Measuring Tools

Fumetractor – USB-Charge-Addon

Read more less

The Tabloid/A3 size Magnetic Easel is a sturdy work-holding tool that provides an alternative method of positioning paper or other workpieces for use with the AxiDraw V3/A3 and AxiDraw SE/A3. A heavy-duty alternative to the regular A3 clip easel, it can be used with binder clips or the (included) positioning rulers, magnets, and magnetic spring clips. The base of the easel is a heavy-gauge sheet of magnetic steel. It has a powder-coat finish, lightly textured to help hold paper in place and light gray in color for visible contrast against most types of paper. Rubber bumpers on the bottom side (along with the substantial weight of the steel) ensure a no-slip grip on your work table. To help index your paper in a consistent and reproducible position, the easel includes two six-inch (15 cm) rulers that you can rest your paper up against. The rulers are easy to remove and reversible, with inch and centimeter markings on the two sides. They can also be removed completely if you like, leaving just a flat sheet of steel (with a few ruler-mounting holes in it). This A3 easel also includes a special set of paper holding clips and magnets: Two special spring clips with magnetic bases, plus six skinny magnets for holding down paper. The two special spring clips each have two curved tines that apply gentle pressure to your paper. They allow you to slide paper directly in and out, quickly and easily, without touching any magnets, clips, or tape. They have a long reach to be positioned behind the rulers, or elsewhere if you prefer. Magnetic bases allow you to position them where needed. Two of these spring clips provide just enough pressure to keep a sheet of paper steady while you write or draw on it. This set also includes six cylindrical magnets, 4 mm in diameter and 10 mm tall, which are easy to position and firmly hold paper. The tall aspect ratio makes them particularly easy to grasp (unlike disc magnets). Perhaps more importantly, they tend to yield and tip over if hit by an errant pen tip, rather than holding so fast as to damage your pen or move your paper. Overall dimensions: 18.12 x 12.72' (46.0 x 32.3 cm) Suitable for use with A3 and US Tabloid/Ledger paper sizes, envelopes, two sheets of Letter or A4 paper, or smaller sizes of paper.

Read more less

The OWON XSA1015-TG Spectrum Analyzer offers a variety of features that will make it an indispensable part of your lab. Features Frequency Range from 9 kHz up to 1.5 GHz 150 dBm Displayed Average Noise Level Phase Noise -82dBc/Hz @1 Gz and offset at 10 KHz Total Amplitude Accuracy <1.5dB 10 Hz Minimum Resolution Bandwidth (RBW) EMI Pre-compliance Test Kit 1.5 GHz Tracking Generator Kit 10.4 inches display Specifications Frequency Specification Frequency Range 9kHz - 1.5 GHz Resolution 1Hz Frequency span Range 0 Hz, 100 Hz to maximum frequency of device Accuracy ± span /（swept points -1） Internal reference Reference frequency 10.000000 MHz Temperature stability < 2.5 ppm (15 ℃ to 35 ℃） Aging rate < 1 ppm / year Bandwidth Resolution bandwidth (-3 dB) 10 Hz to 500 kHz (in 1 to 10 sequence), 1 MHz, 3 MHz Video bandwidth (-3 dB) 10 Hz to 3 MHz Amplitude Specification Displayed average noise level（DANL） Input attenuation 0 dB，1Hz resolution bandwidth Preamp off 1 MHz ~ 10 MHz - 140 dBm（nominated）10 MHz ~ 1GHz - 140 dBm（nominated）1 GHz ~ 1.5 GHz - 138 dBm (nominated) Preamp on <-82 dBc / Hz @ 10 kHz offset<-100 dBc / Hz @ 100 kHz offset<-110 dBc / Hz @ 1 MHz offset Level display range Log scale coordinate 1 dB ~ 255 dB Linear scale coordinate 0 to reference level level unit dBm, dBuW, dBpW, dBmV, dBuV, W, V Points 201 ~ 1001 Number of traces 5 Detectors Positive-peak, negative-peak, sample, normal, RMS Trace functions Clear write, Max Hold, Min Hold, View, Blank, Average Accuracy Input Attenuation Switching Uncertainty 20℃ ~ 30℃, fc=50 MHz, Preamplifier Off, 20dB RF attenuation, input signal 0~39 dB±0.5 dB Absolute Amplitude Uncertainty 20℃ ~ 30℃, fc=50 MHz, RBW=1 kHz, VBW=1 kHz, peak detector, 20 dB RF attenuationPreamplifier Off ±0.4 dB, input signal= -20 dBmPreamplifier On ±0.5 dB, input signal= -40 dBm Uncertainty input signal range 0 dbm ~ -50 dbm±1.5 dB VSWR input 10 dB RF attenuation，1 MHz ~ 1.5GHz<1.5, nominal Tracking generator Output frequency range 100 kHz ~ 1.5 GHz Output power level range -30 dBm ~ 0 dBm Output power level resolution 1dB Output flatness +/-3 dB Maximum safe reverse level Average total power: 30 dBm, DC: ±50 VDC Inputs and Outputs Front panel RF input connector 50 Ω，N-type female Front panel track generator output 50 Ω，N-type female 10 M reference input 50 Ω，N-type female Communication port USB Host, USB Device, LAN, earphone port, and VGA General technical specification Display TFT LCD, 10.4 inches Weight 5.0 kg Dimension (W x H x D) 421 x 221 x 115 mm Downloads User manual Quick guide Datasheet PC software

Read more less

Peak UTP05E is a comprehensive CAT 5/5e/6 network cable analyser with superb accessories. Easy to use and very fast. Automatically identifies cable type (Straight through, cross-over, token ring etc) and verifies all the connections. Faults are clearly displayed and explained on screen. The Atlas IT will even instruct you on making up standard and special cables, complete with wire colors. Display type is alphanumeric LCD (not backlit). Features Automatic connection pattern recognition. Rapid assessment of all 8 wires within your cable. Identifies missing connections, shorted connections or incorrect connections. Will display the identity number of the 'identified' terminators to allow for easy testing and identification of multiple cable runs. Can display common cable colour codes to help you make up cables. Included UTP05 instrument. 2 miniature terminators to plug into another end of the cable run. 4 short patch cables to enable testing of patch panels and wall sockets. 24 miniature identified terminators, great for testing and identifying multiple cable runs. Pair of RJ11-to-RJ45 adapters to allow for easy testing of RJ11 based cabling. RJ45 to 8 x gold plated crocodile adapter for testing unterminated cables. Detailed printed user guide, complete with full-colour Ethernet wiring chart for common cable configurations. Alkaline battery installed and a spare alkaline battery. All supplied in a durable padded carry case. Specifications Category Cat 5, 5e, 6 (UTP) Connection type RJ45 plug or socket (RJ11 using supplied adapter set) Lines tested 8 lines (shielding not tested) Max. cable length 150 metres (500 feet) Test voltage ±5 V Test current ±2.5 mA Temperature range 10°C to 50°C (50°F to 122°F) Battery operating range 7 V to 13 V Battery type GP23, L1128, MN21, V23 (12 V Alkaline) Instrument dimensions 103 x 70 x 20 mm (4.1' x 2.8' x 0.8') Terminator dimensions 18 x 15 x 14 mm (0.7' x 0.6' x 0.6') Downloads Datasheet (EN) User Guide (EN) User Guide (DE) User Guide (FR) Common Ethernet Wiring Diagrams Avoid socket damage

Read more less

Keep printing with a pack of 4 nozzles (225 micron inner diameter). These metal dispensing tips offer excellent resolution and accurate deposition of ink and solder paste.

Read more less

T80-B (T80-D08) Soldering Tip for Soldering Station AE970D (0.8 mm, pointed)

Read more less

An SMD Magazine rail holds up to eight SMD Magazines. A given rail can be used to hold a project-specific set of magazines indefinitely. Magazines are held at a right angle, ready to be picked and placed by Pixel Pump. Each SMD-Magazine Rail presents up to eight magazines at the perfect angle for you to pick and place their components using Pixel Pump. You can also use these rails to group components for specific projects. They are equipped with non-slip rubber feet and weighted for extra stability.

Read more less

SMD Magazines are injection-molded containers and a great way to organize and consume SMD parts. They are custom built to store components and present them for picking. They can load up to 12-mm-wide, 9.5-mm tall tapes. They replace those hard-to-find plastic bags while being an excellent source of parts to pick and placing using Pixel Pump. Each SMD-Magazine Rail presents up to eight magazines at the perfect angle for you to pick and place their components using Pixel Pump. You can also use these rails to group components for specific projects. They are equipped with non-slip rubber feet and weighted for extra stability.

Read more less

Pixel Pump is an open source vacuum pump for manual SMT assembly. It comes with a comfortable pen, a foot pedal, RGB LED buttons, and a variety of features that make hand assembly a lot more fun. It’s the perfect companion for manual SMT soldering applications, from individual prototypes to small production runs. Thoughtful, High-Quality Design Pixel Pump ships with a set of five stainless-steel nozzles in each of five different sizes, with outer diameters ranging from 0.3 mm all the way up to 1.8 mm. With this set, you should be able to pick and place most SMD components, including small 0402 passives, larger parts like inductors and ICs, and just about everything in between. The nozzles are held in place by a Luer lock slip fitting that facilitates quick nozzle changes and broad compatibility with third-party nozzles. The pen itself features a barbed connection for the air hose and incorporates four M8 steel nuts to give it some heft and to enable magnetic attachment to Pixel Pump. Tactile silicone buttons with RGB backlighting offer full control over the unit. You can change operation modes, switch between high- and low-power settings, or activate reverse mode to clean your nozzle. The buttons also allow you to configure things like vacuum power and LED brightness. Pixel Pump has a pressure-relief valve that dumps vacuum to ensure that your part gets released quickly when you release the foot pedal. Optionally, you can configure that valve to switch from suction mode to pressure mode, which quickly and easily cleans the nozzle in case you have accidentally sucked in debris like solder paste. A sintered air filter protects the vacuum pump and valves from debris that might otherwise be sucked into the system. It is accessible from the outside and can easily be cleaned and reused. A Perfect Companion For Prototype Boards & Small-Scale Manufacturing Pixel Pump was designed primarily for individuals and organizations that manufacture one-off prototypes, but it’s also well suited for small production runs. It’s super easy to use and is actually faster than an automated pick-and-place machine for smaller batch sizes, especially when combined with SMD Magazines. Pixel Pump is the perfect companion for hobbyists and professionals who love making their own PCBs. Features Comfortable pen that accommodates various vacuum nozzles Small, flexible, heat-resistant silicone hose that connects the pen to Pixel Pump Magnetic base for the pen Strong, adjustable vacuum, perfect for picking small and large components alike Tactile, silicone RGB-button interface Foot pedal for triggering the pump Adjustable high/low power settings Adjustable LED brightness Reverse mode, which creates pressure instead of suction to clean nozzles Vacuum relief valve for quick depressurization to drop parts more quickly Easy software updates via USB Type-C Compact design that respects the limited surface area of your workbench Downloads 3D STL Files Firmware Mainboard Schematics UI Board Schematics Motor Controller Schematics

Read more less

iDraw is a versatile pen plotter, handwriting-imitated drawing machine and XY plotter. Based on open-source, iDraw is the best tool and aid for makers, geeks, DIYers, students, teachers with multi-functional features. It can imitate handwriting, draw masterpieces or cartoon, laser engrave on paper, leather, wood. Without soldering or programming, iDraw can run within several minutes. Specifications Version A4 Metal Charger DC 12 V/1 A Communication USB port, Offline Mode Unsupportable Mode Writing/Drawing/Laser Engraving Working Area 210 x 297 mm OS Windows/Mac/Linux Support Format INPUT/DRAW/SVG/JPG/BMP/PNG/DXF Repeatibility 0.1 mm XY Moving Precision 0.1 mm Motor 42 Stepper Motor, A4988 Driver Software Inkscape V1.0 Motherboard Drawcore, EBBV2.3 compatible Fireware Coding Type C, EBB Fireware Package 100 x 100 x 550 mm Weight 2.3 kg Downloads GitHub Software Step by step guide to assemble the hardware and install the software Seven Unboxing Tips for Metal iDraw How to assemble motors for iDraw How to install the servo and pen holder for iDraw What to buy a laser head? Video tutorials

Read more less

The SQ series of handsfree probes from Sensepeek have a lower point of gravity making them even more stable compared with the original SP series of handsfree probes. All probes in the SQ series are also insulated and can be used handheld as any traditional probe but their full potential is used when measuring handsfree. The SQ series of oscilloscope probes also includes more ground options, have probe tip protection, longer cable and support for oscilloscopes with automatic scaling (10:1). All the loved features of handsfree measurement, exchangeable fine pitch spring tipped test needle, color-coded cable holders and the minimalistic design is maintained to make traditional sized and handheld probes obsolete. Both length and weight of the SQ probes are perfectly balanced to be used with PCBite PCB holders and base plate which is a must for handsfree function. Features Passive 10:1 probe with support for oscilloscopes with automatic scaling Spring-loaded test needle for fine pitch measurements Multiple ground options Color coded cable holders Probe tip protection Insulated, can be used handheld Improved probe holder for handsfree measurement when used with PCBite PCB holders Included 1x SQ500 500 MHz probe with spring tipped test needle 1x SQ probe holder for handsfree measurement 1x Testhook with detachable cables (5 cm & 10 cm) for convenient ground connection 1x Alligator cable for convenient ground connection 1x Standard ground spring, for handheld measurements at rated bandwidth 1x Unique ground spring, for total handsfree measurements at rated bandwidth 1x Set of color coded cable holders (4 colors) 1x Probe tip protection 1x Extra test needle Downloads User Guide SQXX0 Rev1.1

Read more less

Features Safe Design: Pinter will be immediately shut off if the top cover has been removed. This feature is turned off by default. Anycubic Slicer Software: New features are added to the software. Supports up to 8x anti-aliasing: Fast slicing, Hollowing, Split Model, Text Paste. Fast Printing Speed: The time of exposure is as low as 1.5-2 seconds, and the max print speed is 60 mm/h, making printing speed 3x faster than the Photon. High Performance Z-axis: The Z-axis is supported by dual linear rails，stepper motor and clearance nut combination which dramatically improves stability while in motion and reduces the risk of layer shifting. New Matrix UV Light Source: High quality quartz lamp bead and new matrix design for uniform UV light energy. 4K monochrome LCD delivers high-quality prints Anycubic APP Remote Control: Remote control of print operations，monitor printing progress，adjust the print settings UV Cooling System: Cooling device for stable printing performance and longer service life. Large Build Volume: A large build area for your 3D-printed creations: 192 mm (L) x 120 mm (W) x 245 mm (H) 8.9″ 4K Monochrome LCD: Monochrome screens can last several thousand hours. Monochrome screens allow for very short layer exposure times for faster print times. Specifications System: ANYCUBIC Photon Mono X Operation: 3.5 inch Touch Screen Software: ANYCUBIC Photon workshop Connectivity: USB Technology: LCD-based SLA Light-source: high-quality filament（wavelength 405 nm) XY Res.: 0.050 mm 3840 x 2400 (4K) Z Axis Res.: 0.01 mm Layer Res.: 0.01-0.15 mm Printing Speed: Max 60 mm/h Rated Power: 120 W Printer Size: 270 mm (L) x 290 mm (W) x 475 mm (H) Build Volume: 192 mm (L) x 120 mm (W) x 245 mm (H) Material: 405 nm UV Resin Net Weight: ~10.75 kg Parts List User Manual SD-Card Tool set SD-Card Reader Scraper Resin Vat Platform Power Cord Service Card Wifi Antenna Glove

Read more less

T80-D (T80-D12) Soldering Tip for Soldering Station AE970D (1.2 mm, chisel)

Read more less

The 2-channel OWON XDG2035 is a function/waveform generator that can generate signals with a maximum frequency of 35 Hz. The generator has a resolution of 1 µHz and a sample rate of 500 MSa/s.The OWON XDG2035 is capable of generating 6 standard waveforms and 150 arbitrary waveforms. With the included software you can write advanced functions up to 10 million points. Waveforms can be saved to the function generator's internal memory using a PC via USB or LAN.The OWON XDG2035 also supports SCPI commands and LabView. The function generator has an integrated high-quality frequency counter, which can operate from 100 to 200 MHz.Features Max. 35 MHz frequency output 500 MSa/s Sample rate, Vertical resolution 1μHz 14 bits Vertical Resolution, 10 Marb waveform length Comprehensive waveform output: 6 basic waveforms,and 150 built-in arbitrary waveforms Comprehensive modulation functions: AM, FM, PM, FSK, 3FSK, 4FSK, PSK, OSK, ASK, BPSK, PWM, Sweep, and Burst High-accuracy frequency counter integrated, supported range 100-200 MHz SCPI and LabVIEW supported 7 inch multi-touch screen (800 x 480 pixels) Specifications Channel 2 Frequency Output 35 MHz Sample Rate 500 MSa/s Vertical Resolution 14 bits Waveform Standard Waveform sine, square, pulse, ramp, noise, and harmonic Arbitrary Waveform exponential rise, exponential fall, sin(x)/x, step wave, and others, total 150 built-in waveforms, and user-defined arbitrary waveform Frequency (resolution 1 μHz) Sine 1 μHz-100 MHz Square 1 μHz ~ 30 MHz Pulse 1 μHz ~ 25 MHz Ramp 1 μHz ~ 3 MHz Noise (-3 dB, typical) 100 MHz Arbitrary Waveform 1 μHz ~ 15 MHz Harmonic 1 μHz ~ 50 MHz Accuracy ±2ppm, 25°C ±5°C Waveform Length 2 points - 10M points Amplitude Into 50Ω load 1mVpp ~ 10Vpp (≤25 MHz); 1mVpp ~ 5Vpp (≤60 MHz); 1mVpp ~ 2.5Vpp (≤100 MHz) Modulation Type AM, DSB-AM, FM, PM, ASK, FSK, PSK, BPSK, QPSK, 3FSK, 4FSK, OSK, PWM, SUM Frequency Counter Function Frequency, period, +width, -width, +duty, and -duty Frequency Range 100 ~ 200 MHz Frequency Resolution 7 digits Input/Output Input mode frequency counter, external modulation input, external trigger input, internal clock output, external reference clock input/output Communication Interface USB Host, USB Device, LAN, RS232 (optional) Mechanical specifications Dimensions 340 x 177 x 90 mm Weight 2.3 kg Included 1x OWON XDG2035 1x Power Cord 1x CD-ROM 1x Quick start guide 1x USB Cable 1x BNC-BNC Cable DownloadsQuick Guide

Read more less

STEMlab 125-14 (originally Red Pitaya V1.1) is an open source measurement and control tool in size of a credit card (dimensions: 107 x 60 x 21 mm). It can replace many expensive laboratory measurement instruments. The STEMlab 125-14 unit is a network attached device based on Linux operating system. It includes Radio Frequency signal acquisition and generation technologies, FPGA, Digital Signal Processing and CPU processing. The STEMlab 125-14 unit is equipped with a Micro USB socket used for console connection, a microSD slot for microSD memory card, a RJ45 socket for Ethernet connection and a USB socket used for standard USB devices.Features High performance hardware at a surprising price tag. Replaces most essential instruments: (Oscilloscope, Spectrum analyser, Signal generator, LCR meter) LAN or wireless access from any WEB browser via tablet or a PC regardless of the OS (MAC, Linux, Windows, Android, iOS). LabView and MATLAB® interface. Possibility to make your own application and share it with others. Open source software. RF inputs Number of channels: 2 Bandwidth: 50 MHz (3 dB) Sample rate: 125 Msps Input impedance: 1 MΩ / 10 pF Connector: SMA-F RF outputs Number of channels: 2 Bandwidth: 50 MHz Sample rate: 125 Msps Load impedance: 50 Ω Connector: SMA-F Auxiliary analog input channels Number of channels: 4 Nominal sampling rate: 100 ksps ADC resolution: 14 bit Input voltage range: 0 to +3.5 V Input coupling: DC Connector: IDC connector Auxiliary analog output channels Number of channels: 4 Output type: Low pass filtered PWM PWM time resolution: 4ns (1/250 MHz) Output voltage range: 0 to +1.8 V Dimensions: 107 x 60 x 21 mmKit contents 1x STEMlab 125-14 board 1x Aluminium case 1x micro USB power supply adaptor 1x microSD card (4 GB) with pre-installed OS 1x Ethernet cable (1 m) 2x Osciloscope probes 2x SMA to BCN adapter 2x 50 ohm termination 2x SMA T adapter 1x WIFI dongle

Read more less

The Siglent SDS1204X-E is a powerful 200 MHz four-channel oscilloscope that is built on the same platform as the very popular SDS1202X-E but with several significant improvements, including two 1 GSa/s ADCs and two 14 Mpt memory modules. Waveform capture rates are up to 100,000 wfms/s in normal mode and 400,000 wfms/s in sequence mode. The SDS1000X-E scopes feature a large 7” 256-level color display with intensity grading and color temperature features.Specifications Model SDS1204X-E Bandwidth 200 MHz Sampling Rate (Max.) 1 GSa/s Channels 2CH+EXT4CH Memory Depth (Max.) 7 Mpts/CH (not interleave mode); 14 Mpts/CH (interleave mode) Waveform Capture Rate (Max.) 100,000 wfms/s (normal mode), 400,000 wfms/s (sequence mode) Trigger Types Edge, Slope, Pulse width, Window, Runt, Interval, Dropout, Pattern, Video Serial Trigger (Standard) I2C, SPI, UART/RS232, CAN, LIN Decode Type (Standard) I2C, SPI, UART/RS232, CAN, LIN 16 Digital Channels (four channel series only, option) Maximum waveform capture rate up to 1 GSa/s, Record length up to 14 Mpts/CH USB AWG module (four channel series only, option) One channel, 25 MHz, sample rate of 125 MHz, wave length of 16 kpts Bode plot ( four channel series only) Minimum start frequency of 10 Hz, minimum scan bandwith of 500 Hz, maximum scan bandwidth of 120 MHz (dependent on Oscilloscope and AWG bandwidth), 500 maximum scan frequency points USB WIFI adapter (four channel series only, option) 802.11b/g/b, WPA-PSK, the adapter must be supplied by Siglent to ensure proper functioning

Read more less

Components are both shrinking and getting increasingly finer pitch year after year but your PCBs might have grown in size or the number of interconnected PCBs or the number of handsfree PCBite probes needed to test your design may have increased making it crowded on our other smaller base plates. Features With a size of 297 x 420 mm (DIN A3) the extra large baseplate has room for most PCBs and many handsfree PCBite probes for those measurements sessions where more channels than available is needed. So if you are looking for more space, extra protection or just want to clean up your work surface then this accessory is a perfect match. Designed to be used with Sensepeeks magnetic PCBite line of products including PCB holders, hands free probes and magnifier. Included 1x XL base plate (DIN A3) with pre-fitted insulation cover

Read more less

Features Internal LNA amplifier and selectable attenuator Low frequency support from 50KHz covering LF, MF, HF, VHF and UHF up to 960Mhz New HELP and SET buttons to improve user interface and configuration selection with 2-clicks Wide band coverage to all popular sub-1Ghz bands, including FM, TV and DTV, ISM, RFID, GSM, etc. Ideal choice for HAM bands from 160meters to 33cm Pocket size and light weight Solid metal case Spectrum Analyzer mode with Peak Max and Hold, Normal, Overwrite and Averaging modes High capacity internal Lithium battery for 20hs+ of continuous run, rechargeable by USB Multi-platform Windows/Linux/MacOS Open Source software and API libraries Can be extended with internal Expansion Modules for additional band and functionality Specification Frequency band: 0.05 MHz - 960 MHz Frequency span: 0.1 MHz - 960 MHz Internal selectable LNA 25 dB gain Internal selectable Attenuator 30 dB Graphics LCD 128 x 64 pixels, great visibility outdoors Support included for Windows, Linux and MacOS X Backlight for great visibility indoor Internal Lithium Ion 1800mA/h rechargeable battery Standard SMA 50 Ω connector Wideband 144/433MHz dual band telescopic antenna included UHF 400-900 MHz rubber duck articulated antenna included Amplitude resolution: 0.5dBm Dynamic range: -125 dBm to 10 dBm Absolute Max input power: +30dBm Average noise level (typical LNA): -125 dBm Frequency stability and accuracy (typical): +-10 ppm Amplitude stability and accuracy (typical): +-2d Bm Frequency resolution: 1kHz Resolution bandwidth (RBW): automatic 2.6 kHz to 600 kHz Part List 1x Spectrum Analyzer 1x Mini USB cable 1x Dual band 144/430MHz Telescopic antenna 1x UHF 400-900Mhz antenna 1x EVA case

Read more less

Get creative and dispense your own fluids with this pack of cartridges.

Read more less

Looking to dispense materials with a lower viscosity? These are the nozzles for you. Don't use this with our standard ink or solder paste... that will result in poor performance.This pack contains 4 extra fine nozzles with an internal diameter of 0.100 mm (4 mil)

Read more less