89,95
Members € 80,96
SparkFun SparkFun moto:bit - micro:bit Carrier Board (Qwiic)
Onboard each moto:bit are multiple I/O pins, as well as a vertical Qwiic connector, capable of hooking up servos, sensors and other circuits. At the flip of the switch, you can get your micro:bit moving! The moto:bit connects to the micro:bit via an updated SMD, edge connector at the top of the board, making setup easy. This creates a handy way to swap out micro:bits for programming while still providing reliable connections to all of the different pins on the micro:bit. We have also included a basic barrel jack on the moto:bit that is capable of providing power to anything you connect to the carrier board. Features More reliable Edge connector for easy use with the micro:bit Full H-Bridge for control of two motors Control servo motors Vertical Qwiic Connector I²C port for extending functionality Power and battery management onboard for the micro:bit
€ 109,95€ 79,95
Members identical
SB Components StackyPi - Raspberry Pi RP2040 based Board
StackyPi consists of standard Raspberry Pi 40 pins on its board for Raspberry Pi HAT. One can plug Raspberry Pi HAT by directly putting it on the StackyPi that has the power pins for the connection. StackyPi is a board on which, clear and descriptive pin labels make the process easier for the user. Features Dual Arm Cortex-M0+ processor 264 KB RAM DMA Controller Operating Voltage: 3.3 V GPIO / UART / SPI / I²C Pins: 40 Flash Memory: 64 MB Dimensions: 65 x 30 mm Downloads STEP File Product Dimension 3D PDF File Schematic File GitHub
€ 19,95
Members € 17,96
Get Started with the MAX78000FTHR Development Board
Build your own AI microcontroller applications from scratchThe MAX78000FTHR from Maxim Integrated is a small development board based on the MAX78000 MCU. The main usage of this board is in artificial intelligence applications (AI) which generally require large amounts of processing power and memory. It marries an Arm Cortex-M4 processor with a floating-point unit (FPU), convolutional neural network (CNN) accelerator, and RISC-V core into a single device. It is designed for ultra-low power consumption, making it ideal for many portable AI-based applications.This book is project-based and aims to teach the basic features of the MAX78000FTHR. It demonstrates how it can be used in various classical and AI-based projects. Each project is described in detail and complete program listings are provided. Readers should be able to use the projects as they are, or modify them to suit their applications. This book covers the following features of the MAX78000FTHR microcontroller development board: Onboard LEDs and buttons External LEDs and buttons Using analog-to-digital converters I²C projects SPI projects UART projects External interrupts and timer interrupts Using the onboard microphone Using the onboard camera Convolutional Neural Network
€ 32,95
Members € 29,66
SparkFun SparkFun Power Delivery Board - USB-C (Qwiic)
The Power Delivery Board uses a standalone controller to negotiate with the power adapters and switch to a higher voltage other than just 5V. This uses the same power adapter for different projects rather than relying on multiple power adapters to provide different output; it can deliver the board as part of SparkFun’s Qwiic connect system, so you won’t have to do any soldering to figure out how things are oriented. The SparkFun Power Delivery Board takes advantage of the power delivery standard using a standalone controller from STMicroelectronics, the STUSB4500. The STUSB4500 is a USB power delivery controller that addresses sink devices. It implements a proprietary algorithm to negotiate a power delivery contract with a source (i.e. a power delivery wall wart or power adapter) without the need for an external microcontroller. However, you will need a microcontroller to configure the board. PDO profiles are configured in an integrated non-volatile memory. The controller does all the heavy lifting of power negotiation and provides an easy way to configure over I²C. To configure the board, you will need an I²C bus. The Qwiic system makes it easy to connect the Power Delivery board to a microcontroller. Depending on your application, you can also connect to the I²C bus via the plated through SDA and SCL holes. Features Input and output voltage range of 5-20V Output current up to 5A Three configurable power delivery profiles Auto-run Type-C™ and USB PD sink controller Certified USB Type-C™ rev 1.2 and USB PD rev 2.0 (TID #1000133) Integrated VBUS voltage monitoring Integrated VBUS switch gate drivers (PMOS)
€ 34,95
Members € 31,46
Elektor Labs Elektor Raspberry Pi Buffer Board
When you experiment with the Raspberry Pi on a regular basis and you connect a variety of external hardware to the GPIO port via the header you may well have caused some damage in the past. The Raspberry Pi Buffer Board is there to prevent this! The board is compatible with Raspberry Pi Zero, 3, 4, 5 and 400. All 26 GPIOs are buffered with bi-directional voltage translators to protect the Raspberry Pi when experimenting with new circuits. The PCB is intended to be inserted in the back of Raspberry Pi< 400. The connector to connect to the Raspberry Pi is a right angled 40-way receptacle (2x20). The PCB is only a fraction wider. A 40-way flat cable with appropriate 2x20 headers can be connected to the buffer output header to experiment for instance with a circuit on a breadboard or PCB. The circuit uses four TXS0108E ICs by Texas Instruments. The PCB can also be put upright on a Raspberry Pi 3 or newer. Downloads Schematics Layout
€ 29,95€ 22,95
Members € 20,66
Evil Mad Science DIYIC Proto Board Kit
The matte-black circuit board is extra thick and has subtle white markings, including an alphanumeric grid and PIN labels. The wiring pattern — that of classic breadboards — is easy to see by looking at the exposed traces on the bottom of the board.The kit comes complete with the 'Integrated Circuit Leg' stand and 8 colour-coded thumbscrew terminal posts. Using the terminal posts and solder points, you can hook up to your 'IC' with bare wires, lugs, alligator clips, and/or solder joints. Connections to the 8 terminal posts are through the three-position strips on the PCB; each is labelled with the corresponding PIN.Features Anodized aluminium stand 8-32 size press-fit threaded inserts (8 pieces) pre-installed in the protoboard All materials (including the circuit board and stand) are RoHS compliant (lead-free) Tri lobular thread forming screws (6 pieces, black, 6-32 thread size) and spacers for mounting the stand. Dimensions: 13.25 cm × 8.06 cm x 2.54 mm Dimensions assembled: 13.25 cm × 9.9 cm × 4.3 cm
€ 34,95
Members € 31,46
SparkFun SparkFun GPS-RTK2 Board - ZED-F9P (Qwiic)
The SparkFun GPS-RTK2 raises the bar for high-precision GPS and is the latest in a line of powerful RTK boards featuring the ZED-F9P module from u-blox. The ZED-F9P is a top-of-the-line module for high accuracy GNSS and GPS location solutions, including RTK capable of 10 mm, three-dimensional accuracy. With this board, you will be able to know where your (or any object's) X, Y, and Z location is within roughly the width of your fingernail! The ZED-F9P is unique in that it is capable of both rover and base station operations. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1'-spaced pins if you prefer to use a breadboard. We've even included a rechargeable backup battery to keep the latest module configuration and satellite data available for up to two weeks. This battery helps 'warm-start' the module decreasing the time-to-first-fix dramatically. This module features a survey-in mode allowing the module to become a base station and produce RTCM 3.x correction data. The number of configuration options of the ZED-F9P is incredible! Geofencing, variable I²C address, variable update rates, even the high precision RTK solution can be increased to 20 Hz. The GPS-RTK2 even has five communications ports which are all active simultaneously: USB-C (which enumerates as a COM port), UART1 (with 3.3 V TTL), UART2 for RTCM reception (with 3.3V TTL), I²C (via the two Qwiic connectors or broken out pins), and SPI. Sparkfun has also written an extensive Arduino library for u-blox modules to easily read and control the GPS-RTK2 over the Qwiic Connect System. Leave NMEA behind! Start using a much lighter weight binary interface and give your microcontroller (and its one serial port) a break. The SparkFun Arduino library shows how to read latitude, longitude, even heading and speed over I²C without the need for constant serial polling. Features Concurrent reception of GPS, GLONASS, Galileo and BeiDou Receives both L1C/A and L2C bands Voltage: 5 V or 3.3 V, but all logic is 3.3 V Current: 68 mA - 130 mA (varies with constellations and tracking state) Time to First Fix: 25 s (cold), 2 s (hot) Max Navigation Rate: PVT (basic location over UBX binary protocol) - 25 Hz RTK - 20 Hz Raw - 25 Hz Horizontal Position Accuracy: 2.5 m without RTK 0.010 m with RTK Max Altitude: 50k m Max Velocity: 500 m/s Weight: 6.8 g Dimensions: 43.5 x 43.2 mm 2x Qwiic Connectors
€ 379,00
Members € 341,10
Evil Mad Science Easel Board for AxiDraw (Tabloid/A3)
Extra easel boards for AxiDraw V3/A3 can be used as replacements, or for staging additional workpieces for quickly swapping to the next plot. This set consists of one 11.75 x 17 inch (29.85 x 43.18 cm) hardboard platen with rubber feet attached, plus eight micro binder clips.
€ 17,95
Members € 16,16