NEW

Wide Range Power Supply for Raspberry Pi With the PiEnergy Mini, you can operate your Raspberry Pi with a voltage of 6 to 36 V DC. You can use the button integrated on the board to both power up and power down your Raspberry Pi. Communication with the Raspberry Pi is via GPIO4, but this connection can also be cut by removing a resistor to use the pin freely. Thanks to the ultra-flat design, it can also be used in many housings. The pin header is included and not soldered on to keep the design even flatter. Specifications Input voltage 6 to 36 V DC Output voltage 5.1 V Output current Up to 3 A (active ventilation recommended for additionally connected loads) Cable cross-section at the power input 0.2-0.75 mm² Interface to the Raspberry Pi GPIO4 Microcontroller ATtiny5 Further connections 5 V fan connector (2-pin/2.54 mm)Solder pads for external on/off switch Compatible with Raspberry Pi 3, 4, 5 Dimensions 23 x 56 x 11 mm Included Board with mounted heat sink Pin header (2x5) Spacer, screw, nut Downloads Datasheet (English) Datasheet (Italiano) Manual (English) Manual (Italiano)

Read more less

With the JOY-iT PS1440-C you get a programmable laboratory power supply, which provides you with DC voltages between 0.01 to 60 V and DC currents between 0.01 to 24 A at the voltage output. With the help of the intuitive control panel up to 9 different DC voltages can be programmed, stored and recalled, even individual settings of various protection and limiting functions (e.g. overvoltage protection) are programmable. The corresponding values can be set very conveniently via the keypad and/or the rotary control and are clearly displayed thanks to the high-resolution 2.4' color display. Features Complete device ready for immediate use Battery charging function Values can be entered conveniently via keypad Over current & over voltage protection adjustable Integrated RTC, NTC temperature sensor Included detailed documentation in English, German & French Specifications Input voltage 230 V Output voltage 0-60 V Output current 0-24 A Output power 0-1440 W Input voltage accuracy ±1% + 5 digits Output voltage accuracy ±0.3% + 3 digits Output current accuracy ±0.5% + 5 digits Battery voltage ±0.5% + 3 digits Input voltage measurement resolution 0.01 V Output voltage measurement resolution 0.01 V Current measurement resolution 0.01 V Battery voltage measurement resolution 0.01 V Response time in constant voltage mode 2 ms @ 0.1-5 A Load regulation in constant voltage mode ±0.1% + 2 digits Load regulation in constant current mode ±0.1% + 3 digits Measuring range electric charge 0-9999.99 Ah Measuring range energy 0-9999.99 Wh Statistical errors in electric charge & energy ±2% Output ripple 100 mV VPP @ 12 V150 mV VPP @ 24 V Sensor temperature detection range −10~+100°C (0-200°F) Sensor temperature detection accuracy ±3°C (±6°F) Working mode Step-down operation Screen brightness setting Level 0-5, 6 levels in total Permissible working temperature −10~+40°C (0-104°F) Dimensions 170 x 93 x 340 mm Included JT-PS1440-C power supply Power cord Manual Downloads Manual

Read more less

The Joy-Pi Advanced is a compact and powerful device that allows you to realize your projects quickly and easily. Whether you already have a lot of experience, or next to none, the Joy-Pi Advanced lets you unleash your creativity. Thanks to its compatibility with a wide range of platforms, including Raspberry Pi, Raspberry Pi Pico, Arduino Nano, BBC micro:bit, and NodeMCU ESP32, you can easily and quickly access your preferred platform. In addition, the Joy-Pi Advanced features more than 30 stations, lessons, and modules, giving you an unlimited variety of ways to get your projects done. With the self-developed learning center, you can not only improve your skills but also create new projects. The learning center offers a wealth of information and tutorials that will guide you step by step through your projects. Joy-Pi Advanced is characterized in particular by its intelligent switch units, which allow an extended use of the available pins. A total of three switch units are integrated, each equipped with 12 individual switches that provide precise control of the connected sensors and modules. This system solves the well-known problem of limited pin count that occurs with conventional microcontrollers. The switch units allow you to operate a large number of sensors and modules in parallel by switching them on and off individually. This simulates multiple pin assignment, allowing you to exploit the full power of your projects without compromising functionality. By combining innovative adapter boards and the micro:bit slot, you can achieve seamless compatibility with a wide range of microcontrollers such as Raspberry Pi Pico, NodeMCU ESP32, micro:mit and Arduino Nano. The specially developed adapter boards are designed to perfectly match the respective microcontroller. By plugging the microcontroller onto the appropriate adapter board and then plugging it into the micro:bit slot, the Joy-Pi Advanced quickly and easily becomes compatible with the different microcontrollers. This allows seamless integration of your preferred platform and the ability to combine the strengths of the different microcontrollers in your projects. This way, you can fully focus on your creative projects without worrying about the compatibility of different microcontrollers. The Joy-Pi Advanced simplifies the development process and gives you the possibility to design your projects flexibly and individually. Features Highly integrated development platform & learning center Fast, easy & wireless combination of various sensors & actuators Installation option for Raspberry Pi 4 Compatible with various microcontrollers Self-developed, didactic learning platform for Raspberry Pi & Windows Specifications Compatible to Raspberry Pi 4, Arduino Nano, NodeMCU ESP32, BBC micro:bit, Raspberry Pi Pico Installed sensors, actuators & components 39 Learning platform Over 40 entries in the know-ledge database, 10 projects, 10 learning tasks, 14 visions Displays 7-segment display, 16x2 display, 1.8“ TFT display, 0.96“ OLED display, 8x8 RGB matrix Sensors DS18B20, shock sensor, hall sensor, barometer, sound sensor, gyroscope, PIR sensor, Light barrier, NTC, Light sensor, 6x touch sensor, color sensor, ultrasonic distance sensor, DHT11 temperature & humidity sensor Control Joystick, 5x switches, potentiometer, rotary encoder, 4x4 button matrix, relays, PWM fan Motors Servo interface, Stepper motor interface, Vibration motor Measuring & conversion modules Analog-Digital Converter, Level converter, voltmeter, Variable voltage supply Other components RTC real time clock, buzzer, EEPROM memory, infrared receiver, breadboard, RFID reader Adapter boards Adapter for NodeMCU ESP32, Arduino Nano & Raspberry Pi Pico, Board connectors for Raspberry Pi & External Boards Electronic components Infrared remote control, RFID chip, RFID card, 6x alligator clips, microSD card reader, servo motor, stepper motor, 32 GB microSD card Components 40x resistors, 3x green LEDs, 3x yellow LEDs, 3x red LEDs, 1x transistor, 5x buttons, 1x potentiometer, 2x capacitors Other accessories Screw assortment, screwdriver, accessory storage bag, power supply & power cable, servo mount Power supply Built-in power supply: 36 W, 12 V, 3 A Case connector: Small device plug C8 Voltage outputs 12 V, 5 V, 3.3 V, Variable voltage output (2-11 V) Data buses & signal outputs I²C, SPI, Analog to digital converter Battery (RTC) CR2032 Dimensions 327 x 200 x 52 mm Required Raspberry Pi 4 Downloads Joy-Pi website Datasheet Manual

Read more less

The Explorer Board is the easy and efficient way to develop your Raspberry Pi Pico projects. Since the most important components are already integrated, you save time and effort on wiring. The Explorer Board has a wide range of interface connectors so you can connect your projects to a variety of modules and devices. With the integrated breadboard, you can quickly build and realize your own projects. Thanks to the possibility to connect or disconnect all modules individually, you can use your pins, which are additionally led separately to the outside, for other projects or experiment on the integrated breadboard at any time. Features Fast and efficient experimenting with the Raspberry Pi Pico Raspberry Pi Pico can be plugged in directly All modules can be switched on and off individually Additional integrated breadboard for own development Specifications Integrated modules: 4 RGB LEDs, buzzer, relay, 1.8“ TFT display, DHT11 temperature sensor, 4 buttons, breadboard Interfaces: 4x servo motor, SPI, I²C, UART, 5x crocodile clip connector Power supply: 5 V USB-C Dimensions: 219 x 110 x 27 mm Downloads Manual Examples and libraries

Read more less

The JT-RAD01 is a radiation meter for the detection of γ-, β- and X-ray radiation and is characterized by its particularly easy handling, high measurement stability and its handy and robust design. The meter has a large color LCD with backlight. The measurement results can be displayed both as clear statistics and graphically for easy evaluation. Specifications Detectable types of radiation γ-rays, β-rays, x-rays Measurement method Geiger-Müller Counter Dosis units μSv/h, μGy/h, mR/h, cps, cpm Alarm modes LED, vibration, sound Special features Real-time view and graph view, alarm when current and cumulative limits are exceeded Dosis rate 0.00 – 1000 μSv/h (10 mSv/h) Cummulative radiation dose 0.00 μSv – 500.0 mSv Energy range 48 keV – 1.5 MeV ≤±30% (CS-137) Sensitivity 80 CPM/μSv (Co-60) Battery 1100 mAh Lithium-ion Selectable languages English, German Dimensions 4.8 x 3.03 x 1.06' (122 x 77 x 27 mm) Included JT-RAD01 Nuclear Radiation Meter USB-C cable Manual (English/German)

Read more less

This LCR meter offers a wide range of functions at a low price. The LCR meter can measure capacitance, resistance, and inductance among other things. In addition, it can automatically recognize components, for example, it can distinguish between different types of transistors, such as NPN or PNP transistors. The device is particularly easy to operate, as all measurements are started at the touch of a single button. Thanks to the integrated 350 mAh battery, measurements can also be carried out on the road. The battery is charged with the help of a 5 V power supply unit (available separately) and the enclosed micro-USB cable. In addition, this measuring device can decode infrared signals and show them as a waveform on the display. Specifications Measurable components Resistor, capacitor, inductor, thyristor, triac, (double) diode, Z-diode, field effect transistor, bipolar transistor, infrared decoder Display type 3.5" TFT LCD (160 x 128 p) Special features Automatic calibration, One key operation Built-in battery Lithium Ion rechargeable, 3,7 V, 350 mAh Dimensions 90 x 70 x 27 mm Items delivered Tester, Micro-USB cable, Test clip, LED, Capacitor Measuring Ranges Capacitance 25 pF - 100 mF Resistance 0.01 Ω - 50 MΩ Inductance 0.01 mH - 20 H Battery 0.1 V - 4.5 V, 300 mAh Z-diode breakdown voltage 0.01 V - 30 V Z-diode 0.01 V - 4.5 V Diode UF < 4,5 V Thyristor / Triac IGT < 6 mA Downloads Manual

Read more less

This display correspond to the Nokia 5110 norm which makes it perfectly to display data or graphs of measured values on a microcontroller or a single-board computer. Additionally, the display is compatible to all Raspberry Pi, Arduino, CubieBoard, Banana Pi and microcontroller without additional effort. Specifications Chipset Philips PCD8544 Interface SPI Resolution 84 x 48 Pixels Power supply 2.7-3.3 V Special features Backlight Compatible to Raspberry Pi, Arduino, CubieBoard, Banana Pi and microcontroller Dimensions 45 x 45 x 14 mm Weight 14 g

Read more less

This flash memory allows you to store and read data externally via the SPI interface of your microcontroller. The control of the module is exactly the same as with a conventional SD card and is therefore particularly simple. The module is especially suitable for mobile setups, where normal SD cards could slip out of the SD card slot. Specifications Special feature 3 V and 5 V operation due to the integrated voltage converter Supply voltage Vcc 3-5 V Logic level Vcc Interface SPI Memory size 512 MB Clock frequency Up to 50 MHz Dimensions 18 x 22 x 12 mm Weight 3 g

Read more less

The BME680 from Bosch Sensortec is the new, compact ambient sensor with integrated sensor technology for humidity, pressure, temperature and air quality. The I²C and SPI digital interfaces also enable simple and fast readout of the measured values. Specifications Digital interfaces I²C, SPI Operating voltage 3-5 V Compatible to Arduino, Raspberry Pi Dimensions 30 x 14 x 10 mm Weight 10 g Humidity sensor Response time 8s Accuracy tolerance ± 3% Hysteresis ≤ 1.5% Pressure sensor Pressure range 300-1100 hPa Relative accuracy ± 0.12 hPa Absolute accuracy ± 1 hPa Temperature sensor Operating range -40°C - 85°C Full accuracy 0°C - 65°C Air quality sensor Response time 1s Downloads Datasheet Manual

Read more less

The SDS011 sensor determines the dust particle concentration in the air using the scattered light method. The USB-UART adapter also allows the sensor to be read out directly via USB port on a computer. Specifications Interface UART (3.3 V level) Resolution 0.3 µg/m3 Response time < 10s Other feature Integrated fan Current in idle < 4 mA Supply current 70 mA Operating voltage 5 V Dimensions 70 x 70 x 24 mm Weight 70 g Included 1x SDS011 dust sensor 1x Connection cable 1x USB-UART adapter Downloads Datasheet Manual

Read more less

The 1.28' LCD display convinces with its high-resolution IPS display and its circular display surface. With a color depth of 65,000 colors, the display is of particularly high quality. Due to the control via the SPI interface, the display is ideally suited for use as an output device on microcontrollers and single board computers. Specifications Interface 4-Wire SPI LCD type IPS LCD Display size 1.28' - Ø 32.4 mm Resolution 240 x 240 Pixels Display controller GC9A01 Depth of color 65,000 Operating voltage 3.3/5 V Dimensions 40 x 37 x 10 mm Weight 20 g Downloads Datasheet Manual

Read more less

This 7' touch display convinces with its variety of different application possibilities. The display can be connected via HDMI as well as via VGA. It has a 3.5 mm audio connector and a 4-pin JST-connector, to which headphones or two 2 W / 5 Ω speakers can be connected. The integrated software allows you to configure settings such as contrast and brightness using the buttons on the side. Specifications LCD type IPS Resolution 1024 x 600 Contrast 800:1 Brightness 350 CD/m² Multitouch Capacitive, 5 Points Connections Connections HDMI, VGA, Audio 3.5 mm, JST connector for two 2 W / 5 Ω speaker Power supply 5 V/2 A Viewing angle 175° Colors 16,7 M Further special features Additional solder pads to lead the buttons to the Dimensions 165 x 124 x 13 mm Included 1x 7' Display 1x microUSB-cable 1x VGA-cable 1x HDMI-cable 1x HDMI-microHDMI-cable Downloads Datasheet Manual

Read more less

With the NodeMCU-ESP32, comfortable prototyping is possible with simple programming via Luascript or the Arduino IDE and the breadboard-compatible design. This board has 2.4 GHz dual-mode Wifi and a BT wireless connection. In addition, a 512 KB SRAM and a 4 MB memory are integrated on the microcontroller development board. The board has 21 pins for interface connection, including I²C, SPI, UART, DAC and ADC. Specifications Type ESP32 Processor Tensilica LX6 Dual-Core Clock Frequency 240 MHz SRAM 512 kB Memory 4 MB Wireless Lan 802.11 b/g/n Frequency 2.4 GHz Bluetooth Classic / LE Data Interfaces UART / I²C / SPI / DAC / ADC Operating Voltage 3.3 V (operable via 5 V microUSB) Operating Temperature –40°C – 125°C Dimensions 48 x 26 x 11.5 mm Weight 10 g Downloads Manual

Read more less