Search results for "Micro pr"
SparkFun SparkFun Qwiic Pro Micro - USB-C (ATmega32U4)
This tiny little board does all of the neat Arduino tricks that you're familiar with: nine channels of 10-bit ADC, five PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 5 V and 16 MHz, this board will remind you a lot of your other favourite Arduino-compatible boards, but this little guy can go just about anywhere. There is a voltage regulator on board so it can accept voltage up to 6 VDC. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC. The reset button's benefit is to quickly reset the board or place it into bootloader mode without the need to take out a piece of the jumper wire. The USB micro-b connector has been replaced with the USB type C connector. The through-hole pads have castellated edges for each pin to add a lower profile in your projects should you decide to build it into another assembly during production. Finally, a Qwiic connector is populated on the board's bottom to add Qwiic enabled I²C devices to your projects easily! Features ATmega32U4 running at 5 V / 16 MHz AP2112 3.3 V Voltage Regulator Supported under Arduino IDE v1.0.1+ On-Board USB-C connector for programming PTH Pads w/ Castellated Edges 9 x 10-bit ADC pins 12 x Digital I/Os (5 are PWM capable) Hardware Serial Connections UART (i.e. Rx and Tx) Qwiic Connector for I²C SPI Small Arduino-Compatible Board Reset Button Dimensions: 1.3in x 0.7in
€ 24,95
Members € 22,46
Evil Mad Science EggBot Pro - Open-source Art Robot
The EggBot Pro is a complete re-imagining of the EggBot, designed for rigidity, ease of use, and faster setup. Its major components are solid aluminum, CNC machined in the USA, and powder coated or anodized. It's sturdy as can be. The frame has an open front, for greatly improved accessibility and visibility while you are plotting. The most common mechanical adjustments are faster with bicycle-style quick releases and repositioned thumbscrews for easier access. And, it comes fully assembled and ready to use. Assuming that you've installed the software first, you can be up and printing within minutes of opening the box. The EggBot Pro fits spherical and egg-shaped objects from roughly the size of a gumball to that of a light bulb — about 1 to 3.5 inches in diameter (2.5 - 9 cm). Perfect for ping pong balls, golf balls, chicken eggs, and similarly sized objects. The movements of the pen and egg motors are controlled by high-torque precision stepping motors, and the pen lift mechanism is a quiet and reliable servo motor. The included EiBotBoard v2.0 (EBB) driver board uses 16× micro stepping to give a resolution of 3200 steps/revolution in both axes. A universal-input plug-in power supply is included with the EggBot kit, as is a USB cable and one black Sharpie marker. To operate the EggBot Pro, you will need a reasonably modern computer with an available USB port (Mac, Windows or Linux), plus internet access to download the necessary software. The EggBot is usually controlled through a set of open-source extensions to Inkscape, the excellent, popular and free vector graphics program. The basic operation is much like that of a printer driver: you import or make a drawing in Inkscape, and use the extensions to plot your drawing onto whatever object you've mounted in the EggBot. It's all handled through an easy to use graphical user interface and works cleanly on Mac, Windows, and Linux. The standard pen holder included with the EggBot kit is designed to fit various art pens including Sharpie Ultra Fine Point and Sharpie Fine Point pens. However, it can fit almost any pen of similar size. You can even fit a lot of things that aren't pens. One example: We offer a diamond point engraving tool for EggBot (shown here), capable of etching and engraving hard materials like glass, stone, and ceramic.
€ 349,00
Members € 314,10
Arduino Arduino Pro Portenta Breakout
Portenta Breakout board is designed to help hardware engineers and makers to prototype and help test devices connections and capacity within the Portenta family boards (e.g. the Portenta H7). It makes all high-density connectors’ signals individually accessible, making it quick and easy to connect and test external hardware components and devices as normally needed during development in the lab. Features PowerON Button Boot mode DIP switch Connectors USB-A RJ45 up to 1Gb/s Micro-SD Card MIPI-20T-JTAG with Trace-Capability. Power CR2032 RTC-Lithium battery backup External power terminal block I/O Break out all Portenta High Density connector signals Male/female HD connectors allow interposing breakout between Portenta and shield to debug signals Compatibility Standard Portenta High Density connector pinout Specifications USB Port USB-A Ethernet RJ45 up to 1 Gb/s Memory slot Micro SD card Debug MIPI-20T-JTAG with trace capability Connectors HD Male/Female RTC power battery CR2032 Dimensions 164 x 72 mm Weight 69 g Downloads Datasheet Schematics Pinout
€ 59,95
Members € 53,96
Arduino Arduino Pro Portenta Max Carrier
Max Carrier transforms Portenta modules into single-board computers or reference designs that enable edge AI for high-performance industrial, building automation and robotics applications. Thanks to dedicated high-density connectors, it can be paired with Portenta X8 or H7, allowing you to easily prototype and deploy your industrial projects. This Arduino Pro carrier further augments Portenta connectivity options with Fieldbus, LoRa, Cat-M1 and NB-IoT. Among the many available plug-and-play connectors there are Ethernet, USB-A, audio jacks, microSD, mini-PCIe, FD-CAN and Serial RS232/422/485. Max Carrier can be powered via external supply (6-36 V) or battery via the onboard 18650 Li-ion battery connector with 3.7 V battery charger. Features Easily prototype industrial applications and minimize time to market A powerful carrier exposing Portenta peripherals (e.g. CAN, RS232/422/485, USB, mPCIe) Multiple connectivity options (Ethernet, LoRa, CAT-M1, NB-IoT) MicroSD for data logging operations Integrated audio jacks (line-in, line-out, mic-in) Standalone when battery powered Onboard JTAG debugger via micro-USB (with Portenta H7 only) Specifications Connectors High-Density connectors compatible with Portenta products2x USB-A female connectors1x Gigabit Ethernet connector (RJ45)1x FD-Can on RJ111x mPCIe1x Serial RS232/422/485 on RJ12 Audio 3x audio jacks: stereo line-in/line-out, mic-inSpeaker connector Memory Micro SD Wireless modules Murata CMWX1ZZABZ-078 LoRaSARA-R412M-02B (Cat.M1/NB-IoT) Operating temperatures -40 °C to +85 °C (-40° F to 185 °F) Debugging Onboard JLink OB / Blackmagic probe Power/battery Power Jack for external supply (6-36 V)On-board 18650 Li-ion battery connector with battery charger (3.7 V) Dimensions 101.6 x 101.6 mm (4.0 x 4.0") Downloads Datasheet Schematics
€ 439,00
Members € 395,10
JOY-iT JOY-iT Mega 2560 Pro
This JOY-iT microcontroller board opens the world of programming to you and offers you the same computing power as the Mega 2560, but with a smaller foot-print. It also has many more connectors than comparable boards (Arduino Uno). It is powered by the Arduino IDE and power can be supplied either via the USB port or the VIN pins. This allows you to use it safely with many other devices, e.g. desktop PC. Therefore the Mega 2560 Pro is highly integrable. Features Microcontroller ATmega2560 - 16AU Storage Flash 256 KB, SRAM 8 KB, EEPRom 4 KB Amount of Pins:Digital I/OPWM OutputAnalog Input 541516 Compatible with Arduino, Desktop PCs, etc. Special features USB Port or Power Pins for power supply Interface converter Micro USB to USB UART Size 55 x 38 mm Items delivered JOY-iT Mega 2560 Pro with Pins Further Specifications Input Voltage 7 - 9 Volt on Vin, 5 Volt on mUSB Logic level 5 Volt Output current 800 mA Voltage regulator LDO (for up to 12 V peak) Frequency 16 MHz (12 MHz are possible for data exchange) Download Manual
€ 29,95
Members € 26,96
Peak Peak Atlas DCA75 Pro Advanced Semiconductor Analyser
The DCA75 Pro is a great instrument that combines ease-of-use with amazing features. It can automatically identify a huge range of semiconductors, automatically identify pinouts and measure detailed parameters. Features Built-in graphics display (now backlit) to show detailed schematic of the component you're testing as well as pinout and measurement data. USB connectivity to allow curve tracing, data storage/retrieval and device matching on your Windows PC (Windows 7 and higher). Single internal AAA alkaline cell for standalone operation. Component Support Bipolar transistors (NPN/PNP inc Silicon/Germanium) Darlington transistors (NPN/PNP) Enhancement mode MOSFETs (N-Ch and P-Ch) Depletion mode MOSFETs (N-Ch and P-Ch) Junction FETs (N-Ch and P-Ch). Both symmetrical and asymmetrical types Enhancement IGBTs (N-Ch and P-Ch) Diodes and diode networks (2 and 3 lead types) Zener diodes (up to about 9 V) Voltage regulators (up to about 8 V) LEDs and bi-colour LEDs (2 lead and 3 lead types) Low power sensitive Triacs and Thyristors (<10 mA trigger and hold) Measurements BJT current gain (hFE) BJT base emitter voltage (Vbe) BJT collector leakage current MOSFET on and off gate threshold voltages MOSFET transconductance JFET pinch-off voltage JFET transconductance JFET IDSS (drain current for Vgs=0) IGBT on and off gate threshold voltages IGBT transconductance Voltage regulator output voltage Voltage regulator quiescent current consumption Voltage regulator drop-out voltage Zener voltage Diode forward voltage drop Specifications Analyser type Semiconductor components Component detection Automatic Pinout detection Automatic, connect any way round Display type Graphic LCD (now backlit) Interface type USB for optional PC connection PC functions Curve tracing (Windows 7 and higher) Software Included on USB drive for Windows 7 and higher Battery Single AAA cell (supplied) Included DCA75 Semiconductor Component Analyser PC software on a USB Flash Drive for Windows 11, 10, 8, 7, XP Micro USB cable Fitted universal premium hook probes AAA Alkaline battery Downloads Datasheet (EN) User Guide (EN) User Guide (FR) User Guide (DE) User Guide (IT) Software Installation Guide (EN) Software and Firmware Package
€ 169,95
Members € 152,96
Elecrow Raspberry Pi Pico Advanced Kit with 32 Modules and 32 Projects
This Raspberry Pi Pico advanced kit is designed for people who already have some electronics knowledge and programming skills and are interested in the Raspberry Pi. If you want to continue to strengthen your thinking, hands-on ability, and innovation ability, the Raspberry Pi Pico Advanced Kit will take you to create different scenarios and explore more applications. The Raspberry Pi Pico Advanced Kit includes a Raspberry Pi Pico H based on the official RP2040 chip, 32 sensor modules, 1 smart car kit, and 32 Raspberry Pi Pico projects. With this kit, you can complete several interesting and practical projects. In the process, the learners' thinking ability and creativity are continuously stimulated. Features Suitable for all users, from beginners to advanced programmers. 32 detailed lessons to lead your experiment 32 kinds of sensor modules and the smart cart can also be customized for interesting functions. Raspberry Pi Pico is a lightweight, compact, high-performance microcontroller multifunction board using a dual-core ARM Cortex-M0+ processor More powerful functions Projects RGB Colorful Light: Through PWM pulse width modulation, the LED light is controlled to light up gradually, and then gradually turn off, so as to form a breathing light effect in a cycle. Electronic Clock: The hour and minute data of the clock are displayed through the TM1637 4-Bits digital tube, and the clock point is controlled to flash circularly to make an electronic clock. Colorful Flowing Light: Through the GP port of the Pico, the 5 LED lights are controlled to light up in turn, and then turn off in turn to form a colorful flowing light. Billboard: The first line of LCD1602 scrolls from right to left to display the string of "Hello Pico", simulating the effect of billboard scrolling. Plant Doctor: Real-time detection of soil humidity. Under normal soil humidity, the green light lights up and the buzzer does not sound; when the soil humidity is too low, the red light lights up and the buzzer sounds. Alarm of Fire: Simulate a fire alarm system, judge whether a fire occurs by judging whether the induction probe of the flame sensor detects the fire source, control the RGB lights to flash red and blue, and display the alarm information on the LCD1602 liquid crystal screen. Obstacle Avoidance Car: Real-time detection of the distance measurement value of the ultrasonic ranging sensor, when the distance value is less than the preset value, the car will be controlled to turn left to avoid obstacles, so as to achieve the effect of the obstacle avoidance car. Traffic Light: Control the red light to turn on, the red light goes off after the 4-Bits digital tube counts down for 30 seconds; then the yellow light flashes 5 times with a time interval of 0.3 seconds. Finally the green light turns on for 10 seconds and then turns off, reciprocating, simulating the effect of traffic lights. Included 1x Raspberry Pi Pico H 2x 400 holes solderless breadboard 10x Colorful 5 mm LEDs: 1pcs each in green, red, blue, yellow and white 1x RGB module 1x Button 1x Sound sensor 1x Mini PIR motion sensor 1x Photoresistor module 1x Laser transmitter 1x Passive buzzer 1x Vibration sensor 1x Mini magnetic spring module 1x Soil moisture sensor 1x Rotary potentiometer 1x DC motor with male Dupont Wire + 1x fan blade 1x 9G servo 1x Dual-axis XY Joystick module 1x RC522 RFID module 1x 4 Bits digital LED display module 1x Traffic light display module 1x Rotary encoder module 1x 1602 LCD display module (blue) 1x Temperature & humidity sensor 1x Raindrops module 1x Flame mensor 1x OLED module 1x Membrane switch keyboard 1x Smart car kit 2x Crash sensor 2x Tracking sensor 1x Ultrasonic sensor 1x Infrared remote control 1x Infrared receiver module 1x Micro USB cable (30 cm) 1x 170 holes solderless breadboard 1x 65 Jumper wire 1x 20 cm Dupont wire (male to female) 1x Clear Case 2x M2.5x30 mm copper pillar 10x Phillips pan head screw 10x M2.5 Nickel hex nuts 1x 2-inch dual-purpose screwdriver 1x Magnet (Diameter: 8 mm, Thickness: 5 mm) 1x DC stepper motor driver board Downloads Tutorial Sample Code Map and Assembly Manual
€ 59,95
Members € 53,96
Arduino Arduino Pro Nicla Sense ME
The Nicla Sense ME is a tiny, low-power tool that sets a new standard for intelligent sensing solutions. With the simplicity of integration and scalability of the Arduino ecosystem, the board combines four state-of-the-art sensors from Bosch Sensortec: BHI260AP motion sensor system with integrated AI BMM150 magnetometer BMP390 pressure sensor BME688 4-in-1 gas sensor with AI and integrated high-linearity, as well as high-accuracy pressure, humidity and temperature sensors. The Arduino Nicla Sense ME is the smallest Arduino form factor yet, with a range of industrial grade sensors packed into a tiny footprint. Measure process parameters such as temperature, humidity and movement. Featuring a 9-axis inertial measurement unit and the possibility for Bluetooth Low Energy connectivity, it can help you to create your next Bluetooth Low Energy enabled project. Make your own industrial grade wireless sensing network with the onboard BHI260AP, BMP390, BMM150 and BME688 Bosch sensors. Features Tiny size, packed with features Low power consumption Add sensing capabilities to existing projects When battery-powered, becomes a complete standalone board Powerful processor, capable of hosting intelligence on the Edge Measures motion and environmental parameters Robust hardware including industrial-grade sensors with embedded AI BLE connectivity maximizes compatibility with professional and consumer equipment 24/7 always-on sensor data processing at ultra-low power consumption Specifications Microcontroller 64 MHz ARM Cortex-M4 (nRF52832) Sensors BHI260AP – Self-learning AI smart sensor with integrated accelerometer and gyroscope BMP390 – Digital pressure sensor BMM150 – Geomagnetic sensor BME688 – Digital low power gas, pressure, temperature & humidity sensor with AI I/O Castellated pins with the following features: 1x I²C bus (with ext. ESLOV connector) 1x serial port 1x SPI 2x ADC, programmable I/O voltage from 1.8-3.3 V Connectivity Bluetooth 4.2 Power Micro USB (USB-B), Pin Header, 3.7 V Li-po battery with Integrated battery charger Memory 512 KB Flash / 64 KB RAM 2 MB SPI Flash for storage 2 MB QSPI dedicated for BHI260AP Interface USB interface with debug functionality Dimensions 22.86 x 22.86 mm Weight 2 g Downloads Datasheet
€ 84,95
Members € 76,46
The Pi Hut ProtoDock - Prototyping Dock for Raspberry Pi 4
No more searching for micro-SD cards, SD adapters, USB-C adapters or USB devices. It’s all here, every time you’re ready to prototype a project, in one neat and tidy package. Our example configuration holds your Raspberry Pi 4, a 400-point clear breadboard, 4 micro-SD cards, an SD-adapter, 4x USB devices and 2x universal slots (great for USB-C adapters or anything else you want to store). You can of course use the storage slots for whatever you like... Customise it and use it in whatever way works best for you! Despite sitting flush with the top glass-effect acrylic layer of the dock, all of the Raspberry Pi’s ports are accessible, including access to the micro-SD slot. HATs can also be fitted. The dock is made up of 4 slick, sandwiched layers of matte black and glass-effect laser-cut acrylic! A really stunning and useful home for your Raspberry Pi and projects! Assembly guide available here. Kit includes 4 layer laser-cut acrylic dock 400-point clear breadboard Fixings and spacers
€ 16,95
Members € 15,26
PiKVM PiKVM V3 KVM over IP for Raspberry Pi 4 (pre-assembled)
PiKVM V3 HAT pre-assembled, in steel case with display and fan incl. Raspberry Pi 4 (2 GB) and 32-GB microSD card (pre-installed with PiKVM OS) PiKVM V3 is an open-source Raspberry Pi-based KVM over IP device. It will help you to manage servers or workstations remotely, whatever the state of the operating system or whether one is installed. PiKVM V3 allows you to turn on/off or restart your computer, configure the UEFI/BIOS, and even reinstall the OS using the virtual CD-ROM or flash drive. You can use your remote keyboard and mouse or PiKVM can simulate a keyboard, mouse, and a monitor, which are then presented in a web browser as if you were working on a remote system directly. Features HDMI Full HD capture based on the TC358743 chip (extra low latency ~100 ms and many features like compression control). OTG Keyboard & mouse; Mass Storage Drive emulation. Ability to simulate "removal and insertion" for USB. Onboard ATX power control Onboard fan controller Real-time clock (RTC) RJ-45 and USB serial console port (to manage PiKVM OS or to connect with the server). Optional AVR-based HID (for some rare and strange motherboards whose BIOS doesn't understand the OTG emulated keyboard). Optional OLED screen to display network status or other desired information. Ready-made board. No need for soldering or breadboarding. PiKVM OS – the software is fully open. Specifications Video/Resolution: 1920x1080p at 50 Hz or lower Power: USB-C 5.1 V, 3 A power supply required (not included) Real-time clock with rechargeable Super Capacitor Enclosure: robust 1.6 mm (1/16") steel case Dimensions: 92 x 75 x 45 mm (4 x 3 x 2") Weight: 410 g (14.5 oz.) Connectors Front Back Side Power: USB-C ATX Control Video Out: micro HDMI Serial Console: USB-C + RJ45(one active at a time) OTG Host USB (USB-C) 2x USB 2.0, 2x USB 3.0 HDMI Video input & output Gigabit Ethernet Included PiKVM V3 HAT for Raspberry Pi 4 PiKVM Steel Case incl. Display and Fan Raspberry Pi 4 with 2 GB RAM MicroSD card (32 GB, pre-installed with the PiKVM OS) USB-C bridge board – to connect the HAT with Pi over USB-C ATX controller adapter board and wiring – to connect the HAT to the motherboard (if you want to manage power supply through hardware). 2 flat CSI cables Screws and brass standoffs Required USB-C to USB-A cable HDMI cable Straight Ethernet cable (for the ATX expansion board connection) Power supply unit (5.1 V/3 A USB-C, officiel RPi power supply is recommended) Downloads User Guide Images GitHub Links The PiKVM Project and Lessons Learned: Q&A with PiKVM creator and developer Maxim Devaev PiKVM: Raspberry Pi as a KVM Remote Control
€ 349,00
Members € 314,10
SparkFun SparkFun MicroMod Artemis Processor
With a Cortex-M4F with BLE 5.0 running up to 96MHz and with as low power as 6uA per MHz (less than 5mW), the M.2 MicroMod connector allows you to plug in a MicroMod Carrier Board with any number of peripherals. Let's have a look at what this processor board has to offer! If you need Machine Learning capabilities, Bluetooth, I²C functionality to connect to all our amazing Qwiic boards, and more the Artemis Processor is the perfect choice for your MicroMod Carrier Board. At the heart of SparkFun's Artemis Module is Ambiq Micro's Apollo3 processor, whose ultra-efficient ARM Cortex-M4F processor is spec’d to run TensorFlow Lite using only 6uA/MHz. We've routed two I²C buses, eight GPIO, dedicated digital, analogue, and PWM pins, multiple SPI as well as QuadSPI, and Bluetooth to boot. You really can't go wrong with this processor. Grab one today, pick up a compatible carrier board, and get hacking! Features 1 M Flash / 384 k RAM 48 MHz / 96 MHz turbo available 6uA/MHz (operates less than 5mW at full operation) 48 GPIO - all interrupt capable 31 PWM channels Built-in BLE radio and antenna 10 ADC channels with 14-bit precision with up to 2.67 million samples per second effective continuous, multi-slot sampling rate 2 channel differential ADC 2 UARTs 6 I²C buses 6 SPI buses 2/4/8-bit SPI bus PDM interface I²S Interface Secure 'Smart Card' interface FCC/IC/CE Certified (ID Number 2ASW8-ART3MIS) 1x USB dedicated for programming and debugging 1x UART with flow control 2 x I²C 1 x SPI 1 x Quad-SPI 8 x Fast GPIO 2 x Digital Pins 2 x Analog Pins 2 x PWM 1 x Differential ADC pair Status LED VIN Level ADC
€ 18,95
Members € 17,06
The Pi Hut ZeroDock - Prototyping Dock for Raspberry Pi Zero
The default configuration holds a mini breadboard (included), an SD card adapter, 2x micro SD cards, 2x USB devices, a micro-USB shim and of course the Raspberry Pi Zero itself.Users can decide to use the micro-USB shim slot to hold a micro-HDMI adapter, or you may want to hold a Portsplus or similar GPIO reference card in the SD adapter slot. You can choose to store your USB micro-SD card reader or even other larger USB devices such as the USBDoctor. Use it in whatever way works best for you.All of the Raspberry Pi Zero ports are accessible from the ZeroDock, including the camera port and reset/composite pin header. pHATs are also not obstructed, so you’re free to prototype with your favourite add-on boards.The case is a stylish mix of clear and black acrylic layers, black fixings and a clear breadboard, fitting in well alongside most desktop PCs/monitors.Assembly guide available here.Kit includes 4 layer laser-cut acrylic case Case and Raspberry Pi fixings Mini breadboard
€ 14,95
Members € 13,46